TCD-1
TCD-2
INSTALLATION & OPERATING MANUAL
With ILLUSTRATED PARTS
NOTE: LIFT THE DISPENSER USING THE HANDLES ONLY. DO NOT LIFT THE DISPENSER FROM THE BOTTOM.
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
34106.0001L 11/06 © 2004 Bunn-O-Matic Corporation
INTRODUCTION
These dispensers are designed to mix liquid tea concentrate with water to produce iced tea by the glass or pitcher. The
concentrate can be stored either inside the dispenser, or outside with a hose connection to the dispenser. The dispenser
must be placed on a sturdy counter or shelf.
PLUMBING REQUIREMENTS
This dispenser must be connected to a cold water system with operating pressure between 30 and 90 psi
(138 and 620 kPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the
dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi
(345 kPa). The water inlet fitting is 1/4" flare.
NOTE - Bunn-O-Matic recommends 1/4" copper (or 3/8" braided flex) tubing for all installations from the 1⁄2"
water supply line. A tight coil of copper tubing in the water line will facilitate moving the dispenser to clean the
counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the dispenser. The size and
shape of the hole made in the supply line by this type of device may restrict water flow.
This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials
and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the
Food and Drug Administration (FDA). For models installed outside the U.S.A., you must comply
with the applicable Plumbing/Sanitation Code for your area.
USER NOTICES
Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should
be kept in good condition. Replace any unreadable or damaged labels.
This equipment must be installed to comply with the
PRESSURE REGULATOR ADJUSTMENT
Basic Plumbing Code of the Building Officials and
Code Administrators International, Inc. (BOCA) and
1. Pull Knob out to unlock.
the Food Service Sanitation Manual of the Food and
2. Adjust to 20 psi while faucet
is open, dispensing product.
3. Push knob in to lock.
Drug Administration (FDA). For models installed
outside the U.S.A., comply with the applicable
Plumbing /SanitationCode.
00656.0000
38465.0000
38130.0000
38466.0000
34106.1 060706
3
SET UP AND OPERATING PROCEDURES
1. Remove dispenser from the box and place on a sturdy, level counter.
2. Remove the brass cap and any packing material from the end of the water inlet fitting located on the rear of
the dispenser.
3. Attach the 1/4" "L" tube and water strainer to the water inlet fitting, tighten all flare nuts.
NOTE: The flow direction arrow on the strainer must point towards the dispenser.
4. Attach a 1/4" water line to the water strainer. This supply line must have at least 30 psi of pressure.
5. Using a screwdriver, turn the adjustment screw clockwise until the screw contacts the seat (DO NOT OVER-
TIGHTEN THIS SCREW!).
6. Turn on the water supply and open the water inlet valve on the rear of the dispenser and check for leaks in
the system.
7. Place a container under faucet(s); fully open the faucet(s) for approximately 10 seconds to remove all the air
out of the lines, then close the faucet(s). Discard the water.
8. Connect the proper BIB (Bag in a Box) adapter(s) to the concentrate inlet tube(s) and clamp. If bottle con-
centrate is used, connect the stainless formed tube(s) to the inlet hose(s) and clamp.
9. Attach the connector(s) to the BIB, or insert the bottle adapter into the bottle(s).
10. Place the concentrate container(s) in the location they will be used for normal operations.
a. In the dispenser housing: Coil the tube in the dispenser and place the BIB (bottle) on top of the coiled
tubing with the connector facing down, under the bag.
b. Under the counter: Place the BIB under the counter and rout the tubing to the dispenser, avoiding sharp
bends and kinks. Cut off excess tubing to keep the over length of tubing to minimum.
NOTE: It is critical that the dispenser is upright and the concentrate container(s) be in the proper location and
orientation that they will be during normal operation, before making any strength adjustments.
11. Slide the dispenser to the edge of the counter to gain access to the adjustment screw from the bottom.
12. Turn the adjustment screw approximately 1/2 turn counterclockwise.
13. Place a container under the faucet(s) and open faucet(s) until the entire concentrate line(s) fill and tea is
dispensed for approximately 5 seconds. Close the faucet(s). Discard this solution.
14. Place a glass under the faucet and open to fill the glass. Adjust the screw to achieve the desired strength
of tea. To increase the amount of concentrate (stronger tea), turn the adjustment screw counterclockwise
slightly (1/16 to 1/8 of a turn at a time). To reduce the amount of concentrate (weaker tea), turn the adjust-
ment screw clockwise slightly (1/16 to 1/8 of a turn at a time).
