Honeywell Home Security System 35 User Manual

ꢀ

$'(0&2ꢀ9,67$ꢁꢂꢃꢀ

ꢀꢁ3DUWLWLRQHGꢂ6HFXULW\ꢂ6\VWHPꢂ

ꢂ

,QVWDOODWLRQ DQG 6HWXS *XLGH

ꢀ

N7001V5 5/04 Rev A

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

List of Figures...................................................................................................................................... v

Conventions Used in This Manual..................................................................................................... vi

SECTION 1: General Description.....................................................................................................1-1

About the VISTA-40 ...........................................................................................................................................................1-1

Features.............................................................................................................................................................................1-1

SECTION 2: Partitioning...................................................................................................................2-1

Theory of Partitioning.........................................................................................................................................................2-1

Setting-Up a Partitioned System ........................................................................................................................................2-1

SECTION 3: Installing the Control ...................................................................................................3-1

Mounting the Control Cabinet ............................................................................................................................................3-1

Installing the Cabinet Lock.................................................................................................................................................3-1

Grade A Mercantile Premises Listing Guidelines...............................................................................................................3-1

Grade A Mercantile Safe and Vault Listing Guidelines ......................................................................................................3-2

Installing the Control’s Circuit Board ..................................................................................................................................3-2

Installing the Keypads........................................................................................................................................................3-3

Installing External Sounders...............................................................................................................................................3-4

Telephone Line Connections .............................................................................................................................................3-5

Wiring Burglary, Panic and Smoke Detector Devices to Zones 1-9 ...................................................................................3-6

Installing RPM Devices ....................................................................................................................................................3-10

Wireless Zone Expansion.................................................................................................................................................3-13

Installing Relay Devices ...................................................................................................................................................3-16

Installing the Ground Start Module...................................................................................................................................3-17

Installing a Remote Keyswitch .........................................................................................................................................3-18

Remote Keypad Sounder.................................................................................................................................................3-19

Long Range Radio Connected to the J7 Triggers............................................................................................................3-19

Installing a 4100SM..........................................................................................................................................................3-19

Installing the 4285/4286 VIP Module ...............................................................................................................................3-20

Installing the Audio Alarm Verification Module.................................................................................................................3-22

Connecting the Transformer.............................................................................................................................................3-23

Panel Earth Ground Connections.....................................................................................................................................3-25

Determining the Control’s Power Supply Load.................................................................................................................3-25

Determining the Size of the Standby Battery ...................................................................................................................3-26

SECTION 4: Programming................................................................................................................4-1

Program Modes..................................................................................................................................................................4-1

Entering and Exiting Programming Mode...........................................................................................................................4-1

Data Field Programming Mode ..........................................................................................................................................4-1

#93 Menu Mode Programming...........................................................................................................................................4-2

Zone Number Designations................................................................................................................................................4-4

Zone Response Type Definitions .......................................................................................................................................4-5

Zone Input Type Definitions ...............................................................................................................................................4-6

Programming for 4100SM ..................................................................................................................................................4-7

Programming for Access Control........................................................................................................................................4-7

SECTION 5: Data Field Descriptions ...............................................................................................5-1

About Data Field Programming..........................................................................................................................................5-1

Programming Data Fields...................................................................................................................................................5-1

SECTION 6: Downloading Primer ....................................................................................................6-1

General Information ...........................................................................................................................................................6-1

Getting On-Line with a Control Panel.................................................................................................................................6-2

Direct-Wire Downloading....................................................................................................................................................6-3

Telco Handoff.....................................................................................................................................................................6-3

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

SECTION 7: Setting the Real-Time Clock........................................................................................7-1

General Information ...........................................................................................................................................................7-1

Setting the Time and Date .................................................................................................................................................7-1

SECTION 8: User Access Codes......................................................................................................8-1

General Information ...........................................................................................................................................................8-1

User Codes & Levels of Authority ......................................................................................................................................8-1

Multiple Partition Access ....................................................................................................................................................8-2

Adding a Master, Manager, or Operator Code...................................................................................................................8-3

Changing a Master, Manager, or Operator Code...............................................................................................................8-4

Adding an RF Key to an Existing User...............................................................................................................................8-4

Deleting a Master, Manager, or Operator Code.................................................................................................................8-4

Exiting the User Edit Mode.................................................................................................................................................8-4

SECTION 9: Testing the System ......................................................................................................9-1

Battery Test........................................................................................................................................................................9-1

Dialer Test..........................................................................................................................................................................9-1

Burglary Walk-Test (Code + [5] TEST)...............................................................................................................................9-1

Armed Burglary System Test..............................................................................................................................................9-1

Testing Wireless Transmitters............................................................................................................................................9-2

Trouble Conditions.............................................................................................................................................................9-3

To the Installer ...................................................................................................................................................................9-3

APPENDIX A: Regulatory Agency Statements ...............................................................................A-1

UL Installation Requirements............................................................................................................................................ A-1

UL609 Grade A Local Mercantile Premises/Local Mercantile Safe & Vault ...................................................................... A-1

UL365 Police Station Connected Burglar Alarm ............................................................................................................... A-1

UL611/UL1610 Central Station Burglary Alarm................................................................................................................. A-2

California State Fire Marshal (CSFM) and UL Residential Fire Battery Backup Requirements ........................................ A-2

APPENDIX B: Summary of System Commands ............................................................................ B-1

APPENDIX C: Specifications........................................................................................................... C-1

APPENDIX D: Contact ID Event Codes........................................................................................... D-1

TABLE OF CONTACT ID EVENT CODES........................................................................................................................D-1

Index ...........................................................................................................................................Index-1

THE LIMITATIONS OF THIS ALARM SYSTEM

LIMITED WARRANTY

Download from Www.Somanuals.com. All Manuals Search And Download.

List of Figures

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Figure 3-1: Installing the Lock...............................................................................................................................................3-1

Figure 3-2: Cabinet Attack Resistance Considerations.........................................................................................................3-2

Figure 3-3: Mounting the PC Board.......................................................................................................................................3-2

Figure 3-4: Keypad Connections to Control Panel ................................................................................................................3-3

Figure 3-5: Using A Supplementary Power Supply...............................................................................................................3-3

Figure 3-6: Wiring Polarized Fire Devices.............................................................................................................................3-4

Figure 3-7: Wiring Nonpolarized Burglary Devices ..............................................................................................................3-5

Figure 3-8: Telephone Line Connections................................................................................................................................3-6

Figure 3-9: Wiring Connections for Zones 1-9 .......................................................................................................................3-6

Figure 3-10: 2-Wire Smoke Detector on Zone 1 .....................................................................................................................3-7

Figure 3-11: 4-Wire Smoke Detectors ....................................................................................................................................3-8

Figure 3-12: Wiring a 333PRM to the Control.......................................................................................................................3-8

Figure 3-13: Wiring a 333PRM using a 4204 ........................................................................................................................3-9

Figure 3-14: Wiring a 333PRM using a 4204 and a Power Supply ......................................................................................3-9

Figure 3-15: Wiring Latching Glassbreaks to Zone 8...........................................................................................................3-10

Figure 3-16: Polling Loop Connections to the VISTA-40 ....................................................................................................3-11

Figure 3-17: Polling Loop Connections Using One 4297 Extender Module .......................................................................3-12

Figure 3-18: Polling Loop Connections Using Multiple Extender Modules .......................................................................3-12

Figure 3-19: Installing the 5881ENHC with Tamper Protection ........................................................................................3-13

Figure 3-20: 5881 RF Receiver (cover removed) ..................................................................................................................3-14

Figure 3-21: 4204 Relay Module...........................................................................................................................................3-17

Figure 3-22: 4204CF Relay Module......................................................................................................................................3-17

Figure 3-23: Ground Start Module Connections..................................................................................................................3-18

Figure 3-24: Remote Keyswitch Wiring ...............................................................................................................................3-19

Figure 3-25: Remote Keypad Sounder Wiring.....................................................................................................................3-19

Figure 3-26: 4100SM Using a Serial Printer........................................................................................................................3-20

Figure 3-27: VIP Module Connections .................................................................................................................................3-21

Figure 3-28: UVS Connections to the Control Panel...........................................................................................................3-23

Figure 3-29: 1361 Transformer and Battery Connections ..................................................................................................3-24

Figure 3-30: 1361X10 Transformer Connections.................................................................................................................3-24

Figure 6-1: Direct-Wire Downloading Connections...............................................................................................................6-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Conventions Used in This Manual

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Before you begin using this manual, it is important that you understand the meaning of the following

symbols (icons).

These notes include specific information that must be followed if you are installing this system for

a UL Listed application.

These notes include information that you should be aware of before continuing with the

installation, and that, if not observed, could result in operational difficulties.

This symbol indicates a critical note that could seriously affect the operation of the system, or

could cause damage to the system. Please read each warning carefully. This symbol also

denotes warnings about physical harm to the user.

Many system options are programmed in an interactive mode by responding to

alpha keypad display prompts. These prompts are shown in a single-line box.

ZONE PROG?

1 = YES 0 = NO 0

✴

Additional system options are programmed via data fields, which are indicated by a “star” ( )

followed by the data field number.

PRODUCT MODEL NUMBERS:

Unless noted otherwise, references to specific model numbers represent ADEMCO products.

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

General Description

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

About the VISTA-40

The VISTA-40 is a 2-partition, UL Listed control panel with the following features:

•

Provides 64 zones using hardwired, polling loop and wireless.

Provides 70 user access codes

Features

Hardwire and Optional Expansion Zones

•

Provides 9 hardwire zones.

Supports up to 16 2-wire smoke detectors on zone 1.

Supports up to 50 2-wire latching glassbreak detectors on zone 8.

Supports up to 55 additional expansion zones using a built-in polling (multiplex) loop.

Supports up to 64 wireless zones (fewer if using hardwire and/or polling loop zones).

Provides three keypad panic keys: 1 + ✴ (A), ✴ + # (B), and 3 + # (C).

Peripherals Devices

•

Supports up to 16 addressable devices, (keypads, RF receivers, relay modules, etc.).

Provides 8 relays using 4204 and X-10 devices. Can activate relays in response to system events (e.g., alarm, fault,

etc.).

•

Supports the 4285/4286 VIP Module, which allows access to the system from either a remote location or on the

premises

The VIP Module is not Listed for use with the VISTA-40 Control Panel in a UL installation.

•

Supports the 4146 Keyswitch on any one of the system’s 2 partitions.

Arming/Disarming and Bypassing

Provides global arming capability (ability to arm both partitions the user code has access to in one command).

Partitioning

•

Can control 2 separate areas independently, each functioning as if it had its own separate control.

System Communication

•

Supports ADEMCO Contact ID; ADEMCO High Speed; ADEMCO Express; and 3+1, 4+1, and 4+2 ADEMCO and

Sescoa/Radionics Low-Speed formats.

•

Provides an Audio Alarm Verification (AAV) option that permits voice dialog between an operator at the central

station and a person at the premises. An AAV unit, such as ADEMCO UVS, is required.

Downloading

Supports upload and download capability.

•

1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Event Log

•

Provides an event log (history log) that can store up to 100 events.

Can print the event log on a serial printer using a 4100SM.

Can view the event log on an alpha keypad.

Additional Features

•

Provides up to 20 installer-defined, custom words that can be used for zone descriptors.

Contains a built-in User’s Manual, which provides the end user with a brief explanation of the function of a key

when the user presses any of the function keys on the keypad for 5 seconds.

•

Provides trigger outputs, which may interface with Long Range Radio equipment or other devices such as keyswitch

LEDs or printer.

At least one 2-line alpha keypad (6139/6160) must be connected to the system for programming (if you are using

keypad programming), and must remain connected to the system in order to allow the primary user to program

additional user codes into the system at a later time.

1-2

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Partitioning

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Theory of Partitioning

This system provides the ability to arm and disarm up to 2 different areas, as if each had its own control. These areas

are called partitions. A Partitioned system allows the user to disarm certain areas while leaving other areas armed, or

to limit access to certain areas to specific individuals. Each system user can be assigned to operate any or all partitions,

and can be given a different authority level in each.

Before anything can be assigned to those partitions, you must first determine how many partitions (1-2) are required.

Following are some facts you need to know about partitioning.

Keypads

Each keypad must be given a unique "address" and be assigned to one partition.

Zones

Each zone must be assigned to one partition. The zones assigned to a partition will be displayed on that partition’s

keypad(s).

Users

Each user may be given access to one or more partitions. If a user is to operate more than one partition and would like

to arm/disarm all or some of those partitions with a single command, the user must be enabled for Global Arming for

those partitions (when entering user codes).

A user with access to more than one partition (multiple access) can "log on" to one partition from another partition’s

keypad, provided that program field 2*18: Enable GOTO is enabled for each partition he/she wants to log on to from

another.

Setting-Up a Partitioned System

The basic steps to setting up a partitioned system are described below. If you need more information on how to program

the options, see SECTION 4: Programming.

1. Determine how many partitions the system will consist of (programmed in field 2*00).

2. Assign keypads to partitions (Device Programming in the #93 Menu Mode).

3. Assign zones to partitions (Zone Programming in the #93 Menu Mode).

4. Confirm zones are displayed at the keypad(s) assigned to those partitions.

5. Assign users to partitions.

6. Enable the GOTO feature (program field 2*18) for each partition a multiple-access user can log on to (alpha keypad

only).

7. Program partition-specific fields (see the Data Field Descriptions section).

2-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

2-2

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Installing the Control

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

This section describes the procedures for mounting and wiring the control panel and all the peripheral devices.

Mounting the Control Cabinet

To mount the control cabinet, perform the following steps:

Step

Action

Before mounting the circuit board, remove the metal knockouts for the wiring entry that you will be using.

DO NOT ATTEMPT TO REMOVE THE KNOCKOUTS AFTER THE CIRCUIT BOARD HAS BEEN

INSTALLED.

Using fasteners or anchors (not supplied), mount the control cabinet to a sturdy wall in a clean, dry area

that is not readily accessible to the general public. The back of the cabinet has 4 holes for this purpose.

To provide certificated burglary service for UL installations, refer to the special requirements and Figure 3-2

Cabinet Attack Resistance Considerations to follow. For UL Commercial Burglary installations that require

ATTACK RESISTANCE, use the cabinet included in the VISTA-ULKT kit.

Installing the Cabinet Lock

PUSH

ON LOCK

UNTIL IT

IS SEATED

SECURELY

1. Remove cabinet door, then remove the lock

knockout from the door. Insert the key into the

lock.

CHECK

SNAP

TAB

POSITION

LOCKED

PUSH

2. Position the lock in the hole, making certain

that the latch will make contact with the latch

bracket when the door is closed.

SNAP

TAB

UNLOCKED

3. When correctly positioned, push the lock until

it is held securely by its snap tabs.

CABINET DOOR

BOTTOM

STEP 1

STEP 2

Use Part Number K4445 Lock (supplied).

Figu r e 3-1: In sta llin g th e Lock

Grade A Mercantile Premises Listing Guidelines

•

The panel door must be supervised. Mount the

clip-on tamper switch (supplied) to the cabinet’s

right side wall as shown in the diagram below, and

wire it to one of the hardwire zones.

•

All wiring between the bell and panel must be run

in conduit. Remaining wires do not need to be run

in conduit.

All wiring that is not run in conduit must exit from

the knockout openings on the bottom or back of the

cabinet.

Use a bell with a tamper-protected housing such as

the AB12. The bell housing’s tamper switch and

inner tamper linings must also be wired to the

hardwire zone.

All unused knockouts must be plugged using the

disc plugs and carriage bolts (supplied), as

indicated in the diagram below.

Assign the tampers’ hardwire zone to a burglary

partition. Program the hardwire zone for day

trouble/night alarm (zone type 5) when only one

burglary partition is used. Program it for 24-hr.

audible alarm (zone type 7) when more than one

burglary partition is used.

Fasten the cabinet door to the cabinet backbox

using the 18 one-inch-long Phillips-head screws

(supplied) after all wiring, programming, and

checkout procedures have been completed.

3-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

(Shows typical local Grade A listing installation)

RUN BELL WIRES

IN CONDUIT

PLUG THIS

KNOCKOUT

TO PLUG AN UNUSED KNOCKOUT OPENING,

REMOVE KNOCKOUT AND INSTALL A PAIR OF

DISC PLUGS AND A CARRIAGE BOLT AS SHOWN.

CLIP-ON DOOR

TAMPER SWITCH

DISC PLUGS (DIMPLES IN DISC

PLUG SHOULD REGISTER INSIDE

KNOCKOUT OPENING)

CABINET

MOUNTING

HOLE

BOARD

KNOCKOUT

OPENING

(4 PLACES)

PLUG THIS

KNOCKOUT

CARRIAGE BOLT

PLUG THIS

KNOCKOUT

HEX NUT AND

WASHER

CABINET SIDE WALL

(OUTSIDE)

PLUG THIS

KNOCKOUT

RUN ALL REMAINING

WIRE THROUGH HERE

cabattack-001-V0

F igu r e 3-2: Ca bin et Atta ck Resista n ce Con sid er a tion s

Grade A Mercantile Safe and Vault Listing Guidelines

•

Follow the guidelines given above for Grade A

Mercantile Premises listing.

•

For safe and vault applications, a UL Listed

contact must be used inside the cabinet through

one of the knockouts for pry-off tamper purposes.

This sensor also must be wired to a hardwire zone.

•

Mount a shock sensor such as Sentrol No. 5402 to

the control’s backbox. Follow the manufacturer’s

instructions for proper sensor mounting. This

sensor also must be wired to a hardwire zone.

Installing the Control’s Circuit Board

Notes:

To install the circuit board in the cabinet, perform the

following steps:

•

Make certain that the mounting screws are tight.

This ensures that there is a good ground connection

between the PC board and the cabinet.

Step

Action

Hang the three mounting clips on the raised

cabinet tabs. Refer to Figure 3-3 (Detail B).

•

Dress field wiring away from the microprocessor

(center) section of the PC board. Use the loops on

the left and right sidewalls of the cabinet for

anchoring field wiring using tie wraps (Detail C).

These steps are important to minimize the risk of

panel RF interference with television reception.

Make sure the clip orientation is exactly as

shown in the diagram to avoid damage. This

will also avoid problems with insertion and

removal of the PC board.

Insert the top of the circuit board into the slots

at the top of the cabinet. Make certain that the

board rests in the slots as indicated (Detail A).

DETAIL A

SIDE VIEW OF

BOARD INSERTED

INTO SLOTS

Swing the base of the board into the mounting

clips and secure the board to the cabinet with

the accompanying screws.

DETAIL C

SIDE VIEW

OF SLOTS

DETAIL B

SIDE VIEW OF SHORT

MOUNTING CLIPS

(TYP.)

hi_end_mnt-PCB

Figu r e 3-3: Mou n tin g th e P C Boa r d

3-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

Installing the Keypads

•

Up to 31 addressable keypads (addresses 00-30)

may be used (you may need to use an auxiliary

power supply if the 750mA aux. output is

Addressing the Keypads

The keypads will not operate until they are

physically addressed and enabled in the

system’s Device Programming in the #93 Menu

Mode.

exceeded). The following keypads may be used:

•

2-line alpha display, 6139/6160

Set each keypad for an individual address (00-15)

according to the keypad’s instructions. Set an alpha

keypad for address 00 and other keypads for higher

addresses. Any keypads set for address 02 and above

will appear blank until they are enabled in the system’s

program. Each keypad must be set for a different

address.

•

The length of all wire runs combined,

regardless of the wire gauge, must not

exceed 2000 feet when unshielded quad

conductor cable is used (1000 feet if

unshielded cable is run in conduit, which

acts a shield, or if shielded cable is used).

If more than one keypad is wired to one run,

then the above maximum lengths must be

divided by the number of keypads on the run

(e.g., the maximum length is 225 feet if two

keypads are wired on a #22 gauge run).

•

Do not set any keypads to address 31

(nonaddressable mode). They will interfere

with other keypads (as well as other devices)

connected to the keypad terminals.

•

If an “OC” or “OPEN CIRCUIT” message is

present on a keypad, data from the control is

not reaching the keypad. Please check your

wiring.

To wire the keypads, perform the following steps:

Step

Action

Determine wire gauge by referring to the

Wire Run Length/Gauge table below.

Wire Run Length/Gauge Table

Supplementary Power Supply for Additional Keypads

When the control’s auxiliary power load for all devices

exceeds 750mA, you can power additional keypads from

a regulated 12VDC power supply (e.g., AD12612

(1.2A)). Use a UL Listed, battery-backed supply for UL

installations.

Connect the additional keypads as shown in Figure 3-5,

using the keypad wire colors shown. Be sure to observe

the current ratings for the power supply used.

Wire Gauge

#22 gauge

#20 gauge

#18 gauge

#16 gauge

Length

450 feet

700 feet

1100 feet

1750 feet

Wire keypads to a single wire run or connect

individual keypads to separate wire runs.

The maximum wire run length from the

control to a keypad, which is homerun back

to the control must not exceed the lengths

listed in the table.

•

Make connections directly to the screw

terminals as shown in Figure 3-5. Make no

connection to the keypad blue wire (if

present).

•

Be sure to connect the negative (–) terminal

on the power supply unit to terminal 7 (–) on

the control.

Run field wiring from the control to the

keypads (using standard 4-conductor cable

of the wire gauge determined in step 1).

SUPPLEMENTARY

POWER SUPPLY

CONTROL TERMINAL STRIP

AUX. AUX. DATA DATA

Connect the keypad(s) to terminals 6, 7, 8,

and 9 on the control board, as shown in

Figure 3-4.

IN OUT

–

RED

IMPORTANT:

MAKE THESE

CONNECTIONS

DIRECTLY TO

SCREW

BLACK

KEYPADS

GREEN

TERMINALS AS

SHOWN.

YELLOW

CONTROL

TERMINALS

MAIN

KEYPAD

SECONDARY

KEYPAD

Figu r e 3-4: Keypa d Con n ection s to Con tr ol P a n el

Figu r e 3-5: Usin g A Su pplem en ta r y P ower Su pply

3-3

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Installing External Sounders

The VISTA-40 provides a bell circuit output for

operating fire and burglary alarm notification

appliances. The alarm output is rated as follows:

10VDC – 14VDC, 1.7A max., power-limited.

Alarm Output Supervision

When supervision is enabled, the VISTA-40 monitors

the alarm output wiring for open and short circuit

faults while the output is inactive. The system provides

a trouble indication (Zone 70) when an open occurs; or

when a short occurs between the Bell (+) and Bell (-)

terminal wiring, or between the Bell (+) terminal wiring

and earth ground.

The output has the following options:

•

Selectable for supervision.

Selectable for confirmation of arming ding.

Selectable to chime when entry/exit or perimeter

zones are faulted.

The VISTA-40 indicates the trouble condition

regardless of whether the system is armed or disarmed.

The zone displays on the keypads, reports to the event

log, and transmits to the central station (if

•

Selectable for no timeout or timeout of 2-30

minutes.

programmed) on Partition 1. The Contact ID event code

is 321, Bell Trouble. The trouble is cleared from the

display by entering the user code + OFF.

•

Burglary bell circuits must be programmed

for a timeout of 16 minutes or longer.

For Household Fire and combination

Household Fire/Burglary installations, the

total current drawn from the auxiliary power,

polling loop, and alarm output combined

must not exceed 750mA.

Wiring the Alarm Output

The wiring of the alarm output depends upon whether

you are going to supervise the output or not. Use the

appropriate procedure below for your application.

•

For Household Burglary installations, the

total current drawn from the alarm output

must not exceed 1.7A. A battery must be

installed, as it supplies the current for the

combined auxiliary power, polling loop, and

alarm output in excess of 750mA.

Use only UL Listed sounding devices for UL

installations.

Compatible Alarm Indicating Devices

Model Number Device Type

Polarizing

Diode

719

Compact Outdoor Siren

(not UL Listed)

Indoor Siren

Yes

UL1023 Household Burglary Installations

For Household Burglary installations, the total current

drawn from the alarm output must not exceed 1.7A. A

battery must be installed, as the battery supplies

current from the combined auxiliary power, polling

loop, and alarm output in excess of 750mA.

747

Yes

AB12

Grade A Bell

System Sensor

MA 12/24D

Fire Piezo Horn

System Sensor

P12575

Fire Horn/Strobe

UL985 Household Fire or Combination Household

Fire/Burglary Installations

Wheelock

For installations that must provide UL Listed

protection, the total combined current drawn from the

alarm output, auxiliary power output, and polling loop

must not exceed 750mA in order to comply with the

battery independence requirements. If, for example,

two System Sensor PA400 piezo alarm sounders, wired

in parallel, are used (24mA total), then 726mA (750mA

– 24mA) is available for auxiliary output and polling

loop use.

