Owner’s Manual
Installation and Operation
Models:
BE-36-C
BE-36-CIPI
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
WARNING
WARNING: If the information in
these instructions is not followed
exactly, a fire or explosion may result
causing property damage, personal
injury, or death.
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot during
operation and cool down.
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
•
Keep children away.
•
CAREFULLY SUPERVISE children in same room as
appliance.
•
•
Alert children and adults to hazards of high temperatures.
• What to do if you smell gas
Do NOT operate with protective barriers open or
removed.
- Do not try to light any appliance
•
Keep clothing, furniture, draperies and other
combustibles away.
- Do not touch any electrical switch. Do not
use any phone in your building.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
or gas fitter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory-trained
professionals, or technicians supervised by an NFI
certified professional.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
1
- Table of Contents -
Section 1: Listing and Code Approvals
A. Appliance Certification................................... 4
Section 9:
Gas Information
A. Fuel Conversions...................................... 35
B. Gas Pressures.......................................... 35
C. Gas Connection........................................ 35
B. Glass Specifications...................................... 4
C. BTU Specifications ........................................ 4
D. High Altitude Installations .............................. 4
E. Non-Combustible Materials Specification...... 4
F. Combustible Materials Specification.............. 4
G. Requirements for the Commonwealth
Section 10: Electrical Information
A. Recommendation for Wire........................ 37
B. Connecting to the Appliance..................... 37
C. Standing Pilot Ignition System Wiring....... 38
D. Intellifire Ignition System Wiring................ 38
E. Junction Box Installation........................... 39
F. Wall Switch Installation for Fan................. 39
of Massachusetts........................................... 5
Section 2: Getting Started
A. Design and Installation Considerations......... 6
B. Tools and Supplies Needed........................... 6
C. Inspect Appliance and Components.............. 6
Section 11: Finishing
A. Mantel Projections .................................... 40
Section 3: Framing and Clearances
B. Facing Material ......................................... 40
A. Selecting Appliance Location......................... 7
B. Constructing the Appliance Chase ................ 8
C. Clearances .................................................... 8
D. Mantel Projections......................................... 9
Section 12: Appliance Setup
A. Remove Shipping Materials...................... 41
B. Clean the Appliance.................................. 41
C. Accessories .............................................. 41
D. Positioning the Logs ................................. 42
E. Glass Assembly ........................................ 43
F. Grilles and Trim......................................... 43
Section 4: Termination Locations
A. Vent Termination Minimum Clearances....... 10
Î
Section 5: Vent Information and Diagrams
A. Vent Table Key............................................. 12
B. Use of Elbows.............................................. 12
C. Measuring Standards .................................. 12
D. Use of Flex Vent .......................................... 13
E. Vent Diagrams............................................. 14
Section 13: Operating Instructions
A. Before Lighting Appliance......................... 44
B. Lighting Appliance..................................... 45
C. After Appliance is Lit ................................. 47
D. Frequently Asked Questions..................... 47
Section 6: Vent Clearances and Framing
Section 14: Troubleshooting
A. Pipe Clearances to Combustibles ............... 22
B. Wall Penetration Framing............................ 22
C. Vertical Penetration Framing....................... 23
A. Standing Pilot Ignition System.................. 49
B. Intellifire Ignition System........................... 50
Î
Section 15: Maintaining and Servicing Appliance........... 52
Section 7: Appliance Preparation
A. Top Vent....................................................... 24
B. Rear Vent..................................................... 25
C. Securing and Leveling the Appliance .......... 26
Section 16: Reference Materials
A. Appliance Dimension Diagram ................. 54
B. Vent Components Diagrams..................... 55
C. Service Parts ............................................ 60
D. Warranty ................................................... 65
E. Contact Information .................................. 66
Î
Section 8: Installing Vent Pipe
A. Assembly of Vent Sections for DVP Pipes .. 27
B. Disassembly of Vent Sections..................... 29
C. Installing Heat Shield and
Horizontal Termination Cap ........................ 31
D. Installing Roof Flashing and Vertical
Î
Termination Cap .......................................... 33
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Listing and Code Approvals
1
A. Appliance Certification
C. BTU Specifications
Maximum Input Orifice Size
Models
(U.S. or Canada)
MODELS: BE-36-C, BE-36-CIPI
BTU/h
(DMS)
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
U.S.
(0-2000 ft.)
19,000
#45
BE-36-C (NG)
BE-36-CIPI (NG)
Canada
(2000-4500 ft.)
STANDARD: ANSI Z21.88-2002 • CSA2.33-M02 • UL307B
17,100
18,500
16,650
#46
#55
#56
U.S.
(0-2000 ft.)
BE-36-C (LP)
BE-36-CIPI (LP)
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burn-
ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas FiredAppliances for Use
at High Altitudes”.
Canada
(2000-4500 ft.)
D. High Altitude Installations
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental
room heat or as a decorative appliance. It should not be fac-
tored as primary heat in residential heating calculations.
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above
a 2000 foot elevation in the U.S.A., or 10% for elevations
between 2000 and 4500 feet in Canada. If the heating
value of the gas has been reduced, these rules do not
apply. To identify the proper orifice size, check with the
local gas utility.
B. Glass Specifications
Hearth & Home Technologies appliances manufactured with
tempered glass may be installed in hazardous locations
such as bathtub enclosures as defined by the Consumer
Product Safety Commission (CPSC). The tempered glass
has been tested and certified to the requirements of ANSI
Z97.1 and CPSC 16 CFR 1202 (Safety Glazing Certification
Council SGCC# 1595 and 1597. Architectural Testing, Inc.
Reports 02-31919.01 and 02-31917.01).
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
This statement is in compliance with CPSC 16 CFR
Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
WARNING
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750º C, shall be considered
non-combustible materials.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper,
plant fibers, plastics, or other material that can ignite and
burn, whether flame proofed or not, or whether plastered or
unplastered shall be considered combustible materials.
Heat & Glo Quality Systems
registered by SGS ICS
4
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection
NOTE: The following requirements reference various
Massachusetts and national codes not contained in this
document.
The state or local gas inspector of the side wall horizontally
vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes
carbon monoxide detectors and signage installed in
accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
G. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where
the side wall exhaust vent termination is less than seven
(7) feet above finished grade in the area of the venting,
including but not limited to decks and porches, the following
requirements shall be satisfied:
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas
fueled equipment installed in a room or structure
separate from the dwelling, building or structure used
in whole or in part for residential purposes.
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gasfitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the
floor level where the gas equipment is to be installed. In
addition, the installing plumber or gasfitter shall observe
that a battery operated or hard wired carbon monoxide
detector with an alarm is installed on each additional level
of the dwelling, building or structure served by the side
wall horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
In the event that the side wall horizontally vented gas fueled
equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery
back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply with
the above requirements; provided, however, that during
said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide
the parts for venting the flue gases, but identifies “special
venting systems”, the following requirements shall be
satisfied by the manufacturer:
Approved Carbon Monoxide Detectors
• The referenced “special venting system” instructions
shall be included with the appliance or equipment instal-
lation instructions; and
Each carbon monoxide detector as required in accordance
with the above provisions shall comply with NFPA720 and
be ANSI/UL 2034 listed and IAS certified.
• The “special venting systems” shall be ProductApproved
by the Board, and the instructions for that system shall in-
clude a parts list and detailed installation instructions.
Signage
A metal or plastic identification plate shall be permanently
mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with
the exhaust vent terminal for the horizontally vented gas
fueled heating appliance or equipment. The sign shall
read, in print size no less than one-half (1/2) inch in size,
“GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS”.
A copy of all installation instructions for all Product Ap-
proved side wall horizontally vented gas fueled equipment,
all venting instructions, all parts lists for venting instruc-
tions, and/or all venting design instructions shall remain
with the appliance or equipment at the completion of the
installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Getting Started
2
A. Design and Installation Considerations
C. Inspect Appliance and Components
Hearth & Home Technologies direct vent gas appliances are
designed to operate with all combustion air siphoned from
outside of the building and all exhaust gases expelled to the
outside. No additional outside air source is required.
WARNING
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult local building, fire officials or authorities having
jurisdiction about restrictions, installation inspection, and
permits.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and trim doors are shipped
in separate packages.
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• The gas logs may be packaged separately and must
be field installed.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Electrical wiring.
• Read all of the instructions before starting the in-
stallation. Follow these instructions carefully dur-
ing the installation to ensure maximum safety and
benefit.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
WARNING
WARNING
Keep appliance dry.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
•
•
Mold or rust may cause odors.
Water may damage controls.
•
Installation and use of any damaged appliance or vent
system component.
•
•
Modification of the appliance or vent system.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Installation other than as instructed by Hearth & Home
Technologies.
•
•
Improper positioning of the gas logs or the glass door.
Reciprocating saw
Pliers
Framing material
Hi temp caulking material
Gloves
Installation and/or use of any component part not
approved by Hearth & Home Technologies.
Any such action may cause a fire hazard.
Hammer
Phillips screwdriver
Framing square
Flat blade screwdriver Electric drill and bits (1/4 in.)
Plumb line
Level
Safety glasses
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Voltmeter
Manometer
Tape measure
Noncorrosive leak check solution
One 1/4 inch female connection (for optional fan).
6
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Framing and Clearances
3
NOTE:
WARNING
• Illustrations reflect typical installations and are FOR DESIGN
PURPOSES ONLY.
Fire Risk
Provide adequate clearance:
• Around air openings
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
• To combustibles
• For service access
preference.
Locate appliance away from traffic areas.
A. Selecting Appliance Location
When selecting a location for your appliance it is important to
consider the required clearances to walls (see Figure 3.1).
NOTE: For actual appliance dimensions refer to Sec-
tion 16.
A
E
F
D
C
In addition to these framing dimensions, also reference the following sections:
•
•
Clearances and Mantel Projections (Section 3.C and 3.D)
Vent Clearances and Framing (Section 6).
H
B
I
G
Models
BE-36-C
BE-36-CIPI
A
B
C
D
E
1
F
G
H
I
Inches
41-1/2
1054
37
58-3/4
1492
1/2 48-1/2 68-1/4 16-1/4
13 1232 1734 413
See Section D for
Alcove Installation
Millimeters
940
25
Figure 3.1 Appliance Locations
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Gas line holes and other openings should be caulked with
high temp caulk or stuffed with unfaced insulation. If the
appliance is being installed on a cement slab, a layer of
plywood may be placed underneath to prevent conducting
cold up into the room.
B. Constructing the Appliance Chase
A chase is a vertical boxlike structure built to enclose the
gas appliance and/or its vent system. Vertical vents that run
on the outside of a building may be, but are not required
to be, installed inside a chase.
C. Clearances
Construction of the chase may vary with the type of building.
These instructions are not substitutes for the requirements
of local building codes. Local building codes MUST be
checked.
WARNING
Fire Risk.
Odor Risk.
Chases should be constructed in the manner of all outside
walls of the home to prevent cold air drafting problems.
The chase should not break the outside building envelope
in any manner.
• Install appliance on hard metal or wood surfaces
extending full width and depth of appliance.
• Do NOT install appliance directly on carpeting,
vinyl, tile or any combustible material other than
wood.
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
WARNING
Fire Risk.
• Construct chase to all clearance specifications
in manual.
• Locate and install appliance to all clearance
specifications in manual
To further prevent drafts, the wall shield and ceiling firestops
should be caulked with high temperature caulk to seal gaps.
FROM TOP
OF HOOD
TO CEILING
A
E
F
H
B
G
J
C
D
I
A
B
C
D
E
F
G
H
I
J
DVP Pipe SL Pipe
DVP Pipe SL Pipe
Rough
Opening
(Height)
Rough
Opening
(Width)
Non-
Combustible
Floor
Models
Clearance
to Ceiling
Combustible Behind
Sides of
Front of
Rough
Opening Opening
(Width)
Rough
Rough
Opening Opening
(Depth) (Depth)
Rough
Flooring
Appliance Appliance Appliance
(Width)
in.
