16” OSCILLATING STAND
FAN
66950
SeT up AND OperATING INSTruCTIONS
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
read this material before using this product.
Failure to do so can result in serious injury.
reAD AND SAVe THeSe INSTruCTIONS.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAuTION, without
the safety alert
SpeCIFICATIONS
symbol, is used to address
practices not related to
personal injury.
Electrical Requirements 120 V~ / 60 Hz / .37 A
Low: 1120 RPM
Speeds (approximately) Medium: 1280 RPM
High: 1420 RPM
Additional Safety Instructions
HOuSeHOLD uSe ONLY
1. Maintain labels and nameplates on
the tool. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
e197533
uNpACkING
2. Do not run Power Cord (36) under
carpeting. Do not cover Cord with
throw rugs, runners or similar cover-
ings. Arrange cord away from traffic
area and where it will not be tripped
over.
When unpacking, make sure item is
intact and undamaged. If parts are miss-
ing or broken, call Harbor Freight Tools at
1-800-444-3353 as soon as possible.
Save This Manual
3. Use only in dry environments. Do not
use in bathrooms, laundry area, near
sinks or other sources of water.
Keep this manual for safety warnings
and precautions, assembly, operating, in-
spection, maintenance and cleaning pro-
cedures. Write product’s serial number in
back of manual near assembly diagram (or
month and year of purchase if product has
no number). Keep this manual and receipt
in a safe place for future reference.
4. Do not run Fan without Front and
Rear Grills (2, 6) in place.
5. This product is not a toy. Keep it out
of reach of children.
6. WARNING: Handling Cord on this
product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
7. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all conditions
and situations that may occur. It must
be understood by operator that com-
mon sense and caution are factors
which cannot be built into this prod-
uct, but must be supplied by operator.
SKU 66950
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Extend Upper Column (42) from
Lower Shaft and thread Height Ad-
justment Knob back onto Lower
Column until its threaded back into
place. WArNING! This must be done
before top half of Fan is assembled
onto Upper Column.
ASSeMBLY
read the eNTIre ruLeS FOr
SAFe OperATION section at
the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
4. Unthread Spinner (3) from Spindle
(7) by turning it clockwise. Remove
Plastic Nut (5) from Motor Housing,
by turning it counterclockwise. See
Figure B, below.
TO preVeNT
SerIOuS INjurY
FrOM ACCIDeNTAL
OperATION Or eLeCTrIC
SHOCk: Before assembly,
cleaning or adjustment, make
sure OFF key is pressed and
the cord is unplugged.
3
5
23, 25
Note: For additional information regarding
parts listed, refer to Assembly Dia-
gram at back of manual.
24
42
6
4
7
28
41
2
41
30
Figure B
29
5. Slide Rear Grill (6) over retainer on
face of Motor Housing, aligning loca-
tor pin on Housing with pin hole for
Rear Grill. In this mode, the catch
on edge of Rear Grill will be at low-
est position. Thread on Plastic Nut
(5) clockwise, but do not overtighten.
See Figure B.
33
34
Figure A
1. Using Screws (30) and Washers (31,
32), attach Lower Shaft (41) to Upper
Cross Stand (33) and Lower Cross
Stand (34). See Figure A, above.
6. Insert Propeller over Spindle. Align
cross-pin of Spindle with recess in
the inner face of Propeller. Attach
Spinner (3), turning it counterclock-
wise to tighten. See Figure B.
2. Unthread and remove Height Adjust-
ment Knob (28) from Lower Shaft.
Slide Base Cover (29) down Shaft
until it covers intersection of Upper
and Lower Cross Stands.
7. Fasten Front Grill (2) onto Rear Grill
(6) using latches along edges of both
Grills and the locking screw on the
SKU 66950
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Grill. WArNING! Do not acti-
vate Fan until properly latched.
INSpeCTION AND MAINTeNANCe
TO preVeNT
SerIOuS INjurY
FrOM ACCIDeNTAL
OperATION Or eLeCTrIC
SHOCk: Before appliance
inspection or maintenance,
make sure Off key is pressed
and power Cord is unplugged.
8. Use Screws (24) to fasten Front and
Rear Shaft Housing (23, 25) to Upper
Shaft. See Figure B.
OperATION
read eNTIre ruLeS FOr
SAFe OperATION section at
beginning of manual including
all text under subheadings
therein before set up or use.
TO preVeNT SerIOuS
INjurY FrOM AppLIANCe
FAILure: Do not use
damaged appliances. If
abnormal noise or vibration
occurs, have the problem
corrected before further use.
1. To make the fan oscillate, push the
Knob (11) down. To make the fan
stop oscillating, pull the Knob up.
2. To adjust the angle of air flow, tilt the
Housing (12) and move to desired
angle.
1. BeFOre eACH uSe, inspect con-
dition of the Fan. Check for loose
screws, misalignment or binding of
moving parts, cracked or broken
parts, and any other condition that
may affect its safe operation.
3. To adjust height of fan, loosen the
Height Adjustment Knob (28) and
raise or lower fan. Retighten Knob
once desired height is reached.
2. Clean regularly to prevent dust from
accumulating on Propeller (4). Un-
fasten latches along Front and Rear
Grills, remove Front Gill, and use
damp cloth to wipe Blade. Dry and
replace Front Grill before use.
4. To activate, plug the Power Cord (36)
into the nearest wall outlet.
5. To adjust the speed, push one of the
desired Switches (21). The available
speeds are Low, Medium and High.
To turn off fan, press the Off Switch.
3. To maximize air circulation, dismantle
Grills and Propeller and wash and dry
each part when dirty.
4. WArNING! Do not allow any water to
get into the Motor (8).
pLeASe reAD THe FOLLOWING CAreFuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy
REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER ASSUMES ALL
RISK AND LIABILITy ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 66950
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
pArTS LIST AND ASSeMBLY DIAGrAM
part
1
2
3
4
5
6
7
8
Description
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
4
1
1
1
1
1
4
4
4
1
1
4
1
1
1
1
1
1
1
Center Piece
Front Grill
Spinner
Propeller
Plastic Nut
Rear Grill
Spindle
Motor
42
9
Connector
Oscillating Lever
Knob
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Housing
Screw
Screw
Insulator
Screw
Neck
41
Positioning Board
Spring
Screw
Speed Switches
Clip
Front Shaft Housing
Screws
Rear Shaft Housing
Nut
Screws
Height Adjustment Knob
Base Cover
Screw
record product’s Serial Number Here:
Washer
Washer
Note: If product has no serial number,
record month and year of purchase
instead.
Upper Cross Stand
Lower Cross Stand
Leg Cap
Power Cord
Cord Clamp
Spring
Note: Some parts are listed and shown
for illustration purposes only, and
are not available individually as re-
placement parts.
Ball
Screws
Lower Column
Upper Column
SKU 66950
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|