¨
Model No. 831.297820
Serial No.
The serial number is found in the location
shown below. Write the serial number in
the space above for future reference.
Serial Number
Decal
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the tread-
mill is not working properly.)
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 10.) You must be
able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
20. Inspect and tighten all parts of the treadmill
regularly.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
21. Never insert any object into any opening.
22. Always unplug the power cord before per-
forming the maintenance and adjustment pro-
cedures described in this manual. Never re-
move the motor hood unless instructed to do
so by an authorized service representative.
Servicing other than the procedures in this
manual should be performed by an authorized
service representative only.
16. To reduce the possibility of the treadmill over-
heating, do not operate the treadmill continu-
ously for longer than 1 hour.
17. Never leave the treadmill unattended while it
is running. Always remove the key when the
treadmill is not in use.
23. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown below has been placed on your treadmill. If the decal is missing, or if it is not legible,
please call our toll-free HELPLINE to order a free replacement decal (see the back cover of this manual).
Apply the decal in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for purchasing the HEALTHRIDER¨
SOFTSTRIDER LX treadmill. The new SOFTSTRIDER Time (excluding holidays). To help us assist you,
Monday through Saturday, 7 a.m. until 7 p.m. Central
LX combines advanced technology with innovative
design to let you enjoy an excellent form of cardiovas-
cular exercise in the convenience and privacy of your
home. And when youÕre not exercising, the unique
SOFTSTRIDER LX can be folded up, requiring less
than half the floor space of other treadmills.
please note the product model number and serial num-
ber before calling. The model number of the treadmill
is 831.297820. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our toll-free HELPLINE at 1-800-736-6879,
Water Bottle
Holder (Bottle
not included)
Reading
Rack
Console
Accessory Tray
Handrail
Handrail
Storage Latch
Key/Clip
LEFT SIDE
RIGHT SIDE
Cushioned Walking Belt
Hood
Circuit
Breaker
Foot Rails
Power Cord
Front Wheel
Incline
Lever
Incline
Leg
Rear Roller
Adjustment Bolts
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
.
1. With the help of a second person, carefully lay the
treadmill on its right side as shown (refer to the drawing
on page 4 to identify the right side).
1
83
Insert the Extension Legs (88) into the treadmill. Make
sure that the Extension Legs are turned so the Base
Pads (70) are on the indicated side. Attach each
Extension Leg with an Extension Leg Screw (83).
88
70
With the help of a second person, carefully raise the
treadmill to the upright position so the Extension Legs
(88) are resting flat on the floor.
88
70
83
2. Refer to HOW TO LOWER THE TREADMILL FOR USE
on page 11. Follow the instructions on page 11 to lower
the treadmill.
2
Bracket
56
Bracket
Insert the brackets on the Console Base (56) into the
Uprights (84); insert any slack in the Wire Harness (54)
into the right Upright. Thread four Handrail Bolts (48)
with Handrail Washers (47) into the Uprights. Tighten
all four Handrail Bolts.
89
54
47
47
48
48
89
Make sure that the two indicated Grommets (89) are
pressed into the holes.
84
3. Remove the two Frame Guide Screws (9) from the left
side of the Frame (5).
3
Attach the Frame Guide (10) and the Frame Guide
Spacer (11) to the Frame (5) with two Frame Guide
Screws (9) as shown. Note: Be careful not to over-
tighten the Screws. Make sure that the thick end of
the Frame Guide is at the bottom.
10
9
11
Thick End
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the backing from the Wrench Clip (26). Press
the Wrench Clip onto the base of the Uprights (84) in the
indicated location. Press the Allen Wrench (29) into the
Wrench Clip.
4
84
26
29
5. Make sure that all parts are tightened before you use the treadmill. To protect the floor or carpet, place
a mat under the treadmill.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
1
HOW TO PLUG IN THE POWER CORD
Grounded Outlet Box
Surge Suppressor
Grounding Pin
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet
Grounding Pin
Grounded Outlet
Grounding Plug
installed by a qualified electrician.
2
Grounded Outlet Box
Adapter
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).
Surge Suppressor
Lug
Metal Screw
Surge suppressors are sold at most hardware stores
and department stores. Use only a single-outlet surge
suppressor that is UL 1449 listed as a transient voltage
surge suppressor (TVSS). The surge suppressor must
have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE OPERATION
Reading Rack
Water Bottle Holder
Displays
Start/Pause Button
Speed Buttons
Accessory Tray
Key
Clip
Follow the steps below to operate the console.
