INSTRUCTION MANUAL
BEFORE INSTALLATION
1
2
3
4
5
6
7
WIRELESS ACCESS POINT
OBTAINING AN IP ADDRESS
FROM THE DHCP SERVER
AP-12
FIXED IP ADDRESS SETTING
AP-12 MANAGER
SETTING EXAMPLES
IP CONFIGURATION
REFERENCES
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
IMPORTANT
When connecting the AP-12 to a bridging type modem (or in
bridging mode) directly, a global IP address may be assigned to
the AP-12 from the modem, according to the modem settings.
When a global IP address is assigned to the AP-12, an illegal
operator, such as a cracker, a hacker, may access it.
To avoid such access, connect a router between the modem
and the AP-12.
The bridge type modem assigns a global IP address to the connect-
ed PC (only one).
The router type modem assigns a private IP address (e.g.192.168.x.x)
to the connected PCs via the HUB by the built-in routing function. The
AP-12 can be connected to a router type modem directly.
Contact your Internet Service Provider (ISP) if you do not know your
modem type.
About exchanging the AP-12 or the PC connected to the AP-12.
The AP-12 memorizes the communication settings between the AP-
12 and the connected PC. Thus, if the AP-12 and/or the PC con-
nected to it changed, communication may fail.
In such case, turn the AP-12 power OFF. After waiting a few sec-
onds, turn the power ON again.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
FOREWORD
Thank you for purchasing the Icom Wireless Access
point AP-12.
This wireless access point is provided with the func-
tions necessary for supporting a wireless LAN.
This manual is designed to help you use the product to
its fullest potential. Read this manual carefully before
using the product.
TRADEMARK CREDITS
Icom, Icom Inc. and the
logo are registered trade-
marks of Icom Incorporated (Japan) in the United
states, the United Kingdom, Germany, France, Spain,
Russia and/or other countries.
Windows is a registered trademark of Microsoft
Corporation in the United States and/or other coun-
tries.
The screen shots that appear in this manual are used
with permission of Microsoft Corporation.
Other product and company names mentioned herein
are trademarks or registered trademarks of their
respective owners.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
FEATURES
" Up to 11 Mbps data transmission rate with automatic fallback function (11/5.5/2/1
Mbps).
" The supplied utility software, [AP-12 Manager] allows you simple setup of the sys-
tem with a step-by-step tutorial. Windows XP, Windows Me, Windows 98SE,
Windows 98, Windows 2000 are supported.
" The diversity antenna is built into the compact body to provide stable communi-
cation.
" Versatile operating modes for Access Point mode, Bridge mode A (Peer-to-Peer),
Bridge mode B (Client mode), and Bridge mode C (Multi-site). A roaming function
is also available while in Access Point mode. It provides full mobility and seam-
less network access from anywhere within the area for the connected clients.
" The DHCP client function is available to automatically obtain the network config-
uration such as the IP address (This is not activated in Bridge mode B mode oper-
ation).
" Data can be protected with high-level security function such as 128/64-bit WEP
(Wired Equivalent Privacy) encryption and MAC address registration.
" AP-12 uses a direct spread-spectrum communication system which ensures sta-
bilized communication even under influence of noise and interference.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
FCC INFORMATION
AP-12
Tested to comply
with FCC standards
FOR HOME OR OFFICE USE
CAUTION: Changes or modifications not expressly approved by Icom Inc. could
void the user’s authority to operate this Access Point.
Class B digital device users;
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE SAFETY INFORMATION:
CAUTION: To comply with the FCC RF exposure requirements, this transmitter (built-
in antenna) must be fixed-mounted on permanent structures with a separation distance
of at least 8 inches (20cm) from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
For CANADA only
Operation is subject to the following two conditions: (1) this device may not cause inter-
ference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
GENERAL PRECAUTIONS
" If a connection cable is disconnected or has a loose connection during operation,
an error may occur. Connect the connectors correctly, and do not touch the con-
nectors during operation.
" For the operation of PC and peripheral devices, follow the instructions provided in
the manuals which come with the PC and peripheral devices.
" This device may cause signal interference when used in a domestic setting. When
interference occurs, move this unit as far as possible away from the affected
device.
" The CD which comes with the AP-12 is for the AP-12 only.
Do not use it for any other devices.
" Icom Inc. is not responsible for any interference that arises by incorporating a con-
figuration file for the AP-12 or a firmware update data file, which is available on
our home page, into any device other than the AP-12. Moreover, Icom Inc. is not
responsible for any interference that arises by modifying or disassembling the AP-
12. Furthermore, Icom Inc. is not responsible for any damages, lost profits or third
party’s claim resulting from any missed communication or telephone call due to
the AP-12’s fault, error, malfunction, breakage, data loss or any other external
factor such as power failure.
" All copyrights associated with this manual and all intellectual property rights asso-
ciated with the hardware and software of the AP-12 are held by Icom Inc.
" Unauthorised reproduction or transmission of this manual, or any part hereof, is
prohibited.
" The content of this manual, the hardware and software associated with the AP-
12, and the appearance of the AP-12 are all subject to change without notice.
Notational Conventions
The following notational conventions are used in this manual:
• The names of utilities, menus, windows, tabs, icons, text boxes, and check boxes
are enclosed in square brackets ([ ]).
• The names of command buttons within dialog boxes are enclosed in less-than and
greater-than signs (< >).
- Windows 98 SE represents the Windows 98 Second Edition.
Windows Me represents the Windows Millennium Edition.
- The contents of windows appearing in this manual may vary depending on the op-
erating system installed on your PC.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
I Supplied accessories
AP-12
Patch cable
3 m (9.8 feet)
Crossover cable
1 m (3.2 feet)
AP-12 Main Unit
CD
Leg Pad
Fixing Sheet
AC Adapter
Instruction Manual
Registration Card
Warranty Card
• Leg Pad …………………… Attach to the bottom of the AP-12 to secure.
• Fixing sheets ……………… Attach to the bottom of the AP-12 to secure.
Remove the protective paper before attaching the
sheet.
• Crossover cable…………… For connection between the AP-12 and a PC.
• Patch cable………………… For network connection between the AP-12 and
HUB.
• CD ………………………… [AP-12 Manager] is included.
• AC Adapter………………… The adapter for the AP-12.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
IMPORTANT ………………………………………………………………………………ii
INTRODUCTION …………………………………………………………………………iii
ACCESSORIES …………………………………………………………………………vii
TABLE OF CONTENTS ………………………………………………………………viii
SAFETY PRECAUTIONS ………………………………………………………………x
Chapter 1
BEFORE INSTALLATION ………………………………1–8
1-1 Wireless functional modes ……………………………………2
1-2 Unit description …………………………………………………4
1-3 Accessory attachment …………………………………………5
1-4 Installation location………………………………………………7
1-5 About the Ethernet card…………………………………………8
Chapter 2
Chapter 3
OBTAINING AN IP ADDRESS
FROM THE DHCP SERVER……………………………9–14
2-1 Connecting to a LAN …………………………………………10
2-2 Installing [AP-12 Manager] ……………………………………11
2-3 Starting [AP-12 Manager] ……………………………………13
FIXED IP ADDRESS SETTING ………………………15–29
3-1 Connecting to the PC …………………………………………16
3-2 Using [Easy Setting Wizard] …………………………………17
3-3 Installing [AP-12 Manager] ……………………………………25
3-4 Starting [AP-12 Manager] ……………………………………27
Chapter 4
Chapter 5
AP-12 MANAGER ……………………………………31–44
4-1 [AP-12 Manager] screen descriptions ………………………32
4-2 The default settings ……………………………………………43
4-3 Uninstalling [AP-12 Manager]…………………………………44
SETTING EXAMPLES…………………………………45–49
5-1 Access point mode ……………………………………………46
5-2 Bridge mode A (Peer-to-Peer) ………………………………47
5-3 Bridge mode B (Client Mode)…………………………………48
5-4 Bridge mode C (Multi-site) ……………………………………49
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Chapter 6
IP CONFIGURATION …………………………………51–56
6-1 For Windows XP ………………………………………………52
6-3 For Windows 98/98SE/Me ……………………………………54
6-2 For Windows 2000 ……………………………………………55
Chapter 7
REFERENCES …………………………………………57–71
7-1 Troubleshooting ………………………………………………58
7-2 Connecting the AP-12 and HUB ……………………………60
7-3 Verifying the connection to the AP-12 ………………………60
7-4 Failure in searching for the AP-12……………………………61
7-5 IP address confirmation ………………………………………64
7-6 Connection to the router type modem ………………………66
7-7 Specifications …………………………………………………68
7-8 Glossary …………………………………………………………70
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
Be sure to read these precautions in order to use the AP-12 safely.
• These precautions are intended to ensure that the access point is operated
safely and correctly. Follow these instructions to avoid property damage
and prevent personal injury to yourself (user) or others in the vicinity.
• Before reading the rest of this manual, read and understand the precautions
listed under “RWARNING” and “RCAUTION”.
• After reading this manual, store it in a convenient place for future review.
I Wireless Access Point
Failure to observe the precautions listed here
could result in serious or fatal injury to the user or
those near the user.
RWARNING
G Do not use any AC adapter other than
the one provided with this product.
Otherwise fire, electric shock, or equip-
ment failure may result.
G Use the specified parts and acces-
sories only.
G This unit does not require adjustment.
Do not disassemble or modify the unit
or attempt to repair it yourself.
Otherwise fire, electric shock, or equip-
ment failure may result.
