iHome iH27 User Manual

Model iH27  
The Portable System  
For Your iPod®  
THIS UNIT WILL NOT CONTROL OR CHARGE 3G iPod  
iH27 Quick start  
1: AC power  
2: batteries  
3: inserts  
Insert 8  
RESET  
R E S E T  
Insert 9  
Insert 10  
Select the dock insert for your  
iPod® model from the table  
below and place insert in dock.  
Never dock an iPod without the  
proper insert in place.  
Attach AC adaptor cable to jack  
on back of the IH27 and plug the  
other end into a wall socket to  
play and charge iPod  
For portable operation, open  
battery compartment on the  
bottom of the unit. Insert 4  
“AA” batteries as indicated.  
iPod nano  
Insert 8  
iPod with video (30GB)  
Insert 9  
iPod with video (60, 80 GB)  
Insert 10  
Inserts are provided for the most  
common models of iPod. Inserts  
for other models are available at  
ALL  
iPod  
nano  
thin (30GB) iPod with video  
thick (60, 80 GB iPod with video  
(800)-288-2792  
4: iPod  
Insert iPod® into dock (iPod must  
not be in a “skin” or case).  
iPod will charge while docked.  
Press the iPod/play Button on  
the IH27 to play your iPod.  
1
Controls and Indicators  
iPod Dock  
Time Set Button  
Alarm On-Off /Set Button  
Sleep / Minute Set Button ꢄ  
Hour Set Button ¿  
Alarm Reset/ ᕣ  
Power Off Button  
iPod Play/Pause ᕢ  
Power ON Button  
Snooze/Dimmer Button ³  
SRS Button  
DST Switch ¹  
Volume Up Button  
¸ Volume Down Button  
Back of Unit  
/off/remote  
lock  
AV out  
line in  
2A  
DC 7.5V  
Line in Jack Ƹ  
DC Jack  
AV out Jack ꢆ  
ƺTravel Lock Switch  
iH27 Display  
Time/Alarm Display  
PM Indicator  
SRS Indicator  
DST Indicator  
Alarm Armed  
iPod Indicator  
Main Battery Low Indicator  
Sleep Display  
Travel Lock Indicator  
Clock Backup Battery Low Indicator  
2
Using the iH27  
Connect iH27 to Power Source  
a) Plug the AC adaptor cable into the ƻ AC Adaptor Jack and the other end into a standard 120v wall socket. Adaptor must be  
plugged in to charge iPod.  
b) For portable operation, install 4 “AA” batteries, 2 in each compartment on the bottom of the unit. Make sure polarity matches  
diagram in compartments.  
Setting the Clock  
a) Press and hold the Time Set Button until the display flashes. Press the Alarm Set Button to toggle between 24 hour (military)  
and 12 hour (standard) time display modes.  
b) Press the Hour Set Button to adjust the hour display (a PM indicator appears when time is set to PM; there is no AM indicator)  
c) Press the Minute Set Button to adjust the minute display. When the correct time is displayed, press the Time Set button  
again. Two beeps will indicate clock setting is complete.  
d) Depending on your location and the time of year, move the DST (Daylight Saving Time) switch on the bottom of the unit to +1  
to add one hour (a DST icon will appear on the display) or to -1 to subtract 1 hour.  
Using the Alarm  
Setting the Alarm  
a) Press and hold the Alarm Set Button until the alarm time flashes to wake to iPod (buzzer alarm sounds if no iPod is detected).  
b) Press the Hour Set Button to set the desired alarm hour (a PM indicator appears when time is set to PM; there is no AM  
indicator)  
c) Press the Minute Set Button to set the alarm minute time. When the desired alarm time is displayed, press the Alarm Set  
Button again. Two beeps will indicate alarm setting is complete. Alarm is now armed, indicated by the alarm clock icon.  
Arming and Disarming Alarm (Turn Alarm Function ON and OFF)  
a) Press the º Alarm On/Off Button to arm or disarm alarm functions. When armed, the alarm icon appears in the display.  
