4-283-582-11 (2)
Data
Projector
Operating Instructions
Before operating the unit, please read this manual and supplied Quick Reference Manual
thoroughly and retain it for future reference.
VPL-SX125
VPL-SW125
Not all models are available in all countries and area. Please check
with your local Sony Authorized Dealer.
© 2011 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
B Overview
Location and Function of Controls
Main unit
2
7
1
8
9
qs
qd
qf
0
6
5
qa
qa
qa
g LAMP/COVER indicator
j Remote control detector
l Speaker
4
3
m Security lock
Connects to an optional security cable
manufactured by Kensington.
a Projection lens
For details, visit Kensington’s web site.
n Security bar
Connects to a commercially available
security chain or wire.
Ventilation holes (intake)
If it is difficult to pull out, pull out the
Security bar using a screwdriver.
e Ventilation holes (intake)
f Ventilation holes (exhaust)
Caution
Do not place anything near the ventilation
holes as this may cause internal heat
buildup. Do not place your hand near the
ventilation holes and the circumference as
this may cause injury.
Security bar
Location and Function of Controls
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Panel
VPL-SX125
4
2
6
8 7
1
5
9
VPL-SW125
4
6
3
8 7
1
5
9
Input (pages 7, 8)
Output (page 10)
a INPUT A
f OUTPUT
Video: RGB/YPBPR input connector
(RGB/YPBPR)
Audio: Audio input connector (AUDIO)
Video: Monitor output connector
(MONITOR)
Audio: Audio output connector
(AUDIO)
b INPUT B (VPL-SX125 only)
Video: RGB input connector (RGB)
Audio: Audio input connector (AUDIO)
Note
This connector outputs the projected image or
audio. The image is output as a computer signal
input from the RGB input connector (INPUT
A/INPUT B (INPUT B is available only for
VPL-SX125)) or a video signal input from the
YPBPR input connector (INPUT A).
c INPUT B (VPL-SW125 only)
Video: HDMI input connector (HDMI)
Audio: HDMI input connector (HDMI)
d S VIDEO (S VIDEO IN)
Video: S video input connector
Audio: Audio input connector (L
[MONO] AUDIO/R)
Others
g RS-232C connector
RS-232C compatible control connector.
Connects the computer’s RS-232C
connector and the RS-232C cross cables.
e VIDEO (VIDEO IN)
Video: Video input connector
Audio: Audio input connector (L
[MONO] AUDIO/R)
Note
i AC IN (∼) socket
The audio inputs of S VIDEO and VIDEO are
shared.
Connects the supplied AC power cord.
4
Location and Function of Controls
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Commander and Control Panel
Remote Commander
a Turning on the power/Going to
standby mode
?/1 (On/Standby) key
7
4
2
1
6
b Selecting an input signal
INPUT
MENU
APA
ECO MODE
RESET
INPUT key
3
4
MENU key
ENTER
RETURN
RESET key
PATTERN
ASPECT KEYSTONE
ENTER /V/v/B/b (arrow) keys
RETURN key
This function is not provided in this
projector.
PIC MUTING
5
D
ZOOM VOLUME
FREEZE AUDIO MUTING
ASPECT key
Control Panel
KEYSTONE key
PATTERN key
This function is not provided in this
projector.
1 2 3
3
6
*
APA (Auto Pixel Alignment) key
Note
* Use this key when inputting a computer
signal via the RGB input connector
(INPUT A/INPUT B (INPUT B is
available only for VPL-SX125)).
e Using various functions during
projecting
*1
D ZOOM (Digital Zoom) +/– key
Enlarges a portion of the image while
projecting.
1 Press the D ZOOM + key to display
the digital zoom icon on the projected
image.
2 Press the V/v/B/b keys to move the
digital zoom icon to the point on the
image you wish to enlarge.
3 Press the D ZOOM + key or the D
ZOOM – key repeatedly to change the
enlargement ratio. The image can be
enlarged up to 4 times.
Press the RESET key to restore the
previous image.
Location and Function of Controls
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PIC MUTING key
Cuts off the image. Press again to restore
the image.
3 Select “User” then press the b key.
The setting items appear.
User
AUDIO MUTING key
Mutes the audio output. Press again to
restore the previous volume.
Lamp Mode
Power Saving Mode Off
Standby Mode Low
Standard
VOLUME +/– key
For adjusting the volume output.
Sel:
Set:
Exit:
*2
FREEZE key
4 Press the V/v key to select the item
then press the ENTER key.
5 Press the V/v key to select the setting
value.
6 Press the ENTER key to restore the
User screen.
Pauses a projected image. Press again to
restore the image.
Notes
*1: Use this key when inputting a
computer signal. But it may not be
used depending on the resolution of
the input signal.
*2: Use this key when inputting a
computer signal.
For details on ECO Mode settings, see
SETTING menu and “Power Saving
Mode” (page 21) on the SET SETTING
menu.
f Setting the energy–saving mode
easily
Others
ECO MODE key
g Infrared transmitter
Energy-saving mode can be set easily.
Energy-saving mode consists of “Lamp
Mode,” “Power Saving Mode” and
“Standby Mode.”
About Remote Commander operation
• Direct the Remote Commander toward the
remote control detector.
1 Press the ECO MODE key to display
the ECO Mode menu.
• The shorter the distance between the
Remote Commander and the projector is,
the wider the angle within which the
Remote Commander can control the
projector becomes.
• Make sure that nothing obstructs the
infrared beam between the Remote
Commander and the remote control
detector on the projector.
ECO Mode Menu
ECO Mode
ECO
User
Sel:
Exit:
2 Press the V/v key or ECO MODE key
to select ECO or User mode.
ECO: Sets each mode to the optimum
energy-saving value.
Lamp Mode: Low
Power Saving Mode: Standby
Standby Mode: Low
(go to step 6)
User: Sets each item of the energy-
saving mode menu as you desire
(go to step 3).
6
Location and Function of Controls
Download from Www.Somanuals.com. All Manuals Search And Download.
B Preparation
Connecting the Projector
Notes
• Make sure all the equipment is powered off when connecting the projector.
• Use the proper cables for each connection.
• Insert the cable plugs firmly; Loose connections may reduce performance of picture signals or
cause a malfunction. When pulling out a cable, be sure to grip it by the plug, not the cable itself.
• For more information, refer also to the instruction manuals of the equipment you are connecting.
• Use a no-resistance audio cable.
Connecting a Computer
Connection with a computer is explained for each input signal.
INPUT A/INPUT B (INPUT B is available only for VPL-SX125)
For connecting a computer with an RGB output connector.