G Do not install in a location where the
unit can easily become wet (such as
adjacent to a humidifier).
Otherwise fire, electric shock, or equip-
ment failure may result.
G Do not connect the power supply to
any terminal other than the DC jack.
Otherwise fire, electric shock, or equip-
ment failure may result.
G Do not modify, excessively bend,
twist, pull, or heat the connecting
cables.
Otherwise the cables may be damaged
and cause a fire, electric shock, or equip-
ment failure.
G Do not place heavy objects on the
connecting cables or allow the cables
to be pinched.
Otherwise fire, electric shock, or equip-
ment failure may result.
G Do not handle the unit with wet hands.
Otherwise electric shock may result.
G Discontinue use immediately and
unplug the power cable from the AC
receptacle if the unit emits smoke, an
abnormal odor, or an abnormal noise
or if water enters the unit.
Otherwise fire, electric shock, or equip-
ment failure may result.
Disconnect the plug of the AC adapter
and all other cables from the unit.
Confirm that the smoke, odor, or noise
has stopped and contact your dealer.
Otherwise the cables may be damaged
and cause a fire, electric shock, or equip-
ment failure.
G Install and use in a location where
children cannot reach the power
cable and cables.
Pulled cables could result in electric
shock or personal injury.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
Failure to observe the precautions listed here could
result in personal injury or property damage.
RCAUTION
G Do not install the unit outdoors.
Otherwise equipment failure may result.
G Do not place on a slanted or unstable
surface.
Otherwise the unit may tilt over or fall,
resulting in personal injury or equipment
failure.
G Do not stand, sit, or place heavy
objects on the unit. Do not pinch the
unit.
Otherwise the unit may be damaged.
G When thunder and/or lightning occur
nearby, disconnect the AC adapter
from the wall socket and do not use
the unit. Also, discontinue such work
as connecting cables, disconnecting
cables, installation, or maintenance.
Otherwise fire or electric shock may
result.
G Do not use in locations where con-
densation is likely to occur. Avoid
hastily moving the unit to a location
where the humidity level is very dif-
ferent because condensation may
occur.
G Avoid installing in humid, dusty, or
poorly ventilated locations.
Otherwise equipment failure may result.
G Do not use in locations exposed to
direct sunlight, close to heating or
cooling ducts, or otherareas subject
to severe fluctuations in temperature.
Otherwise the unit may become
deformed or discolored. Also, fire or
equipment failure may result.
G Be sure to connect the cables cor-
rectly as explained in this manual. Do
not use any other connection
arrangement.
Otherwise the unit may become
deformed or discolored. Also, fire or
equipment failure may result.
Otherwise equipment failure may result.
G Avoid locations exposed to strong
magnetic fields or static electricity
and locations exposed to tempera-
tures or humidity levels that exceed
the specifications listed in the manu-
al.
If condensation occurs, dry the unit or
allow the unit to remain in the same envi-
ronment until it is completely dry before
using it again.
G Disconnect the AC adapter from the
unit when the unit will not be used for
a long time.
Otherwise equipment failure may result.
G Do not use close to radios or televi-
sion sets.
Otherwise signal interference may occur.
G Do not drop or the unit or subject it to
strong physical shock.
Otherwise the unit may become hot and
fire or equipment failure may result.
G Do not clean with paint thinner or ben-
zene.
Otherwise the case material may
degrade or the coating may peel. Clean
with a soft cloth. When particularly dirty,
dampen the cloth slightly with a neutral
cleaning agent that has been diluted with
water.
Otherwise personal injury or equipment
failure may result.
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
IAC adapter
Failure to observe the precautions listed here could
result in serious or fatal injury to the user or those
near the user.
RWARNING
G Do not use with an AC supply voltage
other than 230 V.
Otherwise fire, electric shock, or equip-
ment failure may result.
G Do not use with any device other than
the AP-12.
Otherwise fire, electric shock, or equip-
ment failure may result.
G Do not modify, excessively bend,
twist, pull, or heat the AC power cable.
Otherwise the cable may be damaged
and cause a fire, electric shock, or equip-
ment failure.
G Do not place heavy objects on top of
the DC output cable or allow the cable
to be pinched.
G Hold the adapter body when plugging
in and unplugging the AC adapter. Do
not yank the cable.
Otherwise fire, electric shock, or equip-
ment failure may result.
G Do not handle the AC adapter plug or
other devices with wet hands.
Otherwise electric shock may result.
G Do not use the AC adapter if the DC
output cable is damaged or the plug
does not fit securely into the recepta-
cle.
Otherwise fire, electric shock, equipment
failure, or data loss may result.
Consult with your dealer or the service
staff at one of our sales offices regarding
how to handle the problem or obtain a
new AC adapter.
Otherwise the cable may be damaged
and cause a fire, electric shock, or equip-
ment failure.
General Precautions
GThe unit may malfunction if the connecting cables become disconnected or the connection
is unstable while the unit is in operation. Be sure all connectors are securely fastened and
do not touch them while the unit is in operation.
GObserve the instructions provided in the manuals included with the PC and other periph-
eral devices.
GThis device may cause signal interference when used in a domestic setting. When inter-
ference occurs, move this unit as far as possible away from the affected device.
GThe disks entitled “Utility Software” (utility for updating the firmware) is specifically intend-
ed for this unit. Do not use the disks with any other device.
GICOM Inc. assumes no responsibility whatsoever for any trouble resulting from using the
data files originally provided with this unit or the firmware update data files provided on our
website in a device other than this unit, or modifying or disassembling this unit. Nor does
ICOM Inc. assume any responsibility whatsoever for any damages or lost profits resulting
from opportunities for voice or signal communications being lost because of the failure,
malfunction, poor condition, damage, or data loss of this unit or because of such external
causes as power failure. ICOM also dismisses all responsibility for demands made by a
third party.
GAll copyrights associated with this manual and all intellectual property rights associated
with the hardware and software of this product are held by ICOM Inc.
GUnauthorised reproduction or transmission of this manual, or any part hereof, is prohibited.
GThe content of this manual, the hardware and software associated with this product, and
the appearance of this product are all subject to change without notice.
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
Chapter
1
This chapter describes what you should consider and prepare before installing the AP-12.
1-1 Wireless functional modes…………………………………………………………2
I Access point mode …………………………………………………………………2
I Bridge mode A (Peer-to-Peer) ……………………………………………………2
I Bridge mode B (Client Mode) ……………………………………………………3
I Bridge mode C (Multi-site)…………………………………………………………3
I About a MAC address ……………………………………………………………3
1-2 Unit description………………………………………………………………………4
1-3 Accessory attachment………………………………………………………………5
I Leg pads/fixing sheet attachment…………………………………………………5
I To avoid falling………………………………………………………………………5
I To avoid interference ………………………………………………………………6
1-4 Installation location …………………………………………………………………7
I Examples of recommended installation …………………………………………7
I Examples of installation not recommended ……………………………………7
I Installation precautions ……………………………………………………………7
1-5 About the Ethernet card ……………………………………………………………8
I Desktop PC …………………………………………………………………………8
I Notebook PC ………………………………………………………………………8
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
1
1-1 Wireless functional modes
The AP-12 has 4 wireless functional modes.
A functional mode can be selected with [AP-12 Manager].
• The AP-12 obtains an IP address from the DHCP server automatically (default).
• Bridge mode B does not support a DHCP client function.
• Connect the AP-12 to the PC directly (p. 16), then set the IP address when you use
the fixed IP address in the existing wired LAN.
I Access point mode (default)
The AP-12 in access point mode con-
nects the wireless LAN clients to the
other wireless LAN clients or wired
Ethernet LAN
AP-12 [CH 11]
Wireless LAN
LAN.
client
To avoid communication speed slow
Wireless LAN
down, it is recommended to use up to
client
10 AP-12’s only during heavy traffic.
CH:Channel
[CH 6]
By connecting two or more AP-12’s to
the wired LAN, roaming is possible.
The roaming function switches to the
most suitable access point automati-
cally when the wireless LAN client
moves.
Ethernet LAN
AP-12
[CH 11]
Access point switches
when wireless LAN
client is moved.
Set the channels at least four chan-
nels apart to avoid interference.
moving
Wireless LAN
client
CH:Channel
I Bridge mode A (Peer-to-Peer)
Connects two wired LAN via the AP-
12.
Only AP-12’s whose MAC address is
registered to one another, can be
accessed.
CH: Channel
Ethernet LAN:1
00-90-C7-27-00-01
AP-12
[CH11]
Ethernet LAN:2
[CH11]
AP-12
00-90-C7-27-00-02
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
1
I Bridge mode B (Client Mode)
Connects wireless LAN terminal or
the AP-12 (2) connected LAN system
via the AP-12 (1) in access point
mode.
CH:Channel
[CH11]
AP-12 (1)
Ethernet LAN:1
00-90-C7-27-00-01
- Only the AP-12 works as the access
point.
- Register the desired AP-12’s MAC
address, prior to communication,
with AP-12 (2) when two or more
AP-12’s operating in access point
mode are available.
AP-12 (2)
Ethernet LAN:2
Wireless LAN card
I Bridge mode C (Multi-site)
Connects two or more wired LAN via
the AP-12.
- It is not necessary to register the
MAC address and communicate
with other AP-12s easily.
CH:Channel
Ethernet LAN:1
[CH11]
AP-12
[CH11]
[CH11]
AP-12
1
AP-12
- To avoid communication speed slow
down, it is recommended to use up
to 10 AP-12’s only during heavy traf-
fic.
