15" PLANER
MODEL G1021Z
INSTRUCTION MANUAL
COPYRIGHT ©2000 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
JANUARY, 2000 PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Of Contents
PAGE
6.
OPERATIONS
OVERVIEW..............................................................................................................29
TABLE LOCKS ........................................................................................................29
POWER FEED ........................................................................................................30
HANDWHEEL ..........................................................................................................30
DEPTH LIMITER ....................................................................................................30
TEST RUN ..............................................................................................................31
WOOD SPECIES ....................................................................................................31
WOOD CHARACTERISTICS ..................................................................................32
MAINTENANCE
GENERAL................................................................................................................33
TABLE......................................................................................................................33
KNIVES....................................................................................................................33
LUBRICATION....................................................................................................34-35
CLOSURE ....................................................................................................................36
7.
8.
TROUBLESHOOTING..............................................................................................................37
ADJUSTMENT BLOCK PATTERN..........................................................................................38
G1021Z 15" Planer
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous conditions.This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages.The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for prop-
er accident prevention measures.
Indicates an imminently hazardous situation which, if not
avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoid-
ed, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoid-
ed, MAY result in minor or moderate injury. It may also be
used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
5. KEEP CHILDREN AND VISITORS AWAY.
All children and visitors should be kept a
safe distance from work area.
1. KEEP GUARDS IN PLACE and in working
order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning on.
6. MAKE WORK SHOP CHILD PROOF with
padlocks, master switches, or by removing
starter keys.
7. DON’T FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRON-
MENT. Don’t use power tools in damp or
wet locations, or where any flammable or
noxious fumes may exist. Keep work area
well lighted.
8. USE RIGHT TOOL. Don’t force tool or
attachment to do a job for which it was not
designed.
-4-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD. Make
sure your extension cord is in good condi-
tion. Conductor size should be in accor-
dance with the chart below. The amperage
rating should be listed on the motor or tool
nameplate. An undersized cord will cause a
drop in line voltage resulting in loss of
power and overheating.Your extension cord
must also contain a ground wire and plug
pin. Always repair or replace extension
cords if they become damaged.
13. DON’T OVERREACH. Keep proper footing
and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubri-
cating and changing accessories.
15. DISCONNECT TOOLS before servicing
and changing accessories, such as blades,
bits, cutters, and the like.
Minimum Gauge for Extension Cords
16. REDUCE THE RISK OF UNINTENTION-
AL STARTING. Make sure switch is in off
position before plugging in.
LENGTH
AMP RATING
0-6
7-10
11-12
13-16
25ft 50ft 100ft
18
18
16
14
12
10
16
16
16
12
12
10
16
14
14
12
10
No
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury.
17-20
21-30
18. CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part
that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, bind-
ing of moving parts, breakage of parts,
mounting, and any other conditions that
may affect its operation. A guard or other
part that is damaged should be properly
repaired or replaced.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear
is recommended. Wear protective hair cov-
ering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT safe-
ty glasses.
19. NEVER LEAVE TOOL RUNNING UNAT-
TENDED.TURN POWER OFF. Don’t leave
tool until it comes to a complete stop.
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than
using your hand and frees both hands to
operate tool.
G1021Z 15" Planer
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions For Planers
1. Ensure that the machine sits firmly on the
floor before use. Any “wobbles” must be
corrected by shimming or blocking before
operation.
7. Do not remove excessive amounts of
wood in a single pass.
8. Inspect your stock before planing. Reject
stock with defects and foreign material.
2. This machine is not designed to process
any other material except wood.
9. Do not attempt to remove jams until power
is disconnected and all moving parts have
come to a complete stop.
3. Never position fingers or thumbs near the
infeed roller.
10. Provide adequate infeed and outfeed
4. Long stock should always be fully support-
space for operating the planer.
ed by some type of support fixture.
11. Do not plane wood less than 12" long and
1
5. Do not operate planer with dull or damaged
⁄4" thick.
knives.
12. Do not plane lumber with loose knots or
knots that may become loose during
planing.
6. Ensure that the planer is properly adjusted
before using.
Like all power tools, there is danger associ-
ated with the Model G1021Z 15" Planer. Use
the tool with respect and caution to lessen
the possibility of mechanical damage or
operator injury. If normal safety precau-
tions are overlooked or ignored. Serious
personal injury may occur.
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies to
your individual working conditions. Use
this and other machinery with caution and
respect. Failure to do so could result in seri-
ous personal injury, damage to equipment
or poor work results.
Operation of this equipment has the poten-
tial to propel debris into the air which can
cause eye injury. Always wear safety glass-
es or goggles when operating equipment.
Everyday glasses or reading glasses only
have impact resistant lenses, they are not
safety glasses. Be certain the safety glass-
es you wear meet the appropriate stan-
dards of the American National Standards
Institute (ANSI).
-6-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: CIRCUIT REQUIREMENTS
Grounding
220V Operation
The G1021Z Planer motor is wired to operate at
220V only. A cordset without a 220V plug is
included with the Model G1021Z. Plugs and
receptacles can be purchased at your local hard-
ware store or home center. Contact your local
electrical contractor if uncertain about connecting
to a 220V circuit.
In the event of an electrical short, grounding
reduces the risk of electric shock by providing a
path of least resistance to disperse electric cur-
rent. This tool is equipped with a power cord hav-
ing an equipment-grounding conductor. The out-
let must be properly installed and grounded in
accordance with all local codes and ordinances.
When operating at 220V, we recommend using a
NEMA-style 6-15 plug and outlet as depicted in
Figure 1. You may also “hard-wire” the planer
directly to your panel, provided you place a dis-
connect switch near the machine. Check the elec-
trical codes in your area for specifics on wiring
requirements.
This equipment must be grounded. Please
ensure that this machine is continuously
grounded from the motor to the machine frame
and then to a known ground. Verify that any
existing electrical outlet and circuit you intend
to plug into is actually grounded. If it is not, it
will be necessary to run a separate 12 A.W.G.
copper grounding wire from the outlet to a
known ground. Under no circumstances should
the grounding pin from any three-pronged plug
be removed. Serious personal injury may
occur.
220V/240V
15A
NEMA L6-15
Extension Cords
Figure 1. NEMA 6-15 220V/15A connector.
We do not recommend the use of extension cords
on 220V equipment. It is much better to arrange
the placement of your equipment and the
installed wiring to eliminate the need for exten-
sion cords. Should it be necessary to use an
extension make sure the cord is rated Hard
Service (grade S) or better. Refer to the chart in
Section 1: Safety Instructions to determine the
minimum gauge for the extension cord. The
extension cord must also contain a ground wire
and plug pin. Always repair or replace extension
cords when they become worn or damaged.
Fusing
Under normal load, the Model G1021Z draws
about 12 amps. We recommend a 15-amp circuit
or a 20-amp slow-blow fuse. A circuit rated any
higher will not adequately protect the motor.
Equipment returned to us for service that shows
evidence of being over-fused will be repaired or
replaced totally at the customer’s expense,
regardless of the present warranty status.
G1021Z 15" Planer
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: GENERAL INFORMATION
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 326-3806
Commentary
Fax: (800) 438-5901
E-Mail: [email protected]
We are proud to offer the Grizzly Model G1021Z
15" Planer. The Model G1021Z is part of a grow-
ing Grizzly family of fine woodworking machinery.
