Dual Alarm AM/FM Clock Radio
with SmartSet®
Automatic Time Setting System
OWNER’S MANUAL
CKS2000N
CKS2005N
(Black)
(Silver)
IMPORTANT NOTES
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DANGEROUS VOLTAGE
Uninsulated Dangerous Voltage, that may be of sufficient magnitude
to constitute a risk of electric shock to persons is present within this
product's enclosure.
ATTENTION
The Owner's Manual contains important operating and maintenance
instructions.
For your safety, it is necessary to refer to the manual.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
2
PREPARATION FOR USE
UNPACKING AND SET UP
• Remove the radio from the carton and remove all packing material from the
radio. We suggest that you save the packing material, if possible, in the unlikely
event that your radio ever needs to be returned for service. The original carton
and packing material is the only safe way to pack your radio to protect it from
damage in transit.
• Remove any descriptive labels or stickers on the front or top of the cabinet.
Do not remove any labels or stickers from the back or bottom of the cabinet.
• Note the serial number on the bottom of your radio and write this number in
the space provided on Page 1 of this manual.
• Place your radio on a level surface such as a table, desk or shelf, convenient
to an AC outlet, out of direct sunlight, and away from sources of excess heat,
dirt, dust, moisture, humidity, or vibration.
• Unwind the AC power cord and extend it to its full length. The FM antenna is
built in to this cord. It must be fully extended to provide the best FM reception.
POWER SOURCE
This radio is designed to operate on normal 110V-120V 60Hz AC power only. Do
not attempt to operate the radio on any other power source. You could cause
damage to the radio that is not covered by your warranty.
This radio should be connected to an AC outlet that is always ‘live’. Do not connect
it to an outlet that is controlled by a wall switch. When the power to the radio is
interrupted, the built in lithium battery takes over to maintain the time and alarm
settings. To maximize the life of the lithium battery keep the radio connected to a
‘live’ AC outlet at all times
You will note that this system is
equipped with a polarized AC power
plug having one blade wider than the
other. This is a safety feature. If this
plug does not fit into your existing AC
outlet, do not try to defeat this safety
feature by filing the wide blade to make
it fit into your outlet. If this plug will
not fit into your outlet, you probably have an out-dated non-polarized AC outlet.
You should have your outlet changed by a qualified licensed electrician.
3
LOCATION OF CONTROLS AND INDICATORS
1
2
3
4
5
6
7
27
26
8
9
10
11
18 19 20
21
22 23
1 2 1 2
15
1 2 3 8
16
13
14
17
24
25
Top Panel
Right Side
1. Alarm 1 setting button.
2. Alarm Mode button.
(weekdays/weekends/everyday alarm)
3. Time Zone button.
15. Volume control.
16. Band switch (AM/FM).
17. Tuning control.
4. Time setting button.
5. Date setting button.
6. Down button.
Front Panel
18. Alarm 1 ‘On’ indicator.
19. AM indicator.
7. Up button.
8. Alarm 2 setting button.
9. Sleep Timer button.
10. Radio On/Off button.
11. Snooze (Sleep Off) button.
20. Time display.
21. Alarm 2 ‘On’ indicator.
22. Month/Date display.
23. Batt. Low Indicator.
24. Day indicators.
Left Side (Back)
25. Lighted Dial Pointer.
12. Alarm 1 selector switch.
(Radio/Buzzer/Off)
Back Panel
13. Alarm 2 selector switch.
(Radio/Buzzer/Off)
14. Display Dimmer switch (Hi/Low)
26. Back up battery compartment.
27. AC power cord.
4
OPERATING INSTRUCTIONS
SETTING THE TIME, THE FIRST TIME
IMPORTANT:
The first time you connect your new SmartSet® clock radio to the AC outlet the
internal computer will automatically set the time correctly for the Eastern Time
Zone, which is the initial default setting. The display will scan for a few seconds
and then set the correct month, date, day and time in the Eastern zone. If you live
in the Eastern Time zone, there’s nothing else to do. Your clock is set correctly
and running.
If you do not live in the Eastern Time zone you must change the default zone
display to your own zone. You only do this one time and the SmartSet® will
remember the new default zone setting and will always return to that setting after
a power interruption.