Ethernet LAN:2
Ethernet LAN:3
I About a MAC address
A MAC address is described on the
serial number seal. (See the figure at
right)
In bridge mode A, you need to register
your MAC address to the wireless
devices with which you communicate.
In bridge mode B, register the desired
wireless LAN device’s MAC address
prior to communication with your AP-
12.
Serial number seal
xxxxxxxxxxxx
MAC address
The AP-12’s MAC address can be
checked with [AP-12 Manager] also.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
1
1-2 Unit description
r
q
w
e
AP-12
t
The antenna is
built into the AP-12.
q Power indicator
r Ethernet ports
Lights when the power is ON.
➥ This is an RJ-45 type Ethernet
port.
w Wired LAN indicator
➥ Connect to a HUB using the sup-
plied patch cable.
➥ Connect to a PC using the sup-
plied crossover cable.
➥ Lights when the LAN (Ethernet)
connection is correct.
➥ Flashes when the AP-12 is com-
municating with the LAN.
• It does not light when the AP-12
does not recognize the Ethernet
port connection.
t DC jack
➥ Connect the supplied AC adapter.
• Make sure the LAN cable is con-
nected to the Ethernet port.
e Wireless LAN indicator
➥ Flashes when the power is ON.
➥ Flashes high speed while com-
municating data.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
1
1-3 Accessory attachment
I Leg pads/fixing sheet attachment
Use the leg pads on the bottom of
the AP-12 as below to place it on a
flat surface
Use the fixing sheets to secure the
AP-12 on a shelf.
Remove the protective paper before
attaching the sheet.
1
I To avoid falling
When mounting the AP-12 high on a
shelf or the like, secure it using a
cable fastener or tie to prevent the
AP-12 from accidental falling.
AP-12
NOTE: Do not tie and fix the DC
power cable and Ethernet cable
with a metal binder, such as a wire.
The cable may damaged and a
short circuit may occur.
Ferrite core
Fastener or tie
(purchase locally)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
1
1-3 Accessory attachment (continued)
I To avoid interference
Do not detach the ferrite core from both the AC adapter and the Ethernet cable.
Otherwise interference may occur when you use these items without the ferrite
core.
D AC adapter
D Ethernet cable
AC adapter (supplied)
To the AP-12
Ethernet cable
(supplied)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
1
1-4 Installation location
The transmission range and speed may change according to the installation location.
Installing the AP-12 in wide, open air with clear line of sight (example; a high place)
is recommended.
Approximate operating range at 11 Mbps speed is 30 m (98 ft) for indoor operation.
I Examples of recommended installation
On a desktop PC
On a shelf
I Examples of installation not recommended.
(Transmission range and speed may decrease)
1
Do not install with the unit dangling down
Do not install behind objects
I Installation precautions
Select a location as high as possible to keep a clear line of sight.
Install on a stable, flat surface without a slant, and no vibrations as the unit may fall.
Please be reminded of the following points for installation.
• NEVER put anything on the AP-12, nor stack the AP-12s on top of each other.
• Floors generally have steel girders and are installed with metal fire protection mate-
rial. Consequently, communication between different floors is often not possible.
• The transmission range is the widest in an open space. However, the signal may
be reflected from large metal walls in such a location as a warehouse.
• Radio signals will pass through walls and glass but not through metal. Concrete
walls may be reinforced with steel or other metal material that will block the signal.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE INSTALLATION
1
1-5 About the Ethernet card
An Ethernet port is necessary in your PC for set up.
Check that an Ethernet port is available with your PC before setting up.
• If no Ethernet port is available, purchase a suitable Ethernet card separately
according to the slot type.
I Desktop PC
Install the Ethernet card into an expansion slot.
Several types of expansion slots are available, such as PCI, ISA, etc.
Therefore, check the vacant expansion slot type before purchasing the Ethernet
card.
Ethernet card
Expansion slot
I Notebook PC
Install the Ethernet PC card into the PC card slot.
Check the Ethernet PC card type in the specifications of the PC card slot before
installing.
Ethernet card
PC card slot
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING AN IP ADDRESS
FROM THE DHCP SERVER
Chapter
2
This chapter describes setting instructions when setting up the AP-12’s IP address via the
DHCP server (default setting in “IP Configuration”).
See Chapter 3 when using the fixed IP address for the AP-12 or return to the default set-
ting.
2-1 Connecting to a LAN ………………………………………………………………10
2-2 Installing [AP-12 Manager] ………………………………………………………11
2-3 Starting [AP-12 Manager] …………………………………………………………13
I [AP-12 Manager] Settings Screen ………………………………………………14
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING AN IP ADDRESS FROM THE DHCP SERVER
2
2-1 Connecting to a LAN
This section enables a DHCP server to assigns an IP address automatically.
[Procedure]
q Connect the AP-12 and LAN with the supplied patch cable.
w Connect the AC adapter to the AC outlet to turn the AP-12 power ON.
• POWER indicator and wired LAN indicator on the top panel lights.
• Wireless LAN transmission indicator on the top panel flashes.
HUB
=
×
×
×
×
AP-12
Cross Port
Ferrite core
192.168.1.10
Connect to the LAN
with a DHCP server,
such as a router type
modem.
Patch cable (supplied)
When connecting to the broadband router,
connect the Ethernet cable from the AP-12
to the [LAN] port of the router.
Server:192.168.1.1
Automatically assigned range
192.168.1.10 to 192.168.1.15
AP-12
192.168.1.11
192.168.1.12
D About DHCP server detection
The AP-12 searches the DHCP server automatically to connect with a wired LAN
in which the DHCP server exists in. When no DHCP server is found within 30 sec.
(approx.) from power ON, the default IP address is used for the AP-12.
The default IP address is “192.168.0.1”. However, when a DHCP server is found in
the network, the AP-12 use the IP address obtained from the server.
Once the AP-12 power is turned OFF, then ON again, the AP-12 starts searching
for the DHCP server for 30 sec. (approx.) again.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING AN IP ADDRESS FROM THE DHCP SERVER
2
2-2 Installing [AP-12 Manager]
When installing into a Windows XP or Windows 2000 environment, log on as the
administrator.
q Quit all applications when Windows is running.
w Insert the CD into the CD-ROM drive.
The Auto Run function will be activated
and the main menu will appear on the
screen as at right.
If the main menu does not appear,
double-click the “AutoRun.exe” con-
tained in the CD.
e Click [Install Utility].
r Click <Next>.
2
Click
t Verify the directory in which you want to install to, then click <Next>.
• Click <…> and select the desired directory, if necessary.
Click
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING AN IP ADDRESS FROM THE DHCP SERVER
2
2-2 Installing [AP-12 Manager] (continued)
y When the dialog “Create new directory?” appears, click <OK>.
u Click <Install>.
Click
i Click <Finish>.
• The installation is now completed.
Click
o Click <Exit> to close the main
menu.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING AN IP ADDRESS FROM THE DHCP SERVER
2
2-3 Starting [AP-12 Manager]
This section describes about the verification of the IP address obtained, using the
[AP-12 Manager].
• Supposing that the connection between the LAN and AP-12 has already been done
in this section.
• Quit [Easy Setting Wizard] when it is running.
[Procedure]
q Click <Start> and select [AP-12 Manager] from the [Program menu].
w Click <Search>, then verify the IP address obtained.
• When no IP address is displayed, click <Search> again.
Verify
Click
2.
1.
2
e Click the desired access point name and then click <Connect>.
• [AP-12 Manager] Setting screen (p. 14) appears on the screen.
Displays the connected
AP-12’s IP address
1.
Click
2. Click
About AP-12 icon:
An icon is displayed on the task bar while the
[AP-12 Manager] is activated.
Right-click the icon and select “Connect to access point” from the menu to open the
[AP-12 Manager] setting screen.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING AN IP ADDRESS FROM THE DHCP SERVER
2
2-3 Starting [AP-12 Manager] (continued)
I [AP-12 Manager] Setting Screen
After installing [AP-12 Manager], the following screen appears first.
q to r are common buttons in the [AP-12 Manager] screen.
q
w
e
r
q <Restore default>
e <Cancel>
Restores all the contents of the
screen to the default settings.
The AP-12 searches the DHCP serv-
er and sets an IP address obtained
from the server.
Cancels the value or condition of all
contents registration in the screen
and closes the screen.
r <Apply>
Registers the value or condition of all
contents in the screen only. The
screen is kept open.
See Chapter 3 to restore completely.
w <OK>
Registers the value or condition of all
contents in the screen to the AP-12
and closes the screen.
To exit [AP-12 Manager]
Move the cursor on the icon in the task bar then right-click.
Select “Exit” in the menu that appears.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS
SETTING
Chapter
3
This chapter describes how to set the fixed IP address to the AP-12 or restore to the
default setting.
3-1 Connecting to the PC………………………………………………………………16
3-2 Using [Easy Setting Wizard] ……………………………………………………17
3-3 Installing [AP-12 Manager] ………………………………………………………25
3-4 Starting [AP-12 Manager] …………………………………………………………27
I [AP-12 Manager] Settings screen ………………………………………………29
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-1 Connecting to the PC
[Procedure]
q Connect the AP-12 and the PC with the supplied crossover cable.
• Use the supplied patch cable (3 m: 9.8 ft) when connecting the AP-12 and the
PC via a HUB.
NOTE: DISCONNECT THE PC FROM THE EXISTING LAN.
