Instant Broadband™ Series
Cable/DSL Routers
Use this guide to install the following products:
BEFSR41 ver. 2 EtherFast® Cable/DSL Router with 4-Port Switch
BEFSRU31
EtherFast® Cable/DSL Router with USB Port and 3-Port Switch
BEFSR11 ver. 2 EtherFast® 1-Port Cable/DSL Router
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Table of Contents
Chapter 7: Configure the PCs
Overview
Configuring Windows 95, 98, and Millennium PCs
Configuring Windows 2000 PCs
Configuring Windows XP PCs
35
35
36
38
40
Chapter 1: Introduction
The Linksys EtherFast Cable/DSL Router
Features
1
1
1
2
2
3
3
Package Contents for the 4-Port Router (BEFSR41)
Minimum Requirements
Package Contents for the 1-Port Router (BEFSR11)
Minimum Requirements
Chapter 8: Configure the Router
42
Package Contents for the 3-Port Router with USB (BEFSRU31)
Minimum Requirements
An Introduction to LANs and WANs
IP Addresses
4
4
4
5
7
Chapter 9: The Cable/DSL Router’s
Web-based Utility
47
47
47
48
54
55
56
58
59
61
62
63
65
70
71
73
74
Overview
Quick and Easy Router Administration
Setup
Password
Status
DHCP
Log
Security
Network Setup Overview
Chapter 2: Getting to Know the 4-Port
EtherFast Cable/DSL Router
The 4-Port Router’s Rear Panel
8
8
9
The 4-Port Router’s Front Panel LEDs
Help
Chapter 3: Getting to Know the 1-Port
EtherFast Cable/DSL Router
The 1-Port Router’s Rear Panel
Advanced
IP Filtering
Port Range Forwarding
Dynamic Routing
Static Routing
DMZ Host
MAC Address Clone
11
11
12
The 1-Port Router’s Front Panel LEDs
Chapter 4: Getting to Know the 3-Port
EtherFast Cable/DSL Router
The 3-Port Router’s Rear Panel
USB Compatibility
The 3-Port Router’s Front Panel LEDs
14
14
15
16
Appendix A: Troubleshooting
Common Problems and Solutions
Frequently Asked Questions
75
75
88
Chapter 5: Connect the Router
Overview
Connecting Your Hardware Together and Booting Up
Uplinking: Connecting More Devices to the Router
18
18
19
21
Appendix B: Glossary
92
Appendix C: How to Ping Your ISP’s E-mail &
Web Addresses
105
108
Chapter 6: Installing the BEFSRU31’s USB
Port Drivers
Installing the Windows 98 Driver
Installing the Windows 2000 Driver
Installing the Windows Millennium Driver
Installing the Windows XP Driver
22
22
27
31
33
Appendix D: Installing the TCP/IP Protocol
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Chapter 1: Introduction
Appendix E: Twisted-Pair Cabling
Crimping Your Own Network Cables
110
111
The Linksys EtherFast Cable/DSL Router
Congratulations on the purchase of the EtherFast Cable/DSL Router from
Linksys! The Router is the perfect solution for connecting a network of PCs to
a high-speed broadband Internet connection and to an Ethernet network back-
bone. Configurable as a DHCP server for your network, the Router is the only
visible network device on the Internet. The Router also serves as your Internet
NAT firewall, protecting your network’s PCs from being accessed by external
users. All incoming data packets are monitored and filtered. The Router can
also be configured to block internal users’ access to the Internet with IP filter-
ing, as well as to play Internet games, videoconference, and much more. Plus,
the Router supports Universal Plug and Play (UPnP), which allows Windows
XP to automatically configure the Router for various Internet applications,
such as videoconferencing and gaming—making the Router a snap to use.
Appendix F: Finding the MAC Address and IP
Address for Your Ethernet Adapter
112
®
Appendix G: Setting Up AOL
Broadband Cable & DSL
AOL Broadband via Cable
AOL Broadband via DSL
116
116
118
Appendix H: 4-Port Router Specifications
4-Port Environmental Specifications
119
119
Appendix I: 1-Port Router Specifications
120
1-Port Environmental Specifications
120
Now all of your PCs can enjoy lightning-fast broadband Internet connections
and share internal network data. Link them all together and network faster than
you ever thought possible.
Appendix J: 3-Port Router Specifications
3-Port Environmental Specifications
121
121
Features
Appendix K: Warranty Information
Appendix L: Contact Information
122
123
• Connects Your Cable or DSL Modem to Multiple Computers for Internet,
File, and Printer Sharing
• Set Up Your Computers and Router Easily Using Linksys Setup Wizard
• Supports UPnP for Easy Network Configuration
• Supports Enhanced Security Using NAT Firewall and ZoneAlarm Pro* and
PC-cillin Software*
• Access Your Network Remotely over the Internet through Virtual Private
Networking (VPN)—Supports IPSec and PPTP Pass-Through
• Easily Configurable through a Web Browser—Locally and over the Internet
• Administer and Upgrade the Router Remotely over the Internet
• Advanced Security Management Functions for Port Filtering, MAC Address
Filtering, and DMZ Hosting
• 3- or 4-Port, 10/100 Mbps, Built-in Switch Speeds Up Your Gaming and
Multimedia Experience (BEFSRU31 & BEFSR41 ver. 2 only)
• Configurable as a DHCP Server on Your Network
* each sold separately
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
Package Contents for the 4-Port Router (BEFSR41)
EtherFast® Cable/DSL Routers
Package Contents for the 1-Port Router (BEFSR11)
Figure 1-1
Figure 1-2
• One EtherFast Cable/DSL Router with 4-Port Switch
• One Setup Wizard CD-ROM with User Guide Included
• One Power Adapter
• One EtherFast 1-Port Cable/DSL Router
• One Setup Wizard CD-ROM with User Guide Included
• One Power Adapter
• One Fast Start Guide
• One Fast Start Guide
• One Registration Card (not shown)
• One Registration Card (not shown)
Minimum Requirements
Minimum Requirements
•
One Windows PC equipped with:
•
One Windows PC equipped with:
•
•
TCP/IP Protocol,
Internet Explorer 4.0 or Netscape Navigator 4.7 for web-based
configuration,
•
•
TCP/IP Protocol,
Internet Explorer 4.0 or Netscape Navigator 4.7 for web-based
configuration,
•
•
a CD-ROM Drive, and
an Ethernet Adapter with a UTP CAT 5 Network Cable
•
•
a CD-ROM Drive, and
an Ethernet Adapter with a UTP CAT 5 Network Cable
•
Cable or DSL Modem with Ethernet Connection and Internet Access
•
Cable or DSL Modem with Ethernet Connection and Internet Access
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
Package Contents for the 3-Port Router (BEFSRU31)
EtherFast® Cable/DSL Routers
The Router’s firewall (NAT) protects your network of PCs so users on the pub-
lic, Internet side cannot “see” your PCs. This is how your LAN, or network,
remains private. The Router protects your network by inspecting the first pack-
et coming in through the WAN port before delivery to the final destination on
the LAN port. The Router inspects Internet port services like the web server,
ftp server, or other Internet applications, and, if allowed, it will forward the
packet to the appropriate PC on the LAN side.
Remember that the Router’s ports connect to two sides: your 10/100 LAN
port(s) and the Internet WAN port. The LAN port(s) transmit data at 10 Mbps
or 100 Mbps, whereas the broadband port, or WAN port, transmits data at
10 Mbps.
IP Addresses
What’s an IP Address?
IP stands for Internet Protocol. Every device on an IP-based network, includ-
ing PCs, print servers, and routers, requires an IP address to identify its “loca-
tion,” or address, on the network. This applies to both the WAN and LAN con-
nections.
Figure 1-3
• One EtherFast Cable/DSL Router with USB Port & 3-Port Switch
• One Setup Wizard CD-ROM with User Guide Included
• One USB Cable
• One 3.5" Floppy Disk for USB Setup
• One Power Adapter
There are two ways of assigning an IP address to your network devices.
Static IP Addresses
• One Fast Start Guide
A static IP address is a fixed IP address that you assign manually to a PC or
other device on the network. Since a static IP address remains valid until you
disable it, static IP addressing ensures that the device assigned it will always
have that same IP address until you change it. Static IP addresses are com-
monly used with network devices such as server PCs or print servers.
• One Registration Card (not shown)
Minimum Requirements
• Internet Explorer 4.0 or Higher (5.5 Recommended), or Netscape Navigator
4.7 or Higher
• TCP/IP Protocol, Ethernet Adapter, and Ethernet Cable (UTP CAT 5 with RJ-
45 connectors) per PC
• One External Cable or DSL Modem with Ethernet Port and Ethernet Cable
(UTP CAT 5 with RJ-45 connectors)
Note: Since the Router is a device that connects two networks, it needs
two IP addresses—one for the LAN side, and one for the WAN side.
In this User Guide, you’ll see references to the “WAN IP address” and
the “LAN IP address.”
An Introduction to LANs and WANs
Simply put, a router is a network device that connects two networks together.
Since the Router has firewall security (NAT), the only IP address that
can be seen from the Internet for your network is the Router’s WAN IP
address.
In this instance, the Router connects your Local Area Network (LAN), or the
group of PCs in your home or office, to the Wide Area Network (WAN), that
is, the Internet. The Router processes and regulates the data that travels
between these two networks.
However, even this WAN IP address for the Router can be blocked, so
that the Router and network seem invisible to the Internet—see the
Blocking WAN Requests description under IP Filtering in “Chapter 9:
The Cable/DSL Router’s Web-based Utility.”
Think of the Router as a network device with two sides: the first side is made
up of your private Local Area Network (LAN) of PCs. The other, public side
is the Internet, or the Wide Area Network (WAN), outside of your home or
office.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
If you use the Router to share your cable or DSL Internet connection, contact
your ISP to find out if they have assigned a static IP address to your account.
If so, you will need that static IP address when configuring the Router. You can
get the information from your ISP.
Network Setup Overview
This user guide covers the basic steps for setting up a network with a router.
After going through the appropriate “Getting to Know the Router” chapter
(Chapter 2, 3, or 4, depending on which Router you have), most users will only
need to use the following chapters:
Dynamic IP Addresses
A dynamic IP address is automatically assigned to a device on the network,
such as PCs and print servers. These IP addresses are called “dynamic”
because they are only temporarily assigned to the PC or device. After a certain
time period, they expire and may change. If a PC logs onto the network (or the
Internet) and its dynamic IP address has expired, the DHCP server will assign
it a new dynamic IP address.
• Chapter 5: Connect the Router
This chapter instructs you on how to connect the cable or DSL modem to the
Router and connect the PC(s) to the Router.
• Chapter 7: Configure the PCs
This chapter instructs you on how to configure your PC(s) for a DHCP con-
nection, if the network settings are not already set to DHCP.
For DSL users, many ISPs may require you to log on with a user name and
password to gain access to the Internet. This is a dedicated, high-speed con-
nection type called Point to Point Protocol over Ethernet (PPPoE). PPPoE is
similar to a dial-up connection, but PPPoE does not dial a phone number when
establishing a connection. PPPoE also will provide the Router with a dynamic
IP address to establish a connection to the Internet.
• Chapter 8: Configure the Router
This chapter explains how to configure the Router using your web browser
and the Router’s web-based utility. You will configure the Router using the
settings provided by your ISP.
When you’re finished with the basic steps, then you are ready to connect to the
Internet. After the PC(s) can access the Internet through the Router, you can
alter the Router’s settings further; for example, you can adjust security features
and other settings to enable
online gaming.
DHCP (Dynamic Host Configuration Protocol) Servers
PCs and other network devices using dynamic IP addressing are assigned a new
IP address by a DHCP server. The PC or network device obtaining an IP
address is called the DHCP client. DHCP frees you from having to assign IP
addresses manually every time a new user is added to your network.
Note: To learn about additional security
features, ZoneAlarm Pro and PC-cillin
(each sold separately), see “Chapter 9: The
Cable/DSL Router’s Web-based Utility.”
A DHCP server can either be a designated PC on the network or another net-
work device, such as the Router. By default, the Router’s WAN setting is DHCP
client.
Notebook with Ethernet Adapter
WAN
By default, a DHCP server (LAN side) is enabled on the Router. If you already
have a DHCP server running on your network, you must disable one of the two
DHCP servers. If you run more than one DHCP server on your network, you
will experience network errors, such as conflicting IP addresses. To disable
DHCP on the Router, see the DHCP section in “Chapter 9: The Cable/DSL
Router’s Web-based Utility.”
Cable or DSL
Modem
LAN
Cable/DSL Router
Note: Even if you assign a static IP address to a PC, other PCs can
still use DHCP’s dynamic IP addressing, as long as the static IP
address is not within the DHCP range of the LAN IP Address.
PC with Ethernet Adapter
If the dynamic IP addressing fails to provide a dynamic IP address,
refer to “Appendix A: Troubleshooting.”
Figure 1-4
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
The 4-Port Router’s Front Panel LEDs
Chapter 2: Getting to Know the 4-
®
Port EtherFast Cable/DSL Router
The 4-Port Router’s Rear Panel
The Router’s ports, where network cables are connected, are located on the rear
panel of the Router, as shown in Figure 2-1.
Figure 2-2
Power
Green. The Power LED lights up when the Router is powered
on.
Link/Act
Green. The Link/Act LED serves two purposes. If the LED
is continuously lit, the Router is successfully connected to a
device through the corresponding port (1, 2, 3 or 4). If the
LED is flickering, the Router is actively sending or receiving
data over that port. Port 1 is lit when using the Uplink port.
Figure 2-1
WAN
The WAN (Wide Area Network) port is where you
connect your cable or DSL modem through an
Ethernet cable. Your modem connection will not
work from any other port.
Full/Col
Green. The Full/Col LED also serves two purposes. If this
LED is lit up continuously, the connection made through the
corresponding port is running in Full Duplex mode. If the
LED flickers, the connection is experiencing collisions.
Infrequent collisions are normal.
Ports 1-4
These four LAN (Local Area Network) ports con-
nect to network devices, such as PCs, print servers,
and remote hard drives. If Port 1 is being used, the
Uplink port will not work because these two shared
ports have internally shared wiring.
If this LED flickers too often, there may be a problem with
your connection. See “Appendix A: Troubleshooting” if you
encounter this problem.
Uplink
The Uplink port is used to expand your network by
connecting to another switch or hub. To uplink to a
switch or a hub, simply run a cable from the Uplink
port to the other device. See the “Uplinking:
Connecting More Devices to the Router” section for
more on uplinking.
100
Orange. The 100 LED lights up when a successful 100Mbps
connection is made through the corresponding port.
If this LED does not light up, then your connection speed is
10 Mbps.
If the Uplink port is being used, Port 1 will not
work.
Power
The Power port is where you will connect the
power adapter.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
The WAN Indicators
Chapter 3: Getting to Know the 1-
Link
Green. The Link LED lights up when a successful connec-
tion is made between the Router and your cable or DSL
modem or network.
Port EtherFast Cable/DSL Router
The 1-Port Router’s Rear Panel
Act
Green. The Act LED flickers when the Router is sending or
receiving data over the WAN port (to the Internet).
The rear panel of the Router is where all of the Router’s cabling connections
are made, and where you can reset or configure the Router’s LAN port, as
shown in Figure 3-1.
Diag
Red. The Diag LED lights up when the Router goes through
its self-diagnosis mode during every boot-up. It will turn off
upon successful completion of the diagnosis.
If this LED stays on for an abnormally long period of time,
see “Appendix A: Troubleshooting.”
*
The Reset Button
The Reset button can be used in one of two ways.
Figure 3-1
WAN
LAN
The WAN (Wide Area Network) port is where you
connect your cable or DSL modem through an
Ethernet cable. Your modem connection will not
work from any other port.
1. If the Router is having problems connecting to the Internet, press the Reset
button for just a moment with a paper clip or a pencil tip. This clears up any
jammed connections, and is similar to pressing the Reset button on your PC
to reboot it.
The LAN (Local Area Network) port is where you
connect the Router to a PC, hub, or switch. If you
have more than one PC, connect an Ethernet hub or
switch to the Router, and then connect your PCs to
that hub or switch.
2. If you are experiencing extreme problems with the Router and have tried all
other troubleshooting measures, press the Reset Button and hold it down
until the red Diag LED on the front panel turns on and off completely.
This will restore factory defaults and clear all of the Router’s settings, includ-
ing settings such as IP addresses or a new password.
Power
The Power port is where you will connect the
power adapter.
* The Reset Button is located on the front panel of the 4-Port Router, and the rear panels of the 3-
Port Router and the 1-Port Router.
Buttons & Switches
Proceed to “Chapter 5: Connect the Router.”
The Reset Button
Details on the Reset button are found in the
“Chapter 2: Getting to Know the 4-Port EtherFast
Cable/DSL Router.”
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Full/Col Green. The Full/Col LED also serves two purposes. If this
The Crossover Switch
When “uplinking,” or connecting two pieces of network hardware together,
such as a hub and a switch, a general rule of thumb is to plug one end of a
network cable into a straight-through port, and the other end into a crossover
port (uplink port). Standard ports are straight-through ports, and uplink ports
are crossover ports.
LED remains lit, a LAN port connection is being successful-
ly maintained. If the LED flickers, the connection is experi-
encing collisions. Infrequent collisions are normal.
If this LED flickers too often, there may be a problem with
your connection. See “Appendix A: Troubleshooting” if you
encounter this problem.
The
1
-
Port
10/100
Orange. The 10/100 LED lights up when a successful
100 Mbps connection is made through the corresponding
port.
If a connection is running at 10 Mbps, the 10/100 LED will
not light up.
