Headset with Bluetooth® Wireless
Technology
Instruction Manual
JB-TH220
Please read this manual carefully before operating and save it
for future reference.
Have a question? Please visit http://www.jWIN.com
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
USER SAFETY GUIDE
Important Safety Instructions-Continued
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
7. Power sources – The appliance should be connected to a
power supply only of the type described in the operating
instructions or as marked on the appliance.
8. Cleaning – The appliance should be cleaned with a dry cloth.
9. Objects and liquids entry – Care should be taken so that
objects do not fall and liquids are not spilled into the device’s
openings.
10.Servicing – The user should not attempt to service the
appliance beyond that described in the user's operating
instructions. All other servicing should be referred to qualified
service professional.
FCC Notice (USA)
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Refer to 47 CFR Sec. 15.19.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
- 2 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
USER SAFETY GUIDE
FCC Notice (USA)-Continued
communications, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
•
NOTE: Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment. Refer to 47 CFR Sec.
15.21.
Industry Canada Notice to Canadian Users
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation of the device. Refer to IC
RSS 210 Sec. 5.11. The term “IC” before the certification or
registration number only means that the registration was
performed based on a Declaration of Conformity and that
Industry Canada technical specifications were met. It does not
imply that Industry Canada (IC) approved this equipment. Refer
to Self-Marking 6(f) and RSP 100 Sec. 4.
- 3 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
USER SAFETY GUIDE
Additional Safety Instructions
•
When not in use, keep your device in a safe place where it
will not be bent or crushed.
•
Keep this device away from children. Some small and
detachable parts might be swallowed by children and result in
harm to them.
About Electromagnetic Interference (EMI)
This device is designed and manufactured not to exceed the
exposure limit for radio frequency energy, which is set by the
Federal Communications Commission of the U.S government.
The term “EMI” is short for the electromagnetic interference
caused by the electromagnetic field generated by electronic
devices. In fact, most electrical appliances and devices emit
electric and magnetic fields, and most of modern electronic
devices are susceptible to the EMI if they are inadequately
shielded or designed.
•
If you use any personal medical device, such as a pacemaker,
please consult the manufacture of your medical device to
determine if it is adequately shielded from EMI. Your
physician might assist you in obtaining this information.
Please turn off this device if you are instructed to do so,
especially on an airplane or in a hospital.
•
•
Please keep away from medical instruments in a hospital or
medical unit while using this device.
- 4 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
USER SAFETY GUIDE
IMPORTANT NOTES ON HEARING
Your hearing is very important to you and to us. We strongly
recommend you to follow the guideline below in order to prevent
possible damage to or loss of hearing.
Hearing experts caution that listening to loud sounds can
damage hearing over time. With continuous listening to loud
sounds, hearing adapts and will give the impression that volume
has reduced. What seems normal may, in fact, be harmful. To
guard against this before hearing adapts, set the volume at a low
level and slowly increase the volume level until sound can be
heard comfortably and clearly without distortion. Damage to
hearing is accumulative and is irreversible. Ringing or discomfort
in the ears indicates that the volume is too loud. Once a
comfortable listening level has been established, do not increase
the volume level further.
CAUTION!
If you experience a ringing sound in your ear, lower the volume
or discontinue the use of this product.
- 5 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
TABLE OF CONTENTS
GETTING STARTED
Introduction. …..………..………………………………………
What’s Included in the Package…………………………..…
What is Bluetooth wireless technology? .............................
8
8
9
Location of Controls…………………………………………… 10
Charging the Headset………………………………………… 10
Turning on the Headset………………………………………. 11
Turning off the Headset………………………………………. 11
Pairing the Headset using Bluetooth Wireless Technology. 12
OPERATING INSTRUCTIONS
Making a call…………………………………………………… 14
Answering a call……………………………………………… 15
Ending a call…………………………………………………… 15
Rejecting an Incoming Call…………………………………… 16
Transferring Calls between Devices………………………… 16
Adjusting the Volume…………………………….