When the PC is connected to the existing LAN, the AP-12 searches the DHCP
server and uses the IP address obtained from the server according to the
default setting.
w Connect the supplied AC adapter to the AP-12 and an AC outlet.
• The Power indicator lights.
• The wireless LAN indicator flashes.
e Start up the PC.
• The wired LAN indicator on the top panel lights.
Check the Ethernet cable if the wired LAN indicator does not light.
Ferrite core (supplied)
Ethernet cross
cable (supplied)
Ferrite core (supplied)
AC adapter
(supplied)
AC outlet
Ethernet port
R
AP-12
DC jack
16
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-2 Using [Easy Setting Wizard]
Changing the PC’s IP address is necessary using [Easy Setting Wizard] when set-
ting up the AP-12. [Easy Setting Wizard] is contained in the utility CD and it allows
easy setting for changing the IP address.
[Procedure]
q Quit all applications when Windows is running.
w Insert the CD into the CD-ROM drive.
The Auto Run function will be activated
and the main menu will appear on the
screen as at right.
If the main menu does not appear,
double-click the “AutoRun.exe” con-
tained in the CD.
e Click [Easy Setting Wizard].
r Click <Next>.
3
Click
D About [Easy Setting Wizard]
The original IP address remains, there-
fore, the PC can be used in the previ-
ous setting condition after the AP-12
set-up.
• [Easy Setting Wizard] can be started
up from the supplied CD drive only.
(Unable to install.)
• When a new network is built, the IP
address of the PC using the AP-12,
must be changed.
[Easy Setting Wizard] enables the PC
to access the AP-12 temporarily with-
out changing the PC’s IP address.
The wizard searches for both the AP-
12 and PC’s address settings automat-
ically.
When the PC is unable to access to the
AP-12, the wizard assigns a tentative
IP address to the PC.
Refer to Chapter 6 (p. 51) for details.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-2 Using [Easy Setting Wizard] (continued)
t Click <Next> to start searching the AP-12.
Click
y Click the desired access point name you want to set up, then click <Next>.
• The default IP address is [192.168.0.1]. However, once the AP-12 has been con-
nected to a LAN with a DHCP server, a different IP address may be obtained.
The IP address
of the AP-12 ap-
pears.
1. Click
2. Click
When no access point is found:
When the error dialog “Cannot connect to the access
point” appears after approx. 30 sec.
➥ Check the connection between the AP-12 and the PC.
(p. 16)
➥ The network part may be different between the AP-12 and the PC in case the
access point has been used with the fixed IP address. Refer the Chapter 7-4 (p.
61) in such a case.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
u When the PC cannot access the AP-12 due to a network address difference
between them, the following screen appears.
Enter the desired unique host address for the PC, then click <Next>.
• When the PC can access the AP-12, the screen described in step !
• The default IP address of the AP-12 is “192.168.0.1”.
• Enter a value other than “1” in the address box.
2
appears.
Enter
Click
1.
2.
D About IP Address
• Assign the same network to the all
network devices in the same group.
• Assign an unique host address for
each device in the same group.
• NEVER assign a “network address”
(host address is 0 or starting from 0.)
• NEVER assign a “broadcast address”
(host address is 255).
The IP addresses consist of two ele-
ments, network part and host address.
For example, “192.168.0.1” (default IP
address of the AP-12; class C) has
the network part “192.168.0” and host
address “1”. Network devices, such as
the PC, with the same network part
are recognized in the same network,
and the each device is distinguished
by the host address. Pay attention to
the notes at right when obtaining IP
addresses.
3
19
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-2 Using [Easy Setting Wizard] (continued)
i Select [Restart Windows now] and click <Finish>.
• The PC will restart.
1. Click
2. Click
o [Easy Setting Wizard] will restart automatically.
• Click <Next>.
Click
20
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
!
0
Click <Next>.
Click
!
1
Click the access point, selected in step u, and click <Next>.
• The default IP address of the AP-12 is “192.168.0.1”.
3
Click
Click
1.
2.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-2 Using [Easy Setting Wizard] (continued)
!
2
Select [Use a fixed IP address] and click <Next>.
• The screen in step ! appears when [Use dynamic IP address alloc] is selected.
4
Select
Click
1.
2.
!
3
Enter the IP address and subnet mask for the AP-12.
• The network part must be the same as the PC IP address, and the host address
must be different from the other devices.
• Click <Next>.
Enter
1.
2.
The end of
Subnet Mask
can not be
changed.
Click
22
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
!
4
Set the ESS ID, then click <Next>.
The default ID (LG) is used in this example.
• The AP-12 can communicate with the unit in which the same ESS ID as the AP-
12 and wireless LAN card is set.
• Click <Next> without changing the ESS ID, if desired.
The ESS ID is
changeable later.
See p. 33 for details.
Click
!
5
Set the channel number, then click <Next>.
The default channel (11) is used in this example.
• The same channel should be selected for the Bridge A or C operation.
• Click <Next> without changing the channel, if desired.
3
The Channel is
changeable later.
See p. 33 for details.
Click
23
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-2 Using [Easy Setting Wizard] (continued)
!
6
Click <Next> to apply the settings to the AP-12.
Click
!
7
Click <Finish>.
Click
!
8
When the dialog “Reboot now?” appears on the screen, click <Yes>.
• When the PC can be connected to the AP-12 in step u, this dialog does not
appear on the screen.
Click
!
9
The PC reboots.
• After rebooting, the original IP address remains when a tentative IP address is
assigned in step u.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-3 Installing [AP-12 Manager]
This section describes the settings utility, [AP-12 Manager], installation.
[Procedure]
When installing into Windows XP or Windows 2000 environment, log on as the admin-
istrator.
q Quit all applications when Windows is
running.
w Insert the CD into the CD-ROM drive.
The Auto Run function will be activated
and the main menu will appear on the
screen as at right.
If the main menu does not appear,
double-click the “AutoRun.exe” con-
tained in the CD.
e Click [Install Utility].
r Click <Next>.
3
Click
t Verify the directory in which you want to install to, then click <Next>.
• Click <…> and select the desired directory, if necessary.
Click
25
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-3 Installing [AP-12 Manager] (continued)
y When the dialog “Create New Directory” appears, click <OK>.
u Click <Install>.
Click
i Click <Finish>.
• The installation is now completed.
Click
o Click <Exit> to close the
menu.
!
0
Start [AP-12 Manager].
• See next page if the AP-12
is connected to the PC.
• See Chapter 2-3 (p. 13) if
you reconnect the AP-12 to
a LAN network via a HUB.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-4 Starting [AP-12 Manager]
This section describes how to start up [AP-12 Manager].
• Quit [Easy Setting Wizard] when it is running.
[Procedure]
Be sure to install [AP-12 Manager] to the PC.
q Click <Start> and select [AP-12 Manager] from the [Program menu], then click
<Search>.
• When no IP address is displayed, click <Search> again.
Click
w Click the access point name and then click <Connect>.
3
• [The AP-12 Manager] Settings screen (p. 29) appears on the screen.
Displays
the
connected AP-
12’s IP address.
Click
1.
2. Click
About AP-12 icon:
An icon is displayed on the task bar while [AP-12
Manager] is activated.
Right-click the icon and select “Connect to
access point” from the menu to open [AP-12 Manager] Settings screen.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
3-4 Starting [AP-12 Manager] (continued)
e When the error dialog “Cannot connect to the access
point” appears on the screen, each AP-12 and the PC’s
network IP address may be different. In such a case,
click <OK> and close the dialog. Then, exit [AP-12
Manager].
To exit the AP-12 Manager:
Move the cursor on the icon in the task bar, then right-
click. Then select “Exit” in the menu that appears.
r Follow the steps q to i in Chapter 3-2 (p. 17) to set up
the PC again.
t The following screen appears after rebooting.
Click <Cancel>.
Click
y Follow the steps q and w in Chapter 3-4 (p. 27) to re-starting [AP-12 Manager]
again.
• [AP-12 Manager] Settings screen as in page 29 is displayed when the setting is
successful.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
FIXED IP ADDRESS SETTING
3
I [AP-12 Manager] Settings screen
After installing [AP-12 Manager], the following screen appears first.
q to r are common buttons in the [AP-12 Manager] screen.
q
w
e
r
3
q <Restore default>
e <Cancel>
Restores all the contents of the
screen to the default settings.
The AP-12 searches the DHCP serv-
er and sets the IP address obtained
from the server.
Cancels the value or condition of all
contents registration in the screen
and closes the screen.
r <Apply>
Registers the value or condition of all
contents in the screen only. The
screen is kept open.
w <OK>
Registers the value or condition of all
contents in the screen to the AP-12
and closes the screen.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
Chapter
4
This chapter describes for the details of [AP-12 Manager].
See Chapter 1 (p. 1) or 2 (p. 9) for installing and starting details of [AP-12 Manager],
according to the operating mode.
4-1 [AP-12 Manager] screen descriptions …………………………………………32
I Settings ……………………………………………………………………………32
I IP Configuration …………………………………………………………………36
I MAC security………………………………………………………………………37
I Wep security ………………………………………………………………………38
I Show Station ………………………………………………………………………40
I Version Information ………………………………………………………………41
I Options ……………………………………………………………………………42
4-2 The default settings ………………………………………………………………43
4-3 Uninstalling [AP-12 Manager] ……………………………………………………44
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-1 [AP-12 Manager] screen descriptions
I Settings
e
r
q
w
i
t
y
u
o
Click OK or Apply
to register the con-
tents of the setting.