Mini D-sub 15-pin cable (supplied)
RGB output
connector
Computer
Audio output
connector
Audio cable (Stereo mini plug) (not supplied)
Note
It is recommended that you set the resolution of your computer to 1024 × 768 pixels (VPL-SX125)
or 1280 × 800 pixels (VPL-SW125) for the external monitor.
Connecting the Projector
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Video equipment
Connections with a VHS video deck, DVD player, or BD player are explained for each input
signal.
S VIDEO IN
For connecting video equipment with an S-video output connector.
S video cable
(not supplied)
S video output
connector
Audio output
connector
Video equipment
Audio cable (Phono plug × 2) (not supplied)
VIDEO IN
For connecting video equipment with a video output connector.
Video cable (not supplied)
Video output
connector
Audio output
connector
Video equipment
Audio cable (Phono plug × 2) (not supplied)
INPUT A
For connecting video equipment with a YPBPR output connector.
Component – Mini D-sub 15-pin cable (not supplied)
YPBPR output
connector
Audio output
connector
Video equipment
Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)
8
Connecting the Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT B (VPL-SW125 only)
For connecting video equipment with an HDMI output connector.
DVI-D output
HDMI-DVI-D cable
connector
(not supplied)
Computer
HDMI cable
HDMI output
(not supplied)
connector
Video equipment
Notes
• Use HDMI-compatible equipment and cable(s) that have an HDMI logo on them.
• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal
or CEC (Consumer Electronics Control) Signal.
Connecting the Projector
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an External Monitor and Audio Equipment
OUTPUT
Projected images and input audio can be output to display equipment such as a monitor and
audio equipment such as speakers with a built-in amplifier. When an audio cable is connected
to the audio output connector, no sound will be heard from the built-in speaker.
Display equipment
Mini D-sub 15-pin
RGB input
cable (supplied)
connector
Audio input
connector
Audio cable
(stereo mini plug)
(not supplied)
Audio equipment
Note
Projected images and audio can be output. The image is output only as a computer signal input from
the RGB input connector (INPUT A/INPUT B (INPUT B is available only for VPL-SX125)) or a
video signal input from the YPBPR input connector (INPUT A).
10 Connecting the Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
B Projecting/Adjusting an Image
Projecting an Image
The size of a projected image depends on the distance between the projector and screen. Install
the projector so that the projected image fits the screen size. For details on projection distances
5
3
5
4
6
Computer
2
Video equipment
Projector
1
Wall outlet
1 Plug the AC power cord into the wall
6 Switch your computer to output to
external display by changing your
computer’s setting.
outlet.
2 Connect all equipment to the projector
How to switch the computer to output to
the projector varies, depending on the
type of computer.
3 Press ?/1 to turn on the unit.
4 Turn on the connected equipment.
5 Select the input source.
(Example)
+
7 Adjust the focus and position of the
Each time you press the INPUT key on
the projector, the input signal switches.
Press the INPUT key repeatedly to select
an image to be projected.
Projecting an Image 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected image
Focus
Position
Adjuster adjustment button
Adjusting the tilt of the projector with the adjusters
You can adjust the height of the projector
using the adjusters.
By changing the slope of the projector with
adjusters, you can adjust the position of the
projected image.
Notes
• Be careful not to let the projector down on your fingers.
• Do not push hard on the top of the projector with the adjuster extended. It may cause malfunction.
12 Projecting an Image
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the aspect ratio of the projected image
Press ASPECT on the remote commander to change the aspect ratio of the projected image.
Correcting trapezoidal distortion of the projected image (Keystone feature)
Keystone feature may not work automatically when the screen is tilted. In this case, set
keystone manually.
1 Press KEYSTONE on the remote
commander or select V Keystone in the
INSTALL SETTING menu.
2 Use V/v/B/b to set the value. The higher
the setting, narrower the top of the
projected image. The lower the setting, the
narrower the bottom.
Increase the number
towards plus
Note
Since the Keystone adjustment is an electronic
correction, the image may be deteriorated.
Increase the number
towards minus
Automatically adjusts Phase, Pitch and Shift of projected image while a
signal is input from a computer (APA (Auto Pixel Alignment))
Press APA on the remote commander. Press again to cancel during the setting.
Projecting an Image 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning Off the Power
1 Press the ?/1 key on the main unit or the Remote Commander.
The message appears. Press it again according to the message.
2 Unplug the AC power cord from the wall outlet.
After step 1, the fan continues to run for a while to reduce internal heat, however, you may
also unplug the AC power cord before the fan stops.
To clear the confirmation message
The message disappears if you press any key other than the ?/1 key on the main unit or the
Remote Commander, or if you do not press any key for a while.
To turn off without displaying confirmation message
Hold the ?/1 key on the main unit pressed for a few seconds.
14 Projecting an Image
Download from Www.Somanuals.com. All Manuals Search And Download.
B Adjustments and Settings Using a Menu
Using a MENU
Note
The menu displays used for the explanation below may be different depending on the model you are
using.
factory preset value, press the RESET
key during setting or adjusting.
1 Press the MENU key to display the
menu.
Selecting items
2 Select the setting menu.
PICTURE SETTING
Input-A
Use the V or v key to select the setting
Picture Mode
Adjust Picture...
Dynamic
Standard
Game
menu then press b or ENTER key.
Volume
Living
Setting menu
Cinema
Presentation
PICTURE SETTING
Input-A
Presentation
Picture Mode
Adjust Picture...
Volume
30
Sel:
Set:
Back:
Eixt:
Using the setting menu
Press the V or v key to select the item.
Press the ENTER key to restore the
previous screen.
Sel:
Set:
Back:
Eixt:
Using the adjustment menu
To increase the number, press the V or b
key and to decrease the number, press
the v or B key. Press the ENTER key to
register the setting. The previous screen
is restored.
3 Select the setting item.
Use the V or v key to select the setting
menu then press b or ENTER key.
To return to the selection screen of the
setting menu, press the B key.
Setting items
90
PICTURE SETTING
Input-A
Presentation
Picture Mode
Adjust Picture...
5 Press the MENU key to clear the
Volume
30
menu.
The menu disappears automatically if no
key is pressed for a while.
Sel:
Set:
Back:
Eixt:
4 Make the setting or adjustment for the
selected item.
Menu operation differs depending on the
setting item. If the next menu window is
displayed, select the item according to
the operations in step 3.
To return to the selection screen of the
setting items, press the B key. Also, to
reset the setting value of an item to its
Using a MENU 15
Download from Www.Somanuals.com. All Manuals Search And Download.
The PICTURE SETTING Menu
For adjusting the picture for each input signal.
Items
Item descriptions
Picture Mode
Dynamic: Emphasizes the contrast to produce a “dynamic and vivid” picture.
