MP770 Digital Projector
Mainstream Series
User's Manual
Welcome
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Table of contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
Your BenQ projector is designed and tested to meet the latest standards for safety of
information technology equipment. However, to ensure safe use of this product, it is
important that you follow the instructions mentioned in this manual and marked on the
product.
Safety Instructions
1.
Please read this manual before you
operate your projector. Save it for
future reference.
4.
Always open the lens shutter or
remove the lens cap when the
projector lamp is on.
5.
In some countries, the line voltage is
NOT stable. This projector is designed
to operate safely within a mains
2.
Do not look straight at the projector
lens during operation. The intense
light beam may damage your eyes.
voltage between 100 to 240 volts AC,
but could fail if power cuts or surges
of 10 volts occur. In areas where the
mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a
power stabilizer, surge protector or
uninterruptible power supply (UPS).
3.
Refer servicing to qualified service
personnel.
6.
Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire. To
temporarily turn off the lamp, press
BLANK on the projector or remote
control.
Important safety instructions
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
7.
The lamp becomes extremely hot
during operation. Allow the
projector to cool for approximately
45 minutes prior to removing the
lamp assembly for replacement.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
11. Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. The only
user serviceable part is the lamp
which has its own removable cover.
Under no circumstances should you
ever undo or remove any other
covers. Refer servicing only to
suitably qualified professional
service personnel.
8.
Do not operate lamps beyond the
rated lamp life. Excessive operation
of lamps beyond the rated life could
cause them to break on rare
occasions.
9.
Never replace the lamp assembly or
any electronic components unless
the projector is unplugged.
6
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
12. Do not place this projector in any of the 13. Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth or
any other item.
following environments.
- Space that is poorly ventilated or confined.
Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Do not place inflammables near the
projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled up.
- Locations where excessive humidity, dust,
or cigarette smoke may contaminate
optical components, shortening the
projector's life span and darkening the
image.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
14. Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of, or
damage to, the lamp.
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 10000 feet.
15. Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
10000
feet
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Safety Instructions (Continued)
16. Do not step on the projector or place 18. This product is capable of displaying
any objects upon it. Besides probable
physical damage to the projector, doing
so may result in accidents and possible
injury.
inverted images for ceiling mount
installation.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it is
securely installed.
17. Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet, disconnect
it from the power supply's wall socket
and call BenQ to have the projector
serviced.
19. When the projector is under operation,
you may sense some heated air and
odor from its ventilation grill. It is a
normal phenomenon and not a
product defect.
8
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
•
Selectable password protected function
Off and Go function allowing presenters to unplug the projector right after the
projector is turned off
•
•
Up to 11 sets of application modes providing multiple choices for different projection
purposes
Optional wireless module allowing more computers to share one projector through
cable or wireless connection
•
•
•
•
•
•
•
•
•
•
•
•
High quality manual zoom lens
One-key auto-adjustment to display the best picture quality
Two-way digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
Ultra-high brightness projection lamp
Ability to display 16.7 million colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and Economic modes to reduce the power consumption
Built-in speaker provides mixed mono audio when an audio input is connected
Powerful AV function to provide high quality video image
Component HDTV compatibility (YPbPr)
Replaceable dust filter
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input source contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Shipping contents
The projector is shipped with the cables required for connection to a PC or video
equipment. Carefully unpack and verify that you have all of the items shown below. If any of
these items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Projector
Soft carry case
User's manual
Remote control with batteries
Quick start
guide
User's manual
CD
Replacement filter
VGA cable
USB cable
Power cord
PC audio cable
Component Video to VGA (D-Sub)
adaptor cable
Optional accessories
1.
2.
3.
Macintosh adapter
Spare lamp kit
Ceiling mount kit
4.
5.
RS232 connector
Wireless module
10
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector exterior view
Front/upper side
1.
External control panel
details.)
Vent (heated air exhaust)
Projection lens
Quick-release button
Lens cap
Focus ring and Zoom ring
Front IR remote sensor
1
6
7
2.
3.
4.
5.
6.
7.
2
3
4
5
Rear side
11 12 13
14
15
16
17 18 19 20
10
9
8
21
8.
9.
Rear adjuster foot
AC power cord inlet
15. RGB (PC)/Component video (YPbPr/
YCbCr) signal input socket
16. DVI-I signal input socket
17. Video input socket
18. S-Video input socket
19. Audio input socket
10. Filter case
11. Rear IR remote sensor
12. USB socket
13. RS232 control port
14. RGB signal output socket
20. Audio output socket
21. Speaker grill
Lower/side view
22
25
23
22. Quick-release foot
23. Lamp cover
24. Rear adjuster foot
25. Kensington anti-theft lock slot
24
Introduction
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and functions
Projector
1
2
10
11
3
6
12
6
13
6
4
5
6
7
8
9
1.