Shows the AP-12’s MAC address.
q MAC address………
The address is also mentioned on the serial number
seal.
• The MAC address cannot be changed.
• The MAC address is a unique address that is
assigned to each device in the network.
Enter the desired alphanumeric name to discriminate
one AP-12 from another.
The name should be unique, and up to 29 characters
can be used.
w Name ………………
e Regulatory …………
Shows the regulatory name of the AP-12.
The regulatory name cannot be changed.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
Select the desired channel number for the wireless
communication. (default: 11)
r Channel ……………
• The same channel number should be selected with
another AP-12 when Bridge mode A or C is selected.
• Wireless LAN clients will detect the channel of the
AP-12 automatically and select it by themselves in
Bridge mode B operation.
Enter the desired ID for wireless network groups.
Up to 32 alphanumeric characters (case sensitive) can
be entered (default: LG).
• The ID entering is not possible when Bridge mode A
or C is selected in o Functional mode.
t ESS ID ……………
y RTS Threshold ……
Select the packet size for negotiation of data trans-
mission from 500 bytes, 1000 bytes and Off. When the
transmission packet size exceeds the selected value,
Rts (Request to send) and Cts (Clear to send) data is
transmitted to prevent communication speed deterio-
ration from the “Hidden wireless client” access.
See p. 35 for “Hidden wireless terminals”.
u Fragmentation
Select the packet size for the fragmentation operation.
(default:OFF)
Threshold …………
This setting improves total data transmission speed by
sending fragmented data, not all, when the communi-
cation is disconnected, such as that caused by inter-
ference.
4
Select the data transmission speed from 11 Mbps
i Rate ………………
(fixed) and automatic.
(default:11 Mbps/fixed)
When automatic is selected (“ꢀ” mark appears), the
data transmission speed is selected from 11, 5.5, 2
and 1 Mbps automatically according to the conditions.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-1 [AP-12 Manager] screen descriptions
I Settings (continued)
e
r
q
w
i
t
y
u
o
“Remote MAC Address” or “Preferred
Bssid” is displayed here according to
the selected functional mode.
Select the wireless LAN functional mode.
(default: Access Point)
o Functional mode …
See Chapter 1-1 (p. 2) for details of each mode.
NOTE: When “Auto-
matic” is selected in IP
configuration (p. 36),
bridge mode B is not
selectable.
The following items appear when you select Bridge
Mode A or B.
• Remote MAC Address
“Remote MAC Address” appears when Bridge Mode
A (Peer-to-Peer) is selected.
Enter the desired MAC address into the text box at
right for communication.
• Preferred Bssid
“Preferred Bssid” appears when Bridge Mode B
(Client Mode) is selected.
Enter the desired AP-12’s MAC address, prior to
communication, when two or more AP-12s operating
in access point mode are available.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
D Hidden wireless terminals
During Access Point mode communication as shown below, wireless LAN termi-
nal [A] and [C] cannot communicate directly, even when both terminal [A] and [C]
can access AP-12 [B].
In such a case, terminal [A] is a “Hidden wireless terminal” for [C], and terminal [C]
is a “Hidden wireless terminal” for [A].
When terminal [A] is accessing AP-12 [B], for example, to prevent the communi-
cation collision, the request-to-send (Rts) signal received by AP-12 [B] sends a
clear-to-send (Cts) signal to both terminal [A] and [C] repeatedly. Then terminal [C]
recognizes that AP-12 is busy, and forbidding to access to AP-12 [B].
Communication
collision
AAPP--1122 [[BB]]
wwiirreelleessss ttrraannssmmiissssiioonn aarreeaa
Ethernet LAN
A
C
AP-12 B
wireless LAN [C]
wireless transmission area
wireless LAN [A]
wireless transmission area
D Communication channels
Set the communication channels of network groups at least four channels apart to
avoid interference if two or more access points are available in the wireless trans-
mission area.
4
Otherwise, interference may occur due to partial overlap in bandwidth as shown below.
Channel settings of 1-6-11, for example, eliminates the possibility of interference.
6 channel
7 channel
8 channel
9 channel
10 channel
11 channel
1 channel
2 channel
3 channel
4 channel
5 channel
2400
2410 2420 2430 2440 2450 2460 2470 2480 2490 2500
Frequency (MHz)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-1 [AP-12 Manager] screen descriptions (continued)
I IP Configuration
Set the IP address of the AP-12.
q
w
Click <OK> or <Apply>
to register the setting.
Set the desired IP address, Subnet mask and
Gateway.
q Manual settings……
• The default settings are;
IP Address : 192.168.0.1
Subnet mask : 255.255.255.0
Gateway
: 0.0.0.0
• The end of Subnet Mask can not be changed.
• It is not necessary to set Gateway.
Obtain an IP address from the DHCP server in the
LAN. (default)
w Automatic …………
NOTE: When Bridge
mode B is selected in
Settings screen (p.
34), “Automatic” is not
selectable.
• Ethernet (default)
Obtain an IP address via wired LAN.
• Wireless
Obtain an IP address via Wireless LAN.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
I MAC security
Sets MAC address security function.
This function can only be set when the access point mode or Bridge mode C is
selected.
q
w
e
Click <OK> or <Apply>
to register the setting.
q Enable mac security
Turns the MAC security ON and OFF. (“ꢀ” mark
appears when set to ON.)
………………………
4
(default: OFF)
When the Mac security is turned ON, the wireless
devices to which a MAC address is registered only can
access the AP-12.
Up to 40 MAC addresses can be registered.
Displays the contents of the settings.
w Refresh ……………
e Remove All ………
Deletes all registered MAC addresses.
Click <Remove All > then <Apply>, when deleting all
settings.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-1 [AP-12 Manager] screen descriptions (continued)
I Wep Security
(Setting for data security.)
e
q
w
Click <OK> or <Apply>
to register the setting.
Turn the WEP transmission data encryption ON and
OFF, and select the encryption level from 64-bit and
128-bit. (“ꢀ” mark appears when the encryption is set to
q Wep settings ………
ON.)
(default: OFF)
• 64 bits/128 bits
Encrypt the character string, entered in w key gen-
erator, at 64-bit/128-bit.
Enter the desired character string for data encryption
and decryption.
w Key generator ……
Up to 32 alphanumeric characters (case sensitive) can
be entered.
The generated four keys (may differ according to the
selected bit number in q Wep setting), are displayed
in the Wep keys text boxes.
- The same character string should be entered for all
the AP-12’s or terminals, to be accessed.
- After clicking <OK>, all WEP key indications in the
Wep keys text boxes return to “00 00 00 00 00.”
38
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
Select the desired WEP key number for data encryp-
tion. (default:1)
e Wep keys …………
The desired key number can be selected between the
AP-12 and another AP-12 or terminal.
A key, generated by the key generator, is displayed in
the text boxes. However, the desired keys in hexa-
decimal numbers can be entered into the text boxes
directly when no key generator is set.
The lower 40-bit (10 hexadecimal numbers) or the
lower 104-bit (26 hexadecimal numbers) can be
entered when 64 bits or 128 bits is selected, respec-
tively.
- No key generator is displayed when the desired key
is entered into the key text boxes directly.
- The same key content should be entered into the key
number that is selected for another AP-12 or termi-
nal, as shown in the example 1 and 2.
No communication is made when different contents
are entered into the key number that is selected for
another AP-12 or terminal, as shown in the example
3.
D WEP Key Setting Examples– 64-bit encryption
Example 1
Two-way communication
enable
4
Example 2
Example 3
Two-way communication
enable
Communication disable
NOTE: Above screens shows the condition before clicking <Apply>.
The display returns to “00 00 00 00 00” after clicking <Apply>.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-1 [AP-12 Manager] screen descriptions (continued)
I Show Station
Shows all MAC address for registered terminals during access point mode operation.
Refresh ……………
Renews the MAC address indication.
• [AP-12 Manager] recognizes a terminal is still con-
nected for 5 minutes (approx.) after the disconnec-
tion.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
I Version Information
Shows the version number for the [AP-12 Manager] and the firmware.
(>>) links to Icom home page.
4
41
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-1 [AP-12 Manager] screen descriptions (continued)
I Options
q
w
e
r
Click <OK> or <Apply>
to register the setting.
q Show splash screen
at startup …………
Turns the splash screen ON and OFF.
The screen appears when starting up [AP-12
ꢀ
Manager].
(default: /Display)
Selects [AP-12 Manager] icon indicating type from
w Animate icons ……
e Set password………
flashing or non-flashing. The icon flashes when
ꢀ
checked (“ꢀ” appears).
(default: /Flash)
Turns the password function ON and OFF when start-
ing up [AP-12 Manager].
The password setting screen is displayed when re-start-
ing [AP-12 Manager] after setting to ON (“ꢀ” appears).
Enter the desired password within 32 characters (case
sensitive).
Once the password is set, password entry is neces-
sary for starting up [AP-12 Manager].
(default: OFF)
Selects the entered key generator and WEP key indi-
cation type. The entered characters are displayed with
asterisks (*) when this item is checked (“ꢀ” appears).
(default: OFF)
r Mask user input
…
42
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-2 The default settings
The default settings of [AP-12 Manager] are shown below.
I Settings
• Mac address
: The MAC address is described on the serial num-
ber seal. (The setting in this field cannot be
changed.)
• Name
: AP-12
• Regulatory
• Channel
: FCC (The setting in this field cannot be changed.)