10
8-5/8
219
33
27-1/2 16-1/4
699 413
37
31
0
0
0
0
1/2
13
1/2
13
36
BE-36-C
BE-36-CIPI
mm
254
838
940
787
915
Figure 3.2 Clearances to Combustibles
8
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Mantel Projections
Note: Clearance
from opening to
perpendicular wall.
1
”
”
2
Figure 3.4 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
Figure 3.3 Clearances to Mantels or other Combustibles
above Appliance
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Termination Locations
4
A. Vent Termination Minimum Clearances
HORIZONTAL
OVERHANG
WARNING
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
Fire Risk.
LOWEST
DISCHARGE
OPENING
Explosion Risk.
GAS DIRECT VENT
TERMINATION CAP
Maintain vent clearance to combustibles as
specified.
X
•
Do not pack air space with insulation or
other materials.
12
ROOF PITCH
IS X/ 12
Failure to keep insulation or other materials
away from vent pipe may cause fire.
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Measure vertical clearances from this surface.
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12.................................................1.25*
Over 7/12 to 8/12.................................................1.5*
Over 8/12 to 9/12.................................................2.0*
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
* 3 foot minimum in snow regions
Î
Measure horizontal clearances from this surface.
Figure 4.2 Minimum Height from Roof to Lowest Discharge
Opening
(See Figure 4.4 for specific clearances)
Figure 4.2 specifies minimum vent heights for various
pitched roofs.
Figure 4.1
GAS, WOOD OR FUEL
OIL TERMINATION
B
GAS
TERMINATION
C
A
Gas
Termination
Wood & Fuel Oil
Termination
Comments
A
B
C
6 in.
20 in.
18 in.
20 in. min.
24 in. min.
18 in.
Horizontal distance between terminations
Distance to perpendicular wall
Vertical distance between terminations
Î
Figure 4.3 Multiple Vertical Termination
10
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
M
N
P
R
Q
(See Note 2)
V
T
S
S
Electrical
Service
V
V
D*
V
= VENT TERMINAL
X
= AIR SUPPLY INLET
= AREA WHERE TERMINAL IS NOT PERMITTED
V
K
= 3 ft. (U.S.A.)
A
B
= 12 inches...............clearances above grade, veranda,
6 ft. (Canada)...........clearance to a mechanical
(powered) air supply inlet
(See Note 1)
porch, deck or balcony
= 12 inches...............clearances to window or door
that may be opened, or to perma-
L** = 7 ft...........................clearance above paved
(See Note 1)
sidewalk or a paved driveway
located on public property
nently closed window. (Glass)
D*
= 18 inches...............vertical clearance to unventilated
soffit or to ventilated soffit located
above the terminal
M*** = 18 inches.................clearance under veranda, porch,
deck, balcony or overhang
42 inches ................vinyl
*30 inches..............for vinyl clad soffits and below
S = 6 inches ...................clearance from sides of elec-
electrical service
(See Note 5)
trical service
F
=
9 inches................clearance to outside corner
T
= 12 inches ..................clearance above electrical
G
H
= 6 inches.................clearance to inside corner
(See Note 5)
service
= 3 ft. (Canada)........not to be installed above a gas
meter/regulator assembly within 3
Alcove Applications
feet (90 cm) horizontally from the
center-line of the regulator
N
= 6 inches ..................non-vinyl sidewalls
12 inches ................vinyl sidewalls
P
= 8 ft.
Î
I
= 3 ft.........................clearance to gas service regulator
vent outlet
QMIN
3 feet
6 feet
9 feet
12 feet
RMAX
J
= 9 inches (U.S.A.)
1 cap
2 caps
3 caps
4 caps
2 x Q ACTUAL
1 x Q ACTUAL
2/3 x Q ACTUAL
1/2 x Q ACTUAL
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
NOTE 3: Local codes or regulations may require different
clearances.
NOTE 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor, or meets Note 2.
NOTE 5: Location of the vent termination must not interfere with
NOTE 1: On private property where termination is less than 7 feet above
a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
access to the electrical service.
WARNING: In the U.S: Vent system termination is NOT permitted in
screened porches. You must follow side wall, overhang and ground
clearances as stated in the instructions.
NOTE 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow all side walls, overhang
and ground clearances as stated in the instructions.
Hearth & Home Technologies assumes no responsibility for the
improper performance of the appliance when the venting system
does not meet these requirements.
Figure 4.4 Minimum Clearances for Termination
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Vent Information and Diagrams
5
A. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
Description
First section (closest to appliance) of vertical length
Vertical
V1
Second section of vertical length
V2
H1
H2
First section (closest to appliance) of horizontal length
Second section of horizontal length
8-1/2 in.
WARNING
Horizontal
Fire Hazard.
Figure 5.1
Explosion Risk.
Asphyxiation Risk.
Do NOT connect this gas appliance to a chimney
flue serving a separate solid-fuel or gas burning
appliance.
C. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
1. Pipe measurements are shown using the effective length
of pipe (see Figure 5.2).
May impair safe operation of this appliance or
other appliances connected to the flue.
2. Measurements are made from the appliance outer wrap,
not from the standoffs.
3. Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
4.1).
B. Use of Elbows
4. Vertical terminations are measured to bottom of termina-
tion cap.
CAUTION
ALL vent configuration specifications MUST be followed.
• This product is tested and listed to these specifications.
5. Horizontal pipe installed level with no rise.
• Appliance performance will suffer if specifications are
not followed.
Effective Length
Pipe
Inches
Millimeters
Diagonal runs have both vertical and horizontal vent
aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 5.1).
Two 450 elbows may be used in place of one 900 elbow.
On 450 runs, one foot of diagonal is equal to 8.5 inches
horizontal run and 8.5 inches vertical run. A length of
straight pipe is allowed between two 450 elbows (see
Figure 5.1).
DVP4
4
102
DVP6
6
12
152
305
DVP12
DVP24
DVP36
DVP48
DVP6A
Effective
Height/Length
24
610
36
914
48
1219
76 to 152
3 to 6
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
Figure 5.2 DVP Pipe Effective Length
12
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Use of Flex Vent
The flex vent must be supported with
the spacing between support intervals
not exceeding 4 feet, with no more than
½ inch sag between supports.
TERMINATION
CAP
3 in. CLEARANCE
A support is required at each change
in venting direction, and in any location
where it is necessary to maintain the
necessary clearance to combustibles.
A simple “up and out” installation
(Figure 5.3) requires only enough
support to maintain the necessary
clearance to combustibles. However,
the vent attachment point and the
firestop location are considered to be
supports.
FLEX-VENT
1 in.
CLEARANCE
Figure 5.3
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
13
E. Vent Diagrams
WARNING
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling firestops.
•
•
ALWAYS maintain specified clearances around venting and firestop systems.
Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away from vent pipe may cause fire.
1. Top Vent - Horizontal Termination
H1 Maximum
BE-36-C NG BE-36-C LP
1-1/2 ft. 457 mm 1-1/2 ft. 457 mm
V Minimum
One Elbow
90 Elbow Only
1/2 ft. 152 mm
1-1/2 ft. 457 mm
2-1/2 ft. 762 mm
Note: Use SL D- Series
components only.
2 ft.
3 ft.
5 ft.
7 ft.
15 ft.
610 mm 1-1/2 ft. 457 mm
914 mm
1.5 m
3 ft.
5 ft.
914 mm
1.5 m
H1
V1
3-1/2 ft.
4-1/2 ft.
1.1 m
1.4 m
2.1 m
7 ft.
2.1 m
4.6 m
15 ft.
4.6 m
H1 MAX. =15 FT (4.6 m)
V1 + H1 MAX. = 40 FT (12.2 m)
NOTE: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
Figure 5.4
H1 + H2 Maximum
V Minimum
Two Elbows
BE-36-C NG
BE-36-C LP
90 Elbow Only
1/2 ft. 152 mm
1-1/2 ft. 457 mm
2-1/2 ft. 762 mm
1/2 ft.
1 ft.
152 mm
305 mm
610 mm
1.2 m
1/2 ft.
152 mm
152 mm
610 mm
1.2 m
Note: Use SL D- Series
components only.
1/2 ft.
2 ft.
2 ft.
4 ft.
4 ft.
3-1/2 ft.
4-1/2 ft.
1.1 m
1.4 m
6 ft.
1.8 m
6 ft.
1.8 m
14 ft.
4.3 m
14 ft.
4.3 m
H1 + H2 MAX. =14 FT (4.3 m)
V1 + H1 + H2 MAX. = 40 FT (12.2 m)
H1
NOTE: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
H2
V1
Figure 5.5
14
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Top Vent - Horizontal Termination - (continued)
Three Elbows
H1 Maximum
V Minimum
H1 + H2 Maximum
BE-36-C NG & LP
BE-36-C NG
610 mm
BE-36-C LP
610 mm
90 Elbow Only
1/2 ft.
1-1/2 ft.
1-1/2 ft.
3 ft.
457 mm
457 mm
914 mm
1.5 m
2 ft.
4 ft.
2 ft.
3 ft.
152 mm
457 mm
762 mm
1.1 m
1.2 m
1.8 m
3.0 m
4.3 m
4.3 m
914 mm
1.8 m
3.0 m
4.3 m
4.3 m
1-1/2 ft.
2-1/2 ft.
3-1/2 ft.
4-1/2 ft.
6 ft.
6 ft.
5 ft.
10 ft.
14 ft.
14 ft.
10 ft.
14 ft.
14 ft.
7 ft.
2.1 m
1.4 m
15 ft.
4.6 m
H1 + H2 MAX. =14 FT (4.3 m)
V1 + V2 + H1 + H2 MAX. = 40 FT (12.2 m)
NOTE: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
Note: Use SL D- Series
components only.
H2
H1
V2
V1
Figure 5.6
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Baffles are recommended for these vertically terminated
products which have excessive draft. Baffles compensate
for high draft, restore visual flame height, and limit exces-
sive cooling resulting from too much secondary air. Refer
to the allowable vent configurations in the model specific
installer’s guide for recommended use of this baffle.
Top Vent - Vertical Termination
No Elbows
V1 = 44 ft. Max. (13.4 m)
NOTE: For vertical venting over 20 feet an extended vertical
baffle is recommended for improved flame appearance.
Baffle Instruction
1. Install the baffle over the center of the exhaust outlet in
the firebox (see Figure 5.8).
2. Center the exhaust opening in the open end of the
baffle, and secure through the slots on the baffle with
the 2-1/4 in. self tapping screws provided.
Note: Use SL D- Series
components only.
VIEW FROM
UNDERNEATH
CAP
BAFFLE
FRONT
OF UNIT
FIREBOX
BACK
V1
SIDE VIEW
EXHAUST
BAFFLE
FIREBOX
BACK
Figure 5.8
Figure 5.7
16
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Top Vent - Vertical Termination - (continued)
H1 Maximum
BE-36-C NG BE-36-C LP
1-1/2 ft. 457 mm 1-1/2 ft. 457 mm
Two Elbows
V Minimum
90 Elbow Only
1/2 ft. 152 mm
1-1/2 ft. 457 mm
2-1/2 ft. 762 mm
2 ft.
3 ft.
5 ft.
7 ft.
15 ft.
610 mm 1-1/2 ft. 457 mm
H1
914 mm
1.5 m
3 ft.
5 ft.
914 mm
1.5 m
V2
3-1/2 ft.
4-1/2 ft.
1.1 m
1.4 m
2.1 m
7 ft.
2.1 m
4.6 m
15 ft.
4.6 m
V1
H1 MAX. =15 FT (4.6 m)
V1 + V2 + H1 MAX. = 40 FT (12.2 m)
NOTE: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
Note: Use SL D- Series
components only.
Figure 5.9
H1 + H2 Maximum
V Minimum
BE-36-C NG
BE-36-C LP
Three Elbows
90 Elbow Only
1/2 ft. 152 mm
1-1/2 ft. 457 mm
2-1/2 ft. 762 mm
1/2 ft.