When used according to the guidelines set forth
in this manual, you can expect years of trouble-
free, enjoyable operation and proof of Grizzly’s
commitment to customer satisfaction.
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G1021Z as supplied when the manual was pre-
pared. However, owing to Grizzly’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
Whenever possible, though, we send manual
updates to all owners of a particular tool or
machine. Should you receive one, we urge you to
insert the new information with the old and keep
it for reference.
The Model G1021Z is intended for home and pro-
fessional use. The G1021Z features a 3 HP, 220V
single-phase motor with an easy Off magnetic
power switch, jack screw and/or spring loaded
knife setting, triple belt drive, large side-mounted
handwheel and a solid one-piece cabinet stand.
A number of optional accessories for the Model
G1021Z are available through the Grizzly catalog.
They include a heavy-duty mobile base, roller
stands, replacement knives and Planer Pal® plan-
er jigs, which are invaluable when setting up or
adjusting your planer’s cutting knives.
To operate this, or any power tool, safely and
efficiently, it is essential to become as familiar
with its characteristics as possible. The time
you invest before you begin to use your Model
G1021Z will be time well spent. DO NOT oper-
ate this machine until you are completely famil-
iar with the contents of this manual. Make sure
you read and understand all of the safety pro-
cedures. If you do not understand something,
DO NOT operate the machine.
We are also pleased to provide this manual with
the Model G1021Z. It was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It repre-
sents our effort to produce the best documenta-
tion possible. If you have any comments regard-
ing this manual, please write to us at the address
below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/
O
Bellingham, WA 98227-2069
Most importantly, we stand behind our machines.
If you have any service questions or parts
requests, please call or write us at the location
listed below.
-8-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Parts Inventory
After all the parts have been removed from the
container, you should have:
The planer is shipped from the factory in a care-
fully packed crate. If you find the machine to be
damaged after you’ve signed for delivery and the
truck and driver are already gone, you will need to
file a freight claim with the carrier. Save the con-
tainers and all packing materials for inspection by
the carrier or their agent. Without the packing
materials, filing a freight claim can be difficult. If
you need advice regarding this situation, please
call us immediately.
Planer Unit on Stand
Dust Port
Roller Extensions (2)
Dust Port Mounting Hardware
Cap Screw M6 - 1.0 x 12
Lock Washer M6
Hex Bolts M6 - 1.0 x 12
Hex Nuts M6 - 1.0
Washers M6
3
3
3
3
6
Roller Extension Mounting Hardware Bag
Hex Bolts M8 -1.25 x 20
Flat Washers 8mm
Setscrews M8 - 1.25 x 12
Depth Handwheel Hardware
Handle
6
6
6
The G1021Z is a heavy machine with a 540
lb. shipping weight. DO NOT over-exert
yourself while unpacking or moving your
machine – get assistance. In the event that
your planer must be moved up or down a
flight of stairs, be sure that the stairs are
capable of supporting the combined weight
of people and the machine. Failure to use
care while assembling or moving could
result in serious personal injury.
1
1
1
1
1
Hex Nut M10 - 1.25
Flat Washer 10mm
Scale (Hi - Lo)
Key
Knife Setting Jig
Knife Setting Jig Rod
Knife Setting Jig Brackets
E-clips
1
2
4
Tool Kit
Allen® Wrench 3mm
Allen® Wrench 4mm
Allen® Wrench 5mm
Allen® Wrench 6mm
Open End Wrench 8-10mm
Open End Wrench 12-14mm
1
1
1
1
1
1
In the event that any parts are missing, we will be
happy to replace them. Contact our Customer
Service number for assistance. If any non-propri-
etary parts such as nuts, bolts or washers are
missing, we will be happy to replace these too,
but for the sake of expediency, these items can
be obtained at your local hardware store.
NOTICE
A full parts list and breakdown can be
found toward the end of this manual. For
easier assembly, or to identify missing
parts, please refer to the detailed illustra-
tions at the end of the manual.
G1021Z 15" Planer
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean Up
Site Considerations
The unpainted surfaces are coated with a waxy
oil to protect them from corrosion during ship-
ment. Remove this protective coating with a sol-
vent cleaner or citrus-based degreaser. Avoid
chlorine-based solvents as they may damage
painted surfaces should they come in contact.
Always follow the usage instructions on the prod-
uct you choose for clean up.
FLOOR LOAD
Your G1021Z Planer represents a large weight
load in a small footprint. Most commercial floors
are suitable for the Model G1021Z. Some resi-
dential floors may require additional support to
accommodate both machine and operator.
WORKING CLEARANCES
Working clearances can be thought of as the dis-
tances between machines and obstacles that
allow safe operation of every machine without
limitation. Consider existing and anticipated
machine needs, size of material to be processed
through each machine, and space for auxiliary
stands and/or work tables. Also consider the rel-
ative position of each machine to one another for
efficient material handling. Be sure to allow your-
self sufficient room to safely run your machines in
any foreseeable operation.
Follow the safety rules listed below when
working with solvents.
1. Read and follow all directions and
warnings on the solvent label.
2. Work only in a well ventilated area.
3. Do not work near any type of open
flame (e.g., pilot lights, kerosene
heaters, and so on).
LIGHTING AND OUTLETS
4. DO NOT smoke while working with
flammable material.
Lighting should be bright enough to eliminate
shadow and prevent eye strain. Electrical circuits
should be dedicated or large enough to handle
combined motor amp loads. Outlets should be
located near each machine so power or exten-
sion cords are not obstructing high-traffic areas.
Be sure to observe local electrical codes for prop-
er installation of new lighting, outlets, or circuits.
5. Paper towels from the cleaning process
are extremely combustible. Dispose of
waste towels so they do not create a
fire hazard.
Many of the solvents commonly used to
clean machinery can be highly flammable,
and toxic when inhaled or ingested. Always
work in well-ventilated areas far from poten-
tial ignition sources when dealing with sol-
vents. Use care when disposing of waste
rags and towels to be sure they do not cre-
ate fire or environmental hazards. Keep
children and animals safely away when
cleaning and assembling this machine.
Make your shop “child safe”. Ensure that
your workplace is inaccessible to young-
sters by closing and locking all entrances
when you are away. Never allow visitors in
your shop when assembling, adjusting or
operating equipment.
-10-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: ASSEMBLY
Overview
Handwheel
The handwheel is used to raise and lower the
planer table.
The G1021Z Planer requires very little assembly
when you receive it. There a just a few easy
assembly steps to get the machine ready for your
shop. The machine should be properly adjusted
from the factory, however should you desire to
check the various settings, the following section
will detail the proper adjustment procedures.
TO MOUNT THE HANDWHEEL:
1. The handwheel shaft is at the front right
corner of the planer. Insert the key into the
keyway on the shaft, then line up the notch
on the handwheel bore with the key. Slide
the handwheel onto the shaft.
This planer unit is very heavy, approximately 480
lbs.There are lifting handles which slide out of the
base of the planer head (Figure 2) which can be
used to move the unit. These can be used as lift-
ing points using an overhead lift, block and tack-
le or a forklift, or if you have three other friends
who are each willing to grab a handle!
2. Slide the direction scale over the keyed
shaft so it sits on the center face of the
handwheel. See Figure 3.