: 11
• ESS ID
: LG
• RTS Threshold
• Fragmentation Threshold
• Rate
: OFF
: OFF
: 11 Mbps/static
: Access Point
• Function Mode
I IP Configuration
(Ó) Manual Settings
(G) Automatic (selected)
• (G) Ethernet (selected)
• IP Address
: 192.168.0.1
• Subnet Mask : 255.255.255.0
• (Ó) Wireless
• Gateway
: 0.0.0.0
I MAC security
• Enable mac security
N.1 to N.40: 00-00-00-00-00
I Wep Security
• Wep Enabled
• Key generator
• WEP keys
: OFF
: Blanked
: 1
: OFF
4
I Options
• Show splash screen at startup
• Animate icons
ꢀ
ꢀ
:
:
/Display
/Flash
• Set password
• Mask user input
: OFF
: OFF
43
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-12 MANAGER
4
4-3 Uninstalling [AP-12 Manager]
This section describes [AP-12 Manager] uninstallation. (Windows XP)
When your PC uses an operating system other than Windows XP, follow the on-
screen messages or instructions for the OS to uninstall.
[Procedure]
q Click <Start> and select [Control Panel] from the [Settings] menu.
Double-click <Install/Uninstall>.
w Click [Add or Remove Programs] and select [ICOM AP-12 Manager] and click
<Change/Remove...>.
Select
Click
1.
2.
e [AP-12 Manager] Uninstall Wizard starts automatically.
Click <Uninstall>.
Click
The uninstall wizard appears when operating according to the installation instruc-
tion, described in Installing [AP-12 Manager] (pgs.11, 25).
After uninstalling, install [AP-12 Manager] with the install wizard appeared after the
uninstallation.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING EXAMPLES
Chapter
5
This chapter describes the minimum setting requirements in each functional mode
with a setting example.
5-1 Access point mode ………………………………………………………………46
5-2 Bridge mode A (Peer to Peer) ……………………………………………………47
5-3 Bridge mode B (Client Mode) ……………………………………………………48
5-4 Bridge mode C (Multi-site)…………………………………………………………49
<Function List >
The functions available will change according to the selected functional mode.
✔: Available N/A: Not Available
Bridge mode B
Access point mode Bridge mode A
Bridge mode C
Roaming
N/A
N/A
✔
✔
DHCP client
WEP security
MAC security
ESS ID
✔
✔
✔
✔
✔
✔
✔
✔
N/A
✔
✔
N/A
N/A
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING EXAMPLE
5
5-1 Access point mode
Set the AP-12 and the PC as in the net-
work shown at right.
HUB
AP-12
• IP address of the PC should already be
set. (See Chapter 2 or 3)
• See Chapter 4 (p. 31) for [AP-12
Manager] details.
wireless
terminal
wired terminal
wired terminal
1.Setting the AP-12
Set the following items in [AP-12 Manager] Settings screen. (pgs. 33, 34)
• ESS ID:
Set the same ID as the wireless terminal.
• Channel:
Set the desired channel.
- Set the channel at least four channels apart to avoid interference if another AP-
12(s), operating on an other channel(s), are within the transmission area.
• Functional mode:
Select “Access Point”.
Check the “Auto Rate Fallback” (“ꢀ” appears) when communication is unstable.
2.Setting the wireless terminal
Set the following items in the wireless LAN card.
• Network settings:
Select “Infrustructure”.
• ESS ID:
Set the same ID as the AP-12.
• Tx rate:
Select “Automatic”.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING EXAMPLE
5
5-2 Bridge mode A (Peer-to-Peer)
Set the AP-12 and the PC as
in the network shown at right.
wired terminal
wired terminal
HUB
AP-12 (1)
• IP address of the PC should
Example
already be set. (See Chapter
00-90-C7-27-00-01
2 or 3)
• See Chapter 4 (p. 31) for
[AP-12 Manager] details.
HUB
Printer server
AP-12 (2)
Example
00-90-C7-27-00-02
wired terminal
Printer
1. Common settings
Set the following items in [AP-12 Manager] Settings screen (pgs. 33, 34).
• Channel:
Set the desired channel for both the AP-12s.
- Set the channel at least four channels apart to avoid interference if another AP-
12(s), operating on an other channel(s), are within the transmission area.
• Functional mode
Select “Bridge Mode A”.
- Check the “Auto Rate Fallback” (“ꢀ” appears) when communication is unstable.
5
2. Individual settings
Set the partner’s MAC address in [AP-12 Manager] Settings screen. (p. 32)
• Remote MAC Address
Set the AP-12 (2)’s MAC Address, “00-90-C7-27-00-02”, to the AP-12 (1).
Set the AP-12 (1)’s MAC Address, “00-90-C7-27-00-01”, to the AP-12 (2).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING EXAMPLE
5
5-3 Bridge mode B (Client Mode)
Set the AP-12 and the PC as
in the network shown at right.
Printer server
• IP address of the PC should
already be set. (See Chapter
2 or 3)
• See Chapter 4 (p. 31) for
[AP-12 Manager] details.
• Follow the instruction manu-
al of the printer server when
connecting to the AP-12.
(Usually, a crossover cable
is used.)
Printer
To LAN
AP-12 (2)
AP-12 (1)
AP-12 (3)
HUB
wireless LAN
terminal
Example
00-90-C7-27-00-01
wired terminal wired terminal
1. Common setting
Set the following item in [AP-12 Manager] Settings screen. (p. 33)
• ESS ID:
Set the same ID.
- Check the “Auto Rate Fallback” (“ꢀ” is appears) when communication is unstable.
2. AP-12 (1) and (2) settings
Set the following items in [AP-12 Manager] Settings screen. (p. 34)
• Functional mode:
Select “Bridge Mode B.”
• Preferred BSS ID:
Set the AP-12 (3)’s MAC address, “00-90-C7-27-00-01,” prior to communication
with the AP-12 (3).
3. AP-12 (3) settings
Set the following items in [AP-12 Manager] Settings screen. (pgs. 33, 34)
• Channel:
Select the desired channel.
- Set the channel at least four channels apart to avoid interference if another AP-
12(s), operating on an other channel(s), are within the transmission area. (p. 35)
• Functional mode:
Select “Access Point.”
- AP-12 must be used for the access point when other AP-12s (AP-12 (1) and (2),
in this case) are used in “Bridge Mode B.”
48
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING EXAMPLE
5
5-4 Bridge mode C (Multi-site)
Set the AP-12 and the PC as in
the network shown at right.
LAN terminal
HUB
To LAN
• IP address of the PC should
already be set. (See Chapter 2
or 3)
• See Chapter 4 (p. 31) for [AP-
12 Manager] details.
To LAN
HUB
AP-12
HUB
To LAN
• Follow the instruction manual of
the printer server when con-
necting to the AP-12. Usually, a
crossover cable is used.)
LAN terminal
AP-12
AP-12
Printer server
Printer
All AP-12s settings
Set the following items in [AP-12 Manager] Settings screen. (pgs. 33, 34)
• Channel:
Set the desired channel.
- Set the channel at least four channels apart to avoid interference if another AP-
12(s), operating on an other channel(s), are within the transmission area. (p. 35)
5
• Functional mode:
Select “Bridge Mode C.”
- Check the “Auto Rate Fallback” (“ꢀ” appears) when communication is unstable.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONFIGURATION
Chapter
6
This chapter describes about changing the PC’s IP address.
Changing of the PC’s IP address is required when setting up a LAN used with the
AP-12 with a fixed IP setting and a PC.
The default IP address is used with the AP-12 (192.168.0.1) for the setting descrip-
tion in this chapter.
Changing the PC’s IP address is not necessary when the PC has been connect-
ed to a LAN with a DHCP server, and obtains an IP address from the DHCP serv-
er.
6-1 For Windows XP ……………………………………………………………………52
6-3 For Windows 98/98SE/Me…………………………………………………………54
6-2 For Windows 2000 …………………………………………………………………55
[Setting the IP address and subnet mask]
• Set a unique IP address for each PC in the network group.
• Set the same subnet mask for all PCs in the network group.
• Set private addresses. 192.168.0.0 to 192.168.255.255 are used for a small net-
work group (up to 253 terminals). However, never assign the network address
(192.168.XXX.0) and broadcast address (192.168.XXX.255) to the terminal.
(XXX: 0 to 255)
See the following address examples of a wireless LAN comprised of three PCs.
Wireless terminal A: 192.168.0.10 (subnet mask: 255.255.255.0)
Wireless terminal B: 192.168.0.11 (subnet mask: 255.255.255.0)
Wireless terminal C: 192.168.0.12 (subnet mask: 255.255.255.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONFIGURATION
6
6-1 For Windows XP
[Procedure]
q Boot up the PC.
• The log-on screen appears.
w Log on as the administrator.
e After the PC has booted up, click <Start> and select [Control Panel] from the
[Settings] menu.
r Click [Network and Internet Connections].
t Click [Network Connection].
y Right-click [Local Area Connection] icon and click [Properties] in the menu that
appears.
u Click [Internet Protocol (TCP/IP)] and then [Properties].
Click
1.
2. Click
52
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONFIGURATION
6
i Select [Use the following IP address] and enter the IP address and subnet mask,
then click [OK] to enable the specified settings.
Click
2. Enter
1.
3.
Click
6
53
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONFIGURATION
6
6-2 For Windows 98/98SE/Me
[Procedure]
q Click <Start> and select [Control Panel] from the [Settings] menu.