There are 7 time zones programmed into your SmartSet® clock radio as follows:
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
-
-
-
-
-
-
-
Atlantic Time
Eastern Time
Central Time
Mountain Time
Pacific Time
Yukon Time
Hawaiian Time
To change the default time zone display, depress the Time Zone button. The
word “ZONE” appears in the main display, and the number “02” will appear on the
month/date display, indicating that the default zone is Zone 2, Eastern Time.
Hold the Time Zone button and then press either the Up or Down buttons until
your own time zone appears on the display, then release the buttons. The clock
display will change to the correct time in the time zone you selected. The clock
will always return to the correct time in the zone you selected after every power
interruption. If you move to a different time zone, simply change the default zone
display to the new zone and the SmartSet® will remember that setting for you.
DATE DISPLAY
The correct month and date appear in the small display. The month and date are
expressed numerically in the MM/DD format. For example, May 21st will be
displayed as (5. 21). This display adjusts automatically for months of different
lengths. For example, at midnight on February 28th (2. 28), the display will
automatically change to March 1st (3.1), unless it is a Leap Year, in which case
the display will change to February 29th (2. 29).
5
YEAR DISPLAY
To see the correct year, depress the Time and Date buttons together. The small
display changes from ‘month/date’ to ‘year’. When you release the Time and
Date buttons the small display returns to month and date.
DAYLIGHT SAVING AND LEAP YEAR ADJUSTMENTS
All Daylight Saving and Leap Year adjustments are made automatically
by the SmartSet® internal computer as follows:
• Start of Daylight Saving Time: At 1:59.59 AM on the first Sunday in
April, the clock will automatically advance to 3:00 AM.
• End of Daylight Saving Time: At 2:59.59 AM on the last Sunday in
October, the clock will automatically reset to 2:00 AM.
• Leap Year: At 12 Midnight on February 28th, the calendar display will
change to "2. 29"
MANUAL TIME ADJUSTMENTS
Some people like to set their clocks 5 to 10 minutes fast to make sure that they
will always be on time. Even though the SmartSet® sets the time by itself, you still
have the option of adjusting the time manually if you wish.
To manually adjust the time display depress and hold the Time button, and press
either the Up or Down buttons to adjust the time display ahead or back as desired.
Each press of the Up or Down buttons will change the display by one minute. If
you hold the Up or Down buttons the display will continue to change. The display
will change slowly at first, one minute at a time. But if you continue holding the Up
or Down buttons the display will change rapidly.
Note: If you manually adjust the time, your new setting is entered into the
SmartSet® memory. If the power is interrupted, the display will return to
your new setting, not the original setting, when the power is restored.
ADJUSTING THE WAKE UP TIMES
Your SmartSet® clock radio has two separate alarms that can be set and used
independently. You may use the alarms to wake two people at different times, or
you may use one alarm for weekdays and the other for weekend wake up times.
The procedure for adjusting the wake up time is the same for both Alarm 1 and
Alarm 2.
6
1. Depress and hold either the Alarm 1 or Alarm 2 setting button. The main
display will change from the correct time to the Alarm 1 or Alarm 2 wake up
time.
2. While holding the Alarm 1 or Alarm 2 setting button, depress either the Up or
Down button to move the display ahead or back to your desired wake up time.
3. When the desired wake up time appears on the display, release all buttons.
Note: Be sure that you have set the wake up time correctly by observing the
AM indicator. If the AM indicator is ‘On’ the wake up time is “AM”. If the
AM indicator is ‘Off’, the wake up time is “PM”.
SELECTING THE ALARM MODE
Your SmartSet® clock radio allows you to select from among three different alarm
operation modes for either alarm. The alarm modes are:
1. Weekdays only - the alarm will only turn on Monday through Friday;
2. Weekends only - the alarm will only turn on Saturday and Sunday;
3. Everyday - the alarm will turn on all 7 days.
To check the Alarm Mode setting for Alarm 1, depress the Alarm 1 setting button.
The display will show the Alarm 1 wake up time and the day of the week indicators
will show you which alarm mode is selected.
• If all 7 indicators are ‘On’, the Everyday mode is selected.
• If only the Monday through Friday indicators are ‘On’, the Weekdays only mode
is selected.
• If only the Saturday and Sunday indicators are ‘On’, the Weekends only mode
is selected.