3. Secure the handwheel with the 10mm -
1.25 hex nut and washer provided.
4. Attach the handle to the outer edge of the
handwheel. The handle threads into the
hole on the handwheel.
Lifting Handles
Figure 2. Location of lifting handles.
This planer is heavy and awkward to move.
We recommend that you use the proper
equipment to put the planer into position in
your shop or on a mobile base. Lifting with-
out proper equipment or ample assistance
could result in serious injury.
Figure 3. Handwheel attachment.
G1021Z 15" Planer
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Change Knob
Mounting Bolt
Thread the black plastic knob onto the speed
change shaft located on the right hand side of
the machine. See Figure 4. Note that speed
changes should only be done with the motor
running. See the Operations section.
Height Adjust
Setscrew
Figure 5. Extension roller attachment points.
4. Move the edge of the mounting bracket
which is closest to the table bed up or down
until the first roller is even with the straight-
edge. Tighten the mounting bolts just
enough to hold that position. Now adjust
the three setscrews until the roller which is
furthest out is even with the straightedge. It
may require various combinations of loos-
ening and/or tightening the setscrews and
bolts to level the extension rollers with the
table.
Figure 4. Installing speed change knob.
5. Repeat steps 3-4 for the other extension
roller assembly.
Extension Rollers
The infeed and outfeed extension rollers support
the work as it goes through the machine.
TO MOUNT THE EXTENSION ROLLERS:
1. Thread three (3) 8mm setscrews into the
mounting bracket of the extension rollers.
The setscrew holes are located just below
the mounting holes. Just start them into the
holes for now.
Figure 6. Checking extension roller height.
2. Use three (3) hex bolts and washers to
mount the extension rollers. See Figure 5.
Make sure the roller assembly is oriented
as shown in Figure 6.
3. Position a straightedge on the table bed, so
it lays on the table and suspends over the
extension rollers. See Figure 6.
-12-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Dust Port
Knife Setting Jig
The G1021Z Planer features a 4" dust port for
use with a dust collection system. If you will not
be using a dust collection system with this plan-
er, do not attach this dust port!
The knife setting jig has been provided to make
knife setting quick and easy. See Figure 8.
TO ASSEMBLE THE KNIFE SETTING JIG:
TO ATTACH THE DUST PORT:
1. Snap one of the E-clips over the notch on
one end of the knife setting rod.
1. Fit the dust port over the planer upper
cover. Line up the mounting holes. Three
holes go through the upper cover, and
three holes on the flange line up with three
threaded holes on the back of the planer
head.
2. Slide the cast aluminum knife setting jig
brackets onto the rod.
3. Snap the other E-clip onto the notch at the
other end of the knife setting jig rod.
2. Use three (3) M6 - 1.0 x 12mm hex bolts
and nuts and lock washers to secure the
dust port to the planer upper cover. See
Figure 7. It will be necessary to reach
inside the port opening with a wrench to
hold the nut to tighten the hex bolts.
3. Use three M6 - 1.0 x 12mm cap screws and
flat washers to secure the dust port to the
planer body.
Jig Rod
E-clip
Jig Bracket
Figure 8. Knife setting jig components.
Planer knives are dangerously sharp. Use
extreme caution when working near cutting
surfaces. Failure to exercise care while
working near knives could result in severe
personal injury.
Figure 7. Dust port assembly.
G1021Z 15" Planer
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ADJUSTMENTS
B. The handwheel raises and lowers the table
Overview
and controls the depth of cut. Turning the
handwheel clockwise raises the table and
counter-clockwise lowers the table.
Once assembly has been completed, your
C. The bed rollers ease stock movement
G1021Z 15" Planer requires just a few adjust-
through the planer and are adjustable.
ments to ready it for use in your shop.
D. The three position feed rate change knob
Many adjustments have already been made at
shifts planer feed speed from neutral to 16
and 20 feet per minute.
the factory, yet we recommend you familiarize
yourself with all of the following procedures to
gain a better understanding of the Planer’s con-
E. The table lock knob secures the table in a
struction and operation.
fixed position.
General control and adjustment locations are
shown in Figure 9:
F. Extra large ball bearing return rollers
G. Removable belt guard.
A. The switch is thermally protected and mag-
netically controlled and features push but-
tons to turn the planer on and off.
B
F
G
C
D
E
A
Figure 9. Overview of planer adjustment controls.
-14-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Gauge Block
Table Adjustment
Before attempting any table adjustments, you will
need to construct a gauge block. See Figure 10.
A larger gauge block diagram is also included at
the end of the manual for your convenience.
Precision adjustments later on require accuracy
when milling the gauge block. Do not use com-
mon 2x4 material. Use maple or similar type of
hardwood.
To plane stock perfectly square, it is important
that the table is parallel to the cutterhead.
TO CHECK TABLE PARALLELISM:
1. Place the gauge block on the table under
one end of the cutterhead.
2. Turn the handwheel to raise the table until
the block barely touches the cutterhead
body. The block should not be touching
the knives. See Figure 11.
Using a magnetic dial indicator is a good alterna-
tive to constructing a gauge block. Use the dial
indicator whenever the instructions call for use of
the gauge block and/or feeler gauge. Refer to the
current Grizzly catalog for dial indicators.
3. Slide the block toward the opposite side of
the cutterhead. Use a feeler gauge to mea-
sure the width of the gap, if any, between
the top of the block and the bottom of the
cutterhead. If there is a gap, make a note,
reading the distance from the feeler gauge.
4. If the block wedges tightly between the
table and cutterhead when shifting from
one side to the other, repeat steps 1
through 3 above, but start from the oppo-
site end of the cutterhead.
Figure 10. Guide block specifications.
DO NOT make adjustments while the planer
is running. Ensure that the switch is off,
power is disconnected and moving parts
have stopped before making adjustments.
Failure to comply could result in serious
injury or electrical shock hazard.
Figure 11. Guide block indicates parallelism.
If the gap difference from one side to the other is
equal to or less than 0.004", no further adjust-
ment is necessary.
G1021Z 15" Planer
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
If the gap difference from one side to the other is
greater than 0.004", but less than 0.016", go to
step 5.
Notes
If the gap difference from one side to the other is
greater than 0.016", the table raising chain under
the planer base will need to be adjusted. Please
call our Customer Service number for chain
adjustment instructions.
To adjust for gap differences of less than 0.016":
5. Determine which side of the table must be
raised to correct the gap.
6. Locate the two cap screws in the table cast-
ing for each of the columns. See Figure 12.
Loosen both sets of cap screws for each
column on the side you wish to adjust.
7. Push down or pull up the table in the
desired direction. Hold the table in position
and retighten the cap screws.
8. Recheck the table to cutterhead parallelism
again. Repeat steps 1 through 7 until the
deviation is less than 0.004".
Planer knives are dangerously sharp. Use
extreme caution when inspecting, removing,
sharpening, or replacing knives into the cut-
terhead. Substantial risk of injury!
Loosen these cap
screws to micro adjust
the table height
Lock Knob
Figure 12. Cap screws for column adjustment.
-16-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Knife Inspection
The knives are set at the factory using jack
screws before shipping. Springs are also included
with your machine, installed beneath the knives.
These may be used instead of the jack screws
depending on your preference. Refer to Figure
13 for placement of the jack screws or springs.
