ADTRAN Year 2000 (Y2K) Readiness Disclosure
ADTRAN has established a Year 2000 program to ensure that our products will
correctly function in the new millennium. ADTRAN warrants that all products
meet Y2K specifications regardless of model or revision.
Information about ADTRAN’s Y2K compliance program is available at the fol-
lowing locations:
ADTRAN Web Site
Product Matrix
www.adtran.com
www.adtran.com/y2kfax.html
Faxback Document Line (256) 963-8200
Y2K plans and product certifications are
listed in the matrix.
(256) 963-2200
Y2K Project Line
E-mail
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These lim-
its are designed to provide reasonable protection against harmful inter-
ference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio frequencies. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Shielded cables must be used with this unit to ensure compliance with
Class A FCC limits.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to op-
erate the equipment.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus as set out in the interference-causing
equipment standard entitled “Digital Apparatus,” ICES-003 of the De-
partment of Communications.
Cet appareil nuerique respecte les limites de bruits radioelectriques ap-
plicables aux appareils numeriques de Class A prescrites dans la norme
sur le materiel brouilleur: “Appareils Numeriques,” NMB-003 edictee
par le ministre des Communications.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN EQUIPMENT LIMITATIONS
The Industry Canada Certification label identifies certified equipment.
This certification means that the equipment meets certain telecommu-
nications network protective, operational, and safety requirements.
The Department does not guarantee the equipment will operate to the
user's satisfaction.
Before installing this equipment, users should ensure that it is permissi-
ble to be connected to the facilities of the local telecommunications com-
pany. The equipment must also be installed using an acceptable method
of connection. In some cases, the company's inside wiring associated
with a single line individual service may be extended by means of a cer-
tified connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Cana-
dian maintenance facility designated by the supplier. Any repairs or al-
terations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to re-
quest the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
waterpipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should con-
tact the appropriate electric inspection authority, or an electrician, as appropri-
ate.
The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which is
used by the device, to prevent overloading. The termination on a loop
may consist of any combination of devices subject only to the equipment
that the total of the LNs of all devices does not exceed 100.
The ringer equivalence number (REN) assigned to each terminal adapter
is used to determine the total number of devices that may be connected
to each circuit. The sum of the RENs from all devices in the circuit
should not exceed a total of 5.0.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes provide additional useful information.
Cautions signify information that could prevent service inter-
ruption.
Warnings provide information that could prevent damage to the
equipment or endangerment to human life.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
When using your telephone equipment, please follow these basic safety precau-
tions to reduce the risk of fire, electrical shock, or personal injury:
1. Do not use this product near water, such as near a bath tub, wash bowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical
storm. There is a remote risk of shock from lightning.
3. Do not use the telephone report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the
manual. Do not dispose of batteries in a fire. They may explode. Check
with local codes for special disposal instructions.
SAVE THESE INSTRUCTIONS
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Customer Service
ADTRAN will replace or repair this product within five years from
the date of shipment if the product does not meet its published
specifications or if it fails while in service. For detailed warranty,
repair, and return information refer to the ADTRAN Equipment
Warranty and Repair and Return Policy Procedure.
Return Material Authorization (RMA) is required prior to returning
equipment to ADTRAN.
For Service, RMA requests, or more information, contact ADTRAN
Customer Service listed on the inside back cover of this manual.
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents ...................................................................................................... xi
List of Figures......................................................................................................... xvii
List of Tables........................................................................................................... xix
Chapter 1
Introduction..................................................................................... 1-1
ESU 120e Overview .................................................................................................. 1-1
ESU 120e Features .............................................................................................1-2
ESU Option Modules ........................................................................................1-2
Option Module Architecture ...........................................................................1-3
ESU 120e Configuration Applications ................................................................... 1-3
Router, PBX Application ...........................................................................1-3
Chapter 2
Installation....................................................................................... 2-1
Unpack, Inspect, Power Up .................................................................................... 2-1
Receipt Inspection .............................................................................................2-1
ADTRAN Shipments Include ..........................................................................2-1
Customer Provides ............................................................................................2-1
Power Connection .............................................................................................2-2
Grounding Instructions ........................................................................................... 2-2
Identification of Rear Panel Layout ....................................................................... 2-4
ESU120e Interfaces ................................................................................................... 2-5
Network Interfaces ............................................................................................2-5
Network Test Interface ..............................................................................2-5
Nx56/64 Serial Interface ...........................................................................2-5
Drop (PBX) Interface ..................................................................................2-6
Control Port Input ......................................................................................2-6
Chain Port Output .....................................................................................2-6
10BaseT Interface .......................................................................................2-6
Power-Up Testing ..................................................................................................... 2-6
Self-Test ..............................................................................................................2-6
Initialization .......................................................................................................2-7
61200420L1-1
ESU 120e User Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Set User Passcode ...................................................................................... 2-7
Set Unit Identification ............................................................................... 2-7
Set Control Port ......................................................................................... 2-8
Chain In (PC) ............................................................................................. 2-8
Chain In/Chain Out ................................................................................. 2-8
Normal Power-Up Procedure .................................................................................2-9
Chapter 3
Operation ........................................................................................ 3-1
Front Panel .................................................................................................................3-1
LED Descriptions ........................................................................................... 3-3
DSU/Drop Status ...................................................................................... 3-3
Module Status ............................................................................................ 3-4
Operation keys .................................................................................................. 3-4
General Menu Operation ................................................................................ 3-5
Set the Data Field ....................................................................................... 3-6
Data Port Identification ................................................................................... 3-7
Front Panel Menu Structure ............................................................................ 3-7
Alternate Methods of Control ......................................................................... 3-8
Terminal Mode ........................................................................................ 3-10
Telnet ......................................................................................................... 3-10
Chapter 4
Active Alarms ................................................................................................... 4-3
View History ..................................................................................................... 4-4
Port Status .......................................................................................................... 4-5
0.1 Nx56/64 Menu Items .......................................................................... 4-5
DTE Data/CK .............................................................................. 4-5
Port Rate ....................................................................................... 4-5
0.2 Drop Menu Items (DSX Errors) .......................................... 4-6
Remote Port ....................................................................................................... 4-6
Clear Port Alarm ............................................................................................... 4-6
ENET Status ...................................................................................................... 4-6
xii
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Network (NI) ............................................................................................................. 5-3
Network (NI) Menu Items ...............................................................................5-3
ESU 120e Clock Sources .......................................................................................... 5-5
Network Timed .................................................................................................5-6
Base Drop Timed ...............................................................................................5-7
Base DTE Timed ................................................................................................5-8
Internal Timing ..................................................................................................5-9
Normal (CSU) Timing ....................................................................................5-10
Unit Menu ........................................................................................................5-11
Map Exchange (Map Xchng) ........................................................................5-13
Map In Use: A(B) ............................................................................................5-13
TS0 Map A and TS0 Map B ............................................................................5-14
Port Configuration (Port Config) .................................................................5-17
Chapter 6
Utility Menu.................................................................................... 6-1
Time/Date ..........................................................................................................6-2
Factory Restore ..................................................................................................6-2
Set Passcode .......................................................................................................6-2
Change/Set a Passcode .............................................................................6-3
Special Feature ............................................................................................6-3
No Passcode Desired .................................................................................6-3
Unit ID ................................................................................................................6-4
To Set the Unit Identification ...................................................................6-4
No Unit ID Desired ....................................................................................6-4
Software Revision (Software Rev) ..................................................................6-4
Port Utility ..........................................................................................................6-5
Enet Address ......................................................................................................6-5
CMD Mode .........................................................................................................6-5
Chapter 7
Test Menu ........................................................................................ 7-1
Network Tests ....................................................................................................7-2
Loopback Tests ..................................................................................................7-2
Network Interface Loopbacks ..................................................................7-2
LOCAL LOOPBCK ....................................................................................7-3
REMOTE LOOPBCK .................................................................................7-3
TEST PATTERN .........................................................................................7-3
All Ones .........................................................................................7-3
61200420L1-1
ESU 120e User Manual
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
PATTERN RESULT ................................................................................... 7-5
Run Self-Test ..................................................................................................... 7-6
Port Tests ........................................................................................................... 7-7
Port Test Menu Items for 0.1 Nx56/64 ................................................... 7-8
Cancel Tests ....................................................................................................... 7-9
Chapter 8
Main Menu ................................................................................................................8-1
Remote Menu Access ....................................................................................... 8-4
Management Configuration ....................................................................................8-4
SNMP Read Community ................................................................................. 8-4
SNMP Trap Community ................................................................................. 8-5
Host 1 Trap IP Address ............................................................................ 8-5
Host 2 Trap IP Address ............................................................................ 8-5
Host 3 Trap IP Address ............................................................................ 8-5
Host 4 Trap IP Address ............................................................................ 8-5
System Name ............................................................................................. 8-5
System Contact .......................................................................................... 8-5
System Location ......................................................................................... 8-5
Auth. Fail Traps Sent ............................................................................... 8-6
Poll Link Status Traps Sent ...................................................................... 8-6
Ping IP Host ............................................................................................... 8-6
Telnet/Terminal Timeout ........................................................................ 8-6
Telnet/Terminal Password ...................................................................... 8-6
Exit ............................................................................................................... 8-6
Flash Download ................................................................................................ 8-7
Quit Session ....................................................................................................... 8-7
xiv
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP ................................................................. A-1
Appendix B. Connector Pinouts .........................................................................B-1
Appendix C. System Messages ...........................................................................C-1
Appendix D. Specifications ................................................................................ D-1
Index ................................................................................................................. Index-1
61200420L1-1
ESU 120e User Manual
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
xvi
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1-1. Router, PBX, Application Set Up ......................................................1-3
Figure 2-1. ESU 120e Rear Panel ...........................................................................2-4
Figure 2-2. ESU 120e Interfaces .............................................................................2-5
Figure 2-3. Example of Chain In ...........................................................................2-8
Figure 3-1. ESU 120e Front Panel Layout ............................................................3-2
Figure 4-1. Status Menu Tree ................................................................................4-1
Figure 4-3. Display of Alarm Messages ...............................................................4-4
Figure 5-1. Configuration Menu Tree ..................................................................5-2
Figure 5-2. Network Timed Clock Source ...........................................................5-6
Figure 5-3. Drop Timed Clock Source .................................................................5-7
Figure 5-4. Network Timed Clock Source ...........................................................5-8
Figure 5-5. Internal Clock Source .........................................................................5-9
Figure 5-6. Normal (CSU) ....................................................................................5-10
Figure 5-7. DS0 Map Designations .....................................................................5-14
Figure 5-8. Create Temp Selection Screen .........................................................5-15
Figure 6-1. Utility Menu Tree ................................................................................6-1
Figure 7-1. Test Menu Tree ....................................................................................7-1
Figure 7-2. Network Loopback Tests ...................................................................7-3
Figure 8-1. Telnet/Terminal Main Menu ............................................................8-1
Figure 8-2. TS0 Temp Map ....................................................................................8-2
61200420L1-1
ESU 120e User Manual
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
lxviii
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. Normal Mode of Operation .............................................................5-19
Table B-1. Network Pinouts ................................................................................ B-1
Table B-2. Control In/Chain-in Pinout ............................................................. B-2
Table B-3. Chain-Out Connector Pinout .......................................................... B-3
Table B-4. Nx56/64 Pin Assignments for EIA-530 and V.36 .......................... B-4
Table B-5. Nx56/64 Pin Assignments for V.35 Mode ..................................... B-5
Table B-6. Adapter Cable, DB 25 to V.35, 34-Pin Winchester ........................ B-6
Table B-7. Nx56/64 Pin Assignments for V.11/x.21 Mode ............................ B-7
Table B-8. Adapter Cable DB25 to X.21, DB15 Connector .............................. B-8
Table B-9. Pinout Connectors for Terminal Interface ...................................... B-8
Table B-10. 10BaseT Pinout ................................................................................... B-9
61200420L1-1
ESU 120e User Manual
xix
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
xx
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Chapter 1
ESU 120E OVERVIEW
The ESU 120e is an E1/FE1 multiplexer with an Nx56/64 data port,
a drop (PBX) interface, one option slot, and embedded SNMP man-
agement. The ESU 120e’s option slot accepts one of many available
option modules for voice and data applications.
The ESU 120e serves as the link between user data sources such as
local area network (LAN) bridges and routers, computers, CAD
systems, teleconferencing equipment, and PBXs. Through the use
of multiple data ports, the ESU 120e can simultaneously connect
one or more of these devices to a E1 circuit. The amount of band-
width allocated to each port is custom-programmable. You can
manually allocate bandwidth or set the bandwidth to automatically
change at predetermined times to use the available bandwidth
most advantageously. Changes in the configuration do not disrupt
data flow in channels that are not being reconfigured. The unique
architecture and the availability of option modules provides a path
for growth to accommodate future requirements.
The ESU 120e offers a wide variety of network management
options. You can manage via SNMP through the 10BaseT or chain-
in ports. If you are using T-Watch Pro, a Microsoft Windows® pro-
gram, you can manage the ESU 120e via the same 10BaseT or chain-
in ports. An enhanced VT-100 terminal interface is also provided.
61200420L1-1
ESU 120e User Manual
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
ESU 120e Features
The following list describes the standard features in the ESU 120e.
