OWNERS
MANUAL
E
T
A
R
W
LO
F
Model No.
45-0187
BROADCAST SPREADER 160
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
Assembly
Operation
Maintenance
Repair Parts
303 WEST RAYMOND
SULLIVAN, ILLINOIS 61951
PRINTED IN USA
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
D
E
C
F
H
I
J
G
K
N
P
O
L
M
FIGURE 2 - HARDWARE PACK
KEY QTY.
DESCRIPTION
KEY QTY.
DESCRIPTION
A
B
C
D
E
6
8
1
1
1
Hex Bolt 1/4-20 x 1-3/4" Long
Hex Lock Nuts 1/4-20 Thread
Hand Knob
Nylon Washer
Cotter Pin 3/32" x 3/4" Long
I
J
2
2
4
1
2
1
1
1
Hex Lock Nuts 3/8-16 Thread
Spacers
Flat Washers 1-5/8" O.D.
Grip
Hex Bolt 1/4-20 x 5/8" Long
Flow Control Link
Extension Spring
K
L
M
N
O
P
F3 latF
G
H
Washer
1/4"
Standard
2
2
Hex Bolts 3/8-16 x 1-1/4" Long
Lock Washers 3/8" I.D.
Cotter Pin 1/8 x 1-1/2" Long
I
H
A
3/8" LOCK NUT
M
G
3/8" LOCK WASHER
B
1/4"x 5/8"
1/4" LOCK NUT
F
K
3/8" x 1-1/4"
D
1/4"x 1-3/4"
1/4" WASHER
NYLON WASHER
25/32" WASHER
FULL SIZE HARDWARE REFERENCE CHART
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
3/8" FLAT
WASHER
TOOLS REQUIRED FOR ASSEMBLY
CROSSOVER
TUBE
3/8" LOCK
NUT
(1)
(2)
(2)
Pliers
Open or Boxed End Wrench
9/16" Open or Boxed End Wrench
1. Remove the spreader, loose parts and hardware
package from the carton. See figures 1 and 2.
2. Turn the spreader upside down as shown in figure
3, so that it rests on the hopper.
3. Remove the 3/8" hex bolt, flat washer and hex lock
nut from the center of the crossover tube and shaft
support plate. See figure 3.
HTICH
TUBE
3/8" HEX BOLT,
FLAT WASHER
AND HEX NUT
CROSSOVER
TUBE
3/8" x 2"
HEX BOLT
FIGURE 4
5. Assemble two hitch braces to the inside of the
hopper frame, one on each side, using two 1/4" x
1-3/4" and two 1/4" hex lock nuts. See figure 5.
DO NOT TIGHTEN AT THIS TIME.
6. Align the holes in the ends of the two hitch braces
with the nearest hole in the hitch tube, secure with
1/4" x 1-3/4" hex bolt and 1/4" hex lock nut. See
figure 5.
7. Tighten all hex nuts and bolts, following same
sequence as assembled in steps 4, 5 and 6. DO
NOT COLLAPSE TUBE WHEN TIGHTENING.
8. Assemble one spacer, and one 1-5/8" dia. flat
washer to each side of axle. See figure 5.
SHAFT
SUPPORT
HOPPER
PLATE
FRAME
AXLE
1-5/8" DIA.
FLAT
FIGURE 3
WASHER
1/4" LOCK
NUT
4. Place the hitch tube up against the crossover
tube, align the holes in the hitch tube, crossover
tube and shaft support plate, assemble with 3/8"
hex bolt, 3/8" flat washer and 3/8" hex lock nut,
removed in step 3. See figures 3 and 4. MAKE
ONLY FINGER TIGHT AT THIS TIME.
SPACER
NOTE
WHEN SPREADER IS UP SIDE DOWN,
AS SHOWN IN FIGURE 4, HITCH TUBE
IS UNDERNEATH CROSSOVER TUBE
1/4" x 1-3/4"
HEX BOLT
FIGURE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Place wheel assembly without hole through hub
(air valve to the outside) onto axle end having the
smallest and secure with 1-5/8" dia. flat washer
and 1/8" x 1-1/2" cotter pin. See figure 6. Use
extra 1-5/8" diameter flat washer if needed to take
up play.