Standard: Makes the picture be natural and well balanced.
Game: Select for viewing game picture.
Living: Select for viewing sports, music, and digital video camera picture.
Cinema: Select for viewing film-like picture.
*1
Presentation : Makes the picture bright to suit for a presentation.
Adjust Picture... The unit can store the setting values of the following sub menu items for each
picture mode separately.
Contrast
The higher the setting, the greater the contrast. The lower the setting, the lower
the contrast.
Brightness The higher the setting, the brighter the picture. The lower the setting, the darker
the picture.
*2 *4
Color
The higher the setting, the greater the intensity. The lower the setting, the lower
the intensity.
*2 *4 *5
Hue
The higher the setting, the more greenish the picture becomes. The lower the
setting, the more reddish the picture becomes.
*2
Sharpness
Color
The higher the setting, the sharper the picture. The lower the setting, the softer
the picture.
High/Middle/Low: The higher the temperature, the more bluish the picture.
The lower the temperature, the more reddish the picture.
*3
Temp.
DDE
(Dynamic
Detail
Off: Plays back the interlace format without conversion.
Progressive: Plays back the video signal of the interlace format converting to
progressive.
Film: Precisely reproduces the image from a film source to suit the original
film source.
Enhancer)
*6
Gamma
Mode
Graphics: Improves the reproduction of halftones. Photos can be reproduced
in natural tones.
*1
Text: Contrasts black and white. Suitable for images that contain lots of text.
Volume
The higher the setting, the higher an audio volume and the lower the setting, the
lower the audio volume. The audio output level will work simultaneously.
Notes
*1: When a computer signal is input, this option is available.
*2: When a video signal is input, this option is available.
*3: When “Picture Mode” is set to the item other than “Presentation,” this option is available.
*4: When a B & W signal is input, this option is not available.
*5: When an analog TV signal is input, this option may not available, depending on the color system.
*6: When a progressive signal or a 1080i signal is input, this option is not available.
16 The PICTURE SETTING Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
The INPUT SETTING Menu
For adjusting the size, position, and aspect ratio of the projected image for each input signal.
Items
Item descriptions
Adjust Signal
Adjusts the image of computer signal. Use this item if the edge of the image
is cut and reception is bad.
*1
Dot Phase
Adjusts the dot phase of the display pixel and the input signal. Set to the
value where looks clearest.
*1
H Size
The higher the setting, the wider the horizontal image elements (pitch). The
lower the setting, the narrower the horizontal image elements (pitch).
*2
Shift
H: The higher the setting, the farther right the image is projected on the
screen. The lower the setting, the image farther left.
V: The higher the setting, the farther up the image is projected on the screen.
The lower the setting, the image farther down.
*3
Aspect
When the
computer
signal is
input
Normal: Displays the image on the center point of the projected image
without changing the resolution of the input signal or enlarging the image.
Full1: Displays the image to fit the maximum projected image size without
changing the aspect ratio of the input signal.
Full2: Displays the image to fit the maximum projected image size.
*4
Full3 : Displays a 1280 × 760 dot picture on the screen without changing
the aspect ratio of the original image.
When the
video signal aspect ratio fixed to 4:3.
4:3: Displays the image to fit the maximum projected image size with an
is input
(VPL-
SX125)
16:9: Displays the image to fit the maximum projected image size with an
aspect ratio fixed to 16:9.
Zoom: Display the center point of the projected image to zoom.
When the
Normal: Displays the image with an aspect ratio fixed to 4:3.
video signal Full: Displays the image with an aspect ratio fixed to 16:9.
is input
(VPL-
SW125)
Zoom: Displays the image to enlarge without changing the aspect
ratio of the original image.
Wide Zoom: Displays the image to enlarge with minimum distortion.
*4 *5
Over Scan
On/Off: When set to “On”, the outer edges of the picture will be hidden.
Select this setting when noise appears along the edge of the picture.
Notes
*1: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B
(INPUT B is available only for VPL-SX125)).
*2: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B
(INPUT B is available only for VPL-SX125)) or a video signal is input from the YPBPR input
connector (INPUT A).
*3: • Note that if the projector is used for profit or for public viewing, modifying the original picture
by switching to the aspect mode may constitute an infringement of the rights of authors or
producers, which are legally protected.
• Depending on the input signal, setting items for aspect ratio or some other setting items cannot
be set in some cases, or changing the aspect ratio setting may have no effect.
The INPUT SETTING Menu 17
Download from Www.Somanuals.com. All Manuals Search And Download.
• A part of the image may be displayed in black, depending on the setting item.
*4: VPL-SW125 only.
*5: Available when a video signal is input from the YPBPR input connector (INPUT A) or the HDMI
input connector (INPUT B). (Available for VPL-SW125 only.)
18 The INPUT SETTING Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Aspect
*1: If you select “Normal,” the image is
projected in the same resolution as the
input signal without changing the aspect
ratio of the original image.
VPL-SX125
Input signal
Recommended
setting value and
projected image
*1
(4:3)
(16:9)
(16:10)
(Full1)
*2: If you select “Full2,” the image is projected
to fit the projected image size, regardless
of the aspect ratio of the image.
*1 *2
(Full1)
*3: Depending on the input signal, the
projected image may be projected as
illustrated below. In this a case, select
“16:9.”
*1 *2
(Full1)
*3
(4:3)
(4:3)
*4: Depending on the input signal, the image
may be projected as illustrated below. In
this a case, select “Zoom.”
*4
(16:9)
(16:9)
The INPUT SETTING Menu 19
Download from Www.Somanuals.com. All Manuals Search And Download.
*1: If you select “Normal,” the image is
projected in the same resolution as the
input signal without changing the aspect
ratio of the original image.
VPL-SW125
Input signal
Recommended
setting value and
projected image
*1 *2 *3
(4:3)
(16:9)
(16:10)
(Full1)
*2: If you select “Full2,” the image is projected
to fit the projected image size, regardless
of the aspect ratio of the image.
*1 *2 *3
(Full1)
*3: If you adjust the projected image position
using an image with 16:9 aspect ratio and
then switch the input source to 4:3 image,
the top and bottom edge of the image may
be hidden. In this a case, select “Full3.”
*3
(Full1)
*4 *5
(4:3)
(Normal)
*4: Depending on the input signal, the
projected image may be projected as
illustrated below. In this a case, select
“Full.”
(16:9)
(Full)
*5: Depending on the input signal, the image
may be projected as illustrated below. In
this a case, select “Zoom.”
20 The INPUT SETTING Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
The SET SETTING Menu
The SET SETTING menu is used for setting various functions of the projector.