AS-121575W

ALARM SOUNDER OUTPUT:

1-VDC - 13.8VDC

1.7A MAXIMUM

Non-UL Installations

BELL

For non-UL installations, the total current drawn from

this output can be up to 1.7 amps. A battery must be

installed, as the battery supplies current in excess of

750mA. Up to two 719 sirens can be used wired in

parallel.

HORN

This control complies with National Fire

Figu r e 3-6: Wir in g P ola r ized Fir e Devices

Protection Association (NFPA) requirements for

temporal pulse sounding of fire notification

appliances.

3-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

POLARIZING DIODES

(MUST MOUNT AT INDICATING DEVICE)

PANEL BELL

OTHER

DEVICES

HORN

BELL

PANEL BELL

NONPOLARIZED BURGLARY

INDICATING DEVICES

POLARIZED FIRE

INDICATING DEVICE

non_polar_devices

Figu r e 3-7: Wir in g Non p ola r ized Bu r gla r y Devices

Supervising the Alarm Output

Using a Siren Driver

To wire the alarm output using the supervision feature,

perform the following steps:

To install a siren driver, perform the following steps:

Step

Action

Step

Action

Mount the siren driver in the panel’s cabinet.

Wire polarized fire-indicating devices to the

alarm output as shown in Figure 3-6.

Wire the siren driver to the control and to the

speaker(s). (See the driver’s instructions.)

Wire nonpolarized burglary indicating

devices to the alarm output using a polarizing

diode (two 2A diodes supplied), as shown in

Figure 3-7.

Cut the blue jumper on the upper left-hand

corner of the panel’s PC board.

Program Zone 70 with no response type (00).

Program Zone 70 with a response type of 05

(trouble by day/alarm by night).

If a device such as a siren driver with a high-

resistance trigger input (drawing less than 5mA)

is used in a UL Household Fire installation, the

siren driver must independently supervise siren

speaker wiring.

The minimum load on the alarm output must

exceed 5mA at 12V for proper supervision

operation.

Disabling the Supervision of the Alarm Output

To install the alarm output and disable the supervision

feature, perform the following steps:

Step

Action

Wire the devices to terminals 4 and 5,

observing polarity if necessary.

Cut the blue jumper on the upper left-hand

corner of the panel’s PC board.

Program Zone 70 with no response type (00).

Telephone Line Connections

Connect the main dialer output to telephone company

lines using the RJ31X cables supplied.

To prevent the risk of shock, disconnect phone

lines at the telco jack before servicing.

If the communicator is connected to a PABX, be

sure it has a backup power supply that can

support the PABX for 24 hours (central station)

or 60 hours (remote station). Many PABXs are

not power-backed up, and this can result in a

communication failure if power is lost.

The telephone line inputs have overvoltage

protection in accordance with UL1459, as

specified in UL985/UL1023.

Reporting Formats

The system supports the following formats:

ADEMCO Low Speed 3+1; 4+1; 4+2; Sescoa/Radionics

3+1; 4+1; 4+2; ADEMCO 4+2 Express; ADEMCO High

Speed; ADEMCO Contact ID

3-5

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Incoming

Handset

26 27

Telco Line

TERMINALS

ON CONTROL

EARTH GROUND

INCOMING TELCO LINE

DIRECT

CONNECT

CORD

TIP

RING

RJ31X

JACK

PREMISES

PHONES

PLUG

Figu r e 3-8: Teleph on e Lin e Con n ection s

Wiring Burglary, Panic and Smoke Detector Devices to Zones 1-9

The maximum zone resistance is 100 ohms for

zones 1 and 8, and 300 ohms for all other

zones (excluding the 2K EOL resistor).

•

Connect N.C. devices in series with the high (+)

side of the loop. The 2K EOL resistor must be

connected in series with the devices, following the

last device.

To wire burglary and panic devices to zones 1-9, connect

sensors/contacts to the hardwire zone terminals (10

through 23). See Figure 3-9. Connect N.C. and N.O.

devices as follows:

•

Connect N.O. devices in parallel (across) the loop.

The 2K EOL resistor must be connected across the

loop wires at the last device.

Red Jumper

ZONE 2 ZONE 3

ZONE 4 ZONE 5

ZONE 6 ZONE 7

ZONE 8 ZONE 9

ZONE 1

N.C.

N.O.

2k EOLR 2k EOLR

2k EOLR

GLASS

BREAK

Fire

Usage

N.C.

SMOKE

N.C.

N.O.

N.C.

N.O.

Burg.

Usage

2k EOLR

N.O.

Zone resistance (Excluding EOLR):

ZONE 1,8: 100 OHMS MAXIMUM

ALL OTHER ZONES: 300 OHMS MAXIMUM

Zone response time:

2k EOLR

ZONES 1-8: 350mSec-500mSec

ZONE 9: Programmable for

Fast: 10mSec-15mSec

Normal: 350mSec-500mSec

(default response)

Figu r e 3-9: Wir in g Con n ection s for Zon es 1-9

3-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

Using 2-Wire Smoke Detectors on Zone 1

Zone 1 can support up to 16 2-wire smoke detectors.

(+)

(-)

(+)

(-)

The alarm current on zone 1 supports only one

smoke detector in the alarmed state.

2-WIRE SMOKE

DETECTOR

Compatible 2-Wire Smoke Detectors

DETECTOR TYPE

DEVICE MODEL #

Photoelectric, direct-wire

System Sensor 2400

System Sensor 2400TH

System Sensor 2451

System Sensor 2451TH

System Sensor 1400

System Sensor 1451

System Sensor 2451

System Sensor 1451DH

System Sensor 1100

System Sensor 1151

System Sensor 2100

System Sensor 2100T

System Sensor 2151

Figu r e 3-10: 2-Wir e Sm ok e Detector on Zon e 1

Photoelectric w/heat sensor, direct-wire

Photoelectric w/B401B base

Photoelectric w/heat sensor & B401B

Ionization, direct-wire

Using 4-Wire Smoke Detectors on Zones 1-8

You may use as many 4-wire smoke detectors as can be

powered from the panel’s Auxiliary Power output

without exceeding the output’s rating (750mA).

Ionization w/B401B base

Photoelectric duct detect (DH400 base)

Ionization duct detector (DH400 base)

Ionization, direct-wire

Auxiliary power to 4-wire smoke detectors is

not automatically reset after an alarm, and

therefore must be momentarily interrupted

using a 4204 Relay Module.

Ionization w/B110LP base

Compatible 4-Wire Smoke Detectors

Photoelectric, direct-wire

Photoelectric w/heat sensor, direct-wire

Photoelectric w/B110LP base

Use any UL Listed 4-wire smoke detector that is rated

for 10-14VDC operation and that has alarm reset time

not exceeding 6 seconds. Some compatible 4-wire

smoke detectors are listed below.

These smoke detectors are UL Listed for use

with the VISTA-40 and are the only 2-wire

smoke detectors that may be used.

Detector Type

Detector Model #

Photoelectric, direct wire

System Sensor 2412

Photoelectric w/heat

sensor, direct wire

System Sensor 2412TH

Wiring 2-Wire Smoke Detectors to Zone 1

Ionization, direct wire

System Sensor 1412

2K EOL resistors must be used on fire zones

and must be connected across the loop wires

of each zone at the last detector.

Wiring 4-Wire Smoke Detectors

Power to 4-wire smoke detectors must be

To wire 2-wire smoke detectors to zone 1, perform the

following steps:

supervised with an EOL device (use a System

Sensor A77-716B EOL relay module

connected as shown in Figure 3-11).

Step

Action

Select up to 16 2-wire smoke detectors from

the list of compatible detectors.

To wire 4-wire smoke detectors to zones 1-8, perform

the following steps:

Connect 2-wire smoke detectors across zone 1

terminals (10 and 11) as shown in Figure 3-

10. Observe proper polarity when connecting

the detectors.

Step

Action

Select 4-wire smoke detectors (see list of

compatible detectors shown previously in

this section).

Connect the EOL resistor at the last detector

in the loop across the zone 1 terminals. The

EOL resistor must be connected across

the loop wires at the last detector.

Connect detectors (including heat detectors,

if used) across terminals of the zone selected.

All detectors must be wired in parallel. See

Figure 3-11.

Connect the EOLR at the last detector in the

loop across the zone’s terminals. You must

connect the EOLR across the loop wires

at the last detector.

3-7

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

AUXILIARY

POWER

TERMINALS

4-WIRE

SMOKE

EOL POWER

SUPERVISION

RELAY MODULE

A77-716B

DETECTORS

NOTES:

NO CONNECTION

· PROGRAM THE RELAY TO

TRANSFER ON FIRE ZONE

RESET (ACTIVATION CODE 54).

SEE 4204 RELAY MODULE

SECTION FOR DETAILS.

SHOWN POWERED.

RELAY OPENS WHEN

POWER IS LOST.

NC NO

RESET

EOLR

HEAT

DETECTOR

· SECOND CODE AND OFF

ENTERED AT CONSOLE

MOMENTARILY INTERRUPTS

DETECTOR POWER.

RELAY 1, 2, 3, OR 4

4204 RELAY MODULE

FIRE ZONE

TERMINALS

V128BP-002-V0

Figu r e 3-11: 4-Wir e Sm ok e Detector s

Using Smoke Power Reversal Module

The 333PRM reverses polarity to smoke detectors

with Integral Temp-3 Sounders. Typically, in

alarm, each draws 49-60mA of current. The

control panel supplies only enough current for one

smoke detector. In order to attach more than

one, an external power supply and an external

relay may be required.

The 333PRM Polarity Reversing Module is used to

reverse the polarity of the positive and negative

voltages powering smoke detectors. The module is for

use with 4-wire smoke detectors that employ a sounder

and voltage-reversing feature. The module is triggered

by a pulsing bell output.

Smoke Detectors Compatible with the 333PRM

Installing the 333PRM

The 333PRM may be used with the System Sensor

2112/24AT and similar models with the required

operating features previously stated.

Mount the 333PRM inside the control panel’s cabinet or

in a separate cabinet using the double-sided tape

provided. Wire the 333PRM as shown in Figures 3-12,

3-13 or 3-14. Refer to the 333PRM Installation

Instructions for detailed information on the installation

of the module.

CONTROL PANEL

MOMENTARY

RESET SWITCH

–

4-WIRE SMOKE

EOL POWER

DETECTORS

SUPERVISION

RELAY MODULE

A77-761B

SHOWN POWERED.

RELAY OPENS WHEN

POWER IS LOST

-2

2000

OHM

EOLR

JUMPER

HEAT

DETECTOR

JUMPER P1 ON

333 MODULE

MUST BE IN

"B" POSITION

FOUR-WIRE DETECTOR CIRCUIT

TO FIRE ZONE

TERMINALS

Figu r e 3-12: Wir in g a 333P RM to th e Con tr ol

3-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

CONTROL PANEL

–

4-WIRE SMOKE

DETECTORS

EOL POWER

SUPERVISION

RELAY MODULE

A77-761B

SHOWN POWERED.

RELAY OPENS WHEN

POWER IS LOST

-2

2000

OHM

EOLR

JUMPER

HEAT

DETECTOR

JUMPER P1 ON

333 MODULE

MUST BE IN

"B" POSITION

FOUR-WIRE DETECTOR CIRCUIT

TO FIRE ZONE

TERMINALS

NO NC

4204

Figu r e 3-13: Wir in g a 333P RM u sin g a 4204

CONTROL PANEL

–

4-WIRE SMOKE

DETECTORS

EOL POWER

SUPERVISION

RELAY MODULE

A77-761B

SHOWN POWERED.

RELAY OPENS WHEN

POWER IS LOST

-2

JUMPER P1 ON

333 MODULE

MUST BE IN

2000

OHM

EOLR

JUMPER

"B" POSITION

HEAT

DETECTOR

FOUR-WIRE DETECTOR CIRCUIT

TO FIRE ZONE

TERMINALS

USE A 12VDC,

BATTERY-BACKED,

UL LISTED POWER

SUPPLY.

Figu r e 3-14: Wir in g a 333P RM u sin g a 4204 a n d a P ower Su p p ly

3-9

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Using 2-Wire Latching Glassbreaks on Zone 8

GLASSBREAK

DETECTOR

Zone 8 can support 2-wire glassbreak detectors. The

zone provides enough standby current to power up to 50

2-wire glassbreak detectors meeting the requirements

listed below.

ZONE 8

2000

OHMS

EOLR

(+)

(-)

LATCHING TYPE GLASS

BREAK DETECTOR LOOP

Compatible Glassbreak Detectors

Use detectors that meet the following ratings:

Standby

Voltage:

5VDC–13.8VDC

F igu r e 3-15: Wir in g La tch in g Gla ssbr ea k s to Zon e 8

Standby

Resistance:

Greater than 20k ohms (equivalent

resistance of all detectors in parallel)

•

The alarm current provided by zone 8

supports only one glassbreak detector in

the alarmed state.

Alarm

Resistance:

Less than 1.1k ohms (see note below)

Do not use other N.O. or N.C. contacts

when using glassbreak detectors on zone

8. Other contacts may prevent proper

glassbreak detector operation.

Alarm

Current:

2mA–10mA

Reset Time:

Less than 6 seconds

NOTES:

To wire 2-wire latching glassbreak detectors to zone 8,

perform the following steps:

•

You can use detectors that exceed 1.1k ohms in

alarm, provided they maintain a voltage drop of

less than 3.8 volts in alarm.

Step

Action

•

The ASC-SS1 detector has been tested and found to

be compatible with these ratings.

Select compatible 2-wire glassbreak

detectors that meet the requirements stated

previously.

Connect detectors across zone 8 (terminals

21 and 22). See Figure 3-15.

Connect the EOL resistor at the last detector

in the loop across the zone’s terminals. You

must connect the EOL resistor across

the loop wires at the last detector.

Installing RPM Devices

The polling loop provides both power and data to the

RPM devices, and is constantly monitoring the status of

all zones enabled on the loop. The maximum current

draw of all devices on the polling loop cannot total more

than 64mA (unless the system uses a 4297 Polling Loop

Extender Module).

Compatible Polling Loop Devices

Model Number Type

4208

8-Zone Expander

4190WH

4278

2-Zone Expander

Quad PIR

4275

Dual PIR

Devices that can be programmed via either DIP

switches or the built-in unique serial number

must be set for the serial number mode

operation.

4194

Surface-Mount Reed Contact (Wide Gap)

Extender Module

4297

4192SD

4192SDT

Photoelectric Smoke Detector Devices

Photoelectric Smoke Detector w/Heat

Detector

All devices on the polling loop must be wired in parallel

to the [+] and [-] polling loop terminals of the control

panel (24 and 25). You can wire from device to device,

or have multiple branches connected directly to the

control panel in a star configuration.

4192CP

Ionization Smoke Detector

4101SN

Serial Number Single-Output Relay Module

Universal 8-Zone Expander

4208U

4939SN-BR

4939SN-GY

4191SN-WH

4959SN

Serial Number Surface-Mount Reed

Contacts

Serial Number Recessed Reed Contact

Aluminum Overhead Door Contact

3-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

To install polling loop devices, perform the following steps:

Model Number Type

7500

Single Technology Glassbreak Detector

Step

Action

9500

Dual Technology Glassbreak Detector

Universal Group Zoning Module

Serialized 2-Zone Expander

Serialized 1-Zone Expander

Serialized 2-Zone Expander

Serialized PIR

Select devices from the list of compatible

devices shown previously.

4209U

4193SN

4293SN

4190SN

998MX

Set the DIP switches in the device (if

required). Refer to the device’s instructions

for the DIP Switch Tables.

Mount each device in the desired location.

Refer to the device’s instructions.

•

The 4208 must be mounted either inside the

control panel’s cabinet or in a separate

enclosure that has a tamper-supervised cover.

Run wires from the control panel to each

device on the polling loop (see Figure 3-16).

No individual wire run may exceed the

lengths shown in the following table.

The 4190WH right loop must not be used, and

the left loop must be EOLR-supervised.

•

The 4278 right loop cannot be used.

The 4194 is not UL Listed.

Maximum Polling Loop Wire Runs

Wire Gauge

#22 gauge

#20 gauge

#18 gauge

#16 gauge

Max. Length

650 feet

The 4297 must be powered from the control

panel’s Auxiliary Power Output or from a UL

Listed supplementary power supply.

950 feet

1500 feet

2400 feet

•

The 7500 and 9500 detectors are not UL Listed.

For new polling loop installations, always use

twisted pair wiring. In many cases, existing

non-twisted pair wiring may be used, but it is

more susceptible to interference from other

sources, and may be problematic in installations

with long wire runs or in high noise

Wire each device to the polling loop, making

sure of the correct polarity (refer to the

device’s instructions).

NOTE: If you are using serial number

devices, and intend to enroll each device

through the keypad automatically, wire no

more than 25 of these devices to the

control at a time. Then power up and

program them before connecting the next 25.

Leave previously enrolled devices connected.

If you intend to manually enter the serial

numbers through the keypad or through

Compass downloading software, all the

devices may be connected before powering

up to program.

environments.

•

Always locate polling loop wiring at least six

inches (15cm) of AC power, telephone, or

intercom wiring. The polling loop carries data

between the control panel and the devices;

interference on this loop can cause an

interruption of communication. The polling loop

can also cause outgoing interference on the

intercom or phone lines. If this spacing cannot

be achieved, shielded wire must be used. (Note

that the maximum total wire length supported is

cut in half when shielded wire is used.)

POLLING LOOP RATING:

128mA MAXIMUM

•

No more than 64mA may be drawn on any

individual wire run.

When a star configuration is used, the total

length of all wire runs combined cannot exceed

4000 ft (2000 ft. if you are using unshielded wire

in conduit or shielded wire).

4190

RPM

TO RIGHT LOOP

IMPORTANT NOTE: If the installation exceeds or deviates

from these parameters, refer to the application note on the

Honeywell website for additional information. To access

the application note:

4192SD

SMOKE

4278

PIR

1. Go to the honeywell.com/security website

2. Click the Honeywell Security & Custom Electronics link.

3. Click the Commercial link.

Figu r e 3-16: P ollin g Loop Con n ection s to th e

VISTA-40

4. Click the Documentation link.

5. Click the V-Plex Application Note.

3-11

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Polling Loop Supervision

Using the 4297 Polling Loop Extender

A short on the polling loop is indicated by a trouble on

zone 997 and reports as a trouble condition only. If

annunciation is desired, program the zone as type 05.

If a device on the polling loop fails (the panel cannot

"see" that device), the system displays a trouble

condition for all zones on that device. If the panel is

armed when a device fails, and the zone is a burglary

zone, the will go into alarm

The 4297 Polling Loop Extender may be used to provide

additional polling loop current, to extend the polling

loop wire run length, and/or to provide individual

electrically isolated polling loops. Refer to Figures 3-17

and 3-18, to follow.

Be sure to include the total current drawn on

the polling loop when figuring the total auxiliary

load on the panel’s power supply.

A trouble on zone 97 prevents a partition from

being armed, unless all polling loop zones on

that partition are bypassed.

INPUT POLLING LOOP

EXTENSION POLLING LOOP

RPM

OTHER

RPMS

CONTROL PANEL

4297

INPUT LOOP LIMITS:

EXTENSION POLLING LOOP LIMITS = SAME AS INPUT LOOP

• 64 mA MAX. LIMIT CURRENT TO 64mA ON ANY

INDIVIDUAL WIRE RUN.

• NO MORE THAN 55 DEVICES MAY BE USED.

•

NO INDIVIDUAL WIRE RUN CAN EXCEED:

GAUGE LENGTH

COMBINED INPUT AND EXTENSION LOOP LIMITS:

#22

#20

#18

#16

650 FT

950 FT

1500 FT

2400 FT

• NO MORE THAN 55 DEVICES COMBINED.

• TOTAL LENGTH OF ALL WIRE RUNS ON BOTH LOOPS

COMBINED CANNOT EXCEED 5200 FT. (2600 FT. IF

USING UNSHIELDED WIRE IN CONDUIT, OR IF USING

SHIELDED WIRE).

• TOTAL LENGTH OF ALL WIRE RUNS COMBINED CANNOT

EXCEED 5200FT. (2600FT. IF USING UNSHIELDED WIRE).

Figu r e 3-17: P ollin g Loop Con n ection s Usin g On e 4297 Exten d er Mod u le

•

DO NOT CONNECT 4297 MODULES IN

SERIES (i.e., DO NOT CONNECT ONE

MODULE'S EXTENSION LOOP TO

ANOTHER MODULE'S INPUT LOOP.)

EXTENSION POLLING LOOP #1

RPM

4297

INPUT POLLING LOOP

CONTROL PANEL

EXTENSION POLLING LOOP #2

RPM

4297

COMBINED INPUT AND EXTENSION LOOP LIMITS:

NO MORE THAN 55 DEVICES COMBINED ON THE INPUT LOOP AND EXTENSION

LOOP #1. NO MORE THAN 55 DEVICES COMBINED ON THE INPUT LOOP AND

EXTENSION LOOP #2.

•

• TOTAL LENGTH OF ALL WIRE RUNS ON THE INPUT LOOP AND EXTENSION LOOP #1

COMBINED CANNOT EXCEED 5200 FT. (2600 FT. IF USING UNSHIELDED WIRE IN

CONDUIT, OR SHIELDED WIRE). TOTAL LENGTH OF ALL WIRE RUNS ON THE INPUT

LOOP AND EXTENSION LOOP #2 COMBINED CANNOT EXCEED 5200 FT. (2600 FT. IF

USING UNSHIELDED WIRE IN CONDUIT, OR SHIELDED WIRE).

Figu r e 3-18: P ollin g Loop Con n ection s Usin g Mu ltip le Exten d er Mod u les

NOTE: The input loop limits stated in Figure 3-17 apply to Figure 3-18 as well.

3-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

Wireless Zone Expansion

•

Use two identical receivers to provide either a

greater area of coverage or redundant protection.

They must be set for different addresses.

The 5881ENHC RF Receiver and the 5869 Holdup

Switch Transmitter are listed for UL Commercial

Burglary applications. All other RF receivers and

transmitters are not listed for UL Commercial

Burglary applications.

Any zone from 1 to 64 can be used as a 5800 Series

wireless zone, with the exception of zone 64

(reserved for a wireless keypad).

The following table lists the receivers that may be used

and the number of zones they support.

5800 Series Receivers

RF System Installation Advisories

•

Place the receiver in a high, centrally located area.

Do not place it on or near metal objects. This will

decrease the range and/or block transmissions.

Receiver

5881L

Zones

up to 8

up to 16

up to 64

5881M

5881H

Install the RF receiver at least 10 feet from the

control panel or any keypads, to avoid interference

from the microprocessors in these units.

In Canada, 5800 systems must use 5882 Series

receivers: 5882L/5882H. Information to the 5881

Receivers applies as well to the 5882 Receivers.

Both receivers use the same transmitters.

If dual receivers are used:

a. They must be at least 10 feet from each other,

as well as from the control panel and remote

keypads.

b. Each receiver must be set to a different device

address. The receiver set to the lower address

is considered the 1^stRF receiver for supervisory

purposes.

RF System Operation and Supervision

The 5800 RF system operation has the following

characteristics:

•

The receiver responds to a frequency of 345MHz.

The receiver has a nominal range of 200 feet.

c. The House IDs must be the same.

d. Using two receivers does not increase the

number of transmitters the system can support

(63 zones using the 5881H, plus a wireless

keypad).

Supervised transmitters send a supervisory signal

every 70-90 minutes.

•

Zones 88 and 90 are used to supervise the RF

reception of receivers 2 and 1, respectively. The

reception is supervised for two conditions:

Installation and Setup of the 5881 RF Receivers

1. The receiver goes “deaf” (doesn’t hear from any

transmitter) within a programmed interval of

time (defined by program field 1*30).

Take note of the address you select for the RF

receiver, as this address must be enabled in

the system’s Device Programming in the #93

Menu Mode.

2. Proper RF reception is impeded (i.e., jamming

or other RF interference). The control checks

for this condition every 45 seconds.

A response type (05 Day/Night) must be

programmed for zones 90 (1^streceiver) and 88

(2^ndreceiver) for UL installations.

•

The 5881ENHC receiver contains front and back

tampers that permit its use in commercial burglary

installations.

•

You may only mount the 5881ENHC its own plastic

housing. Otherwise, the receiver constantly reports

a tamper condition.

The control checks the receiver connections about

every 45 seconds. The receiver supervisory zone is

89 and 91 for receivers 2 and 1, respectively.

SCREW

NOTE: These zones must be programmed with a

response type (e.g., type 05 Day/Night Trouble)

before they supervise the connection to the receiver.

5881ENHC-001-V0

Figu r e 3-19: In sta llin g th e 5881ENHC with Ta m p er

P r otection

3-13

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

To install the 5881 RF receiver, perform the following

steps:

Step

Action

Step

Action

Connect the receiver’s wire harness to the

keypad terminals (6, 7, 8, and 9). Plug the

connector at the other end of the harness into

the receiver.