•
•
•
A single E1 interface
An Nx56/64 data port and G.703 drop port interface
Data port supports V.35, EIA-530, V.36 and X.21 electrical inter-
faces
•
•
•
•
An inband communication channel requiring only 8k of band-
width from a single TS0
One option slot to house option modules with up to four addi-
tional ports, including voice and data
Allows mix of port types to meet the data interface require-
ments.
Easy configuration capabilities using simplistic menus dis-
played in a liquid crystal display (LCD) window operated by a
front panel keypad
•
Two programmable configuration maps that define the band-
width allocation between data ports
•
•
Flash memory for software updates
Selectable timing from the network, from the Nx56/64 or drop
ports, internally, or from a secondary interface
•
•
QRSS; 511 test patterns using Nx option
Extensive self-test and monitoring provides assurance of proper
operation
•
SNMP, Telnet, and T-Watch Pro Management via SLIP or
10BaseT
ESU Option Modules
Some of the option modules available for the ESU 120e are:
•
•
•
Nx56/64 serial interface. This module provides a V.35 serial in-
terface in either single or dual versions.
Router module. Integrated IP/IPX Router with 10BaseT inter-
face.
NxIQ. Provides extensive frame relay and monitoring capabil-
ities.
1-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
Option Module Architecture
The ESU 120e features a unique architecture that allows the addi-
tion of one option module and plug-on board providing an oppor-
tunity for growth to accommodate another application.
ESU 120E CONFIGURATION APPLICATIONS
The following examples illustrate possible configurations of
ESU 120e applications.
Router, PBX Application
In this application, the base Nx54/64 provides a V.35 interface to a
router. The PBX is interfaced to the ESU 120e with the base drop
interface. The 10BaseT port allows SNMP network management
over the LAN. See Figure 1-1.
PBX
ESU 120e
ENTER
1
2
3
4
5
6
ALARM
7
CLEAR
8
CANCEL
COPY
9
HOME
0
SHIFT
#
10 BaseT LAN
SNMP NETWORK
MANAGEMENT WORKSTATION
Figure 1-1. Router, PBX, Application Set Up
61200420L1-1
ESU 120e User Manual
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
1-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Chapter 2
UNPACK, INSPECT, POWER UP
Receipt Inspection
Carefully inspect the ESU 120e for any shipping damages. If you
suspect damage, file a claim immediately with the carrier and then
contact ADTRAN Customer Service (see inside the last page of this
manual). If possible, keep the original shipping container for use in
shipping the ESU 120e back for repair or for verification of damage
during shipment.
AD TRAN Shipments Include
•
The ESU 120e
•
•
A DB-25 to modular adapter for VT-100 and T-Watch access.
An 8-position modular cable for connection to the chain-in port
(6 ft.)
•
The user manual
Customer Provides
•
•
Power cord
Cable(s) for connection to either the 120 Ω DB15 or 75 Ω BNC
network interfaces
•
•
Cables for any expansion modules to be used with the ESU 120e
10BaseT cable for connection to a LAN or router (if you plan to
use remote management features)
61200420L1-1
ESU 120e User Manual
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Power Connection
Power is supplied to the ESU 120e through a IEC-type power con-
nector on the rear of the unit.
Power to the ESU 120e must be from a grounded 90-240 VAC,
50/60Hz source.
GROUND ING INSTRUCTIONS
Grounding instruction information from the Underwriters' Labora-
tory UL 1950 3rd Edition is provided in this section.
An equipment grounding conductor that is not smaller in size than
the ungrounded branch-circuit supply conductors is to be installed
as part of the circuit that supplies the product or system. Bare, cov-
ered, or insulated grounding conductors are acceptable. Individu-
ally covered or insulated equipment grounding conductors shall
have a continuous outer finish that is either green, or green with
one or more yellow stripes. The equipment grounding conductor is
to be connected to ground at the service equipment.
The attachment-plug receptacles in the vicinity of the product or
system are all to be of a grounding type, and the equipment
grounding conductors serving these receptacles are to be connected
to earth ground at the service equipment.
A supplementary equipment grounding conductor shall be
installed between the product or system and ground that is in addi-
tion to the equipment grounding conductor in the power supply
cord.
The supplementary equipment grounding conductor shall not be
smaller in size than the ungrounded branch-circuit supply conduc-
tors. The supplementary equipment grounding conductor shall be
connected to the product at the terminal provided, and shall be
connected to ground in a manner that will retain the ground con-
nection when the product is unplugged from the receptacle. The
connection to ground of the supplementary equipment grounding
conductor shall be in compliance with the rules for terminating
bonding jumpers at Part K or Article 250 of the National Electrical
2-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Code, ANSI/NFPA 70. Termination of the supplementary equip-
ment grounding conductor is permitted to be made to building
steel, to a metal electrical raceway system, or to any grounded item
that is permanently and reliably connected to the electrical service
equipment ground.
Bare, covered, or insulated grounding conductors are acceptable. A
covered or insulated grounding conductor shall have a continuous
outer finish that is either green, or green with one or more yellow
stripes.
The supplemental grounding conductor shall be connected to he
equipment using a number 8 ring terminal. The terminal should be
fastened to the grounding lug provided on the rear panel of the
equipment. The ring terminal should be installed using the appro-
priate crimping tool (AMP P/N 59250 T-EAD Crimping Tool or
equivalent).
61200420L1-1
ESU 120e User Manual
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
ID ENTIFICATION OF REAR PANEL LAYOUT
Figure 2-1 shows the configuration of the rear panel of the ESU
120e.
4
6
2
5
1
3
12
9
10
7
8
11
1 Network 120 Ω Connector
7 Control In/Out Connection
2 Network Receive Monitor Jack
3 Drop Port Connector (To PBX)
4 Option Slot
8 10BaseT Connector (To LAN for Management)
9 Network 75 Ω Receive Connector
10 Network 75 Ω Transmit Connector
11 Data Port Connector
5 Power Switch
6 IEC Power Connector
12 Fuse Tray
Figure 2-1. ESU 120e Rear Panel
2-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
ESU120E INTERFACES
The ESU 120e is equipped with an Nx56/64 data port, a G.703 drop
interface, an option slot, management interfaces, and an E1 inter-
face in the rear panel. See Figure 2-2.
10BaseT LAN
PC or Modem
Control
Input
Chain
Output
Chain
Input
Chain
Output
ESU 120e
ESU 120e
NI
NI
Drop
Network
Drop
Nx56/64
Nx56/64
Option
Option
V.35
RS530, V.11
PBX-1
PBX
V.35
RS530, V.11
Figure 2-2. ESU 120e Interfaces
Network Interfaces
The Network Interface (NI) port provides the connection to the E1.
This port complies with the applicable ANSI and CCITT standards.
Either the 120Ω DB15 or the 75Ω BNC interface may be used for
the Network Interface. The 75/120 selection must be made with
the front panel menus. For more information see Wiring on page B-
1.
Network Test Interface
The MON test jack provides a bridged access jack for non-intrusive
monitoring of the incoming E1.
Nx56/ 64 Serial Interface
The Nx56/64 provides a serial interface that operates from 56kbps
to 1.984Mbps. The Nx56/64 can be configured as a V.35, V.36, EIA-
530, or V.11 electrical interface through the front panel menus. This
port provides 511 pattern generation and detection, as well as
remote loopback capability.
61200420L1-1
ESU 120e User Manual
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
D rop (PBX) Interface
The drop interface provides a G.703 interface for a PBX or other
equipment.
Control Port Input
The control port input provides an EIA-232 input from a PC or a
modem for control of the ESU 120e. You can also use it as a chain
input from another ESU 120e or ESU 100. For more information see
Wiring on page B-1.
Chain Port Output
to other ESU 120es. For more information see Wiring on page B-1.
10BaseT Interface
The 10BaseT interface provides the LAN interface for managing the
ESU 120e with SNMP or T-Watch Pro. For more information see
Wiring on page B-1.
POWER-UP TESTING
When shipped from the factory, the ESU 120e is set to factory
default conditions. At the first application of power, the unit auto-
matically executes a memory self-test. A full self-test can be run
from the front panel, and a pass code and unit ID may be set using
the UTIL menu.
Self-Test
Upon a power-up, the LCD displays Memory Test Now Testing
and the Test LEDs are illuminated. When the self-test is completed
with no failures detected, the OK LED lights up and the LCD
momentarily displays All Tests Passed. If a failure is detected, a
list of failures is displayed in the LCD window. The full self-test
procedure (invoked from the front panel or T-Watch PRO) consists
of the following tests:
2-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Board-level tests
Each of the ESU 120e boards contains an on- board processor which
executes a series of tests checking the circuitry on the board.
•
RAM and EPROM tests.
•
Verify on-board circuitry.
Unit-level tests
•
Front panel LED verification.
•
Board-to-board interface test. A test pattern is sent from the
controller through a loopback on all other boards and checked
on the controller. This verifies the data path, clocks, and control
signals for the entire chassis.
Initialization
Set User Passcode
The ESU 120e is designed to operate with or without the use of a
passcode. The default condition is without a passcode.
must enter a passcode. When managing a number of units, the
passcode can be the same for all the units.
The passcode should be a number easily remembered. Once
entered, the passcode is required to access any operation other than
viewing. See Set Passcode on page 6-2 for details.
Set Unit Identification
The Unit ID sets the unit to respond to remote control (controlled
by a device other than the front panel or terminal). If no Unit ID is
recorded it is not possible to operate from any remote control
device, including the local PC for T-Watch PRO or SNMP. See Unit
ID on page 6-4 for details.
61200420L1-1
ESU 120e User Manual
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Set Control Port
The ESU 120e can be configured from the control port when T-
Watch PRO, SNMP, or the terminal interface are being used.
If the control port is to be used, the control port baud rate must also
be selected.
Chain In (PC)
The unit can be controlled from an external PC connected directly
or via modem to the chain-in port. when using chain-in, the selec-
tion of the control port baud rate from 9600 (factory default), 1200,
2400, or 4800, or 38400 must be made using the Unit Configuration
menu. See Unit Menu on page 5-11 for details.
Unless locked out externally, the front panel can also control the
unit.
Chain In/ Chain Out
ESU 120e units and other ESUs can be linked together to form a
chain. Figure 2-4 shows an example of a chain-in arrangement with
a PC or a modem. The first ESU 120e in the chain receives control-
ling input from the PC or modem.
PC or Modem
Chain
In
Chain
Out
Control
Input
Chain
Out
Chain
In
Chain
Out
ESU 120e
ESU 120e
ESU 120e
Figure 2-3. Example of Chain In
2-8
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Subsequent ESUs in the chain are in a position to intake informa-
tion from another ESU. This in-taking of information from another
ESU in the chain is identified as chain in. The baud rate for the
chained units must match that of the first unit.
Unless locked out externally, the front panel can also control the
unit.
At this point, the Unit Initialization procedure is concluded. If the
unit is to be configured remotely, there are no additional items nec-
essary to complete prior to executing remote configuration.
The Passcode, the Unit ID, and the Control Port settings are stored
in a nonvolatile memory. This assures they are operable for subse-
quent power-up sequences.
NORMAL POWER-UP PROCED URE
After the unit has been put into operation with the initial power-up
and initialization, subsequent power-up procedure includes only
the Power-Up self-test followed by the request for a passcode
(password) if this option was selected during initialization.
Use the number keys to enter the previously recorded passcode fol-
lowed by pressing Enter.
61200420L1-1
ESU 120e User Manual
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
2-10
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
O peration
Chapter 3
FRONT PANEL
The ESU 120e front panel monitors operation and controls the con-
figuration of the unit. The ESU 120e front panel is shown in Figure
3-1. Descriptions of each part of the front panel follow.
Name
Description
LCD Window
Displays menu items and messages in two lines by 16
characters. It also displays alarm and status information.
Enter Key
Selects active menu items. To select a menu item, press the
number of the item. The menu item flashes, indicating it is
activated. Press Enter to select the menu item.
Up and Down
Arrows
Up and Down Arrows scroll through and activate the
submenu items available in the current menu. When the
submenu items are scrolled, the flashing cursor indicates the
active parameters.
Cancel Key
Pressing the Cancel key stops the current activity and returns
to the previous menu. Repeat until the desired menu level is
exit the current display and return to the previous menu.
Numeric
Keypad
The numeric keypad contains the numbers 0 through 9 which
are used to activate menu items and enter information (such
as the IP address).
Shift(entering
special function
keys)
Enter special function keys by pressing and holding Shift
before pressing the key representing the desired character. See
Operation Keys on page 3-4 for a description of the function
keys. To activate a special function key rather than a number,
press Shift and then the button. If a key is pressed without
using Shift, the numbered item becomes active instead of the
special function key.
61200420L1-1
ESU 120e User Manual
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
4
2
5
1
3
6
14
15
16
17
10
13
20
18
19
9
8
12
11
7
Figure 3-1. ESU 120e Front Panel Layout
No
Name
Description
Displays menu items and messages
1
2
3
4
5
6
7
8
9
LCD Window
Enter
Selects active menu item
Up and Down Arrows
Alarm
Scrolls through/activates submenu items
Quick access to the active alarm display menu
Clears data/results fields
Clear
Shift
Provides access to special function keys
DSU/Drop
OK (DSU/Drop status)
Test (DSU/Drop Status)
Data and Drop parts is in normal mode with no errors
Active when Data or Drop Port is in test mode
10 Alarm (DSU/Drop Status) Active when alarm condition has been detected on Data or Drop Port
11 OK (Module Status)
12 Test (Module Status)
13 Alarm (Module Status)
14 Cancel
Operation is in normal mode with no detected errors
Active when the module is in test mode
Active when an alarm condition has been detected
Stops current activity and returns to the previous menu
Copies last data entered into the current TS0
Operation is in normal mode with no detected errors
Active when network interface is in test mode
Indicates errors such as BPV, OOF, and CRC
Returns to main menu
15 Copy
16 OK (CSU Status)
17 Test (CSU Status)
18 Error (CSU Status)
19 Home
20 Alarm (CSU Status)
Active when alarm condition detected on the network interface
3-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
LED D escriptions
CSU Status
The CSU status LEDs display the operational condition of the network
interface located on the controller board in the unit.