Figure 14. Placing springs into knife slots.
Jack Screw
Spring
The knives of your planer must be periodically
adjusted and will ultimately need to be removed
for sharpening. Adjustments should be as precise
as possible with tolerances within .002"-.003" to
prolong the sharpness of the knife edges.
Improperly adjusted knives can cause an imbal-
ance condition in the cutterhead and shorten
bearing life, as well as produce substandard
planing results.
Figure 13. Typical placement of jack screws or
TO INSPECT THE KNIVES:
1. UNPLUG THE PLANER!
springs.
If you decide you prefer to use the spring adjust-
ment method, you need to remove each knife,
remove the jack screws, leave the two springs
under each knife, and replace the knife.
2. Remove the dust port and upper cover and
cutterhead guard to expose the top of the
cutterhead. See Figure 15.
Loosen the gib bolts until the knife is loose in the
slot. The gib bolts turn clockwise to loosen and
counterclockwise to tighten (when facing the
head of the bolt). Carefully remove the knife. Back
the jack screws out completely from the threaded
hole and remove. If the springs have become dis-
lodged in the removal process, be sure to place 1
spring in each of the two holes in bottom of the
knife slot. The springs do not go into the threaded
hole where the jack screws were installed. See
Figure 14.
When using jack screws, it is not necessary to
install the springs. However it will not affect the
adjustment if both the springs and jack screws
are in place together.
Figure 15. Cover Removed, Jig on cutterhead
G1021Z 15" Planer
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the belt guard. Carefully turn the
cutterhead (using the pulley) until the first
knife is top dead center.
Knife Sharpening
4. Using the knife setting gauge, check the
knife height. The jig should sit solidly with
both feet on the cutterhead. See Figure 16.
If the knife is adjusted properly, the contact
point at the center of each adjuster should
just touch the tip of the knife. If the knife
does not make contact, or if the knife caus-
es the adjuster’s legs to not seat on the cut-
terhead, the knives need to be adjusted. It
may be helpful to mark the side of the knife
with an ink marker to indicate whether it is
high or low.This will make the actual adjust-
ment process easier.
Knife sharpness is one of the most important fac-
tors in getting good results with the planer. Knives
can be made to last a long time if care is taken in
checking the condition of the wood which is put
into the machine. The biggest problem will come
from wood with nails or other metal embedded.
This will nick or chip the knives and can require a
complete regrinding. Another wear factor is sand,
grit, or other dirt on the surface of the wood which
the knives have to cut through. At the speed the
cutterhead is rotating, these types of surface con-
tamination can have a very abrasive effect.
This planer has knives with a grind angle of 35˚
which is a configuration which should suit most
general planing needs. The optimal grind or bevel
angle is a compromise between effective cutting
(the smaller the angle the better the cutting
action) and edge life where the larger the angle
the more the edge is supported, thus the longer it
will last.
For the best results it is best to have planer knives
sharpened by a professional sharpening service
which has the grinding and measurement equip-
ment to assure that the knife cutting geometry is
maintained at optimum levels. It is a procedure
which requires some care and precision, other-
wise, a set of blades can be easily ruined. Knives
should always be ground as a set so they can be
properly matched. Unequal material removal can
result in an unbalanced cutterhead which can
affect not only planing surface quality but ulti-
mately the life of the cutterhead bearings.
Figure 16. Proper knife setting jig placement.
Once you have completed inspection on all three
knives, you will able to determine whether or not
there is a need to adjust the knives in the cutter-
head. Proceed to the appropriate section follow-
ing depending upon whether you are using the
jack screws or the springs.
Please refer to Section 6 Adjustments - Knife
Setting for complete detail on the removal and
reinstallation of planer knives.
-18-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Knife Setting
ADJUSTMENTS USING JACK
SCREWS
The knives are locked into the cutterhead with
wedge-type gibs and gib bolts. Jack screws under
the knives allow fine tuning to help in the setting
process.
To set the knives:
Figure 18. Tightening knives in cutterhead.
1. UNPLUG THE PLANER!
5. Adjust the screws below each end of the
knife until both feet of the gauge rest even-
ly on the cutterhead and the knife is just
touching the bottom of the middle foot of
the gauge. The gauge will set the knives at
a uniform protrusion of approximately .070"
above the cutterhead. The knife height
should vary no more than .002"-.003"
across the length of the cutterhead.
2. Remove the upper cover to expose the cut-
terhead.
3. Loosen the gib bolts until the knife is loose
in the slot. The gib bolts turn clockwise to
loosen and counterclockwise to tighten
(when facing the head of the bolt). See
Figure 17.
6. Maintain a constant pressure on the gauge
while re-tightening the gib bolts.
7. Repeat the same procedure on the remain-
ing knives. As mentioned before, the stan-
dard knife setting gauge is satisfactory for
reasonably accurate knife setting tasks.
When making adjustments, all three knives
must be adjusted the same. Do not adjust
one knife without adjusting the others as
well. Improper knife height adjustment can
result in damage to knives, poor planer per-
formance and possible operator injury.
Figure 17. Side view with jack screws.
4. Place the knife setting jig over the knife on
the cutterhead as shown in Figure 18. The
feet should be securely planted on the cut-
terhead. Make sure the gauge extension
rod is parallel to the cutterhead to maintain
accuracy.
Planer knives are dangerously sharp. Use
extreme caution when inspecting, remov-
ing, sharpening, or replacing knives into the
cutterhead. Substantial risk of injury!
G1021Z 15" Planer
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS USING SPRINGS
The knives are locked into the cutterhead with
wedge-type gibs and gib bolts. Jack screws under
the knives may be substituted with springs to help
in the setting process. It is advised that the jack
screws be removed when using the springs. To
set the knives:
1. UNPLUG THE PLANER!
2. Remove the upper cover to expose the cut-
terhead.
3. Loosen the gib bolts until the knife is loose
in the slot. The gib bolts turn clockwise to
loosen and counterclockwise to tighten
(when facing the head of the bolt). See
Figure 19.
Figure 20. Tightening knives in cutterhead.
6. Maintain a constant pressure on the gauge
while re-tightening the gib bolts. See Figure
20.
7. Repeat the same procedure on the remain-
ing knives. As mentioned before, the stan-
dard knife setting gauge is satisfactory for
reasonably accurate knife setting tasks.
When making adjustments, all three knives
must be adjusted the same. Do not adjust
one knife without adjusting the others as
well. Improper knife height adjustment can
result in damage to knives, poor planer per-
formance and possible operator injury.
Figure 19. Side view with springs.
4. Place the knife setting gauge on the cutter-
head as described previously, so the feet
are securely planted on the cutterhead.
Make sure the gauge extension rod is par-
allel to the cutterhead to maintain accuracy.
Planer knives are dangerously sharp. Use
extreme caution when inspecting, remov-
ing, sharpening, or replacing knives into the
cutterhead. Substantial risk of injury!
5. The downward pressure provided by the
gauge will set the knives at a uniform pro-
trusion of approximately .070" above the
cutter.The knife height should vary no more
than .002"-.003" across the length of the
cutterhead.
