GE TME M580 User Manual

/////alpine®  
Printed in Taiwan R.O.C.  
TME-M580  
5.8-INCH WIDE LCD COLOR MONITOR  
OWNER’S MANUAL  
Please read before using this equipment.  
Points to Observe for Safe Usage  
CAUTION  
This symbol means important instructions.  
Failure to heed them can result in injury or material property damage.  
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the  
cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent  
crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent  
the wire’s insulation from being cut by the metal edge of the hole.  
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified  
accessory parts. Use of other than designated parts may damage this unit internally or may not securely install  
the unit in place. This may cause parts to become loose resulting in hazards or product failure.  
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations  
with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product  
failure.  
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit  
requires special technical skill and experience. To ensure safety, always contact the dealer where you  
purchased this product to have the work done.  
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage  
to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing.  
Operation  
Main power indicator  
PWR  
UP  
DN  
SEL  
DISP  
Remote control sensor  
(The remote control is  
sold separately)  
NOTE: Controllable with Remote Control  
This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point  
the optional remote control transmitter at the remote control sensor.  
Screen Display ON/OFF  
1. Press the PWR button.  
2. To turn off the POWER, press the PWR button again.  
Note:  
If properly connected, the monitors main POWER will turn off when the vehicle’s  
ignition switch is off. If the main power lamp illuminates in the STAND BY mode, the  
vehicle’s battery may be discharged.  
Adjusting the Volume  
1. Adjust the volume level by pressing the  
DN or  
UP button.  
Switching NTSC/PAL  
Switch the movie output type NTSC/PAL in AUX mode.  
1. Press the DISP button for at least 1 second.  
Note: When the movie output type is not compatible, the movie does not output  
normally.  
Switching the source  
1. Press the SEL button. Each press of the button will cycle through the modes as  
follows:  
AUX  
NAVIGATION  
Switching the display mode.  
1. Press the DISP button.  
Each press of the button will cycle through the modes as follows:  
CINEMA  
NORMAL  
WIDE  
ZOOM  
WIDE: Normal images are expanded uniformly in the horizontal direction and are  
displayed over the entire screen.  
CINEMA: Normal images are expanded in the horizontal and vertical directions.  
The top and bottom of the image is cut off. This mode is suited for 16:9 cinema size  
images.  
ZOOM: Normal images are expanded in the horizontal direction and are displayed  
over the entire screen. The expansion ratio increases towards the right and left  
edges of the screen.  
NORMAL: Normal image (4:3)  
Page 4  
Operation  
Reset the Monitor Settings  
1. Press and hold the PWR button for at least 1 second.  
2. Press the SEL button.  
3. Select the Navigation system by pressing the DN or UP button.  
: Standard - Navigation for all others (except Europe)  
: Europe - Navigation for Europe only  
If no key is pressed within 10 seconds, the On-Screen Display wil turn off.  
Adjustment  
1. Press and hold the SEL button for at least 1 second.  
2. Each press of the button will cycle through the modes as follows:  
DIM.  
LEVEL  
COLOR  
BRIGHT  
TINT  
DIMMER  
MONITOR  
MIRROR  
3. Adjust by pressing the  
DN or  
UP button.  
• BRIGHT: Allows the brightness of the picture.  
• COLOR: Change the color balance of the picture.  
Note: It is not adjustable in NAVIGATION (RGB connection) mode.  
• TINT: Adjust the tint of the picture.  
Note: It is not adjustable in NAVIGATION (RGB connection) and PAL mode.  
• DIMMER:  
AUTO: Display illumination will dim when while the car’s parking lights are on.  
LOW: Backlighting is set to the adjusted DIM.LEVEL.  
HIGH: Backlighting is set to its maximum level.  
• DIM.LEVEL: Adjust the backlighting level for LOW DIMMER.  
• MIRROR: Switch the picture to NORMAL/MIRROR (for rear view camera) image.  
4. After completing adjustments, press and hold the SEL button for at least 1 second.  
If no key is pressed within 10 seconds, the OSD will turn off and any changes made  
are automatically set.  
Notes:  
• After turning the system off, a slight ghost of the image will remain temporarily. This  
is an effect peculiar to LCD technology and is normal.  
• Under cold temperature conditions, the screen may lose contrast temporarily. After  
a short warm-up period, it will return to normal.  
