NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY PLATINUM
MP-PWR 10.0
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP-PWR10.0
Retain This
Manual for
Reference
04-08-05
OWNER'S
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended this machine be assembled by two or more people
to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Main Frame (#27) to the Bench Front & Rear Stabilizers (#28 & 29). Secure
each end with two M10 x ¾” Allen Bolts (#81) and ∅ ¾” Washers (#69).
B.) Attach four Stabilizer End Caps (#58) onto the Stabilizers.
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the two side-holes on bottom of Backrest Supports (#30) to the pivot on the Main
Frame (#27). Secure it with one M12 x 5 ¾” Allen Bolt (#75), two Ø 1” Washers (#68), and
one M12 Aircraft Nut (#71).
B.) Align the pivot on top of Backrest Incline Support (#31) to the middle side-holes in between
the Backrest Supports. Secure it with one M12 x 5 ¾” Allen Bolt (#75), two Ø 1” Washers
(#68), and one M12 Aircraft Nut (#71).
C.) Attach the Backrest Board (#36) onto the Backrest Supports and secure it with four M8 x 1
5/8” Allen Bolts (#83) and Ø 5/8” Washers (#70).
D.) Place the Seat Pad (#35) onto the Main Frame. Secure it with four M8 x 1 5/8” Allen Bolts
(#83) and Ø 5/8” Washers (#70).
DIAGRAM 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#33) to the open bracket on the Main Frame (#27). Secure it
with one M10 x 3 1/8” Allen Bolt (#76), two Ø ¾” Washers (#69), and one M10 Aircraft
Nut (#72). Do not over tighten the bolt and nut, make sure Leg Developer is able to
swivel.
B.) Insert the U-shaped Pin (#39) into the open tube on the Main Frame (#27). Secure it
with one M6 x ½” Philips Screw (#43), Ø ½” Washer (#41), and Spring (#42). Pull and
turn to lock the Leg Developer in position while using the bench at declined position.
C.) Insert three Foam Tubes (#38) halfway through the holes on the Main Frame and Leg
Developer. Push six Foam Rolls (#60) onto the Tubes from both ends. Plug six Foam
Roll End Caps (#56) into the ends.
D.) Slide an Olympic Sleeve (#44) onto the weight post on the Leg Developer.
E.) Attach the Curl Bar Holder (#34) to the Leg Developer and lock it with a L-shaped Pin
(#40).
DIAGRAM 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Arm Curl Pad (#37) to the Arm Curl Stand (#32). Secure it with two M8 x ¾”
Allen Bolts (#84) and two ∅ ¾” Washers (#70). Insert the Arm Curl Stand into the front
opening on the Main Frame (#27) and secure it with a Lock Knob (#61) to hold it at the
desired height.
B.) Remove the Arm Curl when using the Leg Developer to exercise.
DIAGRAM 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Note: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Attach the top of Left Support (#2) to an Upright Beam (#1). Secure it with two M10 x 5/8”
Allen Bolts (#82) and Ø ¾” Washers (#69).
C.) Attach the Left Floor Stabilizer (#4) to the Upright Beam. Secure it with one M10 x 4”
Carriage Bolt (#73), ∅ ¾” Washer (#69), and M10 Aircraft Nut (#72).
D.) Attach the other end of the Left Floor Stabilizer (#4) and Rear Stabilizer (#7) to the bottom
of Left Support (#2). Align the holes and secure them together with one M10 x 2½”
Carriage Bolt (#74), Ø ¾” Washer (#69), and M10 Aircraft Nut (#72) to the upper hole.
Secure the lower hole with one M10 x 2 ½” Allen Bolt (#77) and Ø ¾” Washer (#69).
E.) Repeat procedure B, C, and D above to install the other side.
F.) Connect the Left & Right Supports (#2 & 3) with the Cross Brace (#6). Secure each end
with two M10x2½” Carriage Bolts (#74), ؾ” Washers (#69), and M10 Aircraft Nuts (#72).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Attach the Rear Vertical Frame (#9) onto the Rear Base (#8). Secure it with two M10
x 2 ½” Carriage Bolts (#74), Ø ¾” Washers (#69), and M10 Aircraft Nuts (#72).
B.) Attach the Rear Base (#8) and Front Vertical Frame (#10) to the Rear Stabilizer (#7).
Align the holes and secure them together with two M10 x 2 ½” Carriage Bolts (#74),
Ø ¾” Washers (#69), and M10 Aircraft Nuts (#72).
C.) Align the Front Vertical Frame (#10) to the Cross Brace (#6). Secure it with one 4
3/8” x 1 ¾” Bracket (#22), two M10 x 2 ½” Carriage Bolts (#74), two Ø ¾” Washers
(#69), and two M10 Aircraft Nuts (#72).
D.) Slide the Sliding Weight Post (#12) onto the Rear Vertical Frame (#9) from the top.
E.) Attach the Upper Frame (#11) onto the Front Vertical Frame (#10). Secure it with two
M10 x 5/8” Allen Bolts (#82) and Ø ¾” Washers (#69).
F.) Attach the rear of Upper Frame (#11) to the Rear Vertical Frame (#9). Secure it with
one M10 x 2 ½” Allen Bolt (#77), Ø ¾” Washer (#69), and 3 1/8” x 1 ¾” Bracket (#21)
to the upper hole. Secure the lower hole with one M10 X 2 ½” Carriage Bolt (#74), Ø
¾” Washer (#69), and M10 Aircraft Nut (#72).
G.)Securely tighten all Nuts and Bolts previously installed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 113 7/8” Upper Cable (#24) to the front opening on the Upper Frame (#11). Make
sure the ball stopper of the Cable is underneath the Frame.