Click [Network].
w Verify that [TCP/IP−>The Ethernet card name] is displayed in the screen.
Click [TCP/IP] then, [Properties].
Click
1.
2. Click
e Click the [Specify an IP address] radio button, enter the IP address and subnet
mask and click <OK>.
Click
1.
2.
Enter
Click
3.
r When the message “Reboot now?” appears on the screen, click <Yes>.
After rebooting, the specified settings are available.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONFIGURATION
6
6-3 For Windows 2000
[Procedure]
q Start the PC.
• The Window 2000 log-on screen appears.
w Log on as the Administrator.
e Click <Start> and select [Network and Dial-up Connections] from the [Settings]
menu.
Then, double click [Local Area Connection] icon which shows your Ethernet card
name.
Double-click
r Click [Properties].
6
Click
55
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONFIGURATION
6
6-3 For Windows 2000 (Continued)
t Click [Internet Protocol (TCP/IP)] and then [Properties].
Click
Click
1.
2.
y Select [Use the following IP address] and enter the IP address and subnet mask,
then click [OK] to enable the specified settings.
Click
1.
2.
Enter
Click
3.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
Chapter
7
This chapter describes additional matters about the AP-12.
7-1 Troubleshooting ……………………………………………………………………58
7-2 Connecting the AP-12 and HUB…………………………………………………60
7-3 Verifying the connection to the AP-12 …………………………………………60
7-4 Failure in searching for the AP-12………………………………………………61
7-5 IP address confirmation …………………………………………………………64
I Windows XP ………………………………………………………………………64
I Windows 98/98SE/Me ……………………………………………………………65
I Windows 2000 ……………………………………………………………………65
7-6 Connection to the router type modem …………………………………………66
7-7 Specifications ………………………………………………………………………68
I Specifications for Ethernet Plug…………………………………………………69
I Wireless LAN for the AP-12 ……………………………………………………69
7-8 Glossary ……………………………………………………………………………70
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
7-1 Troubleshooting
If your AP-12 seems to be malfunctioning, please check the following points before
sending it to a service center.
PROGRAM
POSSIBLE CAUSE
SOLUTION
REF.
NO power comes DC Power cable or AC Re-connect the DC power pgs. 10,
ON.
adapter is improperly con- cable or AC adapter correctly.
nected.
16
Television interfer- • The AP-12 is too close to a • Keep the AP-12 away from p. 6
ence (TVI) or television set or radio. a television set or radio.
broadcast interfer-
ence (BCI) occurs.
Communication An IP address has not been Turn the AP-12 power OFF. —
with the AP-12 has obtained from the DHCP After waiting a few seconds,
failed.
server.
turn power ON again. Then,
reboot the PC(s).
Wired LAN indica- • Incorrect Ethernet cable is • Connect the correct Ethernet p. 16
tor does not light.
used.
cable according to the con-
necting condition.
• The HUB power is OFF, or the • Turn the HUB power ON, or pgs. 10,
patch cable is connected to connect the patch cable to
the cascade port of the HUB. the cross port of the HUB.
60
[AP-12 Manager] un- The PC is not logged on as Log on as the administrator.
able to be installed to the administrator.
pgs. 11,
25
Windows XP/2000.
Menu screen does Auto Run function does not Double-click “AutoRun.exe” pgs. 11,
not appear after in- function.
serting the CD.
contained in the CD.
17,
25
No connection to The network part of IP • When the AP-12 is connect- p. 13
the AP-12 via [AP- address for both AP-12 and ed to a LAN:
12 Manager].
PC are different.
Turn the AP-12 power OFF.
After waiting a few seconds,
turn power ON again. Then
start [AP-12 Manager].
• When the AP-12 is connect- p. 17
ed to the PC:
Quit [AP-12 Manager], set
the PC’s IP address again
using the [Easy Setting
Wizard], then restart [AP-12
Manager].
58
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
PROGRAM
POSSIBLE CAUSE
SOLUTION
REF.
Connection to the The network part of the AP- Reset the AP-12’s IP address pgs. 17,
AP-12 has failed 12’s IP address is different using [Easy Setting Wizard] 61
after restoring.
from the PC’s because of the or the [AP-12 Manager].
restoring.
No IP address is • Ethernet cable is not connect- • Turn the AP-12 power OFF. p. 10
assigned from the ed to wired LAN within 30 After waiting a few seconds,
DHCP server.
sec. from turning the AP-12 turn power ON again, then
power ON. check the IP address.
• “Manual settings” is select- • Select “Automatic” and con- p. 36
ed. nection method.
• No DHCP server is available • Confirm the DHCP server —
in the connected wired LAN. availability.
Wireless LAN ter- • No DHCP server is available • Confirm the DHCP server —
minal(s) unable to in the connected wired LAN. availability.
obtain an IP ad- • Fixed IP address is set to • Set the wireless LAN card to p. 36
dress from the wireless LAN card.
DHCP server via
obtain an IP address from
the DHCP server.
the AP-12.
• “Bridge Mode B” is selected • Select “Access Point Mode”, p. 34
as the Functional mode. “Bridge Mode A” or “C”.
“Automatic” is im- “Bridge Mode B” is selected Select “Access Point Mode”, p. 34
possible to set. as the functional mode. “Bridge Mode A” or “C”.
[AP-12 Manager] • The network part of the AP- • Set the AP-12’s IP address p. 62
or [Easy Setting 12’s IP address is different using [AP-12 Manager].
Wizard]
cannot from the PC’s.
find the AP-12.
• In case of using Windows • Right-click [Local Area p. 52
XP, “Enabled, Firewalled” is Connection] icon and click
indicated on the [Local Area [Properties]. Then, select
Connection] icon.
[Advanced] tab in the menu.
Clear the [Internet Connection
Firewall] check box.
• Set the software to enable —
• The personal firewall soft- access to the AP-12.
ware is activated. *See the software’s instruction
manual or for details.
7
Wireless commu- ESS ID or WEP security set- Set the same ESS ID or WEP pgs. 33,
nication is impos- ting is different between the security setting. 38
sible. units.
Communication “Adhoc” mode is selected with Select “Infrastructure” mode.
—
with wireless LAN the wireless LAN cable.
card via access
point mode has
failed.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
7-2 Connecting the AP-12 and HUB
There are 2 ways to connect the AP-12 and HUB
D Connect to the Cross Port
D Connect to the Cascade Port
HUB
HUB
=
=
×
×
×
×
×
×
×
×
Cascade Port
Cross Port
Crossover cable
(supplied)
Patch cable
(supplied)
AP-12
AP-12
• A port with a switch may be available that switches the cascade port use as cross
port, according to the HUB.
Be careful of the switch position and the connecting Ethernet cable type.
7-3 Verifying the connection to the AP-12
The IP packet received condition of the other PC can be easily checked by pinging
when the IP address for each terminal is set correctly.
Enter the following command in the MS-DOS window to verify by pinging.
“ping xxx.xxx.xxx.xxx”
✰ Ping command example
Enter the desired AP-12’s IP
address for “xxx.xxx.xxx.xxx”
Four pings (echo request) are
transmitted when executing the
command, and the reply mes-
sage will be received for each
ping.
When no reply is received, check
the terminal protocol availability,
AP-12 or wireless LAN card set-
tings, such as functional mode, ESS ID, etc.
The message “destination unreachable” will be displayed when both the IP address
and subnet mask are different between source and destination terminals.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
7-4 Failure in searching for the AP-12
Manual IP address setting is necessary when no AP-12 is found (the following
screen appears) using [Easy Setting Wizard] or [AP-12 Manager], even if the con-
nection between the AP-12 and the PC is correct.
• The following screen may take 30 sec. or more to appear.
D When using [Easy Setting Wizard]
D When using [AP-12 Manager]
Access point does not appear.
[Procedure]
q Connect the PC and the AP-12 directly using the supplied crossover cable.
NOTE: DISCONNECT THE PC FROM THE EXISTING LAN.
When the PC is connected to the existing LAN, the AP-12 searches the DHCP
server and uses the IP address obtained from the server according to the
default setting.
w Start [AP-12 Manager] (p. 27).
e Click <Set IP>.
• <Access point IP address setup tool> screen appears.
7
Click
61
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
7-4 Failure in searching for the AP-12 (continued)
r Enter the desired IP address for the AP-12. The network part must be the same
as the PC’s IP address.
t Enter the MAC address, described on the serial number seal.
y Turn the power OFF.
After waiting a few seconds, turn the power ON again.
u Click <Set IP>.
Enter
Enter
1.
2.
3. Click
i After 30 seconds (approx.: from clicking <Set IP>), click <Close> when the mes-
sage stating that the setting is completed appears.
• Do not turn the power OFF at this stage, as the setting will be erased and return
to the condition in step r.
Click
2.
1.
Verify
62
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
o Click <Search>.
Click
!
0
Select the AP-12, then click <Connect>.
• [AP-12 Manager] Settings screen appears.
Displays the connected
AP-12’s IP address
Click
1.
2. Click
!
1
Click [IP Configuration] and set the AP-12’s IP address as desired.
!
2
Click <OK> to register all the settings in the screen to the AP-12.
7
Set
1.
2. Click
63
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
7-5 IP address confirmation
When the PC’s IP address, including network part, is unknown, refer to the following
instructions for confirmation.
- Reset the desired fixed IP address manually, or obtain an IP address from the
DHCP server by connecting the PC to the LAN.