• The LCD panel is manufactured using an extremely high precision manufacturing  
technology. Its effective pixel ratio is over 99.99%. This means that there is a  
possibility that 0.01% of the pixels could be either always ON or OFF.  
Page 5  
In Case of Difficulty  
If you encounter a problem, please review the items in the  
following check list. This guide will help you isolate the problem  
if the unit is at fault. Otherwise, make sure the rest of your  
system is properly connected or consult your authorized Alpine  
dealer.  
Symptom  
No function or  
display.  
Cause  
Solution  
Car's ignition is off.  
Turn the ignition on.  
No fuse or blown fuse.  
Check the cause and replace the fuse.  
Check connection and remedy.  
Incorrect connections.  
Vehicle's battery is weak.  
Fluorescent tube is exhausted.  
Check the voltage of vehicle's battery.  
Replace the fluorescent tube*.  
Unclear picture  
display.  
No picture  
display.  
Brightness control is set for  
minimum brightness control.  
Adjust the brightness.  
Incorrect setting of the Input mode.  
Protective circuit is on because of  
high temperature.  
Switch to the correct mode.  
Wait until the temperature inside the vehicle comes down to the  
operating temperature range (45°C).  
Incorrect or open connection with  
the Monitor, AV Interface unit.  
Brightness/Color/Tint control are not  
set to the proper positions.  
Check the connection and remedy.  
Picture color is  
poor.  
Check each control.  
Spots or dotted  
lines/stripes  
appear.  
Caused by neon signs, high-voltage  
power lines, CB transmitter, other  
vehicle's ignition plugs, etc.  
Change the location of your vehicle.  
Unit does not  
operate.  
Monitor's power is not turned on.  
Turn on the monitor's power.  
Navigation  
Navigation system’s power is turned  
off.  
Press the ON/OFF (POWER) button on the navigation system’s  
remote controller to turn the navigation system’s power on.  
screen is not  
displayed or  
navigation  
system’s remote  
controller keys do  
not work.  
* Replacement of the fluorescent tube is not covered under the  
warranty. This is a consumable part subject to wear during  
normal usage.  
Page 6  
Installation  
Caution:  
Do not install the monitor near the front passenger seat air bag system.  
<Mount it using the supplied bracket>  
1. Assemble the supplied bracket and mount the monitor temporarily.  
Note: Always use the supplied bracket or equivalent.  
1
2. Verify the installation location.  
Select a flat surface and temporarily mount the unit. Use adhesive  
tape, etc.  
Notes:  
• Mounting hints  
Top of the monitor should not exceed the top of the dash when  
viewed from the driver’s seat.  
• Use a stable mounting surface.  
• Angle the monitor for easy viewing.  
• In a vehicle with a front passenger air bag, do not install the unit  
where it will interfere with the operation of the safety systems.  
• If the surface of the dash board is finished with other than plastic  
(leather, wooden panel, cloth covered panel, etc.), there will be  
some damage if the bracket is removed.  
2
• Installation close to other equipment (such as a GPS antenna) may  
give rise to mutual interference. Please pay careful attention to the  
installation location and maintain sufficient space between other  
equipment.  
3. Remove the monitor from the bracket.  
4. Peel the protective paper from the double-stick tape on the bracket’s  
base.  
Clean the mounting location with a suitable cleaner.  
Notes:  
• Warm the mounting location with a dryer, etc. and then place the  
bracket into position.  
• Do not apply force or moisture for 24 hours after installation.  
• If the bracket is not attached securely with just the tape, use the  
supplied screws to complete the installation.  
• If the mounted surface is curved slightly, reform the base to fit to its  
shape.  
5. Mount the monitor to the bracket.  
5
Thread the mounting screw into hole at the bottom of the monitor.  
Secure the monitor by tightening the screw. Depending upon the  
location, the bracket can also be mounted using the supplied nut to  
slide into the back of the monitor. Thread the bracket mounting screw  
into the nut. Slide the nut in the channel on the back of the monitor  
and adjust the height and tighten.  
Dress the monitor’s cable using the cord clamp provided.  
6. Adjust the height and angle of the monitor for easy visibility.  
Determine the height and angle. Tighten the height and angle  
adjusting screws to secure the monitor.  