Figure 3-2
Important: The chart in Figure 3-2 is for reference purposes
only. Every network is different. If you do not make a connec-
tion to a hub or switch by using the settings above, change the
position of the Crossover Switch.
The WAN Indicators
Link
Green. The Link LED lights up when a successful connec-
tion is made between the Router and your broadband device
or network.
The 1-Port Router’s Front Panel LEDs
Act
Green. The Act LED flickers when the Router is sending or
receiving data over the WAN port.
Diag
Red. The Diag LED lights up when the Router goes through
its self-diagnostic mode. It will turn off upon successful
completion of the diagnosis.
If this LED stays on for an abnormally long period of time,
see “Appendix A: Troubleshooting.”
Figure 3-3
Power
Green. The Power LED lights up green when the Router is
powered on.
Proceed to “Chapter 5: Connect the Router.”
Link/Act
Green. The Link/Act LED serves two purposes. If the LED
is continuously lit, the Router is successfully connected to a
device through the LAN port. If the LED is flickering, the
Router is actively sending or receiving data through the LAN
port.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
USB Compatibility
Chapter 4: Getting to Know the 3-
Note: USB ports do not work on PCs running Windows 95 or NT.
Port EtherFast Cable/DSL Router
The 3-Port Router’s Rear Panel
To use the USB port on the 3-Port Router, you must have Windows 98, 2000,
Millennium, or XP installed on your PC. USB cannot run in a Windows 95 or
NT environment.
Also, your PC must have a USB port installed and enabled. Some PCs may
have a disabled USB port. If your port doesn’t seem to be working, there may
be jumpers on the motherboard or a menu option in the BIOS to enable a PC’s
USB port.
Figure 4-1
Other motherboards have USB interfaces, but no ports. You can purchase and
install a USB-ready card at your local computer store. See your PC’s user
guide for instructions.
Ports 1-3
Uplink
These three LAN ports connect to your PCs, hubs,
switches, print servers, or any other devices with an
Ethernet port.
This USB icon, shown in Figure 4-2, denotes the presence of a USB port or
connector.
The Uplink port connects to another hub or switch
for port expansion when you run out of open ports
for your network devices. Since the Uplink port and
the standard port right next to it share internal wiring,
you can only use one of the two ports at a time.
Figure 4-2
WAN
The WAN (Wide Area Network) port is where you
connect your cable or DSL modem through an
Ethernet cable. Your modem connection will not
work from any other port.
The 3-Port Router comes with a USB cable that has two different types of con-
nectors. Type A, the master connector, is shaped like a rectangle and plugs into
your PC’s USB port. Type B, the slave connector, resembles a square and con-
nects to the USB port on the rear panel of the Router.
Power
USB
The Power port is where you will connect the
power adapter.
The USB port (Type B - slave) can connect to a
USB-ready PC or a USB hub. This allows you to
enjoy an immediate, plug-and-play connection with-
out even installing an Ethernet adapter for your PC.
To work with USB ports, your PC must be running
Windows 98, 2000, Millennium, or XP.
USB Type B
USB Type A
Figure 4-3
The Reset Button
Details on the Reset button are found in the
“Chapter 2: Getting to Know the 4-Port EtherFast
Cable/DSL Router.”
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
The WAN Indicators
The 3-Port Router’s Front Panel LEDs
Link
Green. The Link LED lights up when a successful connec-
tion is made between the Router and your broadband device
or network.
Act
Green. The Act LED flickers when the Router is sending or
receiving data over the broadband WAN port.
Diag
Red. The Diag LED lights up when the Router goes through
its self-diagnostic mode. It will turn off upon successful
completion of the diagnosis.
Figure 4-4
Power
Green. The Power LED lights up green when the Router is
powered on.
If this LED stays on for an abnormally long period of time,
see “Appendix A: Troubleshooting.”
Link/Act
Green. The Link/Act LED serves two purposes. If the LED
is continuously lit, the Router is successfully connected to a
device through the corresponding RJ-45 port (1, 2, or 3). If
the LED flickers, then that port is sending or receiving data
to and from the network. When the Uplink port is in use, then
Port 3 will be lit.
Proceed to “Chapter 5: Connect the Router.”
Full/Col
Green. The Full/Col LED also serves two purposes. If this
LED is continuously lit, the connection made through the
corresponding port is running in Full Duplex mode. If the
LED is flickering, the connection is experiencing collisions.
Infrequent collisions are normal.
If this LED flickers too often, there may be a problem with
your connection. See “Appendix A: Troubleshooting” if you
have problems.
100
Orange. The 100 LED lights up when a successful 100 Mbps
connection is made through the corresponding port. If this
LED does not light up, then your connection speed is
10 Mbps.
USB
The USB LED lights up when the USB port is successfully
connected to a USB-ready PC or USB hub.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Connecting Your Hardware Together and Booting Up
Chapter 5: Connect the Router
1. Before you begin, make sure that all of your hardware is powered off, includ-
ing the Router, PCs, hubs, switches, and cable or DSL modem.
Overview
Unlike a hub or a switch, the Cable/DSL Router’s setup consists of more than
simply plugging hardware together. You will have to configure your networked
PCs to accept the IP addresses that the Router assigns them (if applicable), and
you will also have to configure the Router with setting(s) provided by your
Internet Service Provider (ISP).
2. If you have the 4-Port Router, go to step 2.A. If you have the 1-Port Router,
go to step 2.B. If you have the 3-Port Router, go to step 2.C.
2. A. If you have the 4-Port Cable/DSL Router, connect one end of an
Ethernet cable to one of the LAN ports (labeled 1, 2, 3, or 4) on the back of
the Router, and the other end to a standard port on a network device, e.g., a
PC, print server, hub, or switch. See “Appendix E: Twisted-Pair Cabling” for
details on network cabling.
The installation technician from your ISP should have left the setup informa-
tion with you after installing your broadband connection. If not, you can call
your ISP to request the data.
Note: A standard port is any port other than the WAN port and
the Uplink port on the Router. It is a straight-through port.
Once you have the setup information you need for your specific type of Internet
connection, you can begin installation and setup of the Router.
Repeat the above step to connect more PCs or network devices to the Router.
2. B. If you have the 1-Port Router, connect one end of an Ethernet cable to
the LAN port on the back of the Router, and the other end to a port on a net-
work device, e.g., a PC, hub, or switch. If you are using the LAN Port to con-
nect to a PC, set the Crossover switch to straight-through mode ( || ). If you
are connecting the Router to a hub or switch, refer to the chart shown in
Figure 5-2 when setting the Crossover switch.
AN
Figure 5-2
Figure 5-1
2. C. If you have the 3-Port Cable/DSL Router, connect one end of an
Ethernet cable from the Router’s LAN ports (labeled 1, 2, or 3) to an
Ethernet adapter port on a PC, hub, switch, or other network device.
The 3-Port Router features one USB plug-and-play port that connects
instantly to any USB-ready PC or USB hub. This allows you to connect to
and access the Router without even installing any Ethernet adapter cards.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
3. Connect the Ethernet cable from your cable or DSL modem to the WAN port
on the Router’s rear panel. This is the only port that will work for your
modem connection.
Uplinking: Connecting More Devices to the Router
If the Router’s LAN ports are all full and you still have PCs and/or devices to
connect, connect a hub or a switch to the Router using an Ethernet cable.
4. Connect the power adapter to the Power port on the rear panel of the Router,
and then plug the power adapter into a power outlet.
To do so, use the Router’s Uplink port to connect to a standard port on a hub
or switch. This leaves you with new, open ports on the hub or switch, to which
you can add more PCs and/or network devices.
Note: You should always plug the Router’s power
adapter into a surge protecting power strip.
If you have a PC/device connected to the port right next to the Uplink port (on
the 3- and 4-Port Routers), disconnect that PC/device and plug it into an open
port on the new hub or switch.
• The Power LED on the front panel will light up green as soon as the power
adapter is connected properly.
• The Diag LED will light up red for a few seconds when the Router goes
through its self-diagnostic test. This LED will turn off when the self-test is
complete.
Since the Uplink port shares internal wiring with the port right next to it, you
can only use one of these two ports at a time; these ports are called shared
ports.
5. Power on the cable or DSL modem.
If your new hub or switch also has an Uplink port, it too can be uplinked when
you run out of ports, and so on.
6. Press the Reset button on the Router’s front panel with a paper clip or a pen-
cil. Hold the button in until the Diag LED lights up and then turns off. This
will restore the Router’s factory default settings.
uct lines of 10/100 Mbps hubs and switches.
Have you checked that the Link/Act LEDs for all your LAN con-
nections and the Link LED for your WAN connection light up?
If you have a 3-Port Router with USB and you are using its USB port,
then proceed to the next page, “Chapter 6: Installing the BEFSRU31’s
USB Port Drivers.” Otherwise, go to “Chapter 7: Configure
the PCs.”
If all of your Link LEDs are not lighting up, make sure that all your
cables are securely plugged in, and that all of your hardware is powered
on properly. Verify that the modem is plugged into the WAN port on the
Router.
The Router’s hardware installation is now complete.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
3. Select Search for the best driver for your device (Recommended), shown
in Figure 6-2. Click the Next button.
Chapter 6: Installing the
BEFSRU31’s USB Port Drivers
Use the enclosed USB cable to connect your PC to the Router; the Type A end
connects to your PC’s USB port, while the Type B end connects to the Router’s
USB port. Now that all of the Router’s hardware is connected together, you
must enable the PC that will connect to the Router through its USB port.
Since your USB connection acts as an Ethernet adapter for your PC, there’s no
need for you to install an Ethernet adapter on that PC. Just follow the direc-
tions below to enable your PC’s USB connection to the Router:
• If you are running Windows 98, continue to the section below on this page.
• For other Windows operating systems, please refer to the appropriate section
in this chapter as listed in the Table of Contents.
Figure 6-2
Note: After you finish this configuration, make sure that TCP/IP is
installed on your PC(s). For instructions on installing TCP/IP, see
“Appendix D: Installing the TCP/IP Protocol.”
4. Insert the driver disk into the floppy drive, and select Floppy disk drives
only, as shown in Figure 6-3. Click the Next button to start the search for
your driver.
You can also connect the Router’s USB port to other USB devices besides
USB-ready PCs, such as a USB hub using a USB cable.
Installing the Windows 98 Driver
1. With the Router powered up and connected to your PC’s USB port using a
USB cable, start up your PC in Windows 98, and have the Router’s driver
disk available.
2. Windows will notify you that it has detected new hardware, as shown in
Figure 6-1. Click the Next button.
Figure 6-3
Figure 6-1
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
5. The Hardware Wizard will search the floppy, and a new window will appear
(shown in Figure 6-4), notifying you that Windows is now ready to install the
best driver for this device. Click the Next button to continue.
7. Windows will notify you that it has completed copying the driver files to
your PC, as shown in Figure 6-6. Click the Finish button to complete the
USB driver installation.
Figure 6-4
Figure 6-6
6. Windows will begin copying the files to your PC, as shown in Figure 6-5.
Do not click the Cancel button or press the Esc key during this process.
8. Windows will ask you if you want to restart your PC, as shown in Figure 6-
7. Click the Yes button so your new installation will take effect.
If Windows asks for your Windows operating system files before copying,
direct your PC to the location of those files, e.g, c:\windows\options\cabs,
or D:\Win98 (if “D” is the letter of your CD-ROM drive).
Figure 6-7
If it does not ask you to restart your computer, click the Start button, and
select Shut Down. Then select Restart and click the OK button.
Figure 6-5
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
9. When your PC has finished restarting, click the Start button, and select
Settings and Control Panel. Double-click Network. Make sure that
TCP/IP is installed on your PC, as shown on the screen in Figure 6-8. By
default, Windows 98 has TCP/IP installed. If TCP/IP is not installed, please
go to “Appendix D: Installing the TCP/IP Protocol” for installation instruc-
tions.
Installing the Windows 2000 Driver
1. With the Router powered up and connected to your PC’s USB port using a
USB cable, start up your PC in Windows 2000, and have the Router’s driver
disk available. Windows will notify you that the PC has found new hardware.
The Windows’ Hardware Wizard will then notify you that it is ready to start
installing the driver files on your PC, as shown in Figure 6-9. Click the Next
button.
Figure 6-9
2. Select Search for a suitable driver for my device (Recommended), as
shown in Figure 6-10, and click the Next button.
Figure 6-8
Your USB driver installation is now complete.
Go to “Chapter 7: Configure the PCs.”
Figure 6-10
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
3. Insert the driver disk into the floppy drive, and when Windows asks you
where to search for driver files, select Floppy disk drives only, as shown in
Figure 6-11. Click the Next button.
5. When the Digital Signature Not Found screen appears, as shown in Figure 6-
13, Windows will ask you if you want to continue the installation. Click the
Yes button.
Figure 6-11
Figure 6-13
4. Windows will notify you that it has found the driver files. (See Figure 6-12.)
6. Click the Next button from the screen shown in Figure 6-14 to allow
Click the Next button.
Windows to copy the driver files to your PC.
Figure 6-12
Figure 6-14
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
7. Windows will notify you that it has finished installing the driver files on
your PC, as shown in Figure 6-15. Click the Finish button to complete the
USB driver installation.
Installing the Windows Millennium Driver
1. With the Router powered up and connected to your PC’s USB port using a
USB cable, start up your PC in Windows Millennium.
Figure 6-17
2. Windows will notify you that new hardware has been detected (see Figure
6-17). Insert the driver disk. Select Automatic search for a better drive
(Recommended), and click the Next button (see Figure 6-18).
Figure 6-15
8. Go to the Start button, and select the Settings option. Then select the
Network and Dial-up Connections option, and click the Local Area
Connection icon. Click the Properties button to display the screen shown
in Figure 6-16. Highlight Internet Protocol (TCP/IP), as shown in Figure
6-16, and click the Properties button. Make sure that TCP/IP is set to
Obtain an IP address automatically.
Figure 6-18
3. Windows will notify you that it has finished installing the driver files on
your PC, as shown in Figure 6-19. Click the Finish button.
Figure 6-16
Your USB driver installation is now complete.
Go to “Chapter 7: Configure the PCs.”
Figure 6-19
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
4. Windows will ask you to restart your PC, as shown in Figure 6-20. Click the
Yes button.
Installing the Windows XP Driver
1. With the Router connected to your PC’s USB port using a USB cable, start
up your PC in Windows XP.
Figure 6-22
Figure 6-20
2. Windows will notify you that new hardware has been detected (shown in
Figure 6-22). Select Install from a list or specific location (Advanced),
and click the Next button (see Figure 6-23).
5. When your PC has finished restarting, click the Start button, and select
Settings and Control Panel. Double-click Network and you will see a
screen similar to that shown in Figure 6-21. Make sure that TCP/IP is
installed for your PC, as shown in Figure 6-21. By default, Windows
Millennium has TCP/IP installed. If TCP/IP is not installed, please go to
“Appendix D: Installing the TCP/IP Protocol” for instructions on installa-
tion.
Figure 6-23
3. Insert the driver disk into the floppy drive, and select Search for the best
driver in these locations. Then select Include this location in the search:
and enter A:\ in the location field (if “A” is the letter of your floppy drive).
(See Figure 6-24.) All other options must be unchecked (assuming you are
running Windows XP with the default interface). Click the Next button.
Figure 6-21
Your USB driver installation is now complete.
Go to “Chapter 7: Configure the PCs.”
Figure 6-24
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
4. When the Hardware Installation screen appears shown in Figure 6-25, click
Continue Anyway.
Chapter 7: Configure the PCs
Overview
The instructions in this chapter will help you configure each of your comput-
ers to be able to communicate with the Router.
To do this, you need to configure your PC’s network settings to obtain an IP (or
TCP/IP) address automatically (called DHCP). Computers use IP addresses to
communicate with each other across a network or the Internet.
Find out which operating system your computer is running, such as Windows
95, 98, Millennium, NT 4.0, 2000, or XP. You will need to know which oper-
ating system your computer is running. You can find out by clicking the Start
button and then going to the Settings option. Then click Control Panel, and
then double-click the System icon. If your Start menu doesn’t have a Settings
option, you’re running Windows XP. Click the Cancel button when done.
Figure 6-25
5. Windows will notify you that it has finished installing the driver files on
your PC, as shown in Figure 6-26. Click the Finish button to complete the
USB driver installation.
You may need to do this for each computer you are connecting to the Router.
Important: These instructions apply only to Windows 95,
Windows 98, Windows Millennium, Windows 2000, or Windows
XP machines. For TCP/IP setup under Windows NT, see your
Windows manual. By default Windows 98, 2000, Me, and XP has
TCP/IP installed and set to obtain an IP address automatically.
The next few pages tell you, step by step, how to configure your network set-
tings based on the type of Windows operating system you are using. Make sure
that an Ethernet card or adapter has been successfully installed in each PC you
will configure (the only exception is the PC you connect to the 3-Port Router
using the USB port and cable). Once you’ve configured your computers, con-
tinue to “Chapter 8: Configure the Router.”
Figure 6-26
6. Click the Start button and then Control Panel. Click Network and Internet
Connections and then Network Connections. Double-click Local Area
Connection. Click Properties. Check for Internet Protocol (TCP/IP) to
make sure that TCP/IP is installed on your PC. By default, Windows XP has
TCP/IP installed. If TCP/IP is not installed, please refer to your Windows XP
user guide to install TCP/IP.
Your USB driver installation is now complete.
Go to “Chapter 7: Configure the PCs.”
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
Configuring Windows 95, 98, and Millennium PCs
EtherFast® Cable/DSL Routers
3. Click the IP Address tab and select Obtain an IP address automatically,
as shown in Figure 7-2.