11. Turn the broadcast spreader over so that it rests
on its wheels.
12. Assemble the hitch bracket to the hitch tube. See
figure 8. Secure with two 3/8" x 1-1/4" hex bolts,
3/8" lock washers and 3/8" lock nuts. See figure
8.
AXLE
3/8" x 1-1/4" HEX BOLT
1-5/8" DIA.
FLAT WASHER
HITCH TUBE
3/8" LOCK WASHERS
3/8" HEX LOCK NUTS
HITCH BRACKET
COTTER
AIR
PIN
VALVE
FIGURE 8
13. Assemble the flow control link (the end with the
smallest hole) to the flow control arm using one
1/4" x 5/8" hex bolt and one 1/4" hex lock nut. See
figure 9. DO NOT OVER TIGHTEN, FLOW CON-
TROL LINK MUST PIVOT FREELY.
FIGURE 6
10. Place the drive wheel onto the axle (air valve to
the outside) and secure with 1/4" 1-3/4" hex bolt
and 1/4" hex lock nut. See figure 7.
14. Place the vinyl grip on the flow control arm. See
figure 9.
VINYL GRIP
1/4" x 1-3/4" HEX BOLT
FLOW
CONTROL
LINK
FLOW
CONTROL
ARM
1/4" HEX
LOCK
NUT
1/4" x 5/8"
HEX BOLT
DRIVE WHEEL
AIR VALVE
SMALLEST HOLE
FIGURE 9
1/4" HEX LOCK NUT
FIGURE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Hook free end of flow control rod through hole in
slide gate bracket located near bottom of hopper.
See figure 12.
15. Assemble the flow control arm to the flow control
mounting bracket using one 1/4" x 5/8" hex bolt
and one 1/4" hex lock nut. See figure 10. DO NOT
OVER TIGHTEN FLOW CONTROL ARM MUST
PIVOT FREELY.
16. Hook one end of extension spring through small
hole near bend in flow control rod and the other
end through the hole in flow control mounting
bracket. See figure 10.
SLIDE
GATE
BRACKET
HOPPER
FLOW
CONTROL
LINK
FLOW CONTROL ARM
FLOW CONTROL
MOUNTING
BRACKET
FLOW
CONTROL
ROD
FLOW
CONTROL
ROD
FIGURE 12
EXTENSION
SPRING
1/4" x 5/8"
HEX BOLT
19. Assemble flow control mounting bracket to the
hitch tube using two 1/4" x 1-3/4" hex bolts, two 1/
4" flat washers and two 1/4" hex lock nuts. See
figure 13. DO NOT TIGHTEN AT THIS TIME.
1/4" LOCK NUT
FIGURE 10
17. Place 1/4" flat washer on end of flow control link,
align with slot in flow control mounting bracket
and insert end of flow control rod through slot and
hole in flow control link. Secure with 3/32" cotter
pin. See figure 11.
FLOW CONTROL
MOUNTING BRACKET
FLOW CONTROL
FLOW CONTROL
ROD
MOUNTING BRACKET
1/4" x 3/4"
HEX BOLTS
1/4" HEX
LOCK NUTS
1/4" FLAT
WASHER
1/4" FLAT
WASHERS
3/32" COTTER
PIN
FLOW CONTROL LINK
FIGURE 11
FIGURE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Assemble the flow control gauge onto the flow
control mounting bracket as shown in figure 14.
Secure with nylon washer and hand knob.
OFF
PLASTIC KNOB
NYLON
WASHER
FLOW
CONTROL
GAUGE
FLOW
CONTROL
ARM
FLOW CONTROL
MOUNTING BRACKET
FIGURE 14
21. Move flow control arm to off position and slide flow
control mounting bracket toward hopper until clo-
sure plate (located in bottom of hopper) is com-
pletely closed. Tighten 1/4" hex lock nuts as-
sembled in step 19. See figure 14.
22. Pre-lubricate per lubrication section on page 9
before operating spreader.
Download from Www.Somanuals.com. All Manuals Search And Download.