-20-
G1021Z 15"
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
Chip Breaker
Chipbreaker
Gauge Block
Infeed Roller
Cutterhead
The chip breaker is located on the top side of the
planer and extends down around the front of the
cutterhead. Its function is to prevent tear-out or
deep, unregulated gouging as the knives remove
material. The chip breaker works by breaking the
woodchips as they are being cut by the cutter-
head. The chip breaker also deflects and expels
the woodchips away from the surface of the
board and out of the planer.
TO ADJUST THE CHIPBREAKER:
Figure 21. Location of chip breaker assembly.
1. Disconnect the machine from the power
source, remove the dust hood and lower
the table.
6. If an adjustment is necessary, loosen the
locknuts and turn the setscrews. See
Figure 22. Stop turning when the bottom of
the chip breaker just touches the gauge
block.
2. Ensure that the knives are properly adjust-
ed.
7. Re-tighten both locknuts
8. Replace the exhaust hood.
3. Place the gauge block on the table directly
under the cutterhead. Using a one millime-
ter (0.040") feeler gauge between the
gauge block and the cutterhead, raise the
table until one of the knives just touches the
feeler gauge. Rotate the cutterhead manu-
ally to be sure the knife is at bottom dead
center.
4. Lock the table by tightening the table lock
knobs.
5. Remove the feeler gauge and slide the
gauge block under the chip breaker. See
Figure 21. The chip breaker should just
touch the top of the gauge block. Slide the
gauge block to the opposite end of the chip
breaker and check it in the same manner.
Figure 22. Chip breaker height adjustment.
DO NOT make adjustments while the planer
is running. Ensure that the switch is off,
power is disconnected and moving parts
have stopped before making adjustments.
Failure to ensure that power is disconnect-
ed could result in serious injury or electri-
cal shock hazard.
G1021Z 15" Planer
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Repeat steps 1-5 for the opposite side of
the roller. Repeat all steps for the outfeed
roller.
Feed Roller Height
Feeler gauge measurement should equal 0.040".
The infeed and outfeed rollers propel the lumber
through the planer.The rollers also press the lum-
ber flat against the planer table.
TO ADJUST ROLLER HEIGHT:
1. Remove the drive chain cover to access the
roller adjustments on the drive chain side of
the planer. A single socket head cap screw
holds the drive chain cover on. Belt side
adjustments are already accessible.
Set the infeed and outfeed rollers 0.040" below
the knife edge at bottom dead center.
TO CHECK ROLLER HEIGHT:
1. Disconnect the machine from the power
2. Loosen the roller adjustment check nuts
and turn the roller height setscrews to
change the height of the roller as needed.
See Figure 24.
source.
2. Lower the table so the gauge block will fit
under one side of the infeed roller.
3. Check roller height according to the above
instructions. Continue turning the setscrew
until the roller is properly adjusted.
3. Raise the table until the gauge block barely
touches the infeed roller. See Figure 23.
Do not change position of the table.
4. When the roller is set in the correct posi-
tion, re-tighten the check nuts you loosened
in Step 2 above.
4. Slide the gauge block over so it is under the
edge of one of the knives. Turn the cutter-
head until one of the knives is at bottom
dead center over the gauge block.
5. Check your settings one last time and
repeat steps 1-4 if necessary.
5. Measure the clearance between the top of
the gauge block and the edge of the knife
with a feeler gauge. Note the measurement
indicated on the feeler gauge.
Chipbreaker
Infeed Roller
Anti-Kickback
Fingers
Figure 24. Feed roller height adjustment.
Figure 23. Feed roller height inspection.
-22-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the springs that are in the holes
left by the setscrews. See Figure 26.
Feed Roller Pressure
5. Check for any dirt or grit. Clean the springs
and setscrews if dirty.
To be effective, the infeed and outfeed rollers
must put pressure on the workpiece as it feeds
through the planer. Too little pressure results in
slipping boards, too much pressure results in
jamming.
6. Screw
the
three
regular-pressure
setscrews back in until they are flush with
the top of the head casting.
7. Screw the light pressure setscrew until it is
Experiment with the best pressure settings for
your work situations. Some rough cut lumber will
feed through fine with relatively few problems,
while other lumber will have more difficulty.
1
approximately ⁄4" above the head casting.
The feed chain applies additional tension to
the right side of the outfeed roller, so the
pressure added by the setscrew need not
be as high.
Adjusting roller pressure does not affect height.
TO ADJUST ROLLER PRESSURE:
1. Disconnect the machine from the power
Pressure Setscrew
source.
2. Ensure that knives and feed rollers are set
Pressure Spring
Roller
correctly.
3. Unscrew the four large pressure setscrews
on top of the planer body. See Figure 25.
Height Setscrew
Check Nut
Light Pressure
Setscrew
Figure 26. Roller pressure assembly.
Regular
Pressure
Setscrews
Figure 25. Roller pressure adjustment.
G1021Z 15" Planer
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Loosen the setscrews on both sides of
each bed roller. See Figure 28.
Bed Rollers
The bed rollers ease stock movement through the
planer. The height of the bed rollers will vary
depending on the types of wood you will be plan-
ing. When planing rough stock, set the rollers
slightly high to keep the lumber from dragging
along the bed. However, snipe may be unavoid-
able. Smooth lumber should be planed with the
rollers set just above the plane of the table. This
will minimize snipe.
Setscrews
Setscrews
TO ADJUST THE BED ROLLERS:
1. Ensure that power is disconnected and lay
a high quality straightedge across both
table rollers. Use a try square to keep the
straightedge perpendicular to the table.
Figure 28. Adjusting bed roller height.
4. Use a wrench to turn the eccentric shafts
which adjust roller height. Stop turning
when the table rollers are at the proper
height.
2. Use a feeler gauge to measure the clear-
ance between the bottom of the straight
edge and the table. Ideal clearance is
between 0.002" and 0.005". Measure in
several places. This measurement must be
consistent across the entire table. See
Figure 27.
5. Once your roller heights are correct, re-
tighten all the setscrews.
6. Check the height of the table rollers. Repeat
steps 1-5 until the bed rollers are properly
set. Spin the bed rollers to ensure free
movement.
Figure 27. Inspecting bed roller height.
-24-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Move the deflector until its edge is approxi-
Chip Deflector
1
1
mately ⁄8" - ⁄4" from the tip of the cutting
knives. Push down on the deflector with a
wooden stick to check if it will touch the
knives. Cautiously rotate the cutterhead to
ensure clearance. Do Not touch the knives
- severe cuts may result.
The chip deflector keeps chips from falling onto
the outfeed roller. It is the orange plastic plate
located under the top cover.
4. Re-tighten the chip deflector mounting bolts
The beveled edge of the chip deflector should be
about 1⁄8" - 1⁄4" from the knife edge. Carefully rotate
the cutterhead to gauge the distance between the
chip deflector and the knives. Adjust if necessary.
However, if the chip deflector is set too close to
the knives, the rotating cutterhead may pull it in
and destroy it.
and re-mount the upper cover to the planer.
TO ADJUST THE CHIP DEFLECTOR:
Planer knives are dangerously sharp. Use
extreme caution when inspecting, remov-
ing, sharpening, or replacing knives into the
cutterhead. Substantial risk of injury!
1. Disconnect the machine from the power
source and remove the planer’s upper
cover.
2. Loosen the three deflector mounting bolts.
See Figure 29. Make sure the beveled
edge of the deflector faces the cutterhead.