1. Go to the Network screen by clicking the Start button. Click Settings and
then Control Panel. From there, double-click the Network icon.
2. On the Configuration tab, select the TCP/IP line for the applicable
Ethernet adapter, as shown in Figure 7-1. Do not choose a TCP/IP entry
whose name mentions DUN, PPPoE, VPN, or AOL. If the word TCP/IP
appears by itself, select that line. (If there is no TCP/IP line listed, refer to
“Appendix D: Installing the TCP/IP Protocol” or your Ethernet adapter’s
user guide to install TCP/IP now.) Click the Properties button.
Figure 7-2
4. Now click the Gateway tab to ensure that the Installed Gateway field is left
blank. Click the OK button.
5. Click the OK button again. Windows may ask you for the original
Windows installation disk or additional files. Supply them by pointing to
the
correct
file
location,
e.g.,
D:\win98,
D:\win9x,
c:\windows\options\cabs, etc. (if “D” is the letter of your CD-ROM drive).
6. Windows may ask you to restart your PC. Click the Yes button. If Windows
Figure 7-1
does not ask you to restart, restart your computer anyway.
Go to “Chapter 8: Configure the Router.”
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
4. Select Internet Protocol (TCP/IP), as shown in Figure 7-4, and click the
Configuring Windows 2000 PCs
Properties button.
1. Go to the Network screen by clicking the Start button. Click Settings and
then Control Panel. From there, double-click the Network and Dial-up
Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter
(usually it is the first Local Area Connection listed). Do not choose a
TCP/IP entry whose name mentions DUN, PPPoE, VPN, or AOL. Double-
click the Local Area Connection.
Figure 7-4
5. Select Obtain an IP address automatically, as shown in Figure 7-5. Once
the new window appears, click the OK button. Click the OK button again
to complete the PC configuration.
Figure 7-3
3. The Local Area Connection Status screen will appear, as shown in Figure 7-
3. Click the Properties button.
Figure 7-5
6. Restart your computer.
Go to “Chapter 8: Configure the Router.”
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
4. Select Internet Protocol (TCP/IP), as shown in Figure 7-7, and click the
Configuring Windows XP PCs
Properties button.
The following instructions assume you are running Windows XP with the
default interface. If you are using the Classic interface (where the icons and
menus look like previous Windows versions), please follow the instructions for
Windows 2000.
1. Click to the Network screen by clicking the Start button and then Control
Panel. From there, click the Network and Internet Connections icon and
then the Network Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter
(usually it is the first Local Area Connection listed). Double-click the
Local Area Connection.
Figure 7-7
5. Select Obtain an IP address automatically, as shown in Figure 7-8. Once
the new window appears, click the OK button. Click the OK button again
(or the Close button if any settings were changed) to complete the PC con-
figuration.
Figure 7-8
Figure 7-6
3. The Local Area Connection Status screen will appear, as shown in Figure 7-
6. Restart your computer.
6. Click the Properties button.
Go to “Chapter 8: Configure the Router.”
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
3. The Router configuration screen will appear with the Setup tab selected.
Based on the setup instructions from your ISP, you may need to provide the
following information.
Chapter 8: Configure the Router
This chapter will show you how to configure the Router to function in your net-
work and gain access to the Internet through your Internet Service Provider
(ISP). Detailed description of the Router’s Web-based Utility can be found in
“Chapter 9: The Cable/DSL Router’s Web-based Utility.” Your ISP may require
the use of a Host Name and Domain Name. Further, you will set the WAN
Connection Type on the Router’s Setup tab based on the information provided
by your ISP. You will need the setup information from your ISP. If you do not
have this information, please contact your ISP before proceeding.
Host Name and Domain Name: These fields allow you to provide a host
name and domain name for the Router. These fields are usually left blank.
If requested by your ISP (usually cable ISPs), complete these two fields.
Device IP Address and Subnet Mask: The values for the Router’s IP
Address and Subnet Mask are shown on the Setup screen. The default value
is 192.168.1.1 for the IP Address and 255.255.255.0 for the Subnet Mask.
Leave these settings alone.
The instructions from your ISP tell you how to set up your PC for Internet
access. Because you are now using the Router to share Internet access among
several computers, you will use the setup information to configure the Router
instead of your PC. You only need to configure the Router once using the first
computer you set up.
4. The Router supports five connection types: DHCP (obtain an IP automati-
cally), PPPoE, Static IP Address, RAS, and PPTP. These types are listed in
the drop-down menu for the WAN Connection Type setting. Each Setup
screen and available features will differ depending on what kind of connec-
tion type you select. Proceed to the instructions for the connection type you
are using. When you are finished with the Setup tab, proceed to step 5.
1. Open your web browser. (It is all right if you get an error message at this
web browser’s Address field,
IMPORTANT: If you have previously enabled any Internet-sharing
proxy server software on any of your PCs, you must disable it now.
as shown in Figure 8-1, and
press the Enter key.
Some examples of Internet-sharing software are Internet LanBridge,
Wingate, ICS, and Sygate. To disable your Internet-sharing software:
Figure 8-1
2. An Enter Network Password window, shown in Figure 8-2, will appear
(Windows XP users will see a Connect to 192.168.1.1 window, shown in
Figure 8-3). Leave the User Name field empty, and enter admin in lower-
case letters in the Password field (admin is the default password). Then,
click the OK button.
• If you are running Netscape Navigator, click Edit >> Preferences
>> Advanced >> Proxies. Click Direct Connection to the
Internet.
• If you are running Internet Explorer 5.x or higher, click Start >>
Settings >> Control Panel >> Internet Options >> Connections
>> LAN Settings. Remove checkmarks from all three boxes. Click
the OK button to continue.
Also, you must disable any Internet log-on software (such as Ivasion
Winpoet or Enternet 300) and any firewall software (such as
ZoneAlarm and Watchdog) on all of your PCs.
Figure 8-2
Figure 8-3
42
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
DHCP or Obtain an IP Address Automatically
PPPoE
If your ISP says that you are
connecting through DHCP
or a dynamic IP address
from your ISP, perform
these steps:
If your DSL provider says
that you are connecting
through PPPoE or if you
normally enter a user name
and password to access the
Internet, perform these
steps:
A. Select Obtain an IP
automatically as the
WAN Connection Type,
as shown in Figure 8-4.
A. Select PPPoE as the
WAN Connection Type,
as shown in Figure 8-6.
Figure 8-4
B. Click the Apply button
Figure 8-6
to save the setting., or click the Cancel button to clear the setting and start
B. Enter the User Name.
over. When you are finished, then proceed to step 5.
C. Enter the Password.
Static IP Address or Specify an IP Address
D. Click the Apply button to save the settings., or click the Cancel button to clear
the settings and start over.
If your ISP says that you are
connecting through a static or
fixed IP address from your ISP,
perform these steps:
E. When you are finished, click the Status tab, and then click the Connect
button to start the connection. Proceed to step 5.
RAS
A. Select Static IP as the WAN
Connection Type, as shown
in Figure 8-5.
RAS (shown in Figure 8-7) is
a service used in Singapore
only. If you are using a RAS
connection, check with your
ISP for the necessary setup
information.
B. Enter the IP Address.
C. Enter the Subnet Mask.
D. Enter the Gateway Address.
When you are finished with
the Setup tab, proceed to step
5.
Figure 8-5
E. Enter the DNS in the 1, 2, and/or 3 fields. You need to enter at least one
DNS address.
F. Click the Apply button to save the settings, or click the Cancel button to
Figure 8-7
clear the settings and start over. When you are finished, then proceed to step
5.
44
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
PPTP
Chapter 9: The Cable/DSL Router’s
Web-based Utility
Overview
PPTP (shown in Figure 8-8) is
a service used in Europe only.
If you are using a PPTP con-
nection, check with your ISP
for the necessary setup infor-
mation.
For your convenience, use the Router’s web-based utility to administer it. This
chapter will explain all of the functions in this utility. The utility can be
accessed via Microsoft Internet Explorer or Netscape Navigator through use of
a computer connected with an Ethernet cable to the Router (or a computer con-
nected with a USB cable to the USB port of the 3-Port Router).
When you are finished with
the Setup tab, proceed to step
5.
For a basic network setup, most users only have to use the following screens of
the utility:
Figure 8-8
5. If you haven’t already done so, click the Apply button to save your Setup
• Setup Enter the settings provided by your ISP.
settings. Close the web browser.
• Password The Router’s default password is admin. To secure the Router,
change the Password from its default.
6. Reset the power on your cable or DSL modem.
7. Restart your computers so that they can obtain the Router’s new settings.
The Status, DHCP, Log, Security, and Help tabs are also available for basic
setup of the Router. For advanced setup of the Router, click the Advanced tab
to access these screens: IP Filtering, Port Range Forwarding, Dynamic Routing,
Static Routing, DMZ Host, and MAC Address Clone.
If you need advanced setting information, please refer to “Chapter 9: The
Cable/DSL Router’s Web-based Utility” or the Linksys support website at
support.linksys.com.
Quick and Easy Router Administration
Congratulations! You’ve successfully configured the Router. Test the setup
by opening your web browser from any computer and entering
www.linksys.com/registration, as shown in Figure 8-9.
To access the web-based utility of the Router, launch Internet Explorer or
Netscape Navigator, and enter the Router’s default IP address, 192.168.1.1, in
the Address field, as shown in Figure 9-1, and press Enter.
If you are unable to reach our
website, you may want to
review what you did in this
section or refer to “Appendix
A: Troubleshooting.”
Figure 8-9
Figure 9-1
Proceed to “Chapter 9: The Cable/DSL Router’s Web-based Utility” for
more details and advanced settings information.
46
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
A password request page, shown in Figure 9-2 will pop up. (Windows XP users
will see a Connect to 192.168.1.1 window, shown in Figure 9-3). Leave the
User Name field blank, and enter admin in the Password field. Then click the
OK button. Router Administration
• Device IP Address and Subnet Mask The values for the Router’s IP
Address and Subnet Mask are shown here. The default values are
192.168.1.1 for the Device IP Address and 255.255.255.0 for the Subnet
Mask.
• WAN Connection Type The Router supports five connection types: DHCP,
PPPoE, Static IP, PPTP, and RAS. Each Setup screen and available features
will differ depending on what kind of connection type you select.
Note: You can test and see if the settings are correct by successfully
connecting to the Internet.
DHCP
Figure 9-2
Figure 9-3
In this section, you’ll find brief descriptions of each web page in the Utility and
each page’s key functions.
To apply any of the settings you change on a page, click the Apply button. To
cancel any values you’ve entered on any page, click the Cancel button.
Setup
The Setup screen is the first screen you see when you access the web-based
utility. If you have already installed and set up the Router, you have already
seen this screen and properly configured all of the screen’s values.
• Host Name & Domain Name These fields allow you to supply a host and
domain name for the Router. Some ISPs require these names as identifica-
tion. You may have to check with your ISP to see if your broadband Internet
service has been configured with a host and domain name. In most cases,
leaving these fields blank will work.
Figure 9-4
By default, the Router’s WAN Connection Type is set to Obtain an IP auto-
matically, as shown in Figure 9-4, and it should be used only if your ISP
supports DHCP.
• Firmware Version This entry shows the version and date of the firmware
you are using. Future versions of the Router’s firmware will be posted and
To apply any of the settings you change on a page, click the Apply button.
To cancel any values you’ve entered on any page, click the Cancel button.
Continue to the “Password” section.
48
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
PPPoE
Static IP
Some DSL-based
ISPs use PPPoE
(Point-to-Point
Protocol
over
Ethernet) to estab-
lish Internet con-
nections for end-
users. If you are
connected to the
Internet through a
DSL line, check
with your ISP to
see if they use
PPPoE. If they do,
you will have to
enable it, as shown in Figure 9-5.
Figure 9-5
User Name and Password Enter the User Name and Password provided
by your ISP.
Figure 9-6
Connect on Demand and Max Idle Time You can configure the Router to
cut your connection with your ISP after a specified period of time (Max Idle
Time). If you have been disconnected due to inactivity, Connect on Demand
enables the Router to automatically re-establish your connection as soon as
you attempt to access the Internet again. If you wish to activate Connect on
Demand, click the radio button. If you want your Internet connection to
remain on at all times, enter 0 in the Max Idle Time field. Otherwise, enter
the number of minutes you want to have elapsed before your Internet access
disconnects.
If you are required to use a permanent IP address, then select Static IP, as
shown in Figure 9-6.
Specify WAN IP Address This is the IP address that the Router has, when
seen from the WAN, or the Internet. Your ISP will provide you with the IP
Address you need to specify here.
Subnet Mask This is the Router’s Subnet Mask, as seen by external users
on the Internet (including your ISP). Your ISP will provide you with the
Subnet Mask.
Keep Alive Option and Redial Period This option keeps your PPPoE-
enabled Internet access connected indefinitely, even when it sits idle. To
use this option, click the radio button next to Keep Alive. The default Redial
Period is 30 seconds.
Default Gateway Address Your ISP will provide you with the Default
Gateway Address.
Important: For DSL users, if you need to enable PPPoE support,
choose PPPoE. If you do enable PPPoE, remember to remove any
PPPoE applications that are already installed on any of your PCs.
DNS (Required) Your ISP will provide you with at least one DNS (Domain
Name System) Server IP Address.
To apply any of the settings you change on a page, click the Apply button.
To cancel any values you’ve entered on any page, click the Cancel button.
Continue to the “Password” section.
To apply any of the settings you change on a page, click the Apply button.
To cancel any values you’ve entered on any page, click the Cancel button.
Continue to the “Password” section.
50
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
PPTP
RAS
Point to Point
Tunneling Protocol
(PPTP) (shown in
Figure 9-7) is a
service that applies
to connections in
Europe only.
R e m o t e
A c c e s s
Service (RAS)
(shown
in
Figure 9-8) is
a service that
applies to con-
nections
in
Specify WAN IP
Address This is the
IP address that the
Router has, when
seen from the
WAN, or the
Internet. Your ISP
will provide you
with the IP Address
you need to specify
here.
S i n g a p o r e
only. For users
in Singapore,
check
Singtel
with
for
information on
RAS.
Figure 9-8
Figure 9-7
User Name and Password Enter the User Name and Password supplied
by Singtel.
Subnet Mask This is the Router’s Subnet Mask, as seen by external users
on the Internet (including your ISP). Your ISP will provide you with the
Subnet Mask.
RAS Plan Select the type of plan you have.
Default Gateway Address Your ISP will provide you with the Default
Gateway Address.
Connect on Demand and Max Idle Time You can configure the Router to
cut your connection with your ISP after a specified period of time (Max Idle
Time). If you have been disconnected due to inactivity, Connect on Demand
enables the Router to automatically re-establish your connection as soon as
you attempt to access the Internet again. If you wish to activate Connect on
Demand, click the radio button. If you want your Internet connection to
remain on at all times, enter 0 in the Max Idle Time field. Otherwise, enter
the number of minutes you want to have elapsed before your Internet access
disconnects.
Connect on Demand and Max Idle Time You can configure the Router to
cut your connection with your ISP after a specified period of time (Max Idle
Time). If you have been disconnected due to inactivity, Connect on Demand
enables the Router to automatically re-establish your connection as soon as
you attempt to access the Internet again. If you wish to activate Connect on
Demand, click the radio button. If you want your Internet connection to
remain on at all times, enter 0 in the Max Idle Time field. Otherwise, enter
the number of minutes you want to have elapsed before your Internet access
disconnects.
Keep Alive Option and Redial Period This option keeps your PPPoE-
enabled Internet access connected indefinitely, even when it sits idle. To
use this option, click the radio button next to Keep Alive. The default Redial
Period is 30 seconds.
Keep Alive Option and Redial Period This option keeps your PPPoE-
enabled Internet access connected indefinitely, even when it sits idle. To
use this option, click the radio button next to Keep Alive. The default Redial
Period is 30 seconds.
To apply any of the settings you change on a page, click the Apply button.
To cancel any values you’ve entered on any page, click the Cancel button.
Continue to the “Password” section.
To apply any of the settings you change on a page, click the Apply button.
To cancel any values you’ve entered on any page, click the Cancel button.
Continue to the “Password” section.
52
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Password
Status
Figure 9-9
Figure 9-10
You should always have a password set for the Router. This is done through the
Password tab, shown in Figure 9-9. The default password is admin.
Note: The information provided and buttons available may
vary depending on the Router’s settings.
If you don’t change the password, all users on your network will be able to
The Status tab, shown in Figure 9-10, displays the Router’s status; it reflects the
data and selections you’ve entered using the Setup screen.
access the Router using the default password admin.
Universal Plug and Play (UPnP) allows Windows XP to automatically config-
ure the Router for various Internet applications, such as gaming and videocon-
ferencing. Click the radio button next to Enable to enable UPnP Services, or
Disable to disable UPnP Services.
All of the information provided on this screen is read-only. To make changes,
select the Setup tab.
• Host Name This field shows the name of the Router. This entry is neces-
sary for some ISPs.
If you select the Restore Factory Default option and click the Apply button,
• Firmware Version This field shows the installed version and date of the
you will clear all of the Router’s settings.
firmware. Version dates are slightly more accurate than version numbers.
Do not restore the factory defaults unless you are having difficulties with the
Router and have exhausted all other troubleshooting measures. Once the Router
is reset, you will have to re-enter all of your configuration data.
• Login This indicates if you are using a dial-up style connection like PPPoE,
RAS, or PPTP. For PPPoE, RAS, or PPTP only, there is a Connect button
to click if you are disconnected and want to re-establish a connection.
• LAN These fields display the current IP Address and Subnet Mask of the
To apply any of the settings you change on a page, click the Apply button. To
Router, as seen by users on your local area network. The DHCP Server field
cancel any values you’ve entered on any page, click the Cancel button.