To change the Alarm Mode setting for Alarm 1, hold the Alarm 1 setting button
and press the Alarm Mode button until the day indicators show the desired mode
setting, Weekdays only, Weekends only, or Everyday operation. Release the
Alarm Mode and Alarm 1 setting buttons and the display will return to the correct
time.
CHECKING THE WAKE UP TIMES AND ALARM MODE
Whenever you want to check the wake up time or the alarm mode settings, simply
press either the Alarm 1 or Alarm 2 setting buttons. The display will change from
correct time to wake up time and the day indicators will show you which alarm
mode is currently selected.
Release the Alarm 1 or Alarm 2 setting buttons to return to correct time.
7
LISTENING TO THE RADIO
• Set the Band selector to the desired band, AM or FM.
• Set the Volume control to a low setting.
• Press the Radio On/Off button to turn the radio ‘On’.
The radio dial pointer wil light.
• Select your desired station with the Tuning control.
• Adjust the Volume control to the desired setting.
• When you are finished listening, press the Radio On/Off button to turn the radio
‘Off’.
The radio dial pointer light goes off.
ANTENNA INFORMATION
AM - The AM bar antenna is inside the cabinet. If AM reception is weak, change
the position of cabinet until the internal antenna picks up the strongest
signal.
FM - The FM antenna is built in to the AC power cord. If FM reception is weak
try varying the position and direction of the power cord until you find the
strongest signal.
WAKE TO RADIO
1. Turn the radio ‘On’ and select the band, station, and volume level that you
wish to hear when the alarm comes on, then turn the radio ‘Off’ again.
2. Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1, Alarm 2, or both alarms.
3. Set the Alarm selector switch for one or both alarms to the ‘Radio’ position.
The appropriate Alarm 1 and/or Alarm 2 indicators will light up to confirm that
the alarms are set.
4. At the selected wake up time the radio will turn ‘On’. It will play for one hour
and then shut off automatically.
5. To stop the radio sooner, press either the appropriate Alarm 1 or Alarm 2
button, or press the Radio On/Off button. The radio will stop but the alarm
remains set and will turn the radio on again at the same time on the following
day (depending on the Alarm Mode setting).
6. If you do not want the alarm to turn the radio on the following day, set the
appropriate Alarm selector to the ‘Off’ position.
8
WAKE TO BUZZER
1. Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1, Alarm 2, or both alarms.
2. Set the Alarm selector switch for one or both alarms to the Buzzer (Buz) position.
The appropriate Alarm 1 and/or Alarm 2 indicators will light up to confirm that
the alarms are set.
3. At the selected wake up time the buzzer will sound. It will continue for one
hour and then shut off automatically.
4. To stop the buzzer sooner, press either the appropriate Alarm 1 or Alarm 2
button. The buzzer will stop but the alarm remains set and will turn the buzzer
on again at the same time on the following day (depending on the Alarm
Mode setting). To stop the buzzer and turn on the radio immediately, press the
Radio On/Off button instead of the Alarm 1 or Alarm 2 button.
5. If you do not want the alarm to turn the buzzer on the following day, set the
appropriate Alarm selector to the ‘Off’ position.
RADIO AND BUZZER OPERATION
You may also set one alarm for wake to radio and the other for wake to buzzer.
Just set the Alarm 1 and Alarm 2 selector switches to the desired positions.
SNOOZE ALARM
After the radio or buzzer alarm sounds in the morning you may press the Snooze
bar for a few more minutes sleep. The alarm will stop for approximately 9 minutes
and then turn on again. You may repeat the Snooze operation up to seven times
if desired, but after the seventh time the alarm will not turn on again.
SLEEP TO MUSIC TIMER
You can program the sleep timer to play the radio for up to 90 minutes and then
shut off automatically.
1. Press the Sleep button. The display will briefly show “10” and the radio will
begin to play. After 10 minutes the radio will shut off automatically. Each time
you press the Sleep button the sleep timer will start at 10 minutes. This is the
sleep timer default setting.
9
2. To increase or decrease the amount of time that the radio will play before
shutting off, hold the Sleep button and press either the Up or Down button
to change the display to the desired sleep time, up to a maximum of 90 minutes
or a minimum of 2 minutes.
Note: When you change the sleep timer from the 10 minute default setting to
a different setting, the new setting becomes the default setting. Whenever
you activate the sleep timer it will begin with your new default setting
and count down to zero from that point.