15. Dispense a couple of 8 ounce glasses of tea after each adjustment and test for taste or color. Continue this
process until the taste or color profile is achieved.
NOTE: The ratio adjustment setting is very sensitive. Make very small adjustments with the screw, then taste or
color check the results. You do not have to turn the screw very much to change the ratio.
16. Once the desired ratio of concentrate to water has been set, slide the dispenser back to the desired location
on the counter top. For under counter BIB’s, make sure the tubes do not get kinked, when the dispenser is
slid back into place.
The dispenser is now ready for use.
34106.1 100506
4
DISPENSER CLEANING AND SANITIZING
Daily Cleaning:
1. Turn handle on rear of dispenser to shut off the water supply.
2. Open the faucet to relieve pressure in the system.
3. Since the bag connector(s) have an internal shut off valve, it will be necessary to prop the valve open during clean-
ing.
NOTE: Cutting off the mating connector of an empty concentrate bag works well for this. Keep this mating end for future
cleanings of the system.
4. Turn on water supply to the dispenser.
5. Place the open bag connector into a 1/2 gallon container of dish soap and warm to hot water (130° F/54° C).
6. Place a large container under dispenser faucet.
7. Open faucet until the soap/water mixture in the container is empty.
8. After the soap mixture has been flushed through the system, fill the container with warm to hot tap water only (no
soap) and repeat steps 5 thru 7 until all soap has been flushed from the system.
9. Remove the mating end of connector and attach dispenser’s connector to a Bag In a Box and dispense several cups
to prime the concentrate line or until consistency of the product is correct.
10. Wash the entire outside surface of dispenser with a clean, damp cloth.
NOTE: When the system is not in use for extended periods of time (nights, weekends, etc.), turn the water supply valve
off.
Weekly Cleaning:
1. Turn handle on rear of dispenser to shut off the water supply.
2. Open the faucet to relieve pressure in the system.
On models with chrome nut (Complete Step 3, then skip to Step 6):
On models with wing nut (Skip Step 3 - Start at Step 4):
3. Unscrew the faucet bonnet (a) and remove all faucet components, leaving the faucet body (b) in place on the venturi
assembly.
4. Twist the faucet wing nut in a clockwise direction and remove faucet from the dispenser.
5. Remove and clean the O-ring (Optional).
a. Remove the o-ring from the venturi assembly nozzle. Be very careful when removing this o-ring.
Do Not scratch or nick the o-rings sealing surface when removing.
b. Clean the groove and o-ring with the same solutions as used to clean the faucet, Step 6.
c. When finished, slide the o-ring back into the groove on the venturi nozzle.
6. Sanitizing the faucet:
This procedure requires three cleaning solutions of approximately ½ gal each, a mild detergent and warm
water solution, clean hot water only and a warm chlorine solution (at least 50 ppm of chlorine at 75° F [24°
C]). NOTE: DO NOT use full strength bleach.
a
b
a. Disassemble the faucet.
b. Thoroughly wash all faucet parts in the mild detergent solution.
c. Rinse the parts in hot water.
d. Sanitize the parts by soaking for one minute in the warm chlorine solution.
e. Re-rinse the parts in hot water to remove all the chlorine solution.
f. Reassemble the faucet and attach it to the dispenser.
7. Sanitizing the BIB connector, tubing and metering valve:
This procedure requires a 1/2 gallon container of sanitizing solution, (100 ppm of chlorine at 100° F (38° C) water).
a. Since the bag connector(s) have an internal shut off valve, it will be necessary to prop the valve open during clean-
ing. NOTE: Cutting off the mating connector of an empty concentrate bag works well for this. Keep this mating end for
future cleanings of the system.
b. Turn on water supply to the dispenser.
c. Place open bag connector into the 1/2 gallon container of sanitizing solution.
d. Place a large container under dispenser faucet.
e. Open faucet until the chlorine mixture in the container is empty.
f. Allow dispenser to sit overnight before flushing sanitizer out of the system.
g. Flush system by filling a container with warm to hot tap water only (no chlorine) and opening the faucet - until all
chlorine has been flushed from the system.
8. Remove the mating end of connector and attach dispenser’s connector to a Bag In a Box and dispense several cups
to prime the concentrate line or until consistency of the product is correct.