54
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
shows the status of the Router’s DHCP server function, which is either
enabled or disabled.
• DHCP Server DHCP is already enabled by factory default. If you already
have a DHCP server on your network, set the Router’s DHCP option to
Disable. Click the Apply button. If you disable DHCP, remember to assign
a static IP address to the Router.
• WAN These fields display the WAN IP Address, WAN Subnet Mask, and
WAN Default Gateway IP Address of the Router, as seen by external users
on the Internet. The DNS (Domain Name System) IP Address fields show
the IP address(es) of the DNS currently used by the Router. Multiple DNS
IP settings are common. In most cases, the first available DNS entry is
used.
• Starting IP Address Enter a value for the DHCP server to start with when
issuing IP addresses. This value must be 192.168.1. 2 or greater, because
the default IP address for the Router is 192.168.1.1.
• DHCP Release Click the DHCP Release button to release the current IP
address of the device connected to the Router’s WAN port.
• DHCP Renew Click the DHCP Renew button to replace the current IP
address—of the device connected to the Router’s WAN port—with a new IP
address.
• Number of DHCP Users (Optional) Enter the maximum number of PCs
that you want the DHCP server to assign IP addresses to. This number can-
not be greater than 253. In order to determine the DHCP IP Address range,
add the starting IP address (e.g., 100) to the number of DHCP users. By
default, as shown in Figure 9-11, add 100 to 50, and the range is
192.168.1.100 to 192.168.1.149.
• DHCP Clients Table Click the DHCP Clients Table button to view the list
of PCs that were given IP addresses by the Router.
• Client Lease Time The Client Lease Time is the amount of time a network
user will be allowed connection to the Router with their current dynamic IP
address. Enter the amount of time, in minutes, that the user will be “leased”
this dynamic IP address.
C
DHCP
• DNS The Domain Name System (DNS) is how the Internet translates
domain or website names into Internet addresses or URLs. Your ISP will
provide you with at least one DNS Server IP Address. If you wish to use
another, type that IP Address in one of these fields.You can type up to three
DNS Server IP Addresses here. The Router will use these for quicker access
to functioning DNS servers.
• WINS The Windows Internet Naming Service (WINS) manages each PC’s
interaction with the Internet. If you use a WINS server, enter that server’s
IP Address here. Otherwise, left this blank.
• DHCP Clients Table Click the DHCP Clients Table button to show the
current DHCP Client data. (This data is stored in temporary memory and
changes periodically.)
Figure 9-11
To apply any of the settings you change on a page, click the Apply button. To
cancel any values you’ve entered on any page, click the Cancel button.
A Dynamic Host Configuration Protocol (DHCP) server automatically assigns
an IP address to each PC on your network for you. Unless you already have one,
it is highly recommended that you leave the Router enabled as a DHCP server.
56
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Security
Log
Figure 9-12
The Log tab, shown in Figure 9-12, provides you with a log of all incoming and
outgoing URLs or IP addresses for your Internet connection.
Figure 9-13
The Security tab, shown in Figure 9-13, enables configuration of the Router to
provide enhanced network security using ZoneAlarm Pro and PC-cillin (each
sold separately). The Router provides a built-in Internet NAT firewall.
ZoneAlarm Pro enhances the Router’s security capabilities for increased pro-
tection against hackers and other threats from the Internet. PC-cillin protects
against viruses. ZoneAlarm Pro and PC-cillin work independently of each
other. For more information on ZoneAlarm Pro, PC-cillin, and DSL or cable
network security, please click the on-screen link to the Internet Security Center.
To access activity logs, select the Enable option next to Access Log. This func-
tion can be disabled by clicking the Disable radio button.
With logging enabled, you can choose to view temporary logs or have a per-
manent record, using the Logviewer software. Temporary logs can be accessed
from the Log screen by clicking either the Incoming Access Log or Outgoing
Access Log button. The Incoming Access Log gives you a log of all the incom-
ing Internet traffic while the Outgoing Access Log lists all the URLs and IP
addresses of Internet sites that users on your network have accessed.
Software Download
Click this button to purchase and download ZoneAlarm Pro and/or PC-cillin at
the Internet Security Center. Print the summary page, which contains the
license key needed for installation, or write down the license key if you are
unable to print the page. You will also be e-mailed a confirmation invoice with
the key included. When adding security enhancements to your other networked
computers, you can either copy the downloaded files to the other PCs or re-
download the software on each individual PC without incurring any more costs.
For a permanent record of these logs, Logviewer software must be used. This
Logviewer saves all incoming and outgoing activity as a permanent file on your
PC’s hard drive. In the Send Log to field, enter the fixed IP address of the PC
running the Logviewer software. The Router will now send updated logs to that
PC.
ZoneAlarm Pro Settings
To clear any values you’ve entered on any page, click Cancel and re-enter
information. To apply any settings you’ve altered on any page, click the Apply
button.
If you have downloaded ZoneAlarm Pro, complete this section.
License Key Enter the License Key for ZoneAlarm Pro. The License Key
will be e-mailed to you after you purchase ZoneAlarm Pro.
58
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Enforce ZoneAlarm Pro Security Check this box to enable ZoneAlarm
Pro on the Router. This will require every PC to have ZoneAlarm Pro
installed before being allowed to access the Internet (except for exempt
computers).
Help
Enforcement Level This sets how often ZoneAlarm Pro will check for
unauthorized intrusions. More Secure (default setting) enables ZoneAlarm
Pro to check frequently. Conserve Bandwidth enables ZoneAlarm Pro to
check less frequently; this uses less bandwidth. It is recommended to set
the Enforcement Level at the More Secure setting unless there is a decrease
in the Router’s performance.
PC-cillin Settings
If you have downloaded PC-cillin, complete this section.
Enforce PC-cillin Anti-Virus Check this box to enable PC-cillin Anti-
Virus on the Router.
Exempt Computers
Figure 9-14
If you wish to exempt any computers from enforcement of ZoneAlarm Pro
and/or PC-cillin, complete this section.
Under the Help tab, shown in Figure 9-14, you’ll find links to all of the Utility’s
internal support documentation, including the application that upgrades the
Router’s firmware.
Enable/Disable To enable or disable computer exemptions, click Enable
or Disable.
for free. If the Router can access the Internet already, there’s no need to down-
load a newer firmware version, unless that version has a new feature that you
want to use. Loading new firmware onto the Router does not enhance the
speed or the quality of your connection speed.
From IP Address/To IP Address Enter the range of IP addresses for the
computers you want to exempt from enforcement of ZoneAlarm Pro and/or
PC-cillin.
AOL Parental Controls
See the “IP Filtering” section for directions on how to enable remote firmware
upgrades.
Enabling this engages AOL’s proprietary “Parental Control” feature. Enabling
this will disable all options under the Advanced tab except MAC Address
cloning.
Note: AOL Parental Controls are available
to AOL customers in the Unites States Only.
To apply any of the settings you change on a page, click the Apply button. To
cancel any values you’ve entered on any page, click the Cancel button.
60
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
To upgrade the Router’s firmware:
IP Filtering
Note: By upgrading the Router’s firmware, you may lose the Router’s
configuration settings.
IP filters block specific inter-
nal users from accessing the
Internet and enable Virtual
Private Network (VPN) ses-
sions. You can set up filters by
using IP addresses or network
port numbers (or a range of
ports).
1. Select the Help tab (see Figure 9-14).
2. Click Upgrade Firmware to display a new window (see Figure 9-15).
Setting Up Filters
• To set up a filter using IP
addresses, enter the range of
IP addresses you wish to fil-
ter in the IP address fields.
Users who have filtered IP
addresses will not be able to
access the Internet at all. If
you only want to filter one IP
address instead of a range of
IP addresses, enter the same
value into both fields. For instance, if you wish to filter the PC with the IP
address of 192.168.1.5, enter 5 into both fields on one line: 192.168.1.5 ~
192.168.1.5. Click the Apply button when you’re done.
• To filter users by network port number, enter a network port number or a
range of network ports. Enter the port numbers you want to filter in the port
numbers fields. Users connected to the Router will no longer be able to
access any port number listed there.
Figure 9-15
Figure 9-16
3. Click the Browse button to find the firmware upgrade file that you down-
loaded from the Linksys website and then extracted.
4. Double-click the firmware file you downloaded and extracted. Click the
Upgrade button, and follow the instructions there.
Advanced
The following instructions are for advanced users or users whose setup needs
require special configuration. When you click the Advanced tab, you will be
able to set up these features. There are six additional tabs available.
Editing MAC Filter Setting
• This feature filters the Ethernet adapter’s specific MAC address from going
out to the Internet.
• Filters - Filters block specific internal users from Internet access and enable
Virtual Private Network (VPN) sessions.
• Forwarding - Sets up public services on your network.
• Dynamic Routing - Sets up the Router so it will automatically adjust to phys-
ical changes in the network’s layout.
• Static Routing - Sets up static routes needed when network information must
travel to a specific host or network.
• DMZ Host - Allows one local user to be exposed to the Internet for use of spe-
cial-purpose services such as online gaming or videoconferencing.
• MAC Address Cloning - Allows you to “clone” your Ethernet adapter’s MAC
address onto the Router.
• To check your Ethernet adapter’s MAC address, run winipcfg or ipconfig in
the command prompt, depending on which Windows operating system you
are using. To set the MAC filter, click the Edit MAC Filter Setting button.
When a second window appears, select the range in the drop-down box, and
at the MAC number prompt, enter the 12-digit MAC address you want to fil-
ter. Click the Apply button, before closing the window. For information on
obtaining a MAC address, go to “Appendix F: Finding the MAC Address and
IP Address for Your Ethernet Adapter.”
62
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Blocking WAN Requests
Using MTU (Maximum Transmission Unit)
• By enabling the Block WAN Request feature, you can prevent your network
from being “pinged,” or detected, by other Internet users. The Block WAN
Request feature also reinforces your network security by hiding your network
ports. Both functions of the Block WAN Request feature make it more diffi-
cult for outside users to work their way into your network.
• This feature specifies the largest packet size permitted for network transmis-
sion. Select Enable and enter the value desired. It is recommended that you
leave this value in the 1200 to 1500 range. For most DSL users, it is recom-
mended to use the value 1492. By default, MTU is set at 1500 when disabled.
Port Range Forwarding
• Click the Apply button to save your changes.
Using Multicast Pass Through
Port Range Forwarding (shown in Figure 9-17) sets up public services on your
network, such as web servers, ftp servers, e-mail servers, or other specialized
Internet applications. (Specialized Internet applications are any applications
that use Internet access to perform functions such as videoconferencing or
online gaming. Some Internet applications may not require any forwarding.)
When users send this type of request to your network via the Internet, the
Router will forward those requests to the appropriate PC. Before using
Forwarding, the Router’s DHCP function must be disabled under the DHCP tab
and the Router must be assigned a new static LAN IP address because the IP
address may change when using the DHCP server.
• This feature allows for multiple transmissions to specific recipients at the
same time. Select Enable to support the feature, or Disable to keep the
Router from multicasting.
Using IPSec Pass Through
• This feature lets you use IPSec Pass Through. To use this feature, click the
Enable button next to IPSec Pass Through, and then the Apply button.
• IPSec Pass Through is enabled by default. To disable IPSec Pass Through,
click on Disable and then the Apply button.
Using PPTP Pass Through
• Point-to-Point Tunneling Protocol is the method used to enable VPN
sessions. To enable this feature, click the Enable button next to PPTP Pass
Through, and click the Apply button.
• PPTP Pass Through is enabled by default. To disable this feature, click on
Disable next to PPTP Pass Through, and then the Apply button.
Using Remote Management
• This feature allows you to manage the Router from a remote location, via the
Internet. To enable this feature, click on Enable, and click the Apply button.
Remote Management must be activated before you can manage the Router
from a remote location.
• To disable Remote Management, click on Disable, and click the Apply but-
ton. If you wish to use this feature on the browser, enter http:\\<WAN IP
Address>:8080. (Enter your specific WAN IP Address in place of <WAN IP
Address>.)
• To disable this feature, click on Disable, and click the Apply button.
Using Remote Upgrade
• This feature allows you to upgrade the Router’s firmware from a remote loca-
tion. To enable Remote Upgrade, click on Enable, and then click the Apply
button. Remote Management must be activated before you can manage the
Router from a remote location.
Figure 9-17
64
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
If you need to forward all ports to one PC, see the “DMZ” section.
EtherFast® Cable/DSL Routers
• Telnet A terminal
emulation protocol
commonly used on
To add a server using Port Range Forwarding:
Internet
and
1. Enter the name of the application in the appropriate Customized Applications
TCP/IP-based net-
works. It allows a
user at a terminal or
computer to log onto
a remote device and
run a program.
field.
2. Next to the name of the application, enter the number or range of the exter-
nal port(s) used by the server or Internet application in the Ext. Port column.
Check with the Internet application software documentation for more infor-
mation.
• S M T P ( S i m p l e
3. On the same line, select the protocol UDP or TCP, or select both protocols.
Mail
Transfer
Protocol) The stan-
dard e-mail protocol
on the Internet. It is
a TCP/IP protocol
that defines the mes-
sage format and the
4. Enter the IP address of the server that you want the Internet users to be able
to access. To find the IP address, go to “Appendix F: Finding the MAC
Address and IP Address for Your Ethernet Adapter.”
5. Check the Enable box to enable the services you have defined. Port Range
Forwarding will not function if the Enable button is left unchecked. This is
disabled (unchecked) by default.
message
transfer
agent (MTA), which
stores and forwards
the mail.
Figure 9-18
6. Configure as many entries as needed—the Router supports up to 10 ranges of
ports. Click the Apply button when you are done.
• DNS (Domain Name System) The way that Internet domain names are
located and translated into IP addresses. A domain name is a meaningful and
easy-to-remember “handle” for an Internet address.
UPnP Forwarding
The UPnP Forwarding screen, shown in Figure 9-18, displays preset application
settings as well as options for customization of port services for other applications.
• TFTP (Trivial File Transfer Protocol) A version of the TCP/IP FTP proto-
col that has no directory or password capability.
The Preset Applications are among the most widely used Internet applications.
They include the following:
• Finger A UNIX command widely used on the Internet to find out informa-
tion about a particular user, such as a telephone number, whether the user is
currently logged on, and the last time the user was logged on. The person
being “fingered” must have placed his or her profile on the system in order
for the information to be available. Fingering requires entering the full
user@domain address.
• FTP (File Transfer Protocol) A protocol used to transfer files over a TCP/IP
network (Internet, UNIX, etc.). For example, after developing the HTML pages
for a website on a local machine, they are typically uploaded to the web server
using FTP. FTP includes functions to log onto the network, list directories, and
copy files. It can also convert between the ASCII and EBCDIC character codes.
FTP operations can be performed by typing commands at a command prompt
or via an FTP utility running under a graphical interface such as Windows. FTP
transfers can also be initiated from within a web browser by entering the URL
preceded by ftp://.
66
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
• HTTP (HyperText Transport Protocol) The communications protocol used
to connect to servers on the World Wide Web. Its primary function is to
establish a connection with a web server and transmit HTML pages to the
client web browser.
5. Enter the IP address of the server that you want the Internet users to be able
to access. To find the IP address, go to “Appendix F: Finding the MAC
Address and IP Address for Your Ethernet Adapter.”
6. Check the Enable box to enable the services you have defined. UPnP
Forwarding will not function if the Enable button is left unchecked. This is
disabled (unchecked) by default.
• POP3 (Post Office Protocol 3) A standard mail server commonly used on
the Internet. It provides a message store that holds incoming e-mail until
users log on and download it. POP3 is a simple system with little selectivi-
ty. All pending messages and attachments are downloaded at the same time.
POP3 uses the SMTP messaging protocol.
Port Triggering
• NNTP (Network News Transfer Protocol) The protocol used to connect to
Usenet groups on the Internet. Usenet newsreaders support the NNTP pro-
tocol.
• SNMP (Simple Network Management Protocol) A widely used network
monitoring and control protocol. Data is passed from SNMP agents, which
are hardware and/or software processes reporting activity in each network
device (hub, router, bridge, etc.) to the workstation console used to oversee
the network. The agents return information contained in a MIB
(Management Information Base), which is a data structure that defines what
is obtainable from the device and what can be controlled (turned off, on,
etc.).
You must check the Enable box to enable the applications you have defined.
Figure 9-19
To add a server using UPnP Forwarding:
From the Port Range Forwarding screen, shown in Figure 9-19, click the Port
Triggering button to allow the Router to watch outgoing data for specific port
numbers. The IP address of the computer that sends the matching data is
remembered by the Router, so that when the requested data returns through the
Router, the data is pulled back to the proper computer by way of IP address and
port mapping rules.
1. Enter the name of the application in the appropriate Application Name
field.
2. Next to the name of the application, enter the number of the external port
used by the server in the Ext. Port column. Check with the Internet appli-
cation software documentation for more information.
1. Enter the Application Name of the trigger.
3. On the same line, select the protocol UDP or TCP.
2. Enter the Trigger Port Range used by the application. Check with the
Internet application for the port number needed.
4. Enter the number of the internal port used by the server in the Int. Port col-
umn. Check with the Internet application software documentation for more
information.
3. Enter the Incoming Port Range used by the application. Check with the
Internet application for the port number needed.