Mounting Bolts
Cutterhead
Chip Deflector
Chipbreaker
Figure 29. Chip deflector access.
G1021Z 15" Planer
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Anti-Kickback
Belts
The Model G1021Z Planer provides an anti-kick-
back safety feature. The anti-kickback fingers
hang from a rod suspended across the front of
the cutterhead casting. The anti-kickback fingers
should be inspected regularly. Check the fingers
to ensure that they swing freely and easily. See
Figure 30.
The belt and pulley assembly are on the left side
of the planer. The belts transfer power from the
motor to the cutterhead and then through the
gearbox to the feed rollers. Remove the belt cover
by unscrewing the two lock knobs holding the
cover in place.
TO INSPECT/ADJUST THE PULLEYS:
Place a metal ruler or other straightedge across
the pulleys to check alignment. The pulleys are
aligned if the ruler crosses them evenly. See
Figure 31.
DO NOT apply oil or other lubricants to the
anti-kickback fingers. Oil or grease will
attract dust and restrict free movement of
the fingers, which could result in damage to
your workpiece, the planer, or possibly seri-
ous injury to the operator or others in the
workplace. Call our Customer Service num-
ber if the anti-kickback fingers do not move
freely when setting up your planer. DO NOT
attempt to use the planer if the anti-kick-
back fingers are not operating properly.
If the pulleys are out of alignment:
1. Loosen the bolts that hold the motor to the
motor mount bracket.
2. Adjust the position of the motor until the
pulleys are in line.
3. Re-tighten all bolts.
Figure 30. Anti-kickback assembly.
Figure 31. Checking pulley alignment.
-26-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CHECK BELT TENSION:
Gearbox
Squeeze the V-Belts at their midpoints with mod-
erate finger pressure. You should be able to
3
deflect each V-Belt about /4". Belts will rarely be
The gearbox is located just behind the handwheel
on the right side of the planer. The gearbox trans-
fers power from the belt-driven cutterhead to the
power feed rollers.The two-speed transmission is
controlled by a push/pull lever on the right side of
the planer. When engaged, the power feed rollers
will move lumber through the planer at either 16
or 20 feet-per-minute. The center lever position is
neutral.
too tight, but will sometimes be too loose.
To adjust belt tension:
1. Remove the belt guard using the two
threaded knobs. Remove the panel at the
back of the machine stand to gain access
to the motor assembly.
2. The motor pivots on a platform which is
suspended at one end by a threaded
adjustment bolt. Adjust the two locknuts up
or down the shaft until the desired belt
deflection is achieved. See Figure 32.
TO INSPECT THE GEARBOX:
1. Loosen the socket head cap screw on the
gearbox cover. Gently pull the cover off the
roll pins that hold it in place.
3. Tighten the bolts against the pivot plate to
2. Check the bolts holding the sprockets in
place. Inspect the drive chains to ensure
that the retaining clips are in place. Replace
the clips if necessary. See Figure 33.
lock the motor adjustment into place.
4. Check belt tension again. Repeat steps 2-3
as necessary.
Move these nuts to
adjust belt tension.
Figure 32. Adjusting belt tension.
Figure 33. Location of sprocket bolts.
DO NOT make adjustments while the planer
is running. Ensure that the switch is off,
power is disconnected and moving parts
have stopped before making adjustments.
Failure to comply could result in serious
injury.
G1021Z 15" Planer
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Re-measure the board and compare your
results with the scale. If there is a discrep-
ancy, loosen the scale adjustment screw
and correct the position. See Figure 34.
Thickness Scale
The thickness scale, located below the handwheel,
can be adjusted for accuracy. However, material
must be run through the machine to adjust the
thickness scale. Make certain you have followed the
directions in the Operations Section for Test
Running before attempting to make these adjust-
ments.
TO ADJUST THE SCALE:
1. Adjust the table height to the approximate
thickness of your test lumber. Measure the
lumber with calipers to determine its exact
thickness.
Adjustment
Screw
2. Move the table to 1/16" under the thickness of
your lumber and feed your test board through
the planer.
Figure 34. Thickness scale.
3. Turn the handwheel one half rotation and run
the board through once more. Turn the board
over and repeat.
NOTES
-28-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: Operations
planer on long stock, use the stock return
rollers on the top of the machine to move the
material back to the infeed side of the
machine.
The Model G1021Z 15" Planer is a powerful
woodworking machine, designed and con-
structed for professional-quality applica-
tions. Because of its powerful motor and
razor-sharp knives, the Model G1021Z is
inherently dangerous and should be oper-
ated with considerable caution and respect.
Failure to do so could result in damage to
the machine, or severe injury to the opera-
tor or others in the work area.
9. Avoid planing wood with a high water content.
Wood with more than 20% moisture content or
wood exposed to rain or snow, will plane poor-
ly and cause excessive wear to the knives and
motor. Excess moisture can also hasten rust
and corrosion.
10.Read as much as possible about planing pro-
cedures. Alternative publications present more
wood specific planing requirements. They will
often share tips on safety and more efficient
ways to operate your planer.
Overview
1. Inspect lumber for defects, warping, cupping,
twisting, and for foreign objects (nails, staples,
imbedded gravel, etc,). If you have any ques-
tion about the quality of your lumber, do not
use it. Remember, wood stacked on a con-
crete floor can have small pieces of stone or
concrete pressed into the wood.
Table Locks
Before attempting to adjust table height, loosen
the two black knobs on the left side of the table.
After table height is adjusted and the table height
is set, tighten the two black knobs back down
again. See Figure 35.
2. Use the full width of the planer. Alternate
between the left, the right and the middle
when feeding lumber into the planer. Your
knives will remain sharp much longer.
3. Scrape all glue off of joined boards before
planing.
4. Plane ONLY natural wood fiber. No wood com-
posites, laminates, particle board, plywoods or
plastics should be run through the planer.
5. Surface wood with the grain. NEVER feed
end-cut or end-grained lumber into your
planer.
6. Do not use boards with knots, splits, cross-
grain or other obvious blemishes or defects.
They can damage the machine and pose the
possibility of operator injury.
Figure 35. Table lock knob.
7. Keep your work area clear.
8. When making multiple passes through the
G1021Z 15" Planer
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Feed
Handwheel
The power feed features two feed rates; 16 FPM
and 20 FPM. When running the machine, the
operator can control the feed speed by moving
the feed control knob. Moving the knob toward the
machine produces the 20 FPM feed speed, away
from the machine produces 16 FPM and a center
position places the gear box in neutral. See
Figure 36.
Crank the handwheel to raise or lower the table
according to the desired workpiece thickness.
Make sure the height scale is properly adjusted.
Depth Limiter
NOTICE
The Model G1021Z is equipped with a depth lim-
iter located on the bottom of the cutterhead cast-
ing just under the nameplate. See Figure 37. The
The feed rate should be set while the plan-
er is running but before feeding lumber into
it. DO NOT attempt to change speeds after
the cutting operation has begun.
depth limiter controls maximum depth of cut to
1
/8".
With the limiting clip installed, you cannot cut
more than 1/8" in a single pass. While cutting this
much material is possible, it is not recommended.
Take it slow and easy.The quality of your work will
be better and your planer will last longer.
NOTICE
To avoid mechanical damage to the planer,
do not remove the depth limiter.
Figure 36. Feed speed adjustment knob.
