Daewoo DWA 122C User Manual

PRECAUTIONS FOR PROPER USE OF AIR CONDITIONER

Please observe the following instructions.

1. Operate the Selector Switch to run or stop the unit.

- Do not use Main Power Switch or Auxiliary Power Switch to operate unit.

2. Do not stick anything into the air outlet or inlet.

- It is dangerous and it can cause injury or damage.

3. Avoid exposing your body directly to a continuous cool air - flow for long periods.

- It is not good for your health.

4. Do not pour water on the unit to clean it.

- It is dangerous and it can cause injury or damage.

Never use solvents or harsh chemicals when cleaning the unit.

When the air inlet grill and cabinet are dirty, wipe with luke - warm water (below 104°F or 40°C)

5. Avoid placing any obstacles near the inlet or outlet.

- If the inlet or outlet is blocked with any obstacle, it may cause damage to the unit.

6. Do not run or stop the unit frequently.

- If you run or stop the unit more then 4-5 times an hour, it can cause damage to the unit.

7. Wait at least 3 minutes before restarting the unit or in the case of power failure.

- If you turn on the unit within 3 minutes after power off, this can cause damage to the unit.

8. If the air conditioner is operated without an air filter, dust is not removed from the air, and resultant

accumulation in the unit may lead to a failure.

- Do not forget to install the air filter.

9. The air filter should be cleaned at least once every two weeks.

10. When the unit is cleaned, set the Selector Switch at off position.

- And then unplug the power plug.

11. Never store gasoline or other flammable liquid near the air conditioner.

- It is very dangerous.

12. Do not force the controls on the front panel too much.

- It can cause damage the controls and the unit.

13. Set a comfortable temperature.

- Very low temperature setting considerably increase power consumption.

14. Be careful to keep room temperature comfortable.

- Avoid continuous direct air flow on you or a sick person while sleeping.

15. Do not remove the plug by pulling the power cord.

- Damage to the cord and may cause shock hazard.

INSTALLATION INSTRUCTIONS

• WINDOW REQUIREMENTS

These instructions are provided for a standard double hung window

or mobile home double hung window installation in windows 27.5

inch (699mm) to 36 in (914mm). The upper and lower sash must

open sufficiently to allow a clear vertical opening of 15 in (381mm)

from the bottom of the sash to the window sill.

27.5" To 36"

14.9" MIN

Select a centrally located window on the side of the room that

receives the least direct sunlight. There should be no obstruction to

air flow either inside(i.e curtains) or outside (i.e fence, wall or

bushes).

15" MIN

Read this entire installation manual thoroughly before beginning the

installation.

Make sure you have the necessary tools and other materials for the

job. Study the illustrations in these instructions to become familiar with important details of the installation

process.

Read the Use & Care manual to become familiar with the operation of your room air conditioner.

IMPORTANT :

It is important, both for your personal safety and to avoid possible damage to your

home, that you observe the safety instructions that are given.

After installing the unit, re-read these instructions to make sure you have completed each step and all parts are

fastened in place for a secure installation.

For best results, perform the installation procedure in the order given. Doing so will minimize the time required

to install the unit.

• BASIC TOOLS NEEDED

• Standard screwdriver

• Carpenter’s level

• Electric drill

• Phillips screwdriver

• 1/4” hex driver

• 1/8” drill bit

• Sharp knife

• Tape measure

• SAFETY INSTRUCTIONS

CAUTION

• The air conditioner shall be installed in accordance with the national wiring regulation.

1. Install an exclusive main power switch (main circuit breaker) or GFI (Ground Fault Interrupted)

switch.

2. Be sure to use grounded power source.

3. Power source for DWC-100C, DWC-100CS, DWC-121C, DWC-121CS is 115V and DWA-122C,

DWA-122CS, DWA-150C, DWA-150CS, DWA-151C, DWA-151CS is 208~230V.