34106.1 100506
5
TCD-1
TCD-2
REPLACEMENT PARTS (TCD-1)
60
61
63
62
61
47
.375" BIB Adapter
Concentrate Bottle Tube
23
46
27
28
29
50
21
51
20
49
48
22
10
19
18
30
31
32
33
17
16
15
14
13
12
11
10
26
35
36
34
24
23
25
23
38
58
1
39
56
55
5
37
6
57
40
41
42
7
8
9
2
3
43
45
44
4
53
52
51
54
59
P3457.60
34106.1 112106
6
REPLACEMENT PARTS (TCD-1)
ITEM
PART NO.
23820.1000
22249.0000
23721.0000
23819.0000*
00310.0006
00459.0001
01532.0000
00463.0000
37689.0000
32891.0001
33113.0000
QTY.
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
2
1
Water Strainer Assy (Includes items 2 thru 4)
2
Cap, Water Strainer
3
Screen
4
Housing (Order item 1)
5
Tube Assy, Strainer to Bulkhead
Fitting, Bulkhead
6
7
Lockwasher, Internal Tooth .438"
Nut, .438" - 20
8
9
Tube Assy, Bulkhead to Shut-off
Elbow, Male .25" FLR x .25" MPT
Valve, Ball .25" FPT x .25" FPT
10
11
12
32360.0001
01315.0000
00970.0000
2
1
2
Clamp, .613" ID
Screw, Truss Head #8-32 x .375"
Nut, Keps #8
13
14
15
16
17
18
19
20
21
22
23
24
25
26
37898.0000
37742.0001
00432.0001
00430.0001
21993.0001
00425.1000
12422.0006
33027.0000
37721.0001*
37721.0000*
12422.0001
33027.0001
37720.0000*
1
1
1
1
1
1
4
1
1
1
4
1
1
Gauge, Pressure
Nipple, .25" MPT
Elbow, .125" NPT Male/Female
Adapter, .125" NPT Male/Female
Regulator, Water, Low Flow
Fitting, .25" FLR Swivel Nut x .25" Barb
Clamp, Hose .53"/.59"
Valve, Check .25" Barb
Tube, Silicone .25" ID x 6.0" (Order item 66)
Tube, Silicone .25" ID x 3.5" (Order item 66)
Clamp, Hose .59"/.66"
Valve, Check .375" Barb
Tube, Silicone .375" ID x 3.0" (Order item 67)
37736.1000
37736.1001
38044.0000
1
1
2
Venturi Assy (.25" product delivery tubing)(Includes item 27-29, 31-33 & 36)
Venturi Assy (.375" product delivery tubing)(Includes item 27 thru 33 & 36)
Screw, Plastite #6 x .375"
NOTE: Effective August 2006, the Venturi and product delivery tubing was changed from .25"ID to .375"ID to improve
flow rate. If for first replacement, order Tube Replacement Kit P/N 39169.0000 (2 kits required for TCD-2)
(continued)
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.
34106.1 112106
7
TCD-1
TCD-2
REPLACEMENT PARTS (TCD-1)
(continued)
60
61
63
62
61
47
.375" BIB Adapter
Concentrate Bottle Tube
23
46
27
28
29
50
21
51
20
49
48
22
10
19
18
30
31
32
33
17
16
15
14
13
12
11
10
26
35
36
34
24
23
25
23
38
58
1
39
56
55
5
37
6
57
40
41
42
7
8
9
2
3
43
45
44
4
53
52
51
54
59
P3457.60
34106.1 112106
8
REPLACEMENT PARTS (TCD-1)
ITEM
PART NO.
QTY.