NOTE:  
The A/V Interface box may be mounted in any suitable location. Make sure the box and the wires  
connected to it will not interfere with safely operating the vehicle.  
Mounting the Interface box near the monitor will reduce the need for additional cable extensions.  
This monitor can be mounted in a headrest if desired. A special mounting kit is required and can be  
purchased from your Authorized Alpine dealer. Ask for model KTE-580V.  
Page 7  
Connections  
p
Cautions  
Make connections correctly.  
Improper connections may cause a fire or operation  
failure.  
5
e
q
w
1
Ground lead (Black)  
Connect the lead to a good chassis ground on the  
vehicle. Make sure the connection is made to bare  
metal and is securely fastened using the sheet metal  
screw provided.  
r
2
3
No Connection  
ACC power lead (Red)  
To ACC power lead powered when engine key  
position is ACC.  
6
Battery  
q
t
4
5
No Connection  
Foot brake lead (Yellow/Black)  
Connect this lead to the foot brake lead powered  
when the foot brake is pressed.  
Hand brake lead (Yellow/Blue)  
Connect this lead to the hand brake lead powered  
when the hand brake is pulled.  
y
Chassis  
6
7
8
Dimmer (White/Blue)  
To the Parking Light switch. Backlighting will dim  
when lights are turned on at night.  
Remote control output lead (White/Brown)  
To remote control input lead of ALPINE products used  
in the system.  
8
For the North American Customers only  
7
p
q
w
e
r
Foot brake lamp  
Brake connector  
Foot brake lead  
Foot brake switch  
Hand (parking) brake lamp  
Hand (parking) brake lead  
Hand (parking) brake switch  
3
1
t
y
Specifications  
MONITOR  
Screen Size ......................................................................................................................................... 5.8-type  
Display System ...................................................... Low reflection rear projection type TN liquid crystal panel  
Drive System .................................................................................. Active matrix drive, normally white display  
Number of Picture Elements .................................................................... 280,800 pcs. (H:1200 x V:234 dots)  
Effective Number of Picture Elements .................................................................................... 99.99% or more  
Light Source ................................................... Internal optical system (U-type cold cathode fluorescent tube)  
Dimensions (W x H x D) ........................................................... 160 x 93 x 27 mm (6.30 x 3.66 x 1.06 inches)  
Weight ....................................................................................................................................... 298g (10.5 oz)  
AV Interface Unit  
Dimensions (W x H x D) ............................................................. 72 x 60 x 24 mm (2.84 x 2.36 x 0.95 inches)  
Weight ....................................................................................................................................... 128 g (4.5 oz.)  
Note: Due to continuous product improvement, specifications and design are subject to change without notice.  
SERVICE CARE  
• For European Customers  
Should you have any questions about warranty, please consult your authorized Alpine Dealer.  
• For Customers in other Countries  
IMPORTANT NOTICE  
Customers who purchase the product with which this notice is packaged, and who make this purchase in countries other than  
the United States of America and Canada, please contact your dealer for information regarding warranty coverage.  
Page 8  
TME-M580 + Video and Navigation  
Power Harness Color Code  
1
2
3
4
5
6
7
8
Ground  
Black  
NOT USED  
Accessory  
OPEN  
3 pin EXT.PWR Cord  
Red  
NOT USED  
Foot Brake (+)  
Parking Brake (-)  
Dimmer (+)  
IR Remote  
OPEN  
This cord is only used when using this  
monitor as a navigation monitor only.  
Yellow/Black  
Yellow/Blue  
White/Blue  
White/Brown  
POWER  
MIC/SW TD DISP.  
EX-1  
EX-2  
White Brown  
GPS ANT.  
1
5
10  
6
V
I
D
E
O
13 Pin Nav Cable  
(included with Alpine  
Navigation systems)  
Ext Box Front side  
Ext Box Back side  
8 Pin Power  
Harness  
8 Pin to  
Monitor  
TO BRAIN  
TO NAV  
NOT USED  
8 Pin Din to  
Monitor Brain  
3 Pin EXT  
13 Pin Nav  
Cable to  
Alpine Navigation  
(if running  
nav only)  
Page 9  
TME-M580 + Navigation Only  
Power Harness Color Code  
1
2
3
4
5
6
7
8
Ground  
Black  
NOT USED  
Accessory  
OPEN  
Red  
NOT USED  
Foot Brake (+)  
Parking Brake (-)  
Dimmer (+)  
IR Remote  
OPEN  
Yellow/Black  
Yellow/Blue  
White/Blue  
White/Brown  
POWER  
MIC/SW TD DISP.  