Mount the receiver, following the advisories

stated previously.

Set the DIP switches in the receiver for the

address (01-07). See Figure 3-20.

Refer to the Installation Instructions

provided with the receiver for installations

regarding antenna mounting, etc.

Make sure the address setting is not

being used by another device (keypad,

relay module, etc.).

If installing a 5881ENHC, install a flat-head

screw (supplied) in the case tamper tab as

shown in Figure 3-19. When the receiver is

pried from the wall, the tamper tab will break

off and remain on the wall. This will activate

a tamper switch in the receiver and cause

generation of a tamper signal. Note that this

signal will also be generated when the

receiver’s front cover is removed.

ANTENNAS

TO CONTROL'S REMOTE KEYPAD

CONNECTION POINTS.

USE MAX. of 220 ft. [67m of #22 (0.64mm)

WIRE or 550 ft. (168m) of #18 (1mm) WIRE

FOR EACH RUN. OBSERVE 20 ft. MAX.

FOR COMMERCIAL FIRE INSTALLATIONS.

(SEE RECEIVER'S INSTRUCTIONS.)

INSERT IN

RIGHT-HAND

TERMINALS

CIRCUIT

BOARD

MOUNTING

HOLES

YELLOW

RED

BLACK

DIP SWITCH WHITE AREAS = SWITCH

HANDLES. POSITION 2-4 DETERMINE

RECEIVER'S ADDRESS. CONSULT

CONTROL'S INSTRUCTIONS FOR

ADDRESS TO USE. DIP SWITCH BELOW

SHOWN SET FOR ADDRESS "0."

GREEN

WIRING

OPENING

RECEIVER ADDRESS SETTINGS

(" - " MEANS OFF)

SWITCH

POSITION

PRESENT ONLY ON 5881EH (SEE TEXT AT LEFT)

ON ON

DIP SWITCH

INTERFERENCE

INDICATOR LED

PLUG & SOCKET

ON ON ON ON

FOR FUTURE USE

DIP SWITCH #5 (PRESET ONLY ON 5881EH)

ON: SETS 5881EH FOR USE IN COMMERCIAL

FIRE APPLICATIONS (SEE THE RECEIVER'S

INSTRUCTIONS)*.

OFF: USE IN NON-COMMERCIAL FIRE

INSTALLATIONS.

* FOR COMMERCIAL FIRE APPLICATIONS

THE 5881EH PC BOARD MUST BE MOUNTED

IN A SEPARATE CABINET (SEE RECEIVER'S

INSTRUCTIONS FOR DETAILS).

Figu r e 3-20: 5881 RF Receiver (cover r em oved )

3-14

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

5800 Series Transmitter Setup

Installing the 5800TM Module

5800 Series transmitters have the following

characteristics:

Installation of this module is necessary only if you are

using a 5827BD or 5804BD Bi-directional device.

•

Transmitters have built-in serial numbers that

must be enrolled in the system using the #93 Menu

Mode Programming, or input to the control via the

downloader.

The address for the 5800TM must be enabled

in the control’s Device Programming in the #93

Menu Mode as a keypad and then assigned to

a partition.

•

Transmitters do not have DIP switches (except

5827, described separately).

Some transmitters, such as the 5816 and 5817, can

support more than one “zone” (referred to as loops

or inputs). Each loop must be assigned a different

zone number.

For button-type transmitters (wireless keys), such

as the 5804 and 5804BD, you must assign a unique

zone number to each individual button used on the

transmitter.

To install the 5800TM, perform the following steps:

Step

Action

Mount the unit using its accompanying

mounting bracket near the RF receiver.

•

The 5800TM must not be installed within

the control cabinet. It must be between

one and two feet from the receiver’s

antennas.

Transmitter Input Types

Set the module for the appropriate address.

For Address Setting 28 cut the red jumper;

for Address 29 cut the white jumper; for

Address 30 cut both jumpers.

All transmitters have one or more unique factory-

assigned input (loop) codes. Transmitters can be

programmed as one of the following types:

Type

Description

Connect the module’s wire harness to the

keypad terminals (6, 7, 8, and 9). Plug the

connector at the other end of the harness into

the module.

Sends periodic check-in signals, as well as

fault, restore, and low-battery signals. The

transmitter must remain within the receiver’s

range.

(Supervised

RF)

House ID Sniffer Mode

Sends all the signals that the RF type does, but

the control does not supervise the check-in

signals. The transmitter may therefore be

carried off-premises.

(Unsupervised

RF)

This mode applies only if you are using a wireless

keypad (e.g., 5827) or bi-directional devices (e.g.,

5804BD). Use the House ID Sniffer mode to make sure

you do not choose a House ID that is in use in a nearby

system. The House ID must be programmed for the

receiver in Device Programming in the #93 Menu Mode.

These send only fault signals. They do not

send low-battery signals until they are

activated. The transmitter may be carried off-

premises.

(Unsupervised

Button RF)

To enter House ID Sniffer mode, enter your Installer

Code + [#] + [2].

Transmitter Supervision

The receiver now “sniffs” out any House IDs in the area

and displays them. Keep the receiver in this mode for

about 2 hours. Use a House ID that is not displayed.

Exit the Sniffer mode by entering your Installer Code

+ OFF.

Supervised RF transmitters send a check-in signal to

the receiver at 70–90 minute intervals. If at least one

check-in is not received from each supervised

transmitter within a programmed period (field 1∗31),

the “missing” transmitter number(s) and “CHECK” or

“TRBL” are displayed. Unsupervised RF transmitters

(5802MN, 5804) may be carried off the premises.

As Sniffer mode effectively disables RF point

reception, Sniffer mode cannot be entered

while any partition is armed.

Some transmitters have built-in tamper protection, and

annunciate a “CHECK” condition if covers are removed.

If a loss of supervision occurs on a transmitter

programmed for Fire, it reports in Contact ID as

a Fire Trouble (373), not Loss of Supervision

(381), to the central station.

3-15

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Transmitter Battery Life

Some transmitters (e.g., 5802, 5802CP, and 5803)

contain long-life but nonreplaceable batteries. At the

end of their life, the complete unit must be replaced

(and a new serial number enrolled at the control).

Batteries in the wireless transmitters may last from 4

to 7 years, depending on the environment, usage, and

the specific wireless device being used. Factors such as

humidity, high or low temperatures, as well as large

swings in temperature may all reduce the actual

battery life in a given installation.

Button-type transmitters (e.g., 5801, 5802, 5802CP and

5803) should be periodically tested, as these

transmitters do not send supervisory check-in signals.

The wireless system can identify a true low battery

situation, thus allowing the dealer or user of the system

time to arrange a change of battery and maintain

protection for that point within the system.

To test the transmitters using the Transmitter

ID Sniffer mode and the Go/NoGo Test Mode,

see SECTION 10: Testing the System for the

procedures.

Compatible 5800 Series Transmitters

Model

Product

Input Type

UR or RF

BR Only

Model

Product

Input Type

5801

Panic Transmitter

5806/5807/

5808

Wireless Photoelectric Smoke

Detectors

5802

Pendant (Personal Emergency

Transmitter)

5816

Door/Window Transmitter

Miniature Door/Window Transmitter

Temperature Sensor Transmitter

Multi-Point Universal Transmitter

Recessed Transmitter

5802CP

Belt Clip (Personal Emergency

Transmitter)

5816MN

5816TEMP

5817

5802MN

Miniature (Personal Emergency

Transmitter)

UR or RF

5818

5802MN2

Miniature (Personal Emergency

Transmitter)

5827

Wireless Keypad

House ID

5827BD

5849

Wireless Bi-directional Keypad

Glassbreak Detector

5804

Wireless Key Transmitter

BR Only

5804BD

Wireless Key Bi-directional

Transmitter

5850

Glassbreak Detector

5890

PIR Detector

5804BDV

Wireless Key Bi-directional

Transmitter with Voice

BR Only

5890PI

PIR Detector with Pet Immunity

Installing Relay Devices

The VISTA-40 support up to 8 relays. Each device must

be programmed as to how to act (ACTION), when to

activate (START), and when to deactivate (STOP). The

4204 and/or X-10 devices may be used as relay devices.

To install the relay modules, see Figures 3-21 and 3-22

and perform the following steps:

Step

Action

Set the 4204 or 4204CF’s DIP switches for a

device address 01-15.

Installing the 4204 Relay Modules

Do not use an address being used by another

device (keypads, RF receivers, etc.).

Each 4204 module provides 4 relays with Form C

(normally open and normally closed) contacts.

Mount the 4204 and 4204CF Modules per the

instructions provided with them.

The relay module will not operate until the

device address you have set the DIP switches

for is enabled in the control’s Device

Connect the module’s wire harness to the

control (6, 7, 8, and 9). Plug the connector

(other end of harness) to the module.

Programming in the #93 Menu Mode.

If you are mounting remotely, homerun each

module to the control. The table below shows

the maximum wire run lengths. Refer to the

instructions provided with the 4204CF for its

maximum permissible wire lengths.

Wire Gauge Maximum Length

#22

#20

#18

#16

125 feet

200 feet

300 feet

500 feet

3-16

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

SWITCH

POSITION

4 2 0 4 C F A D D R E S S S E T T I N G S

SWITCH

POSITION

4 2 0 4 A D D R E S S S E T T I N G S

("—" means "OFF")

OFF

—

10 11

12 13 14 15

—

10 11

12 13 14 15

—

ON ON

—

ON ON

—

ON ON

—

ON ON

—

ON ON

—

ON ON

—

ON ON

—

ON ON

—

ON ON

—

- ALARM POLARITY

SHOWN

–

DIP SWITCH

- EACH OUTPUT

PROVIDES

RELAY

NOTIFICATION

APPLIANCE B

2K EOLR

4204

FOR SETTING DEVICE

ADDRESS AND

ENABLING/DISABLING

TAMPER

STYLE Y

DIP SWITCH

FOR SETTING DEVICE ADDRESS

AND ENABLING/DISABLING TAMPER

TYPICAL

SUPERVISION

#610-7

(SHOWN "OFF")

- EACH OUTPUT

RATED 1.2A MAX

- USE

NOTIFICATION

APPLIANCES

COMPATIBLE

WITH

POLARIZED

NOTIFICATION

APPLIANCE

–

RELAY

COVER TAMPER (REED) SWITCH

4-PIN CONSOLE PLUG

NOTIFICATION

APPLIANCE A

2K EOLR

4-PIN CONSOLE PLUG

RELAY

NOTIFICATION

APPLIANCE

POWER SUPPLY

VOLTAGE

EITHER OR BOTH

CAN BE USED

#610-7

EITHER OR BOTH

TB1

CAN BE USED

RATING

RELAY

POWER FOR

–

13 14 15 16

TB1

}

NOTIFICATION APPLIANCE A,

NOTIFICATION APPLIANCE B

8-28VDC OR VFW. UP TO 2.4A

DEPENDING ON BELL CURRENT

13 14 15 16

YEL

DATA IN

FROM CONTROL

TB2

BLK

GRN

RED

YEL

BLK

GRN

RED

TB2

DATA IN

(–) GROUND

NOTIFICATION APPLIANCE AND

CONSOLE DATA OUTPUTS ARE

POWER LIMITED

FROM CONTROL

DATA OUT

TO CONTROL

(–) GROUND

(+) 12V; SUPPLIES POWER TO MODULE

CIRCUITRY (INCLUDING NOTIFICATION

APPLIANCE RELAY COILS). CURRENT

DRAIN AT 12V IS: 25 mA + (80 mA PER

ACTIVE OUTPUT)

DATA OUT

TO CONTROL

(+) 12V

Figu r e 3-21: 4204 Rela y Mod u le

Figu r e 3-22: 4204CF Rela y Mod u le

Installing X10 Devices

X-10 devices are either plugged into standard AC

outlets or wired into the AC electrical system by a

X-10 devices require the use of a 1361X10 transformer

in place of the regular 1361 transformer.

licensed electrician, depending on the type of device

used.

X-10 devices respond to “on” and “off” commands sent

from the panel through the 1361X10 transformer.

To connect the 1361X10 transformer, see Connecting the

Transformer, later in this section.

Note each device’s House and Unit Code

setup, as these codes will be used to program

the devices in Output Programming in #93

Menu Mode described in the Programming

Guide.

Installing the Ground Start Module

To install the 675 Ground Start Module, perform the

following steps:

The Ground Start Module is not intended for

use in UL Listed applications.

Step

Action

Determine which side of the telephone line

is the RING side by connecting the (+) lead

of a DC voltmeter to earth ground, and the

(-) lead to one side of the telephone line.

Output 1 may be used to trigger an optional 675

Ground Start Module for installations having telephone

lines that require ground start instead of loop start

operation to obtain a dial tone from the telco central

office.

The wire that reads + 50VDC is the

RING side.

When the panel has a message to transmit to the

central station, it seizes the line, goes off hook, and then

triggers the 675 Module to connect the RING side of the

telephone line to earth ground. The panel causes the

module to break the connection between RING and

earth ground when it obtains a dial tone.

Connect the 675 Ground Start Module to

the panel’s J7 connector trigger output 1, to

auxiliary power, and to the RING side of

the telephone line as shown in Figure 3-23.

Program field 1✳46 Auxiliary Output

Enable with a [0].

You cannot use Output 1 for the Ground Start if

you are using it for Open/Close or an AAV

module.

3-17

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

J7 CONNECTOR

4142TR

CABLE

GRAY (GROUND)

GROUND START

TRIGGER

675

YELLOW (OUT 1)

WHITE (GROUND)

RED (OUT 2)

GROUND

START

MODULE

BLUE

TO AUX. POWER

TERM. 7

BLACK

VIOLET

GREEN (GROUND)

BROWN (OUT 3)

BLUE (GROUND)

BLACK (OUT 4)

(CUT ORANGE

JUMPER)

TO AUX. POWER

TERM. 6

(50mA CURRENT DRAW)

IF USED:

1. OUT 1 IS NO LONGER

USABLE FOR SMOKE DETECTOR RESET

(SEE FIELD 1*46).

TELCO

RING

EARTH

GROUND

2. OUT 2, 3, 4 CAN STILL BE

USED TO PROVIDE ALARM

STATUS INDICATIONS OR

TO OPERATE A KEYSWITCH

(SEE FIELD *15).

3. THE 675 IS NOT UL LISTED.

F igu r e 3-23: Gr ou n d Sta r t Mod u le Con n ection s

Installing a Remote Keyswitch

A UL-Listed remote keyswitch, such as the 4146, can be

used for remote arming/disarming of the burglary

portion of the system and for silencing alarms. The

keyswitch can operate in only one particular partition.

Keyswitch Tamper Operation

The tamper switch need not be used for fire or UL

Household Burglary installations. For UL Commercial

Burglary installations, the tamper switch must be

wired to a zone (zone 6 in Figure 3-24).

The keyswitch is wired across zone 7. This zone is no

longer available as a protection zone. Be sure to

program Zone 7 with a response type (e.g., type 10).

Program that zone for Day Trouble/Night Alarm

(response type 5). When the keyswitch is removed from

the wall, the tamper switch opens, causing an alarm or

trouble on the zone. This also causes the control to

disable keyswitch operation until the tamper is restored

and the associated partition is disarmed.

Operation

•

A momentary short across zone 7 arms the

partition in the AWAY mode, and a short held for

more than 3 seconds arms the partition in STAY

mode. A subsequent short disarms the partition.

Wiring for the Remote Keyswitch

•

The keyswitch LEDs indicate the partition’s status

(see table below).

To install the 4146 keyswitch, perform the following

steps:

A momentary short across Zone 7 silences alarm

bell and keypad sounds, and disarms the system if

it was armed. A subsequent short across Zone 7

clears the alarm memory indication and resets 2-

wire smoke and glassbreak detectors (if used).

Step

Action

Connect the 4146 to the panel as shown in

Figure 3-24.

If you are using the tamper, make sure it is

connected to a zone.

LED Indications

Green

Red

Indication

Off

Disarmed & Ready

Disarmed & Not Ready

Armed Away

Off

On Steady

Slow Flash

Rapid Flash

Off

Armed Stay

Off

Alarm Memory

The keyswitch reports as user 0, if Open/Close

reporting is enabled in field ✳40.

3-18

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

TO AUX POWER

(TERMINAL 6)

YELLOW

RED

(ARMED)

WHITE

GREEN

(READY)

820

ohms

820

ohms

RED

BLACK

TO J7 / OUT 2

TO J7 / OUT 4

2K ELOR

ZONE

TAMPER SWITCH

(CONTACTS CLOSE WHEN

SWITCH DEPRESSED).

LOCK SWITCH

(NORMALLY OPEN)

TO ZONE 7 (+)

(TERMINAL 20)

2K ELOR

J7_keyswitch

Figu r e 3-24: Rem ote Keyswitch Wir in g

Remote Keypad Sounder

An optional Amseco PAL 328N Piezo Sounder can be

used to duplicate the sounds produced by the keypad’s

built-in sounder. The panel will remote all sounds (e.g.,

alarm, trouble, chime, entry/exit, etc.) produced by the

keypad’s built-in sounder except for the short beeps

associated with keypad key depression. One application

of this feature might be to produce chime sounds at a

distant location from the panel’s keypads.

To duplicate the keypad sounds for a particular

partition, program that partition number in field ✳15.

Program field 1✳46 Auxiliary Output Enable with a [2].

J7 CONNECTOR

IF USED.

4142TR CABLE

GRAY (GROUND)

1. OUT 1 IS NO LONGER

USABLE FOR SMOKE

DETECTOR RESET

OR GROUND START

(SEE FIELD 1*46).

2. OUT 2 & 4 CAN NO LONGER

BE USED TO PROVIDE

ALARM TRIGGERS.

YELLOW (OUT 1)

WHITE (GROUND)

RED (OUT 2)

BLACK

–

AMSECO PAL-328N

PIEZO SOUNDER

Remote Keypad Sounder Setup

GREEN (GROUND)

BROWN (OUT 3)

BLUE (GROUND)

BLACK (OUT 4)

To setup for a remote keypad sounder, connect the piezo

sounder to the panel’s positive auxiliary power output

and to Output 1 on the J7 connector as shown in Figure

3-25.

TO AUX POWER +

TERMINAL 6

10mA CURRENT DRAIN)

RED

J7_trigcon-001-V1

Figu r e 3-25: Rem ote Keypa d Sou n d er Wir in g

Long Range Radio Connected to the J7 Triggers

These triggers may be used to trip auxiliary alarm

signaling equipment such as the 7720, 7720ULF, and

7920SE Long Range Radios.

The fire and burglary/audible panic alarm triggers are

normally LOW and go HIGH until a User Code + OFF

is entered in all enabled partition(s) that display these

conditions.

The triggers are common to all partitions and must be

The silent panic/duress trigger latches HIGH, except for

duress, which is momentary.

enabled for each partition (field 2✳20).

Refer to the installation instructions that accompany

your radio for the connections to the control panel.

Installing a 4100SM

The 4100SM is used to print event log reports to a

serial printer.

NOTE: See SECTION 4: Programming for the

programming details when using the 4100SM.

Printer Configurations

Configure the serial printer as follows:

•

8 data bits, no parity, 1 stop bit

1200 baud

Hardware handshaking using DTR.

3-19

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Connecting the 4100SM to a Serial Printer

J8 CONNECTOR

To connect a serial printer using the 4100SM, refer to

Figure 3-26 and perform the following steps:

Action

Step

OUND

OUT

Connect terminal 1 on the 4100SM to the

Violet wire on the 4142TR cable.

4142TR CABLE (SUPPLIED WITH 4100SM)

4100SM SERIAL MODULE

To TB6 Aux. Power (+)

(25mA current draw)

Connect terminal 6 on the 4100SM to the

Brown wire on the 4142TR cable.

+ PWR

- (GND)

RXD

To TB7 Aux. Power (-)

Connect the 4142TR cable to J8 on the

control.

not used

TXD

Connect terminals 8 and 7 of the 4100SM to

terminals 6 and 7 (aux. power (+) and (-)),

respectively of the control.

not used

DTR

RED

BLUE WHITE

Connect the UL EDP Listed serial printer to

the 4100SM Interface Module.

Cable

USE GENDER CHANGER

SUPPLIED WITH 4100SM

IF PRINTER HAS DB25

MALE CONNECTOR

Supplied with

4100SM

The 4100SM Module is supplied with a 10-

foot RS232 cable. A longer cable can be used

if the VISTA-40 is separated from the serial

printer by more than 10 feet, but the total

cable length should be less than 50 feet.

4100SM JUMPERS

(CUT TO SET RESPECTIVE SIGNAL FLOATING)

COLOR

FUNCTION

PIN #

SERIAL PRINTER

SET FOR: 8 DATA BITS

EVEN PARITY

RED

BLUE

WHITE

CTS

DSR

STOP BIT

300/1200 BAUD

Figu r e 3-26: 4100SM Usin g a Ser ia l P r in ter

NOTE: See the 4100SM Installation Instructions for

details concerning the serial printer operation.

Installing the 4285/4286 VIP Module

The 4285/4286 VIP Module is an add-on accessory that

permits the user to access the security system (and

relays) via a TouchTone telephone. This may be done

either from the premises or by calling the premises from

a remote location. Only one VIP Module can be used in

a security system. This module must be enabled as

Device Address 4 in the Device Programming in #93

Menu Mode, and must be assigned to a partition.

The 4285/4286 VIP Module features:

•

Allows the user to receive synthesized voice

messages over the phone regarding the status of

the security system.

•

Allows the user to arm and disarm the security

system and perform most other commands using

the telephone keypad.

•

Allows the user to control relays using the

telephone keypad.

The 4285/4286 VIP Module is not permitted in

UL installations.

Provides voice annunciation over the phone to

confirm any command that is entered.

Announces many of the same words that would

normally be displayed on an alpha keypad under

the same system conditions. Refer to the words in

bold on the Alpha Vocabulary list found in the #93

Menu Mode in the Programming Guide.

Detailed operating instructions for phone access

to the security system are provided with the VIP

Module.

The 4285/4286 is wired between the control panel and

the premises’ handset(s) (see Figure 3-27). It listens for

TouchTones on the phone line and reports them to the

control panel. During on-premises phone access, it

powers the premises phones. During off-premises phone

access, it seizes the line from the premises phones and

any answering machines.

•

Can be supervised for connection to control panel

(annunciated and reported as Zone 804).

• The VIP module will not operate until the

device address (04) is enabled in the control’s

Device Programming in #93 Menu Mode.

• Do not mount the VIP Module on the cabinet

door or attempt to attach it to the PC board.

3-20

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

To install the VIP module, perform the following steps:

Step

Action

Step

Action

Mount the module in the control cabinet if

space is available or, if this is not possible, on

the side of the cabinet or adjacent to it.

Connect the module to the phone line as

shown below. See Figure 3-27.

4285/4286 Terminal

Connects to direct

connect cord:

If you mount the VIP Module inside the

control cabinet, attach it to the cabinet’s

interior surface with 2-faced adhesive tape.

You may leave the module’s cover off if it is

mounted within the cabinet.

1. Phone In (Tip)

2. Phone In (Ring)

3. Phone Out (Tip)

4. Phone Out (Ring)

5. No Connection

6. Audio Out 1∗

green wire

red wire

brown wire

gray wire

If you mount the module outside the

cabinet, use the screw holes at the rear to

mount horizontally or vertically (2-faced

adhesive tape may be used, if preferred).

Speaker

7. Audio Out 1∗

Supported by the 4286 only

Affix the 4285/4286 connections label

(supplied separately) to the inside of the VIP

Module’s cover, if the cover is used.

Otherwise, affix the label to the inside of the

control cabinet’s door.

Use an RJ31X Jack with the phone cable

supplied with the control to make connections

to the VIP module. Make connections exactly

as shown in Figure 3-27. This is essential,

even if the system is not connected to a

central station. The 4285/4286 will not

function if this is not done.

Make 12V (+) and (–) and data-in and data-

out connections from the VIP Module to the

control, using the connector cable supplied

with the VIP Module. These are the same

connections as for remote keypads.

• If touch-tones are not present following phone

access to the security system via an on-

premises phone, try reversing the pair of

wires connected to terminals 3 and 4 on the

4285/4286.

• If the phone plug is disconnected from the

control, the premise’s phones will not operate.

SPEAKER NOTE: IF CONNECTING SINGLE SPEAKER, USE 8-ohm SPEAKER ONLY.

IF CONNECTING 2 SPEAKERS, USE 4-ohm or 8-ohm SPEAKERS

AND CONNECT IN SERIES.