Name
Description
OK (green)
Indicates the operation is in the normal mode and no
errors have been detected.
Test (yellow) Indicates that the network interface is operating in a test
mode. This includes a self-test or a test loopback.
When lighted, this LED also indicates that normal data
flow is not occurring on the network interface.
Error (red)
Indicates an error such as a BPV, OOF, or CRC.
Alarm (red) Indicates an alarm condition has been detected. When
the alarm condition is no longer valid, the OK LED
activates (turns on). To view an alarm condition, select
the active alarm menu item or select Alarm by pressing
Shift 8. If the alarm conditions have been corrected, the
alarm which caused the activation of the Alarm LED
can be viewed under the Unit History menu.
DSU/Drop Status
Name
Description
OK (green)
Indicates the operation is in the normal mode and no
errors have been detected.
Test (yellow) Indicates that the interface is operating in a test mode.
This includes a self-test or a test loopback. When
lighted, this LED also indicates that normal data flow is
not occurring in at least one of the module ports.
Alarm (red) Indicates an alarm condition has been detected. When
the alarm condition is no longer valid, the OK LED
activates (turns on). To view an alarm condition, select
the active alarm menu item or select Alarm by pressing
Shift 8. If the alarm conditions have been corrected, the
alarm which caused the activation of the Alarm LED
can be viewed under the Unit History menu.
61200420L1-1
ESU 120e User Manual
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
Module Status
Name
Description
OK (green)
Indicates the operation is in the normal mode and no
errors have been detected.
Test (yellow) Indicates that one of the interfaces is operating in a test
mode. This includes a self-test or a test loopback.
When lighted, this LED also indicates that normal data
flow is not occurring in at least one of the module ports.
Alarm (red) Indicates an alarm condition has been detected. When
the alarm condition is no longer valid, the OK LED
activates (turns on). To view an alarm condition, select
the active alarm menu item or select Alarm by pressing
Shift 8. If the alarm conditions have been corrected, the
alarm which caused the activation of the Alarm LED
can be viewed under the Unit History menu.
Operation keys
Name
Description
Copy
Used in the TS0 mapping menu operations to copy the
last data entered into the current TS0. This key operates
without pressing the Shift key.
Home
Alarm
Returns home to the Main menu from any menu
location.
Used as quick access to the active alarm display menus.
This can be activated while any other menu item is in
use. When the Alarm menu is exited, the unit returns to
the location of the same menu that was active when
Alarm was selected.
Clear
Used in various menus to clear data/result fields.
3-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
General Menu Operation
The ESU 120e uses a multilevel menu structure containing both
menu items and data fields. All menu operations and data are dis-
played in the LCD window. The menu items are numbered and can
be viewed by scrolling with the Up and Down arrows.
Name
Description
Data Field
You can edit menu items followed by a colon (:).
Display
Only Field
You cannot edit menu fields followed by an equal
symbol (=). This symbol identifies a field used for value
display only.
Arrows
Menus that display small Up or Down Arrows in the
lower right corner indicate there are more menu items
than are visible on a two-line LCD. Access the
additional items with the up or down arrows. You can
also access undisplayed menu items by using the
appropriate menu number.
Select and Activate a Menu Item
To choose menu items, place the cursor on the desired menu item by
pressing the number corresponding to the menu item or highlighting
the menu item with the Up and Down Arrow. The following procedure
describes how to activate the Alarm List option from the Status Menu.
Step
Action
Result
1
Activate the STATUS menu
using the arrow keys or by
pressing 1.
The cursor will flash on the
number next to the activated
selection.
2
3
Press Enter.
Use the arrow keys to view
submenu items.
Choose an item on the
submenu such as ACTIVE
ALARMS.
4
5
Select the submenu with the
arrow keys or by pressing 3.
Press Enter.
View the Alarm List using the
arrow keys.
61200420L1-1
ESU 120e User Manual
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
The menu tree below shows front panel menu travel.
1) NI PERF RPTS
2) NI ERRORS
3) ACTIVE ALARMS
4)VIEW HISTORY
5) PORT STATUS
6) REMOTE PORT
7) CLEAR PORT ALM
8) ENET STATUS
(ALARM LIST)
END OF LIST
1)STATUS
Figure 3-2. Example of Basic Front Panel Menu Travel
Set the D ata Field
You can edit data fields preceded by a colon (:).
Step
Action
Result
1
With the cursor positioned on The cursor moves to the data
the submenu item number,
press Enter.
field, (to the right of the
submenu item name).
2
3
Using the arrows, scroll to scan The value settings display
the available value settings.
one-at-a-time in the data field
position.
When the desired value is
displayed in the data field
When the value is set, the
cursor moves back to the
position, press Enter to set that submenu item position
value.
indicating the operation is
complete.
4
Select another submenu field
Pressing Cancel prior to
or press Cancel to return to the pressing Enter voids any data
submenu.
changes. The original data
value is restored and the
cursor returns to the submenu
field.
3-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
Exit Any Menu Field Operation Or D isplay
Press Cancel as many times as required to return to the desired
menu level or press Home to return to the main menu.
D ata Port Identification
When configuring the unit, menu selections will include options
from data port submenus. Selecting of data ports is necessary
because the ESU 120e uses a Slot-Port method to identify which
data port the menu item is referencing. If a module containing a
PBX drop option card with an Nx56/64 plug-on interface is
installed in the option slot, it would be designated as:
drop Passthru=1.1
Where slot=1 and port =1.
The drop is located in the option slot and is the first port in that
slot.
Nx56/64=1.2
Where slot=1 and port=2.
The Nx is located in the slot and is the second port in that slot.
The ports that are built into the ESU 120e are referenced as Slot 0.
The Nx56/64 would be designated as 0.1 and the drop would be
referenced as 0.2.
Front Panel Menu Structure
The ESU 120e uses a multilevel menu structure containing both
menu items and data fields. All menu operations and data display
in the LCD window.
The opening menu is the access point to all other operations. Each
Main menu item has several functions and submenus to identify
and access specific parameters.
61200420L1-1
ESU 120e User Manual
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
The front panel LCD of the Main menu contains four options:
Status, Config, Util and test.
Name
Description
Status
The Status Menu displays all relevant information
for the network and DTE interfaces. For detailed
information on status options, see Status Menu in
Chapter 4.
Config
(Configuration)
The Configuration Menu displays and sets the ESU
120e operational configuration, including all
network interface parameters, the allocation of the
TS0s, and the port parameters. For detailed
information on configuration options, see
Configuration Menu in Chapter 5.
Util (Utilities)
Test
The Utility Menu displays and sets system
parameters. For detailed information on utility
options, see Utility Menu in Chapter 6.
The Test Menu initiates different types of unit tests
and displays test results in the LCD window. For
detailed information on test options, see Test Menu
in Chapter 7.
Alternate Methods of Control
T-Watch PRO (AD TRAN PC Program)
T-Watch PRO is the ADTRAN PC control program. It provides
complete control over the configuration of the ESU 120e using a
graphical interface. The T-Watch PRO program displays the same
status and performance data as the front panel LCD. This data is
displayed in the form of tables and graphs.
The T-Watch PRO program has the following capabilities:
•
Interfaces with a modem which permits dialing into a remote
ESU 120e location to configure the unit or read the status or per-
formance of the unit.
•
•
Receives traps from any ESU product.
Records and creates display performance data over a 30-day
period.
•
Accesses units via the local area network.
3-8
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
To set up the ESU 120e to work with T-Watch PRO over the LAN,
follow these steps:
Step
Action
1
Set the Unit ID using the Front Panel. See Unit ID on
page page 6-4 for details.
2
3
4
Set TCP/IP interface to 10BaseT (or SLIP) using the
Front Panel.
Configure the IP address, default gateway, and subnet
mask using the Front Panel.
Follow the installation instructions for T-Watch PRO to
start the program and connect to the unit.
To set up the ESU 120e to work with T-Watch PRO over a direct
EIA-232 connection, the following steps are required:
Step
Action
1
Set the Unit ID and set a passcode using the Front Panel.
See Unit ID on page 6-4 and Set Passcode on page 6-2
for details.
2
3
Set the control port rate to the same setting as the PC
Com port.
Connect the PC Com port to the Chain-In port on the
ESU 120e using the DB25 adapter and modular cable
provided.
4
Follow the installation instructions for T-Watch PRO to
start the program and connect to the unit.
61200420L1-1
ESU 120e User Manual
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. O peration
SNMP
The ADTRAN ESU 120e supports the Simple Network Manage-
ment PROtocol (SNMP) through the 10BaseT or chain in (SLIP)
interface. See Appendix A, for information on SNMP.
To use SNMP with the ESU 120e, do the following:
Step
Action
1
Set TCP/IP access as either 10BaseT or SLIP (Chain In
Port).
2
3
Set the IP address, default gateway, and subnet mask
through the front panel.
The appropriate MIB browser must be loaded into the
Network Management Station (available on the
ADTRAN webpage at http://www.adtran.com).
The MIB browser issues SNMP gets/sets to the ESU
120e
Terminal Mode
The ESU 120e provides the front panel menus to a VT-100 type ter-
minal. This mode can be used to configure and monitor the unit.
Initiate this mode by typing <CTRL> PTT on the terminal once it is
connected to the Control In port. For detailed information on this
method of control, see Chapter 8, Telnet/Terminal Menus.
Telnet
You can connect to the ESU 120e via Telnet. Before attempting to
connect via Telnet, first define the IP address, the default gateway,
and the subnet mask using the front panel. When you begin the Tel-
net session, you will be prompted for a password. The default pass-
word is ADTRAN. You can change this password using the
Management submenu. The Telnet session will time out after a pre-
defined value that is also set in the Management menu.
Only one Telnet session can be active at one time.
3-10
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Menu
Chapter 4
The Status menu branch provides the ability to view the status of
the ESU 120e operation. See Figure 4-1.
1) NI PER F R PTS
2) NI ER R O R S
1)STA TUS
3) ACTIVE ALARMS
4)VIEW HISTO R Y
1) DTE DA TA /CK
2) DTE STA TUS
3) PO RT RATE
5) PO R T STA TUS
6) REMO TE PO RT
7) CLEA R PO RT A LM
8) ENET STA TUS
0.1 Nx56/64
0.2 DR O P MENU ITEMS
Figure 4-1. Status Menu Tree
61200420L1-1
ESU 120e User Manual
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
Menu flow is normally depicted from left to right. Arrows on the
lower right of the screen indicate the direction of scrolling to use to
view additional menu items. At every level of the menu, pressing
Cancel returns the system to the previous menu level. Pressing
Cancel repeatedly returns the system to the Main Menu.
Network Interface Performance Reports (NI PERF RPTS)
The Network Interface Performance Reports display the user’s
copy of the performance data. The ESU 120e maintains this perfor-
mance data on the network based on G.821. The data displayed is
data accumulated over the last 15 minutes and over the last 24
hours.
Use the scroll keys to access the complete display of the following
report fields:
15 Minutes
24 Hours
Data Values
%AS
BES
%EF
DM
Percentage of available seconds
Between 2 and 832 errors/sec
Percentage of error free seconds
Number of minutes with bit error rate of 1 x
-6
10 or greater
ES
Number of errored seconds (1 or more errors/
second)
SES
Number of severely errored seconds (more
than 832 CRC errors/sec). Approximate
-3
equivalent to a bit error rate of 1 x 10
UAS
Number of unavailable seconds (10 or more
consecutive seconds)
Figure 4-2. Network Interface Performance Report
4-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
If insufficient time has passed to collect data, NA displays. Con-
tinue with standard operating procedures to exit the display.
When this menu is active, performance data can be cleared by
pressing Clear (Shift 9) on the keypad. Only the user’s copy of the
performance data is cleared.
Since only the user’s copy of performance data is cleared by the
ESU 120e, the data displayed here might be different from the data
sent to the network as PRM data.
Network Interface Errors (NI ERRORS)
The NI Errors submenu displays the types of errors the Network
Interface (NI) detects. A blinking CSU error LED indicates that net-
work errors are detected.
The asterisk (*) above an item indicates the type of errors detected.
The error types are the following:
CRC CRC-4 bit errors. This is valid only if CRC-4 mode is
enabled.
BPV Bipolar violations.
XS0
FER
Excess zeros.
Framing errors.
Active Alarms
This menu item displays a list of current alarms reported by either
the base controller or any of the ports. If no alarms are current,
using this menu item displays End of List.
This display includes two lines of text. The top line is the alarm
source. The bottom line is the alarm message. A list of alarm mes-
sages is found in the appendix, ESU 120e System Messages.
61200420L1-1
ESU 120e User Manual
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
In addition to normal menu operation, you can also access this
menu item with the Alarm function (Shift 8) on the keypad. If one
or more of the Alarm LEDs are illuminated, an alarm is present.