CAUTION:Before operating the
console, read the following precautions.
Insert the key into the console.
1
¥ Do not stand on the walking belt when turn-
ing on the power or starting the walking belt.
When the key is inserted, the four displays will
turn on.
¥ Always wear the clip (see the drawing above)
while operating the treadmill. If the key is
pulled from the console, the walking belt will
stop.
Press the start/pause button.
2
A moment after the button is pressed, the walking
belt will begin to move at 1 mile per hour. Hold the
handrails and begin walking. Note: The walking
¥ The treadmill is capable of high speeds;
adjust the speed in small increments.
belt can also be started by pressing the speed
button once.
▲
¥ To reduce the risk of electric shock, keep the
console dry. Avoid spilling liquid on the
console and use only a sealable water bottle.
Adjust the speed of the walking belt with the
speed buttons.
3
As you walk on the tread-
mill, adjust the speed of
the walking belt with the
speed buttons. Each time
STEP BY STEP CONSOLE OPERATION
one of the buttons is
pressed, the speed will
If there is a thin sheet of clear plastic on the console,
remove it. In addition, make sure that the power cord is
properly plugged in (see HOW TO PLUG IN THE
POWER CORD on page 7).
change by 0.1 mile per hour. The buttons can be
held down to change the speed quickly. The
speed range is 0.5 to 10 miles per hour. Note:
After the buttons are pressed, it may take a
moment for the walking belt to reach the selected
speed setting.
Next, step onto the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothing.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the walking belt, press the start/pause
button. The displays will pause and the time dis-
play will begin to flash. To restart the walking belt,
press the start/pause button again. Note: The
walking belt can also be stopped by pulling the
key out of the console.
HOW TO CHANGE THE INCLINE OF THE
TREADMILL
The incline of the treadmill can be changed by raising
or lowering the back end. Before changing the in-
cline, remove the key and unplug the power cord.
Hold the rear
roller endcaps
as shown.
Follow your progress with the four displays.
4
Time displayÑThis
display shows the total
time that you have
walked or run on the
treadmill.
When the
back end of
the treadmill
is in the low-
est position,
Incline
Leg
Incline
Lever
the incline is
at the perfor-
mance level
(see the inset
drawing). To
change the
Speed displayÑThis
display shows the speed
of the walking belt, in
miles per hour.
incline, lift the
incline lever
with your left
Distance displayÑThis
display shows the total
distance that you have
walked or run, in miles.
hand, raise the back end of the treadmill slightly, and
release the incline lever. Continue to raise the back
end of the treadmill until the incline leg locks into posi-
tion; if necessary, shake the treadmill lightly until the
incline leg locks into position. The incline will then be at
the aerobic level. Repeat this procedure. The incline
will then be at the warm-up level. To change the incline
back to the performance level, lift the incline lever and
lower the back end of the treadmill. CAUTION: Before
exercising, push on the back of the treadmill to
make sure that the incline leg is locked in position.
Do not place objects under the treadmill to change
the incline; change the incline only as described
above.
Calories/Fat Calories
displayÑThis display
shows the approximate
numbers of calories and
fat calories you have
burned. Every seven
seconds, the display will
change from one number to the other. An ÒFÓ will
appear in the display when the number of fat calo-
ries is shown.
To reset the displays, remove the key from the
console and then reinsert it.
When you are finished exercising, remove the
key.
5
Step onto the foot rails and remove the key from
the console. Keep the key in a secure place.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Unplug the power cord. Caution: You must be able to
safely lift 45 pounds (20 kg) in order to raise, lower, or
move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. Caution: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Raise the treadmill until the storage latch
closes over the frame guide. Make sure that the storage
latch closes fully over the frame guide.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the storage
position in temperatures above 85¡ Fahrenheit.
Closed
Storage
Latch
Frame
Guide
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the stor-
age latch is closed fully over the frame guide.
1. Hold the upper ends of the treadmill. Place one foot on
the base as shown.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To
reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
Base
Front Wheels
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left thumb, slide open the storage latch
and hold it open. Pivot the treadmill until the frame is past
the storage latch.
Opened
Storage
Latch
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Caution: To decrease the possibil-
ity of injury, bend your legs and keep your back
straight.
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the simple steps below. If further assistance is
needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m.