INCOMING TELCO LINE

SEE SPEAKER NOTE

4286 VIP MODULE

NOTE:

GREY

BROWN

TIP

RING

RJ31X

JACK

4286 DEVICE

ADDRESS IS

FACTORY SET

TO “4”

SPEAKER

VOLUME

CONTROL

PREMISES

ANSWERING

MACHINE AND

PHONES

CALLER ID

UNIT

CONNECTION

KEYED

HEADER

ANSWERING

MACHINE

EARTH

GROUND

TO CONTROL PANEL

KEYPAD CONNECTIONS

TIP RING TIP RING

HANDSET INCOMING

TELCO LINE

YELLOW

GREEN

4500

YELLOW

THERMOSTAT

NO CONNECTION

RED

BLACK

GREEN

IMPORTANT NOTE FOR EXISTING INSTALLATIONS:

EXISTING WIRES CONNECTED TO THE “HANDSET”

TERMINALS ON CONTROL MUST BE MOVED FROM

THERE TO TERMINALS 3 AND 4 ON THE 4286.

THIS DEVICE COMPLIES WITH FCC RULES, PART 68

FCC REGISTRATION No. AC3USA-74659-KX-N

RINGER EQUIVALENCE: 1.0B

U.S. PATENT No. 4791658

FOR COMPLETE INFORMATION, SEE INSTALLATION

INSTRUCTIONS N6431-3 ACCOMPANYING 4286 VIP

MODULE

4286_wiring-002-V1

Figu r e 3-27: VIP Mod u le Con n ection s

3-21

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Installing the Audio Alarm Verification Module

Audio Alarm Verification (AAV) is not permitted

in UL installations.

If the phone plug is disconnected from the

control, the premise’s phones will not operate.

NOTES:

•

685 Receiver software must be rev. 4.6 or

higher. Earlier versions will not hold the

phone line connection.

•

When the AAV indicates that the audio alarm

verification session is completed, all keypad sounds

are restored. Sirens are restored if the alarm

timeout period has not expired.

As part of its fail-safe software, the control limits

all audio alarm verification sessions to 15 minutes.

This is because once the session begins, the AAV

Module controls the duration.

If a new Fire alarm should occur during a session,

the control breaks the phone connection and sends

the new Fire Alarm report, then re-triggers the

AAV Mode. All other dialer messages triggered

during ongoing conversation are held until either

the AAV Module signals that it is inactive, or the

15-minute timeout occurs.

Contact ID code for “Listen-in to Follow” is

606. Contact ID is the only reporting format

that will send a “Listen-in to Follow.”

If you are also using a 4285/4286 VIP

Module, be sure to follow Figure 3-30 when

making connections.

The UVS consists of a UVCM and at least one UVST.

The UVCM board has a DC power jack and a 34-

position terminal block for making connections to a DC

power source, UVSTs, telephone lines, music source, or

to the 4286 VIP Module; and to a control panel’s voice

trigger and bell outputs (if required). Refer Figure 3-28

for wiring connections. For a detailed explanation of

the wiring connections and the functions of the DC

power jack and terminal block positions, refer to the

installation instructions that accompany the UVS.

3-22

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

UVCM AND UVST SUMMARY OF CONNECTIONS

Refer to UVS Installation and Setup Guide K4214 for complete information

SWITCH BANK 2

NOTE 1: CONNECT TO PROPER EARTH GROUND.

SWITCH BANK 1

NOTE 2: POWER MAY ALSO BE SUPPLIED BY A LISTED CLASS 2

POWER SUPPLY RATED 12VDC, MIN 600mA CONNECTED TO THE

UVCM +12VDC IN AND GND TERMINALS.

FUTURE USE, SET TO ON

UVST 1 AUX AUDIO, ON = ENABLED

UVST 2 AUX AUDIO, ON = ENABLED

UVST 3 AUX AUDIO, ON = ENABLED

UVST 4 AUX AUDIO, ON = ENABLED

UVST 5 AUX AUDIO, ON = ENABLED

UVST 6, ON = OUTSIDE, OFF = INSIDE

UVST 7, ON = OUTSIDE, OFF = INSIDE

VOICE TRIGGER, ON = IMMED, OFF = CALLBACK

TELEPHONE RING, ON = ENABLED

END USER VOICE, ON = DISABLED

FUTURE USE, SET TO ON

CS CODE LEARN, ON = DISABLED

USER CODE LEARN, ON = DISABLED

FUTURE USE, SET TO ON

NOTE 3: SOME CONTROL PANELS USE BUILT-IN TRIGGER AND SOME

USE 4204 RELAY MODULE. REFER TO AAV SECTION OF CONTROL PANEL

INSTALLATION AND SETUP GUIDE FOR CONNECTION.

NOTE 4: EITHER MUSIC SOURCE OR 4286 VIP MODULE CAN BE USED BUT

NOT AT THE SAME TIME.

NOTE 5: DO NOT CONNECT IF 4286 VIP MODULE IS USED.

SHIPPED WITH ALL SWITCHES IN "ON" POSITION.

SWITCH BANK 1

SWITCH BANK 2

ALTERNATE

+12 VDC IN FOR

PLUG-IN WALL PACK

(SEE NOTE 2)

AUXILIARY

AUDIO LEVEL

ADJUSTMENT

TRIM POT

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

NOTE 1

MUSIC SOURCE

OPTIONAL

(NOTE 4)

AUDIO OUT

GND

TIP

RJ31X

JACK

INCOMING

TELCO

LINES

PLUG

CONTROL PANEL

RING

DIRECT

CONNECT

CORD

INCOMING RING

INCOMING TIP

HANDSET RING

HANDSET TIP

SPEAKER

VOLUME

CONTROL

SPEAKER

VOLUME

TRIM POT

VOLUME CONTROL DIAL

4286 VIP

MODULE

OPTIONAL

(NOTE 4)

UVST

KEYED

HEADER

ANSWERING

MACHINE

TYPICAL 1 OF 7

FOR COMPLETE INFORMATION, SEE

4286 VIP MODULE INSTRUCTIONS.

COMPLIES WITH FCC RULES, PART 68

FCC REGISTRATION NO. AC3 USA-40133-SP-T

RINGER EQUIVALENCE: 1.0B

PREMISES

ANSWERING

MACHINE AND

PHONE (S)

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MAY CAUSE UNDESIRED OPERATION.

WARNING: TO PREVENT RISK

OF ELECTRICAL SHOCK,

DISCONNECT TELCO JACK

BEFORE SERVICING THIS PANEL.

Figu r e 3-28: UVS Con n ection s to th e Con tr ol P a n el

Connecting the Transformer

This product uses the 1361 transformer (1361CN in

Canada). If you are using X-10 devices, the 1361X10

transformer interface must be used in stea d of the

regular 1361 transformer. The 1361X10 supplies the

control panel with AC, and also sends control pulses

through the premises electrical system to control the X-

10 devices.

Use 1361CN Transformer in Canadian

installations.

3-23

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Power Limiting Outputs

Failure to observe the polling loop current

rating will cause polling loop malfunction.

Failure to observe the auxiliary power current

rating will result in a battery that does not

charge properly or possibly a tripped circuit

breaker.

All outputs are power-limited as per UL985/UL1023.

The following table shows the maximum current that

may be drawn from each output.

Output

Maximum Current Draw

Auxiliary Power

Polling Loop

Alarm Output

750mA

64mA

1.7A

To connect the transformer to the control, perform the

following steps:

Step

Action

For Household Fire or Combination Household

Fire/Burglary Installation: The total current drawn

from the auxiliary power, the polling loop, and the

alarm output combined must not exceed 750mA to

comply with the battery independence requirements in

UL985.

Connect all installed devices to the control.

Wire the 1361 Transformer (1361CN in

Canada) to the panel (before connecting the

battery) as shown in Figure 3-29, or wire the

1361X10 Transformer as shown in Figure 3-

30 (if using X-10 devices).

For Household Burglary-Only Installations: The

total current drawn from the alarm output may be up to

1.7A. A battery must be installed to supply the current

of the combined auxiliary power, polling loop, and

alarm output in excess of 750mA.

Plug the transformer into a 24-hour,

uninterrupted, 120VAC, 60Hz outlet. After

a few seconds, the keypad display appears.

BATTERY

TABS

PRIMARY POWER

Connect to

12VDC, 4AH

or 12VDC, 7AH

Supplied by a transformer

which is rated at

16.5VAC, 40VA.

Caution must be taken when

wiring this transformer to the

panel to guard against blowing

the fuse inside the transformer

(non-replaceable).

GEL CELL

BATTERY

CHARGING

VOLTAGE

13.7VDC

Connect to

24hr. source

of AC mains

TRANSFORMER

16.5VAC, 40VA

NOTE:

WHEN POWERING UP

THE PANEL, PLUG THE

TRANSFORMER IN BEFORE

CONNECTING THE BATTERY.

ADEMCO No.1361

or 1361X10, if X-10

DEVICES WILL BE USED.

Figu r e 3-29: 1361 Tr a n sfor m er a n d Ba tter y Con n ection s

X10 TRANSFORMER/INTERFACE

J8 CONNECTOR

4142TR CABLE

TERMINALS

ON CONTROL

BOARD

1361X10-001-V0

Figu r e 3-30: 1361X10 Tr a n sfor m er Con n ection s

3-24

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

Panel Earth Ground Connections

In order for the lightning transient protective devices in

this product to be effective, the designated earth ground

terminal (terminal 30) must be terminated in a good

earth ground. Recommended wire gauge for the ground

connection is #16 AWG, run no farther than 30 feet.

The following are examples of good earth grounds

available at most installations:

•

AC Power Outlet Ground: Available from 3-

prong, 120VAC, power outlets only. To test the

integrity of the ground terminal, use a three-wire

circuit tester with neon lamp indicators, such as

the UL-Listed Ideal Model 61-035, or equivalent,

available at most electrical supply stores.

The panel requires the earth ground

connection for its lightning transient protection

devices.

•

Metal Cold Water Pipe: Use a noncorrosive metal

strap (copper is recommended) firmly secured to the

pipe to which the ground lead is electrically

connected and secured.

Determining the Control’s Power Supply Load

Use the tables that follow to calculate the total current

for the Auxiliary Power, the Alarm Output, and the

Polling Loop. In each table, multiply each device’s

standby and/or alarm current by the number of units

used.

2. In Table 2, enter devices used on Auxiliary Power.

Calculate standby and alarm currents, then add to

get Auxiliary Power current subtotal.

Table 2: Auxiliary Power Current Load

1. In Table 1, enter devices used on the polling loop.

Calculate total current draw on the polling loop.

Total Current

Device

Model #

Device Current X

# of Units

Standby

Alarm

Table 1: Total Polling Loop Current Draw

Polling Loop Device Current # of Units

Total

Auxiliary Power Subtotal

(terminals 6 & 7 – 750mA max.)

Polling Loop Subtotal

(terminals 24 & 25 – 64mA) ✳

✳ The total current cannot exceed 64mA. If total load exceeds

64mA, then a 4297 Loop Extender Module can be used. Note

that the total number of points connected to the panel cannot

exceed 55.

3-25

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

3. In Table 3, enter devices connected to the Alarm

Output. Calculate alarm currents, then add to get

the Alarm Output current subtotal.

4. In Table 4, enter the total calculated subtotals of

all listed outputs from Tables 1 through 3, then add

to get the combined current.

Table 3: Alarm Output Current Load

Table 4: Total VISTA-40 Current Load

Total Current

Device

Model # # of Units

Device Current X

Standby

Alarm

Standby Alarm

Polling Loop Subtotal (see Table 1)

Aux. Power Subtotal (see Table 2)

Alarm Output Subtotal (see Table 3)

XXXXXX

VISTA-40 PCB Current (Includes 2-

wire smoke detector loading on

250mA

330mA

zone 1)

Total Current Load

Alarm Output Subtotal

(terminals 4 & 5 – 1.7A max.)

Determining the Size of the Standby Battery

The cabinet supplied with the control panel can house

batteries of up to 12V, 14AH (two 12V, 7AH batteries

wired in parallel). The VISTA-ULKT kit provides a

cabinet that can house batteries of up to 12V, 17.2AH

and that may be used with this panel. The total

standby current drawn from the auxiliary power and

polling loop outputs combined must be limited to

270mA when 14AH batteries are used; and to 390mA

when 17.2AH batteries are used.

Use Table 5 to determine the required backup battery

capacity and use Table 6 to determine the battery

model number. A dual battery harness is supplied

that allows two batteries to be wired in parallel for

increased capacity.

5. Using the total calculated from Table 4, calculate

the battery capacity required for the installation.

Table 5: Battery Capacity Calculation Table

Calculated

Value

Capacity Formula

DO NOT use Gates batteries (sealed lead-acid

type). These batteries require a different

charging voltage than is supplied by the panel.

Standby

Capacity

For 4-hour standby time:

Total standby current X 4 hours

X 1.4 contingency factor.

Household Fire or Combination

For 24-hour standby time:

Total standby current X 24

hours X 1.1 contingency factor.

Household/Fire/Burglary installations require

the use of a backup battery that is capable of

providing 24 hours of standby time followed by

4 minutes of alarm time. UL1023 Household

Burglary-only installations require the use of a

backup battery that is capable of providing 4

hours of standby time followed by 4 minutes of

alarm time.

Alarm

Capacity

For 4-, 5-, or 15-minute alarm

time:

Total alarm curr.

X 0.067 (4 min)

X 0.250 (15 min)

Total

Add standby and alarm

Capacity capacities

3-26

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3 - Installing the Control

6. Use the Battery Selection Table to select the

appropriate battery for the installation.

7. Connect the battery, referring to Figure 3-29.

Table 6: Battery Selection Table

The standby battery is automatically tested for

10 minutes every 4 hours, beginning 4 hours

after exiting Programming mode. In addition,

entry into the Test mode initiates a battery test.

Capacity Recommended Battery

Comment

4AH

7AH

12AH

Yuasa NP4-12

Yuasa NP7-12

Yuasa NP12-12

Fits in large

mercantile

cabinet only.

14AH

Yuasa NP7-12

Connect two

in parallel.

17.2AH

Yuasa NPG18-12

Fits in large

mercantile

cabinet only.

3-27

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

3-28

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Programming

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Program Modes

The factory-loaded defaults (✳97) enable

keypad addresses 00-03 only. A keypad set to

one of these addresses must be used to

program the system initially.

There are two programming modes for the VISTA-40.

These are the Data Field Program Mode and the #93

Menu Mode. The Data Field Program Mode is where

many system options are programmed. The #93 Menu

Mode is an interactive mode that requires a 2-line

alpha keypad (6139/6160).

Local keypad programming can be disabled

through Compass downloading software. If

this is done, Program mode can only be

accessed via the downloading software.

Entering and Exiting Programming Mode

Enter Programming mode using either method a or b:

Exit the Programming mode by either method a or b:

a. Press [✳] + [9] + [8]. Exiting by this method

prevents the installer code from being used to re-

enter Programming mode. Only method “a” can be

used to re-enter Programming mode.

a. Press both the [✳] and [#] keys at the same time

within 30 seconds after power is applied to the

control.

b. Enter the Installer Code + [8] + [0] + [0] keys.

The factory installer code can be changed once in

the Program mode (field ✳00).

b. Press [✳] + [9] + [9]. Exiting by this method

permits the installer code to be being used to re-

enter Programming mode.

NOTE: The default for the Installer Code is 4140.

Data Field Programming Mode

In the Data Field Program Mode you may access any

field simply by entering either [✳] or [#] + the field

number:

Moving Between Programming Levels

The data fields are grouped into three levels (referred to

as “pages”). The first page is accessed as soon as

Programming Mode is entered.

•

To write or change information in a field press [✳]

+ the field number (✳03).

The second and third pages of data fields are indicated

at the keypad by a 1 and 2, respectively, in front of the

2-digit field address. “ALT PROGRAM MODE” is

displayed along with a “100” or “200,” indicating which

page of program fields is accessed.

•

To read the information in a field press [#] + the

field number (#03).

When the entries for a field are completed, the keypad

beeps three times and advances to the next field.

To access the next level of programming fields, perform

the following steps:

Summary of Data Field Programming Commands

Step

Action

Select partition for programming partition-specific fields

Display the software revision level of the control panel

Enter Menu mode programming

✳91

✳92

✳93

✳94

✳99

Press ✳94.

Press [7] + [XX], where XX = the last two

digits of the program field, and make the

desired entry.

Go to next page of fields

NOTES:

Go back to previous page of fields or exit

Programming Mode with no installer code lockout

Press ✳94 to move to 2^ndpage, (fields 1✳01 - 1✳76);

press ✳99 to move back to 1^stpage.

Exit Programming Mode with Installer Code lockout

✳98

Press ✳94 to move to 3^rdpage (fields 2✳00 - 2✳21); press

✳99 to move back to 2^ndpage

4-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

NOTE: If the number of digits that you enter in a data

field is fewer than the maximum permitted (for

example, a phone number), the keypad displays the last

entry and waits. To proceed, enter [✳] + the next data

field you wish to program.

Entry Errors

•

If an address is improperly entered, the keypad

displays “FC.”

•

If a program entry is improperly entered (for

example, a larger number than is permitted), the

keypad display will go blank.

Programming Partition-Specific Data Fields

In either of the above cases, simply re-enter [✳] + the

correct field number and then enter the correct data.

To program partition-specific data fields once in

Program Mode, do the following:

Step

Action

Programming System-Wide Data Fields

Enter Program Mode: Installer Code + 8 0

Values for some programming fields are system-wide

(global), and some can be different for each partition

(partition-specific).

Press ✳91, which will prompt you for the

partition number desired.

The partition-specific programming fields are

automatically skipped when programming the

global fields. If the system has only 1 partition,

the partition-specific fields are not automatically

skipped.

Enter a partition-specific field number (e.g.,

✳09) to begin programming.

When the first field’s entry is completed, the

next partition-specific field is automatically

displayed. When all partition-specific fields

are programmed, the system returns to the

global programming fields (page 1 fields).

To program system-wide data fields, perform the

following steps:

Step

Action

Repeat this procedure for the other partition.

Enter Program Mode: Installer Code + 8 0 0.

The following display appears:

NOTE: To return to the global program fields before

finishing all fields, enter any global field number.

Programming Partition-Specific Fields

Program Mode

Press ✳91 to select a partition.

✳Fill # View – 00

Enter the partition to be programmed.

If the control has not been programmed before,

enter ✳97 to load factory defaults.

Enter a partition-specific field number and make

entry.

Press [✳] and enter the first field number to be

programmed (for example, ✳00, Installers

Code). Make the desired entry. When the field

is complete, the keypad beeps three times and

advances to the next field. If you do not want to

change the next field, press [✳] and enter the

next field number to be programmed.

Enter any global field number to return to the global

fields at any time.

First Page of fields

(✳00 - ✳90)

To change to the next page of fields, press ✳94.

To return to the previous page of fields, press

✳99.

Press ✳99 or ✳98 to exit Program Mode.

#93 Menu Mode Programming

The #93 Menu Mode is an interactive mode through

which much of the system’s programming is done. In

this mode, there are “question and answer” prompts

that can be accessed once Data Field Program Mode has

been entered. These prompts require a 2-line alpha

keypad (6139/6160).

After programming all system-related programming

fields in the usual way, press #93 while still in

programming mode to display the first choice of the

menu-driven programming functions. Press 0 (NO) or 1

(YES) in response to the displayed menu selection.

Pressing 0 will display the next choice in sequence.

4-2

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Below is a list of the main menus. For details refer to the VISTA-40 Programming Guide.

MAIN MENU

OPTIONS

For programming the following:

ZONE PROG?

•

Zone Number

1 = YES 0 = NO

•

Zone Response Type

Partition Number for Zone

Dialer report code for zone

Input Device Type for zone (whether RF, polling loop, etc.)

Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system.

Same as Zone Programming except:

EXPERT MODE?

1 = YES 0 = NO

•

Done with a minimum number of keystrokes.

•

Can program wireless keys using pre-defined templates.

For entering alpha descriptors for the following:

ALPHA PROG?

1 = YES 0 = NO

•

Zone Descriptors

Installer’s Message

Custom Words

•

Partition Descriptors

Relay Descriptors

For defining the following device characteristics for addressable devices, including keypads, RF

receivers (5881), relay modules (4204), and 4285/4286 VIP Module:

DEVICE PROG?

1 = YES 0 = NO

•

Device Address

•

Device Type

Keypad Options (including Partition assignment)

RF House ID

For defining relay device functions.

RELAY PGM?

1 = YES 0 = NO

For entering voice descriptors for relays to be used with the 4285/4286 VIP Module.

For creating custom word substitutes for VIP Module annunciation.

RLY VOICE DESCR?

1 = YES 0 = NO

CUSTOM INDEX ?

1 = YES 0 = NO

Following is a list of commands used while in the Menu Mode:

#93 Menu Mode Programming Commands

#93

Enters Menu Mode.

Serves as [ENTER] key. Press to have keypad accept entry.

[✳]

[#]

Backs up to previous screen.

Press to answer NO.

Press to answer YES.

Quits Menu Mode and goes back to Data Field Programming Mode, if entered at first prompt of each main menu option.

00, or 000+[✳]

4-4

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Zone Number Designations

The VISTA-40 supports up to 64 zones of hardwire,

polling loop and/or wireless protection, distributed

among up to 2 partitions. The following table lists the

zone numbers and the types of sensors that can be used

with each, and some alternate functions of the zones.

Zone Index

The zones are designated as follows:

ZONE #

RANGE

ZONE

FUNCTION

ACTUAL ZONE

As indicated

01 – 64

Protection

zones

Zone

Function

2-wire Smoke Detectors (if used)

Audio Alarm Verification (if used)

Keyswitch (if used)

70, 88, 89, System

90, 91, &

70:

88:

Bell Supervision

2^ndWireless Receiver –

Supervisory

Zones

not receiving signals

89:

90:

91:

97:

2^ndWireless Receiver –

not talking to control

1^stWireless Receiver –

not receiving signals

1^stWireless Receiver –

not talking to control

Latching-Type Glassbreak Detectors (if used)

Traditional Hardwired Zones

5800 Series Wireless Devices

Polling Loop Devices

✳ + 1 Panic

1-9

1-64

10-64

Polling Loop (short

circuit)

# + 3 Panic

✳ + # Panic

92, 95, 96, Duress and

& 99 Keypad Panics

92:

95:

96:

99:

Duress

Zone Defaults

1 + ✳ panic (A key)

3 + # panic (C key)

✳ + # panic (B key)

Zone #

Zone Type

Zone #

Zone Type

N/A

Supervisory zones should be given a response type of 05

(Trouble by Day, Alarm by Night).

92*

10–64

NOTES: *Zone 92 is the Duress zone. Programming of the

zone response type is not applicable. This zone requires only

the report code programming.

Communication Defaults

*45 PRIMARY FORMAT

*46 LOW SPEED FORMAT (Prim) [0] ADEMCO Low Speed

*47 SECONDARY FORMAT [1] ADEMCO Contact ID

*48 LOW SPEED FORMAT (Sec.) [0] ADEMCO Low Speed

*49 CHECKSUM VERIFICATION [0] [0]

[1] ADEMCO Contact ID

*51 DUAL REPORTING

*52 STANDARD/EXPANDED REPORT FOR PRIMARY

[0] [0] [0] [0] [0] [0]

[0] no

standard

Alarm Rstr Bypass Trbl Opn/Cls Low Bat

*53 STANDARD/EXPANDED REPORT FOR SECONDARY

[0] [0] [0] [0] [0] [0]

standard

No checksum

Primary Secondary

Alarm Rstr Bypass Trbl Opn/Cls Low Bat

*50 SESCOA/RADIONICS SEL.

[0] Radionics

4-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 4 – Programming

Communication Defaults for Zones

ZONE #

1st

2nd

ZONE #

1st

2nd

ZONE #

1st

2nd

ZONE #

1st

2nd

92 (DURESS)

ALARM RST.

TROUBLE

TRBLE. RST

BYPASS

BYP. RST.

Zone Response Type Definitions

Each zone must be assigned a zone type, which defines

the way in which the system responds to faults in that

zone. There are three keypad-activated zones (panic

keys; see note) for each partition, a polling loop

supervision zone, and four RF supervisory zones, two

for each RF receiver installed. Zone types are defined

below.

Type 03: Perimeter Burglary

Provides an instant alarm if the zone is faulted and the

system is armed in the AWAY, STAY, INSTANT, or

MAXIMUM mode.

Assign this zone type to all exterior door and window

zones.

Type 04: Interior, Follower

Type 00: Zone Not Used

Provides a delayed alarm (using the programmed entry

delay time) if an entry/exit zone is faulted first.

Otherwise it produces an instant alarm. It is active

when the system is armed in the AWAY or MAXIMUM

mode, but the MAXIMUM mode eliminates the entry

delay.

Program with this zone type if the zone is not used.

Type 01: Entry/Exit #1 Burglary

Provides entry delay whenever the zone is faulted and

the system is armed in the AWAY or STAY mode. When

the panel is armed in the INSTANT or MAXIMUM

mode, no entry delay is provided. Exit delay begins

whenever the control is armed, regardless of the arming

mode selected. These delays are programmable.