4. Consumer must pay charges for wiring and installation.

• SAFETY INSTRUCTIONS (CONTINUED)

The receptacle should be an individual branch circuit used only for this air conditioner. Be sure the electrical

service is adequate for the model air conditioner you have chosen. The complete electrical rating of your air

conditioner is stated on the name plate located at the unit’s side. Be sure the plug receptacle is close enough

for the power cord to reach it.

WARNING :

An extension cord should not be used with your air conditioner!

To minimize shock and fire hazards, proper grounding is important. For your safety and

protection,this air conditioner is equipped with a special three-prong grounding plug on the service cord.

WARNING :

Do not, under any circumstances, cut or remove the grounding prong on the plug. To do so will create a shock

hazard.

Your air conditioner must be plugged into a properly grounded and polarzied three prong receptacle. Do not

use an adapter plug. If the wall receptacle you intend to use will not accept a three-prong plug, or if you are not

sure the outlet is adequately grounded or protected by a fuse or circuit breaker, have a qualified electrician

install the proper oulet according to the National Electric Code and applicable local code.

• BEFORE INSTALLATION

Test Run Unit : Plug unit into proper power supply outlet.

Refer to operating instructions in this manual for comfortable living. Check all controls for correct

operation, then unplug unit.

Determine Correct Mounting procedure-Refer to Window Installation or Through the Wall Installation.

WARNING :

• Moving parts can cause personal injury. Be careful when test-running unit. Do not operate

unit with front grille removed .

• Be sure to use an exclusive power source.

• Contact service man for replacement of power cord.

• Step 1 - Prepare Components For Installation

Parts for installation are as follows;

• Sill Bracket (2 pieces)

• Window Kit Left side (Frame ‘L+Shutter) - (1 piece)

• Window Kit Right side (Frame ‘R+Shutter) - (1 piece)

• Sash Bracket (1 piece)

• SCREW TYPE

Type A Type B Type C Type D Type E

• DRAIN, DRAIN seal

SHAPE

• Frame Guide Lower - (2 pieces)

• Levelling Screw (Machine M8x45) - (2 pieces)

• 1 inch Screw (M5x30) - (4 pieces)

• 5/8 inch Screw - (M4x16) - (8 pieces)

• DRAIN SCREW (M4x8) - (2 pieces)

• 1/4 inch Screw (M4x6) - (8 pieces)

• Window Seal A, B (2 pieces)

SPEC M8 x 45 M5 x 30 M4 x 16 M4 x 8 M4 x 6

Q'TY

Frame Guide Lower

(2 pieces)

Window

Shutter

(2 pieces)

Window Seal A (1 piece)

Window Seal B (1 piece)

DRAIN Seal

Sill Bracket (2 pieces)

Sash Bracket

DRAIN

(1 piece)

Window kit Frame

Left side (1 piece)

Window kit Frame

Right side (1 piece)

✽✽NOTE: Use Screw

(Type D) only

• Step 2 - Prepare Window For Installation

1. Inspect window track, sash and sill to be sure they are strong enough to hold an air conditioner.

2. Measure width between window frame to be sure instant mount will fit in the window. Instant mount models are

designed for Windows 27.5 inch (699mm) to 36 inch (914mm) wide.

3. Mark the center of Window sill with pencil.

4. Insert Screws (Type A) into the sill bracket.

5. Attach Sill bracket to window sill using two Screws (Type B) by each bracket. The outside edge of window bracket

should be 11.8 inch (300mm) from center line.

6. Adjust Screw (Type A) so that Sill Bracket have a slight tilt by using carpenter's level meter.

Screw Type B

SASH

SILL BRACKET

600mm

300mm

Screw Type A

720~915mm

699~914mm

• Step 3 - Preparation of Chassis

1. Pull the Air-filter out of the Front Grille.

2. Loosen screw which fasten Front Grille with

driver.

3. Pull knobs out of the control.

(when the knobs are too tight to release, leave

them.)

4. Disassemble Front Grille from Chassis.

– Front Grille and chassis are fixed with snap-fit.