Central Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor
that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor
must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of
450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
(See step 1 on page 8.)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
c
Tripped
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 8.)
d. If the treadmill still will not run, please call our toll-free HELPLINE.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the six screws from the hood. Carefully re-
move the hood. Locate the Reed Switch (16) and the
1/8Ó
Magnet (15) on the left side of the Pulley (20). Turn
the Pulley until the Magnet is aligned with the Reed
20
16
15
Switch. Make sure that the gap between the
Magnet and the Reed Switch is about 1/8Ó. If nec-
essary, loosen the Screw (18) and move the Reed
Switch slightly. Retighten the Screw. Re-attach the
hood, and run the treadmill for a few minutes to check
for a correct speed reading.
18
Top
View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically
rated for 120 volts AC and 15 amps.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be
b
3ÓÐ4Ó
permanently damaged. Remove the key and UN-
PLUG THE POWER CORD. Using the allen wrench,
turn both rear roller adjustment bolts counterclock-
wise, 1/4 of a turn. When the walking belt is properly
tightened, you should be able to lift each side of the
walking belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
Rear Roller Adjustment Bolts
power cord, insert the key and run the treadmill for a
few minutes. Repeat until the walking belt is properly
tightened.
c. If the walking belt still slows when walked on, please call our toll-free HELPLINE.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center when walked on
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn the left rear roller adjustment
bolt clockwise, and the right bolt counterclockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
a
b. If the walking belt has shifted to the right, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn the left rear roller adjustment
bolt counterclockwise, and the right bolt clockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
b
PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller adjustment
bolts clockwise, 1/4 of a turn. When the walking belt
is correctly tightened, you should be able to lift each
side of the walking belt 3 to 4 inches off the walking
platform. Be careful to keep the walking belt centered.
Plug in the power cord, insert the key and carefully
walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
a
PROBLEM: THE WALKING BELT NEEDS TO BE CLEANED
SOLUTION: a. Use a color-fast upholstery cleaner to clean the walking belt. Test the cleaner on a small area be-
fore cleaning the entire belt.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn fat,
adjust the speed and incline of the treadmill until your
heart rate is near the lowest number in your training
zone as you exercise.
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for in-
dividuals over the age of 35 or individuals
with pre-existing health problems.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system,
your exercise must be Òaerobic.Ó Aerobic exercise is
activity that requires large amounts of oxygen for pro-
longed periods of time. This increases the demand on
the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the middle number in your training
zone.
The following guidelines will help you to plan your
exercise program. RememberÑthese are general
guidelines only. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the de-
sired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, aerobic exercise,
and high performance athletic conditioning.
High Performance Athletic Conditioning
If your goal is high performance athletic conditioning,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone. Note: During the first few weeks of your exercise
program, keep your heart rate near the low end of your
training zone as you exercise.
Training Zone Chart
HOW TO MEASURE YOUR HEART RATE
Maximum
Minimum
To measure your
heart rate, stop
exercising and
place two fingers
on your wrist as
shown. Take a
Training
Zones
six-second heart-
beat count, and
multiply the result
by ten to find your
heart rate. (A six-second count is used because your
heart rate drops quickly when you stop exercising.) If
your heart rate is too high or too low, adjust the speed
or incline of the treadmill accordingly.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, look above your age and
find the box containing three numbers. The three num-
bers are your Òtraining zone.Ó The lowest number is the
recommended heart rate for fat burning; the middle
number is the recommended heart rate for aerobic ex-
ercise; the highest number is the recommended heart
rate for high performance athletic conditioning.
WORKOUT GUIDELINES
Each workout should include the following three impor-
tant parts:
A Warm-up
Fat Burning
Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Training Zone Exercise
muscles and will help to prevent post-exercise
problems.
After warming up, increase the intensity of your exer-
cise until your heart rate is in your training zone for 20
to 60 minutes. Note: During the first few weeks of your
exercise program, do not keep your heart rate in your
training zone for longer than 20 minutes.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
A Cool-down
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
SUGGESTED STRETCHES
The correct form for several basic stretches is described
below. Move slowly as you stretchÑnever bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward and
move your hips toward the wall. Hold for 15 counts, then relax.