Items
Item descriptions
Smart APA
On/Off: When set to “On,” executes APA automatically when a signal
*1 *2
is input.
Auto Input Search
Input-A Signal Sel.
Color System
On/Off: When set to “On,” the projector detects input signals in the
following order: Input-A/Input-B/Video/S Video. It indicates the input
channel when the power is turned on or the INPUT key is pressed.
Auto/Computer/Component/Video GBR: When set to “Auto,”
selects the type of video signal input automatically when “Input-A” is
*3
selected with the INPUT key.
Auto/NTSC3.58/PAL/PAL-60/SECAM/NTSC4.43/PAL-M/PAL-N:
When set to “Auto,” selects the color system automatically when “S
*3
Video” or “Video” is selected with the INPUT key.
Power Saving Mode
Lamp Cutoff: The lamp turns off automatically and power
consumption is reduced if no signal is input for 10 minutes. The lamp
lights again when a signal is input or any key is pressed. In Lamp
Standby: The power will be turned off automatically and the projector
goes to Standby mode if no signal is input for 10 minutes.
Off: The Power Saving Mode is canceled.
Panel Key Lock
On/Off: When set to “On,” locks all the control panel keys of the
projector. However, you can operate the following when set to “On”:
• Press and hold the ?/1 key for approximately 10 seconds during
Standby mode.
c The projector turns on.
• Press and hold the ?/1 key for approximately 10 seconds during
power on.
c The projector goes to Standby mode.
• Press and hold the MENU key for approximately 10 seconds during
power on.
c “Panel Key Lock” is set to “Off” and enables operation of all keys
on the projector.
CC Display
CC1/CC2/CC3/CC4/Text1/Text2/Text3/Text4: Select the closed
caption service (Captions or Text).
Off: Closed caption does not appear.
*4
Network Setting
IP Address Setup
Auto (DHCP): The IP address is assigned automatically from the
DHCP server such as a router.
Manual: To specify the IP Address manually.
IP Address/Subnet When “Manual” is selected for “IP Address Setup,” select the item
Mask/Default
Gateway/DNS
Server/Apply
with the B or b key and input the value with V or v key. When all
items are entered, select “Apply” then press the ENTER key. The
entered settings will be registered.
Lamp Timer Reset
The SET SETTING Menu 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
*1: Executes APA when a computer signal is input via the RGB input connector (INPUT A/INPUT
B (INPUT B is available only for VPL-SX125)).
*2: If the projected image includes large amount of black portion around it, the APA function will
not work properly and a part of the image may not be displayed on the screen and also optimum
image cannot be obtained, depending on the type of input signal. In this case, adjust the “Dot
Phase,” “H size,” and “Shift” items manually.
*3: The image may not be adjusted properly depending on the type of input signal. In such a case,
adjust it manually to suit to the connected equipment.
*4: “Network Setting” is not displayed while “REMOTE” is selected from “External Control” in the
INSTALL SETTING menu.
22 The SET SETTING Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
The MENU SETTING Menu
The MENU SETTING menu is used for setting for the operations by using the menu or the
Remote Commander.
Items
Item descriptions
Status
On: All on-screen statuses are enabled.
Off: Turn off the on-screen displays except for the menus, message when
turning off the power, and warning messages.
Language
Selects the language used in the menu and on-screen displays.
Menu Position
Top Left/Bottom Left/Center/Top Right/Bottom Right: Selects the display
position of the menu.
Start Up Image
On/Off: When set to “On,” the Start Up Image is displayed on the screen upon
startup of the projector.
The MENU SETTING Menu 23
Download from Www.Somanuals.com. All Manuals Search And Download.
The INSTALL SETTING Menu
The INSTALL SETTING menu is used for installing the projector.
Items
Item descriptions
*1
V Keystone
Auto: Set keystone adjustment automatically. When the projector is
installed on an uneven surface, the feature may not work properly. In this
case, select “Manual” to set keystone adjustment manually.
Manual: The higher the setting, narrower the top of the projected image.
The lower the setting, narrower the bottom of the projected image.
Image Flip
HV/H/V/Off: Flips the projected image horizontally and/or vertically
according to the installation method.
Background
Lamp Mode
High Altitude
Black/Blue: Selects the background color of the projected image when no
signal is input.
High/Standard/Low: When set to “High,” the image becomes brighter,
and power consumption becomes higher.
On/Off: Set to “On” when using the projector at an altitude of 1,500 m or
higher. Continuing to use the wrong setting may affect component
reliability.
*2
Mode
*3
Security Lock
On/Off: This function enables restriction of the projector to authorized
users by password. The setting procedures for security locking are as
follows:
1 Select “On” and press ENTER to display the setting menu.
2 Input the password with the MENU, V/v/B/b, and ENTER keys. (The
default password setting is “ENTER, ENTER, ENTER, ENTER.”)
3 Input a new password with the MENU, V/v/B/b, and ENTER keys.
4 Enter the password again to confirm.
Enter the password when you turn on the projector after disconnecting and
reconnecting the AC power cord.
When it is set to “Off,” you can cancel the security lock. You are required to
input the password again.
If you fail to enter the correct password after three consecutive times, the
projector cannot be used. In this case, press the ?/1 key to go Standby
mode then turn on the power again.
Direct Power On
External Control
On/Off: When set to “On,” you can turn the power on without going to
Standby mode when the AC power cord is connected to a wall outlet.
Regardless of the Direct Power On setting, you can disconnect the AC
power cord to turn off the power without going to the Standby mode.
REMOTE: Select to control the projector using RS-232C.
NETWORK: Select to control the projector via network.
*4
Standby Mode
Standard/Low: When set to “Low,” lowers power consumption in Standby
mode.
Notes
*1: Since the Keystone adjustment is an electronic correction, the image may be deteriorated.
*2: When “High Altitude Mode” is set to “On,” the speed of the fan increases, and the fan noise
becomes slightly louder.
*3: You will not be able to use the projector if you forget your password. If you call qualified Sony
personnel because you have forgotten the password, you will be asked to verify the projector’s
24 The INSTALL SETTING Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
serial number and your identity. (This process may differ in other countries/regions.) Once your
identity has been confirmed, we will provide you with the password.
*4: When “Standby Mode” is set to “Low,” the network and network control function cannot be
operated while the projector is in standby mode.
The INSTALL SETTING Menu 25
Download from Www.Somanuals.com. All Manuals Search And Download.
The INFORMATION Menu
The INFORMATION menu enables you to confirm various information on the projector, such
as the total usage hours of a lamp.
Items
Item descriptions
Model Name
Displays the model name.
Serial No.
Displays the serial number.
*1
fH
Displays the horizontal frequency of the current input signal.