Zones programmed for Interior Follower zone are

automatically bypassed when the panel is armed in the

STAY or INSTANT mode.

Assign this zone type to zones that are used for primary

entry to and exit from the facility.

Assign this zone type to a zone covering an area such as

a foyer, lobby, or hallway through which one must pass

upon entry or exit (to and from the keypad).

Type 02: Entry/Exit #2 Burglary

Type 05: Trouble by Day/Alarm by Night

Provides a secondary entry delay, if the system is

armed in the AWAY or STAY modes and the zone is

faulted. When the panel is armed in the INSTANT or

MAXIMUM mode, no entry delay is provided.

Secondary exit delay begins whenever the control is

armed, regardless of the arming mode selected. These

delays are programmable.

Provides an instant alarm if the zone is faulted and the

system is armed in the AWAY, STAY, INSTANT, or

MAXIMUM mode. During the disarmed state (day), the

system annunciates a latched trouble sounding from

the keypad (and a central station report, if desired).

Assign this zone type to a zone that contains a foil-

protected door or window (such as in a store), or to a

zone covering a sensitive area such as a stock room or

drug supply room. It can also be used on a zone in an

area where immediate notification of an entry is

desired.

Assign this zone type to zones that are used for entry

and exit of the facility and require more time than the

primary entry and exit point. Delay times for this zone

type must be greater than those for zone type 01 (e.g., a

garage, loading dock, or basement door).

4-5

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Type 06: 24-Hour Silent Alarm

Type 20: Arm-STAY (5800 Series devices only)

Sends a report to the central station but provides no

keypad display or sounding. Assign this zone type to a

zone containing an Emergency button.

Causes the system to arm in the STAY mode when the

zone is activated.

Type 21: Arm-AWAY (5800 Series devices only)

Type 07: 24-Hour Audible Alarm

Causes the system to arm in the AWAY mode when the

zone is activated.

Sends a report to the central station and provides an

alarm sound at the keypad and an audible external

alarm. Assign this zone type to a zone containing an

Emergency button.

Type 22: Disarm (5800 Series devices only)

Causes the system to disarm when the zone is

activated.

Type 08: 24-Hour Auxiliary Alarm

Type 23: No Alarm Response

Sends a report to central station and provides an alarm

sound at the keypad only. (No bell output is

provided.) Assign this zone type to a zone an

Emergency button or one containing monitoring devices

such as water sensors or temperature sensors.

Used on a zone when an output relay action is desired,

but with no accompanying alarm (e.g., for access door).

NOTE FOR PANIC KEYS: Keypad panic zones share the same

zone response type for both partitions, but panics may be

individually enabled for each partition.

Type 09: Supervised Fire (Without Verification)

Provides a fire alarm on a short circuit and a trouble

condition on open circuit. A fire alarm produces a

pulsing of the bell output. A zone of this type is always

active and cannot be bypassed.

IMPORTANT! FAULT ANNUNCIATION

Polling loop and RF troubles (zones 88, 89, 90, 91, and 97) report

as trouble conditions only, and as such, should be assigned zone

type 05 if annunciation is desired. See Polling Loop Supervision

and RF System Operation and Supervision in SECTION 3

Installing the Control for more information.

Type 10: Interior with Delay

Provides entry and exit delays (using the programmed

entry and exit delay times) when armed in the AWAY

mode. Provides only exit delay when armed in the

MAXIMUM mode (no entry delay). Delay begins

whenever sensors in this zone are violated, regardless of

whether or not an entry/exit delay zone was tripped

first.

Zones programmed for Interior with Delay are

automatically bypassed when the panel is armed in the

STAY or INSTANT mode.

Assign this zone type to a zone covering an area such as

a foyer, lobby, or hallway through which one must pass

upon entry or exit (to and from the keypad).

Zone Input Type Definitions

Each zone must be assigned an input type, which

defines the where the system will “look” for status of the

zone (RF receiver, polling loop, etc.). Zone input types

are defined below.

Type 05 Unsupervised Button RF (BR)

Select for 5800 Series RF transmitters specifically

designed for this input type. Check the transmitter’s

instructions for proper programming of the input type.

These transmitters send only fault signals. They do not

send low-battery signals until they are activated. The

transmitter may be carried off-premises.

Type 01 Hardwired (HW)

Reserved for the built-in hardwired zones 1-9.

Type 03 Supervised RF (RF)

Type 06 Serial Number Polling Loop (SL)

Select for 5800 Series RF transmitters that will be

supervised for check-in signals. The transmitter must

remain within the receiver’s range.

Select for polling loop devices with a built-in serial

number.

Type 07 DIP Switch Loop (DP)

Type 04 Unsupervised RF (UR)

Select for polling loop devices that use DIP switches for

programming the zone number of the device.

Select for 5800 Series RF transmitters that will not be

supervised for check-in signals. The transmitter may

therefore be carried off-premises.

Type 08 Dip Switch Polling Loop Right Loop (PS)

Select for the second loop of two-zone polling loop

devices (e.g., 4190WH; 4278).

4-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 4 – Programming

Programming for 4100SM

•

1✳40 & 1✳41 Date and Time Set Report Codes

1✳70 Event Log Types (1=enable; 0=disable

1✳71 12/24-Hour Time Stamp (0=12 hr; 1=24 hr)

Programming for Access Control

A user can trigger an access point (i.e., door strike) for 2

seconds by entering User Code + [0].

To program the VISTA-40 for access control, perform

the following steps:

Step

Action

Enter Relay Programming in the #93 Menu

Mode.

Program the relay type as 1, or 2.

For type 1, program the ECP address and

relay number.

For type 2, program the house and unit codes.

Program the relay number in field 1∗76

(partition-specific).

See Relay Programming in the Programming Guide for

a detailed explanation.

4-7

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

4-8

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Data Field Descriptions

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

About Data Field Programming

The following pages list this control’s data fields in numerical order. Field numbers are listed in the left column, followed

by a “Title and Data Entries column, which lists the valid entries for each field. Experienced installers can simply follow

this column when programming the data fields. The “Explanation” column provides explanatory information and special

notes where applicable.

NOTE: Refer to the Programming Guide for the default values. They are not listed in this section.

Use the Programming Guide to record the data for this installation.

Programming Data Fields

Data field programming involves making the appropriate entries for each of the data fields. Start Data Field

programming by entering the installer code + 8 + 0 + 0.

FIELD

TITLE and DATA ENTRIES

EXPLANATION

The Installer Code is a 4-digit code reserved for installation company use.

Installer Code

Enter 4 digits, 0-9

*00

This is the only code that can be used to enter the Program Mode from

the keypad. This code cannot be used to disarm the system if it isn’t used

to arm the system. This code cannot be used to re-enter Program Mode if

Program Mode is exited by the *98 command.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Response Types for Zones 01–08

Response Types for Zones 09–16

Response Types for Zones 17–24

*02

*03

*04

*05

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Response Types for Zones 25–

27, 97, 95, 96, and 99

Entry delay defines the delay time that allows users to re-enter the

premises through a door that has been programmed as an entry delay

door and disarm the system without sounding an alarm. The system must

be disarmed within this period or an alarm will occur.

Entry Delay #1 (partition-specific)

Enter 02-15 multiplied by 15 seconds.

00 = no delay.

*09

NOTE: The delay may not exceed 45 seconds for UL installations.

Exit delay defines the delay period that allows users to leave the premises

through a door that has been programmed as an entry/exit delay door

after arming the system without setting off the alarm.

Exit Delay #1 (partition-specific)

Enter 03-15 multiplied by 15 seconds.

00 = no delay.

*10

*11

Entry Delay #2 is used for a secondary door requiring a longer delay than

those assigned to Entry Delay #1.

Entry Delay #2 (partition-specific)

Enter 02-15 multiplied by 15 seconds.

00 = no delay.

NOTE: The delay may not exceed 45 seconds for UL installations.

5-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

FIELD

TITLE and DATA ENTRIES

EXPLANATION

Exit Delay #2 is used for a secondary door requiring a longer delay than

those assigned to Exit Delay #1.

Exit Delay #2 (partition-specific)

Enter 03-15 multiplied by 15 seconds.

00 = no delay.

*12

NOTE: The delay may not exceed 60 seconds for UL installations.

Defines the length of time the Bell Output and the keypad’s sounder will

sound for all audible alarms.

Alarm Sounder Duration

*13

(partition-specific)

Enter 01-15 multiplied by 2 minutes.

00 = no timeout.

Must be minimum 16 minutes for UL Commercial Burglary installations.

Select the response time for devices connected to zone 9.

Zone 9 Fast/Slow Response

0 = slow 350ms

1 = fast 10ms

*14

*15

The keyswitch requires the use of zone 7 wired loop (zone 7 is no longer

available as protection zone). The fire and panic alarm voltage triggers

(J7) automatically become ARMING and READY status outputs for the

Keyswitch LEDs.

Keyswitch Assignment

Enter 1-2 partition keyswitch is being used.

Enter 0 if the keyswitch is not used.

Openings/closing report as user “0” if enabled in field *40.

If enabled, produces ½-second external alarm sounding (“ding”) at the end

of exit delay (or after kissoff from the central station, if sending closing

reports).

Confirmation of Arming Ding

(partition-specific)

0 = disable

*16

Must be 1 for UL installations.

1 = enable

If enabled, sounding at the keypad (rapid beeping) occurs when AC power

is lost (sounding occurs about 2 minutes after actual AC loss).

AC Loss Keypad Sounding

0 = disable

1 = enable

*17

*19

If enabled, randomizes AC loss reporting between 10 and 40 min. after an

actual AC loss.

Randomize AC Loss Report

0 = disable

1 = enable

If disabled, AC loss reporting about 2 minutes after actual AC loss.

Selecting this option helps prevent an overload of AC loss messages at the

central station during a community blackout.

If a 4285/4286 Voice Module is being used, enter the 2-digit phone code

used to access the system.

VIP Module Phone Code

1-9 = first digit of access code

*20

*21

or # = second digit of access code (enter #

+11 for “∗”, or # +12 for “#”)

Must be disabled for UL installations.

To disable enter 00 for the 1^stdigit

If enabled, there is no timeout of the alarm sounder duration for all fire

zones, regardless of partition, so that fire sounding continues until the

system is reset.

Prevent Fire Timeout

0 = disable (timeout)

1 = enable (no timeout)

If disabled, (timeout) the normal burglary sounder duration (field ✳13)

applies to fire alarms.

If enabled, the keypad panics (zones 995, 996, and 999) may be used in

this partition. There are 3 entries in this field, one for each panic.

Keypad Panic Enables (partition-

*22

*23

specific)

0 = disable

1 = enable

If enabled, allows more than one alarm sounding for a given zone during

an armed period.

Multiple Alarms (partition-

specific)

0 = disable

1 = enable

NOTE: that multiple alarm soundings will not occur more frequently

than allowed by the programmed alarm sounder duration. This has no

impact on the number of communication messages transmitted.

Must be 1 for UL installations.

5-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 5 – Data Field Descriptions

FIELD

TITLE and DATA ENTRIES

EXPLANATION

If disabled, the system monitors the tampers on expansion zones.

Ignore Expansion Zone Tamper

0 = disable (tamper detection)

1 = enable (no tamper detection)

*24

NOTE: Only applicable to certain polling loop sensors with tamper

switches or 5800 Series transmitters.

Must be 0 for UL installations.

If enabled, allows triggering of Output 3 (pin 7) of the J7 header to

include zone response type 8 (24-hr. auxiliary).

Burglary Trigger for Response

*25

*26

Type 8

0 = disable

1 = enable

If enabled, no test report is sent if any other type of report was sent since

the last test report.

Intelligent Test Report

0 = disable

1 = enable

If disabled, test reports are sent at the set intervals, regardless of

whether or not any other report has been sent.

Must be 0 for UL applications.

Test Report Interval

Enter 001-199 for the test report interval in

hours.

If a test report is desired, enter a test code in field *81 and *82. Set first

test report time in field *83.

*27

*28

Maximum Test report interval is 024 for UL installations.

Enter 000 for test reporting.

If enabled, the system, upon power-up, reverts to its status prior to a

complete power loss.

Power-Up in Previous State

0 = disable

1 = enable

If disabled, the system always powers up in a disarmed state.

NOTE: Neither authority level 0 nor 5 can be used to disarm the system

if the control powers up armed.

Must be 1 for UL applications.

If enabled, allows arming of the burglary system in AWAY, STAY,

INSTANT, or MAXIMUM mode by using the [#] key instead of the user

code.

Quick Arm (partition-specific)

*29

*30

0 = disable

1 = enable

NOTES:

When armed, the system reports closing as User 0 if Open/Close reporting

for User #2 (typically a Master level user) was enabled for a given

partition.

If Quick Arm is used, the Installer Code and Authority Level 5 codes

cannot disarm the system.

Select the dialing method for the system

TouchTone or Rotary Dial

0 = disable

1 = enable

If you select TouchTone, make sure the subscriber has requested and is paying for TouchTone service. Note that

whether or not TouchTone dialing for call placement is permitted, communication by the use of DTMF signaling

(ADEMCO High Speed) will still take place. See field 1*33 for TouchTone w/Rotary backup

This field is used to enter up to four 2-digit numbers representing the

prefix needed to obtain an outside telco line. If not required, enter

nothing and proceed to next field.

PABX Access Code

*31

*32

Enter 00-09; B-F (11-15)

Enter a 3- or 4-digit (depending on report format) primary subscriber

account number. Each number requires a 2-digit entry so as to allow

entry of hexadecimal digits (B-F). If a 3-digit account number is to be

used, enter data only in the first 3 locations, and enter * in the fourth

location.

Primary Subscriber’s Account

Number (partition-specific)

Enter 00-09; B-F (11-15)

5-3

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

FIELD

TITLE and DATA ENTRIES

EXPLANATION

Enter the primary central station phone number, up to 17 digits. This is

the phone number the control will use to transmit Alarm and status

messages to the central station. Do not fill unused spaces.

Primary Phone Number

Enter 0-9; #11 for *, #12 for #, #13 for a 2-

second pause.

*33

NOTE: Backup reporting is automatic only if a secondary phone number

is entered.

Enter the secondary phone number, up to 17 digits. The secondary phone

number is used if communication on the primary number is unsuccessful,

or if split/dual reporting is desired. Do not fill unused spaces.

Secondary Phone Number

Enter 0-9; #11 for *, #12 for #, #13 for a 2-

second pause.

*34

NOTE: If this field is programmed, a secondary subscriber account

number (field *90) must also be programmed.

Enter the downloading phone number, up to 17 digits. Do not fill unused

spaces.

Download Phone Number

Enter 0-9; #11 for *, #12 for #, #13 for a 2-

second pause.

*35

*36

NOTE: This field is applicable only if downloading is utilized.

Enter eight digits.

Download ID Number

Make entries as 2-digit numbers as follows:

00=0 01=1 02=2 03=3 04=4 05=5

06=6 07=7 08=8 09=9 10=A 11=B

12=C 13=D 14=E 15=F

NOTE: This field is applicable only if downloading is utilized.

Enabling a function means that you are able to perform that function via

the Compass Downloading software.

Download Command Enables

0 = disable

1 = enable

*37

Functions are as follows: Dialer Shutdown; System Shutdown; Not Used;

Remote Bypass; Remote Disarm; Remote Arm; Upload Program;

Download Program.

For UL installations, all entries must be 0.

Enter two digits for zone that cannot be bypassed by the user.

Prevent Zone XX Bypass

*38

*39

*40

*41

*42

NOTES:

(partition-specific)

Enter a zone number (01-64).

Enter 00 if all zones can be bypassed.

The actions manual bypass, and STAY/INSTANT arming modes cannot

bypass any zone programmed in this field.

If enabled, whenever the Installer Code is used to arm or disarm the

partition, an open/close report is sent to the central station.

Enable Open/Close Report for

Installer Code (partition-specific)

0 = disable

1 = enable

If enabled, whenever the keyswitch is used to arm or disarm the partition,

an open/close report is sent to the central station.

Enable Open/Close report for

Keyswitch

0 = disable

1 = enable

If disabled, end-of-line resistors must be used on zones 2-8.

Normally Closed or EOLR (Zones

If enabled end-of-line resistors cannot be used and only normally closed

devices must be used.

2-8)

0 = disable

1 = enable

Must be 0 for UL installations.

Enter the time the system waits for dial tone before dialing. Applies if

true dial tone is not selected in field *43.

Dial Tone Pause

Enter the wait time for dial tone detection:

0 = 5 seconds; 1 = 11 seconds; 2 = 30

seconds.

Must be 0 for UL installations.

5-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 5 – Data Field Descriptions

FIELD

TITLE and DATA ENTRIES

EXPLANATION

If enabled, the system waits for true dial tone. If no dial tone is detected,

control dials at end of pause programmed in field *42.

Dial Tone Detection

0 = disable

1 = enable

*43

If disabled, the system pauses for seconds entered in field *42, then dials.

NOTE: Disabling may be necessary in high-noise environment telco

networks where noise can be confused with dial tone, resulting in

premature dialing.

Only applicable if using a 4285/4286 VIP Module and/or if station-

initiated downloading will be used.

Ring Detection Count

Enter 00 to disable ring detection.

Enter 01-14 for ring counts of 1-14.

Enter 15 to select Answering Machine

Defeat Mode

*44

NOTES:

Do not enter 00 if a 4285/4286 is installed.

In the Answering Machine Mode, the caller should let the phone ring

once, then hang up, and call again within 30 seconds. The system, upon

hearing one ring followed by nothing, does not answer the first call, but

readies itself to pick up on the first ring of the next incoming call that is

received within 30 seconds (i.e., the downloader calling again).

Must be 00 for UL installations.

Enter the reporting format for the primary telephone number.

Primary Format

*45

*46

*47

*48

*49

0=Low Speed; 1=Contact ID; 2=ADEMCO

High Speed; 3=ADEMCO Express

Enter the low speed format for the primary telephone number.

Enter the reporting format for the secondary telephone number.

Enter the low speed format for the secondary telephone number.

Low Speed Format (Primary)

0 = ADEMCO Low Speed

1 = Sescoa/Radionics

Secondary Format

0=Low Speed; 1=Contact ID; 2=ADEMCO

High Speed; 3=ADEMCO Express

Low Speed Format (Secondary)

0 = ADEMCO Low Speed

1 = Sescoa/Radionics

If enabled, the system for either or both primary/secondary formats sends

a verification digit to validate the message at the receiver without having

to send two message rounds. Selection is valid for 3+1, 4+1, and 4+2

reports.

Checksum Verification

Enter 2 digits, one for the primary and one

for the secondary.

0 = disable

1 = enable

If disabled, selects Radionics, which uses hexadecimal 0-9, B-F reporting.

If enabled, selects Sescoa, which uses only numeric reporting (0-9).

Sescoa/Radionics Select

0 = disable

1 = enable

*50

*51

NOTE: The selection applies to both primary and secondary phone

numbers.

If enabled, all reports are to be sent to both primary and secondary phone

numbers.

Dual Reporting

0 = disable

1 = enable

NOTE: If used with Split Reporting option 1 (1*34), alarms go to both

primary and secondary numbers, while all other reports go to secondary

only. If used with Split Reporting option 2, alarms go to both lines,

open/close and test messages go to secondary only, while all other reports

go to primary.

5-5

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

FIELD

TITLE and DATA ENTRIES

EXPLANATION

This field has six entries as follows: Alarm, Restore, Bypass, Trouble,

Open/Close, Low Battery. If enabled, expanded reports are sent to the

primary phone number if low speed format is selected in field *45.

Standard/Expanded Reporting

*52

Primary

0 = disable

1 = enable

NOTE: Expanded overrides 4+2 format.

This field has six entries as follows: Alarm, Restore, Bypass, Trouble,

Open/Close, Low Battery. If enabled, expanded reports are sent to the

secondary phone number if low speed format is selected in field *47.

Standard/Expanded Reporting

*53

Secondary

0 = disable

1 = enable

NOTE: Expanded overrides 4+2 format.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 01–08

ID Digit for Zones 01–08

*54

*55

*56

*57

*58

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 09–16

ID Digit for Zones 09–16

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

This field has five two-digit entries as follows: Alarm Restore, Trouble,

Trouble Restore, Bypass, and Bypass Restore. Enter the report code 01-15

for each type of report. Enter 00 for no report.

Supervisory and Restore Codes

for Zones 01–16

Enter 00-15.

NOTE: Each report code is the same for zones 01-16. When using 4+2

format, the system uses the ID digit of the zone (fields *55 and *57).

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 17–24

ID Digit for Zones 17–24

*59

*60

*61

*62

*63

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 25–32

ID Digit for Zones 25–32

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

This field has five two-digit entries as follows: Alarm Restore, Trouble,

Trouble Restore, Bypass, and Bypass Restore. Enter the report code 01-15

for each type of report. Enter 00 for no report.

Supervisory and Restore Codes

for Zones 17–32

Enter 00-15.

NOTE: Each report code is the same for zones 17-32. When using 4+2

format, the system uses the ID digit of the zone (fields *60 and *62).

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 33–40

ID Digit for Zones 33–40

Alarm Code for Zones 41–48

ID Digit for Zones 41–48

*64

*65

*66

*67

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

5-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 5 – Data Field Descriptions

FIELD

TITLE and DATA ENTRIES

EXPLANATION

This field has five two-digit entries as follows: Alarm Restore, Trouble,

Trouble Restore, Bypass, and Bypass Restore. Enter the report code 01-15

for each type of report. Enter 00 for no report.

Supervisory and Restore Codes

for Zones 33–48

Enter 00-15.

*68

NOTE: Each report code is the same for zones 33-48. When using 4+2

format, the system uses the ID digit of the zone (fields *65 and *67).

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 49–56

ID Digit for Zones 49–56

*69

*70

*71

*72

*73

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 57–64

ID Digit for Zones 57–64

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

This field has five two-digit entries as follows: Alarm Restore, Trouble,

Trouble Restore, Bypass, and Bypass Restore. Enter the report code 01-15

for each type of report. Enter 00 for no report.

Supervisory and Restore Codes

for Zones 49–64

Enter 00-15.

NOTE: Each report code is the same for zones 49-64. When using 4+2

format, the system uses the ID digit of the zone (fields *70 and *72).

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 87–88

ID Digit for Zones 87–88

*74

*75

*76

*77

*78

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 89–99

ID Digit for Zones 89–99

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

This field has five two-digit entries as follows: Alarm Restore, Trouble,

Trouble Restore, Bypass, and Bypass Restore. Enter the report code 01-15

for each type of report. Enter 00 for no report.

Supervisory and Restore Codes

for Zones 87–99

Enter 00-15.

NOTE: Each report code is the same for zones 17-32. When using 4+2

format, the system uses the ID digit of the zone (fields *75 and *77).

This field has eight entries, one for each zone type. Select the zone types

that will send Restore reports.

Zone Type Restores for Zone

*79

*80

*81

Types 1-8

0 = disable

1 = enable

This field has two entries, one for each zone type. Select the zone types

that will send Restore reports.

Zone Type Restores for Zone

Types 9 and 10

0 = disable

1 = enable

This field has ten two-digit entries as follows: Close, Open Low Battery,

Low Battery Restore, AC Loss, AC Restore, Test, Power-up, Cancel, and

Program Tamper. Enter the report code 01-15 for each type of report.

Enter 00 for no report.

Non-Alarm Report Codes (First

Digit

Enter 00-15.

5-7

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

FIELD

TITLE and DATA ENTRIES

EXPLANATION

This field has ten two-digit entries as follows: Close, Open, Low Battery,

Low Battery Restore, AC Loss, AC Restore, Test, Power-up, Cancel, and

Program Tamper. Enter the report code 01-15 for each type of report.

Enter 00 for no report.

Non-Alarm Report Codes

(Second Digit

Enter 00-15.

*82

Enter the day and time that the first Test report shall be transmitted.

Enter 00 in all locations if the Test report is to be sent immediately upon

exiting. Enter 00 in the day location if the report is to be sent at the next

occurrence of the time that is set.

First Test Report Time

Enter 00-07 the for day (01 = Monday)

Enter 00-23 for the hour

*83

*84

*85

*86

Enter 00-59 for the minutes

This option limits the number of messages (alarms or troubles) sent for a

specific zone in an armed period.

Swinger Suppression (partition-

specific)

Enter 01-15.

Must be 00 for UL installations.

Enter 00 for unlimited reports

This field has four entries as follows: Zone 95, 96, 99, and Duress. Enable

for each partition that the panics and duress reporting is desired.

Enable Dialer Reports for Panics

& Duress (partition-specific)

0 = disable

NOTE: Non-zero report code must be assigned to zone 92 to enable

Duress reporting.