1 ft.
152 mm
305 mm
610 mm
1.2 m
1/2 ft.
152 mm
152 mm
610 mm
1.2 m
1/2 ft.
2 ft.
2 ft.
4 ft.
4 ft.
3-1/2 ft.
4-1/2 ft.
1.1 m
1.4 m
6 ft.
1.8 m
6 ft.
1.8 m
V2
14 ft.
4.3 m
14 ft.
4.3 m
H1 + H2 MAX. =14 FT (4.3 m)
V1 + V2 + H1 + H2 MAX. = 40 FT (12.2 m)
H1
V1
H2
Note: Use SL D- Series
components only.
Figure 5.10
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
17
3. Rear Vent - Horizontal Termination
No Elbows
H1 = 28 in. (711 mm) Maximum
Note: Use DVP Series
components only.
Figure 5.11
Rear Vent - Horizontal Termination
One 45º Elbow
H1 = 9 in. (229 mm) Maximum
Note: Use DVP Series
components only.
Figure 5.12
18
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Rear Vent - Horizontal Termination- (continued)
Two elbows
V Minimum
0 ft. 0 mm
H1 Maximum
H1 + H2 Maximum
1-1/2 ft. 457 mm 2-1/2 ft. 762 mm
Note: Use DVP Series
1 ft.
2 ft.
3 ft.
305 mm 3-1/2 ft.
762 mm 5-1/2 ft.
1.1 m
1.7 m
2.3 m
6-1/2 ft.
10-1/2 ft.
14 ft.
2 m
components only.
3.2 m
4.3 m
1.1 m
7-1/2 ft.
H1 + H2 MAX. =14 FT (4.3 m)
V1 + H1 + H2 MAX. = 40 FT (12.2 m)
Figure 5.13
V Minimum
H1 Maximum
H1 + H2 + H3 Maximum
3. Rear Vent - Horizontal Termination-
Three elbows
0 ft.
0 mm
1-1/2 ft. 457 mm 2-1/2 ft.
762 mm
2 m
1 ft.
2 ft.
3 ft.
305 mm 3-1/2 ft.
762 mm 5-1/2 ft.
1.1 m
1.7 m
2.3 m
6-1/2 ft.
10-1/2 ft.
14 ft.
3.2 m
4.3 m
Note: Use DVP Series
components only.
1.1 m
7-1/2 ft.
H1 + H2 MAX. =14 FT (4.3 m)
V1 + V2 + H1 + H2 MAX. = 40 FT (12.2 m)
INSTALLED
HORIZONTALLY
Figure 5.14
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
19
3. Rear Vent - Horizontal Termination- (continued)
One elbow
V Minimum
1 ft. 305 mm 3-1/2 ft.
762 mm 5-1/2 ft.
1.1 m 7-1/2 ft.
H1 MAX. =7-1/2 FT (2.3 m)
V1 + H1 MAX. = 40 FT (12.2 m)
H1 Maximum
1.1 m
1.7 m
2.3 m
Note: Use DVP Series
components only.
2 ft.
3 ft.
V1
H1
Figure 5.15
V Minimum
H1 + H2 Maximum
3. Rear Vent - Horizontal Termination
Two elbows
1 ft.
2 ft.
3 ft.
305 mm 2-1/2 ft. 762 mm
762 mm 4-1/2 ft.
1.1 m 6-1/2 ft.
1.4 m
2 m
Note: Use DVP Series
components only.
H1 + H2 MAX. =6-1/2 FT (2.0 m)
V1 + H1 + H2 MAX. = 40 FT (12.2 m)
V1
INSTALLED
HORIZONTALLY
H1
H2
Figure 5.16
20
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Rear Vent - Horizontal Termination- (continued)
Three elbows
V Minimum
0 ft. 0 mm
H1 Maximum
H1 + H2 + H3 Maximum
1-1/2 ft. 457 mm 2-1/2 ft.
762 mm
2 m
1 ft.
2 ft.
3 ft.
305 mm 3-1/2 ft.
762 mm 5-1/2 ft.
1.1 m
1.7 m
2.3 m
6-1/2 ft.
10-1/2 ft.
14 ft.
3.2 m
4.3 m
Note: Use DVP Series
components only.
1.1 m
7-1/2 ft.
H1 MAX. =7-1/2 FT (2.3 m)
H1 + H2 MAX. =14 FT (4.3 m)
V1 + V2 + H1 + H2 MAX. = 40 FT (12.2 m)
V2
H2
V1
H1
Figure 5.17
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Vent Clearances and Framing
6
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
C
D
3 in. TOP
CLEARANCE
NOTE: Slope
not required.
A
1 in. CLEARANCE
AROUND VERTICAL
SECTIONS
*
B
*
1 in. SIDE AND
BOTTOM CLEARANCE
A
B
C
D
in. 36 1/2 24 3/8 35 1/2 23 3/8
mm 927 619 902 594
BE-36-C
Figure 6.1 Pipe Clearances
* Shows center of vent framing hole for top or rear venting.
The center of the hole is one (1) inch (25.4 mm) above the
center of the horizontal vent pipe.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102
mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than
7-1/4 in. (184 mm) a DVP-HSM-B will be required.
Figure 6.3 Exterior Wall Hole
Combustible Wall Penetration
Frame a hole in a combustible wall for an interior wall
shield firestop, (Figure 6.2) whenever a wall is penetrated.
Use same size framing materials as those used in the wall
construction. The wall shield firestop maintains minimum
clearances and prevents cold air infiltration.
HEAT
SHIELD
3 in. TOP
CLEARANCE
HEAT
SHIELD
7 in.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombus-
tible materials such as concrete, a hole with diameter one
inch greater than the pipe is acceptable.
1 in. CLEARANCE
BOTTOM & SIDES
WALL
SHIELD
FIRESTOP
WALL
Figure 6.2 Horizontal Venting Clearances to Combustible Materials
22
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Vertical Penetration Framing
WARNING
Fire Hazard
Keep loose materials or blown
insulation from touching the
vent pipe.
•
•
National building codes recommend us-
ing attic shield to keep loose materials/
blown insulation from contacting vent.
ATTIC ABOVE
Hearth & Home Technologies requires
the use of an attic shield.
10 IN. (254 MM)
Installing the Ceiling Firestop
• Frame an opening 10 inches by 10
inches whenever the vent system pene-
trates a ceiling/floor (see Figure 6.4).
• Frame the area with the same sized
lumber as used in ceiling/floor joist.
• When installing a top vent vertical ter-
mination appliance the hole should be
directly above the appliance, unless the
flue is offset.
10 IN.
(254 MM)
HOLE SHOULD MEASURE
10 IN. X 10 IN.
• Do not pack insulation around the vent.
Insulation must be kept away from the
pipe.
(254 MM X 254 MM)
INSIDE TO INSIDE
Installing Attic Shield
Note: An additional ceiling firestop is not
required if attic shield is used.
• Frame opening for attic shield.
Î
• Attic shield may be installed above or
below ceiling (see Figure 6.5).
Figure 6.4
• Secure with three fasteners on each
side.
BEND TABS IN
AROUND PIPE
• Fold tabs at top of attic shield in toward
vent pipe. Tabs must keep vent pipe
centered within shield.
3 FASTENERS
PER SIDE
• Field construct additional shield height if
insulation is deeper than height of attic
shield.
ATTIC SHIELD INSTALLED
ABOVE CEILING
ATTIC SHIELD INSTALLED
BELOW CEILING
Figure 6.5 Installing the Attic Shield
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Appliance Preparation
7
A. Choosing the Top or Rear Vent
Note: Actual unit may look different than the fireplace shown
in this section.
CAUTION
Sharp Edges
• Wear protective gloves and safety
glasses during installation.
Figure 7.4 Remove the seal cap.
Figure 7.1 For top vent, remove the two screws holding
the elbow heat shield in place. Use this heat shield over
the first elbow if applicable. For rear vent skip this step.
Figure 7.5 Remove the insulation basket and white insula-
tion from the center vent pipe.
Figure 7.2 Cut the seal cap strap across the rectangles
next to the disk. The top heat shield may need to be
removed to perform this step.
Figure 7.6 Remove the insulation from the outer vent
pipe. For rear venting there is no insulation in the outer
vent pipe. Replace the top heat shield.
Figure 7.3 Remove the white gasket material covering
the seal cap.
24
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7.7 To attach the first section of vent pipe, make
sure to use the fiberglass gasket in the manual bag to seal
between the first vent component and the outer fireplace
wrap. Use 2 self tapping screws to secure the gasket to
the outer wrap.
Figure 7.10 Fold the center parts of the retaining band out
and use to remove the vent cap.
Secure the first section of venting to the fireplace by
screwing through the two tabs bent up out of the vent
hole in the heat shield. Note: Once the vent cap has been
removed, it cannot be reattached.
B. Rear Vent
Figure 7.9 Discard the vent cap, remove and discard
the insulation basket. Note: Once the vent cap has been
removed it CANNOT be reattached.
Figure 7.8 Fold the tabs toward the center of the fire plug
(90°) and remove the insulation gasket.
Figure 7.10 Attach the first vent section (it will snap into
place). Slide the insulation gasket onto the vent section,
up against the appliance and over the tabs.
Figure 7.7 Cut the metal retaining band and fold the sides
out.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
25
C. Securing and Leveling the Appliance
WARNING
Fire Risk.
• Prevent contact with sagging, loose insulation.
• Do NOT install against combustible materials
such as exposed insulation, plastic and insulation
backer.
The diagram shows how to properly position, level, and
secure the appliance (see Figure 7.11). Nailing tabs are pro-
vided to secure the appliance to the framing members.
• Rear venting - refer to Vent Clearances and Framing
(Section 6B) for hole location.
• Place the appliance into position.
• Level the appliance from side to side and front to
back.
NAILING TABS
(BOTH SIDES)
• Shim the appliance, as necessary. It is acceptable to
use wood shims.
Figure 7.11 Proper Positioning, Leveling and
Securing of a Appliance
• Bend out nailing tabs on each side.
• Keep nailing tabs flush with the framing.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
WARNING
Fire Risk.
• ALWAYS maintain specified
NOTE: Once appliance is setup for top or rear venting,
it CANNOT be changed at a later time.
clearances around the appliance.
• Do NOT notch into the framing around the appliance spacers.
Failure to keep insulation, framing or other material away from
the appliance may cause fire.
26
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Vent Pipe
8
A. Assembly of Vent Sections (DVP Pipe ONLY)
WARNING
Fire Risk
Exhaust Fumes Risk
Impaired Performance of Appliance
• Overlap pipe slip sections at least 1-1/2 inches.
• Use pilot holes for screws.
• Screws must not exceed one inch long.
• Pipe may separate if not properly joined.
Figure 8.1 Lances
Attaching Vent to the Firebox Assembly
To attach the first pipe section to the collars, slide the male end of
the inner vent of the pipe section over the inner collar on the firebox
assembly.At the same time, slide the outer flue over the outer collar
on the appliance. Push the pipe section into the appliance collar until
all the lances (see Figure 8.1) have snapped in place. Tug slightly
on the section to confirm it has completely locked into place.
A
Assembling Pipe Sections
Insert the inner flue of section A into the flared inner flue of section B.
B
Start the outer flue of sectionAover the outer flue of section B (see
Figure 8.2). Note: The end of the pipe sections with the lances/tabs
on it will face towards the appliance.
Figure 8.2
Figure 8.3
Once both inner and outer flues
are started, press section A onto
section B firmly until all lances
have snapped into place. Check
to make sure they have snapped
together (see Figure 8.3) and
the seams are not aligned (see
Figure 8.4). Tug slightly on sec-
tion A to confirm it has completely
locked into place. It is acceptable
to use screws no longer than 1
inch to hold outer pipe sections
together. If predrilling holes, do
NOT penetrate inner pipe.
Note: Make sure that the seams are not aligned to prevent unintentional disconnection.