4. Click the Apply button.
68
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Dynamic Routing
Static Routing
Figure 9-20
With Dynamic Routing (Figure 9-20) you can enable the Router to automati-
cally adjust to physical changes in the network’s layout. The Router, using the
RIP protocol, determines the network packets’ route based on the fewest num-
ber of hops between the source and the destination. The RIP protocol regular-
ly broadcasts routing information to other routers on the network. To set up
Dynamic Routing:
Figure 9-21
If the Router is connected to more than one network, it may be necessary to set
up a static route between them. A static route is a pre-determined pathway that
network information must travel to reach a specific host or network. From the
Static Routing tab, as shown in Figure 9-21, click the Show Routing Table but-
ton to view the current static routing configuration.
1. Choose the correct Working Mode. Gateway Mode should be used if the
Router is hosting your network’s connection to the Internet. Router Mode
should be selected if the Router exists on a network with other routers. In
Router Mode, any computer connected to the Router will not be able to
connect to the Internet unless you have another router function as the
Gateway.
To create a static route entry:
1. Select a Static Route Entry from the drop-down list. The Router supports
2. Choose a Dynamic Routing path protocol for either transmission (TX:)
up to 20 static route entries.
or reception (RX:) of network data.
To delete a Static Routing entry, select an entry, and click the Delete this
entry button.
When finished making your changes on this tab, click the Apply button to save
these changes, or click the Cancel button to undo your changes. For further
help on this tab, click the Help button.
Click the Show Routing Table button to open a chart displaying how data is
routed through your LAN.
70
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
2. Enter the following data to create a new static route.
EtherFast® Cable/DSL Routers
DMZ Host
Destination LAN IP: The Destination LAN IP is the address of the
remote network or host to which you want to assign a static route. Enter the
IP address of the host for which you wish to create a static route here. If
you are building a route to an entire network, be sure that the network por-
tion of the IP address is set to 0. For example, the Router’s standard IP
address is 192.168.1.1. Based on this address, the address of the routed net-
work is 192.168.1, with the last digit determining the Router’s place on the
network. Therefore you would enter the IP address 192.168.1.0 if you want-
ed to route to the Router’s entire network, rather than just to the Router.
Subnet Mask: The Subnet Mask (also known as the Network Mask) deter-
mines which portion of an IP address is the network portion, and which
portion is the host portion. Take, for example, a network in which the
Subnet Mask is 255.255.255.0. This determines (by using the values 255)
that the first three numbers of a network IP address identify this particular
network, while the last digit (from 1 to 254) identifies the specific host.
Figure 9-22
Default Gateway: This IP address should be the IP address of the gateway
device that allows for contact between the Router and the remote network
or host.
The DMZ Hosting feature, shown in Figure 9-22, allows one local user to be
exposed to the Internet for use of a special-purpose service such as Internet
gaming and videoconferencing.
Hop Count: This determines the maximum number of steps between net-
work nodes that data packets will travel. A node is any device on the net-
work, such as PCs, print servers, routers, etc.
Whereas Port Range Forwarding can only forward a maximum of 10 ranges of
ports, DMZ hosting forwards all the ports for one PC at the same time.
interface: Select LAN or WAN, depending on the location of the static
route’s final destination.
• To expose one PC, enter the computer’s IP address. To get the IP address of a
computer, refer to “Appendix F: Finding the MAC Address and IP Address
for Your Ethernet Adapter.”
3. When finished making your changes on this tab, click the Apply button to
save these changes, or click the Cancel button to undo your changes.
• Deactivate DMZ by entering a 0 in the field.
When finished, click the Apply button to save the settings. Otherwise, click the
Cancel button to undo changes made on this screen.
72
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
MAC Address Clone
Appendix A: Troubleshooting
Common Problems and Solutions
This appendix consists of two parts: “Common Problems and Solutions” and
“Frequently Asked Questions.” Provided are possible solutions to problems
regarding the installation and operation of the Router. If your situation is described
here, the problem should be solved by applying the corresponding solution. If you
Note: This is a
sample screen.
Please enter the
MAC Address
for your Network
Card/Adapter
into this field.
1. I need to set a static IP address on a PC.
The Router, by default, assigns an IP address range of 192.168.1.100 to
192.168.1.150 using the DHCP server on the Router. To set a static IP address, you
can only use the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to
192.168.1.254. Each PC or network device that uses TCP/IP must have a unique
address to identify itself in a network. If the IP address is not unique to a network,
Windows will generate an IP conflict error message. You can assign a static IP
address to a PC by performing the following steps:
Figure 9-23
The Router’s MAC address is a 12-digit code assigned to a unique piece of
hardware for identification, like a social security number. If your ISP requires
MAC address registration, find your adapter’s MAC address by following the
instructions in “Appendix F: Finding the MAC Address and IP Address for
Your Ethernet Adapter.”
For Windows 95, 98, and Me:
A. Click Start, Settings, and Control Panel. Double-click Network.
B. In The following network components are installed box, select the TCP/IP->
associated with your Ethernet adapter. If you only have one Ethernet adapter
installed, you will only see one TCP/IP line with no association to an Ethernet
adapter. Highlight it and click the Properties button.
C. In the TCP/IP properties window, select the IP address tab, and select Specify
an IP address. Enter a unique IP address that is not used by any other com-
puter on the network connected to the Router. You can only use an IP address
in the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to
192.168.1.254. Make sure that each IP address is unique for each PC or net-
work device.
Enter the 12 digits of your adapter’s MAC address in the on-screen fields (see
Figure 9-23). This “clones” your network adapter’s MAC address onto the
Router, so you do NOT have to call your ISP to change the registered MAC
address to the Router’s MAC address.
When finished making your changes on this tab, click the Apply button to save
these changes, or click the Cancel button to undo your changes.
D. Click the Gateway tab, and in the New Gateway prompt, enter 192.168.1.1,
which is the default IP address of the Router. Click the Add button to accept
the entry.
E. Click the DNS tab, and make sure the DNS Enabled option is selected. Enter
the Host and Domain names (e.g., John for Host and home for Domain).
Enter the DNS entry provided by your ISP. If your ISP has not provided the
DNS IP address, contact your ISP to get that information or go to its website
for the information.
F. Click the OK button in the TCP/IP properties window, and click Close or the
OK button for the Network window.
G. Restart the computer when asked.
74
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
For Windows 2000:
For Windows XP:
A. Click Start, Settings, and Control Panel. Double-click Network and
Dial-Up Connections.
B. Right-click the Local Area Connection that is associated with the Ethernet
adapter you are using, and select the Properties option.
The following instructions assume you are running Windows XP with the default
interface. If you are using the Classic interface (where the icons and menus look
like previous Windows versions), please follow the instructions for Windows 2000.
C. In the Components checked are used by this connection box, highlight
Internet Protocol (TCP/IP), and click the Properties button. Select Use
the following IP address option.
A. Click Start and Control Panel.
B. Click the Network and Internet Connections icon and then the Network
Connections icon.
D. Enter a unique IP address that is not used by any other computer on the
network connected to the Router. You can only use an IP address in the
ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to 192.168.1.254.
E. Enter the Subnet Mask, 255.255.255.0.
C. Right-click the Local Area Connection that is associated with the Ethernet
adapter you are using, and select the Properties option.
D. In the This connection uses the following items box, highlight Internet
Protocol (TCP/IP). Click the Properties button.
F. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
G. Toward the bottom of the window, select Use the following DNS server
addresses, and enter the Preferred DNS server and Alternative DNS
server (provided by your ISP). Contact your ISP or go on its website to find
the information.
H. Click the OK button in the Internet Protocol (TCP/IP) Properties window,
and click the OK button in the Local Area Connection Properties window.
I. Restart the computer if asked.
E. Enter a unique IP address that is not used by any other computer on the net-
work connected to the Router. You can only use an IP address in the ranges
192.168.1.2 to 192.168.1.99 and 192.168.1.151 to 192.168.1.254.
F. Enter the Subnet Mask, 255.255.255.0.
G. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
H. Toward the bottom of the window, select Use the following DNS server
addresses, and enter the Preferred DNS server and Alternative DNS server
(provided by your ISP). Contact your ISP or go on its website to find the infor-
mation.
For Windows NT 4.0:
I. Click the OK button in the Internet Protocol (TCP/IP) Properties window.
Click the OK button in the Local Area Connection Properties window.
A. Click Start, Settings, and Control Panel. Double-click the Network icon.
B. Click the Protocol tab, and double-click TCP/IP Protocol.
C. When the window appears, make sure you have selected the correct
Adapter for your Ethernet adapter.
2. I want to test my Internet connection.
A. Check your TCP/IP settings.
D. Select Specify an IP address, and enter a unique IP address that is not
used by any other computer on the network connected to the Router. You
can only use an IP address in the ranges 192.168.1.2 to 192.168.1.99 and
192.168.1.151 to 192.168.1.254.
For Windows 95, 98, and Me:
Refer to “Appendix D: Installing the TCP/IP Protocol” and “Chapter 7:
Configure the PCs” for details. Make sure Obtain IP address automatically
is selected in the settings.
E. Enter the Subnet Mask, 255.255.255.0.
F. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
G. Click the DNS tab, and enter the Host and Domain names (e.g., John for
Host and home for Domain). Under DNS Service Search Order, click the
Add button. Enter the DNS IP address in the DNS Server field, and click
the Add button. Repeat this action for all DNS IP addresses given by your
ISP.
H. Click the OK button in the TCP/IP Protocol Properties window, and click
the Close button in the Network window.
I. Restart the computer if asked.
For Windows 2000:
• Click Start, Settings, and Control Panel. Double-click Network and Dial-
Up Connections.
• Right-click the Local Area Connection that is associated with the Ethernet
adapter you are using, and select the Properties option.
• In the Components checked are used by this connection box, highlight
Internet Protocol (TCP/IP), and click the Properties button. Make sure
that Obtain an IP address automatically and Obtain DNS server address
automatically are selected.
76
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
• Click the OK button in the Internet Protocol (TCP/IP) Properties win-
dow, and click the OK button in the Local Area Connection Properties
window.
C. In the command prompt, type ping 192.168.1.1 and press the Enter key.
• If you get a reply, the computer is communicating with the Router.
• If you do NOT get a reply, please check the cable, and make sure Obtain
an IP address automatically is selected in the TCP/IP settings for your
Ethernet adapter.
• Restart the computer if asked.
For Windows XP:
The following instructions assume you are running Windows XP with the
default interface. If you are using the Classic interface (where the icons and
menus look like previous Windows versions), please follow the instructions
for Windows 2000.
D. In the command prompt, type ping followed by your WAN IP address and
press the Enter key. The WAN IP Address can be found in the web inter-
face of the Router. For example, if your WAN IP address is 1.2.3.4, you
would enter ping 1.2.3.4 and press the Enter key.
• If you get a reply, the computer is connected to the Router.
• Click Start and Control Panel.
• Click the Network and Internet Connections icon and then the
Network Connections icon.
• If you do NOT get a reply, try the ping command from a different com-
puter to verify that your original computer is not the cause of the problem.
• Right-click the Local Area Connection that is associated with the
Ethernet adapter you are using, and select the Properties option.
• In the This connection uses the following items box, highlight Internet
Protocol (TCP/IP), and click the Properties button. Make sure that
Obtain an IP address automatically and Obtain DNS server address
automatically are selected.
• Click the OK button in the Internet Protocol (TCP/IP) Properties win-
dow, and click the OK button in the Local Area Connection Properties
window.
E. In the command prompt, type ping www.yahoo.com and press the Enter
key.
• If you get a reply, the computer is connected to the Internet. If you can-
not open a webpage, try the ping command from a different computer to
verify that your original computer is not the cause of the problem.
• If you do NOT get a reply, there may be a problem with the connection.
Try the ping command from a different computer to verify that your orig-
inal computer is not the cause of the problem.
3. I am not getting an IP address on the WAN with my Internet connection.
A. Refer to “Problem #2, I want to test my Internet connection” to verify that
you have connectivity.
• Restart the computer if asked.
For Windows NT 4.0:
• Click Start, Settings, and Control Panel. Double-click the Network
icon.
• Click the Protocol tab, and double-click on TCP/IP Protocol.
• When the window appears, make sure you have selected the correct
Adapter for your Ethernet adapter and set it for Obtain an IP address
from a DHCP server.
• Click the OK button in the TCP/IP Protocol Properties window, and
click the Close button in the Network window.
• Restart the computer if asked.
B. If you need to register the MAC address of your Ethernet adapter with your
ISP, please see “Appendix F: Finding the MAC address and IP Address for
Your Ethernet Adapter.” If you need to clone the MAC address of your
Ethernet adapter onto the Router, see the MAC Address Clone section of
“Chapter 6: The Cable/DSL VPN Router’s Web-based Utility” for details.
C. Make sure you are using the right WAN settings. Contact your ISP to see if
your WAN connection type is DHCP, Static IP Address, or PPPoE (com-
monly used by DSL consumers). Please refer to the Setup section of
“Chapter 6: The Cable/DSL VPN Router’s Web-based Utility” for details
on WAN settings.
B. Open a command prompt.
D. Make sure you have the right cable. Check to see if the WAN column has a
solidly lit Link LED.
E. Make sure the cable connecting from your cable or DSL modem is con-
nected to the Router’s WAN port. Verify that the Status page of the Router’s
web interface shows a valid IP address from your ISP.
• For Windows 95, 98, and Me, please click Start and Run. In the Open
field, type in command. Press the Enter key or click the OK button.
• For Windows NT, 2000, and XP, please click Start and Run. In the
Open field, type cmd. Press the Enter key or click the OK button.
78
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
F. Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds,
and then turn on the Router, cable/DSL modem, and computer. Check the
Status tab of the Router’s web-based utility to see if you get an IP address.
Your VPN may require port 500/UDP packets to be passed to the computer that
is connecting to the IPSec server. Refer to “Problem #7, I need to set up online
game hosting or use other Internet applications” for details.
4. I am not able to access the Router’s web interface Setup page.
A. Refer to “Problem #2, I want to test my Internet connection” to verify that
your computer is properly connected to the Router.
6. I need to set up a server behind my Router.
B. Refer to “Appendix F: Finding the MAC Address and IP address for Your
Ethernet Adapter” to verify that your computer has an IP Address, Subnet
Mask, Gateway, and DNS.
C. Set a static IP address on your system; refer to “Problem #1: I need to set a
static IP address.”
To use a server like a web, ftp, or mail server, you need to know the respective
port numbers they are using. For example, port 80 (HTTP) is used for web;
port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and port 110
(POP3 incoming) are used for the mail server. You can get more information
by viewing the documentation provided with the server you installed. Follow
these steps to set up port forwarding through the Router’s web-based utility. We
will be setting up web, ftp, and mail servers.
D. Refer to “Problem #10: I need to remove the proxy settings or the dial-up
pop-up window (for PPPoE users).”
5. I can’t get my Virtual Private Network (VPN) working through the Router.
address of the Router, and go to the Advanced => Filter tab. Make sure you
have IPsec pass-through and/or PPTP pass-through enabled.
IP address of the Router. Go to the Advanced => Forwarding tab.
B. Enter any name you want to use for the Customized Application.
C. Enter the Ext. Port range of the service you are using. For example, if you
have a web server, you would enter the range 80 to 80.
VPNs that use IPSec with the ESP (Encapsulation Security Payload known as
protocol 50) authentication will work fine. At least one IPSec session will work
through the Router; however, simultaneous IPSec sessions may be possible,
depending on the specifics of your VPNs.
D. Check the protocol you will be using, TCP and/or UDP.
E. Enter the IP address of the PC or network device that you want the port
server to go to. For example, if the web server’s Ethernet adapter IP address
is 192.168.1.100, you would enter 100 in the field provided. Check
“Appendix F: Finding the MAC Address and IP Address for Your Ethernet
Adapter” for details on getting an IP address.
VPNs that use IPSec and AH (Authentication Header known as protocol 51)
are incompatible with the Router. AH has limitations due to occasional incom-
patibility with the NAT standard.
F. Check the Enable option for the port services you want to use. Consider the
example below:
Change the IP address for the Router to another subnet to avoid a conflict
between the VPN IP address and your local IP address. For example, if your
VPN server assigns an IP address 192.168.1.X (X is a number from 1 to 254)
and your local LAN IP address is 192.168.1.X (X is the same number used in
the VPN IP address), the Router will have difficulties routing information to
the right location. If you change the Router’s IP address to 192.168.2.1, that
should solve the problem. Change the Router’s IP address through the Setup tab
of the web interface. If you assigned a static IP address to any computer or net-
work device on the network, you need to change its IP address accordingly to
192.168.2.Y (Y being any number from 1 to 254). Note that each IP address
must be unique within the network.
Customized
Application
Web server
FTP server
SMTP (outgoing) 25 to 25
POP3 (incoming) 110 to 110
Ext. Port
TCP
UDP
X
IP Address
Enable
80 to 80
21 to 21
X
X
X
X
192.168.1.100
192.168.1.101
192.168.1.102
192.168.1.102
X
X
X
X
X
X
When you have completed the configuration, click the Apply button.
80
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
7. I need to set up online game hosting or use other Internet applications.
EtherFast® Cable/DSL Routers
8. I can’t get the Internet game, server, or application to work.
If you want to play online games or use Internet applications, most will work
without doing any port forwarding or DMZ hosting. There may be cases when
you want to host an online game or Internet application. This would require
you to set up the Router to deliver incoming packets or data to a specific com-
puter. This also applies to the Internet applications you are using. The best way
to get the information on what port services to use is to go to the website of the
online game or application you want to use. Follow these steps to set up online
game hosting or use a certain Internet application:
If you are having difficulties getting any Internet game, server, or application
to function properly, consider exposing one PC to the Internet using
DeMilitarized Zone (DMZ) hosting. This option is available when an applica-
tion requires too many ports or when you are not sure which port services to
use. Make sure you disable all the forwarding entries if you want to success-
fully use DMZ hosting, since forwarding has priority over DMZ hosting. (In
other words, data that enters the Router will be checked first by the forwarding
settings. If the port number that the data enters from does not have port for-
warding, then the Router will send the data to whichever PC or network device
you set for DMZ hosting.) Follow these steps to set DMZ hosting:
address of the Router. Go to the Advanced => Forwarding tab.