EX-1  
EX-2  
GPS ANT.  
5
1
10  
6
13 Pin Nav Cable  
(included with Alpine  
Navigation systems)  
Ext Box Front side  
Ext Box Back side  
8 Pin Power  
Harness  
8 Pin to  
Monitor  
NOT USED  
TO NAV  
TO BRAIN  
NOTE:  
8 Pin Din to  
Monitor Brain  
3 Pin EXT  
(if running  
nav only)  
13 Pin Nav  
Cable to  
Alpine Navigation  
Please use the tape included to tie  
both cables together to ensure the  
cable will not come loose from the  
monitor.  
Page 10  
TME-M580 + Video Only  
Power Harness Color Code  
1
2
3
4
5
6
7
8
Ground  
Black  
NOT USED  
Accessory  
OPEN  
Red  
NOT USED  
Foot Brake (+)  
Parking Brake (-)  
Dimmer (+)  
IR Remote  
OPEN  
Yellow/Black  
Yellow/Blue  
White/Blue  
White/Brown  
3 pin EXT.PWR Cord  
White Brown  
This cord is only used when using this  
monitor as a navigation monitor only.  
V
I
D
E
O
EXT Box Front side  
EXT Box Back side  
8 Pin Power  
Harness  
8 Pin to  
Monitor  
TO BRAIN  
NOT USED  
NOT USED  
8 Pin Din to  
Monitor Brain  
3 Pin EXT  
(if running  
nav only)  
13 Pin Nav  
Cable to  
Alpine Navigation  
Page 11  
/////alpine®  
ALPINE ELECTRONICS, INC.  
Tokyo office: 1-1-8 Nishi Gotanda,  
Shinagawa-ku, Tokyo 141-8501, Japan  
Tel.: (03) 3494-1101  
ALPINE ITALIA S.p.A.  
Viale C. Colombo 8,  
20090 Trezzano Sul Naviglio (MI), Italy  
Tel.: 02-48 47 81  
ALPINE ELECTRONICS OF AMERICA, INC.  
19145 Gramercy Place, Torrance,  
California 90501, U.S.A.  
ALPINE ELECTRONICS FRANCE  
S.A.R.L.  
(RCS PONTOISE B 338 101 280)  
98, Rue de la Belle Etoile, Z.I. Paris  
Nord II, B.P. 50016, 95945, Roissy  
Charles de Gaulle Cedex, France  
Tel.: 01-48 63 89 89  
Tel.:1-800-ALPINE-1 (1-800-257-4631)  
ALPINE ELECTRONICS OF CANADA, INC.  
7300 Warden Ave., Suite 203, Markham,  
Ontario L3R 9Z6, Canada  
ALPINE ELECTRONICS OF U. K., LTD.  
13 Tanners Drive, Blakelands,  
Milton Keynes MK14 5BU, U.K.  
Tel.: 01908-61 15 56  
Tel.:1-800-ALPINE-1 (1-800-257-4631)  
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.  
6-8 Fiveways Boulevarde Keysborough,  
Victoria 3173, Australia  
ALPINE ELECTRONICS DE ESPAÑA,  
S.A.  
Portal de Gamarra 36, Pabellón, 32  
01013 Vitoria (Alava) - APDO 133,  
Spain  
Tel.: (03) 9769-0000  
ALPINE ELECTRONICS GmbH  
Kreuzerkamp 7, 40878 Ratingen,  
Germany  
Tel.: 945-283588  
Tel.: 02102-45 50  

Heath Zenith 4350 User Manual
GE DECT 6 0 CORDLESS HANDSET 28110 User Manual
Fujitsu Computer Hardware GranPower7000 GP 7000F User Manual
Frigidaire FPIC3695MS User Manual
Epson Bi directional Parallel Interface Board B80818_ User Manual
Cypress Perform CY7C1380D User Manual
Curtis TV2710B User Manual
Creative Avant Prime User Manual
AT T CL81211 User Manual
Adaptec Computer Hardware 44300 User Manual