NOTICE
Depth Limiter
If you take a cut that is too large, the planer
will bog down noticeably. The motor may
even stall. If this happens, turn off the
power immediately, lower the table, and
remove your workpiece. Re-adjust your
table to allow a lesser cut and repeat your
operation.
Figure 37. Location of depth limiter.
-30-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Test Run
Wood Species
Once the assembly is complete and the adjust-
ments are done to your satisfaction, you are
ready to test the machine.
The species of wood, as well as its condition,
have a dramatic effect on planing ability. The
harder the wood (as illustrated by its shear
strength), the more difficult it will be to plane. A
brief listing of common hard and soft woods in
relation to their shear strengths and planing diffi-
culty is listed below.
Turn on the power supply at the main panel.
Press the START button. Make sure that your fin-
ger is poised on the STOP button, just in case
there is a problem. The planer should run
smoothly, with little or no vibration or rubbing
noises. Strange or unnatural noises should be
investigated and corrected before operating the
machine further.
Type
Shear (PSI)
Black Locust
Sugar Maple
2,480
2,330
Pecan Hickory
White Oak
White Ash
Black Cherry
American Elm
Black Walnut
Red Alder
2,080
2,000
1,950
1,700
1,510
1,370
1,080
980
DO NOT attempt to investigate or adjust the
machine while it is running. Wait until the
machine is turned off, unplugged and all
working parts have come to a rest before
you do anything!
Basswood
Cottonwood
930
If noises occur that cannot be found by visual
inspection, feel free to contact our service depart-
ment for help.
Figure 38. Common hardwood shear strengths.
Type Shear (PSI)
Western Larch
Tamarack
1,410
1,280
1,160
1,130
1,150
1,050
1,000
940
Douglas Fir
Alaska Cedar
Sitka Spruce
Sugar Pine
Cypress
Redwood (OG)
Red Cedar
White Pine
Balsam Fir
Operation of this equipment has the poten-
tial to propel debris into the air which can
cause eye injury. Always wear safety glass-
es or goggles when operating equipment.
Everyday glasses or reading glasses only
have impact resistant lenses, they are not
safety glasses. Be certain the safety glass-
es you wear meet the appropriate stan-
dards of the American National Standards
Institute (ANSI).
860
850
710
Figure 39. Common softwood shear strengths.
G1021Z 15" Planer
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
Snipe can be minimized by proper adjustment of
the planer’s components, but complete removal
of snipe is extremely unlikely. More likely, you will
be able to reduce it to a tolerance of .002". If
snipe under that level is a problem, consider plan-
ing lumber longer than your intended work length
and cut off the excess after planing is completed.
Wood Characteristics
The species of wood, as well as condition, will
affect planing ability. The harder the wood, the
more difficult it will be to plane. We’ve included
below, a list of wood characteristics you may
encounter when planing. The following descrip-
tions of defects will give you some possible
answers to problems you may encounter while
planing different materials. Possible solutions fol-
low the descriptions.
Uneven Knife Marks - Uneven knife marks can
occur when the chipbreaker is set too high.
Inspect cutterhead bearings if re-adjustment of
the chipbreaker fails to remedy the situation.
Chatter Marks - Usually caused by incorrect
chipbreaker and pressure bar setting heights.
Chatter marks can also be caused by running a
narrow wood piece through the planer at either
the right or left end of the cutterhead. Chatter, like
uneven knife marks, will show in the form of a
''washboard'' look. Chatter marks are more likely
to be inconsistent in appearance than uneven
knife marks.
Chipped Grain - usually a result of cutting
against the grain, or planing wood with knots or
excessive amount of cross grain. Chipped grain
can also be caused by dull knives or misaligned
chipbreaker. Often, chipped grain can be avoided
by slowing down the feed rate and by taking shal-
low cuts. If those options do not work, inspect
your lumber and determine if its grain pattern is
causing the problem. If the wood does not show
substantial crossgrain, inspect your knives for
sharpness and inspect the chipbreaker for proper
alignment. See the Adjustment Section.
Wavy Surface - Caused by poor knife height
adjustment, wavy surface appears when one
knife is taking deeper cuts than the rest of the
knives. Remedy by re-setting the knives to a tol-
erance of ± .003".
Fuzzy Grain - Usually caused by surfacing lum-
ber with too high a moisture content. Sometimes
fuzzy grain is a characteristic of some woods,
such as basswood. Fuzzy grain can also be
caused by dull knives or an incorrect grinding
bevel. Check with a moisture meter. If moisture is
greater than 20%, sticker the wood and allow to
dry. Otherwise, inspect knife condition.
Pitch & Glue Build-up - Glue and resin build-up
on the rollers and cutterhead will cause over-
heating by decreasing cutting sharpness while
increasing drag in the feed mechanism. The
result can include scorched lumber as well as
uneven knife marks and chatter.
Chip Marks - Occur when chips aren’t properly
expelled from the cutterhead. The knives catch
the chips and drag them across the lumber being
planed. Chips tend to be random and non-uni-
form (as compared to chipped grain). Can be
caused by exhaust blockage or too much room
between the cutterhead and chip deflector. Using
a dust collection system in combination with the
planer can help reduce chip marks. Inspect the
chip deflector and readjust (as described earlier
in the text).
Glossy Surface - Usually caused by dull knives
taking shallow cuts at a slow feed speed. Surface
gloss will usually be accompanied by overheat-
ing. Often, lumber will be scorched and eventual-
ly, damage to knives will occur. If knives are sharp
on inspection, increase feed speed and/or cutting
depth.
Snipe - Occurs when board ends have more
material removed than the rest of the board.
Usually caused when one or both of the bed
rollers are set too high. Can also be caused by
the chipbreaker or pressure bar being set too
high. However, small amount of snipe is
inevitable.
-32-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: MAINTENANCE
Knives
General
Make a habit of inspecting your planer each time
you use it. Check for the following conditions and
repair or replace when necessary:
The inspection and setting of the planer knives is
covered extensively in Section 5: Adjustments.
1. Loose mounting bolts.
2. Worn switch.
3. Worn or damaged cords and plugs.
4. Damaged V-belts.
5. Any other condition that could hamper the
safe operation of this machine.
Table
The table and other non-painted surfaces on the
Model G1021Z should be protected against rust
and pitting. Wiping the table clean after every use
ensures that moisture from wood dust isn’t
allowed to trap moisture against bare metal sur-
faces.
Some woodworkers recommend using automo-
tive paste wax on exposed steel and cast iron sur-
faces. The wax provides a layer of protection, as
well as reducing friction between lumber and the
table, making cuts faster and smoother. Avoid
waxes that contain silicone or other synthetic
ingredients. These materials can find their way
into lumber that’s being worked, and can make
staining and finishing difficult. If you use paste
wax, make sure that it’s 100% Carnauba wax.
G1021Z 15" Planer
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
The Model G1021Z features factory-sealed bear-
ings. A sealed bearing requires no lubrication
during its lifetime. Should a bearing fail, your
planer will probably develop a noticeable rumble,
which will increase when the machine is put
under load. If allowed to get worse, overheating of
the journal containing the bad bearing could
occur. If the bad bearing is not replaced, it will
eventually seize - possibly doing damage to other
parts of the machine. Bearings are standard sizes
and can be replaced through Grizzly.