Displays the vertical frequency of the current input signal.
Displays the type of the current input signal.
Indicates the total usage time of a lamp.
*1
fV
Signal type
Lamp Timer
Note
*1: These items may not be displayed depending on the input signal.
26 The INFORMATION Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
B Network
Using Network Features
Connection to the network allows you to operate the following features:
• Checking the current status of the projector via a Web browser.
• Remotely controlling the projector via a Web browser.
• Receiving the e-mail report for the projector.
• Making the network settings for the projector.
• Supports network monitoring, control protocol (Advertisement, PJ Talk, PJ Link, AMX
DDDP [Dynamic Device Discovery Protocol]).
Notes
• The menu displays used for the explanation below may be different depending on the model you
are using.
• Supported Web browsers are Internet Explorer 6/7/8.
• The menu displays only English.
• If the browser of your computer is set to [Use a proxy server] when you have access to the projector
from your computer, click the check mark to set accessing without using a proxy server.
Displaying the Control Window of the Projector with a Web
Browser
You can confirm the IP address of the
projector under “Network Setting” on
the SET SETTING menu.
1 Connect the LAN cable.
LAN cable
(straighttype)
(not supplied)
LAN Connector
The following window appears in the
Web browser:
Hub, router, etc
Once you make the network settings, you
can open the Control window only by
performing step 3 of this procedure.
2 Set the network settings for the
projector using “Network Setting” on
How to operate the Control window
3 Start a web browser on the computer,
enter the following in the address field,
Switching the page
Click one of the Page Switching buttons to
display the desired setting page.
then press the Enter key on your
computer.
(xxx.xxx.xxx.xxx: IP address for the
projector)
Page Switching buttons
Using Network Features 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Confirming the Information
regarding the Projector
You can confirm the current settings for the
projector on the Information page.
No password is set by default. The user
name is preset to “root.” Input required
information after logging in.
Changing the password
Enable: Select to set a new password.
Disable: Select not to change the
password.
Information area
Operating the Projector from
a Computer
You can control the projector from the
computer on the Control page.
Note
If you forget your password, consult with
qualified Sony personnel.
Setting the location
Location: Input information on where
the projector is installed.
Operation area
The functions of the keys shown in the
operation area are the same as those of the
keys on the supplied Remote Commander.
Using the e-mail report
Function
Making the Network Settings
Setting the network password
The log-in screen appears after the Network
page is selected.
Set the e-mail report function on the Mail
Report page. Entered values will not be
applied unless you click on [Apply].
1 Set the e-mail report function.
Enable: Select to activate the e-mail
report function.
Disable: Select to deactivate the e-mail
report function.
28 Using Network Features
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
2 Enter the outgoing e-mail address in
the Send To box then check the Report
Timing check box of the e-mail report
to be sent.
A massage will be sent simultaneously
to secondary recipients by entering their
e-mail addresses in the CC box.
3 Set the timing to send e-mail report.
Over Lamp Usage Time: Tick the box
to send a report that indicates the time
for lamp replacement.
Error: Tick the box to send a report that
indicates an error occurring.
4 Set the mail account for sending e-
mail reports.
User Name: Enter the allocated user
name. Up to 64 characters can be
input.
Password: Enter the e-mail password.
SMTP Server: Enter the address of
outgoing mail server (SMTP). Up to
64 characters can be input.
5 Send the test mail.
Check on the Send test mail check box
then click on [Apply] to send your test
mail to the e-mail address you set.
Notes
• The e-mail report function is not available
because the network which Outbound Port25
Blocking is used cannot be connected to the
SMTP server.
• You cannot use the following characters to
enter the characters in the text box: “ ' ”, “ “
”, “ & ”, “ < ”, “ > ”
Using Network Features 29
Download from Www.Somanuals.com. All Manuals Search And Download.
B Others
Indicators
The indicators allow checking the status and notify you of abnormal operation of the projector.
If the projector exhibits abnormal status, address the problem in accordance with the table
below.
?/1 key
Status
Meaning/Remedies
Lights in red
Flashes in green
The projector is in Standby mode.
• The projector is ready to operate after having been turned on.
• The lamp cools after the projector is turned off.
Lights in green
Lights in orange
Flashes in red
The projector’s power is on.
The projector is in Power Saving Mode (lamp cut off). (page 21)
The projector is in abnormal status. Symptoms are indicated by
number of flashes. Address the problem in accordance with the
following. If the symptom is shown again, consult with qualified Sony
personnel.
Flashes twice
The internal temperature is unusually high. Check the items below.
• Check to see if nothing is blocking the ventilation holes.
Flashes six times Unplug the AC power cord from a wall outlet. After checking that the
?/1 key goes out, plug the power cord to a wall outlet again then turn
on the projector.
Other number of
flashes
Consult with qualified Sony personnel.
LAMP/COVER indicator
Status
Meaning/Remedies
Flashes in red
Symptoms are indicated by number of flashes. Address the problem in
accordance with the following.
Flashes twice
The lamp cover or the air filter cover is not attached securely.
Flashes three times The temperature of lamp is unusually high. Turn off the power and
wait for lamp to cool then turn on the power again. If the symptom is
shown again, the lamp may be burnt out. In such a case, replace the
30 Indicators
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages List
When any of the messages listed below appears on the projected image, address the problem in
accordance with the table below.
Message
Meaning/Remedy
Page
High temp.! Lamp off in Check the items below.
1 min.
• Check to see if nothing is blocking the ventilation holes.
• Check to see if the air filter is not clogged.
Frequency is out of
range!
Change the output setting of the connected equipment to one
for signals supported by the projector.
Please check Input-A
Signal Sel.
Set “Input-A Signal Sel.” to “Auto” or select the input signal
type to suit to the input signal.
Please replace the Lamp Replace the lamp with a new one and clean the air filter. The
and clean the Filter.
message appears whenever you turn on the power until you
replace the lamp and reset the lamp timer.
Not applicable!
Invalid key pressed.
–
The panel keys are
locked!
“Panel Key Lock” is set to “On.”
Messages List 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before asking to have the projector repaired, try to diagnose the problem, following the
instructions below.
Symptom
Remedy
Page
–
The power is not turned Check if the AC power cord is firmly connected.
on.
When the “Panel Key Lock” is set to “On,” you cannot turn on
the projector using the ?/1 key on the projector.
If the lamp or lamp cover is not attached securely, the projector
cannot be turned on.
–
If the air filter or air filter cover is not attached securely, the
projector cannot be turned on.
No image.
Check if the connecting cable is connected to external
equipment firmly.