CORRECT
INCORRECT
Figure 8.4 Seams
For 90° and 45° elbows that are
changing the vent direction from
horizontal to vertical, one screw
minimum should be put in the
outer flue at the horizontal elbow
joint to prevent the elbow from ro-
tating. Use screws no longer than
1 inch. If predrilling screw holes,
do NOT penetrate inner pipe.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Assembling Minimum Installations (MI) Sections
Cut from this end
MI sections are non-unitized so that they can be cut to a
certain length. Cut these sections to length from the non-
expanded end (see Figure 8.5).
(outer)
They can then be attached by first connecting the expanded
end of the MI inner flue with the inner pipe from the adjacent
pipe section and securing with three screws. The expanded
portion of the MI inner flue must overlap completely with
the unexpanded end of the adjacent pipe section.
Cut from this end
(inner)
The outer flue can then be inserted into the adjacent outer
flue expanded end and attached to the next pipe section
with three screws. The other end of the MI pipe section can
then be attached by fitting another pipe section to it and
snapping it together, as normal.
Figure 8.5
Assembling DVP-12A Slip Sections
The outer flue of the slip section should slide over the outer
flue of the pipe section and into (inner flue) the last pipe
section (see Figure 8.6) .
Slide together to the desired length, making sure that a
1-1/2 inch outer flue overlap is maintained between the
pipe section and slip section.
The pipe and slip section need to be secured by driving
two screws through the overlapping portions of the outer
flues using the pilot holes (see Figure 8.7).
Pilot hole
This will secure the slip section to the desired length and
prevent it from separating. The slip section can then be
attached to the next pipe section.
Figure 8.6 Slip Section Pilot Holes
If the slip section is too long, the inner and outer flues of
the slip section can be cut to the desired length.
Figure 8.7 Screws into Slip Section
28
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing the Vent Sections
Vertical Sections
Vertical sections of pipe must be supported every 8 feet
after the 25 foot maximum unsupported rise. The vent sup-
port or plumber’s strap (spaced 120° apart) may be used
to do this (see Figure 8.8).
Horizontal Sections
Horizontal sections of vent must be supported every 5 feet
with a vent support or plumber’s strap.
Figure 8.8 Securing Vertical Pipe Sections
Figure 8.9 Securing Horizontal Pipe Sections
B. Disassembly of Vent Sections
(DVP Pipe ONLY)
To disassemble any two pieces of pipe, rotate either section
(see Figure 8.10), so that the seams on both pipe sections
are aligned (see Figure 8.11). They can then be carefully
pulled apart.
WARNING
Fire Risk.
Explosion Risk.
Combustion Fume Risk.
Use vent run supports per installation
instructions.
Figure 8.10 Rotate Seams for Disassembly
Connect vent sections per installation
instructions.
• Maintain all clearances to combustibles.
• Do NOT allow vent to sag below
connection point to appliance.
Improper support may allow vent to sag or separate.
Figure 8.11 Align and Disassemble Vent Sections
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Assembly of Vent Sections (SL Series Pipe ONLY)
WARNING
Fire Risk
Exhaust Fumes Risk
Impaired Performance of Appliance
• Ensure vent components are locked together correctly.
• Pipe may separate if not properly joined.
Figure 8.12 Adding Venting Components
Attach the First Vent Component to Starting Collars
To attach the first vent component to the starting collars
of the appliance:
Install Support Brackets
For Horizontal Runs - The vent system must be supported
every five (5) feet of horizontal run by a horizontal pipe
support.
• Lock the vent components into place by sliding the
concentric pipe sections with four (4) equally spaced in-
terior beads into the appliance collar or previously installed
component end with four (4) equally spaced indented sec-
tions.
To install support brackets for horizontal runs:
• Place the pipe supports around the vent pipe.
• Nail the pipe supports to the framing members.
• When the internal beads of each outer pipe line up, ro-
tate the pipe section clockwise about one-quarter (1/4)
turn (see Figure 8.13). The vent pipe is now locked
together.
For Vertical Runs - The vent system must be supported
every eight (8) feet (2.4m) above the appliance flue outlet by
wall brackets. To install support brackets for vertical runs:
• Attach wall brackets to the vent pipe and secure the wall
bracket to the framing members with nails or screws.
• Slide the ceramic fiber pad over the first vent section
and place it flush to the appliance. This will prevent cold
air infiltration. High temp caulk may be used to hold the
part in place. Continue to add vent components.
WARNING
Fire Risk.
Explosion Risk.
Combustion Fume Risk.
Continue Adding Vent Components
• Continue adding vent components, locking each suc-
ceeding component into place.
Use vent run supports per installation
instructions.
• Ensure that each succeeding vent component is securely
Connect vent sections per installation
instructions.
fitted and locked into the preceding component.
•
•
Maintain all clearances to combustibles.
Do NOT allow vent to sag below
connection point to appliance.
• 90° elbows may be installed and rotated to any point
around the preceding component’s vertical axis. If an
elbow does not end up in a locked position with the
preceding component, attach with a minimum of two (2)
sheet metal screws.
•
Maintain specified slope (if required).
Improper support may allow vent to sag or separate.
30
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Installing Heat Shield and Horizontal Termination Cap (DVP Pipe ONLY)
Installing the Horizontal Termination Cap
WARNING
Vent termination must not be recessed in the wall. Siding
Fire Hazard
may be brought to the edge of the cap base.
Impaired performance of appliance
Flash and seal as appropriate for siding material at outside
edges of cap.
• Telescoping flue section of termination cap
MUST be used when connecting pipe section
to termination cap.
When installing a horizontal termination cap, follow the cap
location guidelines as prescribed by current ANSI Z223.1
and CAN/CGA-B149 installation codes.
• Maintain a 1-1/2 inch minimum overlap on
telescoping flue section of termination cap.
WARNING
WARNING
Burn Risk
Fire Risk
• Local codes may require installation of a cap
shield to prevent anything or anyone from
touching the hot cap.
Exhaust Fumes Risk
Impaired Performance of Appliance
• Overlap pipe slip sections at least 1-1/2 inches.
• Use pilot holes for screws.
• Screws must not exceed 1 inch long.
• Pipe may separate if not properly joined.
Heat Shield Requirements for Horizontal Termination
For all horizontally vented appliances, a heat shield MUST
be placed one inch above the top of the vent between the
wall shield firestop and the base of the termination cap.
There are two sections of the heat shield. One section
attaches to the wall shield firestop with two screws. The
remaining section is attached to the cap in the same
manner.
If the wall thickness does not allow the required 1-1/2
inch heat shield overlap, an extended heat shield must
be used.
Figure 8.12 Venting through the Wall
The extended heat shield will need to be cut to the thick-
ness of the wall and be attached to the wall shield firestop.
The small leg on the extended heat shield should rest on
the top of the vent (pipe section) to properly space it from
the pipe section (see Figure 8.12).
NOTE: Where required, an exterior wall flashing is available.
When penetrating a brick wall, a brick extension kit is available
for framing the brick.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Installing Wall Shield Firestops and Horizontal Termination Cap (SL Series Pipe ONLY)
WARNING
WARNING
Fire Risk
Exhaust Fumes Risk
Impaired Performance of Appliance
Fire Risk.
Explosion Risk.
Do NOT pack insulation or other
combustibles between firestops.
• Ensure vent components are locked together correctly.
• Pipe may separate if not properly joined.
•
•
ALWAYS maintain specified clearances around venting
and firestop systems.
Install firestops as specified.
ForHorizontalRuns-WallshieldfirestopsareREQUIREDon
bothsidesofacombustiblewallthroughwhichtheventpasses.
Failure to keep insulation or other material away from
vent pipe may cause fire.
NOTE: Model SLK-01TRD does not need an exterior
wall shield firestop on an exterior combustible wall.
To install wall shield firestops for horizontal runs that pass
through either interior or exterior walls:
Installing the Horizontal Termination Cap
Cut a 10 in. x 10 in. (254mm x 254mm) hole for SL-D-
series pipe. The center of the framing hole is one (1) inch
(25.4mm) above the center of the horizontal vent pipe.
Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
Flash and seal as appropriate for siding material at out
side edges of cap.
• Position the wall shield firestops on both sides of the
hole previously cut and secure the wall shield firestops
with nails or screws.
When installing a horizontal termination cap, follow the cap
location guidelines as prescribed by current ANSI Z223.1
and CAN/CGA-B149 installation codes.
• The heat shields of the wall shield firestops MUST BE
placed towards the top of the hole.
• Continue the vent run through the wall shield firestops.
WARNING
10 in.
(254mm)
Burn Risk
• Local codes may require installation of a
cap shield to prevent anything or anyone
from touching the hot cap.
1 in. (25.4 mm)
10 in.
(254mm)
WARNING
Do NOT connect a pipe section to a termination cap without using
VENT PIPE
the telescoping flue section found on the termination cap.
Figure 8.14 Hole and Vent Pipe
NOTE: Where required, an exterior wall flashing is available.
When penetrating a brick wall, a brick extension kit is avail-
able for framing the brick.
HEAT SHIELD
TRIM HEAT
SHIELD IF TOO
LONG, ADD TO
SHIELD IF TOO
SHORT
WALL SHIELD
FIRESTOP
(EXTERIOR)
WALLSHIELD
FIRESTOP
(INTERIOR)
Figure 8.15 Heat Shield, Interior & Exterior Firestops
32
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Î
Caulk the gap between the roof flashing and the outside
diameter of the pipe. Also caulk the perimeter of flashing
that contacts roof surface as shown in Figure 8.18.
D. Installing Roof Flashing and
Vertical Termination Cap
To install roof flashing see Figure 8.16.
To attach the vertical termination cap, slide the inner col-
lar of the cap into the inner flue of the pipe section and
place the outer collar of the cap over the outer flue of the
pipe section.
For installation of vertical termination cap see minimum vent
heights for various pitched roofs (see Figure 8.16) .
HORIZONTAL
OVERHANG
Secure with three screws into the outer flue. Secure the cap
by driving the three self-tapping screws (supplied) through
the pilot holes in the outer collar of the cap into the outer
flue of the pipe (see Figure 8.17).
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
WALL
LOWEST
DISCHARGE
OPENING
TERMINATION CAP
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
(1 of 3)
STORM
COLLAR
Roof Pitch
H (Min.) Ft.
Flat to 6/12.......................................1.0*
Over 6/12 to 7/12...........................1.25*
Over 7/12 to 8/12.............................1.5*
Over 8/12 to 9/12.............................2.0*
Over 9/12 to 10/12............................ 2.5
Over 10/12 to 11/12........................ 3.25
Over 11/12 to 12/12.......................... 4.0
Over 12/12 to 14/12.......................... 5.0
Over 14/12 to 16/12.......................... 6.0
Over 16/12 to 18/12.......................... 7.0
Over 18/12 to 20/12.......................... 7.5
Over 20/12 to 21/12.......................... 8.0
SCREWS
CAULK
Figure 8.17
* 3 foot minimum in snow regions
Figure 8.16 Minimum Height from Roof to
Lowest Discharge Opening
Î
CAULK
WARNING
Fire Risk.
Explosion Risk.
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may
ignite.
• Restricted air flow affects burner operation.
Î
Figure 8.18
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Assembling and Installing Storm Collar
CAUTION
Sharp Edges
• Wear protective gloves and safety
glasses during installation.
Connect both halves of the storm collar with two screws
(see Figure 8.19).
Wrap the storm collar around the exposed pipe section
and align brackets. Insert a bolt (provided) through the
brackets and tighten nut to complete storm collar assembly
(see Figure 8.20).
Figure 8.20 Assembling the Storm Collar Around the Pipe
Slide the assembled storm collar down the pipe section
until it rests on the roof flashing.
Caulk around the top of the storm collar (see Figure
8.17).
Figure 8.19 Assembling the Storm Collar
34
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Information
9
A. Fuel Conversions
C. Gas Connection
Before making gas connections ensure that appliance be-
ing installed is compatible with the available gas type.