Resetting the Alarm to Come on the Next Day  
a) When the alarm is sounding, press the  
Alarm Reset/Power Off Button to stop the alarm and reset it to come on the following day.  
Snooze  
a) Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes later. Snooze  
can be pressed several times during the 1 hour alarm cycle.  
Sure Alarm  
The iH27 has a sure alarm feature so the buzzer alarm will still sound in the event of power failure, if backup battery is installed.  
iPod  
Playing and charging your iPod  
a) After selecting and placing the proper insert for your iPod model, gently dock iPod in Dock. When docked, iPod will charge  
until fully charged when the iH27 is connected to an outlet with AC adaptor. Unit will not overcharge iPod.  
b) Press the iPod Button to play iPod, and again to pause.  
c) Press ꢅ ꢆ Volume UP or DOWN buttons to adjust iH27 volume up or down.  
e) Press Alarm Reset/Power Off Button to turn iH27 and iPod off.  
3
Using the iH27  
Using Sleep Mode  
a) Press the  
´
Sleep Button while the iPod is playing to enter sleep mode, and continue to press to step through the available  
sleep times: 90, 60, 30 or 15 minutes. The sleep mode icon will appear on the display. The iH27 will play for the number of  
minutes set, growing gradually softer until shutting off both the unit and the iPod at the set time. Press the Volume Up or Down  
controls to set your own sleep volume. Sleep volume setting is separate from your alarm or regular listening volume selection.  
Using the Line-in Jack  
a) An audio patch cord comes with the iH27. Use it to play nondocking iPods or other audio devices through the iH27  
Ƹ
Line-in  
Jack (one end in the device’s line out or headphones jack, the other in the iH27 line in jack). Make sure there is no iPod docked  
in the iH27 when using the line-in jack. Press the iPod Button.  
Using Dimmer  
a) Press the Snooze/Dimmer Button during normal operation to adjust the brightness of LCD display. While operating on AC  
current, the switch will toggle between high, medium, low and off settings. In battery mode, the display is off by default. Press  
once to activate the display for about 3 seconds.  
Using the Travel Lock  
a) You can disable the iH27 controls to avoid turning on the device or changing settings while in transit and to save battery life  
during extended periods of non-use. To do so, move the  
ƺ
Travel Lock Switch (located on the back of the unit) to the Locked  
icon position. A Lock Icon will appear on the display indicating the unit is locked and controls are inactive. Move the switch  
to the Remote positon to restore normal function with remote control capability, or to the Off position to restore function with the  
remote disabled.  
Using the SRS WOW switch  
a)  
Press the  
SRS WOW switch located on the right side of the unit to enable the SRS WOW sound enhancement circuitry.  
This circuitry is designed to provide a broader audio image with enhanced low range and mid range sound reproduction to bring  
added life to compressed MP3 files. The SRS icon will appear in the display when SRS is active. Press switch again to disable  
the SRS WOW effect.  
Using the AV out Jack  
a) To output iPod audio video signal from the iH27 to a TV, computer or other device, connect an iPod AV cable (not included)  
from the  
AV out jack on the back of the iH27 to the AV input on your TV or other device. For use as an audio-only line out,  
you can connect the included audio patch cord from the AV out jack to the audio in jack of another device.  
NOTE: Speakers in the iH27 are not shielded. To avoid possible damage to your TV or monitor from the speaker magnets, do  
not place the iH27 directly on or next to a TV or CRT monitor.  
l.  
4
Replacing iH27 Backup Battery  
Install/Replace Backup Battery  
Battery install for  
Clock display back up  
The iH27 uses a backup battery system to provide continuous alarm operation and  
clock settings in the event of a power failure. If the Backup Battery Low Icon located  
on the left of the display is flashing, it is time to replace the backup batteries. Please  
make sure the AC adaptor is connected, otherwise all settings may be lost during  
battery replacement.  