Check if the computer signal is set for output to an external
monitor. If you set your computer, such as a notebook
computer, to output the signal to both your computer’s display
and an external monitor, the picture of the external monitor
may not appear properly. Set your computer to output the
signal to only an external monitor.
Check if the input source is correctly selected.
Check if the picture is muted.
On-screen display does The on-screen display does not appear when “Status” in the
not appear.
MENU SETTING menu is set to “Off.”
The aspect ratio of the
display is not right/the
image is displayed
Set “Aspect” manually.
smaller /a portion of
image does not appear.
The image is a
trapezoid.
The images become trapezoidal because of the projection
angle. In such a case, you can correct the trapezoidal
distortion, using a Keystone feature.
When the “V Keystone” is set to “Manual,” the keystone
feature does not work automatically. Set “V Keystone” to
“Auto” or “Manual” to set manually.
When the projector is installed on an uneven surface, the
set “V Keystone” manually.
The image is dark/too
bright.
The settings for “Brightness,” “Contrast,” and “Lamp Mode”
affect brightness of the image. Check if the value is
appropriate.
The image will be dark when the lamp is burnt out. Check
“Lamp Timer,” and replace the lamp with a new one if
necessary.
32 Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
Page
The image is not clear.
Check if the projector is in focus.
The picture will not be clear if condensation has accumulated
on the lens. In such a case, let the projector sit for about two
hours with the power on.
–
The image is noisy.
No sound.
Check if the connecting cable is connected to external
equipment properly.
–
–
Check that the connecting cables between the projector and
external video or audio equipment are securely connected.
Check if the output setting of connected external audio
equipment is set to output the audio signal from the projector.
Check if the connecting cable is connected to external
equipment firmly.
Audio is not output if audio muting is activated.
Check if “Volume” is not set to minimum.
Check that the batteries are installed correctly.
Check that the batteries are not exhausted.
–
The Remote
Commander does not
work.
–
The fan is noisy.
The sound from the fan is often greater than normal to cool the
lamp, etc. in the following cases.
• “Lamp Mode” is set to “High.”
• “High Altitude Mode” is set to “On.”
• The unit is used in the location where the temperature is high.
If the ventilation holes are blocked, the internal temperature of
the projector rises and the fan noise becomes larger.
Troubleshooting 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Lamp
Replace the lamp with a new one if a message displayed on the projected image or the LAMP/
Use an LMP-E211 projector lamp (not supplied) for replacement.
1 Turn off the projector, and disconnect
Caution
the AC power cord from a wall outlet.
• The lamp remains hot after the projector is
turned off. If you touch the lamp, you may
burn your finger. When you replace the
lamp, wait for at least an hour after
turning off the projector for the lamp to
cool sufficiently.
2 When the lamp has cooled
sufficiently, open the lamp cover by
loosening 1 screw.
• Do not allow any metallic or inflammable
objects into the lamp replacement slot after
removing the lamp, otherwise it may cause
electrical shock or fire. Do not put your
hands into the slot.
• If the lamp breaks, contact qualified
Sony personnel. Do not replace the lamp
yourself.
• When removing the lamp, be sure to pull it
out straight, by holding the designated
location. If you touch a part of the lamp other
than the designated location, you may be
burned or injured. If you pull out the lamp
while the projector is tilted, the pieces may
scatter if the lamp breaks any may cause
injury.
3 Loosen the 2 screws on the lamp then
pull out the lamp by its grab.
Grab
34 Replacing the Lamp
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Insert the new lamp all the way in until
it is securely in place. Tighten the
2 screws.
Caution
Disposal of the used lamp
For the customers in the USA
Lamp in this product contains mercury.
Disposal of these materials may be
regulated due to environmental
considerations. For disposal or
recycling information, please contact
your local authorities or the
Telecommunications Industry
Association (www.eiae.org).
5 Close the lamp cover and tighten the
1 screw.
Note
Be sure to install the lamp and Lamp cover
securely as it was. If not, the projector
cannot be turned on.
6 Connect the AC power cord to a wall
outlet and turn on the projector.
7 Reset the lamp timer for notification of
the next replacement time.
Select “Lamp Timer Reset” on the SET
SETTING menu then press the ENTER
key. When a message appears, select
Replacing the Lamp 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Air Filter
If the dust cannot be removed from the air filter even after cleaning, replace the air filter with
a new one.
For details on a new air filter, consult with qualified Sony personnel.
Caution
If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the
temperature may rise inside the unit, leading to a possible malfunction or fire.
1 Turn off the projector, and disconnect
4 Attach the air filter cover to the unit.
the AC power cord from the AC outlet.
Note
2 Draw out the air filter cover.
Be sure to attach the air filter cover firmly. If
not, the projector cannot be turned on.
Air filter
3 Clean the air filter with a vacuum
cleaner.
Remove the air filter as illustrated below
then clean with the vacuum cleaner.