1 = enable

Entering 1 allows a single 4208 to be set to zone numbers 10-17, but

precludes the use of any other polling loop devices.

Entering 0 allows all other configurations, such as no 4208, more than

4208 Module Zone Assignment

0 = other configurations

1 = 10-17 only

one 4208, or other polling loop expansion present.

4208 Zone #s available when:

When *86 = 1 4208 DIP switches must be set to:

*86 = 1

10-17

*86 = 0

10-16

With word OFF

sw 2 = ON

With word ON

sw 2 = OFF

sw 3 = OFF

sw 4 = OFF

sw 5 = ON

Precludes use 17-24

of any other

sw 3 = ON

25-32

sw 4 = ON

polling loop

33-40

sw 5 = OFF

expansion

41-48

49-56

57-64

Select the type of warning for the entry delay period.

Entry Warning (partition-specific)

0 = 3 short beeps

1 = slow continuous beeps

*87

*88

Select the delay, if any, for burglary alarm communications.

Burglary Alarm Communicator

Delay (partition-specific)

0 = no delay

Must be 0 for UL installations.

1 = 16-second delay

Select the time when restore reports are sent after an alarm.

Restore Report Timing

0 = instant

1 = after bell timeout

*89

*90

Must be 2 for UL installations.

2 = when system is disarmed

Enter a 3- or 4-digit (depending on report format) secondary subscriber

account number. Each number requires a 2-digit entry so as to allow

entry of hexadecimal digits (B-F). If a 3-digit account number is to be

used, enter data only in the first 3 locations, and enter * in the fourth

location.

Secondary Subscriber Account

Number (partition-specific)

Enter 00-09; B-F (11-15)

NOTE: This field must be programmed if a secondary phone number is

used (field *34). This account number can be the same as the primary

account number.

5-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 5 – Data Field Descriptions

FIELD

TITLE and DATA ENTRIES

EXPLANATION

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Response Types for Zones 28–32

1*01

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Response Types for Zones 33–40

Response Types for Zones 41–48

Response Types for Zones 49–56

Response Types for Zones 57–64

Response Types for Zones 87–91

RF Transmitter Low Battery

1*02

1*03

1*04

1*05

1*09

1*28

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Skip this field. Use #93 Menu Mode, Zone Programming to program the

response types. Refer to the Programming Guide for details.

Select when the RF transmitter low-battery condition should display and

audible beep annunciate on the keypad.

Sound

Must be 1 for UL installations.

0 = disarmed state only

1 = both armed and disarmed states

If enabled, the system sends a Trouble message for RF transmitter low-

battery condition to the central station.

RF Transmitter Low Battery

1*29

1*30

Reporting

0 = disable

1 = enable

NOTE: The Trouble message will be sent for a transmitter supervision

failure, independent of this selection.

Must be 1 for UL.

Select the check-in monitoring interval for the RF receiver(s).

RF Receiver Supervision Check-

in Interval

Enter 02-15 times 2 hours (4-30 hours).

00 = disable receiver supervision.

Failure of a receiver to receive any RF signal within the time entered

results in the activation of the response type programmed for zone 990 for

the first receiver and zone 988 for the second receiver and their related

communication reports.

Maximum is 2 (4 hr) for UL installations.

Select the check-in monitoring interval for the RF transmitters.

RF Transmitter Check-in Interval

Enter 02-15 times 2 hours (4-30 hours).

00 = disable transmitter supervision.

1*31

Failure of an individual transmitter to send a supervision signal within

the time entered will result in a trouble response and related

communication report.

Maximum is 2 (4 hr) for UL.

If enabled, the system reverts to rotary dialing if communicator is not

successful in dialing using TouchTone DTMF on first attempt.

TouchTone with Rotary Backup

1*33

1*34

0 = disable

1 = enable

Select the type of split reporting for system communication.

Communicator Split Reporting

0 = Split Reporting disabled

NOTE: See *51 for split/dual reporting combinations.

1 = Alarm, Alarm Restore, and Cancel

reports to primary, all others to secondary

2 = Open/Close and Test reports to

secondary, all other reports to primary

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 65–72

1*35

5-9

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

FIELD

TITLE and DATA ENTRIES

EXPLANATION

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

ID Digit for Zones 65–72

1*36

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

Alarm Code for Zones 73–80

ID Digit for Zones 73–80

1*37

1*38

1*39

Skip this field. Use #93 Menu Mode, Zone Programming to program the

report codes. Refer to the Programming Guide for details.

This field has five two-digit entries as follows: Alarm Restore, Trouble,

Trouble Restore, Bypass, and Bypass Restore. Enter the report code 01-15

for each type of report. Enter 00 for no report.

Supervisory and Restore Codes

for Zones 65–80

Enter 00-15.

NOTE: Each report code is the same for zones 17-32. When using 4+2

format, the system uses the ID digit of the zone (fields *75 and *77).

This field has two two-digit entries as follows: Arm STAY, and Time/Date

set or Event Log Reset. Enter the report code 01-15 for each type of

report. Enter 00 for no report.

Arm Stay and Time Set Report

Codes (First Digit)

Enter 00-15.

1*40

1*41

1*43

This field has two two-digit entries as follows: Arm STAY, and Time/Date

set or Event Log Reset. Enter the report code 01-15 for each type of

report. Enter 00 for no report.

Arm Stay and Time Set Report

Codes (Second Digit)

Enter 00-15.

If enabled, backlighting for the keypad display remains on at all times.

Otherwise the backlighting comes on when a key is pressed.

Permanent Keypad Display

Backlighting (partition-specific)

0 = disable

1 = enable

NOTE: When a key is pressed, display backlighting turns on for all

keypads in that partition.

If enabled, when more than 40 key depressions are received without a

valid sequence (arm, disarm, etc.), the control panel disables the wireless

keypad. The inhibit is removed once a valid key sequence is received from

a wired keypad.

Wireless Keypad Tamper Detect

1*44

1*45

0 = disable

1 = enable

If enabled, the system produces slow beeping from the keypads during

exit delay and reverts to rapid beeping during the last 10 seconds of the

exit delay.

Exit Delay Sounding (partition-

specific)

0 = disable

1 = enable

NOTE: The duration of the beeping is the programmed value of field *10

regardless of which entry/exit zone is used to exit the premises.

Select the mode for output 1 on the J7 triggers.

NOTES:

Auxiliary Output Mode

0 = ground start output.

1 = open/close trigger.

2 = keypad sounds at an auxiliary sounder.

3 = AAV module.

1*46

Only one of the options may be active within the system.

Open/close trigger is produced only when both partitions are armed.

Keypad sounds apply only to the partition enabled in field *15.

If enabled, the system produces chime annunciation on the external

alarm sounder.

Chime on External Siren

(partition-specific)

0 = disable

1*47

1*48

1 = enable

Select the partition in which RF keypad is used.

Wireless Keypad Assignment

0 = none

1-8 = partition number

5-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 5 – Data Field Descriptions

FIELD

TITLE and DATA ENTRIES

Suppress Transmitter

Supervision Sound

0 = disable

EXPLANATION

If enabled, no trouble soundings occur on the keypad for transmitter

check-in failures.

1*49

Must be 0 for UL.

1 = enable

If enabled, Cancel reports are sent when the system is disarmed after an

alarm, regardless of how much time has gone by.

Send Cancel If Alarm + Off

(partition-specific)

0 = disable

1*52

If disabled, Cancel reports are sent within Bell Timeout period only.

1 = enable

NOTE: This option must be enabled so Cancel reports are always sent.

Select whether a callback from the control panel is required for

downloading.

Disable Download Callback

0 = callback required

1 = no callback required

1*53

1*57

Must be 0 for UL installations.

If enabled, the system arms/disarms in accordance with the button’s

user’s global arming settings.

Enable 5800 RF Button Global

Arm

0 = disable

1 = enable

If enabled, allows the RF button user to force a bypass of all faulted zones

when arming the system.

Enable 5800 RF Button Force

1*58

Arm

0 = disable

1 = enable

NOTE: When attempting to arm the system, the keypad beeps once after

the button is pressed if any faulted zones are present. The user should

then press the button again within 4 seconds to force-bypass those zones

and arm the system.

If enabled, zone 5 is used for 2-way audio (AAV).

Must be 0 for UL installations.

Zone 5 Audio Alarm Verification

1*60

1*70

1*71

0 = disable

1 = enable

NOTE: Zone 5 cannot be used as protection zone.

This field has five entries as follows: Alarm, Check, Bypass, Open/Close,

and System. If enabled, the system logs those events into the event log.

Event Log Types

0 = disable

1 = enable

Select the type of time stamping for the event log.

12/24 Hour Type Stamp Format

0 = 12-hour

1 = 24-hour

This is used for Relay Programming in the #93 Menu Mode Programming

relay command “56.”

Relay Timeout XXX Minutes

1*74

1*75

1*76

Enter 000-127 times 2 minutes (000-254).

This is used for Relay Programming in the #93 Menu Mode Programming

command “57.”

Relay Timeout YYY Seconds

Enter 000-127 seconds.

If enabled, the assigned relay closes for 2 seconds when the user enters

his code and presses 0.

Must be 00 for UL installations.

Access Control Relay (partition-

specific)

01-08 = relay number

00 = relay not used.

Enter the number of partitions used in the system.

Enter the months (00-12) in which daylight saving time starts and ends.

Number of Partitions

2*00

2*01

Enter 1-2.

Daylight Saving Time Start/End

Enter 00, 00 if daylight saving time does not apply to the user’s region.

Standard setting for U.S. is 04,10.

Month

0 = disable

1 = enable

5-11

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

FIELD

TITLE and DATA ENTRIES

EXPLANATION

Enter the start and end weekends for daylight saving time as follows:

1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next to last; 7=third from

last. Standard setting for U.S. is 1,5.

Daylight Saving Time Start/End

2*02

Weekend

0 = disable

1 = enable

This field has two 2-digit entries. Enter the number user codes for each

partition. The total number of user codes cannot exceed 70 for the system.

Enter 01 for an unused partition.

Number of Codes per Partition

2*17

2*18

Enter 01-69

NOTE: The installer code is automatically assigned to each partition

regardless of whether that partition has been enabled.

If enabled, this partition can be accessed from another partition’s keypad

using the GOTO command.

Enable GOTO for this Partition

(partition-specific)

0 = disable

1 = enable

If enabled, the normal keypad display will include a partition number and

four-digit descriptor.

Use Partition Descriptor

0 = disable

1 = enable

2*19

2*20

If enabled, the J7 triggers function for this partition.

Enable J7 Triggers for Partition

(partition-specific)

0 = disable

1 = enable

There are three entries in this field as follows: Fire, Burglary/Audible

Panic, Silent Panic/Duress.

Supervision Pulses for LRR

0 = disable

1 = enable

2*21

If enabled, causes the control to send periodic short pulses on the J7 radio

triggers to the LRR. The LRR uses these pulses to determine that its

connection to the control is still intact.

Must be 1 for UL installations.

5-12

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Downloading Primer

(Remote Downloading is not a UL Listed feature)

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

General Information

Access Security

Downloading allows the operator to remotely access,

program, and control the security system over normal

telephone lines. Anything that can be done directly

from the keypad can be done remotely, using the

COMPASS downloading software. To communicate

with the control panel, the following is required:

The following four levels of protection guard the control

against compromise while it is being accessed from a

remote location:

1. Security code handshake: The subscriber’s account

number as well as an 8-digit ID number (known

only to the office) must be matched between the

control and computer.

1. IBM PC-compatible 486 33MHz PC or better with

30 MB of available hard disk space and at least

8MB of RAM (12MB is preferred). Windows 3.X,

Windows 95, 98, or Windows NT.

2. Hang-up and callback: The control panel “hangs

up” and calls the computer back at the pre-

programmed number only if the security codes

match.

2. One of the following modems:

•

ADEMCO CIA

3. Data encryption: All data that is exchanged

between the computer and control is encrypted to

reduce the possibility of anyone “tapping” the line

and corrupting data.

Hayes Smartmodem 1200 (external: level 1.2 or

higher; internal: level 1.1 or higher)

•

Hayes Optima 24 + Fax 96 external

Hayes Optima 336

4. Operator access levels: Operators may be assigned

various levels of access to the downloader, each

having its own log-on code. The access levels allow

the operators read/write capabilities of the

customers’ account information. For a detailed

explanation of the access levels, see the

BizComp Intellimodem 1200 w/volume

BizComp Intellimodem 2400

Other brands are not compatible, even if claimed to

be 100% compatible.

3. COMPASS DOWNLOADING software available on

CD ROM with a complete User’s Manual. It may

also be downloaded from the Honeywell web page.

The web address is www.honeywell.com/security.

downloading software User Manual.

NOTES:

•

Each time the control panel is accessed

successfully, a Callback Requested report is sent to

the central station, if Opening reports are

programmed.

Internal modems must have a 4-position DIP

switch. Modems with a 6-position DIP switch

will not work.

•

When the system is downloading, the keypad

displays “MODEM COMM.”

After each download or save, an automatic time

stamp is done, to indicate the last download (or

save) and the operator ID number.

•

A complete hard copy of each individual account

can be obtained by connecting a printer to the

computer. Refer to your computer Owner’s Manual

or contact your dealer for printer recommendations.

6-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Getting On-Line with a Control Panel

At the protected premises, the control panel must be

connected to the existing telephone line (refer to

SECTION 3: Installing the Control). No programming

of the panel is required before downloading to an initial

installation unless you are performing an unattended

download.

To download a control without programming any

information, perform the following steps:

Step

Action

Enter the Installer Code + [#] + [5]. The

panel temporarily enables a ring count of 5

and sets the Download Callback option to “1”

(callback not required).

When establishing a connection between the computer

and the control panel, the following occurs:

From the computer, call the panel using the

downloader software set to “First

Communication” Mode.

Stage

What Happens

The computer calls up the control panel.

(The phone number for each customer must

be entered into the customer’s account file

on the computer.)

The downloader establishes a session with no

callback. The panel information can then be

downloaded.

The control panel answers the phone call at

the pre-programmed ring count and executes

a handshake with the computer.

On-Line Control Functions

The following functions can be performed while on-line

with a control panel (see field *37):

The computer sends a request for callback to

the control, unless callback is not required.

•

Arm the system in the AWAY Mode; disarm the

system

The panel acknowledges the request and

hangs up. During the next few seconds, the

control processes the request, making sure

certain encrypted information received from

the computer matches its own memory.

•

Bypass a zone

Force the system to accept a new program

download

•

Shut down communication (dialer) functions (for

nonpayment of monitoring fees in an owned

system)

Upon a successful match, the control panel

seizes the phone line and calls the computer

back, unless callback is not required. (The

phone number to which the computer’s

modem is connected must be programmed

into the control field ✳35.)

•

Shut down all security system functions (for

nonpayment for a leased system)

Inhibit local keypad programming (prevents

takeover of your accounts)

The computer answers, usually by the

second ring, and executes a handshake with

the panel.

Leave a message for customer

NOTE: Messages sent to the control panel from the

downloader will be viewable at ALL partitions.

The panel then sends other default

information to the computer. If this

information matches the computer’s

information, a successful link is established.

The system is now “on-line” with the

computer.

•

Command the system to upload a copy of its

resident program to the office

Read: arming status, AC power status, list of

faulted zones, list of bypassed zones, 100 event log,

list of zones currently in alarm, list of zones

currently in trouble, and ECP equipment list

•

Set the real-time clock

Alarms and Trouble responses and reports are

disabled during actual uploading or

downloading sessions.

6-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 24 - Downloading Primer

Direct-Wire Downloading

The VISTA-40 can be downloaded without using a

modem or telephone line by using a 4100SM Serial

Module and Compass Downloading Software. The

direct-wire downloading connection is to be temporary,

and is not part of the permanent installation. Direct-

wire downloading is meant as a tool for the installer

during the installation process.

Connector J8 on the main PC board (see the Summary

of Connections diagram on the inside back cover of this

manual) is intended to be interfaced to either a local

serial printer (see SECTION 3:Installing the Control) or

a computer. Make connections to a computer as shown

below. Note that the violet wire connection for a

computer differs from that used when connecting

a serial printer.

The connections between the control and the

4100SM are different than those shown in the

4100SM Installation Instructions. See Figure 6-

1 for the correct connections. In addition, in

place of the green wire, referred to in step 2 of

the “IN CASE OF DIFFICULTY” section of the

4100SM Instructions, use the violet wire

instead.

Figu r e 6-1: Dir ect-Wir e Down loa d in g Con n ection s

Telco Handoff

Telco handoff is another method of getting on-line with the downloader. The installer or customer enters the User Code

+ [#] + [1], while on the phone line with the computer’s modem phone line. The customer will get cut-off and the panel

and download computer will establish a connection.

6-3

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

6-4

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Setting the Real-Time Clock

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

General Information

Use a 6139/6160 alpha keypad to set the real-

time clock, or set the clock via the downloader

software. Only users with Installer or Master

authority level can set the clock.

This system provides a real-time clock, which must be

set in order for the system’s event log to keep track of

events by time and date.

Setting the Time and Date

To set the real time clock, perform the following steps:

Step

Action

Enter Installer or Master Code + [#] 63.

Typical display shows:

TIME/DATE –– THU

12:01 AM

01/01/90

The day of the week is automatically

calculated based on the date entered. Time

and date entries are made by simply entering

the appropriate hour, minute, month, day

and year.

Press [✳] to move the cursor to the right of

the display, to the next position.

Press [#] to move the cursor to the left of the

display, to the previous position.

Enter the correct hour. Then press [✳] to

move to the “minutes” field.

Enter the correct minutes. Press [✳] to move

to the AM/PM position.

Press any key 0-9 to change AM to PM, or PM

to AM. Press [✳] to move cursor to the

“month” field position.

Enter the correct month using a 2-digit entry.

Press [✳] to move cursor to the “day” field

position.

Enter the correct day using a 2-digit entry.

Press [✳] to move cursor to the “year” field

position.

Enter the correct year.

Press [✳] to continue.

7-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

7-2

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

User Access Codes

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

General Information

The VISTA-40 allows a total of 70 security access codes

to be allocated. Each security access code is identified

by a user ID number. A maximum of 69 user codes may

be assigned to any one of the partitions. The installer

code is automatically assigned to both partitions

regardless of whether both partitions are used.

User code number 2 must be programmed in

order for the Quick Arm feature to function.

Open/Close reporting for Quick Arm is enabled if

User 2 is enabled for Open/Close and reports as

User 0.

The Quick Arm feature can also be programmed

(partition-specific program field *29). The Quick Arm

feature allows the user to arm the system by pressing

the [#] key instead of the security code. The security

code must always be entered to disarm the system.

User Codes & Levels of Authority

Each user of the system can be assigned a level of

authority, which authorizes the user for certain system

functions. A user can have different levels of authority

within different partitions

Use the “View Capabilities” keypad function (User

Code + [✳] + [✳]) to view the partitions and authority

levels for which a particular user is authorized. These

levels are described below.

Level 0: Installer (User 1) Code

Level 2: Manager Codes

•

Programmed in field *00 (default = 4-1-4-0).

Installer Open/Close reporting selected in field *39.

•

Can perform all system functions (arm, disarm,

bypass, etc.) programmed by Master.

•

Can perform all system functions (arm, disarm,

bypass, etc.), but cannot disarm if armed by

another code (or by Quick Arm).

•

May add, delete, or change other users of the

system below this level (Manager cannot assign

anybody a level of 0, 1, or 2).

•

Can add, delete, or change all other codes, and can

select Open/Close reports for any user.

Is the only code that can be used to enter program

mode. The Installer Code can be prevented from re-

entering the Program Mode by exiting using ∗98.

Must program at least one Master Code during

initial installation. Master Codes are codes

intended for use by the primary user(s) of the

system.

•

May change his own code.

Open/Close reporting is automatically the same as

that of the Manager who is adding the new user.

Levels 3-5: Operator Codes

•

Can operate a partition, but cannot add or modify

any user code (see table below).

•

Level Title

Functions Permitted

Arm, Disarm, Bypass

Arm, Disarm

Operator A

Level 1: Master Codes

Operator B

Operator C

•

Can perform all normal system functions.

Can be used to assign up to 68 lower-level codes,

which can be used by other users of the system.

Cannot assign anybody a level of 0 or 1.

May change his own code.

Can add, delete, or change Manager or Operator

Codes. Each user’s code can be individually

eliminated or changed at any time.

Arm, Disarm only if armed with

same code

•

Operator C (sometimes known as the Babysitter

Code) cannot disarm the system unless the system

was armed with that code. This code is usually

assigned to persons who may need to arm and

disarm the system at specific times only (e.g., a

babysitter needs to control the system only when

babysitting).

•

Open/Close reporting is automatically the same as

that of the Master who is adding the new user.

8-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Level 6: Duress Codes

Duress Reporting Note: A non-zero report

code for zone 92 (duress) must be programmed,

and partition-specific field *85 duress location

enabled, to enable Duress reporting.

•

Sends a silent alarm to a central monitoring station

if the user is being forced to disarm (or arm) the

system under threat (system must be connected to

a central station).

•

The Duress report-triggering logic activates on the

5th key depression (such as OFF), not the 4th key

depression (last digit of code). Duress reports are

not triggered if the 5th key is a [*], such as when

you perform a GOTO or view the capabilities of a

user.

•

When the system’s Auxiliary Voltage Triggers are

connected to another communication’s media

(Derived Channel/Long Range Radio), note that

duress is signaled on the same trigger that signals

silent panic (whereas duress has its own unique

report when digitally communicated).

•

Assigned on a partition-by-partition basis, and can

be any code or codes desired.

Open/Close Reporting Note: When a user is added,

the system prompts for Open/Close reporting capability

only if the installer is adding the new user. When a

Master or Manager adds a new user, the new user’s

Open/Close reporting is the same as that of the Master

or Manager who is adding the user. If Open/Close

reports are required to be selectable by the Master or

Manager, the Installer should assign two Master or

Manager user codes: one with Open/Close reporting

enabled, and one without.

General Rules on Authority Levels and Changes

The following rules apply to users when making modifications

within the system based on the user code authority levels:

•

Master Codes and all lower-level codes can be used

interchangeably when performing system functions within a

partition (a system armed with a user’s temporary code can

be disarmed with the Master Code or another user’s

temporary code), except the Operator Level C Code

described above.

•

A user may not delete or change the user code of the SAME

or HIGHER authority than that which he is assigned.

Note that Open/Close reporting of Quick Arm is enabled

if User 02 is enabled for Open/Close reporting, and that

Quick Arm reports as User 00. In order for Quick Arm

reports to be sent for all partitions, User 02 must have

authority and Open/Close must be enabled for all

partitions. If a code with access to all partitions is not

desired, it is suggested that user 02 be assigned

authority level 5 in all partitions, and that the code be

kept secret. Authority level 5 cannot disarm the system

unless armed by that user.

A user (levels 0, 1 and 2 only) may only ADD users to a

LOWER authority level.

A user may assign other users access to only those

partitions to which he himself has access.

A user code can be DELETED or CHANGED only from

within the partition it was created in.

User numbers must be entered in 2-digits. Single-digit user

numbers must, therefore, always be preceded by a “0” (e.g.,

03, 04, 05, etc.). Make sure the end user understands this

requirement. Temporary codes are entered as 4-digit

numbers.

ADEMCO Contact ID format is capable of

reporting Users 01-70 uniquely. If any other

report format is used, only user numbers 01 –

15 can uniquely report to the central station.

Users 16 – 70 will report as User 15.

Multiple Partition Access

Each user is programmed for a primary (home)

partition. A user can also be given access to operate one

or both partitions. Within each partition, each user

may be programmed to have different levels of

authority. For example, User 03, the VP of

Engineering, could be assigned to work within the

Engineering Department (Partition 1) of ABC

Manufacturing. Because he needs the full capabilities

in his area, he is assigned as a MASTER with Level 1

authority.

The control automatically assigns him the same user

number within Partition 2.

EXAMPLE OF MULTIPLE PARTITION ACCESS

Part 1

Part 2

User 3

Level 1

Master

User 3

Level 4

Oper B

In the above example, User 3 has MASTER authority in

Partition 1 and OPERATOR B authority in Partition 2.

His user number is the same for both partitions.

He must also be able to gain access to the

manufacturing area (Partition 2) on an emergency

basis. You can set this up easily by requesting that he

also be assigned to Partition 2, with a level of authority

set lower, such as Level 4 (OPERATOR Level B).

8-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 9 – User Access Codes

Adding a Master, Manager, or Operator Code

†

During user code entry, normal key

Enter Installer Code + [8] + new user no. (02-69) +

new user’s code

depressions at other keypads in a partition are

ignored. However, panic key depression

causes an alarm and terminates user entry.

†

Or Master or Manager Code, but the code must be a

higher level of authority than the code being changed

(e.g., a Manager Code can add an Operator-level Code,

but cannot add a Master or another Manager Code).