Open the battery compartment cover located on the bottom of the unit in the left  
battery compartment. Insert 1 “CR2032” battery as indicated. Replace battery  
compartment covers.  
Install/Replace Batteries for Portable Use  
The iH27 uses 4 “AA” batteries for portable playing. If sound becomes weak or  
distorted while operating on batteries, it’s time to replace the batteries.The iH27 will  
not charge iPod while operating on batteries.  
Open the battery compartment covers located on the bottom of the unit.  
Insert 2 AA batteries in each compartment as indicated, making sure the polarity  
(+ and -) matches the diagram.  
Replace battery compartment covers.  
Batteries information:  
Do not mix old and new batteries.  
Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium)  
batteries.  
5
Using The Remote Control Unit (Optional)  
Install/Replace the Remote Control Battery (for models with remote control)  
The remote control battery is already installed at the factory. When the remote control  
stops operating or its range seems reduced, replace the battery with a new one.  
1. The battery door is located on the back end of the unit.  
2. Slide the battery door to release the battery door latch and remove the battery door.  
3. Insert a “CR2032” 3-volt lithium battery. Make sure the polarity (the + and – side of  
the battery) is correct.  
4. Replace the battery compartment door back in the remote control.  
NOTE: PLEASE DISCARD BATTERIES PROPERLY  
Operating the remote control  
®
®
The Remote Control controls basic functions on the iH27 and certain iPod functions when the iPod is docked in the iH27.  
For best results, aim remote control towards the remote sensor by the lower right corner of the display.  
Move the ƺ Travel Lock Switch to Remote position to enable the remote control.  
Turns iH27 OFF or resets alarm when alarm is sounding  
Alarm Reset/  
Power Off Button  
Volume Up Button  
Raises volume level  
Selects iPod and plays track. In play mode, press to pause  
iPod Play/Pause Button  
Button  
Skip to previous or next track when iPod is playing, or  
hold to scan current playing track.  
Button  
Lowers volume level  
Volume Down Button  
Mute Button  
Toggles sound ON or OFF  
SRS Button  
Turn SRS WOW sound enhancement ON or OFF  
Snooze mode when alarm sounds, otherwise dims display  
Selects Sleep Time function  
Snooze/Dimmer Button  
Sleep Button  
6
A Consumer Guide to Product Safety  
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,  
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions  
carefully before installation and use, and keep these instructions handy for future reference. Take special note of all  
warnings listed in these instructions and on the unit.  
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,  
laundry tub, swimming pool or in a wet basement.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation.  
For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also,  
it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air  
through the ventilation openings.  
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances  
(including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating  
instructions or as marked on the appliance.  
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or  
pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the  
unit to where it is plugged into an AC socket.  
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for  
cleaning instructions.  
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any  
openings or vents located on the product.  
8. Attachments – Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable  
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent  
damage to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result  
in a risk of fire or electric shock.  
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:  
A.  
B.  
C.  
D.  
the power supply cable or plug has been damaged.  
objects have fallen into or liquid has been spilled into the enclosure.  
the unit has been exposed to rain.  
the unit has been dropped or the enclosure damaged.  
E.  
the unit exhibits a marked change in performance or does not operate normally.  
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the  
power cable should be unplugged and batteries removed from the unit to prevent damage or corrosion.  
13. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating  
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.  
7
Troubleshooting  
Symptom  
Possible Problem  
Solution  
Unit doesn’t respond  
(no power)  
AC adaptor isn’t plugged into a wall outlet  
or the connector is not plugged into the  
power supply jack on the back of the unit  
Plug the AC adaptor into a wall outlet and plug the  
connector into the supply jack on the unit  
Wall outlet is not functioning or switched off Plug another device into the same outlet to confirm the outlet  
is working. Make sure any associated power switch is ON  
Batteries are weak or dead  
Replace with new batteries  
iPod does not dock  
properly  
Using no or wrong iPod insert  
iPod not installed properly  
Make sure the dock insert is the proper fit for your iPod  
Remove your iPod from the dock and check for  
obstruction on the connectors in the dock and on your  
iPod. Make sure there is no “skin” or case on the iPod.  