NOTE: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualified installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.)
Any natural or propane gas conversions necessary to
meet the appliance and locality needs must be made by
a qualified technician using Hearth & Home Technologies
specified and approved parts.
B. Gas Pressures
Proper input pressures are required for optimum appli-
ance performance. Gas line sizing requirements need to
be made following NFPA51.
NOTE: A listed (and Commonwealth of Massachusetts
approved) 1/2 inch (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 inch (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
WARNING
Fire Risk.
Refer to Reference Section 16 for location of gas line
access in appliance.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
NOTE: Gas line may be run from either side of the appliance
provided the hole in the outer wrap does NOT exceed 2-1/2
inches in diameter and does not penetrate the firebox.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
WARNING
Gas Leak Risk
• Support control when attaching pipe to prevent
bending gas line.
WARNING
Verify inlet pressures.
• High pressure may cause overfire condition.
• Low pressure may cause explosion.
NOTE: The gap between supply piping and gas access
hole may be caulked with high temperature caulk or stuffed
with non-combustible, unfaced insulation to prevent cold air
infiltration.
• Verify minimum pressures when other
household gas appliances are operating.
Install regulator upstream of valve if line pressure
is greater than 1/2 psig.
Pressure requirements for appliance are shown in the
table below. Minimum pressures must be met when other
household gas appliances are operating.
Pressure
Natural Gas
Propane
Minimum
Inlet Pressure
5.0 inches
w.c.
11.0 inches
w.c.
Maximum Inlet
Gas Pressure
14.0 inches
w.c.
14.0 inches
w.c.
Manifold
Pressure
3.5 inches
w.c.
10.0 inches
w.c.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
35
• Ensure that gas line does not come in contact with outer
wrap of appliance. Follow local codes.
HIGH ALTITUDE INSTALLATIONS
U.L. Listed gas appliances are tested and approved
without requiring changes for elevations from 0 to
2000 feet in the U.S.A. and Canada.
• Incoming gas line should be piped into the valve com-
partment and connected to the 1/2 inch connection on
the manual shutoff valve.
When installing this appliance at an elevation above
2000 feet, it may be necessary to decrease the
input rating by changing the existing burner orifice
to a smaller size. Input rate should be reduced by
4% for each 1000 feet above a 2000 foot elevation
in the U.S.A., or 10% for elevations between 2000
and 4500 feet in Canada. If the heating value of the
gas has been reduced, these rules do not apply. To
identify the proper orifice size, check with the local
gas utility.
WARNING
Fire or Explosion Hazard
• Gas buildup during line purge may ignite.
• Purge should be performed by qualified technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as
sparks or open flames.
If installing this appliance at an elevation above 4500
feet (in Canada), check with local authorities.
•
A small amount of air will be in the gas supply lines.
When first lighting appliance it will take a short time for
air to purge from lines. When purging is complete the
appliance will light and operate normally.
WARNING
CHECK FOR GAS LEAKS
Explosion Risk
Fire Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially-available,
non-corrosive leak check solution. Be sure
to rinse off all leak check solution following
testing.
Fittings and connections may have
loosened during shipping and handling.
WARNING
Fire hazard.
Do NOT change the valve settings.
• This valve has been preset at the factory.
• Changing valve settings may result in fire
hazard or bodily injury.
36
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Information
10
A. Recommendation for Wire
B. Connecting to the Appliance
This appliance requires 110-120 VAC be wired to the
junction box either for use of optional accessories (stand-
ing pilot ignition) or for proper operation of the appliance
(Intellifire ignition). Refer to Figure 10.1 to determine if the
appliance uses an Intellifire ignition system or Standing
Pilot ignition system.
WARNING
Wire 110V to electrical junction box.
Do NOT wire 110V to valve.
Do NOT wire 110V to wall switch.
• Incorrect wiring will damage millivolt valves.
• Incorrect wiring will override IPI safety lockout
and may cause explosion.
Open the control access panel to view wiring system and
gas valve. If this appliance has a red or black ignitor button
(as noted in Figure 10.1) this appliance has a Standing Pilot
ignition system. If there is no red or black ignitor button,
this appliance has an Intellifire ignition system.
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
• If using thermostat use one compatible with a millivolt
gas valve system.
• Follow parameters for locating thermostat (see individual
thermostat instructions) to ensure proper operation of
appliance.
• Use low resistance thermostat wire for wiring from igni-
tion system to the wall switch and thermostat.
• Keep wire lengths short as possible by removing any
excess wire length.
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
Figure 10.1 Standing Pilot Ignition
NOTE: This appliance must be electrically wired and grounded
in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest
edition or the Canadian Electric Code, CSA C221.1.
PILOT
THERMOPILE
THERMOCOUPLE
PIEZO
THERMOSTAT
WIRE ASSEMBLY
RED
VALVE
Figure 10.2 Standing Pilot Ignition Wiring Diagram
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
37
C. Standing Pilot Ignition System Wiring
D. Intellifire Ignition System Wiring
This appliance requires a 110 VAC supply to the appliance
junction box for operation. A wiring diagram is shown in
Figure 10.3.
• This standing pilot ignition system wiring does not require
a 110 VAC supply to operate.
• It is recommended that a 110 VAC junction box be in-
stalled for use with a fan or remote control. (See Figure
10.4 for junction box wiring).
This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
This appliance is supplied with a battery pack and a 3 voltAC
transformer, which requires the installation of the supplied
junction box. It is highly recommended that the junction box
be installed at this time to avoid reconstruction.
SENSOR
BLOWER
SWITCH
The battery pack requires two D cell batteries (not
included).
Batteries cannot be placed in the battery pack while
using the 3 volt AC transformer. The transformer must
be unplugged if the battery pack is used or battery life
will be reduced.
FAN
RECEPTACLE
SPEED
CONTROL
CAUTION
Figure 10.1 Blower wiring
Battery polarity must be correct or module damage will occur.
WARNING
CAUTION
Shock hazard.
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
• Replace damaged wire with type 105º C
rated wire.
• Wire must have high temperature insulation.
IGNITION MODULE 3 VAC
INTERMITTENT PILOT IGNITOR
I
S
TRANSFORMER
3 VAC
WHITE
ORANGE
GROUND TO
FIREPLACE
CHASSIS
PLUG IN
JUMPER WIRE
(TO BROWN)
BATTERY PACK
THERMOSTAT
WIRE ASSEMBLY
VALVE
Figure 10.3 Intellifire Ignition Wiring Diagram
38
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Junction Box Installation
Romex
Connector
If the box is being wired from the appliance:
•
Remove the screw attaching the junction
box to the outer shell, rotate the junction box
inward to disengage it from the outer shell
(see Figure 10.4).
14/2WG
Cover Plate
outside firebox
•
•
Pull the electrical wires from outside the
appliance through this opening into the valve
compartment.
Loosen the two screws on the Romex
connector (not included with unit), feed the
necessary length of wire through the connector
and tighten the screws.
Copper
ground attached
to GRN screw with
GRN wire
•
Make all necessary wire connections to the
receptacle and assemble the receptacle and
cover to the junction box.
GRN wire
inside box
NOTE: Do NOT wire
110VAC to wall switch.
Figure 10.4 Junction Box Detail
F. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted
switch for use with a fan (See Figure 10.5):
•
The power supply for the appliance must
be brought into a switch box.
SWITCH
MINIMUM 14-3 AWG
WITH GROUND
•
The power can then be supplied from
the switch box to the appliance using a
minimum of 14-3 with ground wire.
Red
Black
White
Green
Black
White
Green
JUNCTION BOX
•
•
•
At the switch box connect the black (hot)
wire and red (switch leg) wire to the wall
switch as shown.
POWER
SUPPLY WIRES
At the appliance connect the black (hot),
white (neutral) and green (ground) wires
to the junction box as shown.
SWITCH BOX
Add a 1/4 inch insulated female connector
to the red (switch leg) wire, route it through
the knockout in the face of the junction
box, and connect to the top fan switch
connector (1/4 inch male) as shown.
Red
Figure 10.5 Junction Box Wired to Wall Switch
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Finishing
11
A. Mantel Projections
FINISH WALL MATERIAL MAY BE
COMBUSTIBLE - TOP AND SIDES
Figure 11.1 shows the minimum vertical and corresponding
maximum horizontal dimensions of appliance mantels or
other combustible projections above the top front edge of
the appliance.
0 IN.
1-1/4 IN.
0 IN.
0 IN.
HIGH TEMPERATURE (3000F / 1490 C MIN.)
TOP & SIDE SEAL JOINT
1
”
”
2
Figure 11.3 Noncombustible Facing
WARNING
Figure 11.1 Clearances to Mantels or other Combustibles
above Appliance
Risk of Fire
• Non-combustible clearances MUST be
maintained.
• Sheetrock, wood or other combustibles must
NOT be used as sheathing or facing in the
non-combustible zone.
• See Section 11 for proper clearances.
• See Section 1 for combustible/non-combustible
definitions.
Note: Clearance
from opening to
perpendicular wall.
NOTE: There are 3 metal tabs holding the non-combustible
board in place for shipping. These tabs are to be cut off or
bent back before finishing around the appliance front.
Figure 11.2 Mantel Leg or Wall Projections
(Acceptable on both sides of opening.)
WARNING
B. Facing Material
Fire Risk.
Finish all edges and fronts to clearances and
WARNING
specifications listed in manual.
•
•
•
•
Black metal appliance front may be covered with
noncombustible material only.
Fire Risk.
Do NOT obstruct air inlet or outlet grilles.
Do NOT modify grilles.
Do NOT overlap combustible materials onto appliance
front.
•
Modifying or covering grilles could cause
temperature rise and fire hazard.
Finishing materials must not interfere with:
Install combustible materials only up to specified
clearances on top, front and side.
•
•
•
Air flow through grilles or louvers.
Operation of louvers or doors.
Access for service.
Seal joints between the finished wall and appliance top
and sides using only a 300º F minimum sealant.
40
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance Setup
12
A. Remove Shipping Materials
Remove shipping materials from inside or underneath the
WARNING
firebox.
Explosion Risk.
• Follow ember placement instructions in
manual.
• Do NOT place embers directly over
burner ports.
• Replace ember material annually.
B. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
Improperly placed embers interferes with proper burner
operation.
C. Accessories
Placing the Ember Material
Install approved accessories per instructions included with
accessories. See Service Parts List for appropriate acces-
sories. Refer to Section 16.
Ember material is shipped with this gas appliance. To place
the ember material:• Embers CANNOT be placed di-
rectly over ports. Care should be taken not to cover the
lighting trail of ports (from back to front).
• When placing Glowing Embers® onto the burner care
should be taken so that the ports are not covered. Place
the dime-size ember pieces near the port holes in the
burner top (see Figure 12.1). Failure to follow this pro-
cedure will likely cause lighting and sooting problems.
WARNING
Shock or fire risk.
Use ONLY optional accessories approved for
this appliance.
• Using non-listed accessories voids warranty.
• Using non-listed accessories may result in a
safety hazard.
• Only Hearth & Home Technologies approved
accessories may be used safely.
EMBER MATERIALS
Figure 12.1 Placement of Embers
• Place lava rock on base pan on both sides of the burner.
Do NOT place on burner top.
• Save the remaining ember materials for use during appli-
ance servicing. The embers provided should be enough
for 3 to 5 applications.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
41
D. Positioning the Logs
Log Set Assembly: LOGS-BE-36-C
Models: BE-36-C
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the following instructions.
1
TAB
TAB
2
3
Carefully remove the logs from the packaging. CAUTION: Logs are fragile!
1
2
LOG # 2 (SRV397-702): Place log #2 on the left
side of the grate in front of log #1. The left edge of log #2
should touch the firebox. The right edge of log #2 should
be pushed back until it touches the tab. NOTE: It may be
necessary to tilt log #1 back slightly while placing log #2 on
the grate.