2.
3.
4.
Focus ring
I
5.
Power
Adjusts the focus of the projected image.
clarity" on page 35 for details.
Zoom ring
Toggles the projector between standby
mode and on.
When the projector is in standby mode,
press once to turn the projector on.
When the projector is on, press twice to
turn the projector to standby.
details.
Adjusts the size of the image. See "Fine-
35 for details.
Power indicator light
Lights up or flashes when the projector is
under operation. See "Indicators" on page
60 for details.
6.
Keystone/Arrow buttons (
Left, Down,
/
Up,
/
/
/
Right)
MENU/BACK
Turns on the On-Screen Display (OSD)
menu.
Manually corrects distorted images
resulting from an angled projection.
When the On-Screen Display (OSD)
menu is activated, the buttons are used as
directional arrows to select the desired
menu items and to make adjustments.
"Using the menus" on page 46 for details.
Goes back to previous OSD menu, exits
and saves menu settings.
details.
12
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
MODE
11. Lamp indicator light
Depending upon which input signal is
selected, selects an available picture
setup mode. See "Application Mode"
on page 48 for details.
Indicates the status of the lamp. Lights
up or flashes when the lamp has
developed a problem. See "Indicators"
on page 60 for details.
12. AUTO
When a wireless module is installed
and the Wireless Connection menu is
displayed, press this button to change
among LAN, IEEE 802.11 a, and IEEE
802.11 b/g. (The wireless module is
available through BenQ retailers.)
BLANK
Automatically determines the best
picture timings for the displayed
image. See "Auto-adjusting the image"
on page 35 for details.
When a wireless module is installed,
the Wireless Connection menu is
displayed and the IEEE 802.11 a is
selected, press this button to search for
a reliable channel. (The wireless
module is available through BenQ
retailers.)
8.
9.
Used to hide the screen image. To
restore the image, press any button
(except LASER) on the projector or
remote control. See "Hiding the image"
on page 40 for details.
ENTER
13. SOURCE
Enacts the selected On-Screen Display
(OSD) menu item. See "Using the
menus" on page 46 for details.
Sequentially selects the input signal D-
Sub (Analog RGB), Comp. (YPbPr),
DVI-A, DVI-D, Video, or S-Video. See
details.
10. Temperature warning light
Lights up red if the projector's
temperature becomes too high. See
"Indicators" on page 60 for details.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Remote control
2.
3.
ASPECT
12
13
Selects the display aspect ratio. See
details.
1
2
14
15
WIRELESS
Turns on or off the wireless connection
menu. See "Wireless connection
(optional)" on page 22 for details.
3
4
4.
Keystone/ Arrow buttons (
Left, Down,
/
Up,
/
16
4
5
4
6
/
/
Right)
Manually corrects distorted images
resulting from an angled projection.
When the On-Screen Display (OSD)
17
menu is activated, the buttons are used as
directional arrows to select the desired
menu items and to make adjustments.
"Using the menus" on page 46 for details.
MENU/BACK
4
7
18
8
9
5.
6.
Turns on the On-Screen Display (OSD)
menu.
19
20
10
11
Goes back to previous OSD menu, exits
and saves menu settings.
details.
BLANK
Used to hide the screen image. To restore
the image, press any button (except
LASER) on the projector or remote
control. See "Hiding the image" on page
40 for details.
I
1.
Power
7.
8.
ENTER
Toggles the projector between standby
mode and on.
Enacts the selected On-Screen Display
(OSD) menu item. See "Using the menus"
on page 46 for details.
When the projector is in standby mode,
press once to turn the projector on.
When the projector is on, press twice to
turn the projector to standby.
details.
CONTRAST
Displays the Contrast adjustment bar. To
adjust the value, press the directional
arrow buttons on the projector or remote
control.
14
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
BRIGHTNESS
16. AUTO
Automatically determines the best picture
Displays the Brightness adjustment bar. To
adjust the value, press the directional
arrow buttons on the projector or remote
control.
timings for the displayed image. See
details.
10. CAPTURE
Captures the projected image and save it
as your startup screen. See "Creating your
own startup screen" on page 42 for details.
11. PIP
When a wireless module is installed, the
Wireless Connection menu is displayed
and the IEEE 802.11 a is selected, press
this button to search for a reliable channel.
(The wireless module is available through
BenQ retailers.)
Turns the Picture In Picture (PIP) window
on or off. See "PIP (Picture In Picture)
operation" on page 41 for details.
12. LED indicator light
17. SOURCE
Sequentially selects the input signal D-Sub
(Analog RGB), Comp. (YPbPr), DVI-A,
DVI-D, Video, or S-Video. See "Switching
input signal" on page 34 for details.
Lights red when any button on the remote
control is pressed.
18. LASER
13. MODE
Emits visible laser pointer light for
presentation purposes.