Pressing Cancel returns to the previous menu item.
Alarm Source
Alarm Message
Figure 4-3. D isplay of Alarm Messages
View History
This menu item both displays and clears the accumulated status
changes of the unit.
View History displays a history of the first 20 status changes in the
unit, including the date, time, and type of change. The unit also
records for viewing, the date and time an alarm became active or
inactive, as well as the date and time of test activation or deactiva-
tion.
To clear the View History display, press Clear (Shift 9) with the
View History menu active.
4-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
Port Status
Port Status displays the signals monitored on the data ports. For
example, the Nx56/64 interface monitors the RTS, CTS, RD, and
RD, along with other signal lines. When a port is selected, the LCD
indicates if the signal is present.
The base Nx interface offers the status screen listed in this section.
When using other option cards, refer to the appropriate User’s
Manual for a definition of any status screens offered.
The Port Status of Nx56/64 is examined as an example of how to
use this item.
0.1 Nx56/ 64 Menu Items
DTE Data/CK
An asterisk (*) indicates an active status of the following lines.
TXD
RXD
ETC
LCK
Transmit data from the DTE
Receive data toward the DTE
External Transmit Clock from DTE
Lock Status of the phase locked loop
DTE Status
An asterisk (*) indicates an active status of the following lines:
RTS
CTS
DCD
DSR
Request to send from DTE
Clear to send to DTE
Data carrier detect to DTE
Data set ready to DTE
Port Rate
The Port Rate displays the current setting of the Nx port. Continue
with standard operating procedures to exit the display.
61200420L1-1
ESU 120e User Manual
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
0.2 D rop Menu Items (D SX Errors)
CRC
An asterisk displays under the CRC if there are CRC
errors in extended superframe format (ESF) mode. If
CRC-4 is not enabled on the Drop Port, the LCD
displays n/a.
BPV
SLIP
An asterisk displays under the BPV if the Drop Port
detects bipolar violations.
An asterisk displays under the SLIP if the drop plug-
on board detects frame slips. This is caused by
multiple clock sources in the application.
FER
An asterisk displays under the FER if the Drop Port
detects frame bit synchronization errors.
Remote Port
Remote Port displays the status of activity on the Control In remote
port. This is useful for troubleshooting communication sessions,
and for verifying cabling.
RX Characters received at remote port
ID
Unit ID received at remote port
CR Correct CRC received
C
PC Correct passcode received
TX Characters transmitted from the remote port
Clear Port Alarm
Clears the Link Failed alarms on option modules that have been
removed from the ESU 120e chassis.
ENET Status
TX
Indicates that data is being transmitted from the 10BaseT
port
RX Indicates that data is being received by the 10BaseT port.
LN Indicates the current status of the 10BaseT link integrity test
K
(this should always be on when the unit is connected to a
functional 10BaseT hub.
CPU Active when the CPE is accessing the 10BaseT interface.
4-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Menu
Chapter 5
The Configuration menu sets the ESU 120e operational configura-
tion, including all network interface parameters, the allocation of
the DS0s, and the port parameters. See Figure 5-1 on page 5-2.
Menu flow is normally depicted from left to right. Arrows on the
lower right of the screen indicate the direction of scrolling to use to
view additional menu items. At every level of the menu, pressing
Cancel returns the system to the previous menu level. Pressing
Cancel repeatedly returns the system to the Main menu.
61200420L1-1
ESU 120e User Manual
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
1) INTFACE
1) CTL PORT
2) NFAS WORD
3) CAS/TS16
4) CRC-4
2) TRAPS
3) ACCESS
4) INIT MODEM
5) EXIT TERM MODE
6) IP INTERFACE
7) IP ADDRESS
8)SUBNET MASK
9)DEFAULT ROUTER
10) SLIP RATE
5) RFA GEN
1) NETWORK (NI)
6) TIMING MODE
2) UNIT
A) SLIP FLOW CTL
B) PROXY TRAPS
3) MAP XCHNG
4) MAP IN USE: A(B)
OFF
ON
1) MAP A @:HH:MM
2) MAP B @:HH:MM
3) CONFIG 5)TS0 MAP A
1) COPY A > TEMP
2) CREATE TEMP
3) REVIEW MAP A
4) REVIEW TEMP
5) EDIT TEMP
1) INTERFACE
2) DSO RATE
3) TX CLK CNTRL
4) DATA
1) COPY B > TEMP
2) CREATE TEMP
3) REVIEW MAP B
4) REVIEW TEMP
5) EDIT TEMP
6) TS0 MAP B
5) CTS
6) APPLY TEMP > A
6) DCD
7) DSR
6) APPLY TEMP > B
8) “0” INHIBIIT
9) INBAND
A) TX CLK SOURCE
0.1 NX56/64
0.2 DROP PT
7) PORT CONFIG
1) NFAS WORD
2) CAS/TS16
3) CRC-4
Figure 5-1. Configuration Menu Tree
5-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
NETWORK (NI)
This menu item accesses the configuration of parameters associated
with the network interface in the base unit. There are eight sub-
menu items that include setting the format, the line build out
(LBO), and the timing mode.
Network (NI) Menu Items
The menu items are:
Menu Item
Interface
(INTFACE) interface.
Description
Selects either the 120Ω DB15 interface or the 75Ω BNC
Choices: 120Ω, 75Ω. BAL and 75Ω UNBAL
In 75Ω UNBAL mode, both the Tx and Rx are shield
grounded.
Framing
NFAS Word. If enabled, the network interface receiver
requires the NFAS word (TS0 in odd frames) and the FAS
word (TS0 in even frames) for frame sync. When disabled,
only the FAS word is needed for frame sync.
Choices: Enable, Disable
CAS/TS16
Enables/Disables Channel Associated signalling (time slot
16 multiframing). When this menu option is enabled, the
following occurs:
1. The TS16 multiframe alignment signal is inserted in the
outgoing data stream.
2. Signaling Bits are transmitted in TS 16 for all TS0s that are
mapped to a signalling-capable port (Base Drop port, for
example). In TS0s that are mapped to “Idle” or data ports,
“1s” are transmitted in the signalling bit positions.
3. The TS16 multiframe alignment signal must be received
for frame sync.
61200420L1-1
ESU 120e User Manual
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
• Note that if CAS/TS16 is enabled, TS16 may not be
mapped to a port, and will be forced to “Idle”. When
CAS/TS16 is disabled, and TS16 is mapped to a port, the
data in TS 16 will be mapped through from the network
to the mapped port. For common channel signalling ap-
plications, CAS/TS16 should be disabled and TS16
mapped to the drop port. TS16 may also be mapped to
the base Nx56/64 or an option module data port.
• When CAS/TS16 is enabled, TS16 is forced to idle in DS0
Map A and B and may not be mapped. This configura-
tion must be used if there are multiple signalling-capable
ports that are mapped to the Network Interface. For ap-
plications where the Base Drop Port requires channel as-
sociated signalling, (connection to a PBX, for example)
CAS/TS16 must be enabled and TS16 left idle in the DS0
Map.
CRC-4
When this option is enabled, the CRC-4 checksum bits are
transmitted in the outgoing E1 data stream. Also, the
received signal is checked for errors.
Choices: Enable, Disable
RFA Gen
When enabled, remote frame alarm is transmitted toward
the Network during alarms.
Choices: Enable, Disable
Timing
Mode
Selects the clock source for transmission toward the network
from the NI. See ESU 120 Clock Sources on page 5-5 for more
information.
5-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
ESU 120e CLOCK SOURCES
The ESU 120e is operable from various clock sources permitting it
to perform properly in many different applications. Set the net-
work interface clocking options with the clocking options set by the
Network (NI) Configuration menu options.
The following clock source options are available:
•
•
•
•
•
Network Timed
Base Drop Timed
Base DTE Timed
Internal Timing
Normal (CSU) (only when secondary interface module is in-
stalled)
The selected clock option always designates the clock source for
transmission. Clocking necessary for receiving data is always re-
covered from incoming data.
61200420L1-1
ESU 120e User Manual
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Network Timed
The network is the source of timing. The received data clocking is
looped back to the network where it is used to determine the trans-
mission timing. This option is also referred to as loop timed as the
transmission clock is derived from the received clock. See Figure 5-
2.
OSC
E1 XMIT
Network
Interface
Secondary
Interface
(OPTION)
E1 Receive
Drop Port
Nx56/64
DTE CLOCK
PBX
DTE
Figure 5-2. Network Timed Clock Source
5-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Base D rop Timed
The PBX is the source of timing. The ESU 120e uses the clock
derived by the Base Drop interface for transmission timing (see Fig-
ure 5-3).
OSC
E1 XMIT
Network
Interface
(OPTION)
E1 Receive
Drop Port
Nx56/64
DTE CLOCK
PBX
DTE
Figure 5-3. D rop Timed Clock Source
61200420L1-1
ESU 120e User Manual
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Base D TE Timed
The DTE is the source of timing. The ESU 120e uses the incoming
DTE clock to determine the transmission timing. This is typically
used in applications where it is necessary to have the DTE as the
primary clock source, (such as limited distance line drivers). See
Figure 5-4.
OSC
E1 XMIT
Network
Interface
(OPTION)
E1 Receive
Drop Port
Nx56/64
DTE CLOCK
PBX
DTE
Figure 5-4. Network Timed Clock Source
5-8
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Internal Timing
The ESU 120e is the source of timing. The ESU 120e is configured
to use its own internal oscillator as the source of timing. Applica-
tions include private line driver circuits where one end is set to net-
work and the other to internal. See Figure 5-5.
OSC
E1 XMIT
Network
Interface
(OPTION)
E1 Receive
Drop Port
Nx56/64
DTE CLOCK
PBX
DTE
Figure 5-5. Internal Clock Source
61200420L1-1
ESU 120e User Manual
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Normal (CSU) Timing
The typical timing option arrangement is shown in Figure 5-6. The
PBX is looped timed sending data to the ESU 120e which is actually
synchronous to the received data. The Network Interface (NI) is
the actual source of all timings. This timing option is the same as
that typically used for CSUs. This is the preferred mode for use
with a PBX application.
This timing mode works equally well when the PBX is the source of
timing. In that configuration the network would not be providing
timing.
OSC
E1 XMIT
Secondary
Network
Interface
(NI)
Interface
(SI)
(OPTION)
(IO PB)
E1 Receive
PBX
Drop Port
Nx56/64
DTE CLOCK
PBX
DTE
Figure 5-6. Normal (CSU)
The network interface and secondary interface clocking options
are set by using the Network (NI) Configuration menu options.
5-10
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Unit Menu
The Unit menu changes the baud rate of the Control In port and the
setup of the Dial Out port. The menu items are:
Menu Item
Description
Ctl Port
Sets the baud rate for communication with the PC or
modem.
Choices: 1200, 2400, 9200, 9600, and 38400 kbps
Traps
Enables or disables the transmission of trap
messages.
Choices: Enable and Disable
Access
Sets the method of connection from the ESU 120e to
T-Watch/SNMP.
Choices:
Direct - Used if connected directly to the PC.
Dial - Used when connection is through a modem.
The dial string is entered from T-Watch/SNMP.
Init Modem
Allows you to choose an industry standard or a
custom initialization string for a modem connected
to the control port.
Choices: Industry standard and Custom
Initialization String
Exit Term Mode Takes the unit out of terminal mode.
IP Interface
Selects the TCP/IP physical interface; 10-Base-T
Ethernet or SLIP using the EIA-232 serial port.
Choices: 10-Base-T Ethernet or SLIP
If this option is set to SLIP, the EIA-232 port
may not be used as a terminal interface.
IP Address
This is the IP address that uniquely identifies the
ESU 120e on a TCP/IP network. This address is
composed of four decimal numbers, each in the
range of 0 to 255, separated by periods. This value is
used for either the 10BaseT Ethernet or SLIP
interface, depending on the IP interface setting
61200420L1-1
ESU 120e User Manual
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
Subnet Mask
This defines which part of a destination IP address is
the Network number. It is used along with the ESU
120e IP address to determine which nodes must be
reached through the default IP Gateway. This value
is set to 0.0.0.0 when the IP interface option is set to
SLIP.
Default Router All IP Packets destined for nodes not on the ESU
120e unit’s local network are not forwarded through
this IP address. Normally, this address defines a
router connected to the ESU 120e unit’s local
network. This value is ignored when the IP interface
is set to SLIP.
SLIP Rate
This sets the baud rate for the Chain-In port when
used as the SLIP connection for SNMP management.
Choices: 1200, 2400, 9600, 19200, 38400
SLIP Flow CTL This is used to activate flow control on the Chain-In
port when used as the SLIP interface. Hardware
mode uses RTS and CTS.
Choices: None, Hardware
Proxy Traps
This determines which interface is used for
forwarding traps from units being “proxied” for.
Choices: 10 BaseT, Chain-In
5-12
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Map Exchange (Map Xchng)
The Map Exchange menu enables and sets the automatic time of
day map switch. The unit provides selection of the hour, minute,
and seconds for the map switching to take place. The menu items
are:
Menu Item
Description
OFF
ON
Indicates the map in use does not change (disabled).
Indicates that the map in use will change at a user-
selected time of day (enabled).
Scroll to select Auto to enable or Off to disable the
Automatic Map Change feature and press Enter to
activate the selection.
When Auto is selected, the unit displays the screens
to set times for switching. After editing Map A,
press Enter to record the Map A settings and activate
the selection fields for Map B. Use the same
operation to edit switching time for Map B.