Claws
36 Cleaning the Air Filter
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Item
Description
Model
VPL-SX125/VPL-SW125
3 LCD system
Projection system
Display device
Effective display VPL-SX125: 0.63 inch (16.0 mm), 3 plate, Aspect ratio
size
4:3
VPL-SW125: 0.59-inch (15.0 mm), 3 plate, Aspect ratio
16:10
Effective picture VPL-SX125: 2,359,296 pixels (1024 × 768 pixels, 3
elements
plate panels)
VPL-SW125: 3,072,000 pixels (1280 × 800 pixels, 3
plate panels)
Projection lens
Light source
Focus
Manual
High-pressure mercury lamp, 210 W type
Projected image
size
VPL-SX125: 50 inches to 110 inches (1.27 m to 2.79 m)
VPL-SW125: 50 inches to 100 inches (1.27 m to 2.54 m)
Luminous flux
(Brightness)
VPL-SX125: 2500 lm
VPL-SW125: 2600 lm
(when “Lamp Mode” is set to “High”)
Speaker
1 W × 1 (monaural)
Applicable
scanning
frequency
Horizontal: 19 kHz to 92 kHz, Vertical: 48 Hz to 92 Hz
*1
Resolution
When a computer Maximum display resolution: 1400 × 1050 pixels (resize)
signal is input
Panel display resolution:
VPL-SX125: 1024 × 768 pixels
VPL-SW125: 1280 × 800 pixels
When a video
signal is input
NTSC, PAL, SECAM, 480/60i, 576/50i, 480/60p,
576/50p, 720/60p, 720/50p, 1080/60i, 1080/50i
Color system
NTSC3.58, PAL, SECAM, NTSC4.43, PAL-M, PAL-N,
PAL60
Specifications 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Model
VPL-SX125/VPL-SW125
INPUT OUTPUT INPUT A
(Computer/video)
RGB/YPBPR input connector: Mini D-sub 15 pin
female, G with sync/Y: 1 Vp-p 2 dB, sync negative, 75
ohms terminated, RGB/PBPR: 0.7 Vp-p 2 dB, 75 ohms
terminated, Sync signal: TTL level high impedance,
positive/negative
Audio input connector: Stereo mini jack, rated input
500 mVrms, input impedance more than 47 kohms
INPUT B
(VPL-SX125
only)
RGB input connector: Mini D-sub 15-pin female,
RGB: 0.7 Vp-p 2 dB, 75 ohms terminated, Sync signal:
TTL level high impedance, positive/negative
Audio input connector: Stereo mini jack, rated input
500 mVrms, input impedance more than 47 kohms
INPUT B
(VPL-SW125
only)
HDMI input connector: HDMI 19-pin, HDCP support,
HDMI audio support
S VIDEO (S
VIDEO IN)
S video input connector: Mini DIN 4-pin, Y: 1 Vp-p
2
dB, sync negative, 75 ohmes terminated, C: (burst signal)
0.286 (NTSC)/0.3 (PAL/SECAM) Vp-p 2 dB, 75 ohms
terminated
Audio input connector: Phono jack × 2, rated input
500 mVrms, Input impedance more than 47 kohms
VIDEO (VIDEO Video input connector: Phono jack, 1 Vp-p 2 dB,
IN)
sync negative, 75 ohmes terminated
Audio input connector: Shared with S VIDEO IN
OUTPUT
MONITOR output connector: Mini D-sub 15-pin
female, G with sync/Y: 1 Vp-p 2 dB, sync negative, 75
ohms terminated, RGB/PBPR: 0.7 Vp-p 2 dB, 75 ohms
terminated, Sync signal: HD, VD 4 V (open), 1 Vp-p (75
ohms), positive/negative
Audio output connector: Stereo mini jack, stereo, 1
Vrms (maximum volume, when inputting 500 mVrms),
output impedance 5 kohms
Others connector
RS-232C connector: D-Sub 9 pin female
LAN connector: RJ45, 10BASE-T/100BASE-TX
Operating
temperature/
Operating
humidity
0 °C to 40 °C (32 °F to 104 °F)/20% to 80% (no
condensation)
Storage
temperature/
Storage humidity
–10 °C to +60 °C (14 °F to 140 °F)/ 20% to 80% (no
condensation)
Power
100 V to 240 V AC, 3.0 A-1.3 A, 50/60 Hz
requirements
Power
consumption
100 V AC: 290 W
240 V AC: 275 W
Standby power
100 V AC: 3 W (when “Standby Mode” is set to
“Standard”)/1 W (when “Standby Mode” is set to “Low”)
240 V AC: 3 W (when “Standby Mode” is set to
“Standard”)/1 W (when “Standby Mode” is set to “Low”)
38 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Model
VPL-SX125/VPL-SW125
Heat dissipation
100 V AC: 990 BTU
240 V AC: 940 BTU
11
5
Standard
dimensions
(W/H/D)
Approx. 313.4 × 160.3 × 349.3 mm (12 /32 × 6 /16 ×
13 /4)
3
11
23
Approx. 313.4 × 144.9 × 349.3 mm (12 /32 × 5 /32 ×
3
13 /4 inches) (without projecting parts)
Mass
Approx. 3.7 kg (8 lb 3 oz)
Supplied
accessories
See “Checking the Supplied Accessories” in the supplied
Quick Reference Manual.
Optional
accessories
Projector Lamp LMP-E211 (for replacement)
*2 *3
Notes
*2: Information on accessories in this manual is current as of April 2011.
*3: Not all optional accessories are available in all countries and area. Please check with your local
Sony Authorized Dealer.
Design and specifications of the unit, including the optional accessories, are subject to change
without notice.
Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE
FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING
THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR
ANY OTHER REASON WHATSOEVER.
Specifications 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Pin assignment
RGB input connector (Mini D-sub
15-pin, female)
1
2
3
Video input
(red) R
9
Power supply
input for DDC
Video input
(green) G
10 GND
Video input
(blue) B
11 GND
4
5
GND
12 DDC/SDA
RESERVE
13 Horizontal sync
signal
6
GND (R)
14 Vertical sync
signal
7
8
GND (G)
GND (B)
15 DDC/SCL
RS-232C connector (D-Sub 9-pin,
female)
5
1
9
6
1
2
3
4
5
NC
6
7
8
9
NC
RXDA
TXDA
DTR
RTS
CTS
NC
GND
40 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Input connector
Acceptable Input Signals
Computer signal
fH [kHz]/
fV [Hz]
Resolution
*1
RGB
z
HDMI
z
1440 × 900
1280 × 800
55.9/60
49.7/60
Input connector
fH [kHz]/
fV [Hz]
z
z
Resolution
*1
RGB
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
HDMI
640 × 350
31.5/70
37.9/85
24.8/56
31.5/70
37.9/85
31.5/60
35.0/67
37.9/73
37.5/75
43.3/85
35.2/56
37.9/60
48.1/72
46.9/75
53.7/85
49.7/75
48.4/60
56.5/70
60.0/75
68.7/85
64.0/70
67.5/75
77.5/85
61.8/66
60.0/60
75.0/75
Digital TV signal
Input connector
640 × 400
640 × 480
Signal
fV [Hz]
RGB/
YPBPR
*1
HDMI
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
480i
576i
60
50
60
50
60
50
60
50
z
480p
576p
1080i
1080i
720p
720p
800 × 600
z
Analog TV signal
Input
connector
Signal
fV [Hz]
832 × 624
VIDEO /
S VIDEO
z
1024 × 768
z
NTSC
60
50
z
PAL/SECAM
Notes
1152 × 864
*1: Available for VPL-SW125 only.
• When a signal other than the signals listed in
table is input, the picture may not be
displayed properly.
• An input signal meant for screen resolution
different from that of the panel will not be
displayed in its original resolution. Text and
lines may be uneven.
1152 × 900
1280 × 960
z
z
1280 × 1024 64.0/60
80.0/75
91.1/85
z
z
z
z
1400 × 1050 65.3/60
1280 × 768
1280 × 720
1360 × 768
47.8/60
45.0/60
47.7/60
Specifications 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Distance
The following describes the projection distance and height from lens center to bottom of screen
by each projected screen size.
The projection distance is the distance between the front of the lens and the surface of the
projected image.
Height H is the height from the bottom of the projected image (top for ceiling mount) to A
(determined by drawing a perpendicular line from lens center to projected image surface).