LOG #1 (SRV397-701): Place log #1 so the notch
on the right side rests on the right grate tine. The left side
of log #1 should rest on the pilot bracket. Slide the log to
the rear until it touches the rear tab.
LOG # 3 (SRV397-703): Place log #3 on the right
side of the grate in front of log #1. The right edge of log #3
should touch the firebox while the rear lines up with the left
log. The left edge of log #3 should rest on the grate and log
#1 as shown.
3
397-935B 6/04
42
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Glass Assembly
F. Grilles and Trim
Install optional marble and brass trim surround kits as
desired. Marble, brass, brick, tile, or other non-combustible
materials can be used to cover up the gap between the
sheet rock and the appliance.
WARNING
Handle glass doors with care.
• Inspect the gasket to ensure it is
undamaged.
Do not obstruct or modify the air inlet/outlet grilles or hood.
When overlapping on both sides, leave enough space so
that the bottom grille can be lowered and the trim door
removed.
• Inspect the glass for cracks, chips or
scratches.
• Any scratch in glass, requires replacement.
• Do NOT strike, slam or scratch glass.
Shutter Settings
• Do NOT operate appliance with glass door removed,
cracked, broken or scratched.
Models
NG
LP
• Replace glass door assembly as a complete appliance.
BE-36-C
1/4 in.
3/8 in.
Removing Glass Assembly
Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 12.2).
Replacing Glass Assembly
Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
LATCHES
(BOTH BOTTOM
AND TOP)
GLASS
ASSEMBLY
Figure 12.2 Glass Assembly
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Operating Instructions
13
A. Before Lighting Appliance
WARNING
Before lighting this appliance determine if it has a Standing
Pilot or Intellifire ignition system by opening the control
access panel to view wiring system and gas valve. If this
appliance has a red or black ignitor button (see Figure
10.1) this appliance has a Standing Pilot ignition system.
If there is no red or black ignitor button, this appliance has
an Intellifire ignition system.
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT
Glass and other surfaces are hot during operation and
cool down.
•
•
Keep children away.
CAREFULLY SUPERVISE children in same room
as appliance.
CAUTION
•
•
•
Alert children and adults to hazards of high
temperatures.
If installing Intellifire ignition battery backup:
• Do not install batteries if the backup mode may not be
used for extended time.
• Batteries may leak.
• Install batteries only when needed for power outage.
Do NOT operate with protective barriers open or
removed.
Keep clothing, furniture, draperies and other
combustibles away.
This appliance has been supplied with an integral barrier to
prevent direct contact with the fixed glass panel. Do NOT
operate the appliance with the protective barrier removed.
Before operating this appliance have a qualified tech-
nician:
•
Remove all shipping materials from inside and/or
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
underneath the firebox.
•
Review proper placement of logs, rockwool, lava
rock, and vermiculite.
•
•
•
•
Check the wiring.
WARNING
Check the air shutter adjustment.
Ensure that there are no gas leaks.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
the owner’s information manual provided with this appliance.
For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
Ensure that the glass is sealed and in the proper
position.
•
Ensure that the flow of combustion and ventilation air
is not obstructed (front grilles and vent caps).
WARNING
WARNING
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Glass door must be in place when appliance
is operating.
Risk of:
• Combustion Fumes
• Fire
Do NOT operate appliance with glass door
removed.
• Open viewing glass for servicing only.
• Glass door MUST be in place and sealed before operating
appliance.
• Only use glass door certified for use with appliance.
• Glass replacement should be done by qualified technician.
44
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Lighting Appliance
FOR YOUR SAFETY
LIGHTING
INSTRUCTIONS
(IPI)
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
1. Turn off all electric power to the appliance.
2. This appliance is equipped with an ignition
device which automatically lights the burner.
Do not try to light the burner by hand.
•
•
Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) de-
vice which automatically lights the
burner. Do not try to light the burner
by hand.
If you cannot reach your gas sup-
plier, call the fire department.
GAS
VALVE
B. BEFORE LIGHTING, smell all
around the appliance area for gas.
Be sure to smell next to the floor
because some gas is heavier than
air and will settle on the floor.
C. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been
under water.
3. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor.
If you smell gas, STOP! Follow “B” in the
Safety Information located on the left side of
this label. If you don’t smell gas, go to next
step.
WHAT TO DO IF YOU SMELL GAS
•
•
Do not try to light any appliance.
Do not touch any electric switch; do
not use any phone in your building.
4. Turn on all electric power to the appliance.
WARNING: CAUTION:
5. To light the burner, flip the ON/OFF switch to
the “ON” position. (The ON/OFF switch may
include a wall switch if so equipped).
Hot while in operation. Do not touch.
Keep children, clothing, furniture, gaso-
line and other liquids having flammable
vapors away.
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
6. If the appliance will not operate, follow the
instructions “To Turn Off Gas to Appliance”
and call your service technician or gas sup-
plier.
Improper installation, adjustment, al-
teration, service or maintenance can
cause injury or property damage. Refer
to the owner’s information manual pro-
vided with this appliance.
Do not operate the appliance with
panel(s) removed, cracked or broken.
Replacement of the panel(s) should be
done by a licensed or qualified service
person.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
TO TURN OFF
GAS TO APPLIANCE
NOT FOR USE
WITH SOLID FUEL
If not installed, operated, and main-
tained in accordance with the manufac-
turer’s instructions, this product could
expose you to substances in fuel or
fuel combustion which are known to the
State of California to cause cancer, birth
defects, or other reproductive harm.
1. Turn off all electric power to the appliance if
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
service is to be performed.
2. Flip ON/OFF switch to the “OFF” position.
Also Certified for Installation in a
593-913D
Bedroom or a Bedsitting Room.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
For assistance or additional informa-
tion, consult a qualified installer, ser-
vice agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Standing Pilot Ignition
LIGHTING
INSTRUCTIONS
FOR YOUR SAFETY
READ BEFORE LIGHTING
1. Turn off all electric power to the appliance.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
2. Push in gas control knob
slightly and turn clockwise
to “OFF”.
A. This appliance has a pilot which
•
If you cannot reach your gas sup-
plier, call the fire department.
NOTE: Knob cannot be turned from “PILOT” to “OFF”
unless knob is pushed in slightly. Do not force.
must be lighted by hand. When light-
ing the pilot, follow these instructions
exactly.
C. Use only your hand to push in or
turn the gas control knob. Never use
tools. If the knob will not push in or
turn by hand, don’t try to repair it, call
a qualified service technician. Force
or attempted repair may result in a
fire or explosion.
3. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the Safety Information
located on the left side of this label. If you don’t
smell gas, go to next step.
B. BEFORE LIGHTING, smell all
around the appliance area for gas.
Be sure to smell next to the floor
because some gas is heavier than
air and will settle on the floor.
4. Find the pilot. The pilot is inside
combustion chamber next to the
main burner.
WHAT TO DO IF YOU SMELL GAS
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been
under water.
•
•
Do not try to light any appliance.
Do not touch any electric switch; do
not use any phone in your building.
5. Turn knob on gas control counter clockwise
•
Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
to “PILOT”.
6. Push in control knob all the way and hold in. Im-
mediately depress red or black piezo button. It may
require several depressions of the red or black
piezo button until PILOT lights. If PILOT light does
not light after 10 seconds, return to step 3. Continue to
hold the control knob in for about one minute after the
pilot is lit. Release knob and it will pop back out. Pilot
should remain lit. If it goes out, repeat steps 3 through 6.
WARNING:
DO NOT CONNECT 110 VAC TO
CAUTION:
Hot while in operation. Do not touch.
Keep children, clothing, furniture, gaso-
line and other liquids having flammable
vapors away.
THE CONTROL VALVE.
•
•
If knob does not pop up when released, stop and im-
mediately call your service technician or gas supplier.
Improper installation, adjustment, al-
teration, service or maintenance can
cause injury or property damage. Refer
to the owner’s information manual pro-
vided with this appliance.
If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your service
technician or gas supplier.
Do not operate the appliance with
panel(s) removed, cracked or broken.
Replacement of the panel(s) should be
done by a licensed or qualified service
person.
7. Turn gas control knob counterclockwise to
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
“ON”.
8. To light Burner, flip the on/off switch to the “ON” posi-
tion, and close access grille.
NOT FOR USE
WITH SOLID FUEL
If not installed, operated, and main-
tained in accordance with the manufac-
turer’s instructions, this product could
expose you to substances in fuel or
fuel combustion which are known to the
State of California to cause cancer, birth
defects, or other reproductive harm.
9. Turn on all electric power to the appliance.
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
TO TURN OFF
GAS TO APPLIANCE
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
1. Turn off all electric power to the appliance if service
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
is to be performed.
For assistance or additional informa-
tion, consult a qualified installer, service
agency or the gas supplier.
2. Open control access panel.
3. Move switch to “OFF” position.
4. Push in gas control knob slightly and turn clock-
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
wise
to OFF”. Do not force.
5. Close control access panel.
464-903G
46
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
C. After Appliance is Lit
Initial Break-in Procedure
When you light the appliance, you may notice that it pro-
duces heat which does have an associated odor or smell.
If you feel this odor is excessive it may require the initial
three to four hour continuous burn on high followed by a
second burn up to 12 hours to fully drive off any odor from
paint and lubricants used in the manufacturing process.
Condensation of the glass is normal.
CAUTION
• Prevent accidental appliance operation when not
attended.
• Unplug or remove batteries from remote control if absent
or if appliance will not be used for an extended period of
time.
• Property damage possible from elevated temperatures.
NOTE: The appliance should be run three to four hours
on the initial start-up. Turn it off and let it cool completely.
Remove and clean the glass. Replace the glass and run
the appliance for an additional 12 hours. This will help to
cure the products used in the paint and logs.
CAUTION
Smoke and odors released during initial operation.
•
•
•
Open windows for air circulation.
Leave room during initial operation.
Smoke may set off smoke detectors.
During this break-in period it is recommended that some
windows in the house be opened for air circulation. This will
help avoid setting off smoke detectors, and help eliminate
any odors associated with the appliance’s initial burning.
Smoke and odors may be irritating to sensitive
individuals.
WARNING
WARNING
Fire Risk.
Fire Hazard.
High Temperatures.
Keep combustible materials, gasoline and
other flammable vapors and liquids clear of
appliance.
Keep combustible household items away from
appliance.
Do NOT obstruct combustion and ventilation air.
• Do NOT store flammable materials in the
appliance’s vicinity.
• Do NOT place combustible items on top of or
in front of appliance.
• Do NOT use gasoline, lantern fuel, kerosene,
charcoal lighter fluid or similar liquids in this
appliance.
• Keep furniture, draperies away from
appliance.
• Combustible materials may ignite.
D. Frequently Asked Questions
ISSUE
SOLUTIONS
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Condensation of the glass
This is a result of normal operation and the flames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.
Blue flames
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufactur-
ing. Odor may also be released from finishing materials and adhesives used around the
appliance.
Odor from appliance
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Metallic noise
Is it normal to see the pilot flame burn
In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when
ON/OFF is turned off. In a standing pilot system the pilot will always stay on.
continually?
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Troubleshooting
14
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.
A. Standing Pilot Ignition System
Symptom
Possible Causes
Corrective Action
1. After repeated triggering a. Defective ignitor.
of the red or black piezo
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor.
ignitor button, the spark
ignitor will not light the pilot.
b. Defective pilot or misaligned
electrode (spark at electrode).
Using match, light the pilot. If the pilot lights, turn off the pilot and
trigger the red piezo ignitor button again. If the pilot lights, an im-
proper gas/air mixture caused the bad lighting and a longer purge
period is recommended. If the pilot will not light, ensure the the gap
at the electrode and pilot is one-eighth (1/8) inch to have a strong
spark. If the gap is OK, replace the pilot.
c. No gas or low gas pressure.
Check the remote shut-off valves from the fireplace. Usually, there
is a valve near the gas main. There can be more than one (1) valve
between the fireplace and the main.
d. No LP in tank.