Map In Use: A(B)
This menu item controls the TS0 map the ESU 120e uses and dis-
plays the map in current use.
61200420L1-1
ESU 120e User Manual
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
TS0 Map A and TS0 Map B
The TS0 maps designate which TS0s are assigned to which port.
There are three maps, TS0 Map A, TS0 Map B, and the Temporary
(Temp) map. See Figure 5-7.
T E M P
T S 0 A
T S 0 B
Figure 5-7. D S0 Map D esignations
TS0 A and TS0 B are the current maps the ESU 120e uses. The Temp
map generates a map before putting it into use.
You can copy TS0 A to TS0 B by copying the TS0 A map into the
TEMP map. Then apply (write) the TEMP map into TS0 B.
5-14
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
The menu items are:
Menu Item
Description
COPY A >TEMP This copies the current map (A or B) into a TEMP map
area. This permits modification without disturbing
the existing map. When the modifications are
completed, the TEMP map is written to current MAP
A (B) by selecting Apply.
CREATE TEMP
This creates a map by defining a port or Idle for all
TS0s. When CREATE TEMP is first selected, all TS0s
are set to Idle.
PORT: IDLE, TST, + option module ports
TST designates which TS0s are used for QRSS testing
when activated under the 4)TEST Menu. When not
used for testing, the TST designation is identical to
IDLE.
With the cursor on CREATE TEMP, press Enter. The
unit displays the selection screen with the cursor
positioned on the first selection TS0 number. See
Figure 5-8.
Select DS0 Number
Select Port
Figure 5-8. Create Temp Selection Screen
Use either the scroll method or numbers to enter the
TS0 number (do not mix the use of the keys). Pressing
Enter completes the selection and moves the cursor to
PORT, the next field.
61200420L1-1
ESU 120e User Manual
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
Scroll to select the port which is dependent on the
installed option card. Press Enter to complete the
selection and move the cursor back to the TS0
field.With the cursor on the TS0 field, the TS0 number
can be incremented or decremented by scrolling. If
Copy is pressed, the contents of the last TS0 entered
are placed in the new TS0 number.When all entries
are complete, Cancel moves the cursor to the last of
the submenu choices, 6)APPLY. Either apply the
newly created TS0 map or press Cancel to return to
the TS0 Map A (B) submenu choices.
Selecting Apply will not disrupt the operation of
unmodified ports
REVIEW MAP
A(B)
Permits a quick review of the number of TS0s
assigned to each port and the number of unassigned
TS0s (Idle or TST) as defined in the currently applied
Map A(B).
REVIEW TEMP
EDIT TEMP
This menu item is operated the same for the TEMP
map as is 3)REVIEW MAP A or Map B.
The map in the TEMP file can be edited to whatever
configuration is desired. If Map A had been copied
into the TEMP file, then after editing, the TEMP file
could be applied to MAP A or MAP B. The menu
operation is identical to 2) CREATE TEMP with the
exception that the existing port selections display.
APPLY TEMP > A Writes the TEMP map into Map A. Apply is usually
the last step in updating a map and is accessed
automatically at the end of editing or creating a
temporary map. Currently, it can be bypassed by
selecting another menu choice.
5-16
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Port Configuration (Port Config)
Port Configuration selects and configures the parameters associ-
ated with any data port in the unit. For example, parameters for
the Drop Port Interface (PBX) interface are set through this menu.
The items that can be set depend on which option module is
installed. The list of option ports will vary with the configuration.
The ESU 120e is designed so that any additional ports developed in
the future will contain the appropriate menu selections to provide
access by use of this menu item.
The Config menus for options ports are described in separate sec-
tions of the manual supplied with the option card.
0.1 Nx56/ 64 Port Configuration (Port Config) Menu Items
The menu items are:
Menu Item
Description
INTERFACE This option sets the electrical interface for the Base
Nx56/64 port.
Choices: V.35, V.11 (X.21), RS530, V.36
TSO RATE
This sets the base rate of the interface. The actual
data rate depends on the number of DS0s assigned
to the Nx port.
Choices: 56K or 64K
TX CLK
CNTRL
Controls the clock used by the TSU 120e to accept
transmit (TX) data from the DTE. The default is
normal. If the interface cable is long, causing a
phase shift in the data, the clock can be selected as
Invert. This switches the phase of the clock which
should compensate for a long cable.
Choices: Normal, Invert
61200420L1-1
ESU 120e User Manual
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
DATA
Used to control the inverting of the DTE data. This
inversion can be useful when operating with an
HDLC protocol. Often used as a means to ensure
1s density.
Choices: Normal or Invert
If Invert is selected, zero (0) inhibit should also
be selected to prevent an open DTE input from
placing zeros on the network.
CTS
Used to control characteristics of CTS.
Choices: Normal, (see Table 3-A) or Force On
DCD
Data Carrier Detect. Indicates to the DTE when a
valid signal is being received at the Network
Interface.
Choices: Normal (see Table 3-A) or Force On
DSR
Data Set Ready. This signal indicates to the DTE
when the DCE is turned on and ready for
operations.
Choices: Normal (see Table 3-A) or Force On
0 INHIB
The Nx interface will detect an uninterrupted
string of zeros (0s) being transmitted toward the
network. If 0s are transmitted for >1 second, the
TSU 120 will force 1s.
Choices: On or Off
INBAND
The Nx56/64 port is capable of providing an
inband communications channel (for T-Watch and
SNMP) between units. This is accomplished by
using 8 kbps of the first DS0 assigned to that
particular Nx56/64 port. If in 56 K mode, no data
bandwidth will be used. Inband must also be
enabled at the destination port.
Choices: On or Off, On Demand
TX CLK
SOURCE
This controls the source of the clock used by the
TSU 120e to accept transmit data from the DTE.
The default is Internal. If the application requires
that the DTE device provides the clock with the
transmit data, the External setting is used.
Choices: Internal, External
5-18
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Table 5-1. Normal Mode of Operation
RTS
Signal V.54 Loop- 511 TST
back ON
Follows OFF OFF
Self Test NetwkTest
Active Active
OFF OFF
No DS0
Mapped
Network
Alarm
CTS
OFF
OFF
DCD
DSR
—
—
—
—
OFF
OFF
—
OFF
OFF
OFF
—
OFF
OFF
OFF
Where “—” = don’t care
*Until backup becomes active
0.2 D rop Port Configuration (Port Config) Menu Items
The menu items are:
Menu Item
Description
NFAS Word NFAS Word. If enabled, the network interface receiver
requires the NFAS word (TS0) in odd frames) and the
FAS word (TS0 in even frames) for frame sync. When
disabled, only the FAS word is needed for frame sync.
Choices: Enable, Disable
CAS/TS16 Enables/Disables Channel Associated signalling time
slot 16 multiframing). When this menu option is
enabled, the following occurs:
1. The TS16 multiframe alignment signal is inserted in
the outgoing data stream (toward the PBX).
2. Signaling Bits are transmitted in TS 16.
3. The TS16 multiframe alignment signal must be
received for frame sync.
If CAS/TS16 is enabled on the Drop Port, it must
also be enabled on the Network Interface.
CRC-4
When this option is enabled, the CRC-4 checksum bits
are transmitted in the outgoing data stream toward PBX.
Also, the received signal is checked for errors.
Choices: Enable, Disable
61200420L1-1
ESU 120e User Manual
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
5-20
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Menu
Chapter 6
The utility menu tree displays and sets system parameters (see Fig-
ure 6-1). This includes setting the time and date, resetting all
parameters to factory values, or re-initiating the unit. This menu
also displays the unit software revision and the unit ID setting.
TIME: HH:MM:SS
1) TIME/DA TE
DA TE: MM/DD/YY
(R eturns all configurations
to factory settings)
2) FA CTO R Y R ESTO R E
3) SET PA SSCO DE
4) UNIT ID
3) UTIL
5) SO FTWARE REV
(Displays Current
Software R evision
6) PO R T UTILITY
7) ENET A DDR ESS
8) CMD MO DE
Figure 6-1. Utility Menu Tree
61200420L1-1
ESU 120e User Manual
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
Menu flow is normally depicted from left to right. Arrows on the
lower right of the screen indicate the scrolling direction to view
additional menu items. At every level of the menu, press Cancel to
return the system to the previous menu level. Pressing Cancel
repeatedly returns the system to the Main menu.
Time/ D ate
This menu option displays or edits the current time and date. The
ESU 120e maintains the time and date during power-off conditions.
Pressing Enter after any numeric change always records the entry
and moves to the next editing position. You can also move to a dif-
ferent field to edit by pressing Enter at the editing position without
making any change, or by using the Up and Down Arrow keys.
Pressing Cancel at any time ends the editing process.
Factory Restore
This menu item restores the factory default settings for all unit
parameters, including configured TS0 maps.
Set Passcode
Enter Passcode from Other Menus
The Passcode prompt may make an unexpected appearance from
other menu operations. This happens only when the unit is operat-
ing in the limited access mode, i.e., without an active passcode. The
limited access mode may become active even if a passcode was
entered as it does when there is no activity for ten minutes. If the
unit is to be remotely accessed using T-Watch PRO, a passcode
must be entered. When managing a number of units, the passcode
can be the same for all.
The unexpected appearance of the Passcode prompt occurs, for
example, while operating in a limited access mode and attempting
to change the Data Rate, (2)CONFIG, 2)UNIT, 1)CNTROL PORT,
1)DATA RATE. Use the number keys to enter the correct passcode
and press Enter. The unit displays Access Granted.
6-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
Pressing any key after entering a passcode causes the unit to return
to the previous active menu. In this case it returns to 2)CONFIG,
2)UNIT, 1)CNTRL PORT, 1)DATA RATE to permit changing the
data rate.
Change/ Set a Passcode
The passcode can be changed or set at any time or eliminated alto-
gether through the Utility menu item 3)SET PASSCODE. This pro-
cedure requires the current passcode (if one is established) for
operation.
The passcode can only be entered by using numbers. After enter-
ing the desired passcode, press Enter.
Set a null passcode at the 3)SET PASSCODE menu by pressing
Enter without any numbers. This sets a null passcode and grants
unlimited access.
Special Feature
For added security protection the unit is equipped with an auto-
matic time-out for operation with the password. After ten minutes
of inactivity, the unit reverts to limited access operation. To make
changes in the configuration, the passcode can be reentered. If the
passcode number is lost, contact ADTRAN Customer Service for
assistance.
No Passcode D esired
At the New Passcode prompt (in the Set Passcode menu), press
Enter without any numerical entry. The system nullifies the need
to enter a password for subsequent use and proceeds to the Unit ID
prompt.
61200420L1-1
ESU 120e User Manual
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
Unit ID
This menu is used to access the current Unit ID setting. Viewing is
available in limited access mode. Editing or changing the Unit ID
requires the use of a password as in editing mode. Unit Identifica-
tion numbers must be between 2 and 250. If an out-of-range num-
ber is entered, the unit assumes the upper limit number of 250.
To Set the Unit Identification
In the Unit ID menu (item 4) under the UTIL menu, enter any value
between 2 and 250. The number 1 is reserved for the PC.
Pressing Enter records the Unit ID number and establishes its avail-
ability for operation by remote control. The unit proceeds to the Set
Control Port prompt.
No Unit ID D esired
Without entering any numbers at the Unit ID prompt, press Enter.
Pressing Enter with no Unit ID recorded establishes the unit as not
able to be operated by remote control.
Software Revision (Software Rev)
This menu provides access to the display of the current software
revision level loaded into the base unit controller. This information
is required when requesting assistance from ADTRAN Customer
Service or when updates are needed.
Use Cancel to exit.
6-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
Port Utility
This menu provides access to the display of the current software
information for each port installed in the unit. This information is
required when requesting assistance from ADTRAN customer ser-
vice or when updates are needed.
Enet Address
Displays the Ethernet address for the 10BaseT port.
CMD Mode
Reserved for factory use.
61200420L1-1
ESU 120e User Manual
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
6-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Test Menu
Chapter 7
The Test menu initiates different types of unit tests and displays
test results in the LCD window. The Test menu contains four items.
See Figure 7-1.
Executing tests will disrupt some of the normal operation. See
individual menu items concerning tests before executing.
LINE ON
FE1 LOOPBACK
1) LOCAL LOOPBCK
2) TEST PATTERN
PAYLOAD ON
NO LOOPBACK
1) NETWORK TESTS
ALL ZEROS
QRSS ALL TS0S
QRSS TST TS0S
ALL ONES
5)TEST
NONE
3) PATTERN RESULT
(Displays results)
2) RUN SELF-TEST
3) PORT TEST
1) LOOPBCK
2) 511 PATT
0.1 NX56/64
0.2 DROP
3) DISP 511 RESLT
LOOPBACK
4) CANCEL TESTS
(OPTION PORTS)
Figure 7-1. Test Menu Tree
61200420L1-1
ESU 120e User Manual
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
Menu flow is normally depicted from left to right. Arrows on the
lower right of the screen indicate the scrolling direction to view
additional menu items. At each level of the menu, pressing Cancel
returns the system to the previous menu level. Pressing Cancel
repeatedly returns the system to the Main menu.
Network Tests
Network tests control the activation of loopbacks and the initiation
of data test patterns.
Network tests are run on the Network Interface (NI). You can select
three different test configurations to determine the type of loopback
and the pattern to run. Test results display in the LCD window.