I Windows XP
[Procedure]
q Click <Start> and select [Control Panel] from the [Settings] menu.
w Click [Network and Internet Connection].
e Click [Network Connection].
r Right-click [Local Area Connection] icon and click [Status] in the menu that
appears.
Click
t Click [Support] tab and confirm the assigned IP address, then click <Close>.
• IP address assigned to the PC is displayed.
Click
1.
2.
Confirm
Click
3.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
I Windows 98/98SE/Me
[Procedure]
q Click <Start> and select [Run].
w Enter “winipcfg” and push [Enter].
e Click [M] and select the desired Ethernet card.
• IP address assigned to the PC is displayed.
Select
1.
2.
Confirm
I Windows 2000
[Procedure]
q Click <Start> and select [Program]. Then, click [Command prompt] from
[Accessory] menu.
w Enter “ipconfig” and push [Enter].
• IP address assigned to the PC is displayed.
7
Confirm
1.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
7-6 Connection to the router type modem
This section describes the connection between a router type modem and the AP-12
with the default setting.
There are different types of modems available—bridging type and router type.
IMPORTANT!: The AP-12 cannot be connected to a bridging type modem directly.
Bridging type modem: Usually connects one PC only and a global IP address is
assigned to the PC.
Router type modem: Multiple PC’s can be connected in the LAN via the HUB, and
a private IP address is assigned to the PC.
D Wireless terminal preparation
After the following preparation is completed, wireless communication can be made
with the AP-12 when using Icom’s wireless LAN card.
q Prepare the PC to use the wireless LAN card.
w Install the supplied wireless LAN card driver.
Install other applications or utilities if supplied.
• Refer to the instruction manual supplied with the LAN card for driver, applica-
tions and utilities installation.
e Install [AP-12 Manager].
• [AP-12 Manager] is used for IP address confirmation, AP-12 settings, etc.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
D Connection to the router type modem
[Procedure]
q Connect the AP-12 and the router type modem using the supplied patch cable.
w Connect the AC adaptor to turn the AP-12 power ON.
• The [POWER] indicator and the LAN indicator lights.
• The [Wireless LAN] indicator flashes.
* Check the Ethernet cable connection and type if the LAN indicator does not light.
e Start the PC and obtain an IP address from the modem automatically.
Router Type Modem
DC
Ethernet
MDI MDI-X
DSL
/CATV
INTERNET
Patch cable
(supplied)
AP-12
Wireless LAN card
Wireless LAN card
Connect the AC adapter after the
Ethernet cable is connected and then
turning the modem power ON.
7
When communication has failed.
Turn the AP-12 power OFF. After waiting a few seconds, turn the power ON again.
Then check the wireless terminal’s IP address using [AP-12 Manager].
See the Chapter 7-5 (p. 64) for IP address confirmation.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
7-7 Specifications
• Input power
: 7.5 V DC 5% (Negative grounding)
With supplied AC adapter is 90 to 132 V AC
• Current drain
: Transmit
Receive
400 mA (typical)
350 mA (typical)
• Operating temperature range
• Dimensions
: 0 to +55°C; +32 to +131°F
: 100.0(W)×30.5(H)×70.0(D) mm
15
3
3
3 ⁄16(W)×1 ⁄16(H)×2 ⁄4(D) in
(projections not included)
: Approx. 90 g; 3.2 oz
• Weight
• Standard
: IEEE 802.11b
• Compliance
• Communication method
• Spreading system
: FCC Part 15, Canada RSS-139
: Simple system
: Direct spread-spectrum communication
system
• Modulation
: DPSK, DQPSK
• Frequency range
• Available channels
• Data transmission rate
• Transmission range
• Security
: 2400 to 2472 MHz
: 11
: Max. 11 Mbps
: Approx. 30 m; 98.4 ft (indoor) at 11 Mbps
: WEP (Wired Equivalent Privacy)
MAC (Media Access Control)
*MAC: [Bridge Mode A] and [Bridge Mode B] is
not available.
• Transmission power
• Reception sensitivity
• Demodulation method
• Antenna type
: 100 mW or less
: –76 dBm max. (frame error rate: 8%)
: Digital demodulation (matched filter type)
: Diversity antenna (Built-in, non-replace-
ment)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
• LAN interface
: Ethernet plug (Type RJ-45)
Based on IEEE802.3/10BASE-T
: 10 Mpbs
: Status indicators (Power, Wired LAN,
Wireless LAN)
• Transmission rate
• User interface
• System requirements
: PC/AT compatible computer
Windows XP/Windows Me/Windows
2000/Windows 98 or Windows 98 SE.
* The stated specifications may be subject to change without notice.
* The transmission range may vary depending on the transmission speed and
the environmental conditions.
I Specifications for Ethernet Plug
Modular plug type RJ-45 (8-pin) ×1
1. Sending (+)
2. Sending (–)
1 2 3 4 5 6 7 8
3. Receiving (+) 4. Not used
5. Not used
7. Not used
6. Receiving (–)
8. Not used
* The stated specifications may be subject to change without notice.
I Wireless LAN for the AP-12
To communicate with the AP-12, the PC must be installed with Icom’s Wireless LAN
products for 11 Mbps.
• WEP security function is available with use during communication between Icom
products.
• Bridge Mode is not available except with Icom products.
• When functional mode is Bridge Mode B, select the AP-12 as the access point.
7
69
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
HUB
7-8 Glossary
A hub is required when the AP-12 and other devices
are used to construct a network. 10BASE-T or 100
BASE-TX cable is used for the connection to the
hub.
Access point
A generic name for devices or points to connect a
wired LAN and wireless LAN.
IP (Internet Protocol) address
BSS ID (Basic Service Set-IDentifier)
Specified wireless LAN in MAC class.
The ID is uses the MAC address that is assigned to
each network device.
32-Bit address to identify all the devices connected
to a network in which the TCP/IP protocol is used.
Usually, the IP address consists of four 8-bit numer-
ical character strings of decimal notation (e.g.,
192.168.0.1). A private IP address specified by a
network administrator does not need to apply to an
address administration agency or internet service
provider. However, the network administrator must
assign the private address according to the rules
below. The private address must be converted into
a global IP address when connecting to an external
network. The IP addresses below can be used as
the private IP address.
Client
A generic name for network devices which relay
packets at a MAC address level.
Crossover Cable
The transmission signal cable and receiving signal
cable are cross wired to communicate correctly.
Generally, used for connection between the PCs.
DHCP server
Class A: 10.0.0.0 to 10.255.255.255
Class B: 172.16.0.0 to 172.31.255.255
Class C: 192.168.0.0 to 192.168.255.255
DHCP (Dynamic Host Configuration Protocol) is a
protocol for a client to obtain necessary information
automatically from a server on the TCP/IP network.
The DHCP server controls IP address, default gate-
way, domain name, etc. as network information. AP-
12, which has the DHCP server function, obtains the
IP address, default gateway, DNS address, etc.
when the DHCP client (Computer) has started.
LAN (Local Area Network)
A relatively small-sized network in the same floor or
the same site.
MAC address (Media Access Control Address)
A physical address specified in individual wired or
wireless products. The network device manufactur-
ers control this address so that a unique number
can be assigned to only one product in the world.
Ethernet equipment and wireless LAN products
send and receive a frame according to this MAC
address.
ESS ID (Extended Service Set-IDentifier)
A name for identification to create several network
groups in a communication area in a wireless LAN.
In the wireless network group which communicates
to AP-12, the identifier of the wireless terminal must
be the same as that of AP-12.
Ethernet
Network
A LAN communication system developed by Xerox,
DEC and Intel. 10BASE-T, 100BASE-TX, 10BASE-
5, 10BASE-2, etc. are available depending on the
cable type.
The state that some devices such as a server, work-
station, Computer, etc. are connected to a commu-
nication system through a cable or ADSL line, to
transmit data.
Global IP address
Packet
A unique address assigned to a device. One global
IP address is assigned to only one device in the
world.
A unit to send/receive data. The packet consists of
a header, which contains information necessary for
sending/receiving, and data section which is the
data itself.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
7
Password
A character string which must be entered by a user
who is accessing a network because of network
security. If a password is set, the user cannot
access unless the user enters the valid password
correctly.
Patch Cable
The transmission signal cable and receiving signal
cable are wired straight to communicate correctly.
Generally used for connection between the PC and
HUB.
Protocol
Definition of procedure to execute send/receive data
in the communication.
Subnet mask
A subnet mask is used in one IP address as a net-
work address and host address. Assuming that the
IP address of a host is “192.168.0.1” and the subnet
mask is “255.255.255.0” multiply the IP address of
binary notation and subnet mask of binary notation
together, and the network address “192.168.0.0” is
obtained. Then, the remainder “1” is the host
address.
Traffic
Flow of packets on the network or load applied to
the network line (e.g., data transmitted through the
network line). As the traffic increases, the data
transmission rate may decrease or data may be
lost.
WEP (Wired Equivalent Privacy)
A function to encrypt, send and receive a wireless
LAN signal. This function can prevent wireless LAN
communication interception.
10BASE-T
One of the Ethernet standards. 10BASE-T achieves
the transmission rate of 10 Mbit/s with a twisted pair
cable.
7
100BASE-TX
One of the Ethernet standards. 100BASE-TX
achieves the transmission rate of 100 Mbit/s with a
twisted pair cable of Category 5.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
A-6165G-1EX
Printed in Japan
1-1-32, Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
2002 Icom Inc.
©
|