Check the LP (propane) tank. You may be out of fuel.
2. The pilot will not stay lit
after carefully following the
lighting instructions.
a. Defective thermocouple.
Check that the pilot flame impinges on the thermocouple. Clean
and/or adjust the pilot for maximum flame impingement.
Ensure that the thermocouple connection at the gas valve is fully
inserted and tight (hand tighten plus 1/4 turn).
Disconnect the thermocouple from the valve, place one millivolt
meter lead wire on the tip of the thermcouple and the other meter
lead wire on the thermocouple copper lead. Start the pilot and hold
the valve knob in. If the millivolt reading is less than 15mV, replace
the thermocouple.
b. Defective valve.
If the thermocouple is producing more than 15 millivolts, replace
faulty valve.
3. The pilot is burning,
a. ON/OFF switch or wires
defective.
Check the ON/OFF switch and wires for proper connections. Place
the jumper wires across the terminals at the switch. If the burner
comes on, replace the defective switch. If the switch is OK, place the
jumper wires across the switch wires at the gas valve. If the burner
comes on, the wires are faulty or connections are bad.
there is no burner flame ,
the valve knob is in the ON
position, and the ON/OFF
switch is in the ON position.
b. Thermopile may not be gener- If the pilot flame is not close enough physically to the thermopile,
ating sufficient millivoltage.
adjust the pilot flame.
Be sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millvolt meter. Take the reading at
TH-TP&TP terminals of the gas valve. The meter should read 325
millivolts minimum, while holding the valve knob depressed in the
pilot position, with the pilot lit, and the ON/OFF switch in the OFF
position. Replace the faulty thermopile if the reading is below the
specified minimum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The read-
ing should be 325 millivolts minimum. Replace the thermopile if the
reading is below the minimum.
48
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (continued)
Symptom
Possible Cause
Corrective Action
3. Continued
c. Defective valve.
Turn the valve knob to the ON position. Place the
ON/OFF switch in the ON position. Check the millivolt
meter a the thermopile terminals. The millivolt meter
should read greater than 125mV. If the reading is ac-
ceptable, and if the burner does not come on, replace
the gas valve.
d. Plugged burner orifice.
e. Wall switch or wires are defective.
Check the burner orifice for stoppage. Remove stop-
page.
Follow the corrective action in Symptom and Pos-
sible Cause 1.a above. Check the switch and wiring.
Replace where defective.
4. Frequent pilot outage a. Pilot flame may be too high or too low, or blow-
Clean thermocouple and adjust the pilot flame for
problem.
ing out (high pressure), causing pilot safety to drop maximum flame impingement. Follow lighting instruc-
out.
tions carefully.
5. The pilot and main
burner extinguish while
in operation.
a. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
b. Inner vent pipe leaking exhaust gases back into Check venting system for damage. Replace/repair
the system.
improperly assembled pipe sections.
c. Glass too loose and air tight packet leaks in
corners after usage.
Replace glass panel assembly.
d. Bad thermopile or thermocouple.
e. Improper vent cap installation.
Replace if necessary.
Check for proper installation and freedom from debris
or blockage.
6. Glass soots.
a. Flame impingement.
Adjust the log set so that the flame does not exces-
sively impinge on it.
b. Improper air shutter setting.
c. Debris around air shutter.
Adjust the air shutter located on the control panel.
Inspect the opening at the base of the burner. NO MA-
TERIAL SHOULD BE PLACED IN THIS OPENING.
7. Flame burns blue
and lifts off burner.
a. Insufficient oxygen being supplied.
Ensure that the vent cap is installed properly and free
of debris. Ensure that the vent system joints are tight
and have no leaks.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
49
B. Intellifire Ignition System
Sympton
Possible Cause
Corrective Action
1. The ignitor/module
makes noise, but no
spark.
a. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor
are connected to correct terminals on module and pilot assembly.
Reversed wires at the module may cause system to make sparking
noise, but spark may not be present at pilot hood.
b. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from mod-
ule to pilot assembly. Rod closest to pilot hood should be ignitor.
Verify connections underneath pilot assembly are tight; also verify
connections are not grounding out to metal chassis, pilot burner,
pilot enclosure, mesh screen if present, or any other metal object.
c. Ignitor gap is too large.
d. Faulty module.
Verify gap of igniter to pilot hood. The gap should be approximately
.17 inch or 1/8 inch.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
2. Pilot won’t light,
there is no noise or
spark.
a. Transformer installed correctly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
b. A shorted or loose connection in wir- Remove and reinstall the wiring harness that plugs into module.
ing configuration or wiring harness.
Verify there is a tight fit. Verify pilot assembly wiring to module.
Remove and verify continuity of each wire in wiring harness.
c. Improper wall switch wiring.
d. Module not grounded.
Verify that 110/VAC power is “ON” to junction box.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
3. Pilot lights but con-
tinues to spark, and
main burner will not ig-
nite. (If the pilot contin-
ues to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
a. A shorted or loose connection in
sensor rod.
Verify all connections to wiring diagram in manual. Verify connec-
tions underneath pilot assembly are tight. Verify connections are
not grounding out to metal chassis, pilot burner, pilot enclosure or
screen if present, or any other metal object.
b. Poor flame rectification or contami- Verify that flame is engulfing sensor rod. If the pilot assembly does
nated sensor rod.
not have a ground strap, consider installing one to increase flame
rectification. Verify correct pilot orifice is installed and inlet gas
specifications. Flame carries rectification current, not the gas. If
flame lifts from pilot hood, the circuit is broken. A wrong orifice or
too high an inlet pressure can cause pilot flame to lift. The sensor
rod may be contaminated. Clean sensor rod with emery cloth.
50
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Intellifire Ignition System - (continued)
Symptom
Possible Cause
Corrective Action
3. (Continued) Pilot lights c. Module is not grounded.
but continues to spark,
and main burner will not
Verify that module is securely grounded to metal chassis
of appliance. Verify that wire harness is firmly connected to
module.
ignite. (If the pilot contin-
ues to spark after the pilot d. Damaged pilot assembly or dirty sensor Verify that ceramic insulator around the sensor rod is not
flame has been lit, flame
rectification has not oc-
curred.)
rod.
cracked, damaged, or loose. Verify connection from sen-
sor rod to white sensor wire. Clean sensor rod with emery
cloth to remove any contaminants that may have accumu-
lated on sensor rod. Verify continuity with a multimeter with
ohms set at lowest range.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF posi-
tion. Remove ignitor wire “I” from module. Place ON/OFF
Rocker switch or wall switch in ON position. Hold ground
wire about 3/16 inch away from “I” terminal on module. If
there is no spark at “I” terminal module must be replaced.
If there is a spark at “I” terminal, module is fine. Inspect
pilot assembly for shorted sparker wire or cracked insulator
around electrode.
4. Pilot sparks, but Pilot
will not light.
a. Correct gas supply.
Verify that incoming gas line ball valve is “open”. Verify that
inlet pressure reading is within acceptable limits, inlet pres-
sure must not exceed 14 in. W.C.
b. Ignitor gap is too large.
c. Module is not grounded.
Verify that spark gap from ignitor to pilot hood is .17 in. or
1/8 in.
Verify module is securely grounded to metal chassis of
appliance.
d. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batter-
ies if voltage is below 2.7.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Maintaining and Servicing Appliance
15
Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified
service technician should perform an appliance check-up at the beginning of each heating season.
CAUTION
WARNING
Handle glass assembly with care.
Risk of injury or property damage.
Before servicing:
NOTE: Clean glass after initial 3-4 hours operation.
Longer operation without cleaning glass may
cause a permanent white film on glass.
• Turn off gas.
• Turn off electricity to appliance.
• Disable remote control, if one is present.
• Ensure appliance is completely cooled.
After servicing:
When cleaning glass door:
• Avoid striking, scratching or slamming glass.
• Do NOT use abrasive cleaners.
• Replace any screen or barrier that was removed.
• Reseal and reinstall any venting removed for servicing.
• Use a hard water deposit glass cleaner on white film.
• Do NOT clean glass when hot.
• Turn off appliance after 3-4 hours of operation and
ALLOW TO COOL.
WARNING
• Remove and clean glass assembly.
Annual inspection by qualified technician recommended.
• Replace glass assembly and operate appliance for
additional 12 hours.
Check:
• Condition of doors, surrounds and fronts.
• Condition of glass, glass assembly and glass seal.
• Obstructions of combustion and ventilation air.
• Condition of logs.
Refer to maintenance instructions.
• Condition of firebox.
• Burner ignition and operation.
• Burner air shutter adjustment
• Gas connections and fittings.
• Obstructions of termination cap.
WARNING
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
Clean:
• Glass
• Air passageways, grilles,
control compartment
• Burner, burner ports
• Combustible materials blocking cap may ignite.
• Restricted air flow affects burner operation.
Risk of:
• Fire
• Delayed ignition or explosion
• Exposure to combustion fumes
• Odors
52
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspect
Maintenance Tasks
Doors, Surrounds
and Fronts
1. Assess condition of screen and replace as necessary.
Recommend addition of screen if one is not present.
2. Inspect for scratches, dents or other damage and repair as necessary.
3. Verify no obstructions to airflow through the louvers.
4. Verify maintenance of proper clearance to combustible household objects.
1. Inspect gasket seal and its condition.
Gasket Seal, Glass
Assembly and Glass
2. Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.
3. Confirm there is no damage to glass or glass frame. Replace as necessary.
4. Verify that latches engage properly, clip studs are not stripped, and glass attachment components are intact
and operating properly. Replace as necessary.
5. Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.
Valve Compartment
and Firebox Top
1. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw
tips that have penetrated the sheet metal are sharp and should be avoided.
2. Remove any foreign objects.
3. Verify unobstructed air circulation.
Logs
1. Inspect for broken, damaged, or missing logs. Replace as necessary.
2. Verify correct log placement and no flame impingement causing sooting. Correct as necessary.
1. Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.
2. Replace appliance if firebox has been perforated.
Firebox
Burner Ignition and
Operation
1. Verify burner is properly secured and aligned with pilot or igniter.
2. Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.
3. Replace ember materials with new dime-size and shape pieces. Do not block ports or obstruct lighting paths.
4. Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.
5. Inspect for lifting or other flame problems.
6. Verify air shutter is clear of dust and debris.
7. Inspect orifice for soot, dirt or corrosion.
8. Verify manifold and inlet pressures. Adjust regulator as required.
9. Inspect pilot flame strength. Clean or replace orifice as necessary.
10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with emery
cloth or replace as required.
11. Verify millivolt output. Replace as necessary.
Venting
1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.
2. Confirm that termination cap remains clear and unobstructed by plants, etc.
3. Verify that termination cap clearance to subsequent construction (building additions, decks, fences or
sheds) has been maintained.
4. Inspect for corrosion or separation.
5. Verify weather stripping, sealing and flashing remains intact.
6. Inspect draft shield to verify it is not bent, damaged or missing.
1. Verify operation of remote.
Remote controls
2. Replace batteries in remote transmitters and battery-powered receivers.
3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure
or leaking.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Reference Materials
16
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
P
O
Q
R
N
M
Ø
S
L
Ø
GAS LINE
ACCESS
D
K
T
F
C
J
X
E
G
I
U
B
ELECTRICAL
ACCESS
V
W
A
H
Location
Inches
36
Millimeters
913
Location
Inches
8-3/4
16-1/4
1/2
Millimeters
222
413
13
A
B
C
D
E
F
G
H
I
M
N
O
P
31
790
32-1/2
27-3/8
18-1/2
31
826
695
25-3/4
12-7/8
15-7/8
6-5/8
30
654
327
403
168
762
54
470
Q
R
S
787
3-1/2
6-7/8
23-3/8
32-1/2
36-1/2
8
89
174
T
594
U
V
2-3/8
6
J
826
152
25
K
L
927
W
X
1
203
30-1/8
765
Figure 16.1 Appliance Dimensions
54
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams
Effective Length
Pipe
DVP4
Inches
Millimeters
10-1/2 in.