Executing Network Tests will disrupt normal data flow unless only
TST TS0s are selected for testing.
Loopback Tests
A number of different loopbacks can be invoked locally from the
front panel, by T-Watch commands, or remotely by using special in-
band codes (AT&T D4 network loop-up and loop-down codes).
Additionally, the loopbacks can be remotely controlled by means of
out-of-band commands by the E1 ESF FDL or from T-Watch PRO
via a modem connection.
Network Interface Loopbacks
Network interface loopbacks (see Figure 7-2 on page 7-3) affect the
entire E1 data stream. There are two types of network loopbacks,
line loopback and payload loopback.
Line loopback loops all of the received data back toward the net-
work. The transmitted data is the identical line code that was
received, including any bipolar violations or framing errors.
Payload loopback is similar to line loopback, except that the fram-
ing is extracted from the received data and then regenerated for the
transmitted data.
7-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
ESU 120e
NI CSU
Secondary
Interface
E1
Payload Loopback
Line Loopback
Figure 7-2. Network Loopback Tests
LOCAL LOOPBCK
There are three available choices for setting the local loopback:
Line On
Activates the line loopback
Payload On
Activates the payload loopback
No Loopback Deactivates the loopback
Scroll to select a setting and record it by pressing Enter. The unit
returns the display of 1)LOCAL LOOPBCK and 2)REMOTE LOOP-
BCK
REMOTE LOOPBCK
FE1 Loopback sends V.54 loopback code in all mapped TSOs
toward the network. Far end will respond by initiating a local line
loopback.
TEST PATTERN
All Ones
Sends an all ones pattern to the network.
All Zeros
Sends an all zeros pattern to the network.
61200420L1-1
ESU 120e User Manual
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
QRSS Pattern
The QRSS pattern is commonly used to simulate real data in E1
interfaces. This pattern can be assigned to appear in all TS0s or
only in TST TS0s. When QRSS is set in all TS0s and one of the net-
work loopbacks previously described is activated at the far end, a
total end-to-end integrity check can be run without the need for
any external test equipment. When QRSS is assigned to TST TS0s,
an integrity check of the link can be run along with normal data
flow. The TST TS0s are user assigned as part of the TS0 Map.
This sets the pattern for the test and initiates the transmission of the
pattern. The test is terminated by selecting None. The following
patterns are available:
QRSS All TS0s
Generates a QRSS test pattern and inserts the
pattern into all TS0s
QRSS TST TS0s Inserts a QRSS pattern in those TS0s mapped as
TST in the currently active map (A or B)
None
Terminates pattern generation
QRSS always runs at 64K/TS0.
For example, use the up and down arrows to select QRSS ALL
TS0s. Press Enter to record the selection. The ESU 120e starts to
generate a QRSS test pattern and inserts the pattern into all TS0s.
To end the test, select None.
7-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
PATTERN RESULT
Displays the results of the test currently active. Leaving and
returning to this menu item does not interrupt the test.
Pressing 2 injects errors into the test pattern. These errors are
detected by the device performing the pattern check.
ES
The number of seconds with at least 1 bit error.
BES
The number of seconds with more than 1 bit error and
less than 320.
SES
The number of seconds with more than 320 bit errors.
*SYNC Indicates if pattern sync is (yes) or is not (no) valid. The
asterisk (*) indicates if pattern sync has been lost since
the start of testing.
Clear results by pressing shift 9. The results are accumulated until
the test pattern is set to None or Cleared.
Using TST TS0s for testing can be very useful, particularly in Frac-
tional E1 applications. You can run an end-to-end test on the Frac-
tional TS0s by 1) setting for Map B the TST in the same TS0 as used
by Map A to receive data from an Nx56/64 port and 2) by looping
the far end using a V.54 loopback code on the Nx56/64 port. In
addition, a single TS0 can be used for continuous testing while
other TS0s are passing normal data. This will also provide an end
to end check on the entire link. Set each end to send QRSS in TST
TS0s (using 1 TS0) and occasionally view the results on the Pattern
Result menu selection.
61200420L1-1
ESU 120e User Manual
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
Run Self-Test
The self-test checks the integrity of the internal operation of the
electronic components by performing memory tests and by sending
and verifying data test patterns through all internal interfaces.
Although actual user data cannot be passed during these tests, the
self- test can be run with the network and DTE interfaces in place
and will not disturb any external interface.
The memory portion of the self-test automatically executes upon
power-up. A full self-test can be commanded from a front panel
menu or from T-Watch PRO.
In addition to the specified self-tests, background tests are also run
on various parts of the internal electronics. These run during nor-
mal operation to confirm continued correct functioning.
This menu selection is used to execute a full internal self-test. The
results of the self-tests are displayed in the LCD. Upon invoking
the command, the LCD displays System Self-Test and the Test LEDs
are illuminated. Test failures are displayed in the LCD window.
7-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
The self-test consists of the following tests:
Test Name What it does . . .
Board level tests Each of the ESU 120e boards contains an on-
board processor which executes the following
series of tests checking the circuitry on the board:
• RAM tests; EPROM checksum
• TS0 map tests
• On board data path (sending a known test pat-
tern through an on-board loop)
Unit level tests
• Front panel LED verification
• Phase-Lock Loop verify
• Board-to-board interface test
A test pattern is sent from the controller through
a loopback on all other boards and is checked on
the controller. This verifies the data path, clocks,
and control signals.
If a failure is detected, note the failure number
prior to contacting ADTRAN Technical Support.
The execution of self-test will disrupt normal
data flow and prevent remote communication
until the self-test is completed.
Port Tests
The Port Tests menu is used to activate testing of specific data
ports. It controls the activation of loopbacks and the initiation of
data test patterns. Test results are displayed in the LCD window.
The execution of Port Tests will disrupt normal data flow in the
port being tested.
61200420L1-1
ESU 120e User Manual
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
Port Test Menu Items for 0.1 Nx56/ 64
0.1 Nx56/64 is the base Nx interface. It offers the following test
functions:
LOOPBK
This initiates a loopback. The following options are available:
PRT/LCL The Nx port activates both a Local loopback (back
toward the DTE) and a Port loopback when either is
invoked.
REMOTE The remote loopback causes a V.54 code to be sent to
the far end. The Nx at the far end activates a PRT/LCL
loopback upon detection of the V.54 code.
OFF
The loop is deactivated.
The ESU 120e checks the remote loopback activation by detecting
a proper response from the remote end. While waiting for the re-
sponse, the display shows Looping. If successful, the display
changes to Looped -Up. If unsuccessful, the display shows Failed.
511 PATT
Activates the generation of the 511 test pattern.
ON
The pattern check circuitry is enabled and a test started.
The test is ended by selecting OFF.
OFF
The pattern generation and check is disabled.
D IS 511 RESLT
Displays the results of the 511 test indicated in the 511 option. The
results are in the form of the number of errored seconds. The error
count can be cleared by pressing the Clear key (shift+9).
7-8
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
Port Test Menu Items for 0.2 D rop
Loopback
Loopback activates the loopback function on the base Drop inter-
face. The available loopbacks are a Port Loopback (towards the NI)
and a Line Loopback (towards the PBX or other terminal equip-
ment).
Cancel Tests
Use this menu selection to deactivate all active tests, including tests
on option modules.
61200420L1-1
ESU 120e User Manual
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
7-10
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Telnet/Terminal Menus
Chapter 8
MAIN MENU
The Telnet/Terminal Main menu is the first menu displayed after
the telnet/terminal session is established (see Figure 8-1). The
default telnet/terminal password is ADTRAN.
Only one telnet/terminal session may be active at a time.
ADTRAN - ESU 120e
Password: XXXXXXXX
Main Menu
1) Status
2) Config
3) Util
4) Test
5) Management Config
6) Flash Download
7) Quit Session
Figure 8-1. Telnet/ Terminal Main Menu
61200420L1-1
ESU 120e User Manual
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Status, Config, Util, and Test Menu Options
These menu items access the same modified menus that you can
access through the front panel. For detailed information on the
available menu options, see the following sections:
•
•
•
•
Status Menu in Chapter 4
Configuration Menu in Chapter 5
Utility Menu in Chapter 6
Test Menu in Chapter 7
TS0 Maps Configuration Menu
The Telnet/Terminal version of the TS0 maps configuration menu
takes advantage of the 24-line VT 100 display. Upon entering this
menu, the current Temp (temporary) map displays and is followed
by nine selections that you can use for configuring and reviewing
map information.
TEMP MAP
DS0
PORT
DS0
PORT
1
2
3
4
5
6
7
8
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
9
10
11
12
13
14
15
16
1) COPY MAP A TO TEMP MAP
2) COPY MAP B TO TEMP MAP
3) CREATE TEMP MAP
4) REVIEW MAP A
5) REVIEW MAP B
6) REVIEW TEMP MAP
7) EDIT TEMP MAP
8) APPLY TEMP MAP TO MAP A
9) APPLY TEMP MAP TO MAP B
Figure 8-2. TS0 Temp Map
8-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
You can use the Up and Down arrows or number keys to move the
cursor from one selection to another. Use the Enter key to perform
the action displayed in the LCD to the right of the cursor.
Normally, map configuration involves these steps. The first step is
optional and consists of initializing the Temp map to one of three
configurations (current Map A, current Map B, or all IDLES). Step 2
involves editing the Temp map so that it reflects the desired map
configuration. Finally, step 3 replaces the current TS0 map A or B
configuration with the Temp map configuration.
Initializing the Temp Map
Upon entering the TS0 maps configuration menu, the Temp map
reflects its last configured state. You can then use selections 1
through 3 to initialize the displayed Temp map to one of three con-
figurations. You can use selections 1 and 2 to initialize the Temp
map from its current configuration to one which reflects the cur-
rently stored Map A or B configurations, respectively. Selection 3
initializes the Temp map to an all IDLE state.
Editing the Temp Map
If further changes to the Temp map are needed, use selection 7 to
enter the Temp map edit mode. Upon entering this mode, the cur-
sor location moves to TS0 number one in the TS0 field of the Temp
map. The cursor may be moved from one TS0 to another using the
Up and Down arrows until it is located at the TS0 number whose
assigned port needs to be changed. At this point, pressing the Enter
key causes the cursor to move into the Port field. The Up and Down
arrows are then used to allow scrolling through the possible port
selections. To restore the previous port assignment and return to
the TS0 field, you may press the ESC key. Otherwise, press the
Enter key to save the current selected port and return to the TS0
field. Once the cursor is again located in the Temp map TS0 field,
pressing the ESC key a second time, causes the cursor to return to
selection 1 below the Temp map display.
Applying the Temp Map
Once the Temp map reflects the desired configuration, use selec-
tions 8 or 9 to apply this configuration to Map A or B, respectively.
Reviewing Temp Maps
Selections 4 through 6 give a summary of the number of ports
assigned to Map A, Map B, and the Temp map, respectively.
61200420L1-1
ESU 120e User Manual
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Remote Menu Access
Displays telnet menus for a remote device (may be another ESU/
TDU or any other ADTRAN product that supports telnet via its
EIA-232 chain port). After selecting this option, the user may
choose to connect to a device entered in the Unit Access Table or
enter a unit ID for a unit not in the Unit Access Table. CTRL + X
terminates the session and returns to the ESU 120e Main menu.
MANAGEMENT CONFIGURATION
This menu sets management information, such as SNMP commu-
nity names and trap destination addresses.
SNMP Read Community
SNMP Read Community Name defaults to public. NMSs using
this community name have Read access for all supported MIB
objects but do not have the ability to change MIB objects. This
value must be set to the same value on both the ESU 120e and the
NMS (OpenView®, etc.) in order for the NMS to have Read access
to MIBs supported by the ESU 120e. This value must be a text
string of 16 characters or less.
SNMP Read/ Write Community
SNMP NMS using this community name have full read/write
access to all supported MIB objects (defaults to private). This set-
ting must be the same value on both the ESU 120e and the NMS in
order for the NMS to have read/write access to MIBS supported by
the ESU 120e. This value must be a text string that is 16 characters
or less.
To access other units external to the ESU 120e (proxied units) us-
ing an SNMP MIB browser, append a period and the unit ID of
the external device to the Read Only and Read/Write community
name used in the MIB Browser, for example public.4. See the Ap-
pendix B, Understanding SNMP for more information.
8-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
SNMP Trap Community
This community name is used for all SNMP traps forwarded by the
ESU 120e. Traps received from daisy chained units have a period
and the unit ID appended to the trap community name.
Host 1 Trap IP Address
The first of four entries for SNMP trap destination addresses. The
ESU 120e forwards all SNMP traps to the IP address specified in
this entry. If the address is set to the default value of 0.0.0.0, no
traps are forwarded for this particular value.
Host 2 Trap IP Address
Defaults to 0.0.0.0. Second destination address for SNMP traps.
Host 3 Trap IP Address
Defaults to 0.0.0.0. Third destination address for SNMP traps.
Host 4 Trap IP Address
Defaults to 0.0.0.0. Fourth destination address for SNMP traps.
System Name
A text string that can uniquely identify an SNMP managed node.
System Contact
A text string containing the name, phone number, etc. of the indi-
vidual responsible for maintaining an SNMP managed node.
System Location
A text string describing the physical location of an SNMP managed
node (for example, SECOND FLOOR PBX ROOM).
61200420L1-1
ESU 120e User Manual
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Auth. Fail Traps Sent
(DISABLED, ENABLED: defaults to DISABLED)
When enabled, the ESU 120e issues an SNMP trap when any SNMP
request is received with an invalid community name. Can be used
for security purposes.