Repeat 3 times for each leg. To cause further stretching of the
achilles tendons, bend your back leg as well. Stretches:
Calves, achilles tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold
for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. 831.297820
R0198A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
5
1
1
1
2
1
6
7
2
1
1
1
3
1
1
1
1
4
1
1
1
1
12
2
1
1
1
1
2
2
1
2
1
2
3
1
1
1
1
1
1
1
4
1
4
4
4
1
14
1
1
4
1
1
Rear Roller Adjustment Bolt
Roller Adjustment Washer
Left Rear Endcap
Latch Decal
Frame
Roller Guard
Nut Cap
Platform Screw
Frame Guide Screw
Frame Guide
Frame Guide Spacer
Left Foot Rail
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95*
96
97
98
#
1
1
1
1
1
43
1
1
1
1
1
1
2
1
4
7
1
1
1
1
1
1
1
4
2
3
2
2
1
2
2
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
Console Base
Console
Console Plug
Console Insert
Console Insert Plate
Screw
Hood
Key/Clip
Storage Latch Bracket
Power Cord Grommet
Power Cord
Circuit Breaker
Latch Spring
Front Belly Pan
Base Pad
Base Pad Screw
Electronics Bracket
Controller
Storage Latch
Choke
Power Supply
Right Handrail
Hood Cover Plug
Hood Anchor
Upright Base Endcap
Pivot Bolt
Frame Pivot Washer
Extension Leg Screw
Upright Base
Wheel Bolt
Wheel
Shock
Extension Leg
Grommet
Motor Tension Nut
Tension Star Washer
Motor Tension Washer
Motor Tension Bolt
Motor Pivot Bolt
Motor/Pulley/Flywheel/Fan
Motor
Incline Lever Washer
Reed Switch Bracket
8Ó White Wire, Male/Female
8Ó White Wire, 2 Female
6Ó White Wire, Male/2 Female
8Ó Blue Wire, 2 Female
8Ó Blue Wire, Male/2 Female
4Ó Blue Wire, 2 Female
8Ó Red Wire, Male/Female
4Ó Black Wire, 2 Female
8Ó Green Ground Wire
UserÕs Manual
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Walking Platform
Upright Spacer
Magnet
Reed Switch
Reed Switch Clip
Reed Switch Clip Screw
Upright Pivot Nut/Wheel Nut
Front Roller/Pulley
Front Roller Adjustment Bolt
Walking Belt
Right Foot Rail
Belly Pan Fastener
Belt Guide
Wrench Clip
Rear Roller
Belly Pan
Allen Wrench
Cable Tie Clamp
Cable Tie
Ground Wire
Ground Screw
Left Incline Leg Bolt
Incline Leg Cap
Incline Leg Nut
Right Endcap
Incline Leg Spacer
Incline Leg
Hat Cap
Incline Spring
Incline Lever
Lever Cover
Handrail Cap
Left Handrail
Cage Nut
Handrail Washer
Handrail Bolt
Motor Belt
Console Screw/Latch Screw
Console Plate
Hood Cover
#
#
#
#
#
#
#
#
8Ó Cable Tie
Wire Harness
Pulley/Flywheel/Fan
#
* Includes all parts shown in the box
# These parts are not illustrated
Download from Www.Somanuals.com. All Manuals Search And Download.
16
14
15
19
18
61
17
8
20
98
21
2
12
13
8
19
11
9
10
22
7
6
14
8
23
3
24
6
2
1
24
25
27
61
4
9
41
10
28
26
24
24
1
53
5
97
2
29
42
35
40
43
37
24
14
29
34
30
31
36
33
32
39
36
81
38
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
The model number and serial number of your HEALTHRIDER¨
SOFTSTRIDER LX treadmill are listed on a decal attached to the
treadmill. See the front cover of this manual to find the location of
the decal.
Model No. 831.297820
QUESTIONS?
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
If you find that:
¥ you need help assembling or
operating the HEALTHRIDER¨
SOFTSTRIDER LX
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
¥ a part is missing
¥ The NAME OF THE PRODUCT (HEALTHRIDER¨ SOFT-
STRIDER LX treadmill)
¥ you need to schedule repair
service
call our toll-free HELPLINE
¥ The MODEL NUMBER OF THE PRODUCT (831.297820)
1-800-736-6879
MondayÐSaturday, 7 amÐ7 pm
Central Time (excluding holidays)
¥ The PART NUMBER AND DESCRIPTION OF THE PART (see
the EXPLODED DRAWING and PART LIST included in this
manual)
REPLACEMENT
PARTS
If parts become worn and need
to be replaced, call the following
toll-free number
1-800-FON-PART
(1-800-366-7278)
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS TREADMILL EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the TREADMILL EXERCISER, free of charge.
This warranty does not apply when the TREADMILL EXERCISER is used commercially or for rental pur-
poses.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 143315 H00023-C R0198A
Printed in USA © 1998 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|