Keypad prompts for the authority level for this user.

PROMPT

EXPLANATION

Enter the level number as follows:

1 = Master

User Number = 03

Enter Auth. Level

2 = Manager

3 = Operator Level A

4 = Operator Level B

5 = Operator Level C

6 = Duress

Keypad then prompts for Open/Close reporting option for this user.

Press 0 (NO) or 1 (YES), depending on whether or not arming/disarming by this user will trigger Opening

and Closing reports. This prompt appears only if the Installer Code is used to add a user.

Open/Close Rep.?

0 = NO , 1 = YES

If a 5800 Series button transmitter has been enabled for arming/disarming functions, and is not assigned to

a user, this prompt appears. Press 0 (NO) or 1 (YES).

RF Button ?

0=NO , 1=YES

If you answered “yes” to the RF button question, the zone number for the button is requested. Enter any

one of the zone numbers assigned to the button transmitter as AWAY, STAY, or DISARM. The system then

assigns all buttons of the transmitter to this user number.

Enter Button ZN #

(01-63)

Press 0 (NO) if the user is to have access to this partition only. Press 1 (YES) if the user is to have access

to more than one partition. If NO, the program exits this mode. If YES, the keypad prompts for the Global

Arm option for this user.

Multi-Access ?

0 = NO , 1 = YES

Press 0 (NO) or 1 (YES), depending on whether this user will be allowed to arm more than one partition via

Global Arm prompts.

Global Arm ?

0 = NO , 1 = YES

The keypad now prompts for the user’s access to the next partition.

Press 0 (NO) or 1 (YES), depending on whether this user will have access to the displayed partition

number. If NO, the keypad displays this prompt for the next partition number in sequence.

Part. 2 – SHOP ?

0 = NO , 1 = YES

If YES, the keypad prompts for the following:

•

User’s authority level in the displayed partition (see Authority Level prompt above).

Open/Close option for this user in the displayed partition (see Open/Close prompt above).

Global Arm option for this user in the displayed partition (see Global Arm prompt above).

When all partitions have been displayed, the keypad will scroll through all partitions to which access has

been assigned, and will display the user number, authority level, open/close and global arm options that

were programmed for each partition to which the user was granted access. See next prompt.

Note that the “G” following the authority level indicates that the global arm feature is enabled for this user in

the displayed partition, and that the period at the end of the second line indicates Open/Close reporting is

enabled for this user in the displayed partition. The “ ” indicates the partition from which the user may be

changed or deleted.

Part. 1 A0 WHSE

User 03 Auth=3G.

8-3

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Changing a Master, Manager, or Operator Code

Enter Installer Code + [8] + new user no. (02-69) + new user’s code

Or Master or Manager Code, but the code must be a higher level of authority than the code being changed (e.g. a

Manager Code can add an Operator-level Code, but cannot add a Master or another Manager Code).

PROMPT

EXPLANATION

The system detects that the user number is already assigned, and prompts if this is a new user.

Press 0 (NO).

User Number = 03

NEW USER?

The system then confirms that the change is allowed based on authorization level.

Adding an RF Key to an Existing User

To add an RF key to an existing user, or to change a user’s global arm option, first delete that user’s code, then re-add

the user code as described in the “Adding a Master, Manager, or Operator Code” paragraph.

Deleting a Master, Manager, or Operator Code

Enter your code + [8] + new user no. (02-69) + your code again

Or Master or Manager Code, but the code must be a higher level of authority than the code being changed (e.g. a

Manager Code can add an Operator-level Code, but cannot add a Master or another Manager Code).

PROMPT

EXPLANATION

The system prompts to confirm that you want to delete this user. Press 0 (NO) or 1 (YES).

OK TO DELETE 03?

If you answer “yes,” that user’s code is removed from all partitions to which it was assigned, and all

authorization levels and other information about that user are deleted. Note: A user can be deleted only by

a user with a higher authority level. A user cannot delete himself.

0=NO

1=YES

A user code can be deleted only from the partition through which it was entered. If an attempt is made to

delete from another partition, the message “User [XX] Not Deleted” is displayed.

Exiting the User Edit Mode

Press either [7] or [#], or don’t press any key for 10 seconds.

8-4

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Testing the System

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Battery Test

When AC power is present, the VISTA-40 runs a brief

battery test every 4 hours to determine if there is a

battery connected.

It also sends a Low Battery report to the central station

(if programmed). The keypad is cleared by entering any

security code + OFF, and a Restore report is sent to the

central station if the situation has been corrected.

If the VISTA-40 finds that the battery voltage is low

(less than approximately 11.5V), it initiates a keypad

“SYSTEM LOBAT” display and a rapid keypad beeping

sound.

Dialer Test

The VISTA-40 may be programmed to automatically

transmit test reports to a central station at intervals

ranging from once per hour to once per 199 hours (field

✳27).

UL requires the test report to be transmitted at least

once every 24 hours. The system can be programmed to

send the first report at any time of the day, or on any

day of the week (field ✳83).

Burglary Walk-Test (Code + [5] TEST)

This test causes the system to sound keypad beeps in

response to faults on zones for the purpose of allowing

proper zone operation to be checked without triggering

alarms. This test can be activated by any-level user by

entering the corresponding security code and pressing

TEST while the burglary portion of the system is

disarmed. UL requires that this test be conducted on a

weekly basis.

Open and close each protected door and window in turn.

Each action should produce 3 beeps from the keypad.

Walk in front of any motion detectors. Listen for three

beeps when the detector senses movement.

The keypad displays the zone number and alpha

descriptor while a door or window remains open or

while a detector remains activated. The system

automatically issues a Zone 8 Glassbreak Detector

Power Reset about 10 seconds after it finds a fault on

this zone, to allow faulted detectors to be reset.

When this test is first entered, the system activates the

alarm output for 3 seconds. The system sends a test

message to the central station. The keypad displays

“Test in Progress” and sounds a single beep every 15

seconds while the test remains active.

To end this test, enter any security code and press OFF.

Armed Burglary System Test

To perform an armed burglary test, proceed as follows:

Alarm messages are sent to the central station

during the armed system tests. Notify the

central station that a test will be in progress.

Step

Action

Notify the central station that a test of the

system is being performed.

Arm the system.

A display of “COMM. FAILURE” indicates a

failure to communicate (no kissoff by the

receiver at the central station after the maximum

number of transmission attempts is tried). If this

occurs, verify that the phone line is connected,

the correct report format is programmed, etc.

Fault one or more zones.

Silence alarm sounder(s) each time by

entering the code and pressing OFF.

NOTE: The system must be rearmed after

each code + off sequence.

Check that entry/exit delay zones provide the

assigned delay times.

9-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Step

Action

Check the keypad-initiated alarms, if

programmed, by pressing the panic key pairs

(✳ and #, 1 and ✳, and/or 3 and #).

The word ALARM and a descriptor “99” are

displayed for ✳ and #. If [1] and [✳] are

pressed, “95” is displayed; if [3] and [#] are

pressed, “96” is displayed.

If the system has been programmed for

audible emergency, the keypad emits a loud,

steady alarm sound. Silence the alarm by

entering the security code and pressing OFF.

If the system has been programmed for silent

panic, there are no audible alarms or

displays. A report is sent to the central

station, however.

Notify the central station that all tests are

finished, and verify results with them.

Testing Wireless Transmitters

Transmitter ID Sniffer Mode

Go/No Go Test Mode

Use the Transmitter Sniffer Mode to test that

transmitters have all been properly programmed.

Checking the transmitters in this mode assists in

determining good mounting locations, and verifies that

the RF transmission has sufficient signal amplitude

margin for the installed system.

If a transmitter does not have its serial number

“enrolled,” it will not turn off its zone number.

•

All partitions containing wireless

transmitters must be placed in the test

mode for sensitivity reduction of the RF

receiver (50% sensitivity). Otherwise, the

RF receiver remains at full strength.

To enter the Transmitter ID Sniffer Mode, proceed as

follows:

•

Make sure that all partitions are disarmed

when performing this test, as the wireless

receiver gain is reduced in half.

Step

Action

Enter Installer Code + [#] + [3]. The

keypad displays all zone numbers of wireless

units programmed into the system.

To enter the Go/No Go Test Mode, proceed as follows:

Step

Action

Fault each wireless zone, causing each device

to transmit.

Enter Installer Code + [5].

Fault each wireless transmitter, causing each

device to transmit.

As the system receives a signal from each of

the transmitters, the zone number of that

transmitter disappears from the display.

NOTE: If a single receiver is used, the

keypad beeps three times to indicate signal

reception. If two receivers are used, the

keypad beeps once if the first receiver

received the signal, twice if the second

receiver received the signal, and three times

if both receivers heard the signal.

Enter Installer Code + OFF to exit the

Sniffer Mode.

If the keypad does not beep, reorient or move

the transmitter to another location. Usually

a few inches in either direction is all that is

required.

Enter Installer Code + OFF to exit the

Go/No Go Test Mode.

9-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 10 – Testing The System

Trouble Conditions

Check or Trouble Messages

Power Failure

Display Description

Display

CHECK

Description

This indicates that a problem exists on

the zone number displayed. Zone trouble

may be caused by one of the following

conditions:

AC LOSS

This indicates that the system is

operating on battery power only. Check

to see that the circuit breaker for the

branch circuit that your system’s

transformer is wired to has not been

accidentally turned off. Instruct the

user to call a service representative

immediately if AC power cannot be

restored.

POWER

LED is off

•

A hardwired fire zone is open

(broken wire).

A Day/Night zone (zone type 5) is

faulted.

A polling loop zone is not seen by

the control panel.

A polling loop zone has been

tampered (cover removed on a

4190).

Other System Messages

Display

Description

COMM

FAILURE

This indicates that a failure occurred in

the telephone communication portion of

your system.

•

A wireless zone has not checked in

during the time programmed in field

1✳31.

LO BAT

This indicates that a low-battery

condition exists in the wireless

transmitter displayed. Pressing any key

silences the audible warning sound.

•

A 5800 Series transmitter has been

tampered (cover removed).

A system trouble exists (RF

receiver, bell output, etc.).

SYSTEM LO This indicates that a low-battery

BAT

condition exists with the system’s backup

battery.

If the problem has been corrected, enter an

OFF sequence (Security Code + OFF) twice

to clear the display.

RCVR

SETUP

ERROR

This indicates that the system has more

wireless zones programmed than the

wireless receiver can support. If this is

not corrected, none of the zones in the

system will be protected. If additional

wireless zones are desired, use an

appropriate receiver.

MODEM

COMM

This indicates that the control is on-line

with a remote computer.

To the Installer

Regular maintenance and inspection (at least annually)

by the installer and frequent testing by the user are

vital to continuous satisfactory operation of any alarm

system.

Turning the System over to the User

Fully explain the operation of the system to the user by

going over each of its functions, as well as the User’s

Manual supplied.

The installer should assume the responsibility of

developing and offering a regular maintenance program

to the user as well as acquainting the user with the

proper operation and limitations of the alarm system

and its component parts. Recommendations must be

included for a specific program of frequent testing (at

least weekly) to ensure the system’s proper operation at

all times.

In particular, explain the operation of each zone

(entry/exit, perimeter, interior, fire, etc.). Be sure the

user understands how to operate any emergency

feature(s) programmed into the system.

9-3

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Having this information handy will make it easier for

us to serve you quickly and effectively.

Contacting Technical Support

PLEASE, before you call Technical Support, be sure

you:

You may contact Technical Support via Toll-Free Fax.

Please include your return fax number. You will receive

a reply within 24 hours.

•

READ THE INSTRUCTIONS!

Check all wiring connections.

Determine that the power supply and/or backup

battery are supplying proper voltages.

•

Verify your programming information where

applicable.

Verify that all keypads and devices are addressed

properly.

Note the proper model number of this product, and

the version level (if known) along with any

documentation that came with the product.

•

Note your customer number and/or company name.

Technical Support:.................................................... 1-800-645-7492 (8 a.m.-8 p.m. EST)

ATLIS-FAX FAXBACK Automated Fax Retrieval System:.................... 1-800-573-0153 or

.................................................................................................1-516-921-6704 / ext. 1667

World Wide Web Address: .......................................... http://www.honeywell.com/security

9-4

Download from Www.Somanuals.com. All Manuals Search And Download.

A P P E N D I X

Regulatory Agency Statements

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

UL Installation Requirements

The following requirements apply to both UL Residential and UL Commercial Burglary installations:

•

All partitions must be owned and managed by the same person(s).

All partitions must be part of one building at one street address.

The audible alarm device(s) must be placed where it/they can be heard by all partitions.

The control cabinet must be protected from unauthorized access. This can be done by installing a tamper switch on

the cabinet door (not supplied with VISTA-40) or by installing a UL Listed passive infrared detector positioned to

detect cabinet access. Wire the selected device to any EOLR-supervised zone (Zone 1-8). Program this zone for day

trouble/night alarm (type 05) or 24-hour audible alarm (type 07) response. The 24-hour alarm response must be used

for multiple-partitioned systems.

•

Remote downloading and auto-disarming are not UL Listed features.

NOTE: UL Commercial Burglary installations require the attack resistant cabinet. The cabinet is included in the

VISTA-ULKT kit.

UL609 Grade A Local Mercantile Premises/Local Mercantile Safe & Vault

Use the following guidelines for a Grade A Local Mercantile Premises/Local Mercantile Safe & Vault installation:

•

All zones must be configured for EOLR supervision (✳41=0). Wireless sensors may not be used. If 4190WH RPMs

are used, set field ✳24 to “0” to enable tamper detection.

Attach a door tamper switch (supplied) to the VISTA-40 cabinet backbox. For safe and vault installations, a shock

sensor (not supplied) must also be attached to the backbox. (Also see SECTION 3: Installing the Control)

Wire an AB12 Grade A Bell/Box to the bell output. Bell wires must be run in conduit. Program the bell output for a

timeout of 16 minutes or longer timeout and for confirmation of arming ding. (Also see SECTION 3: Installing the

Control.)

•

Wire the VISTA-40 tamper switch and AB12 Bell/Box tamper switches to any EOLR-supervised zone (zones 1-8).

Program this zone for day trouble/night alarm (type 05) or 24-hour audible alarm (type 07) response. The 24-hour

alarm response must be used for multiple-partitioned systems.

Entry delays must not exceed 45 seconds, and exit delays must not exceed 60 seconds.

UL365 Police Station Connected Burglar Alarm

Follow the instructions for UL609 local installations given above.

For Grade A Service:

•

You may use the VISTA-40 dialer alone, or the 7720 Long Range Radio alone.

When using the dialer, program it to send Burglary Alarm, Low Battery, and Communicator Test reports. Field ✳27

must be set to “024” (or less).

•

If you are using the 7720, connect it to the VISTA-40 burglary/audible panic alarm trigger.

For Grade AA Service:

•

You must use a 7920SE Long Range Radio.

Connect the 7920SE to the VISTA-40 burglary/audible panic alarm trigger.

A-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

UL611/UL1610 Central Station Burglary Alarm

Follow the instructions for UL609 Local installations given above.

For Grade A Service:

•

You must use the VISTA-40 dialer with a 7720 Long Range Radio.

Connect the control’s burglary/audible panic alarm trigger (on J7 header) and the 659EN’s phone line monitor

output to the 7720. The 7720 will send a report to the central station when a telephone line fault condition is

detected.

•

Also connect the 7720’s radio fault output to one of the VISTA-40 EOLR-supervised zones (i.e., 1-8). Program this

zone for a trouble by day/alarm by night (type 05) or a 24-hour alarm (type 07, 08) response to radio faults.

Program the control’s dialer to send Burglary Alarm, Trouble, Opening/Closing, and Low Battery reports.

For Grade AA Service:

Follow the instructions for Grade A service, except use the 7920SE in place of the 7720.

California State Fire Marshal (CSFM) and UL Residential Fire Battery Backup

Requirements

The California State Fire Marshal and UL have regulations that require all residential fire alarm control panels to have

backup battery with sufficient capacity to operate the panel and its attached peripheral devices for 24 hours in the

intended standby condition, followed by at least 4 minutes in the intended fire alarm signaling condition.

The VISTA-40 can meet this requirement without using a supplemental power supply, provided that the panel’s outputs

(including the current drawn from the auxiliary power output terminals) are limited as shown below:

•

Output current is limited to 750mA maximum total auxiliary power, polling loop, and bell output current.

Maximum auxiliary current is 300mA (including polling loop current).

A 14AH battery is used. (Yuasa model NP7-12 recommended; use two connected in parallel.) A dual-battery harness

is provided with the 4100EOLR Resistor Kit (kit also contains EOL resistors having spade lug/heat shrink tubing

construction approved by UL and CSFM for fire zone usage). Both batteries fit inside the panel’s cabinet.

A-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix A – Regulatory Agency Statements

FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15 STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS

In the event of telephone operational problems, disconnect the control panel by removing the plug from the

RJ31X (CA38A in Canada) wall jack. We recommend that you demonstrate disconnecting the phones on

installation of the system. Do not disconnect the phone connection inside the control panel. Doing so will

result in the loss of your phone lines. If the regular phone works correctly after the control panel has been

disconnected from the phone lines, the control panel has a problem and should be returned for repair. If

upon disconnection of the control panel, there is still a problem on the line, notify the telephone company that

it has a problem and request prompt repair service. The user may not under any circumstances (in or out of

warranty) attempt any service or repairs to the system. It must be returned to the factory or an authorized

service agency for all repairs.

FCC PART 68 NOTICE

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that

contains, among other information, the FCC registration number and ringer equivalence number (REN) for

this equipment. If requested, this information must be provided to the telephone company.

This equipment uses the following jacks:

An RJ31X is used to connect this equipment to the telephone network.

The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive

RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most,

but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices

that may be connected to the line, as determined by the total RENs, contact the telephone company to

determine the maximum REN for the calling area.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance

that temporary discontinuance of service may be required. If advance notice is not practical, the telephone

company will notify the customer as soon as possible. Also, you will be advised of your right to file a

complaint with the FCC if you believe necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could

affect the operation of the equipment. If this happens, the telephone company will provide advance notice in

order for you to make the necessary modifications in order to maintain uninterrupted service.

If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty

information. If the trouble is causing harm to the telephone network, the telephone company may request

that you remove the equipment from the network until the problem is resolved.

There are no user serviceable components in this product, and all necessary repairs must be made by the

manufacturer. Other repair methods may invalidate the FCC registration on this product.

This equipment cannot be used on telephone company-provided coin service. Connection to Party Line

Service is subject to state tariffs.

This equipment is hearing-aid compatible.

When programming or making test calls to an emergency number, briefly explain to the dispatcher the

reason for the call. Perform such activities in the off-peak hours, such as early morning or late evening.

A-3

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

CANADIAN EMISSIONS STATEMENTS

This Class B digital apparatus complies with Canadian ICES-003

NOTICE

AVIS

L’étiquette d’Industrie Canada identifie le

matériel homologué. Cette étiquette certifie que le

matériel est conforme aux normes de protection,

d’exploitation et de sécurité des réseaux de

télécommunications, comme le prescrivent les

documents concernant les exigences techniques

relatives au matériel terminal. Le Ministère

n’assure toutefois pas que le matériel fonctionnera

à la satisfaction de l’utilisateur. Avant d’installer

ce matériel, l’utilisateur doit s’assurer qu’il est

permis de le raccorder aux installations de

l’enterprise locale de télécommunication. Le

matériel doit également être installé en suivant

une méthode acceptée da raccordement. L’abonné

ne doit pas oublier qu’il est possible que la

conformité aux conditions énoncées ci-dessus

n’empêche pas la dégradation du service dans

certaines situations.

The Industry Canada Label identifies certified

equipment. This certification means that the

equipment meets telecommunications network

protective, operational and safety requirements as

prescribed in the appropriate Terminal Equipment

Technical

Requirements

document(s).

The

Department does not guarantee the equipment

will operate to the user’s satisfaction.

Before installing this equipment, users should

ensure that it is permissible to be connected to the

facilities of the local telecommunications company.

The equipment must also be installed using an

acceptable method of connection. The customer

should be aware that compliance with the above

conditions may not prevent degradation of service

in some situations.

Repairs to certified equipment should be

coordinated by a representative designated by the

supplier. Any repairs or alterations made by the

Les réparations de matériel nomologué doivent

être coordonnées par un représentant désigné par

le fournisseur. L’entreprise de télécommunications

peut demander à l’utilisateur da débrancher un

user

this

equipment,

equipment

malfunctions, may cause the telecommunications

company to request the user to disconnect the

equipment.

appareil

la suite de réparations ou de

modifications effectuées par l’utilisateur ou à

Users should ensure for their own protection that

the electrical ground connections of the power

utility, telephone lines, and internal metallic

water pipe system, if present, are connected

together. This precaution may be particularly

important in rural areas.

cause de mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit

s’assurer que tous les fils de mise à la terre de la

source

téléphoniques

d’energie

électrique,

des canalisations

lignes

d’eau

métalliques, s’il y en a, sont raccordés ensemble.

Cette précaution est particulièrement importante

dans les régions rurales.

Caution: Users should not attempt to make such

connections themselves, but should contact an

appropriate electric inspection authority, or

electrician, as appropriate.

Avertissement : L’utilisateur ne doit pas tenter

de faire ces raccordements lui-même; il doit avoir

racours à un service d’inspection des installations

électriques, ou à un électricien, selon le cas.

NOTICE: The Ringer Equivalence Number

(REN) assigned to each terminal device provides

an indication of the maximum number of

terminals allowed to be connected to a telephone

interface. The termination on an interface may

consist of any combination of devices subject only

to the requirement that the sum of the Ringer

Equivalence Numbers of all the devices does not

exceed 5.

AVIS : L’indice d’équivalence de la sonnerie

(IES) assigné à chaque dispositif terminal indique

le nombre maximal de terminaux qui peuvent être

raccordés à une interface. La terminaison d’une

interface téléphonique peut consister en une

combinaison de quelques dispositifs, à la seule

condition que la somme d’indices d’équivalence de

la sonnerie de tous les dispositifs n’excède pas 5.

A-4

Download from Www.Somanuals.com. All Manuals Search And Download.

A P P E N D I X

Summary of System Commands

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

User Code

Commands

Add A User Code = User Code + 8 + New User Number + New User’s Code

Change a Code = User Code + 8 + User Number + New User’s Code

Delete a User’s Code = Your User Code + 8 + User Number to Be Deleted + Your Code

Again

View User Capability = User’s Code + [✳] + [✳]

Set Real-Time Clock (Installer, Master Only) = Code + [#] + 63

Programming

Commands

Site Initiated Download = User Code + [#] + 1.

Direct-Wire Download Enable = User Code + [#] + 5.

Enter Program Mode = Installer Code + 800.

Enter Interactive Program Mode = Installer Code + 800 + [#] + 93

Exit Program Mode = ✳99 or ✳98.

Event Logging

Commands

Event Log Display = Code + [#] + 60 (Installer or Master Only)

Event Log Print = Code + [#] + 61 (Installer or Master Only)

Clear Event Log = Code + [#] + 62 (Installer or Master Only)

Wireless System

Commands

House ID Sniffer Mode = Code + [#] + 2 (Installer Only)

Transmitter ID Test = Code + [#] + 3 (Installer Only)

Go/No Go Test = Code + 5 (Test Key)

Additional

Commands

Partition GOTO

GOTO Home Partition

Panics

User Code + [✳] + Partition Number 0-2.

User Code + [✳] + 0.

[✳] + 1 or A Key (Zone 95).

[✳] + [#] or B Key (Zone 99).

[#] + 3 or C Key (Zone 96).

Press 0 for 5 Seconds.

View Downloaded Messages

Display All Zone Descriptors

Display User Self Help

Press [✳] for 5 Seconds.

Hold Any Key for 5 Seconds.

Relay Device

Control Commands

Activate Relay Device as Programmed = User Code + [#] + 71.

Activate Relay Device as Programmed = User Code + [#] + 72.

Activate Relay Device Manually = User Code + [#] + 70.

Activate Access Relay for Current Partition = User Code + 0.

Access Control

Commands

B-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

B-2

Download from Www.Somanuals.com. All Manuals Search And Download.

A P P E N D I X

Specifications

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

VISTA-40 CONTROL

Physical:

Standard Cabinet (included) 12 1/2" W x 14 1/2" H x 3" D

UL Cabinet (optional)

Electrical:

14 1/2" W x 18" H x 4.3" D (Included in the VISTA-ULKT kit)

Voltage Input:

From the 1361 Plug-In Transformer (use 1361CN in Canada) or 1361X10 transformer

(for X-10 installations) rated 16.5VAC, 40 VA.

Alarm Sounder Output:

Auxiliary Power Output:

Backup Battery:

10VDC-13.8VDC, 1.7 amps max. (UL1023, UL609 installations); 750mA less aux.

current draw (UL985 installations).