Poll Link Status Traps Sent
(DISABLED, ENABLED, defaults to DISABLED)
When enabled, the ESU 120e sends an SNMP trap whenever a
device configured to be polled fails to respond. When the device
begins responding to polls, a poll link-up trap is sent. The format of
the traps are defined in the agent MIB.
Ping IP Host
Allows the user to Ping a specific IP address.
Telnet/ Terminal Timeout
The ESU 120e terminates a telnet or terminal session if no activity is
detected for this length of time. Only one telnet or terminal session
may be active at one time. This timeout prevents an unattended
session from blocking interactive access to the agent. The default
value is five minutes.
Telnet/ Terminal Password
This option allows modification of the password required for entry
into a telnet or terminal session. The default value is ADTRAN.
Exit
Returns to the ESU 120e Main menu.
8-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Flash D ownload
The ESU 120e uses flash memory that allows software updates via
the EIA-232 port. This menu selection allows you to manually per-
form a flash download using XMODEM. T-Flash is also available to
automate this process.
Quit Session
Terminates the telnet/terminal session.
61200420L1-1
ESU 120e User Manual
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
8-8
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding SNMP
A ppendix A
As local area network (LAN) environments became standardized
over the past ten years, multi-vendor equipment grew with compe-
tition. It became necessary to manage the various vendor equip-
ment from a single control console. Thus, the SNMP emerged as
the standard for managing commercial TCP/IP networks.
The term SNMP broadly refers to the message protocols used to
exchange information between the network and the managed
devices, as well as to the structure of network management data-
bases.
SNMP BASIC COMPONENTS
SNMP has three basic components: Network Manager, Agent, and
MIB.
Network Manager
This is a control program that collects, controls, and presents data
pertinent to the operation of the network devices. It resides on a
network management station.
Agent
This is a control program that responds to queries and commands
from the network manager and returns requested information or
invokes configuration changes initiated by the manager. It resides
in each network device.
1200420L1-1
ESU 120e User Manual
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
MIB
This is an index to the organized data within a network device. It
defines the operating parameters that can be controlled or moni-
tored. When requesting the network manager to retrieve or modify
a particular piece of information about a network device, the net-
work manager transmits the request to that network device. The
agent in that device interprets the incoming request, performs the
requested task, and sends its response to the network manager.
The network manager collects all the data from the various net-
work devices and presents it in a consistent form.
COMMAND S
Using SNMP Version 1, the network manager can issue three types
of commands: GetRequest, GetNextRequest, and SetRequest.
GetRequest
This command retrieves a single item or the first in a series from a
network device.
GetNextRequest
This command retrieves the next item in a series from a network
device.
SetRequest
This command writes information to a network device.
A-2
ESU 120e User Manual
1200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
MESSAGES
The network device issues two types of messages: GetResponse
and Trap .
GetResponse
This message is the response to a network manager GetRequest or
GetNextRequest command.
Trap
This is an unsolicited message issued by a network device to report
an operational anomaly or an alarm condition to the network man-
ager.
These messages are typically encased within informational packets
and transported over the LAN or WAN (wide area network).
ESU 120E SNMP ACCESS
By default, SNMP MIB Browser access to the ESU 120e IP address
with the configured community names, accesses the host. The ESU
120e can also act as an SNMP proxy agent for external units. To
access MIB variables on externally chained devices, append a
period and the Unit ID of the device to the Read and Read/Write
community names. For example, if the Read community name
configured in the ESU 120e is public, specifying "public.3" as the
community name in the SNMP MIB Browser allows reading SNMP
MIB variables from externally chained unit 3.
If the external unit's passcode is not the default, an entry must be
added to the Unit Access Table for SNMP MIB access. See the Unit
Access Table section in Chapter 3: Operation for more information.
However, SNMP traps for the unit can be forwarded without the
entry.
1200420L1-1
ESU 120e User Manual
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
SNMP TRAP CONFIGURATION
Traps received by the ESU 120e from external units and the host
unit are converted into SNMP traps and forwarded to the config-
ured NMS. The source of the trap is uniquely identified at the NMS
by a combination of the IP address of the ESU 120e, and the Unit ID
of the sending device. The Unit ID is present in the trap packet
appended to the end of the trap community packet name, for exam-
ple public.4. It is also included as an Octet String variable (adProd-
PhysAddress) in the trap packet as defined in the individual
product MIBs. The latest versions of the product MIBs, by default,
display the appended trap community name in their descriptions.
Typical steps required for Management Station trap configuration
are loading the device specific MIBs and loading or creating device-
specific Trap Definition Files. The current product MIBs contain
keywords embedded in comments that can be used by some net-
work management platforms to automatically generate Trap Defi-
nitions. Otherwise, the descriptions may be used as a template for
Trap Definitions.
If individual option card port and slot identification is required, it is
present in the four- byte adProdPhysAddress field of the trap
packet. The first two bytes are the Unit ID of the base controller
(least significant byte first). The next two bytes are port and slot
number. This field is the second object identifier in all traps sent
from ESU/TDU products. For traps from the ISU 512, the Unit ID
is the first object identifier. See the product MIBs for more informa-
tion
Definitions for Poll Link Up/Down traps are included in the ESU
120e MIB file: ESU 120e.MIB.
A-4
ESU 120e User Manual
1200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
SNMP MIB BROWSER CONFIGURATION
The following steps are required to configure Network Manager
MIB variable access through the ESU 120e:
1. Load the desired product MIBs on the network management
station. If, for example, the administrator is managing ESU
120e and ISU 512 devices, load ESU 120e.MIB, ISU512.MIB, and
RFC1406.MIB.
2. Create device entries in the NMS database for all units that are
to be managed through the ESU 120e. The host unit should be
configured as the Proxy agent for the external units. The IP
address or host name used for the proxy designation is that of
the ESU 120e.
3. Set community names in the device’s entries for external units
to the ESU 120e community name with the device Unit ID
appended as defined in the previous section ESU 120e SNMP
ACCESS.
4. Set the device timeout for all device entries in the NMS device
database to five seconds, including the host unit.
SNMP MIB FILES
The ESU 120e supports several standard MIBs including MIB-II
(RFC-1213), the DS1 E1/E1 MIB (RFC-1406), and the Ethernet MIB
(RFC-1643). It also supports several ADTRAN enterprise-specific
MIBs including the ADTRAN Product MIB (ADTRAN.MIB), the
ADTRAN DS1 extensions MIB (ADS1.MIB), and all ESU/TDU
Enterprise MIBs, such as ESU 120e.MIB.
The standard MIB files are usually included with most SNMP net-
work management software. The latest version of the ADTRAN
enterprise specific MIBs are available from the ADTRAN anony-
mous ftp site (ftp.adtran.com), or by dial-up from the BBS (205 -
971-8169). The MIB files are also located on the ADTRAN WWW
site at http://www.adtran.com.
1200420L1-1
ESU 120e User Manual
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
A-6
ESU 120e User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1200420L1-1
Connector Pinouts
A ppendix B
WIRING
Network interface Connector
The network connections are as follows:
Connector type 15-pin female D connector
Table B-1. Network Pinouts
Pin
1
Name
Tx data (output)
Frame ground
R x data (input)
Frame ground
Frame ground
Frame ground
Tx data (output)
R x data (input)
2
3
4
5
7
9
11
6,8,10,12,13,14,15 Not Used
61200420L1-1
ESU 120e User Manual
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
Control In/ Chain In
This is used an as EIA-232 port for connection to a computer or
modem (Control In) or to another ESU 120e for TSU 100 (Chain In).
See Table B-2 for the pinout of the control/chain-in connector.
Connections
The chain-in connections are as follows:
Connector type
Part Number
RJ-48
AMP# 555164-2
Table B-2. Control In/ Chain-in Pinout
Pin
1
Name
GND
Description
Ground-connected to unit chassis
R equest to send - flow control
Data received by the ESU 120e
2
R TS
3
R XDA TA
UNUSED
TXDA TA
UNUSED
CTS
4
5
Data transmitted by the ESU 120e
Clear to send - flow control
6, 7
8
B-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
Chain Out
This is used to connect to another ESU 120e chain-in connector. See
Table B-3 for the pinout of the chain-out connector.
Connections
The chain-out connections are as follows:
Connector type
Part Number
RJ-48
AMP# 555164-2
Table B-3. Chain-Out Connector Pinout
Pin
Name
GND
Description
1
Ground-connected to unit chassis. Connected to
GND of next unit (pin 10)
2
3
UNUSED
TX DA TA
Data transmitted to chained units by the ESU
120e. Connect to R X DA TA of the next unit
(chain-in pin 3)
4
5
UNUSED
R X DA TA
Data received from chained units by the ESU
120e. Connect to TX Data of the next unit
(chain-in pin 5)
6, 7,8 UNUSED
61200420L1-1
ESU 120e User Manual
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
D ata Port Interface
Connector type
25-pin female D connector
Table B-4. Nx56/ 64 Pin Assignments for EIA-530 and V.36
Pin
1
EIA/CCITT
Shield
Description
Source
_
2
BA (A )/103
BB (A )/104
CA (A ) /105
CB (A ) /106
CC (A )/107
A B /102
Transmitted Data (TD-A )
R eceived Data A (R D-A )
R equest to Send A (R TS-A )
Clear to Send A (CTS-A )
DCE R eady (DSR -A )
DTE
3
DCE
DTE
DCE
DCE
DTE
4
5
6
7
Signal Ground
8
CF (A ) /109
DD (B) /115
CF (B)/109
DA (B) /113
DB (B)/114
CB (B)/106
BA (B)/103
DB (A )/114
BB (B) /104
DD (A ) /115
Not supported
CA (B)/105
Not supported
Not supported
CC (B)/107
Not supported
DA (A ) /113
Not supported
R eceived Line Detector (DCD-A ) DCE
R eceiver Element Timing (R C-B) DCE
R eceived Line Detector (DCD-B) DCE
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
External Clock B (ETC-B)
DTE
Transmit Element Timing (TC-B) DCE
Clear to Send (CTS-B)
Transmitted Data (TD-B)
DCE
DTE
Transmit Element Timing (TC-A ) DCE
R eceived Data (R D-B) DCE
R eceiver Element Timing (R C-A ) DCE
R equest to Send (R TS-B)
DTE
DCE R eady (DSR -B)
DCE
DTE
External Clock A (ETC-A )
B-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode
Pin
1
Name
GND
TD-A
R D-A
R TS
CCITT
Description
Protective GND
Tx Data A
Source
_
2
103
104
105
106
107
102
109
115
DTE
3
R x Data A
DCE
DTE
4
R TS
5
CTS
CTS - Clear to Send
DSR - Data Set R eady
Signal GND
R ec Line Det
R x Timing B
Not Used
DCE
DCE
DTE
6
DSR
7
GND
DCD
R C-B
8
DCE
DCE
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ETC-B
TC-B
113
114
External Clock B
Tx Timing B
DTE
DCE
DCE
DTE
Not Used
TD-A
TC-A
R D-B
R C-A
103
114
104
115
Tx Data B
Tx Timing A
R x Data B
DCE
DCE
DCE
R x Timing A
Not Supported
Not Used
108
113
Not Supported
Not Supported
Not Supported
Not Used
ETC-A
External Clk A
Not supported
DTE
61200420L1-1
ESU 120e User Manual
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester
Part # 1200285L1
DB25P Pin 34 Pin
Name
Protective GND
Tx Data A
1
2
A
P
3
R
C
D
E
B
F
Rx Data A
4
RTS or RR
5
CTS
6
DSR
7
Signal GND
R ec Line Sig Det (DCD)
R x Signal Timing B
Not Connected
External Clock B
Tx Signal Timing B
Not Connected
Tx Data B
8
9
X
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
W
A A
S
Y
T
Tx Signal Timing A
R x Data B
V
J
R x Signal Timing A
Local Loopback
Not Connected
DTR
H
B
R emote Loopback
Not Connected
Not Connected
External Clk A
Test Mode
U
K
B-6
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode
Pin
1
Name
Description
Protective GND
Source
_
2
T(A )
R (A )
C(A )
I(A )
Transmit A (TD-A )
R eceive A (R D-A )
Control A (R TS-A )
Indication A (CTS-A )
DSR-A
DTE
3
DCE
DTE
4
5
DCE
DCE
DTE
6
7
G
Signal GND
9
S(B)
X(B)
I(B)
Signal Timing B ( R C-B)
DTE Tx Signal Timing B (ETC-B)
Indication B (CTS-B)
Transmit B (TD-B)
Receive B (RD-B)
DCE
DTE
11
13
14
16
17
19
22
24
DCE
DTE
DCE
DCE
DTE
T(B)
R(B)
S(A)
C(B)
Signal Timing A (RC-A)
Control B (R TS-B)
DSR -B
DCE
DTE
X(A )
DTE Tx Signal Timing (ETC-A )
Pins 8, 10, 12, 15, 20, 21,22,23,25 are not used in this mode
61200420L1-1
ESU 120e User Manual
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
Table B-8. Adapter Cable D B25 to X.21, D B15 Connector
Name
Protective GND (Shield)
Signal GND
Control A
DB25Pin
DA15S Pin
1
7
1
8
4
3
Control B
19
8
10
5
Indication A
Indication B
Transmit A
10
2
12
2
Transmit B
14
3
9
Receive A
4
Receive B
16
15/17
9/12
11
6
Signal Timing A
Signal Timing B
13
Base D rop (PBX)
The Drop has a DB-15 female connector as defined in Table B-9.