16
TROUBLESHOOTING GUIDE
Questions and answers about the product………………… 17
SPECIFICATIONS
Technical information about the product…………………… 17
- 6 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
GETTING STARTED
Headset with Bluetooth Wireless Technology
Thank you for purchasing the JB-TH220. This headset has been
designed wireless mobile phone connection using Bluetooth
wireless technology. Please keep this manual in a safe place for
future reference.
•
•
•
•
•
•
Answer mobile phone calls hands free
Supports the headset (HSP), hands-free (HFP) profiles
Standby time up to 170 hours
Continuous talking time up to 6 hours
Communication range up to 33ft
Compliant with Bluetooth wireless technology V2.0 and EDR
What’s included in the package?
•
•
•
•
•
Headset
Charger
USB charging cable
Instruction manual
Warranty card
- 8 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
GETTING STARTED
What is Bluetooth wireless technology?
Bluetooth wireless technology is a short-range wireless
communication technology intended to replace the cables
connecting electronic devices while maintaining the high level of
security. With Bluetooth wireless technology, two devices can be
connected at the same time without the need to face each other
or the concern of interference from other wireless communication
within its optimum range of 33 feet.
Through a process called “Pairing,” two or more devices with
Bluetooth wireless technology can interact with each other
without interference from other wireless platforms nearby,
including other Bluetooth wireless communications between
unrelated devices.
- 9 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
GETTING STARTED
LOCATION OF CONTROLS
1. Multi-function button 5. Ear clip
2. Volume +/- button
3. Microphone
6. Earpiece/receiver
7. LED indicator
4. Charging port
Charging the Headset
Fully charge the headset by connecting the
charger to the mini-USB port on the top of the
headset. The red indicator will light up when
charging. Once fully charged, the red indicator
will go out.
TOP
- 10 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
GETTING STARTED
Turning on the Headset
Press and hold the Multi-function button for approximately three
(3) seconds until the blue indicator light begins flashing.
Note: The blue indicator will continuously flash when the power
is on.
Turning off the Headset
Press and hold the Multi-function button for approximately five
(5) seconds until the red indicator flashes briefly.
Note: No light will flash when the power is off.
- 11 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
GETTING STARTED
Pairing the headset with mobile phones
using Bluetooth wireless technology
1. With the power turned off, press and hold the Multi-function
button for approximately 3 to 5 seconds. Blue and Red lights
will blink alternatively.
2. Set both the JB-TH220 and the mobile phone to SEARCH
mode following the pairing instructions included with the
phone, placing both units close together. Typically mobile
phones have a Bluetooth menu from which SEARCH can be
selected.
3. The mobile phone with Bluetooth wireless
technology will identify the Headset.
4. Confirm with “yes,” or “ok.”
5. When asked for a passkey
or PIN, enter 0000 (4
zeros) and press “yes,” or “ok.”
6. Phone and headset have successfully paired.
- 12 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
GETTING STARTED
Notes on Pairing
This headset will not be recognized by your mobile phone unless
it is properly paired. The JB-TH220 cannot pair with mobile
phones which are not equipped with Bluetooth wireless
technology. To ensure that correct pairing is accomplished, it is
important to follow both these instructions and those which
accompany the corresponding mobile phone.
Wearing the Headset
The JB-TH220 can be worn on either the left of right ear.
1. Place the ear hook over the right ear
with earpiece in the ear.
2. For placement in the left ear, lift the
ear hook as shown.
3. Rotate the ear hook on the swivel.
4. The JB-TH220 can now be worn
comfortably on the left ear.
- 13 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
OPERATING INSTRUCTIONS
Making a Call
This headset must also be paired with your phone, enabled by
Bluetooth wireless technology in order to make a call.
1. Normal dialing:
a. Dial the telephone number on your mobile phone.
b. When the call connects, it will be heard through the
headset.
2. Last number redial: After a call has been made, the number
can be redialed by short-pressing the Multi-function button
two (2) times.