B. Enter any name you want to use for the Customized Application.
C. Enter the Ext. Port range of the service you are using. For example, if you
want to host Unreal Tournament (UT), you would enter the range 7777 to
27900.
IP address of the Router. Go to the Advanced => Forwarding tab.
B. Disable or remove the entries you have entered for forwarding. Keep this
information in case you want to use it at a later time.
D. Check the protocol you will be using, TCP and/or UDP.
E. Enter the IP address of the PC or network device that you want the port
server to go to. For example, if the web server’s Ethernet adapter IP address
is 192.168.1.100, you would enter 100 in the field provided. Check
“Appendix F: Finding the MAC Address and IP Address for Your Ethernet
Adapter” for details on getting an IP address.
C. Click the DMZ Host tab.
D. Enter the Ethernet adapter’s IP address of the computer you want exposed
to the Internet. This will bypass the NAT firewall for that computer. Please
refer to “Appendix F: Finding the MAC Address and IP Address for Your
Ethernet Adapter” for details on getting an IP address.
F. Check the Enable option for the port services you want to use. Consider the
example below:
Once completed with the configuration, click the Apply button.
9. I forgot my password, or the password prompt always appears when saving set-
tings to the Router.
Reset the Router to factory default by pressing the Reset button for 30 seconds
and then releasing it. If you are still getting prompted for a password when sav-
ing settings, then perform the following steps:
Customized
Application
UT
Halflife
PC Anywhere
VPN IPSEC
Ext. Port
TCP
X
UDP
IP Address
Enable
7777 to 27900
X
X
X
X
192.168.1.100
192.168.1.105
192.168.1.102
192.168.1.100
X
X
X
X
27015 to 27015 X
5631 to 5631
500 to 500
address of the Router. Enter the default password admin, and click the
Password tab.
When you have completed the configuration, click the Apply button.
B. Enter a different password in the Router Password field, and enter the
same password in the second field to confirm the password.
C. Click the Apply button.
82
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
10. I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-
up window.
If you have proxy settings, you need to disable these on your computer.
Because the Router is the gateway for the Internet connection, the computer
does not need any proxy settings to gain access. Please follow these directions
to verify that you do not have any proxy settings and that the browser you use
is set to connect directly to the LAN.
13. The firmware upgrade failed, and/or the Diag LED is flashing.
The upgrade could have failed for a number of reasons. Follow these steps to
upgrade the firmware and/or make the Diag LED stop flashing:
A. If the firmware upgrade failed, use the TFTP program (it was downloaded
along with the firmware). Open the pdf that was downloaded along with the
firmware and TFTP program, and follow the pdf’s instructions.
B. Set a static IP address on the PC; refer to “Problem #1, I need to set a stat-
ic IP address.” Use the following IP address settings for the computer you
are using:
For Microsoft Internet Explorer 5.0 or higher:
A. Click Start, Settings, and Control Panel. Double-click Internet Options.
B. Click the Connections tab.
C. Click the LAN settings button and remove anything that is checked.
D. Click the OK button to go back to the previous screen.
E. Click the option Never dial a connection. This will remove any dial-up
pop-ups for PPPoE users.
IP Address: 192.168.1.50
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
C. Perform the upgrade using the TFTP program or the Router’s web-based
utility through its Help tab.
For Netscape 4.7 or higher:
A. Start Netscape Navigator, and click Edit, Preferences, Advanced, and
14. My DSL service’s PPPoE is always disconnecting.
Proxies.
B. Make sure you have Direct connection to the Internet selected on this
PPPoE is not actually a dedicated or always-on connection. The DSL ISP can
disconnect the service after a period of inactivity, just like a normal phone dial-
up connection to the Internet. There is a setup option to “keep alive” the con-
nection. This may not always work, so you may need to re-establish connec-
tion periodically.
screen.
C. Close all the windows to finish.
11. To start over, I need to set the Router to factory default.
Hold the Reset button for up to 30 seconds and then release it. This will return
the password, forwarding, and other settings on the Router to the factory
default settings. In other words, the Router will revert to its original factory
configuration.
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. In the Setup tab, select the option Keep Alive, and set the Redial Period
option at 20 (seconds).
12. I need to upgrade the firmware.
In order to upgrade the firmware with the latest features, you need to go to the
these steps:
D. Click the Apply button.
E. Click the Status tab, and click the Connect button.
F. You may see the login status display as Connecting. Press the F5 key to
refresh the screen, until you see the login status display as Connected.
G. Click the Apply button to continue.
latest firmware.
B. To upgrade the firmware, follow the steps in the Help section found in
“Chapter 9: The Cable/DSL Router’s Web-based Utility.”
If the connection is lost again, follow steps E to G to re-establish connection.
84
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
15. I can't access my email, web, or VPN, or I am getting corrupted data from the
Internet.
The Maximum Transmission Unit (MTU) setting may need to be adjusted. By
default, the MTU is set at 1500. For most DSL users, it is strongly recom-
mended to use MTU 1492. If you are having some difficulties, perform the fol-
lowing steps:
17. The Diag LED stays lit continuously.
• The Diag LED lights up when the device is first powered up. Meantime,
the system will boot up itself and check for proper operation. After fin-
ishing the checking procedure, the LED turns off to show that the system
is working fine. If the LED remains lit after this time, the device is not
working properly. Try to flash the firmware by assigning a static IP
address to the computer, and then upgrade the firmware. Try using the
following settings, IP Address: 192.168.1.50 and Subnet Mask:
255.255.255.0.
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. Click the Advanced => Filter tab.
D. Look for the MTU option, and select Enable. In the Size field, enter 1492.
E. Click the Apply button to continue.
18. When I enter a URL or IP address, I get a time-out error or am prompted to retry.
• Check if other PCs work. If they do, ensure that your workstation’s IP set-
tings are correct (IP Address, Subnet Mask, Default Gateway, and DNS).
Restart the computer that is having a problem.
If your difficulties continue, change the Size to different values. Try this list of
values, one value at a time, in this order, until your problem is solved:
• If the PCs are configured correctly, but still not working, check the
Router. Ensure that it is connected and ON. Connect to it and check its
settings. (If you cannot connect to it, check the LAN and power connec-
tions.)
• If the Router is configured correctly, check your Internet connection
(DSL/cable modem, etc.) to see if it is working correctly.You can remove
the Router to verify a direct connection.
1462
1400
1362
1300
16. I need to use port triggering.
• Manually configure the TCP/IP with a DNS address provided by your
ISP.
Port triggering looks at the outgoing port services used and will trigger the
Router to open a specific port, depending on which port an Internet application
uses. Follow these steps:
• Make sure that your browser is set to connect directly and that any dial-
up is disabled. For Internet Explorer, click Tools, Internet Options, and
then the Connection tab. Make sure that Internet Explorer is set to Never
dial a connection. For Netscape Navigator, click Edit, Preferences,
Advanced, and Proxy. Make sure that Netscape Navigator is set to
Direct connection to the Internet.
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. Click theAdvanced => Forwarding tab, and click the Port Trigger button.
D. Enter any name you want to use for the Application Name.
E. Enter the Triggered Port Range. Check with your Internet application
provider for more information on which outgoing port services it is using.
F. Enter the Incoming Port Range. Check with your Internet Application
provider for more information on which incoming port services are
required by the Internet application.
19. The Full/Col LED keeps flickering continuously.
• Check the Category 5 Ethernet cable and its RJ-45 connectors.
• There may be interference with other network devices. Try removing
other PCs or network devices to see if the problem persists. Eliminate
each network device one at a time to determine the cause.
86
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Does the Router support ICQ send file? Yes, with the following fix: click ICQ
menu -> preference -> connections tab->, and check I am behind a fire-
wall or proxy. Then set the firewall time-out to 80 seconds in the firewall set-
ting. The Internet user can then send a file to a user behind the Router.
Frequently Asked Questions
What is the maximum number of IP addresses that the Router will support? The
Router will support up to 253 IP addresses.
I set up an Unreal Tournament Server, but others on the LAN cannot join. What do
I need to do? If you have a dedicated Unreal Tournament server running, you
need to create a static IP for each of the LAN computers and forward ports
7777, 7778, 7779, 7780, 7781, and 27900 to the IP address of the server. You
can also use a port forwarding range of 7777 ~ 27900. If you want to use the
UT Server Admin, forward another port (8080 usually works well but is used
for remote admin. You may have to disable this.), and then in the
[UWeb.WebServer] section of the server.ini file, set the ListenPort to 8080 (to
match the mapped port above) and ServerName to the IP assigned to the
Router from your ISP.
Is IPSec Pass-Through supported by the Router? Yes, it is a built-in feature that
the Router automatically enables.
Where is the Router installed on the network? In a typical environment, the
Router is installed between the cable/DSL modem and the LAN. Plug the
Router into the cable/DSL modem’s Ethernet port.
Does the Router support IPX or AppleTalk? No. TCP/IP is the only protocol stan-
dard for the Internet and has become the global standard for communications.
IPX, a NetWare communications protocol used only to route messages from
one node to another, and AppleTalk, a communications protocol used on
Apple and Macintosh networks, can be used for LAN to LAN connections,
but those protocols cannot connect from WAN to LAN.
Can multiple gamers on the LAN get on one game server and play simultaneously
with just one public IP address? It depends on which network game or what
kind of game server you are using. For example, Unreal Tournament supports
multi-login with one public IP.
Does the WAN connection of the Router support 100 Mbps Ethernet? Because of
the speed limitations of broadband Internet connections, the Router’s current
hardware design supports 10 Mbps Ethernet on its WAN port. It does, of
course, support 100 Mbps over the auto-sensing Fast Ethernet 10/100 switch
on the LAN side of the Router.
How do I get Half-Life: Team Fortress to work with the Router? The default client
port for Half-Life is 27005. The computers on your LAN need to have
“+clientport 2700x” added to the HL shortcut command line; the x would be
6, 7, 8, and on up. This lets multiple computers connect to the same server.
One problem: Version 1.0.1.6 won’t let multiple computers with the same CD
key connect at the same time, even if on the same LAN (not a problem with
1.0.1.3). As far as hosting games, the HL server does not need to be in the
DMZ. Just forward port 27015 to the local IP address of the server computer.
What is Network Address Translation and what is it used for? Network Address
Translation (NAT) translates multiple IP addresses on the private LAN to one
public address that is sent out to the Internet. This adds a level of security
since the address of a PC connected to the private LAN is never transmitted
on the Internet. Furthermore, NAT allows the Router to be used with low cost
Internet accounts, such as DSL or cable modems, when only one TCP/IP
address is provided by the ISP. The user may have many private addresses
behind this single address provided by the ISP.
How can I block corrupted FTP downloads? If you are experiencing corrupted files
when you download a file with your FTP client, try using another FTP program.
The web page hangs; downloads are corrupt, or nothing but junk characters are
being displayed on the screen. What do I need to do? Force your Ethernet
adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate”
feature of your Ethernet adapter as a temporary measure. (Please look at the
Network Control Panel in your Ethernet adapter’s Advanced Properties tab.)
Make sure that your proxy setting is disabled in the browser. Check our web-
Does the Router support any operating system other than Windows 95, Windows
98, Windows 2000, Windows NT, or Windows XP? Yes, but Linksys does not, at
this time, provide technical support for setup, configuration or troubleshoot-
ing of any non-Windows operating systems.
88
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
If all else fails in the installation, what can I do? Reset the Router by holding
down the reset button until the Diag LED fully turns on and off. Reset your
cable or DSL modem by powering the unit off and then on. Obtain and flash
the latest firmware release that is readily available on the Linksys website,
Does the Router pass PPTP packets or actively route PPTP sessions? The Router
allows PPTP packets to pass through.
Is the Router cross-platform compatible? Any platform that supports Ethernet
and TCP/IP is compatible with the Router.
How will I be notified of new Router firmware upgrades? All Linksys firmware
can be downloaded for free. The Router’s firmware can be upgraded with
TFTP programs. If the Router’s Internet connection is working well, there is
no need to download a newer firmware version, unless that version contains
new features that you would like to use. Downloading a more current version
of Router firmware will not enhance the quality or speed of your Internet con-
nection, and may disrupt your current connection stability.
How many ports can be simultaneously forwarded? Theoretically, the Router can
establish 520 sessions at the same time, but you can only forward 10 ranges
of ports.
Does the Router replace a modem? Is there a cable or DSL modem in the Router?
No, this version of the Router must work in conjunction with a cable or DSL
modem.
Which modems are compatible with the Router? The Router is compatible with
Will the Router function in a Macintosh environment? Yes, but the Router’s setup
pages are accessible only through Internet Explorer 4.0 or Netscape
Navigator 4.0 or higher for Macintosh.
virtually any cable or DSL modem that supports Ethernet.
What are the advanced features of the Router? The Router’s advanced features
include IP Filtering, Port Range Forwarding, Dynamic Routing, Static
Routing, DMZ hosting, and MAC Address Cloning.
I am not able to get the web configuration screen for the Router. What can I do?
You may have to remove the proxy settings on your Internet browser, e.g.,
Netscape Navigator or Internet Explorer. Or remove the dial-up settings on
your browser. Check with your browser documentation, and make sure that
your browser is set to connect directly and that any dial-up is disabled. Make
sure that your browser is set to connect directly and that any dial-up is dis-
abled. For Internet Explorer, click Tools, Internet Options, and then the
Connection tab. Make sure that Internet Explorer is set to Never dial a con-
nection. For Netscape Navigator, click Edit, Preferences, Advanced, and
Proxy. Make sure that Netscape Navigator is set to Direct connection to the
Internet.
What is the maximum number of VPN sessions allowed by the Router?
The maximum number depends on many factors. At least one IPSec session
will work through the Router; however, simultaneous IPSec sessions may be
possible, depending on the specifics of your VPNs.
How big is the memory buffer on the Router? 1MB buffer and 512KB flash.
How can I check whether I have static or DHCP IP Addresses? Consult your ISP
to obtain this information.
What is DMZ Hosting? Demilitarized Zone (DMZ) allows one IP address (com-
puter) to be exposed to the Internet. Some applications require multiple
TCP/IP ports to be open. It is recommended that you set your computer with
a static IP if you want to use DMZ Hosting. To get the LAN IP address, see
“Appendix F: Finding the MAC Address and IP Address for Your Ethernet
Adapter.”
How do I get mIRC to work with the Router? Under the Port Range Forwarding
tab, set port forwarding to 113 for the PC on which you are using mIRC.
If your questions are not addressed here, refer to the Linksys website,
If DMZ Hosting is used, does the exposed user share the public IP with the Router?
No.
90
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Bridge - A device that interconnects different networks together.
Appendix B: Glossary
Broadband - A data-transmission scheme in which multiple signals share the
bandwidth of a medium. This allows the transmission of voice, data, and video
signals over a single medium. Cable television uses broadband techniques to
deliver dozens of channels over one cable.
10BaseT - An Ethernet standard that uses twisted wire pairs.
100BaseTX - IEEE physical layer specification for 100 Mbps over two pairs of
Category 5 UTP or STP wire.
Browser - A browser is an application program that provides a way to look at
and interact with all the information on the World Wide Web or PC. The word
“browser” seems to have originated prior to the Web as a generic term for user
interfaces that let you browse text files online.
1000BASE-T - Provides half-duplex (CSMA/CD) and full-duplex 1000 Mbps
Ethernet service over Category 5 links as defined by ANSI/TIA/EIA-568-A.
Topology rules for 1000BASE-T are the same as those used for 100BASE-T.
Category 5 link lengths are limited to 100 meters by the ANSI/TIA/EIA-568-A
cabling standard. Only one CSMA/CD repeater will be allowed in a collision
domain.
Cable Modem - A device that connects a computer to the cable television net-
work, which in turn connects to the Internet. Once connected, cable modem
users have a continuous connection to the Internet. Cable modems feature asym-
metric transfer rates: around 36 Mbps downstream (from the Internet to the
computer), and from 200 Kbps to 2 Mbps upstream (from the computer to the
Internet).
Adapter - Printed circuit board that plugs into a PC to add to capabilities or con-
nectivity to a PC. In a networked environment, a network interface card (NIC)
is the typical adapter that allows the PC or server to connect to the intranet
and/or Internet.
CAT 3 - ANSI/EIA (American National Standards Institute/Electronic
Industries Association) Standard 568 is one of several standards that specify
“categories” (the singular is commonly referred to as “CAT”) of twisted pair
cabling systems (wires, junctions, and connectors) in terms of the data rates that
they can sustain. CAT 3 cable has a maximum throughput of 16 Mbps and is
usually utilized for 10BaseT networks.
Auto-negotiate - To automatically determine the correct settings. The term is
often used with communications and networking. For example, Ethernet 10/100
cards, hubs, and switches can determine the highest speed of the node they are
connected to and adjust their transmission rate accordingly.
Backbone – The part of a network that connects most of the systems and net-
works together and handles the most data.
CAT 5 - ANSI/EIA (American National Standards Institute/Electronic
Industries Association) Standard 568 is one of several standards that specify
“categories” (the singular is commonly referred to as “CAT”) of twisted pair
cabling systems (wires, junctions, and connectors) in terms of the data rates that
they can sustain. CAT 5 cable has a maximum throughput of 100 Mbps and is
usually utilized for 100BaseTX networks.
Bandwidth - The transmission capacity of a given facility, in terms of how
much data the facility can transmit in a fixed amount of time; expressed in bits
per second (bps).