DESCRIPTION
27
37786.0001
01360.0002
2
2
Plate, Fitting Retainer
Screw, Plascrew #6 x .375"
28
29
30
31
32
33
34
35
32631.0000
32849.0001
32631.0001
37487.1000
37691.0000
37486.0000
32852.0000
1
2
1
1
1
1
1
Fitting, Barb .25"
O-ring
Fitting, Barb .375"
Venturi Mixer (Includes item 36)
O-ring
Adjustment Screw, Venturi
O-ring
03093.0001
01268.0000
1
1
Wing Nut, Faucet
Chrome Nut, Faucet Union (Optional)
36
37
01221.0001
03260.0004
1
1
C-Ring, Faucet Shank
Faucet Assy, Black Plastic Body (Includes items 38 thru 44)(Refer to page 18 for
important ordering information)(See item 70)
03260.0005
29163.0007
29165.0002
00601.0001
37715.0000
29164.0000
00600.0001
1
1
1
1
1
1
1
Faucet Assy, Chrome Body (Includes items 38 thru 45)(See item 70)
38
39
40
41
42
43
44
Handle, Faucet
Bonnet, Faucet
Spring Faucet
Collar, Spring (Refer to item 69)
Stem, Faucet
Seat Cup, Faucet (Refer to item 69)
35758.0002*
35206.0000*
1
1
Faucet Body, Black Plastic (Order item 37)
Faucet Body, Chrome (Order item 37)
45
46
38473.0000
1
Insert
- - - - - - - -
37720.0003*
1
1
Tube, Silicone .25" ID x 36.0" (For first replacement, order item 72)
Tube, Silicone .375" ID x 36.0" (Order item 67)
47
48
49
50
51
52
53
34093.0000
01592.0000
03043.0006
38130.0000
38278.0002*
38029.1000
03229.0000
1
2
1
1
2
1
1
Lid, Reservoir
Bushing, 1.0" Dia
Decal, Iced Tea (See page 18 for proper placement)
Decal, Faucet Under Pressure
Edging 36.0" (Order item 71)
Drip Tray Assy (Includes items 53 & 54)
Drip Tray Cover
(continued)
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.
9
34106.1 112106
TCD-1
TCD-2
REPLACEMENT PARTS (TCD-1)
(continued)
60
61
63
62
61
47
.375" BIB Adapter
Concentrate Bottle Tube
23
46
27
28
29
50
21
51
20
49
48
22
10
19
18
30
31
32
33
17
16
15
14
13
12
11
10
26
35
36
34
24
23
25
23
38
58
1
39
56
55
5
37
6
57
40
41
42
7
8
9
2
3
43
45
44
4
53
52
51
54
59
P3457.60
34106.1 112106
10
REPLACEMENT PARTS (TCD-1)
ITEM
54
PART NO.
03207.0004
38465.0000
38466.0000
00651.0000
00656.0000
38839.0000
QTY.
DESCRIPTION
1
1
1
1
1
1
Drip Tray
55
Decal, Pressure Regulator
Decal, Shut-off
56
57
Decal, BUNN
58
Decal, Plumbing Code
Stand (Optional)
59
60
26443.0000
34644.0000
1
1
Reducer, Barb .375" x .25"
Connector, Barb .375" x .375"
61
62
12422.0001
2
Clamp, Hose .59"/.66"
For use with .375" BIB adapter
37720.0000*
38295.0000*
1
1
Tube, Silicone .375" ID x 3.0" (Order item 67)
Tube, Silicone .375" ID x 36.0" (Order item 67)
63
37744.0000
37744.0001
1
1
Tube, Concentrate Bottle .25"
Tube, Concentrate Bottle .375"
Optional
64
65
66
00674.0000
M2531.0000
1
1
Brush, Tube .75" (Not illustrated)
Lube&Sealant Compound (Not illustrated)
37721.1000
37721.1001
37721.1002
-
-
-
Tube, Silicone .25" ID x 12.0"
Tube, Silicone .25" ID x 36.0"
Tube, Silicone .25" ID x 120.0"
67
68
37720.1000
37720.1001
37720.1002
-
-
-
Tube, Silicone .375" ID x 12.0"
Tube, Silicone .375" ID x 36.0"
Tube, Silicone .375" ID x 120.0"
37747.1000
37747.1001
-
-
Parts Bag (Includes items 1,5,23,37,49 & 63)(with 3.0" BIB hose)
Parts Bag (Includes items 1,5,23,37,52,62 & 63)(with 36.0" BIB hose)
69
70
71
72
38471.0000
28707.0004
38278.1002
39169.0000
-
-
-
-
Kit, Faucet Seat Cup (Includes items 41 & 43)
Kit, Faucet Repair (Includes items 38 & 40-43)
Edging 36.0" (Use as required)
Tube Replacement Kit (Includes items 23,24,25,30 & 46)
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.
11
34106.1 082506
TCD-1
TCD-2
REPLACEMENT PARTS (TCD-2)
65
66
53
50
51
52
51
Concentrate Bottle Tube
54
.375" BIB Adapter
51
49
Bag Divider
30
59
63
31
33
24
22
10
18
32
34
35
36
19
20
17
26
21
16
15
25
23
19
37
39
29
38
14
13
12
11
10
27
58
41
42
1
5
40
51
28
6
43
44
61
62
7
60
8
9
45
46
48
47
2
3
4
56
57
55
64
63
P3462.60
34106.1 112106
12
REPLACEMENT PARTS (TCD-2)
DESCRIPTION
ITEM
PART NO.