Then reseat it in the dock.  
Battery Low icon  
always flashing  
Batteries are weak  
Replace with new batteries  
Batteries were not installed properly  
Check to make sure the polarity ( + and – ends) matches  
the diagram in the battery compartment  
iPod does not  
respond to the unit  
iPod is not installed properly  
Remove your iPod from the dock and check for  
obstruction on the connectors in the dock and on your  
iPod. Then reseat it in the dock.  
Your iPod software is too old  
iPod is locked up  
Upgrade software on your iPod. For details visit  
Please make sure your iPod is working properly before  
docking into the unit. Please refer to your iPod manual for  
details.  
Using 1st or 2nd generation iPod, iPod  
shuffle or other devices.  
iH27 cannot control those iPods or other devices.  
Buttons/Controls  
don’t work  
Move Travel Lock to Off or Remote position  
Press the Menu button on your iPod  
Travel Lock is in Lock position  
If your iPod is not used for some time, it  
may enter deep sleep mode  
iPod does not come  
on immediately  
iPod battery is too run down/weak  
Charge your iPod for about 5 minutes  
NOTE: THIS UNIT DOES NOT CONTROL OR CHARGE 3G iPod  
8
Troubleshooting  
Symptom  
Possible Problem  
Solution  
iPod didn’t charge  
Make sure the iH27 is plugged into a working AC outlet to  
charge your iPod  
Operating iH27 on batteries. The iH27 only  
charges iPod while operating on AC power  
Remove your iPod from the dock and check for  
obstruction on the connectors in the dock and on your  
iPod. Then replace it in the dock.  
iPod is not installed properly  
Please make sure your iPod is working properly before  
docking into the unit. Please refer to your iPod manual for  
details.  
iPod is locked up/ frozen  
iPod battery has problem  
Volume level is set too high  
Sound is distorted  
Decrease the volume  
If the iPod original sound source (MP3) is of poor quality,  
distortion and noise are easily noticed with high-power  
speakers. Try a different audio source such as a music CD.  
Sound source is distorted  
If you are using an external sound source like older  
generation of iPod, try reducing the output volume on the  
device itself.  
Try turning bass boost OFF on your iPod/sound source.  
Replace current batteries with new ones  
Batteries are weak  
Remote Control is not pointed toward  
the iH27 remote sensor or sensor is  
blocked  
Remote Control  
didn’t work  
Point the Remote Control toward the iH27, move within 10  
feet of the unit, make sure sensor is unobstructed  
Battery weak  
Replace current battery with new battery  
Move Travel Lock switch to Remote position  
Travel Lock is in Lock or Off position  
9
Solucionando problemas  
Síntoma  
Causa  
Solución  
El adaptador de AC no está conectado al  
Conecte el adaptador de AC al tomacorriente y también  
La unidad no  
funciona (no circula  
corriente eléctrica)  
tomacorriente o el conector no está conectado conecte el conector a la ficha en la parte posterior de la  
a la ficha en la parte posterior de la unidad  
El tomacorriente no funciona  
unidad  
Coloque otro aparato en ese mismo tomacorriente para  
confirmar si el que no funciona es el tomacorriente  
Las baterías están gastadas  
Reemplace las baterías  
No ha colocado el encastre del iPod, o está  
utilizando el encastre incorrecto.  
El iPod no encastra  
correctamente  
Verifique que el encastre sea el apropiado para su iPod  
El iPod no encastra correctamente  
Quite el iPod del encastre y retire la posible obstrucción  
del encastre o de su iPod. Vuelva a colocar el iPod dentro  
del encastre.  
El ícono de batería  
baja está destellando  
Las baterías están gastadas  
Reemplace las baterías  
Las baterías no están instaladas  
correctamente  
Verifique que la polaridad de las baterías (- y +) se encuentren  
de acuerdo al diagrama del compartimiento de baterías.  