1) Release right-lower snap-fit.

– Push the right lower side of chassis to the left, with pushing left side of

Front Grille to the right until the snap-fit is released.

Push

2) Release left-lower snap-fit.

– Push the left-lower side of chassis to the right, with pushing right

side of Front Grille to the right until the snap-fit is released.

Push

3) Pull lower side of the Front Grille until it is separated from the chassis.

(when knobe remain, pull Front Grille until knobs are released from

control)

4) Push base side of the Front Grille to upper side until it is separated

from the chassis.

5) After front grille is removed, remove two screws located in both side of chassis.

6) Grip the handle of base pan and pull out the unit from chassis.

NOTICE: Do not remove any styrofoam because that is a part of the unit.

• Step 4 - Placing Chassis

FRAME

Guide Lower

Screw (Type E, both side)

1. Insert narrow side of ‘Frame Guide Lower’ to rectangle holes

located in bottom of chassis, and fasten it with Screw (Type E).

2. Insert Window Kit Frames to Top Guide and Lower Guide.

3. Fasten Shutter to side holes of Chassis with six Screws (Type E).

4. Place the chassis on the window sill and align it with Sill Bracket

and sill with Lower Frame Guide and locate window sash to Top

Frame Guide. (check the end of chassis for about 1/2 inches

(12mm) distance below the level.)

5. Attach the Window seal B to Frame Guide Top.

6. Fasten Front Chassis Bracket to sill with three Screws

(Type C).

Frame Guide Top

Window Seal B

7. Fasten Sash Bracket with Screw (Type C) to top of

indoor window sash or directly into side of window sash

or directly into side of window frame. This will prevent

raising of the window from the outside. If you have a hard

Screw (Type E)

wood or metal window frame, a 1/8 inch pilot hole may

be needed in order to drive the screws.

8. Attach the Window Seal A to window (see the picture

shown in step 8, page 8)

SASH BRACKET

Screw

(Type C)

Screw (Type C)

• Step 5 - Secure Window Shutter

WINDOW

KIT FRAME

Screw (Type C)

CAUTION Do not drill into window sash until window has

been inspected to make sure drilling or screw will

not damage any locking or lifting mechanism

located in the frame.

WINDOW

SASH

WINDOW

SHUTTER

WINDOW

FRAME

Screw

(Type C)

To provide a proper seal, pull each expandable side Window Shutter

out and up until it is tight against the window frame. Using the hole in

the top and bottom of each Window Kit Frame as a guide, secure

Window Kit Frame in window sash and on the window sill.

INNER WINDOW SILL

• Step 6 - Recheck Installation

To be sure you have correctly installed your Room Air Conditioner, review the steps and make sure all of the

parts are securely fastened in the window as the instructions show. A tight seal is essential.

Read through the Use & Care manual to become familiar with the operation of your room air conditioner.

CAUTION Do not lift window sash without holding the unit. The window sash helps keep the unit in the

window. Exercise caution when opening the window. Failure to do so many result in

personal injury and/or property damage.

• Step 7 - Install Unit and assemble Front Grille

1. Fasten Drain to Base Pan with “Type D” screws. only.

Use of any other longer screw may result in the leakage of

refrigerant and will cause serious damage to the unit.

SEAL DRAIN

DRAIN

Screw (Type D)

2. Push the unit into the installed Chassis.

3. Fasten Base Pan and Chassis with screws to side holes.

CONDENSOR

PAN BASE

4. Assemble Front Grille into Chassis holes.

– Snap Front Grille’s hook to each Chassis holes.

(Be careful the end of ventilation bar is to be located in the gap of blade.)

CAUTION

• When the front grille is reinstalled, the DOOR

VENT should be in position first so that it

would not be bent by grille.