23820.1000
22249.0000
23721.0000
23819.0000*
00310.0006
00459.0001
01532.0000
00463.0000
37689.0000
32891.0001
33113.0000
QTY.
1
2
1
1
1
1
1
1
1
1
1
2
1
Water Strainer Assy (Includes items 2 thru 4)
Cap, Water Strainer
3
Screen
4
Housing (Order item 1)
Tube Assy, Strainer to Bulkhead
Fitting, Bulkhead
5
6
7
Lockwasher, Internal Tooth .438"
Nut, .438" - 20
8
9
Tube Assy, Bulkhead to Shut-off
Elbow, Male .25" FLR x .25" MPT
Valve, Ball .25" FPT x .25" FPT
10
11
12
32360.0001
01315.0000
00970.0000
3
1
3
Clamp, .613" ID
Screw, Truss Head #8-32 x .375"
Nut, Keps #8
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
37898.0000
37742.0001
00432.0001
00430.0001
21993.0001
00425.1000
12422.0000
37721.0004*
38023.0000
01592.0000
37721.0006*
03043.0006
12422.0006
33027.0000
33027.0001
1
1
1
1
1
1
3
2
1
4
2
1
5
1
2
Gauge, Pressure
Nipple, .25" MPT
Elbow, .125" NPT Male/Female
Adapter, .125" NPT Male/Female
Regulator, Water, Low Flow
Fitting, .25" FLR Swivel Nut x .25" Barb
Clamp, Hose .47"/.54"
Tube, Silicone .25" ID x 2.0" (Order item 69)
Y-Fitting, Barb .25" Hose
Bushing, 1.0" Dia
Tube, Silicone .25" ID x 4.75" (Order item 69)
Decal, Iced Tea (See page 18 for proper placement)
Clamp, Hose .53"/.59"
Valve, Check .25"
Valve, Check .375"
- - - - - - - -
37720.0000*
2
2
Tube, Silicone .25" ID x 3.5" (If for first replacement, order item 75)
Tube, Silicone .375" ID x 3.0" (Order item 70)
29
37736.1000
37736.1001
01360.0002
2
2
4
Venturi Assy (.25" product delivery tubing)(Each includes items 30,31, 33-36 & 39)
Venturi Assy (.375" product delivery tubing)(Each includes items 30 thru 36 & 39)
Screw, Plascrew #6 x .375"
NOTE: Effective August 2006, the Venturi and product delivery tubing was changed from .25"ID to .375"ID to improve
flow rate. If for first replacement, order Tube Replacement Kit P/N 39169.0000 (2 kits required for TCD-2)
(continued)
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.
13
34106.1 112106
TCD-1
TCD-2
REPLACEMENT PARTS (TCD-2)
(continued)
65
66
53
50
51
52
51
Concentrate Bottle Tube
54
.375" BIB Adapter
51
49
Bag Divider
30
59
63
31
33
24
22
10
18
32
34
35
36
19
20
17
26
21
16
15
25
23
19
37
39
29
38
14
13
12
11
10
27
58
41
42
1
5
40
51
28
6
43
44
61
62
7
60
8
9
45
46
48
47
2
3
4
56
57
55
64
63
P3462.60
34106.1 112106
14
REPLACEMENT PARTS (TCD-2)
ITEM
PART NO.
QTY.