Floor Installation (Adjuster (rear) fully extended)
Projection distance L
Projected
image
Front of the lens
Height H from lens
center to bottom
of screen
A
VPL-SX125
Projection distance
Unit: m (inches)
Height H from lens
center to bottom of
screen
Projected image size
Projection
Distance L
Diagonal D
Width × Height
50 inch (1.27 m)
80 inch (2.03 m)
90 inch (2.29 m)
100 inch (2.54 m)
110 inch (2.79 m)
1.02 × 0.76 (40 × 30)
1.63 × 1.22 (64 × 48)
1.83 × 1.37 (72 × 54)
2.03 × 1.52 (80 × 60)
2.24 × 1.68 (88 × 66)
0.61 (24)
1.00 (39)
1.13 (44)
1.26 (50)
1.39 (55)
0.08 (3.00)
0.12 (4.80)
0.14 (5.40)
0.15 (6.00)
0.17 (6.60)
Projection distance formula
D: Projected image size (Diagonal)
H: Distance between the bottom edge of the image and the center of the lens
42 Projection Distance
Download from Www.Somanuals.com. All Manuals Search And Download.
Expression#1
Unit: m (inches)
Projection Distance L
L=0.013009 × D – 0.0384 (L=0.512178 × D – 1.5125)
Expression#2
Height H from lens center to bottom of screen
H=0.00152 × D (H=0.06000 × D)
VPL-SW125
Projection distance
Unit: m (inches)
Height H from lens
center to bottom of
screen
Projected image size
Projection
Distance L
Diagonal D
Width × Height
50 inch (1.27 m)
60 inch (1.52 m)
70 inch (1.78 m)
80 inch (2.03 m)
100 inch (2.54 m)
1.08 × 0.67 (42 × 26)
1.29 × 0.81 (51 × 32)
1.51 × 0.94 (59 × 37)
1.72 × 1.08 (68 × 42)
2.15 × 1.35 (85 × 53)
0.65 (26)
0.79 (31)
0.93 (36)
1.06 (42)
1.34 (53)
0.15 (5.83)
0.18 (7.00)
0.21 (8.16)
0.24 (9.33)
0.30 (11.66)
Projection distance formula
D: Projected image size (Diagonal)
H: Distance between the bottom edge of the image and the center of the lens
Expression#1
Unit: m (inches)
Projection Distance L
L=0.013794 × D – 0.0394 (L=0.543087 × D – 1.5503)
Expression#2
Height H from lens center to bottom of screen
H=0.00296 × D (H=0.11660 × D)
Projection Distance 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Ceiling Installation (Top side parallel to ceiling)
Caution
Never mount the projector on the ceiling or move it by yourself. Be sure to consult with
qualified Sony personnel (charged).
Height H from
lens center to
top of screen
Front of the lens
A
Top side
Projected
image
Projection distance L
VPL-SX125
Projection distance
Unit: m (inches)
Projected image size
Projection
Distance L
Height H from lens
center to top of screen
Diagonal D
Width × Height
50 inch (1.27 m)
80 inch (2.03 m)
90 inch (2.29 m)
100 inch (2.54 m)
110 inch (2.79 m)
1.02 × 0.76 (40 × 30)
1.63 × 1.22 (64 × 48)
1.83 × 1.37 (72 × 54)
2.03 × 1.52 (80 × 60)
2.24 × 1.68 (88 × 66)
0.61 (24)
1.00 (39)
1.13 (44)
1.26 (50)
1.39 (55)
0.08 (3.00)
0.12 (4.80)
0.14 (5.40)
0.15 (6.00)
0.17 (6.60)
Projection distance formula
D: Projected image size (Diagonal)
H: Distance between the top edge of the image and the center of the lens
Expression#1
Unit: m (inches)
Projection Distance L
L=0.013009 × D – 0.0384 (L=0.512178 × D – 1.5125)
44 Projection Distance
Download from Www.Somanuals.com. All Manuals Search And Download.
Expression#2
Height H from lens center to top of screen
H=0.00152 × D (H=0.06000 × D)
In the case of ceiling mounting, check with your dealer regarding the use of a mount kit that is
warranted for use with this product.
VPL-SW125
Projection distance
Unit: m (inches)
Projected image size
Projection
Distance L
Height H from lens
center to top of screen
Diagonal D
Width × Height
50 inch (1.27 m)
60 inch (1.52 m)
70 inch (1.78 m)
80 inch (2.03 m)
100 inch (2.54 m)
1.08 × 0.67 (42 × 26)
1.29 × 0.81 (51 × 32)
1.51 × 0.94 (59 × 37)
1.72 × 1.08 (68 × 42)
2.15 × 1.35 (85 × 53)
0.65 (26)
0.79 (31)
0.93 (36)
1.06 (42)
1.34 (53)
0.15 (5.83)
0.18 (7.00)
0.21 (8.16)
0.24 (9.33)
0.30 (11.66)
Projection distance formula
D: Projected image size (Diagonal)
H: Distance between the top edge of the image and the center of the lens
Expression#1
Unit: m (inches)
Projection Distance L
L=0.013794 × D – 0.0394 (L=0.543087 × D – 1.5503)
Expression#2
Height H from lens center to top of screen
H=0.00296 × D (H=0.11660 × D)
In the case of ceiling mounting, check with your dealer regarding the use of a mount kit that is
warranted for use with this product.
Projection Distance 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Side (Top side parallel to ceiling)
69.4
23
(2 /32)
Center of
the lens
5
79.9 (3 /32)
Unit: mm (inches)
Bottom
1
31
27.3 (1 /16)
24.4 ( /32)
34
11
(1 /32)
40.2
(1 /32)
19
Center of
the lens
1
188
(7 /32)
77 (3 /32)
13
131.8
(5 /16)
40.2
(1 /32)
3
19
5
8.2 ( /16)
31
24.4 ( /32)
23
18.1 ( /32)
29
22.7 ( /32)
1
79.3 (3 /8)
15
125.4 (4 /16)
13
249 (9 /16)
Unit: mm (inches)
Dimensions 47
Download from Www.Somanuals.com. All Manuals Search And Download.
P
About Trademarks
• Adobe and Adobe Acrobat are trademarks
or registered trademarks of Adobe
Systems Incorporated in the United States
and/or other countries.
• Kensington is a registered trademark of
Kensington Technology Group.
• HDMI, HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing
LLC.
R
• Internet Explore is registered trademarks
of Microsoft Corporation in the United
States and/or other countries.
• PJLink is a registered trademark of Japan
Business Machine and Information
System Industries Association.
S
• AMX is a trademark of AMX Corporation.
• All other trademarks and registered
trademarks are trademarks or registered
trademarks of their respective holders. In
™
®
this manual, and marks are not
specified.
T
U
V
Z
Index 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|