3. Voice dial function: If your mobile phone supports voice
dialing, set up voice tags using the instructions for your
phone. For the best connection with JB-TH220, pair and use
this unit when establishing voice tags.
a. Press and hold the Multi-
function button for
approximately three (3)
seconds.
b. Say the name of the person
you wish to call.
c. The number of the selected
person will dial and be
connected.
Touch
- 14 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
OPERATING INSTRUCTIONS
Answering a Call
Be certain the headset is properly paired with a mobile phone
featuring Bluetooth wireless technology before answering a call.
1. An incoming phone call will be indicated by a ring. Press the
Multi-function button once to answer the call.
2. If the headset is off when there is an incoming call, press the
Multi-function button to turn on the headset and answer the
call as usual.
Notes on Answering a Call
•
When there is an incoming call, some phones might not ring
when paired with JB-TH220, but there will be a beeping
sound from the headset. Press the Multi-function button to
answer the phone when you hear this beep.
•
Similarly, some phones may not send an incoming call signal
to the headset. Press the Multi-function button when the
phone rings.
Ending a Call
There are several ways to end a phone call.
1. Press the Multi-function button on the headset.
2. Press the End key on the mobile phone.
3. A call will also end as the person on the other end hangs up.
Note: Your mobile phone with Bluetooth wireless technology
must be paired with the JB-TH220 BEFORE these functions are
attempted.
- 15 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
OPERATING INSTRUCTIONS
Rejecting an Incoming Call
When there is an incoming call, press and hold the Multi-
function button for approximately 3 to 5 seconds and release to
reject the call.
Transferring Calls between Devices
1. To transfer a current call to your mobile phone when using
the JB-TH220, press the Multi-function button for three (3)
seconds. The call will no longer be communicated through
the JB-TH220. Use your mobile phone as normal.
2. To transfer a current call to the JB-TH220 when using your
mobile phone, press the Multi-function button for 3 seconds.
The call will now be communicated through the headset.
Adjusting the Volume
1. To adjust the volume, press the Volume Up (S) or Volume
Down (T) button.
2. Press and hold the Volume Up (S) or Volume Down (T)
buttons to adjust the sound level continuously
- 16 -
Headset w/ Bluetooth technology
V10M10_IM_EN_08032007
TROUBLESHOOTING GUIDE
1. The headset does not work with my mobile phone.
Be certain that your mobile phone is equipped with Bluetooth
wireless technology. This headset will only work with such
mobile phones. Additionally, your mobile phone must be
paired with the headset BEFORE all other pairing.
2. There is interference on the headset with my phone.
The maximum distance for Bluetooth wireless communication
is 33 feet (10 meters). When this distance is approached,
background noise will increase. Also, a poor signal on the
mobile phone may contribute to degradation the quality of
sound as well.
3. There is no sound.
Ensure that both the mobile phone and the JB-TH220 are
turned on, set up, and paired correctly. Be certain that the
volume is turned up on both devices.
Specifications
•
•
•
•
•
•
Bluetooth spec. v2.0+EDR compliance
Headset (HSP) and Hands-free Profile (HFP) supported
Bluetooth Class ll
Typically 6 hrs Talk Time
Typically 170 hrs Stand-by Time
Rechargeable Lithium Polymer Battery
- 17 -
TEL: 516-626-7188
FAX: 516-626-7105
© 2007 jWIN Electronics Corp. All rights reserved. The Bluetooth word mark
and logos are owned by Bluetooth SIG, Inc. and any use of such marks by
jWIN Electronics Corp. is under license. No portion of this printed material or
product enclosed herewith including design, shape and graphics, may be
reproduced or transmitted in any form without the expressed written consent
of jWIN Electronics Corp. by any means, electronic or mechanical, including
photocopying, recording or the use of an information storage and retrieval
system. Any unauthorized distribution or reproduction of this printed material
or product, or any portion thereof, will be prosecuted to the fullest possible
extent of the law. Mobile phone not included in this package
Printed in China
|