DESCRIPTION
30
37786.0001
38044.0000
2
2
Plate, Fitting Retainer
Screw, Plastite #6 x .375"
31
32
33
34
35
36
37
32631.0000
32631.0001
32849.0001
37487.1000
37691.0000
37486.0000
1
1
2
1
1
1
Fitting, Barb .25"
Fitting, Barb .375"
O-ring
Venturi Mixer (Includes item 39)
O-ring
Adjustment Screw, Venturi
03093.0001
01268.0000
2
2
Wing Nut, Faucet
Chrome Nut, Faucet Union (Optional)
38
39
40
32852.0000
01221.0001
03260.0004
2
2
2
O-ring
C-Ring, Faucet Shank
Faucet Assy, Black Plastic Body (Includes items 41 thru 47)(Refer to page 18 for
important ordering information)(See item 73)
Faucet Assy, Chrome Body (Includes items 41 thru 48)(See item 73)
03260.0005
29163.0007
29165.0002
00601.0001
37715.0000
29164.0000
00600.0001
2
1
1
1
1
1
1
41
42
43
44
45
46
47
Handle, Faucet
Bonnet, Faucet
Spring Faucet
Collar, Spring (Refer to item 72)
Stem, Faucet
Seat Cup, Faucet (Refer to item 72)
35758.0002*
35206.0000*
1
1
Faucet Body, Black Plastic (Order item 40)
Faucet Body, Chrome (Order item 40)
48
49
38473.0000
1
Insert
- - - - - - - -
37720.0003*
2
2
Tube, Silicone .25" ID x 36.0" (If for first replacement, order item 75)
Tube, Silicone .375" ID x 36.0" (Order item 69)
50
26443.0000
34644.0000
2
2
Reducer, Barb .375" x .25"
Connector, Barb .375" x .375"
For use with .375" BIB adapter
51
52
12422.0001
12
Clamp, Hose .59"/.66"
37720.0000*
38295.0000*
2
2
Tube, Silicone .375" ID x 3.0" (Order item 70)
Tube, Silicone .375" ID x 36.0" (Order item 70)
53
37744.0000
37744.0001
2
2
Tube, Concentrate Bottle .25"
Optional
Tube, Concentrate Bottle .375"
54
55
56
57
34093.0000
38029.1000
03229.0000
03207.0004
1
1
1
1
Lid, Reservoir
Drip Tray Assy (Includes items 56 & 57)
Drip Tray Cover
Drip Tray
(continued)
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.
15
34106.1 112106
TCD-1
TCD-2
REPLACEMENT PARTS (TCD-2)
(continued)
65
66
53
50
51
52
51
Concentrate Bottle Tube
54
.375" BIB Adapter
51
49
Bag Divider
30
59
63
31
33
24
22
10
18
32
34
35
36
19
20
17
26
21
16
15
25
23
19
37
39
29
38
14
13
12
11
10
27
58
41
42
1
5
40
51
28
6
43
44
61
62
7
60
8
9
45
46
48
47
2
3
4
56
57
55
64
63
P3462.60
34106.1 112106
16
REPLACEMENT PARTS (TCD-2)
ITEM
PART NO.
QTY.
DESCRIPTION
58
59
60
61
62
63
64
65
66
00656.0000
38130.0000
38465.0000
38466.0000
00651.0000
38278.0002*
38839.0000
38745.1000
1
1
1
1
1
2
1
1
Decal, Plumbing Code
Decal, Faucet Under Pressure
Decal, Pressure Regulator
Decal, Shut-off
Decal, BUNN
Edging 36.0" (Order item 74)
Stand
Bag Divider (Includes Item 66)
38278.0001*
38278.0003*
1
2
Edging 9.5" (Order item 74)
Edging 1.0" (Order item 74)
67
68
69
00674.0000
M2531.0000
1
1
Brush, Tube .75" (Not illustrated)
Lube&Sealant Compound (Not illustrated)
37721.1000
37721.1001
37721.1002
-
-
-
Tube, Silicone .25" ID x 12.0"
Tube, Silicone .25" ID x 36.0"
Tube, Silicone .25" ID x 120.0"
70
71
37720.1000
37720.1001
37720.1002
-
-
-
Tube, Silicone .375" ID x 12.0"
Tube, Silicone .375" ID x 36.0"
Tube, Silicone .375" ID x 120.0"
37747.1002
37747.1003
-
-
Parts Bag (Includes items 1,5,24,40,51 & 53)(with 3.0" BIB hose)
Parts Bag (Includes items 1,5,40,50,51,52,53 & 55)(with 36.0" BIB hose)
72
73
74
75
38471.0000
28707.0004
38278.1002
39169.0000
-
-
-
-
Kit, Faucet Seat Cup (Includes items 44 & 46)
Kit, Faucet Repair (Includes items 41 & 43-46)
Edging 36.0" (Use as required)
Tube Replacement Kit (Includes items 27,32,49,51-53)(Two Kits required for TCD-2)
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.
17
34106.1 082506
ICED TEA DECAL PLACEMENT
APPROX.
5“
PLASTIC BODY FAUCET COMPARISON
If you have a plastic body faucet of this
design, you must order a complete new
plastic faucet.
New Plastic Faucet Design
34106.1 020306
18
|