Door Vent

5. Fasten Front Grille with screws.

6. Insert Filter into the Front Grille.

7. Push the Knobs into the control.

• Step 8 - Recheck the entire installation

WINDOW SEAL A

WINDOW SASH

TOP GUIDE

WINDOW KIT FRAME

WINDOW SEAL B

Screw (Type C, 2 pieces)

WINDOW KIT 'R & 'L

Screw (Type E, 2x4=8 pieces)

GUIDE LOWER

Screw (Type C, 2x1=2 pieces)

Screw (Type C, 3 pieces)

SILL

SILL BRACKET(2 pieces)

Leveling Screw (Type A, 2x1= 2 pieces)

OUTER WINDOW SILL

Screw (Type B, 2x2=4 pieces)

WALL

NAMES OF MAJOR COMPONENTS

• DWC-100C / DWC-121C / DWA-122C / DWA-150C / DWA-151C

• DWC-100CS / DWC-121CS / DWA-122CS / DWA-150CS / DWA-151CS

NO PART NAME

AIR FILTER

GRILLE FRONT

CABINET

BLADE HORIZENTAL

AIR VENT

FRAME GUIDE TOP

BLADE VERTICAL

10 FRAME WINDOW KIT

11 SHUTTER WINDOW

KNOB THERMOSTAT

KNOB SELECTOR

AUTO LOUVER S/W (DWC-100CS/DWC-121CS/DWA-122CS/DWA-150CS/DWA-151CS)

OPERATING INSTRUCTIONS

NOTE

• FOR MOST ECONOMICAL USE

1. Properly control the room temperature.

2. Avoid the unit being exposed to direct sunlight. Keep direct sunlight from the room.

3. Do not leave doors and windows open.

• FAN & COOLING CONTROL

The Fan Control Selector Switch has six positions.

Choose one of the speed settings by rotating the fan control Selector Switch to the appropriate position.

CAUTION

When the air conditioner has been performing its cooling operation and is turned “OFF” or set to

the ‘FAN” position, wait at least 3 minutes before resetting to the cooling operation.

OFF

Select this setting for stop all operation of air conditioner

Select this setting for high air circulation without cooling.

Select this setting for quiet air circulation without cooling.

Select this setting for cooling operation with LOW FAN.

Select this setting for cooling operation with MEDIUM FAN.

Select this setting for cooling operation with HIGH FAN.

HIGH FAN

LOW FAN

LOW COOL

MED COOL

HIGH COOL

• TEMPERATURE CONTROL

Choose a temperature settings by rotating the knob of thermostat to the appropriate position

NOTE

Setting the control at the coldest extreme of the temperature range will not cool the room any

faster. Usually the midpoint is a good starting position. If the room temperature is not satisfactory

after a reasonable period of time, adjust the temperature control to a lower or higher setting.

• The Thermostat automatically starts and stops cooling operation in

order to keep the room temperature at a proper level, and this results in

efficient use of power and economical cooling.

• Turn clockwise for a cooler room temperature.

• Turn counter-clockwise for a warmer room temperature.

GENERAL INFORMATION

• CHANGING AIR FLOW DIRECTION

Air flow deflectors divert air from center flow to left or right and up or down.

Adjust deflectors for desired air flow pattern.

AUTO SWING (DWC-100CS, DWC-121CS, DWA-122CS, DWA-150CS, DWA-151CS)

When the auto louver switch is turned to “ON” position, the vertical louvers

automatically move right and left.

AUTO SWING

Thus, you can obtain comfortable cooling.

The vertical louvers may be stopped at any position when the auto louver

switch is turned off.

ON / OFF

• AIR FLOW AROUND UNIT

Check in door grill and outdoor louvers for air flow obstructions. Do not block air flow to and from unit. The

outdoor coil should be checked and periodically cleaned for debris that may collect and block unit air flow.

If air flow is obstructed or deflected back into unit, the compressor may cycle on and off rapidly, causing

early compressor failure.

• DRAIN HOLE AND WATER DRIPPING OUTSIDE

Locate drain hole at the rear or on the bottom of unit. Water in base pan is picked up by the fan blade and

thrown onto the warm outdoor coil where it evaporates. The air conditioner must be installed level or tilted

slightly to the outside for proper water disposal. On exceptionally hot and humid days the air conditioner

may permit excess water to pass thru rear drain hole or overflow. This should be considered normal.