3. To cancel the sleep timer before it counts down to “00” and shut the radio ‘Off’
immediately, press the Snooze bar.
IMPORTANT:
Remember that the station and volume settings you choose for the Sleep To
Music operation are the same settings you will hear if you set the alarm for wake
to radio the following morning.
DIMMER CONTROL
The Dimmer control was set to the ‘High’ position at our factory. If you find the
clock display is too bright in a darkened room, set the Dimmer control to the ‘Low’
position.
CHANGING THE LITHIUM BATTERY
Like all batteries, eventually the built in lithium battery will need to be replaced. A
number of factors, such as, the length of time between the date the radio was
manufactured and the date you plugged it in for the first time determine the
amount of time before replacement. During this initial storage period, the lithium
battery is supplying power to the SmartSet® computer memory. Once you plug
the radio in, your household outlet supplies the power, and the battery is not
being used. A fresh lithium battery can supply power to the SmartSet® computer
for at least 3 years even if it is never connected to an AC power supply. If your
radio was connected to your AC supply within a few months after it was
manufactured, and you experience only the normal, nuisance type, short duration
power interruptions, your battery may last for up to 5 years or even longer.
When the battery power drops below a certain level, the “BATT. LOW” indicator
will come on. When you see this indicator, you should change the battery as soon
as it is convenient for you to do so. To change the battery proceed as follows:
1. Purchase a replacement 3V lithium battery wherever batteries are sold. The
battery type is CR2430 or equivalent.
10
2. Remove the battery from its package so it is ready to install.
3. Important: Leave the radio power cord connected to your AC outlet. This will
provide power to the SmartSet® computer memory while the original lithium
battery is removed.
4. Remove the battery door by pressing down on the arrow mark and slide the
door in the direction of the arrows.
5. Use a small screwdriver to remove the two small screws securing the battery
cap.
BE CAREFUL NOT TO LOSE THESE SMALL SCREWS!
6. Remove the battery cap. Then remove
STEP 5
the original battery from the holder and
insert the new battery into the holder the
same way.
STEP 6
7. Replace the battery cap. Turn the two
screws clockwise that secure the battery
cap, and confirm that the ‘BATT. LOW’
indicator is ‘Off’.
8. Replace the battery door.
9. Save these instructions. You’ll have to
do this again five to eight years from now!
RESETTING THE CLOCK AFTER A TOTAL MEMORY LOSS
If you do not change the built in lithium battery within a reasonable period of time
after you see the low battery warning indicator, the lithium battery may become
exhausted and will no longer be able to supply back up power to the SmartSet®
internal computer. If the unit is disconnected from the AC outlet after the battery
is exhausted, or if a power interruption occurs, the SmartSet® memory will be lost
and the clock will need to be reset when the power is restored. Be sure to install
a fresh lithium battery before you reset the clock, otherwise the clock will need to
be reset each time the power is interrupted.
11
If the lithium battery is exhausted and you experience an interruption in the AC
power supply, the clock will reset itself to its initial default setting when the power
is restored. The initial default setting is 6:00 AM, Thursday, January 1st (1. 1),
1998. If you notice that the time on your SmartSet® clock radio is completely
incorrect, and the month/date and day indicators are also wrong, press the Time
and Date buttons together to see the year. If the year display is showing “1998”
you probably experienced a total memory loss. To reset the clock after a total
memory loss, proceed as follows:
1. Follow the instructions on page 10 and install a new CR2430 lithium battery in
the battery compartment.
2. Connect the radio to your AC outlet and let the clock set itself.
3. Depress the Time and Date buttons together. The small display will change
from ‘month/date’ to ‘year’.
4. While holding the Time and Date buttons, press the Up (or Down) button to set
the small display to the correct year, then release the buttons.
5. Depress the Date button and the Up (or Down) button to set the small display
to the correct month and date. The Day indicator will change automatically as
you adjust the month/date settings. When the correct month and date appear
on the display, release the buttons.
6. Depress the Time button and the Up (or Down) button to set the main display
to the correct time. Be sure to confirm that you have set the time correctly to
‘AM’ or ‘PM’ by observing the AM indicator.
7. After you set the time, reconfirm that the Day and Month/Date displays are
still correct. Make final adjustments if necessary.