Table B-9. Pinout Connectors for Terminal Interface
Pin
1
Name
R x Data (output)
2
Frame Ground
Tx data (input)
Frame Ground
R x data (output)
Tx data (input)
3
4
9
11
5,6,7,8,10, 12, 13, 14,15 Not used
B-8
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
10BaseT
This is used to connect the ESU 120e to the local area network.
Connections
The required wiring connections are:
Connector type
(USOC)Part Number
Shielded RJ48
AMP # 555164-1
Table B-10. 10BaseT Pinout
Pin
1
Name ( To Nic)
TX1
TX2
RX1
RX2
2
3
6
61200420L1-1
ESU 120e User Manual
B-9
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix B. Connector Pinouts
B-10
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
System Messages
A ppendix C
ALARM MESSAGES
This appendix lists and defines the alarm and status messages that
appear on the ESU 120e screen.
Network Interface (NI)
Loss of Frame
NI unable to frame align with incoming FAS /NFAS framing
pattern. Remote Alarm (Bit 3 of NFAS word) is transmitted out
the network interface. AIS (unframed ones) is transmitted out
the drop port.
Loss of TS16MF NI unable to sync on TS16 multiframe signal. Valid only when
CAS/TS16 framing enabled. Remote multiframe Alarm is
transmitted out the network interface. ASI is transmitted out
the drop port in TS16 only.
Remote Alarm Remote alarm signal (Bit 3 of NFAS word) being received at
network interface.
Remote MF
Alarm
Remote multiframe alarm signal (Bit 6 of TS16 for three
consecutive multiframes) being received at network interface.
AIS Received
Unframed ones being received at network interface. AIS
transmitted out drop port interface.
TS16 AIS RCVD Unframed ones being received in TS16 on network interface.
Remote multiframe alarm transmitted out network interface.
AIS in TS16 is transmitted out drop port.
Loss of CRC-4
NI unable to sync on CRC-4 multiframe signal. Valid only
when CRC-4 framing is enabled. Remote Alarm is transmitted
out the network interface. AIS is transmitted out the drop port.
Loss of Signal
No signal detected at NI
1200420L1-1
ESU 120e User Manual
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix C. System Messages
Nx56/ 64 Interface
The following messages indicate an alarm condition on the Nx56/
64 card:
Clock Slip
PLL Alarm
Difference in frequency of the data clock at the
network and DTE
Unable to achieve Phase Locked Loop on the
clock provided by the network interface.
Zeros Alarm All zeros (0s) data being sent toward the network
interface
FIFO Alarm
Error in propagation of data through the FIFOs
No EXT Clock No external transmit clock at DTE (only appears
if EXT CLK is selected)
C-2
ESU 120e User Manual
1200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix C. System Messages
D rop Port Interface
The following messages indicate a condition on the Base Drop (PBX) in-
terface:
Loss of Frame
Drop Port unable to frame align with incoming
FAS/NFAS framing pattern. Remote Alarm
(Bit 3 TS0 NFAS word) is transmitted on the
drop port interface.
Loss of TS16 MF
Drop Port unable to sync on TS16 multiframe
signal. Valid only when CAS/TS16 framing
enabled. Remote multiframe Alarm is
transmitted out the drop port interface. AIS is
transmitted out the drop port in TS16 only.
Loss of CRC-4
Drop Port unable to sync on CRC-4 multiframe
signal. Valid only when CRC-4 framing is
enabled. Remote Alarm is transmitted out the
drop port interface. AIS is transmitted out the
drop port.
Loss of Signal
Remote Alarm
No signal detected at the drop port interface.
Remote alarm signal (Bit 3 of NFAS word)
being received at drop port interface.
Remote MF Alarm
Remote multiframe alarm signal (Bit 6 of TS16
for three consecutive multiframes) being
received at drop port interface.
AIS Received
Frame Slip
Unframed ones being received at the Drop Port
interface.
Indicates clock being received at drop port is
different frequency than network clock.
Excessive BER
Excessive Bit Error ratio. A bit error ratio of
-3
greater than 1X10 is being recieved at the
Drop Port interface.
1200420L1-1
ESU 120e User Manual
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix C. System Messages
Status Messages
Network Interface (NI)
Payload On
Line On
Payload loopback activated
Loopback off
Loopback Off All loopbacks deactivated
Factory Restore Factory setting restored
Power On
Self-Test
Unit powered on
Internal self-test performed
Nx56/ 64 Interface
The following messages indicate the status of the Nx56/64 card:
Loop Up
Data is looped at both the network interface
and DTE interface of the card
Remote Loop Up Sending V.54 pattern in an attempt to loop up a
remote device
511 Pattern On
Sending 511 pattern towards the network
interface
Loop Down
Data is no longer looped back at the network
interface or DTE interface
511 Pattern Off
No longer sending 511 pattern towards the
network interface
D rop (PBX) Interface
The following messages indicate the status of the Drop interface:
Frame Slip
Indicates a Frame Slip has occurred on the Drop
interface; this is present in Alarm History only
Line Loop Up
Port Loop Up
Loopdown
Line loopback activated
Port loopback activated
Loopback has been deactivated
C-4
ESU 120e User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1200420L1-1
Specifications
A ppendix D
ELECTRICAL SPECIFICATIONS
Network Interface
Electrical G.703
Framing G.704
Jitter
CRC-4, FAS,CAS
G.823
HDB3
Line Code
Mechanical
75 Ω - BNC; 120 Ω - DB15
Receiver Sensitivity -30dB
1200420L1-1
ESU 120e User Manual
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix D. Specifications
Nx56/ 64 D rop Port Interface
Nx56/ 64 (V.35 Interface)
Electrical
CCITT V.35 Synchronous, V.11 (x.21), EIA
530
Rates
56kbps - 1.984Mbps in 56k or 64k
increments
Clock Options
Tests
Normal/Inverted and internal/external
Local Loopback (bilateral)
Remote Loopback (V.54)
Test Pattern
511 with errored seconds display and
error inject capability
Data inversion
Menu selectable
1s Density Protection
Force 1s to network after one second of
consecutive zeros from DTE. User
selectable (On/Off)
CTS, DCD, DSR
Connector
Normal or Force On
DB 25
D rop Port Interface
Electrical G.703
Framing G.704
Jitter
CRC-4, FAS,CAS
G.823
Line Code
HDB3
Mechanical
120 Ω - DB15
D-2
ESU 120e User Manual
1200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix D. Specifications
Management Interfaces
Chain In/ Out Ports
Interface Devices PC Serial Port, Modem or SLIP connection to
router
Interface Type
Data Rates
Data Format
Protocols
EIA-232
9600, 2400, 1200, 2400, 4800, 9600, 19200, 38400
EIA-232 N81
T-Watch/ADLP, ATEL/ADLP, TCP/IP/SLIP
RJ-45
Connector
10BaseT Interface
Interface
Rate
IEEE 802.3 Compliant
10 Mbps
Connector
Receiver
Protocols
RJ45
Accepts signal > 300mV
Network: IP
Transport:TCP, UDP
Service: SNMP, TELNET, ICMP, ARP, PING, T-
WATCH
Option Slot Interface
Interface ADTRAN proprietary, accepts ESU Option
Modules.
1200420L1-1
ESU 120e User Manual
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
A ppendix D. Specifications
Chassis Specifications
Height
Width
Less than 3.5 inches (will fit in a 2U rack
mount opening)
Two units will fit within a 19-inch rack
Environmental Specifications
Input Power
Fuse
90-250VAC, 50/60 Hz
0.6A, 250V
Operating
0 deg C to 45 deg C
Temperature
Max Power
15 Watts
0.2 A
Consumption
Max Current
D-4
ESU 120e User Manual
1200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Numerics
0.1 Nx56/64 Port Configuration
(Port Config) Menu Items 5-17
0.2 DSX-1 Port Configuration
(Port Config) Menu Items 5-19
10BASET Interface D-3
Cancel Key, ESU 120e front
panel 3-1
Chain In/Out Ports D-3
Chain Port Output 2-6
change/set a passcode, how to 6-
10BaseT Interface 2-6
10BaseT Pinout B-9
Chassis Specifications, ESU
A
Config, front panel menu option
Configuration Menu Tree 5-2
Control Port Input 2-6
CSU Status, LEDs 3-3
customer service ix
Adapter Cable DB25 to X.21,
Db15 Connector B-8
Adapter Cable, DB 25 to V.35,
34-Pin Winchester B-6
1
ADTRAN Web Site iii
alarm and status messages on
ESU 120e screen C-1
D
alarm,clear port 4-6
applications, ESU 120e 1-3
data port identification 3-7
Drop (PBX) Interface 2-6
Drop (PBX) Interface, status
messages C-4
B
board level tests 2-7
Drop
Port
Interface,
specifications D-2
Drop Port Interface, system
61200420L1-1
ESU 120e User Manual
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
messages C-3
DSU/Drop Status 3-3
DTE timing 5-7
Initialization 2-7
L
E
LCD Window, ESU 120e front
LED Descriptions, ESU 120e front
electrical specifications for ESU
120e D-1
E-mail, for Y2K info iii
Enter Key, ESU 120e front panel
3-1
Enter Passcode from Other Menus,
how to 6-2
Environmental Specifications D-4
Equipment customer provides 2-1
errors, network interface 4-3
ESU 120e Clock Sources 5-5
M
Management Interfaces D-3
map xchng 5-13
menu items for map exchange
menu 5-13
Messages, network device for
SNMP A-3
ESU
120e
Applications 1-3
N
ESU 120e Features 1-2
ESU 120e Overview 1-1
ESU 120e snmp access A-3
ESU Option Modules 1-2
ESU120e Interfaces 2-5
Example 2-8
Network 7-2
Network (NI) Menu Items 5-3
messages C-4
network performance reports 4-2
Network Pinout B-1
Network Test Interface 2-5
F
Faxback Document Line, Y2K iii
front panel LCDs of main menu,
descriptions 3-8
Front Panel Menu Structure 3-7
Front Panel, operation 3-1
NI ERRORS 4-3
Normal Power-Up Procedure 2-9
Numeric Keypad, ESU 120e front
panel 3-1
G
Nx56/64
specifications D-2
Nx56/64 Interface, alarm message
(V.35
Interface),
Grounding 2-2
Grounding Instructions for ESU
120e 2-2
Index-2
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C-2
Nx56/64
messages C-4
Nx56/64 Pin Assignments for
EIA-530 Mode B-4, B-5
Nx56/64 Pin Assignments for
V.11/x.21 Mode B-7
self-testing at power up 2-6
setting unit identification, how to
6-4
Setting up ESU 120e to work with
Interface,
Nx56/64 Serial Interface 2-5
Setting up ESU 120e to work with
T-Watch PRO over LAN 3-9
Shift, ESU 120e front panel 3-1
shipping damages, what to do 2-1
SNMP mib browser configuration
A-5
O
Option module architecture for
ESU 120e 1-3
Option Slot Interface D-3
SNMP MIB Files A-5
P
TRAP
passcode, special features 6-3
Pinout Connectors for Terminal
Interface B-8
port configuration 5-17
port status 4-5
CONFIGURATION A-4
Status, front panel menu option 3-8
T
port utility 6-5
power connection 2-2
power cord 2-2
power up, normal procedure 2-9
power-up testing 2-6
Product Matrix, Y2K info iii
Telnet, connect to ESU 120e with
monitoring unit 3-10
Test Menu Tree 7-1
R
Test, front panel menu option 3-8
Rear Panel layout 2-4
remote port 4-6
DTE 5-7
Router, PBX, Video Application
Set Up 1-3
T-Watch PRO 3-8
T-Watch PRO, capabilities 3-8
S
U
self test 7-2
Unit 5-11
61200420L1-1
ESU 120e User Manual
Index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
unit ID 6-4
W
unit level tests 2-7
Unit menu 5-11
Unpack 2-1
Wiring, Connector Pinouts B-1
unpack, inspect, power up 2-1
Up and Down Arrows, ESU 120e
front panel 3-1
Y
Y2K Project Line iii
Using SNMP with ESU 120e 3-10
Util, front panel menu option 3-8
Utility Menu Tree 6-1
Y2K Readiness Disclosure iii
Y2K, Faxback Document Line iii
Index-4
ESU 120e User Manual
61200420L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Support Information
Presales Inquiries and Applications Support
Please contact your local distributor, ADTRAN Applications Engineering,
or ADTRAN Sales:
Applications Engineering (800) 615-1176
Sales
(800) 827-0807
Post-Sale Support
Please contact your local distributor first. If your local distributor cannot
help, please contact ADTRAN Technical Support and have the unit serial
number available.
Technical Support
(888) 4ADTRAN
Repair and Return
If ADTRAN Technical Support determines that a repair is needed, Technical
Support will coordinate with theCustomer and Product Service (CaPS) de-
partment to issue an RMA number. For information regarding equipment
currently in house or possible fees associated with repair, contact CaPS di-
rectly at the following number:
CaPS Department (256) 963-8722
Identify the RMA number clearly on the package (below address), and re-
turn to the following address:
ADTRAN, Inc.
CaPS Department
6767 Old Madison Pike
Progress Center
Building #6, Suite 690
Huntsville, AL 35807
RMA # _____________
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|