B.) Attach a Pulley (#45) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#77), two 5/8”
Pulley Bushings (#65), and one M10 Aircraft Nut (#72).
C.) Draw the Cable along the Upper Frame towards the back of the machine to the open bracket
on the Upper Frame. Install a Pulley to the bracket with one M10 x 1 ¾” Allen Bolt (#80), two Ø
¾” Washers (#69), and one M10 Aircraft Nut (#72).
D.) Draw the Cable around the Pulley and downward. Install a Pulley to the Floating Pulley
Bracket (#23). Let the Bracket hanging for now. Pull the Cable around the Pulley and up to
the opening on the top of the Rear Vertical Frame (#9). Attach a Pulley to the opening and
secure it with one M10 x 2 3/8” Allen Bolt (#78), two ½” Pulley Bushings (#66), and one M10
Aircraft Nut (#72).
E.) Draw the Cable down to the Sliding Weight Post (#12) and secure it with one M10 x ¾” Allen
Bolt (#81), two ∅ ¾” Washers (#69) and one M10 Aircraft Nut (#72). Connect the Lat Bar
(#19) to the Cable with two Hooks (#46) and one Long Chain (#47).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8 & Cable Loop Diagram)
A.) Attach the 58 1/8” Lower Cable (#25) to the lower opening on the bottom of Front Vertical
Frame (#10). Attach a Pulley (#45) to the opening and secure it with one M10 x 2 3/8”
Allen Bolt (#78), two ½” Pulley Bushings (#66), and one M10 Aircraft Nut (#72).
B.) Pull the Cable underneath the Pulley to the open bracket on the Rear Base (#8). Install a
Pulley to the bracket with one M10 x 1 ¾” Allen Bolt (#80), two Ø ¾” Washers (#69), and
one M10 Aircraft Nut (#72).
C.) Pull the Cable around the Pulley then up to the Floating Pulley Bracket (#23) previously
installed in Step-7. Attach a Short Chain (#48) to the Bracket and secure it with one M10
x 1 1/8” Allen Bolt (#79), two ؾ” Washers (#69), and one M10 Aircraft Nut (#72).
D.) Connect the Cable to the Short Chain with a Hook (#46). Adjust the length of the Short
Chain to adjust the tension of the Cable Loop System.
E.) Connect the Shiver Bar (#17) to the Lower Cable with two Hooks and one Long Chain
(#47).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Attach a Weight Post (#20) to the Right Support (#3). Secure it with a M10 x ¾” Allen Bolt
(#81) and Ø ¾” Washer (#69). Slide an Olympic Sleeve (#44) onto the Post. Repeat the
same procedure to install the other side.
B.) Insert the Left & Right Bar Catches (#15 & 16), Left & Right Safety Catches (#13 & 14)
into the selected holes on the Upright Beams (#1).
DIAGRAM 9
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
RACK EXPLODED DIAGRAM
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
3
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
3
1
1
1
1
1
5
6
5
2
1
9
2
1
2
Upright Beam
Left Support
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
1 ¾” Square End Cap
2” Square End Cap
Ø ½” Bushing
1” Square End Cap
Ø 1” End Cap
Foam Roll End Cap
2” x 1 ¾” Sleeve
Stabilizer End Cap
Ø 1 ½” Rubber Bumper
Foam Roll
5
2
2
2
1
6
3
4
1
6
1
1
1
4
2
4
2
3
Right Support
4
5
6
Left Floor Stabilizer
Right Floor Stabilizer
Cross Brace
7
8
Rear Stabilizer
Rear Base
9
Rear Vertical Frame
Front Vertical Frame
Upper Frame
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Lock Knob
Single Handle
Sliding Weight Post
Left Safety Catch
Right Safety Catch
Left Bar Catch
Right Bar Catch
Shiver Bar
Shiver Bar Handle
Lat Bar
Weight Post
3 1/8” x 1 ¾” Bracket
4 3/8” x 1 ¾” Bracket
Floating Pulley Bracket
Upper Cable (113 7/8”)
Lower Cable (58 1/8”)
Panel
Ø 1 ¾” Rubber Bumper
Handle Grip
5/8” Pulley Bushing
½” Pulley Bushing
Ø 1 ½” Washer
Ø 1” Washer
Ø ¾” Washer
Ø 5/8” Washer
M12 Aircraft Nut
4
42
10
2
24
2
13
2
1
4
2
1
3
7
6
8
2
2
12
M10 Aircraft Nut
M10 x 4” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M12 x 5 ¾” Allen Bolt
M10 x 3 1/8” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 1 1/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x ¾” Allen Bolt
M10 x 5/8” Allen Bolt
M8 x 1 5/8” Allen Bolt
M8 x ¾” Allen Bolt
M6 x 5/8” Philips Screw
3/8” Panel Screw
Main Frame
Bench Front Stabilizer
Bench Rear Stabilizer
Backrest Support
Backrest Incline Support
Arm Curl Stand
Leg Developer
Curl Bar Holder
Seat Pad
Backrest Board
Arm Curl Pad
Foam Tube
U-shaped Pin
L-shaped Pin
Ø ½” Washer
Spring
M6 x ½” Philips Screw
Olympic Sleeve
Pulley
Hook
Long Chain
Short Chain
Ø 1” Con-shaped End Cap
1 5/8” x 3 1/8” End Cap
19
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use
and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends
only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at
IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight
damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service
center or for products used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with
the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of
revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or
whatsoever natures. Some states do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may
not apply to you.
This warranty gives you specific legal right.
You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899 during
our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|