ELECTRIC KEY BOX
95041
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvement, actual product may differ slightly from the product described herein.
Note: Harbor Freight Tools is not responsible for the loss of any property stored within this
safe due to theft, fire, or any other circumstance.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
N0TE:
Harbor Freight Tools is not responsible for the loss of any property stored
within this safe due to theft, fire, or any other circumstance.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your Key Box, check to make sure that all parts listed in the parts list on page 5 are
included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353. It is important that you read the entire manual to become familiar with the product
BEFORE you operate and use the Key Box.
Operation
Your Key Box comes completely assembled. It is important that you read the entire manual to
become familiar with the product BEFORE you set up and use the Key Box.
1.
Opening the Key Box for the first time: On the Keypad (7) enter the factory preset
Personal Identification Number (PIN) which is 159B. When the Green LED light goes on,
turn the Knob (4) clockwise and the Key Box will open-see Assembly Diagram.
2.
To program your own PIN: On the Keypad (7) enter the factory preset PIN which is 159B.
When the Green LED Light goes on, turn the Knob (4) clockwise and the Key Box will open-
see Assembly Diagram. Press the Red Button (11) on the inside of the door near the hinges.
Select a new PIN, with 3 to 8 numbers, and press the “B” key.
The green light will go on to indicate that the PIN has been successfully programmed. Make
a note of the new PIN and store it in a safe place away from the Key Box.
Test your new PIN before closing the door. Make certain you have a Manual Override Key(8)
available when setting a new PIN or changing batteries in case the door doesn’t open.
Note: The Knob (4) on the Door must be turned within 5 seconds of the green light coming on, or
else the PIN must be re-entered.
Note: If you or an intruder incorrectly enter the PIN, the yellow light will go on. Entering an incorrect
PIN three times will freeze the system for 20 seconds.
3.
4.
Using the Manual Override Key (8) : The Manual Override Keys can be used if you
forget your PIN, if the batteries are not installed in the Key Box, or if the batteries are dead.
NEVER lock your Manual Override Keys (8) into the Key Box, store them seperately
in a safe place.
At the center of the Key Box door (see Assembly diagram) is the Key Cover (5). Remove the
Cover (5) and pull the panel outward to expose the key hole. Insert the Manual Override
Key (8) and turn counterclockwise. Turn the Knob and pull the door open.
SKU 95041
For technical questions please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
6.
To close and lock the Key Box: Close the door and turn the Knob in the opposite direction
used to open the Key Box. Pull the door gently to make certain it is properly locked.
Installing batteries: The red LED light on the Keypad (7) will light up when the batteries
need replacing. When this light appears, IMMEDIATELY replace the batteries.
Open the Safe door. Unsnap the Battery Cover (10) from the Door. Remove the old
batteries and install four new “AA” batteries in their place in the battery compartment. Make
certain to align the polarity of the batteries as indicated in the battery compartment. Snap in
the Battery Cover (10).
7.
8.
After replacing the batteries, the PIN may need to be reset. To reset PIN, follow instructions
in Step 2 on page 3.
Mounting the Key Box: To mount the Key Box to a wall or surface, use a drill to set the path
for each Bolt (9). Make certain that the drilling path is clear and free of obstacles
such as wires, cables and electrical lines. Use wall anchors (not included) as
necessary. Insert the Bolts (9) (included) through each drilled hole and into a stud to
secure the Key Box to the desired surface.
9.
The Key Box comes with four Steel Hook Hanger Brackets (13). These come in four colors
to match the Plastic Key Hanger Rings which also come in (4) colors.
10.
Install the Steel Hook Hanger Brackets (13) either onto the slots on the inside of the Key Box,
the Door or both. The four Steel Hook Hanger Brackets are numbered 1 through 20. Once
the Steel Hook Brackets are installed, the Plastic Key Rings (12) can be hung on them. The
Plastic Key Rings can be set to correspond to either the number or color of the Steel Hook
Hanger Brackets (13).
Maintenance
1.
Protect the Key Box from moist or wet conditions. Moisture may cause electronic damage in
the keypad or corrosion of the steel.
2.
3.
Occasionally wipe the Key Box and keypad clean with a soft dry cloth or brush.
Occasionally apply a small amount of light oil or lock lubricant to the mechanical lock
mechanism. Be careful not to get any oil or other liquids on or near the electronic
mechanism.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 95041
For technical questions please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Part Description
Quantity
1
2
3
4
5
6
Body
Door
Front Cover
Knob
Key Cover
LED Light
1
1
1
1
1
3
(Green, Yellow, Red)
Keypad
7
1
8
Manual Override Key 2
9
Bolt
2
10
11
12
13
Battery Cover
Red Button
Plastic Key Ring
Steel Hook Hanger
Brackets
1
1
20
4
2
14
Steel Wall Anchors
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Parts/Assembly Diagram
13
14
12
14 Not shown
SKU 95041
For technical questions please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
|