• HOW TO INSTALL THE DRAIN CAP

Install the drain cap like Fig. of the right side.

There are two kinds of method to install the drain cap.

The rear side of the unit

The first method is that the shape of hole like

SEAL DRAIN

It is good for the household.

Drain Cap

The second method is that the shape of hole is like

It is good for the shop.

Screw (Type D)

• DOOR VENT

The door vent for the room air ventilation is lever type.

If the door vent lever moves to the left, then close the

Door Vent

vent and moves to the rght, then open the vent.

✽

Close Vent ✽✽Open

CARE AND MAINTENANCE

CAUTION

To avoid death or personal injury due to electrical shock, turn fan control OFF and unplug power cord

before cleaning or performing maintenance. After cleaning or performing maintenance, reconnect power.

• AIR FILTER

Clean the air filter, which removes dust inside the room.

It should be washed at least once every week during operation.

1. Remove the Air Filter from the front grill by pulling to right.

2. Clean Air Filter with a vacuum cleaner or lukewarm, soapy water.

3. Shake it when clean to remove moisture completely. Reinstall.

NOTE

A dirty Air Filter reduces air flow and the cooling capacity.

Do not operate unit without Air Filter.

• CLEANING THE AIR CONDITIONER

1. At least once a year, remove cabinet and thoroughly clean air

conditioner. Have the unit inspected by an authorized service

man to ensure unit is functioning properly.

2. Wash air conditioner with lukewarm, soapy water as needed.

Rinse and dry thoroghly.

3. If using concentrated liquid detergent, dilute in warm water first.

4. Front grill may be wiped off with a cloth dampened in a mild

detergent solution.

5. Cabinet may be washed with mild soap or detergent and

lukewarm water, then polished with liquid wax for appliances.

6. Condenser and Evaporator coils should be cleaned

at the beginning of each cooling season. Use a soft brush or vacuum

cleaner to clean them, making sure that the Condenser and Evaporator coils are not damaged.

7. Do not use abrasive cleaners. These items scrach, crack and discolor surfaces.

NOTE

To assure continued peak efficiency, condenser coils (weather side of unit) should be checked

periodically and cleaned if clogged with soot or dirt from the atmosphere.

ELECTRICAL REQUIREMENTS

• ELECTRICAL GROUNDING INSTRUCTIONS

This appliance is equipped with a three-prong(grounding) plug for protection against possible shock

hazards. If a two-prong wall receptacle is encountered, the customer is required to contact a qualified

electrician and have the two-prong wall receptacle replaced with a properly grounded three-prong wall

receptacle in accordance with the National Electrical Code.

WARNING :

To avoid death, personal injury or properly damage due to electrical shock, this unit must be grounded.

Do not under any circumstances cut or remove the round grounding prong from the plug.

Do not use a two prong adapter.

• USE OF EXTENSION CORD

Because of potential safety hazards under certain condition, we strongly recommend against the use of an

extension cord. However, if you still elect to use an extension cord, it is absolutely necessary that it will be a UL

listed 3-wire grounding type appliance extension cord rated has a 3-blade grounding plug and a 3-slot receptacle

that will plug into the appliance. The marked rating of the extension cord should be 125V/13A minimum for

DWC-100C, DWC-100CS, DWC-121C, DWC-121CS and 250V/10A minimum for DWA-122C, DWA-122CS,

DWA-150C, DWA-150CS, DWA-151C, DWA-151CS.

WARNING :

To avoid death, personal injury or properly damage due to electrical shock, do not use an

extension cord or pinch the power cord.

Do not remove the warning tag from the power cord.

BEFORE CALLING FOR SERVICE

When you find something wrong with your room air conditioner, please carefully check the following items.

If you are unable to find the cause of trouble, contact your service dealer.

Difficulty

Possible Cause