Bit – A binary digit. The value—0 or 1—used in the binary numbering system.
Also, the smallest form of data.
CAT 5e - The additional cabling performance parameters of return loss and far-
end crosstalk (FEXT) specified for 1000BASE-T and not specified for
10BASE-T and 100BASE-TX are related to differences in the signaling imple-
mentation. 10BASE-T and 100BASE-TX signaling is unidirectional—signals
are transmitted in one direction on a single wire pair. In contrast, Gigabit
Ethernet is bi-directional—signals are transmitted simultaneously in both direc-
tions on the same wire pair; that is, both the transmit and receive pair occupy the
same wire pair.
Boot – To cause the computer to start executing instructions. Personal comput-
ers contain built-in instructions in a ROM chip that are automatically executed
on startup. These instructions search for the operating system, load it, and pass
control to it.
Bottleneck – A traffic slowdown that results when too many network nodes try
to access a single node, often a server node, at once.
92
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
CPU (Central Processing Unit) - The computing part of the computer. Also
called the “processor,” it is made up of the control unit and ALU.
DHCP supports static addresses for computers containing Web servers that need
a permanent IP address.
CSMA/CD (Carrier Sense Multiple Access/Collision Detection) - The LAN
access method used in Ethernet. When a device wants to gain access to the net-
work, it checks to see if the network is quiet (senses the carrier). If it is not, it
waits a random amount of time before retrying. If the network is quiet and two
devices access the line at exactly the same time, their signals collide. When the
collision is detected, they both back off and each waits a random amount of time
before retrying.
DMZ - (DeMilitarized Zone) allows one IP address (or computer) to be exposed
to the Internet. Some applications require multiple TCP/IP ports to be open. It
is recommended that you set your computer with a static IP address if you want
to use DMZ Hosting.
DNS - The Domain Name System (DNS) is the way that Internet domain names
are located and translated into Internet Protocol (IP) addresses. A domain name
is a meaningful and easy-to-remember “handle” for an Internet address.
Daisy Chain - Connected in series, one after the other. Transmitted signals go
to the first device, then to the second, and so on.
Domain - A subnetwork comprised of a group of clients and servers under the
control of one security database. Dividing LANs into domains improves per-
formance and security.
Database - A database is a collection of data that is organized so that its con-
tents can easily be accessed, managed, and updated.
Download - To receive a file transmitted over a network. In a communications
Data Packet - One frame in a packet-switched message. Most data communi-
cations is based on dividing the transmitted message into packets. For example,
an Ethernet packet can be from 64 to 1518 bytes in length.
session, download means receive, and upload means transmit.
Driver - A workstation or server software module that provides an interface
between a network interface card and the upper-layer protocol software running
in the computer; it is designed for a specific NIC, and is installed during the ini-
tial installation of a network-compatible client or server operating system.
Default Gateway - The routing device used to forward all traffic that is not
addressed to a station within the local subnet.
DHCP (Dynamic Host Configuration Protocol) - A protocol that lets network
administrators centrally manage and automate the assignment of Internet
Protocol (IP) addresses in an organization's network. Using the Internet’s set of
protocol (TCP/IP), each machine that can connect to the Internet needs a unique
IP address. When an organization sets up its computer users with a connection
to the Internet, an IP address must be assigned to each machine. Without DHCP,
the IP address must be entered manually at each computer and, if computers
move to another location in another part of the network, a new IP address must
be entered. DHCP lets a network administrator supervise and distribute IP
addresses from a central point and automatically sends a new IP address when a
computer is plugged into a different place in the network.
DSSS (Direct-Sequence Spread-Spectrum) - DSSS generates a redundant bit
pattern for each bit to be transmitted. This bit pattern is called a chip (or chip-
ping code). The longer the chip, the greater the probability that the original data
can be recovered. Even if one or more bits in the chip are damaged during trans-
mission, statistical techniques embedded in the radio can recover the original
data without the need for retransmission. To an unintended receiver, DSSS
appears as low power wideband noise and is rejected (ignored) by most narrow-
band receivers.
Dynamic IP Address - An IP address that is automatically assigned to a client
station in a TCP/IP network, typically by a DHCP server. Network devices that
serve multiple users, such as servers and printers, are usually assigned static IP
addresses.
DHCP uses the concept of a “lease” or amount of time that a given IP address
will be valid for a computer. The lease time can vary depending on how long a
user is likely to require the Internet connection at a particular location. It’s espe-
cially useful in education and other environments where users change frequent-
ly. Using very short leases, DHCP can dynamically reconfigure networks in
which there are more computers than there are available IP addresses.
Dynamic Routing - The ability for a router to forward data via a different route
based on the current conditions of the communications circuits. For example, it
can adjust for overloaded traffic or failing lines and is much more flexible than
static routing, which uses a fixed forwarding path.
94
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Ethernet - IEEE standard network protocol that specifies how data is placed on
and retrieved from a common transmission medium. Has a transfer rate of 10
Mbps. Forms the underlying transport vehicle used by several upper-level pro-
tocols, including TCP/IP and XNS.
Full Duplex - The ability of a device or line to transmit data simultaneously in
both directions.
Gateway – A device that interconnects networks with different, incompatible
communications protocols.
Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet
CSMA/CD network access method.
Half Duplex - Data transmission that can occur in two directions over a single
line, but only one direction at a time.
Firewall - A firewall is a set of related programs, located at a network gateway
server, that protects the resources of a network from users from other networks.
(The term also implies the security policy that is used with the programs.) An
enterprise with an intranet that allows its workers access to the wider Internet
installs a firewall to prevent outsiders from accessing its own private data
resources and for controlling what outside resources to which its own users have
access.
Hardware - Hardware is the physical aspect of computers, telecommunications,
and other information technology devices. The term arose as a way to distin-
guish the “box” and the electronic circuitry and components of a computer from
the program you put in it to make it do things. The program came to be known
as the software.
Hub - The device that serves as the central location for attaching wires from
workstations. Can be passive, where there is no amplification of the signals; or
active, where the hubs are used like repeaters to provide an extension of the
cable that connects to a workstation.
Basically, a firewall, working closely with a router, examines each network
packet to determine whether to forward it toward its destination.
Firmware - Programming that is inserted into programmable read-only memo-
ry, thus becoming a permanent part of a computing device.
IEEE - The Institute of Electrical and Electronics Engineers. The IEEE
describes itself as “the world's largest technical professional society—promot-
ing the development and application of electrotechnology and allied sciences for
the benefit of humanity, the advancement of the profession, and the well-being
of our members.”
Fragmentation - Breaking a packet into smaller units when transmitting over a
network medium that cannot support the original size of the packet.
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP
network (Internet, UNIX, etc.). For example, after developing the HTML pages
for a website on a local machine, they are typically uploaded to the Web server
using FTP.
The IEEE fosters the development of standards that often become national and
international standards. The organization publishes a number of journals, has
many local chapters, and has several large societies in special areas, such as the
IEEE Computer Society.
FTP includes functions to log onto the network, list directories, and copy files.
It can also convert between the ASCII and EBCDIC character codes. FTP oper-
ations can be performed by typing commands at a command prompt or via an
FTP utility running under a graphical interface such as Windows. FTP transfers
can also be initiated from within a Web browser by entering the URL preceded
with ftp://.
IP Address - In the most widely installed level of the Internet Protocol (Internet
Protocol) today, an IP address is a 32-binary digit number that identifies each
sender or receiver of information that is sent in packets across the Internet.
When you request an HTML page or send e-mail, the Internet Protocol part of
TCP/IP includes your IP address in the message (actually, in each of the pack-
ets if more than one is required) and sends it to the IP address that is obtained
by looking up the domain name in the Uniform Resource Locator you request-
ed or in the e-mail address you're sending a note to. At the other end, the recip-
ient can see the IP address of the Web page requestor or the e-mail sender and
can respond by sending another message using the IP address it received.
Unlike e-mail programs in which graphics and program files have to be
“attached,” FTP is designed to handle binary files directly and does not add the
overhead of encoding and decoding the data.
96
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
IPCONFIG - A utility that provides for querying, defining and managing IP
addresses within a network. A commonly used utility, under Windows NT and
2000, for configuring networks with static IP addresses.
NetBEUI (NetBIOS Extended User Interface) - The transport layer for
NetBIOS. NetBIOS and NetBEUI were originally part of a single protocol suite
that was later separated. NetBIOS sessions can be transported over NetBEUI,
TCP/IP, and SPX/IPX protocols.
IPSec - IPSec (Internet Protocol Security) is a developing standard for security
at the network or packet processing layer of network communication. A big
advantage of IPSec is that security arrangements can be handled without requir-
ing changes to individual user computers.
NetBIOS - The native networking protocol in DOS and Windows networks.
Although originally combined with its transport layer protocol (NetBEUI),
NetBIOS today provides a programming interface for applications at the session
layer (layer 5). NetBIOS can ride over NetBEUI, its native transport, which is
not routable, or over TCP/IP and IPX/SPX, which are routable protocols.
IRQ (Interrupt ReQuest) - A hardware interrupt on a PC. There are 16 IRQ
lines used to signal the CPU that a peripheral event has started or terminated.
Except for PCI devices, two devices cannot use the same line.
NetBIOS computers are identified by a unique 15-character name, and Windows
machines (NetBIOS machines) periodically broadcast their names over the net-
work so that Network Neighborhood can catalog them. For TCP/IP networks,
NetBIOS names are turned into IP addresses via manual configuration in an
LMHOSTS file or a WINS server.
ISP - An ISP (Internet service provider) is a company that provides individuals
and companies access to the Internet and other related services such as website
building and virtual hosting.
LAN - A local area network (LAN) is a group of computers and associated
devices that share a common communications line and typically share the
resources of a single processor or server within a small geographic area (for
example, within an office building).
There are two NetBIOS modes. The Datagram mode is the fastest mode, but
does not guarantee delivery. It uses a self-contained packet with send and
receive name, usually limited to 512 bytes. If the recipient device is not listen-
ing for messages, the datagram is lost. The Session mode establishes a connec-
tion until broken. It guarantees delivery of messages up to 64KB long.
Latency - The time delay between when the first bit of a packet is received and
the last bit is forwarded.
Network - A system that transmits any combination of voice, video, and/or data
between users.
MAC Address - The MAC (Media Access Control) address is a unique number
assigned by the manufacturer to any Ethernet networking device, such as a net-
work adapter, that allows the network to identify it at the hardware level.
Network Mask - also known as the “Subnet Mask.”
NIC (Network Interface Card) - A board installed in a computer system, usual-
ly a PC, to provide network communication capabilities to and from that com-
puter system. Also called an adapter.
Mbps (MegaBits Per Second) - One million bits per second; unit of measure-
ment for data transmission.
mIRC - mIRC runs under Windows and provides a graphical interface for log-
ging onto IRC servers and listing, joining, and leaving channels.
Notebook (PC) - A notebook computer is a battery-powered personal comput-
er generally smaller than a briefcase that can easily be transported and conve-
niently used in temporary spaces such as on airplanes, in libraries, at temporary
offices, and at meetings. A notebook computer, sometimes called a laptop com-
puter, typically weighs less than five pounds and is three inches or less in thick-
ness.
Motherboard - A motherboard is the physical arrangement in a computer that
contains the computer’s basic circuitry and components.
NAT - NAT (Network Address Translation) is the translation of an Internet
Protocol address (IP address) used within one network to a different IP address
known within another network. One network is designated the inside network
and the other is the outside.
Packet Filtering - Discarding unwanted network traffic based on its originating
address or range of addresses or its type (e-mail, file transfer, etc.).
98
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
Partitioning - To divide a resource or application into smaller pieces.
EtherFast® Cable/DSL Routers
nostic tool or debugging feature, especially when fending off an attack. It
enables the administrator to keep close track of switch performance and alter it
if necessary. Port mirroring can be managed locally or remotely.
PCI (Peripheral Component Interconnect) - A peripheral bus commonly used in
PCs, Macintoshes and workstations. It was designed primarily by Intel and first
appeared on PCs in late 1993. PCI provides a high-speed data path between the
CPU and peripheral devices (video, disk, network, etc.). There are typically
three or four PCI slots on the motherboard. In a Pentium PC, there is generally
a mix of PCI and ISA slots or PCI and EISA slots. Early on, the PCI bus was
known as a “local bus.”
PPPoE (Point to Point Protocol over Ethernet) - A method used mostly by DSL
providers for connecting personal computers to a broadband modem for Internet
access. It is similar to how a dial-up connection works but at higher speeds and
quicker access.
PPTP (Point-to-Point Tunneling Protocol) - A protocol (set of communication
rules) that allows corporations to extend their own corporate network through
private “tunnels” over the public Internet. Effectively, a corporation uses a wide-
area network as a single large local area network. A company no longer needs
to lease its own lines for wide-area communication but can securely use the pub-
lic networks. This kind of interconnection is known as a virtual private network
(VPN).
PCI provides “plug and play” capability, automatically configuring the PCI
cards at startup. When PCI is used with the ISA bus, the only thing that is gen-
erally required is to indicate in the CMOS memory which IRQs are already in
use by ISA cards. PCI takes care of the rest.
PCI allows IRQs to be shared, which helps to solve the problem of limited IRQs
available on a PC. For example, if there were only one IRQ left over after ISA
devices were given their required IRQs, all PCI devices could share it. In a PCI-
only machine, there cannot be insufficient IRQs, as all can be shared.
PrintServer - A hardware device that enables a printer to be located anywhere
in the network.
PCMCIA - The PCMCIA (Personal Computer Memory Card International
Association) is an industry group organized in 1989 to promote standards for a
credit card-size memory or I/O device that would fit into a personal computer,
usually a notebook or laptop computer.
RIP (Routing Information Protocol) - A simple routing protocol that is part of
the TCP/IP protocol suite. It determines a route based on the smallest hop count
between source and destination. RIP is a distance vector protocol that routinely
broadcasts routing information to its neighboring routers and is known to waste
bandwidth. AppleTalk, DECnet, TCP/IP, NetWare, and VINES all use incom-
patible versions of RIP.
Ping (Packet INternet Groper) - An Internet utility used to determine whether a
particular IP address is online. It is used to test and debug a network by sending
out a packet and waiting for a response.
RJ-11 (Registered Jack-11) - A telephone connector that holds up to six wires.
The RJ-11 is the common connector used to plug a telephone into a wall.
Plug-and-Play - The ability of a computer system to configure expansion
boards and other devices automatically without requiring the user to turn off the
system during installation.
RJ-45 - A connector similar to a telephone connector that holds up to eight
wires, used for connecting Ethernet devices.
Port - A pathway into and out of the computer or a network device such as a
switch or router. For example, the serial and parallel ports on a personal com-
puter are external sockets for plugging in communications lines, modems, and
printers.
Router - Protocol-dependent device that connects subnetworks together.
Routers are useful in breaking down a very large network into smaller subnet-
works; they introduce longer delays and typically have much lower throughput
rates than bridges.
Port Mirroring - Port mirroring, also known as a roving analysis port, is a
method of monitoring network traffic that forwards a copy of each incoming and
outgoing packet from one port of a network switch to another port where the
packet can be studied. A network administrator uses port mirroring as a diag-
Server - Any computer whose function in a network is to provide user access to
files, printing, communications, and other services.
100
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Software - Instructions for the computer. A series of instructions that performs
a particular task is called a “program.” The two major categories of software are
“system software” and “application software.” System software is made up of
control programs such as the operating system and database management sys-
tem (DBMS). Application software is any program that processes data for the
user.
TCP/IP - Transmission Control Protocol/Internet Protocol (TCP/IP) is the basic
communication language or protocol of the Internet. It can also be used as a
communications protocol in a private network (either an intranet or an extranet).
When you are set up with direct access to the Internet, your computer is provid-
ed with a copy of the TCP/IP program just as every other computer that you may
send messages to or get information from also has a copy of TCP/IP.
A common misconception is that software is data. It is not. Software tells the
hardware how to process the data.
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol
that has no directory or password capability.
SOHO (Small Office/Home Office) - Market segment of professionals who
Throughput - The amount of data moved successfully from one place to anoth-
work at home or in small offices.
er in a given time period.
Static IP Address - A permanent IP address that is assigned to a node in a
TCP/IP network.
Topology - A network’s topology is a logical characterization of how the devices
on the network are connected and the distances between them. The most com-
mon network devices include hubs, switches, routers, and gateways. Most large
networks contain several levels of interconnection, the most important of which
include edge connections, backbone connections, and wide-area connections.
Static Routing - Forwarding data in a network via a fixed path. Static routing
cannot adjust to changing line conditions as can dynamic routing.
Storage - The semi-permanent or permanent holding place for digital data.
TX Rate – Transmission Rate.
STP (Shielded Twisted Pair) - Telephone wire that is wrapped in a metal sheath
to eliminate external interference.
UDP (User Datagram Protocol) - A communications method (protocol) that
offers a limited amount of service when messages are exchanged between com-
puters in a network that uses the Internet Protocol (IP). UDP is an alternative to
the Transmission Control Protocol (TCP) and, together with IP, is sometimes
referred to as UDP/IP. Like the Transmission Control Protocol, UDP uses the
Internet Protocol to actually get a data unit (called a datagram) from one com-
puter to another. Unlike TCP, however, UDP does not provide the service of
dividing a message into packets (datagrams) and reassembling it at the other
end. Specifically, UDP doesn't provide sequencing of the packets that the data
arrives in. This means that the application program that uses UDP must be able
to make sure that the entire message has arrived and is in the right order.
Network applications that want to save processing time because they have very
small data units to exchange (and therefore very little message reassembling to
do) may prefer UDP to TCP.