SmartSet® clock memory is now reset and the new lithium battery will maintain it
for the next 5 to 8 years, depending on the number and duration of the power
outages you experience.
IMPORTANT NOTE:
After resetting the clock, don’t forget to reset your wake up times, and alarm
mode settings, and sleep timer settings as well.
12
CARE AND MAINTENANCE
If the cabinet becomes dusty, wipe it with a soft cloth. If the cabinet
becomes smudged or dirty, clean it with a soft, slightly dampened
cloth. Never allow water or any liquid to get inside the cabinet. Never
use any abrasive cleaners or cleaning pads as these will damage
the finish of your radio.
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
CENTER PERMITTED TO PERFORM
WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE,PLEASE WRITE TO:
Emerson Radio Corp.,
Consumer Affairs Dept.,
1901 Diplomat Drive,
Farmers Branch, TX 75234.
13
EMERSON RADIO CORP.
LIMITED WARRANTY
What does this warranty cover ? Any manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions.
For how long? For a period of ninety (90) days from the date of original purchase in the U.S.
What will we do ? If you need service under this Warranty, and you provide us with the dated
proof of purchase, we will provide repair service at no charge for labor and parts at an authorized
Depot Repair Facility, or replace the product in our discretion.
How do you make your warranty claim ? If it becomes necessary to repair your unit, you
can obtain the name and mailing location of a Depot Repair Facility by dialing 1-800-695-0098. You
should pack your unit in a well-padded heavy corrugated box, enclose your check or money order
payable to the Depot Repair Facility in the amount of $9.00 to cover the return shipping and
handling costs, and enclose a copy of your proof of purchase (warranty service will not be provided
without a dated proof of purchase). Finally, you should ship the unit prepaid via UPS or parcel post
(insured).
What does your warranty not cover ? Your warranty does not cover the following :
· Damage from negligence, misuse, abuse, accident, or failure to follow operating instructions.
· Use of product in a commercial application or rentals.
· Changes or repairs by anyone other than an authorized Depot Repair Facility.
· Damage because your unit is improperly connected to the equipment of other manufacturers.
· Unit on which the serial number has been defaced, modified or removed.
· Damage to equipment not properly connected to the product.
· Cost incurred in shipping your unit to and from an authorized Depot Repair Facility.
· Ordinary adjustments which you can perform as outlined in the owner’s manual.
· Signal reception problems caused by external antenna or cable systems.
· Products purchased, used, serviced, or damaged outside of the United States.
· Damage to compact discs or cassettes.
What other limitations apply to your warranty ?
THIS WARRANTY IS NON-TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL
PURCHASER AND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT.
THIS WARRANTY IS VALID O NLY IN THE UNITED STATES O F AMERICA. ANY
APPLICABLE IMPLIED W ARRAN TIES, IN CLU D IN G TH E W ARRAN TY O F
MERCHANTABILITY, ARE LIMITED IN DURATION TO A PERIOD OF THE EXPRESSED
WARRANTY AS PRO VIDED ABO VE BEGINNING WITH THE DATE O F O RIGINAL
PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER EXPRESSED OR IMPLIED,
SHALL APPLY TO THE PRODUCT THEREAFTER. WE MAKE NO WARRANTY AS TO THE
FITNESS OF THE PRODUCT FOR ANY PARTICULAR PURPOSE OR USE.
THE EXTENT OF OUR LIABILITY UNDER THIS LIMITED WARRANTY IS THE REPAIR OR
REPLACEMENT PROVIDED ABOVE AND IN NO EVENT WILL OUR LIABILITY EXCEED
THE PURCHASE PRICE PAID BY THE PURCHASER OF THE PRODUCT. UNDER NO
CIRCUMSTANCES WILL WE BE LIABLE FOR ANY LOSS, DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH
THE USE OF THIS PRODUCT.
How does state law apply to your warranty ?
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, BUT YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW
LIMITATIO NS O N IMPLIED WARRANTIES O R EXCLUSIO N O R LIMITATIO N O F
INCIDENTAL OR CONSEQUENTIAL DAMAGE, SO THESE RESTRICTIONS MAY NOT
APPLY TO YOU.
AU898F
14
EMERSON
Part No.: 16-2783
011-02
800.898.9020
Printed in China
|