MATERIAL
TYPE
Flow Rate Setting
At 3 M.P.H.
OPERATION
The application spray pattern should overlap to insure
uniform coverage at the edges. The approximate
distance between each pass is shown in the applica-
tion diagram. See figure 15.
Light
Heavy
FERTILIZER
GRASS SEED
ICE MELTER
Granular
Pelleted
3
5
5
7
APPLICATION DIAGRAM
Fine
Coarse
2
6
4
8
Granular
Pelleted
6
6
8
8
8' to
10'
1. Determine approximate square footage of area to
be covered and estimate amount of material re-
quired.
OVERLAP
2. With flow control arm in the off position, set flow
rate gauge at the number indicated in flow rate
chart - light or heavy application rate. Also refer
to the bag instructions for manufacturers recom-
mended settings.
FIGRUE 15
FLOW RATE ADJUSTMENT
3. Break up lumpy fertilizer as you fill hopper.
(SEE FIGURE 16)
4. To broadcast, always start tractor in motion be-
fore opening closure plate. Do not allow tractor
to sit stationary with flow control arm in the on
position. If fertilizer is accidentally deposited to
heavily in a small area, soak down thoroughly with
garden hose or sprinkler to prevent burning of
lawn.
1. Push back on the flow control arm to the off
position and pull forward to the on position. The
higher the number on the flow rate gauge the
larger the opening in the bottom of the hopper.
2. REFER TO FLOW RATE CHART AND INSTRUC-
TIONS ON FERTILIZER BAG TO SELECT
PROPER FLOW RATE SETTING.
3. Loosen the hand knob to set the flow gauge to the
desired flow setting and tighten the hand knob.
4. Always move flow control arm to off position be-
fore stopping or turning spreader.
5. The spreader should be moving before you move
the flow control arm to the on position.
IMPORTANT: Application rates (shown on
chart) are affected by humidity and moisture
content of material (granular and pellet); there-
fore, minor setting adjustments may be neces-
sary to compensate for this condition. The
rate chart is calculated for light and heavy
application. The faster you drive, the wider the
broadcast width. A variation in speed will
determine the flow rates and width of broad-
cast.
FLOW CONTROL ARM
HAND KNOB
CAUTION
When broadcasting weed control fer-
tilizers make sure broadcast pattern
does not hit evergreen trees, flowers
or shrubs.
FLOW RATE GAUGE
FIGURE 16
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Heavy moisture conditions may require a cover
over the hopper to keep contents dry. The vinyl
cover acts as a wind and moisture shield, but
should not be used as a rain cover. See figure 18.
MAINTENANCE & STORAGE
1. Do not store spreader with any material in hopper.
2. Clean your spreader after use. Flush thoroughly
with water.
VINYL
COVER
3. If for any reason the axle, gear and sprocket
assembly is disassembled, be sure to mark posi-
tion of parts as they are removed. Drive wheel
and sprocket position determine relation direction
of spreader plate. With reassembly of gear and
sprocket use shim washers as needed for mini-
mum backlash. Add grease to gear and sprocket.
E
RAT
W
FLO
4. If agitator wire becomes damaged or worn it can
be replaced. Loosen 3/8" lock nut on the top of
sprocket shaft until agitator wire is free. Remove
old agitator wire from hole in agitator sleeve and
replace with new agitator wire. Position agitator
wire so that sprocket shaft turns freely and tighten
3/8" lock nut on top of sprocket shaft. See figure
17.
FIGURE 18
LUBRICATION
(SEE FIGURE 19)
SPROCKET
SHAFT
1. Apply a little automotive grease to the sprocket
and gear.
3/8" LOCKNUT
2. Oil nylon bushings on sprocket shaft as shown in
figure 19.
3. Oil axle/shaft bushing on axle as shown in figure
19.
AGITATOR
WIRE
AGITATOR
SLEEVE
4. Oil right hand wheel bearing as needed.
FIGURE 17
OIL
5. Keep tires inflated to 15-20 P.S.I. Do not over
SPROCKET
SHAFT
inflate.