Fill
Drain
Figure 40. Gearbox fill and drain points.
Proper lubrication of other components of the
Model G1021Z are essential for long life and trou-
ble-free operation. Below is a list of components
that require periodic lubrication. Schedules are
based on daily use. Adjust accordingly for your
level of use.
Drive Chain - The drive chain should be inspect-
ed and lubricated monthly. Check sprocket, chain
and cotter pin during inspection. Use a general
purpose grease. Some chains will have master
links instead of cotter pins.
Columns/Lead Screws - The four columns
should be lubricated weekly with light oil.
Unfasten dust covers to gain access. The four
lead screws should be lubricated with general
purpose grease once a month.
Feed Rollers - The infeed/outfeed pressure
setscrews double as lubrication ports for the
rollers. See Figure 41. Add 1-2 drops of light
machine oil to all ports before each use. Daily
lubrication of feed rollers is crucial to the opera-
tion of your planer. Lubricate before start-up.
Apply a light oil, making sure that the lubricant
penetrates the bearing.
Worm Gear - The worn gear should be inspected
monthly and lubricated when needed. Remove
the worm gear box to inspect. See parts diagram
for location.
Chain - The table height adjustment chain should
be inspected monthly and lubricated when need-
ed. A good quality bicycle chain lubricant works
well for periodic lubrication.
Gear Box - Gear box oil should be drained after
the first 20 hours of operation. See Figure 40.
Replace with 80W-90 gear oil. Inspect levels peri-
odically and change yearly. Replace gear oil more
frequently under heavy use. Fill until oil reaches
the top of the filler plug port for correct oil level.
Figure 41. Feed roller lubrication points.
-34-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean and lubricate the chain sprockets as need-
ed. The gearbox oil should be checked before the
first use. It is full when oil begins dribbling out of
the fill hole. Oil should be replaced yearly. Use
80W-90 gear oil in normal situations. Use 50W
motor oil for unheated, winter shops. See
Adjustment Section.
Notes
The lead screws and columns should be wiped of
any grease and dust build up once a week. They
should be relubricated with light machine oil. See
Figure 42.
Lead Screw
Column
Figure 42. Lead Screw inside of column.
G1021Z 15" Planer
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: CLOSURE
The following pages contain parts diagrams, parts
lists, general machine data and warranty/return
information for your Model G1021Z Planer.
We recommend you keep a copy of our current
catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
machine, or if you need general assistance or
replacement parts, please contact the Service
Department listed in Section 3: GENERAL
INFORMATION.
If you need parts or help in assembling your
machine, or if you need operational information,
we encourage you to call the Grizzly Industrial
Service Department. Our trained service techni-
cians will be glad to help you.
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines, and your local
library are good places to start.
If you have comments dealing specifically with
this manual, please write to our Bellingham,
Washington location using the address in the
Introduction. The specifications, drawings, and
photographs illustrated in this manual represent
the Model G1021Z as supplied when the manual
was prepared. However, due to Grizzly’s policy of
continuous improvement, changes may be made
at any time with no obligation on the part of
Grizzly. Whenever possible, though, we send
manual updates to all owners of a particular tool
or machine. Should you receive one, add the new
information to this manual and keep it for refer-
ence.
The Model G1021Z was specifically
designed for wood cutting operations. DO
NOT MODIFY AND/OR USE THIS PLANER
FOR ANY OTHER PURPOSE. Modifications
or improper use of this tool will void the
warranty. If you are confused about any
aspect of this machine, DO NOT use it until
you have answered all your questions.
Serious injury may occur.
We have included some important safety mea-
sures that are essential to this machine’s opera-
tion. While most safety measures are generally
universal, Grizzly reminds you that each work-
shop is different and safety rules should be con-
sidered as they apply to your specific situation.
Like all power tools, there is danger associ-
ated with the Model G1021Z 15" Planer. Use
the tool with respect and caution to lessen
the possibility of mechanical damage or
operator injury. If normal safety precautions
are overlooked or ignored. Serious injury
may occur.
Always wear ANSI-approved safety glasses
or goggles and hearing protection when
operating equipment — particularly when
testing new tools or machinery. Do not allow
visitors into your workshop when testing or
operating equipment. Serious injury may
occur.
-36-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
This section covers the most common processing problems encountered in planing and what to do about
them. Do not make any adjustments until planer is unplugged and moving parts have come to a complete
stop. See the section on Wood Characteristics for additional troubleshooting information.
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Check power line for proper voltage.
Motor will not start.
1.
2.
Low voltage.
Open circuit in motor or loose 2.
connections.
Inspect all lead connections on motor for loose or open connec-
tions.
Motor will not start; fuses or 1.
Short circuit in line cord or plug. 1.
Short circuit in motor or loose 2.
connections.
Inspect cord or plug for damaged insulation and shorted wires.
Inspect all connections on motor for loose or shorted terminals or
worn insulation.
circuit breakers blow.
2.
3.
Incorrect fuses or circuit break- 3.
ers in power line.
Install correct fuses or circuit breakers.
Motor overheats.
1.
2.
Motor overloaded.
Air circulation through the motor 2.
restricted.
1.
Reduce load on motor.
Clean out motor to provide normal air circulation.
Motor stalls (resulting in 1.
blown fuses or tripped cir-
Short circuit in motor or loose 1.
connections.
Inspect connections on motor for loose or shorted terminals or
worn insulation.
cuit).
2.
3.
Low voltage.
Incorrect fuses or circuit break- 3.
ers in power line.
2
Correct the low voltage conditions.
Install correct fuses or circuit breakers.
4.
Motor overloaded.
4.
Reduce load on motor.
Machine slows when oper- 1.
ating. 2.
Feed rate too high.
Depth of cut too great.
1.
2.
Feed workpiece slower.
Reduce depth of cut.
Loud, repetitious noise com- 1.
ing from machine
Pulley setscrews or keys are 1.
Inspect keys and setscrews. Replace or tighten if necessary.
Tighten fan or shim cover.
Replace V-belt. See Maintenance.
missing or loose.
2.
3.
2.
3.
Motor fan is hitting the cover.
V-belt is defective
Machine is loud when cut- 1.
ting. Overheats or bogs 2.
down in the cut.
Excessive depth of cut.
Knives are dull
1.
2.
Decrease depth of cut.
Sharpen knives.
Infeed roller marks are left
on the workpiece.
Depth of cut too shallow.
Increase depth of cut.
Outfeed roller marks are left
on right side of workpiece.
Too much spring tension on feed
roller.
Refer to Feed Roller Pressure section for adjustment.
Cannot control snipe.
Long or heavy board sags as it
enters and exits.
Lift up on unsupported end of board as it enters and exits cutter-
head.
Chip buildup on outfeed
roller.
Chips working their way back
under the chip deflector.
Lay duct tape over the mounting bolts along the outside edge to
seal any possible gaps.
Move chip deflector back 1/8" to 1/4" from the cutterhead.
Machine howls on startup.
Chip deflector too close to the
cutterhead.
Table moves down while
cutting.
Knives dull
Replace knives.
G1021Z 15" Planer
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
-38-
G1021Z 15" Planer
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.We will then issue
you a “Return Number’’, which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
G1021Z 15" Planer
-39-
Download from Www.Somanuals.com. All Manuals Search And Download.
|