(267 mm)
4
102
°
45
Effective
Height/Length
DVP6
6
12
152
305
DVP12
DVP24
DVP36
DVP48
DVP6A
24
610
4-7/8 in.
( 276 mm)
36
914
48
1219
76 to 152
10-7/8 in.
(276 mm)
3 to 6
DVP Pipe (see chart)
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
°
DVP45 (45 Elbow)
11-3/8 in.
(289 mm)
10 in.
(254 mm)
10 in.
1 in.
(254 mm)
(25 mm)
7-3/8 in.
(187 mm)
24 in.
(610 mm)
1-1/4 in. (32 mm)
9-1/4 in.
(235 mm)
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
DVP-FS (Ceiling Firestop)
DVP-AS (Attic Shield)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1 in.
(25 mm)
8 in.
(203 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
14 in.
(356 mm)
UP
5 in.
(127 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.2 DVP vent components
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
55
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Minimum
Effective Length
Maximum
Effective Length
Term Cap
4-1/8 in.
105 mm
6-3/4 in.
171 mm
5-5/8 in.
143 mm
10-5/8 in.
270 mm
Max
Effective
Length
Trap1
12 in.
(305 mm)
DVP-TRAP
Horizontal Termination Cap
Trap2
DVP-TRAP1
DVP-TRAPK1
DVP-TRAP2
DVP-TRAPK2
DVP-HPC1
DVP-HPCK1-B
DVP-HPC2
DVP-HPCK2-B
Figure 16.3 DVP vent components
56
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(367 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(127 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(367 mm)
RF6M
RF12M
Roof Flashing Multi-pak
Roof Flashing Multi-pak
5 in.
(127 mm)
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-3/4 in.
(349 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
COOL-ADD
Cap Shield
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DVP-TRAPFL
Flashing
DRC-RADIUS
Cap Shield
Figure 16.4 DVP vent components
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
57
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
3-7/8 in.
(98 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
10-1/2 in.
(267 mm)
DVP-TV
Vertical Termination Cap
12 in.
(305 mm)
DVP-TB1
Basement Vent Cap
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
(High wind)
Vertical Termination Cap
PVK-80
(For use with IPI and DSI appliances only.)
7-1/4 in.
(184 mm)
14 in.
(356 mm)
16-7/8 in.
(429 mm)
1 in.
(25 mm)
12 in.
(305 mm)
14 in.
(356 mm)
7-1/8 in.
12-1/8 in.
(181 mm)
(314 mm)
3/8 in. (10 mm)
1 in. (25 mm)
8-3/4 in.
(222 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
1-5/8 in.
(41 mm)
DVP-FBHT
Fire Brick Termination Cap
DVP-HPC
High Performance Cap
Figure 16.5 DVP vent components
58
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
6-1/2 in.
Pipe
Length/Inches
SL-06D
SL-09D
5-3/4
8-3/4
SL-12D
11-3/4
SL-12/17D
SL-17/24D
SL-24D
SL-36D
SL-48D
SL-FLEX-2
SL-FLEX-3
SL-FLEX-5
SL-FLEX-10
11-3/4 to 16-3/4
16-3/4 to 23-3/4
23-3/4
35-3/4
47-3/4
24
36
60
120
There must be a 25% reduction
in total H when using the snorkel
cap except when using the
simple up and out installation.
WALL BRACKET
(SL- SERIES)
Figure 16.6 SL Series Vent Components
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Î
BE-36-C
C. Service Parts
Beginning Manufacturing Date: 4-01
Ending Manufacturing Date: ______
Service Parts Diagram
9
5
6
4
7
11
12
10
Log Set Assembly
8
1
3
2
Part number list on following page.
60
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Î
C. Service Parts List
BE-36-C
AVAILABLE
TO SHIP IN 24
HOURS
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers’
VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
ITEM
DESCRIPTION
SERIAL #
PART NUMBER
LOGS-BE36-C
SRV397-701
SRV397-702
SRV397-703
550-382A
394-176A
397-018
Log Assembly
Log 1
Y
1
2
3
4
Log 2
Log 3
Mesh Assembly
Y
Y
Pre 0021076020
Post 0021076020
5
Burner Assembly
6
7
Glass Door Assembly
Louver, Top
GLA-550TR
397-249
8
Louver, Bottom
Grate Assembly
Hood
397-248
9
397-361A
SRV550-175
397-120
10
11
Grate Support
Burner Orifice NG (#45C)
Burner Orifice LP (#55C)
Lava Rock
582-845
Y
Y
582-855
060-721
Mineral Wool
050-721
Exhaust Restrictor
Glass Latch Assembly
Touch Up Paint
530-299
386-122A
TUP-GBK-12
Y
Y
Standing Pilot
100-250A
N/A
12
Junction Box
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Conversion Kit NG
NGKS-BE36-C
LPK-BE36-C
LPKS-BE36-C
060-517
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Conversion Kit LP
Regulator NG
Regulator LP
NGK-11
060-516
LPK-11
446-505
Pilot Spud NG
Pilot Spud LP
2103-116
446-517
2103-117
IPI System
383-250A
Pre April 2004
Post April 2004
12
Junction Box
4021-013
NGK-BE36-CIPI
LPK-BE36-CIPI
NGK-DXF
LPK-DXF
Conversion Kit NG
Conversion Kit LP
Regulator NG
Y
Y
Y
Y
Y
Y
Regulator LP
446-505
Pilot Spud NG
Pilot Spud LP
446-517
Additional service part numbers may appear on the following page.
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Î
Service Parts
BE-36-C
Beginning Manufacturing Date: 4-01
Ending Manufacturing Date: ______
Valve Assembly List
Standing Pilot Valve Assembly
4
3
6
5
8
7
1
2
IMPORTANT: THIS IS DATED INFORMATION. The most current information is lo-
cated on your dealers’ VIP site. When ordering, supply serial and model numbers to
ensure correct service parts.
AVAILABLE
TO SHIP IN 24
HOURS
ITEM
DESCRIPTION
SERIAL #
PART NUMBER
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
060-520
Y
Y
Y
Y
Y
1
Valve NG
Valve LP
418-500
060-521
1
418-501
2045-024
2045-407
485-510A
2103-010
530-511A
2103-011
2025-101
2025-101/2044-155
530-431
2
3
Thermostat Wire Assembly
Burner Neck Gasket
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Y
Y
Y
Y
4
4
5
Pilot Assembly NG
Pilot Assembly LP
Valve Bracket
6
7
8
Valve Plate Gasket
Flexible Gas Connector
Piezo Ignitor
530-302A
291-513
Y
Y
Y
530-302A
530-164
Flex Tube Assembly
Pre 0021076020
Post 0021076020
Pilot Bracket
N/A
62
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Î
Service Parts
Valve Assembly Parts List
BE-36-CIPI
Beginning Manufacturing Date: 4-01
Ending Manufacturing Date: ______
IPI Valve Assembly
4
3
6
5
14
12
9
7
11
13
2
10
IMPORTANT: THIS IS DATED INFORMATION. The most current information is
located on your dealers’ VIP site. When ordering, supply serial and model numbers
to ensure correct service parts.
AVAILABLE
TO SHIP IN 24
HOURS
ITEM
DESCRIPTION
SERIAL #
PART NUMBER
593-500
593-501
2045-024
2045-407
385-510A
2090-012
385-511A
2090-013
2025-101
530-431
530-302A
2012-206
593-592
593-590A
593-594A
593-593A
530-302A
385-512
N/A
Valve NG
Valve LP
Y
Y
Y
1
2
3
Thermostat Wire Assembly
Burner Neck Gasket
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
4
4
Pilot Assembly NG
Pilot Assembly LP
5
6
Valve Bracket
Valve Plate Gasket
Flexible Gas Connector
Jumper Wires
7
Y
Y
Y
Y
Y
Y
Y
9
10
11
12
13
14
Module
Wire Assembly
Battery Pack
3 Volt Transformer
Flex Tube Assembly
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Pre 0021076020
Post 0021076020
Ground Strap
530-164
N/A
Pilot Bracket
397-121
N/A
Pilot Assembly Support
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
63
D. Limited Lifetime Warranty
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies
BASIC ONE-YEAR WARRANTY. HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, war-
rants to the original owner that your new HEARTH & HOME TECHNOLOGIES Gas Appliance (the “Product”) will be free from defects in materials
and workmanship for a period of one year from the date of installation. During the first year, HEARTH & HOME TECHNOLOGIES will replace
or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs incurred in
replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.
EXTENDED LIFETIME COVERAGE. HEARTH & HOME TECHNOLOGIES INC warrants that the firebox, heat exchanger, log(s), and burner
will not be defective in material or workmanship during the period the Product is owned by the original owner, subject to the following conditions,
exclusions and limitations described below.
CONDITIONS, EXCLUSIONS AND LIMITATIONS:
1. This warranty applies to the original owner only and is nontransferable.
2. This warranty applies only to Products installed in the United States of America or Canada.
3. This warranty is limited to the replacement or repair of defective components or workmanship and HEARTH & HOME TECHNOLOGIES
may fully discharge all obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum
amount recoverable under this warranty is limited to the purchase price of the Product and, if HEARTH & HOME TECHNOLOGIES is un-
able to provide replacement or repair in an expedient and cost-effective manner, HEARTH & HOME TECHNOLOGIES may discharge all
obligations under this warranty by refunding the purchase price of the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE PRODUCT.
4. Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited
Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-Year Warranty.
5. Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty
unless expressly authorized and approved by HEARTH & HOME TECHNOLOGIES in writing.
6. Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure,
air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.
7. This warranty will be void if:
a) The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s
Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.
b) Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved
by HEARTH & HOME TECHNOLOGIES INC in writing.
c) Any service work is performed on the Product by anyone other than an authorized HEARTH & HOME TECHNOLOGIES representa-
tive.
d) The Product is damaged due to shipping, improper handling, accident, abuse or misuse.
e) Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.
f ) Modification was made to the Product which was not expressly authorized and approved by HEARTH & HOME TECHNOLOGIES in writing.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HEARTH & HOME TECHNOLOGIES INC MAKES NO EXPRESS WARRANTIES OTHER
THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE
WARRANTY SPECIFIED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential
damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from State to State.
If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or compo-
nents, contact the nearest authorized HEARTH & HOME TECHNOLOGIES dealer or supplier.
NOTES TO CUSTOMER:
1. In order to insure proper installation, operation and maintenance HEARTH & HOME TECHNOLOGIES INC strongly recom-
mends annual servicing by an authorized HEARTH & HOME TECHNOLOGIE dealer.
2. Please complete this information and retain this warranty in a safe place for future reference: Installation Date:______
Model #:_________________ Serial #:______________ Installing Contractor:_________________________
3. HEARTH & HOME TECHNOLOGIES INC reserves the right to make changes at any time, without notice, in design, mate-
rial, specifications and prices of the Product. HEARTH & HOME TECHNOLOGIES also reserves the right to discontinue
styles and products.
© 2005 Hearth & Home Technologies Inc.
64
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Contact Information
Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
www.fireside.com
Please contact your Hearth & Home Technologies
dealer with any questions or concerns.
For the location of your nearest Hearth & Home Technologies
dealer, please visit www.fireside.com.
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843,
5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237,
5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860,
6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039,
6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Printed in U.S.A. - Copyright 2006
Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07
Download from Www.Somanuals.com. All Manuals Search And Download.
65
|
Grizzly Saw G0524 User Manual
Hach Scanner DR 5000 User Manual
Haier Turntable MWG7047TW B User Manual
Hasbro Games 56220 55603 User Manual
Hasselblad Camera Lens FE 28 50 User Manual
HP Hewlett Packard Personal Computer 600B MT PC User Manual
HP Hewlett Packard Photo Printer A820 series User Manual
IBM Computer Monitor 9516 BXX User Manual
Icom Pet Fence AP 12 User Manual
Image Treadmill IMTL99600 User Manual