GREASE
MAXIMUM TIRE PRESSURE 30 PSI
OIL
OIL
FIGURE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS BROADCAST SPREADER MODEL 45-0187
56
58
40
37
60
39
9
1
4
16
E
T
A
R
W
O
L
F
37
40
A
7
40
9
9
57
45
31
9
5
39
30
53
B
37
58
3
35
6
9
34
26
48
38
A
54
33
28
51
61
27
24
44
23
9
4
52
39
9
C
11
36
19
10
45
C
D
32
8
29
E
41
49
B
59
42
43
13
7
19
12
47
9
18
23
24
38
22
21
20
9
21
59
37
E
55
7
17
35
14
D
51
51
50
37
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS LIST FOR BROADCAST SPREADER MODEL 45-0187
REF. PART QTY. DESCRIPTION
REF. PART QTY. DESCRIPTION
NO.
NO.
NO.
1
NO.
44480
43882
62482
44462
23753
23758
43082
23756
43013
43808
43084
43086
43064
44487
44458
44459
23687
23522
43851
43871
1
6
1
1
1
1
5
1
18
1
2
2
2
1
1
1
1
1
2
1
5
1
2
2
1
1
1
1
1
1
1
Hopper
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
43070
41576
44469
23525
23762
1509-069
43866
1543-069
43088
23755
62732
62474
23757
44101
23533
43000
43848
43087
43093
43009
43849
44285
43054
43003
43962
44566
43012
R19111116
23697
46055
44659
3
2
1
2
1
3/8" Flat Washer
Bolt, Hex 3/8-16 x 1-3/4" Lg.
Flow Control Rod
Brace, Hitch
2
Rivet
3
4
Ass'y - Guide Closure
Tube Frame
5
6
7
8
Slide Gate Angle Bracket
Slide Gate Bracket
Nut, Hex Lock 3/8"
Flow Control Link
Nut, Hex Lock 1/4-20 Thread
Tube Crossover
Shaft, Support
12 Bolt, Hex 1/4-20 x 1-3/4"
2
9
9
1
1
1
1
1
1
1
1
2
1
4
1
1
1
2
1
1
3
3
1
1
1
Bolt, Hex 1/4-20 x 5/8" Lg.
Washer, Nylon
Washer, Flat 1/4" Std
Gauge, Flow Control
Ass'y. Flow Control Mount
Ass'y Gear
Flow Control Arm
Cotter Pin 3/32" x 3/4" Lg.
Plate, Closure
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Bolt, Hex 5/16" x 1-3/4"
Lock Washer, Spring 5/16" ID
Nut, Hex Lock 5/16-18 Thread
Tube, Hitch
Wheel, Ass'y 16" x 4"
Wheel, Ass'y 16" x 4" W/ Hole
Bracket, Hitch
Spring, Extension
Grip, Flow Control Arm
Bolt, Hex 3/8" x 1-1/4"
Cotter Pin, 1/8" x 1-1/2" Lg.
Washer 1-5/8" OD x 25/32"
Knob, Plastic 1/4-20 Thread
Bushing Derlin .375 ID
Bolt, Hex 3/8" x 2" Lg.
Lock Washer, Spring 3/8" ID
Vinyl Hopper Cover
Spring, Torsion
Bolt, Hex 1/4-20 x 3/4" Lg.
Washer, 5/16" SAE
Strap, Hopper
Pin, 1/8" Dia. x 1" Lg. Spring
Owner's Manual
Shaft, Axle
Pin, Roll 3/16" Dia. x 1.25" Lg.
Bushing, Axle/Shaft
Washer, Flat .78"
Washer, Std. 3/4"
Bearing Flange
Spacer
Shaft, Sprocket
Spreader Plate
Pin, 1/8" x 5/8" Spring
Sprocket - 6T
1540-03
1540-162
44798
44474
23524
04367
43850
44468
43852
23766
43878
2
Bushing, Nylon .375 ID
Sleeve Agitator
Wire, Agitator
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
303 West Raymond
Sullivan, Il. 61951
217-728-8388
Download from Www.Somanuals.com. All Manuals Search And Download.
|