Subnet Mask - The method used for splitting IP networks into a series of sub-
groups, or subnets. The mask is a binary pattern that is matched up with the IP
address to turn part of the host ID address field into a field for subnets.
Swapping - Replacing one segment of a program in memory with another and
restoring it back to the original when required.
Switch – 1. A data switch connects computing devices to host computers, allow-
ing a large number of devices to share a limited number of ports. 2. A device for
making, breaking, or changing the connections in an electrical circuit.
TCP (Transmission Control Protocol) - A method (protocol) used along with
the Internet Protocol (Internet Protocol) to send data in the form of message
units between computers over the Internet. While IP takes care of handling the
actual delivery of the data, TCP takes care of keeping track of the individual
units of data (called packets) that a message is divided into for efficient routing
through the Internet.
Upgrade - To replace existing software or firmware with a newer version.
Upload - To send a file transmitted over a network. In a communications ses-
sion, upload means transmit, and download means receive.
102
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
URL (Uniform Resource Locator) - The address that defines the route to a file
on the Web or any other Internet facility. URLs are typed into the browser to
access Web pages, and URLs are embedded within the pages themselves to pro-
vide the hypertext links to other pages.
Appendix C: How to Ping Your ISP’s
E-mail & Web Addresses
Virtually all Internet addresses are configured with words or characters (e.g.,
addresses are assigned to IP addresses, which are the true addresses on the
your web browser and you will wind up at the Linksys home page every time.
There are servers that translate the URL to an IP address; this is called Domain
Name System (DNS).
UTP - Unshielded twisted pair is the most common kind of copper telephone
wiring. Twisted pair is the ordinary copper wire that connects home and many
business computers to the telephone company. To reduce crosstalk or electro-
magnetic induction between pairs of wires, two insulated copper wires are twist-
ed around each other. Each signal on twisted pair requires both wires. Since
some telephone sets or desktop locations require multiple connections, twisted
pair is sometimes installed in two or more pairs, all within a single cable.
VLAN (Virtual LAN) - A logical association that allows users to communicate
as if they were physically connected to a single LAN, independent of the actual
physical configuration of the network.
IP and web addresses, however, can sometimes be long and hard to remember.
Because of this, certain ISPs will shorten their server addresses to single words
or codes on their users’ web browser or e-mail configurations. If your ISP’s e-
mail and web server addresses are configured with single words (www, e-mail,
home, pop3, etc.) rather than whole Internet addresses or IP addresses, the
Router may have problems sending or receiving mail and accessing the
Internet. This happens because the Router has not been configured by your ISP
to accept their abbreviated server addresses.
Virtual Server - Multiple servers that appear as one server, or one system
image, to the operating system or for network administration.
Wake-on-LAN - Wake on LAN is a technology that allows a network profes-
sional to remotely power on a computer or to wake it up from sleep mode.
The solution is to determine the true web addresses behind your ISPs code
words. You can determine the IP and web addresses of your ISP’s servers by
“pinging” them.
WAN - A communications network that covers a wide geographic area, such as
a state or country.
WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-
bit shared key algorithm, as described in the IEEE 802.11 standard.
Important: If you don’t have your ISP’s web and e-mail IP
addresses, you must either get them from your ISP or follow these
steps prior to connecting your Cable/DSL Router to your network.
WINIPCFG - Configuration utility based on the Win32 API for querying,
defining, and managing IP addresses within a network. A commonly used util-
ity for configuring networks with static IP addresses.
Workgroup - Two or more individuals that share files and databases.
104
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Step One: Pinging an IP Address
Step Two: Pinging for a Web Address
The first step to determining your ISP’s web and e-mail server address is to
ping its IP address.
While the IP address returned above would work as your e-mail server address,
it may not be permanent. IP addresses change all the time. Web addresses, how-
ever, usually don’t. Because of this, you’re likely to have fewer problems by
configuring your system with web addresses rather than IP addresses. Follow
the instructions below to find the web address assigned to the IP address you
just pinged.
1. Power on the computer and the cable or DSL modem, and restore the
network configuration set by your ISP if you have since changed it.
2. Click Start, then Run, and type command. This will bring up the DOS
window.
1. At the DOS command prompt, type ping -a 24.53.32.4, where 24.53.32.4
is the IP address you just pinged. Information such as the following data
3. At the DOS command prompt, type ping mail (assuming that the loca-
tion for which you’re trying to find an IP address is configured as mail).
Press Enter. Information such as the following data, taken from a ping of
Microsoft Network’s e-mail server, will be displayed.
will be displayed.
C:\>ping -a 24.53.32.4
Pinging mail.msnv3.occa.home.com [24.53.32.4] with
32 bytes of data:
C:\>ping mail
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Pinging mail [24.53.32.4] with 32 bytes of data:
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Ping statistics for 24.53.32.4:
Packets: Sent = 4, Received = 4, Lost = 0 (0%
loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Ping statistics for 24.53.32.4:
Packets: Sent = 4, Received = 4, Lost = 0 (0%
loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Figure C-2
2. Write down the web address returned by the ping command (In the
example in Figure C-2: mail.msnv3.occa.home.com is the web address).
This web address is the web address assigned to the IP address you just
pinged. While the IP address of mail could conceivably change, it is likely
that this web address will not.
Figure C-1
4. Write down the IP address returned by the ping command. (In the
example above: 24.53.32.4.) This IP address is the actual IP address of the
server mail, or any other word or value you have pinged.
3. Replace your ISP’s abbreviated server address with this extended web
address in the corresponding Internet application (web browser, e-mail
application, etc.).
Once you have replaced the brief server address with the true server address,
the Router should have no problem accessing the Internet through that Internet
application.
106
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
6. Find and double-click TCP/IP in the list to the right (see Figure D-2).
Appendix D: Installing the TCP/IP
Protocol
Follow these instructions to install the TCP/IP protocol on one of your PCs only
after a network card has been successfully installed inside the PC. These
instructions are for Windows 95, Windows 98, and Windows Me. For TCP/IP
setup under Windows NT, 2000, and XP, see your Windows documentation or
the Help feature.
1. Click the Start button. Choose Settings and then Control Panel.
Figure D-2
2. Double-click on the Network icon to bring up your Network window.
7. After a few seconds, the main Network window will appear. The TCP/IP
Protocol should now be listed, as shown in Figure D-3.
Select the Configuration tab, as shown in Figure D-1.
Figure D-1
3. Click the Add button.
Figure D-3
4. Double-click on Protocol.
8. Click the OK button. Windows may ask for original Windows installation
files. Supply them as needed, e.g., c:\windows\options\cabs, D:\win98,
D:\win95.
5. Highlight Microsoft under the list of manufacturers.
9. Windows will ask you to restart the PC. Click the Yes button.
The TCP/IP installation is now complete.
108
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Crimping Your Own Network Cables
Appendix E: Twisted-Pair Cabling
There are different grades, or “categories,” of twisted-pair cabling. Category 5
is the most reliable and most highly recommended. Category 3 is a good sec-
ond choice. Straight-through cables are used for connecting computers to a
hub. Crossover cables are used for connecting a hub to another hub (there is an
exception: some hubs have a built-in uplink port that is crossed internally; this
allows you to link or connect hubs together with a straight-through cable
instead).
• Straight-Through Cabling
You can buy pre-made Category 5 cables, or cut and crimp your own. Category
5 cables can be purchased or crimped
as either straight-through or crossover.
Inside a Category 5 cable are eight
thin, color-coded wires inside that run
from one end of the cable to the other.
All eight wires are used. In a straight-
through cable, wires 1, 2, 3, and 6 at
one end of the cable are also wires 1,
2, 3, and 6 at the other end. In a
crossover cable, the order of the wires
change from one end to the other: wire
1 becomes 3, and 2 becomes 6. See
Figures E-3 and E-4 on the next page
for more detailed information on
Figure E-3
• Cross-Over Cabling
straight-through
cabling.
and
crossover
To determine which
wire is wire number 1,
Figure E-1
hold the cable so that the
end of the plastic RJ-45 tip
(the part that goes into a wall jack first) is facing away
from you. Face the clip down so that the copper side faces
up (the springy clip will now be parallel to the floor).
When looking down on the copper side, wire 1 will be on
the far left.
Figure E-4
Figure E-2
110
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
3. Write down the Adapter Address as shown on your computer screen (see
Figure F-3). This is the MAC address for your Ethernet adapter and will be
shown as a series of numbers and letters.
Appendix F: Finding the MAC
Address and IP Address for Your
Ethernet Adapter
The MAC address/Adapter Address is what you will use for MAC Address
Cloning or MAC Filtering.
This section describes how to find the MAC address for your Ethernet adapter
to do either MAC Filtering or MAC Address Cloning for the Router and ISP.
You can also find the IP address of your computer’s Ethernet adapter. The IP
address is used for filtering, forwarding, and DMZ. Follow the steps in this
appendix to find the MAC address or IP address for your adapter in Windows
95, 98, Me, NT, 2000, and XP.
For Windows 95, 98, and Me:
1. Click on Start and Run. In the Open field, enter winipcfg, as shown in
Figure F-1. Then press the Enter key or the OK button.
Figure F-3
The example in Figure F-3 shows the IP address of your Ethernet adapter
as 192.168.1.100. Your computer may show something different.
Note: The MAC address is also called the Adapter
Address.
For Windows NT, 2000, and XP:
Figure F-1
The following steps show an alternative way of obtaining the MAC address and
IP address for your Ethernet adapter.
2. When the IP Configuration window appears, select the Ethernet adapter
you are using to connect to the Router via a CAT 5 Ethernet cable, as shown
in Figure F-2.
1. Click on Start and Run. In the Open field, enter cmd, as shown in Figure
F-4. Press the Enter key or click the OK button.
Figure F-4
Figure F-2
112
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
2. In the command prompt, enter ipconfig /all. Then press the Enter key.
When entering the information using the Router’s web-based utility, you will
type the 12-digit MAC address in this format, XXXXXXXXXXXX without
the hyphens for MAC Filtering. See Figure F-6.
Figure F-5
Figure F-6
3. Write down the Physical Address as shown on your computer screen
(Figure F-5); it is the MAC address for your Ethernet adapter. This will
appear as a series of letters and numbers.
When entering information for MAC Address Cloning, type the 12-digit MAC
address (see Figure F-7).
The MAC address/Physical Address is what you will use for MAC Address
Cloning or MAC Filtering.
Note: The MAC address is also called the Physical
Address.
The example in Figure F-5 shows the IP address of your Ethernet adapter
as 192.168.1.100. Your computer may show something different.
Figure F-7
114
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
3. From the
®
Appendix G: Setting Up AOL
Setup screen
that appears,
shown
in
Broadband Cable & DSL
Figure G-3,
s e l e c t
Obtain an
IP automat-
ically from
This document provides instructions for setting up the Router using firmware
version 1.43 or above to work with AOL Broadband via a Cable or DSL con-
nection. This Router's AOL Parental Controls feature is available for AOL cus-
tomers in the US only. Please follow the instructions in the appropriate section
below to configure for AOL Broadband for the type of broadband connection
the
WAN
Connection
Type drop-
down menu.
Then, click
the Security
tab.
you have.
Note: You must install AOL 7.0 or above to all computers
using AOL Services. Those with earlier versions of AOL
can find details at AOL Keyword: Linksys Setup.
Note: Some of the screens in this section may look
slightly different than what appears on your screen.
Figure G-3
AOL Broadband via Cable
4. Select Enable for
A O L P a r e n t a l
Controls from the
Security tab, shown
in Figure G-4, and
click the OK button
on the screen that
appears. Enabling
this will disable all
options under the
1. Open your web browser. Enter
http://192.168.1.1 in the web
browser’s Address field, as shown in
Figure G-1, and press the Enter key.
Figure G-1
2. A password request page, shown in Figure G-2 will appear. (Windows XP
users will see a Connect to 192.168.1.1 window slightly different from that
shown). Leave the User Name field blank, and enter admin in the Password
field. Then click
the OK button. Ro
Advanced
except
tab
MAC
Address cloning.
Then, click the OK
button to save these
settings. Click the
X button on the top
right side of the win-
dow to close it.
Figure G-4
Note: AOL Parental Controls are available
to AOL customers in the Unites States Only.
Figure G-2
116
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
AOL Broadband via DSL
Appendix H: 4-Port Router
Specifications
1. Open your web browser. Enter
http://192.168.1.1 in the web
browser’s Address field, as shown in
Figure G-5, and press the Enter key.
Figure G-5
Model Number
Standards
Protocol
Ports
BEFSR41 ver. 2
IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX)
CSMA/CD
2. A password request page, shown in
Figure G-6 will appear. (Windows XP
users will see
a
Connect to
192.168.1.1 window slightly different
from that shown). Leave the User
Name field blank, and enter admin in
the Password field. Then click the
OK button.
LAN:
Four 10/100 RJ-45 switched ports (and shared
uplink)
WAN:
One 10Base-T Ethernet RJ-45 port for the cable
or DSL modem
Figure G-6
Speed
3. From the Setup screen that appears, shown in Figure G-7, select PPPoE
from the WAN Connection Type drop-down menu. Enter america online
for the User Name. In the password field, multiple asterisks will appear.
Keep these settings and click the Apply button to save them. Click the X
button on the top right side of the window to close it.
LAN:
WAN:
10/100Mbps
10Mbps
Cabling Type
10BaseT:
100BaseTX:
Topology
LED Indicators
LAN:
UTP Category 3 or better
UTP Category 5 or better
Star
Power
Link/Act, Full/Col, 100
Link, Act, Diag
WAN:
4-Port Environmental Specifications
Dimensions
7.31" x 6.16" x 1.88"
(186 mm x 154 mm x 48 mm)
13.4 oz. (0.42 kg)
External, 9V AC, 1 Amp
FCC Class B, CE Mark
Unit Weight
Power Input
Certifications
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -20°C to 70°C (-4°F to 158°F)
Operating Humidity
Storage Humidity
10% to 85%, Non-condensing
5% to 90%, Non-condensing
Figure G-7
118
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Appendix I: 1-Port Router
Specifications
Appendix J: 3-Port Router
Specifications
1-Port Router Specifications
Model Number
Standards
BEFSRU31
Model Number
Standards
Protocol
Ports
BEFSR11, ver. 2
IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX)
CSMA/CD
IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX),
USB Specification 1.0 & 1.1
CSMA/CD
Protocol
Ports
LAN:
Three 10/100 RJ-45 Switched ports (and shared
uplink), One USB port
One 10Base-T Ethernet RJ-45 port for the cable
or DSL modem
LAN:
WAN:
Speed
WAN:
One 10BaseT/100BaseTX RJ-45 port
One10BaseT Broadband Uplink port
WAN:
10Mbps (10BaseT Ethernet)
10Mbps (10BaseT Ethernet) or
100Mbps (100BaseTX Fast Ethernet)
Speed
LAN:
LAN (Ethernet):
WAN (Ethernet):
USB:
Cabling Type
10BaseT:
100BaseTX:
USB:
Topology
LED Indicators
LAN:
10/100Mbps
10Mbps
Up to 12Mbps
Cabling Type
10BaseT:
100BaseTX:
Topology
LED Indicators
LAN:
UTP Category 3 or better
UTP Category 5 or better
Star
Power
Link/Act, Full/Col, 100
Link, Act, Diag
UTP Category 3 or better
UTP Category 5 or better
Standard USB cable
Star
WAN:
Power
Link/Act, Full/Col, 100
Link, Act, Diag
USB
1-Port Environmental Specifications
WAN:
USB:
Dimensions
7.31" x 6.16" x 1.88"
(186 mm x 154 mm x 48 mm)
12.6 oz. (0.35 kg)
External, 7.5V DC, 700 mA
FCC Class B, CE Mark
3-Port Environmental Specifications
Unit Weight
Power Input
Certifications
Dimensions
7.31" x 6.16" x 1.88"
(186 mm x 154 mm x 48 mm)
13.4 oz. (0.42 kg)
External, 9V AC, 1 Amp
FCC Class B, CE Mark
Unit Weight
Power Input
Certifications
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -20°C to 70°C (-4°F to 158°F)
Operating Humidity
Storage Humidity
10% to 85%, Non-condensing
5% to 90%, Non-condensing
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -20°C to 70°C (-4°F to 158°F)
Operating Humidity
Storage Humidity
10% to 85%, Non-condensing
5% to 90%, Non-condensing
120
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband™ Series
EtherFast® Cable/DSL Routers
Appendix K: Warranty Information
BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE
FROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING.
RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF
PURCHASE.
Appendix L: Contact Information
For help with the installation or operation of your Instant Broadband EtherFast
Cable/DSL Router, contact Linksys Technical Support at one of the phone
numbers or Internet addresses below.
Sales Information
Technical Support
RMA Issues
Fax
800-546-5797 (1-800-LINKSYS)
800-326-7114
949-271-5461
IN NO EVENT SHALL LINKSYS’S LIABILITY EXCEED THE PRICE
PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCI-
DENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS
DOCUMENTATION. LINKSYS DOES NOT OFFER REFUNDS FOR ANY
PRODUCT.
949-265-6655
Email
Web site
FTP site
LINKSYS OFFERS CROSS SHIPMENTS, A FASTER PROCESS FOR PRO-
CESSING AND RECEIVING YOUR REPLACEMENT. LINKSYS PAYS
FOR UPS GROUND ONLY. ALL CUSTOMERS LOCATED OUTSIDE OF
THE UNITED STATES OF AMERICA AND CANADA SHALL BE HELD
RESPONSIBLE FOR SHIPPING AND HANDLING CHARGES. PLEASE
CALL LINKSYS FOR MORE DETAILS.
122
123
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 2002 Linksys, All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|