9.6VDC-13.8VDC, 750mA max. For UL installations, the accessories connected to the

output must be UL Listed, and rated to operate in the above voltage range.

12VDC, 4AH or 7AH gel cell. YUASA NP4-12 (12V, 4AH) or NP7-12 (12V, 7AH)

recommended.

Standby Time:

4 hours min. with 750mA aux. load using 7 AH battery.

Circuit Protectors:

PTC circuit breakers are used on battery input to protect against reverse battery

connections and on alarm sounder output to protect against wiring faults (shorts).

A solid-state circuit breaker is used on auxiliary power output to protect against wiring

faults (shorts).

Digital Communicator

Formats Supported:

ADEMCO High Speed, ADEMCO 4 + 2 Express, ADEMCO Low Speed, ADEMCO

Contact ID, Sescoa and Radionics Low Speed

Line Seize:

Double Pole

0.7B

Ringer Equivalence:

FCC Registration No.:

AC398U-68192-AL-E

Remote Keypads

6139

6160

Physical:

Width:

Height:

6.25 inches

Width:

Height:

7.437 inches

5.25 inches

1.312 inches

4.75 inches

1.25 inches

Depth:

Electrical:

Voltage Input:

12VDC

100mA

Voltage Input:

12VDC

150mA

Current Drain:

Interface Wiring:

RED:

Current Drain:

Interface Wiring:

RED:

12VDC input (+) auxiliary

power

12VDC input (+) auxiliary

power

BLUE:

Not Used

BLUE:

Not Used

GREEN:

YELLOW:

BLACK:

Data to control panel

Data from control panel

GREEN:

YELLOW:

BLACK:

Data to control panel

Data from control panel

Ground and (-) connection from

supplemental power supply

Ground and (-) connection from

supplemental power supply

C-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

C-2

Download from Www.Somanuals.com. All Manuals Search And Download.

A P P E N D I X

Contact ID Event Codes

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

TABLE OF CONTACT ID EVENT CODES

Code

110

121

122

123

131

132

134

135

150

301

302

305

306

309

321

332

333

344

373

380

Definition

Code

381

382

383

384

401

403

406

407

408

409

411

441

570

602

606

607

621

625

626

Definition

Fire Alarm

Loss of Supervision (RF)

Loss of RPM Supervision

RPM Sensor Tamper

RF Transmitter Low Battery

O/C by User

Duress

Silent Panic

Audible Panic

Perimeter Burglary

Interior Burglary

Entry/Exit Burglary

Day/Night Burglary

24-Hour Auxiliary

AC Loss

Power-Up Armed/Auto-Arm

Cancel by User

Remote Arm/Disarm (Download)

Quick Arm

Keyswitch O/C

Low System Battery

System Reset

Callback Requested

Armed STAY

Program Tamper

Battery Test Fail

Bell 1 Trouble

Bypass

Communicator Test

Listen-In to Follow

Burglary Walk-Test

Event Log Reset

Poll Loop Short-Trouble

Expansion Module Failure

RF Jam

Time/Date Reset

Fire Loop Trouble

Trouble (global)

Time/Date Inaccurate

D-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

D-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

#93 Menu Mode Programming.................................... 4-2

#93 Menu Mode Programming Commands................. 4-3

12/24 Hour Type Stamp Format................................ 5-11

1361 ...................................................................3-24, C-1

1361X10 Transformer ...................................... 3-17, 3-24

24-hour Audible Alarm Type 07................................... 4-6

24-hour Auxiliary Alarm Type 08 ................................. 4-6

24-hour Silent Alarm Type 06...................................... 4-6

2-Wire Latching Glassbreak Detectors...................... 3-10

2-Wire Smoke Detectors ............................................. 3-7

333 PRM ..................................................................... 3-8

4100SM.............................................................. 3-19, 4-7

4100SM Serial Module................................................ 6-3

4146 .......................................................................... 3-18

4197 Polling Loop Extender ...................................... 3-12

4204 and 4204CF Relay Modules............................. 3-16

4208 Module Zone Assignment................................... 5-8

4285/4286 VIP Module.............................................. 3-20

4297 Polling Loop Extender ...................................... 3-12

4-Wire Smoke Detectors ............................................. 3-7

5800 Series Transmitters .......................................... 3-15

5800TM Module ........................................................ 3-15

5869 .......................................................................... 3-13

5881 RF Receivers.................................................... 3-13

5881ENHC ................................................................ 3-13

6139 ............................................................................C-1

6160 ............................................................................C-1

675 Ground Start Module.......................................... 3-17

685 Receiver ............................................................. 3-22

719 .............................................................................. 3-4

747 .............................................................................. 3-4

7720 .......................................................................... 3-19

7720ULF.................................................................... 3-19

7920SE...................................................................... 3-19

Alarm Code for Zones 25–32 .......................................5-6

Alarm Code for Zones 33–40 .......................................5-6

Alarm Code for Zones 41–48 .......................................5-6

Alarm Code for Zones 49–56 .......................................5-7

Alarm Code for Zones 57–64 .......................................5-7

Alarm Code for Zones 65–72 .......................................5-9

Alarm Code for Zones 73–80 .....................................5-10

Alarm Code for Zones 87–88 .......................................5-7

Alarm Code for Zones 89–99 .......................................5-7

Alarm Output Current Load ........................................3-26

Alarm Output Supervision ............................................3-4

Alarm Sounder Duration...............................................5-2

ALPHA PROG..............................................................4-3

Arm Stay and Time Set Report Codes (First Digit).....5-10

Arm Stay and Time Set Report Codes (Second Digit)5-10

Arm-Away Type 21.......................................................4-6

Arm-STAY Type 20 ......................................................4-6

Audio Alarm Verification Module ................................3-22

AUXILIARY OUTPUT ENABLE........................ 3-17, 3-19

Auxiliary Output Mode................................................5-10

Auxiliary Power Current Load.....................................3-26

BACK-UP BATTERY...................................................C-1

Battery Capacity Worksheet.......................................3-27

Battery Selection Table..............................................3-27

Battery Test..................................................................9-1

Burglary Alarm Communicator Delay...........................5-8

Burglary Trigger for Response Type 8 .........................5-3

Burglary Walk Test.......................................................9-1

Button RF (BR) Type 05..................................... 3-15, 4-6

Cabinet Lock ................................................................3-1

California State Fire Marshal (CSFM) ......................... A-2

Callback .......................................................................6-2

Callback Requested .....................................................6-1

CANADIAN EMISSIONS STATEMENTS.................... A-4

Changing a User Code.................................................8-4

Check Messages..........................................................9-3

Checksum Verification..................................................5-5

Chime on External Siren ............................................5-10

CIRCUIT PROTECTORS............................................C-1

Code + TEST [5] ..........................................................9-1

Cold Water Pipe.........................................................3-25

COMM FAILURE..........................................................9-3

Communication Defaults ..............................................4-4

Communicator Split Reporting Selection......................5-9

Compass Downloading Software ......................... 6-1, 6-3

Compatible 2-Wire Smoke Detectors...........................3-7

Compatible 4-Wire Smoke Detectors...........................3-7

Compatible 5800 Series Transmitters........................3-16

Compatible Alarm Indicating Devices...........................3-4

Compatible Glass Break Detectors ............................3-10

AAV ........................................................................... 3-22

AB12............................................................................ 3-1

ABB1031 ..................................................................... 3-4

AC Loss Keypad Sounding.......................................... 5-2

AC Outlet Ground...................................................... 3-25

Access Control ............................................................ 4-7

Access Control Commands......................................... B-1

Access Relay Number............................................... 5-11

Adding a User Code.................................................... 8-3

Adding an RF Key to a User Code .............................. 8-4

Addressing the Keypads.............................................. 3-3

ADEMCO 4+2 EXPRESS.....................................3-5, C-1

ADEMCO CONTACT ID..............................................C-1

ADEMCO HIGH SPEED..............................................C-1

ADEMCO LOW SPEED .......................................3-5, C-1

Agency Statements ..................................................... A-1

Alarm Code for Zones 01–08 ...................................... 5-6

Alarm Code for Zones 09–16 ...................................... 5-6

Alarm Code for Zones 17–24 ...................................... 5-6

In d ex-1

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

Compatible Polling Loop Devices.............................. 3-11

Confirmation of Arming Ding ....................................... 5-2

CONTACT ID EVENT CODES....................................D-1

Contacting Technical Support ..................................... 9-4

Control Unit Power Supply Load ............................... 3-26

Conventions Used in This Manual.................................. vi

CUSTOM INDEX......................................................... 4-3

EXPERT MODE ...........................................................4-3

External Sounders........................................................3-4

FCC Part 15 STATEMENT.......................................... A-3

FCC PART 68 NOTICE............................................... A-3

FCC REGISTRATION NO...........................................C-1

First Communication ....................................................6-2

First Test Report Time..................................................5-8

Data Encryption........................................................... 6-1

Data Field Descriptions ............................................... 5-1

Data Field Programming Mode.................................... 4-1

Daylight Saving Time Start/End Month...................... 5-11

Daylight Saving Time Start/End Weekend ................ 5-12

Deleting a User Code.................................................. 8-4

DEVICE PROG............................................................ 4-3

Dial Tone Detection..................................................... 5-5

Dial Tone Pause.......................................................... 5-4

Dialer Test................................................................... 9-1

DIGITAL COMMUNICATOR........................................C-1

DIP Switch Loop (DP) Type 07.................................... 4-6

Dip Switch Polling Loop Right Loop (PS) Type 08 ...... 4-6

Direct-Wire Downloading............................................. 6-3

Disable Download Callback....................................... 5-11

Disarm Type 22........................................................... 4-6

Download Command Enables..................................... 5-4

Download ID Number.................................................. 5-4

Download Phone Number ........................................... 5-4

Downloading................................................................ 6-1

Downloading Access Security ..................................... 6-1

Downloading Requirements ........................................ 6-1

Dual Reporting ............................................................ 5-5

Duress Codes Level 6 ................................................. 8-2

Duress Reporting ........................................................ 8-2

General Description......................................................1-1

Getting On-Line with a Control Panel...........................6-2

Global Arm ? ................................................................8-3

Go/No Go Test Mode ...................................................9-2

Grade A Mercantile Premises Listing...........................3-1

Grade A Mercantile Safe and Vault Listing ..................3-2

Grade A Service...................................................A-1, A-2

Grade AA Service.................................................A-1, A-2

Ground Start Module..................................................3-17

Hardwire and Optional Expansion Zones.....................1-1

Hardwired (HW) Type 01..............................................4-6

House ID Sniffer Mode...............................................3-15

ID Digit for Zones 01–08 ..............................................5-6

ID Digit for Zones 09–16 ..............................................5-6

ID Digit for Zones 17–24 ..............................................5-6

ID Digit for Zones 25–32 ..............................................5-6

ID Digit for Zones 33–40 ..............................................5-6

ID Digit for Zones 41–48 ..............................................5-6

ID Digit for Zones 49–56 ..............................................5-7

ID Digit for Zones 57–64 ..............................................5-7

ID Digit for Zones 65–72 ..............................................5-9

ID Digit for Zones 73–80 ............................................5-10

ID Digit for Zones 87–88 ..............................................5-7

ID Digit for Zones 89–99 ..............................................5-7

Ignore Expansion Zone Tamper...................................5-3

Installer (User 1) Code Level 0.....................................8-1

Installer Code...............................................................5-1

Installing RPM Devices ..............................................3-10

Installing The Control ...................................................3-1

Installing the Control's Circuit Board ............................3-2

Intelligent Test Report..................................................5-3

Interior w/Delay Type 10 ..............................................4-6

Interior, Follower Type 04 ............................................4-5

Earth Ground............................................................. 3-25

Enable 5800 RF Button Force Arm ........................... 5-11

Enable 5800 RF Button Global Arm.......................... 5-11

Enable Dialer Reports for Panics & Duress................. 5-8

Enable GOTO for this Partition.................................. 5-12

Enable J7 Triggers for Partition................................. 5-12

Enable Open/Close Report for Installer Code ............. 5-4

Enable Open/Close report for Keyswitch..................... 5-4

Entering Programming Mode....................................... 4-1

Entry Delay #1............................................................. 5-1

Entry Delay #2............................................................. 5-1

Entry Warning.............................................................. 5-8

Entry/Exit #1 Type 01.................................................. 4-5

Entry/Exit #2 Type 02.................................................. 4-5

Event Log .................................................................. 3-19

Event Log .................................................................... 1-2

Event Log Types ....................................................... 5-11

Event Logging Commands.......................................... B-1

Exit Delay #1 ............................................................... 5-1

Exit Delay #2 ............................................................... 5-2

Exit Delay Sounding.................................................. 5-10

Exiting the User Edit Mode.......................................... 8-4

Keypad Panic Enables.................................................5-2

Keypads .......................................................................2-1

Keyswitch ...................................................................3-18

Keyswitch Assignment .................................................5-2

In d ex-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

Keyswitch Tamper..................................................... 3-18

Prevent Zone XX Bypass .............................................5-4

Primary Format.............................................................5-5

Primary Phone Number................................................5-4

Primary Subscriber’s Account Number.........................5-3

Printer Configurations ................................................3-19

Program Modes............................................................4-1

Programming................................................................4-1

Programming Commands ........................................... B-1

PROGRAMMING COMMANDS ...................................4-1

Programming Entry Errors............................................4-2

Programming Partition-Specific Data Fields.................4-2

Programming System-Wide Data Fields ......................4-2

LINE SEIZE.................................................................C-1

List of Figures..................................................................v

LO BAT........................................................................ 9-3

Long Range Radio to J7 Triggers ............................. 3-19

Low Speed Format (Primary) ...................................... 5-5

Low Speed Format (Secondary).................................. 5-5

Manager Codes Level 2 .............................................. 8-1

Master Codes Level 1.................................................. 8-1

MODEM COMM ................................................... 6-1, 9-3

modems....................................................................... 6-1

Mounting The Control Cabinet .................................... 3-1

Multi-Access ? ............................................................. 8-3

Multiple Alarms............................................................ 5-2

Multiple Partition Access ............................................. 8-2

Quick Arm............................................................. 5-3, 8-1

RADIONICS LOW SPEED ..........................................C-1

Randomize AC Loss Report.........................................5-2

RCVR SETUP ERROR ................................................9-3

Real-Time Clock...........................................................7-1

Regulatory Agency Statements................................... A-1

RELAY PGM ................................................................4-3

Relay Timeout XXX Minutes ......................................5-11

Relay Timeout YYY Seconds.....................................5-11

Remote Keypad Sounder...........................................3-19

Reporting Formats........................................................3-5

Response Types for Zones 01–08 ...............................5-1

Response Types for Zones 09–16 ...............................5-1

Response Types for Zones 17–24 ...............................5-1

Response Types for Zones 25–27, 97, 95, 96,

No Alarm Response Type 23 ...................................... 4-6

Non-Alarm Report Codes (First Digit........................... 5-7

Non-Alarm Report Codes (Second Digit...................... 5-8

Non-UL Installations.................................................... 3-4

Normally Closed or EOLR (Zones 2-8)........................ 5-4

Number of Codes per Partition.................................. 5-12

Number of Partitions.................................................. 5-11

and 99 ......................................................................5-1

Response Types for Zones 28–32 ...............................5-9

Response Types for Zones 33–40 ...............................5-9

Response Types for Zones 41–48 ...............................5-9

Response Types for Zones 49–56 ...............................5-9

Response Types for Zones 57–64 ...............................5-9

Response Types for Zones 87–91 ...............................5-9

Restore Report Timing .................................................5-8

RF Receiver Supervision Check-in Interval..................5-9

RF System Installation Advisories..............................3-13

RF System Operation and Supervision......................3-13

RF Transmitter Check-in Interval .................................5-9

RF Transmitter Low Battery Reporting.........................5-9

RF Transmitter Low Battery Sound..............................5-9

Ring Count ...................................................................6-2

Ring Detection Count...................................................5-5

RINGER EQUIVALENCE............................................C-1

RJ31X ..........................................................................3-5

RJ31X jack.................................................................3-21

RLY VOICE DESCR.....................................................4-3

OC or OPEN CIRCUIT ................................................ 3-3

On-Line Control Functions .......................................... 6-2

Open/Close Reporting................................................. 8-2

Operator Access Levels .............................................. 6-1

Operator Codes Levels 3-5 ......................................... 8-1

Output Device Control Commands.............................. B-1

Output Devices.......................................................... 3-16

Overvoltage Protection................................................ 3-5

PA400.......................................................................... 3-4

PABX Access Code..................................................... 5-3

Partitioned System ...................................................... 2-1

Partitioning ........................................................... 1-1, 2-1

Perimeter Type 03....................................................... 4-5

Peripherals Devices..................................................... 1-1

Permanent Keypad Display Backlighting................... 5-10

Phone Module Access Code ....................................... 5-2

Polling Loop............................................................... 3-10

Polling Loop Current Draw ........................................ 3-26

Polling Loop Supervision........................................... 3-12

Power Failure .............................................................. 9-3

Power-Up in Previous State ........................................ 5-3

Prevent Fire Timeout................................................... 5-2

Secondary Format........................................................5-5

Secondary Phone Number...........................................5-4

Secondary Subscriber Account Number ......................5-8

Send Cancel If Alarm + Off ........................................5-11

In d ex-3

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-40 Installation and Setup Guide

serial number devices................................................ 3-11

Serial Number Polling Loop (SL) Type 06................... 4-6

Serial Printer.............................................................. 3-20

SESCOA .....................................................................C-1

Sescoa/Radionics........................................................ 3-5

Sescoa/Radionics Select............................................. 5-5

Siren Driver ................................................................. 3-5

Smoke Power Reversal Module .................................. 3-8

Specifications ..............................................................C-1

Standard/Expanded Reporting Primary....................... 5-6

Standard/Expanded Reporting Secondary.................. 5-6

Standby Battery Size................................................. 3-27

Supervised Fire (Without Verification) Type 09........... 4-6

Supervised RF........................................................... 3-15

Supervised RF (RF) Type 03....................................... 4-6

Supervision Pulses for LRR....................................... 5-12

Supervisory and Restore Codes for Zones 01–16 ...... 5-6

Supervisory and Restore Codes for Zones 17–32 ...... 5-6

Supervisory and Restore Codes for Zones 33–48 ...... 5-7

Supervisory and Restore Codes for Zones 49–64 ...... 5-7

Supervisory and Restore Codes for Zones 65–80 .... 5-10

Supervisory and Restore Codes for Zones 87–99 ...... 5-7

Supplementary Power Supply..................................... 3-3

Suppress Transmitter Supervision Sound................. 5-10

Swinger Suppression .................................................. 5-8

System Commands ..................................................... B-1

System Communication............................................... 1-1

SYSTEM LO BAT........................................................ 9-3

System LoBat”............................................................. 9-1

System Messages ....................................................... 9-3

System Sensor A77-716B EOL Relay Module ............ 3-7

System Sensor MA 12/24D ......................................... 3-4

System Sensor P12575............................................... 3-4

UL609 Grade A Local Mercantile Premises/Local

Mercantile Safe & Vault........................................... A-1

UL611/UL1610 Central Station Burglary Alarm........... A-2

UL985 Household Fire or Household Fire/Burglary

Installations ..............................................................3-4

Unsupervised RF........................................................3-15

Unsupervised RF (UR) Type 04...................................4-6

Use Partition Descriptor .............................................5-12

User Access Codes......................................................8-1

User Code Authority Levels..........................................8-1

User Code Commands................................................ B-1

User Code Rules..........................................................8-2

Users............................................................................2-1

View Capabilities..........................................................8-1

VIP Module.................................................................3-20

VIP Module Phone Code..............................................5-2

VISTA-40 Current Load..............................................3-26

Wheelock AS-121575W ..............................................3-4

Wire Run Length/Gauge ..............................................3-3

Wireless Keypad Assignment.....................................5-10

Wireless Keypad Tamper Detect................................5-10

Wireless System Commands ...................................... B-1

Wireless Zone Expansion...........................................3-13

Wiring Devices to Zones 1-9 ........................................3-6

Wiring the Alarm Output...............................................3-4

Wiring the Keypads......................................................3-3

Worksheets to calculate the total current ...................3-26

World Wide Web Address............................................9-4

Telco Handoff.............................................................. 6-3

Telephone Line Connections....................................... 3-5

TELEPHONE OPERATIONAL PROBLEMS................ A-3

Test Report Interval..................................................... 5-3

Testing The System..................................................... 9-1

TouchTone or Rotary Dial ........................................... 5-3

TouchTone with Rotary Backup .................................. 5-9

Transformer Connections.......................................... 3-24

Transmitter Battery Life............................................. 3-16

Transmitter ID Sniffer Mode ........................................ 9-2

Transmitter Input Types............................................. 3-15

Transmitter Supervision............................................. 3-15

Trouble by Day/Alarm by Night Type 05...................... 4-5

Trouble Conditions ...................................................... 9-3

Trouble Messages....................................................... 9-3

Turning the System Over to the User.......................... 9-3

X-10............................................................................3-17

Yuasa.........................................................................3-27

Zone 5 Audio Alarm Verification.................................5-11

Zone 804....................................................................3-20

Zone 9 Fast/Slow Response ........................................5-2

Zone Defaults...............................................................4-4

Zone Index ...................................................................4-4

Zone Input Type Definitions .........................................4-6

Zone Number Designations..........................................4-4

ZONE PROG...........................................................vi, 4-3

Zone Response Type Definitions .................................4-5

Zone Type Restores for Zone Types 1-8 .....................5-7

Zone Type Restores for Zone Types 9, and 10............5-7

Zones ...........................................................................2-1

UL Installation Requirements ...................................... A-1

UL1023 Household Burglary Installations ................... 3-4

UL365 Police Station Connected Burglar Alarm.......... A-1

In d ex-4

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING!

THE LIMITATIONS OF THIS ALARM SYSTEM

While this System is an advanced wireless security system, it does not offer guaranteed protection against burglary, fire or

other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a vari-

ety of reasons. For example:

•

Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or

disconnect an alarm warning device.

•

Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work with-

out power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in

properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.

•

Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the

signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.

•

A user may not be able to reach a panic or emergency button quickly enough.

While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not acti-

vate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the

Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may

not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not

sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side

of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor de-

tector, for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No

smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by

carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable

materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire

and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to

allow all occupants to escape in time to prevent injury or death.

•

Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their

installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams

of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion

or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.

Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical

system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the

ambient temperature of the protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection

performance can decrease.

Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the

other side of closed or partly open doors. If warning devices are located on a different level of the residence from the bed-

rooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear

the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic.

Finally, alarm warning devices, however loud, may not warn hearing-impaired people.

•

Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or

temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect them-

selves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately.

This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to

last as long as 20 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This

alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad

(and remote keypad) should be tested as well.

Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions.

Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device

being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all

reduce the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation,

thus allowing time to arrange a change of battery to maintain protection for that given point within the system.

Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute

for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and

continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm

systems owe it to themselves and their loved ones to learn about these developments.

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

Honeywell International Inc., 165 Eileen Way, Syosset, New York 11791, warrants its product(s) to be in

conformance with its own plans and specifications and to be free from defects in materials and workmanship

under normal use and service for 24 months from the date stamp control on the product(s) or, for product(s)

not having a date stamp, for 12 months from date of original purchase unless the installation instructions or

catalog sets forth a shorter period, in which case the shorter period shall apply. Seller’s obligation shall be

limited to repairing or replacing, at its option, free of charge for materials or labor, any product(s) which is

proved not in compliance with Seller’s specifications or proves defective in materials or workmanship under

normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the

product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. For

warranty service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way,

Syosset, New York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A

PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE

FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL

OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR

IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR

DAMAGE IS CAUSED BY THE SELLER’S OWN NEGLIGENCE OR FAULT.

Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the

product(s) will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that

the product(s) will in all cases provide adequate warning or protection. Customer understands that a

properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or

other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not

occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER

SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS

BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS

HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING

UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN,

SELLER’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF

THE PRODUCT(S), WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST

SELLER.

This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s).

No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

165 Eileen Way, Syosset, New York 11791

www.honeywell.com/security

¬1ꢀꢁꢁꢂ9ꢃ+lꢄ

N7001V5 5/04 Rev A

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Inc Paint Sprayer 234180 User Manual
Graco Music Mixer 24C728 B User Manual
Greenheck Fan Ventilation Hood SE1 User Manual
HANNspree Flat Panel Television K226 10A1 User Manual
Harbor Freight Tools Fan 66950 User Manual
Hoshizaki Kitchen Entertainment Center CF3B FS User Manual
HP Hewlett Packard Server PC2 6400 User Manual
HP Hewlett Packard Switch 4 32B SAN User Manual
IBM CRT Television LC UXT3 User Manual
Ikelite Digital Camera A710IS User Manual