El iPod no se  
comunica con la  
unidad  
El iPod no está instalado correctamente  
Quite el iPod del encastre y verifique posibles  
obstrucciones del encastre o de su iPod. Vuelva a colocar  
el iPod dentro del encastre.  
Su software es obsoleto  
Renueve su software. Para mayor información, diríjase a  
El iPod no responde  
Verifique que su iPod funcione correctamente antes de  
conectarlo a la unidad. Refiérase al manual de su iPod  
para más detalles.  
Usted tiene un iPod de primera o segunda  
generación, un nano u otro tipo de aparato  
El iH27 no puede controlar estos otros aparatos  
Los botones/controles  
no funcionan  
La Traba de viaje se encuentra en  
la posición “ON” (trabada).  
Corra la traba a la posición “OFF” (destrabada)  
NOTA: La unidad no controla o carga iPod de 3A Generación  
10  
Solucionando problemas  
Síntoma  
Causa  
Solución  
El iPod no carga  
El iPod no está instalado correctamente  
Quite el iPod del encastre y retire la posible obstrucción  
del encastre o de su iPod. Vuelva a colocar el iPod dentro  
del encastre.  
El iPod está trabado/no responde  
Por favor asegúrese de que su iPod funcione  
correctamente antes de colocarlo en el encastre.  
Refiérase al manual de su iPod para mayor información.  
La batería del iPod podría tener algún  
inconveniente  
El sonido sale  
distorsionado  
El volumen se encuentra muy alto  
Baje el volumen  
El sonido sale distorsionado de la unidad  
Si el sonido original de su iPod era de pobre calidad, las  
distorsiones y ruidos se harán más notables con los  
parlantes de alta potencia. Pruebe utilizar otra fuente de  
audio como un CD.  
Si está utilizando un iPod de primeras generaciones o un  
nano, intente bajar el volumen de su aparato. También  
intente apagar el amplificador de bajos  
El control remoto no  
funciona  
Las baterías están gastadas  
Reemplace las baterías por nuevas  
No está apuntando el control remoto  
hacia el iH27  
Apunte el control remoto hacia el iH27 y manténgase a  
una distancia máxima de 10 pies de la unidad.  
11  
Limited 90-Day Warranty Information  
Home Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free  
from defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original  
purchase.  
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally  
purchased. Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the  
warranty period, SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $10.00  
charge for handling, packing, return UPS/postage, and insurance). This decision is subject to verification of the defect or  
malfunction upon delivery of this product to the Factory Service Center listed below. The product must include proof of  
purchase, including date of purchase. The fee for service without proof of purchase is $30.00.  
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective  
batteries are the most common cause of problems encountered.  
If service is still required:  
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.  
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty  
period.  
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($30.00 without proof of  
purchase).  
4. Send the unit prepaid and insured, to the Factory Service Center listed below.  
Consumer Repair Department  
SDI Technologies Inc.  
1330 Goodyear Drive  
El Paso, TX 79936-6420  
Disclaimer of Warranty  
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products  
which have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by  
unauthorized persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players,  
CD’s or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the  
owner.  
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original  
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders,  
members or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual,  
exemplary or punitive damages. (Some states do not allow limitations on implied warranties or exclusion of consequential  
damages, so these restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state.  
Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually  
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies  
product.  
© 2007 SDI Technologies, Inc. All rights reserved  
For any other questions: 1-800-288-2792 Toll Free  
iH27-062107-C  
Printed in China  

NAD Classic 523 User Manual
Lenoxx Electronics CD 1493 User Manual
Keurig Inc Coffeemaker B150 User Manual
Kenwood KDC W237S User Manual
Impulse PCW 5181 User Manual
HP Hewlett Packard serviceguard t2808 90006 User Manual
GE PROFILE JP969BH User Manual
Barracuda Networks ST320414A User Manual
Alcatel Carrier Internetworking Solutions 9500 MPR User Manual
Addonics Technologies JCCHDIU64 User Manual