Depending upon which input signal is
selected, selects an available picture setup
mode. See "Application Mode" on page 48
for details.
The Laser Pointer is a presentation aid for
professionals. It emits red colored light
when you press it and the LED indicator
lights up red.
When a wireless module is installed and
the Wireless Connection menu is
displayed, press this button to change
among LAN, IEEE 802.11 a, and IEEE
802.11 b/g. (The wireless module is
available through BenQ retailers.)
14. FREEZE
WARNING: Do not look into the laser light
window or shine the laser light beam on
yourself or others. See the warning
messages on the back of the remote
control and the attached ''User
Information'' prior to using it.
The image is frozen when FREEZE is
pressed. To release the function, press any
button (except LASER) on the projector
or remote control. See "Freezing the
image" on page 42 for details.
15. MUTE
19. DIGITAL ZOOM buttons (+, -)
Magnifies or reduces the projected image
size.
20. PAGE UP and PAGE DOWN
Operate your display software program
(on a connected PC) which responds to
page up/down commands (like Microsoft
PowerPoint). See "Remote paging
operations" on page 42 for details.
Toggles projector audio between on and
off.
Warning messages on the back of the remote control
The laser beam is visible. It is necessary to press and hold LASER for
continuous output.
The laser pointer is not a toy. Parents should be mindful of the dangers of
laser energy and keep this remote control out of the reach of children.
Refer to the warning labels on the back of your remote control for safe operation on the laser
pointer.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 6 meters (~ 20 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
•
Operating the projector from the
rear
•
Operating the projector from the
front
Remote control batteries
1.
2.
3.
To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it up in the direction of the arrow as illustrated. The
cover will slide off.
Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and sliding it back down into position. Stop
when it clicks into place.
1
3
2
•
Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
•
•
Replace only with the same or equivalent type recommended by the battery manufacturer.
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
•
•
Never throw the batteries into a fire. There may be danger of an explosion.
If the batteries are dead or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
16
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
1.
2.
3.
4.
Table in front of screen;
Ceiling in front of screen;
Table at rear of screen;
Ceiling at rear of screen.
1.
Front Table
Select this location with the projector placed near the
floor in front of the screen. This is the most common
way to position the projector for quick setup and
portability.
2.
Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the BenQ Projector Ceiling Mounting Kit
from your dealer to mount your projector on the
ceiling.
Set Front Ceiling in the System Setup: Basic >
Projector Position menu after you turn the projector on.
3.
Rear Table
Select this location with the projector placed near the
floor behind the screen.
Note that a special rear projection screen is required.
Set Rear Table in the System Setup: Basic > Projector
Position menu after you turn the projector on.
4.
Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
BenQ Projector Ceiling Mounting Kit are required for
this installation location.
Set Rear Ceiling in the System Setup: Basic >
Projector Position menu after you turn the projector on.
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
17
If you use the projector with wireless function, there's no need to worry about data cable
connections.This gives you the flexibility to site the projector anywhere in the room up to a
range of 20m away from your notebook, and switch between presentations on different
notebooks instantly without fiddling with cables
To use the wireless function, you need to install a BenQ wireless module to the projector and
enable your notebook/desktop PC with wireless connection. For more information, refer to
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your BenQ projector, so we need to bring
this safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a BenQ projector ceiling mount kit from the place you purchased your
BenQ projector. BenQ recommends that you also purchase a separate Kensington lock
compatible security cable and attach it securely to both the Kensington lock slot on the
projector and the base of the ceiling mount bracket. This will perform the secondary role of
restraining the projector should its attachment to the mounting bracket become loose.
18
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting, and the video format
each factors in the projected image size.
The maximum (native) resolution of the projector is 1024 x 768 pixels, which is a 4 to 3
aspect ratio (expressed as 4:3). To be able to project a complete 16:9 (widescreen) aspect
ratio image, the projector can resize and scale a widescreen image to the projector's native
aspect width. This will result in a proportionally smaller height equivalent to 75% of the
projector's native aspect height.
16:9 aspect image scaled to a 4:3 aspect
4:3 aspect image in a 4:3 aspect display area
display area
Thus, a 16:9 aspect image will not utilize 25% of the height of a 4:3 aspect image displayed
by this projector. This will be seen as darkened (unlit) bars along the top and bottom
(vertical 12.5% height respectively) of the 4:3 projection display area whenever displaying a
scaled 16:9 aspect image in the vertical center of the 4:3 projection display area.
When determining the position of your projector, you should consider its intended use and
input signal aspect ratios. All inputs (other than composite Video being fed a 16:9 aspect
signal) will display in a 4:3 aspect ratio (and will require an additional 33% display height
than that of the scaled 16:9 aspect image projection area).
IMPORTANT: Do not select a permanent projector position based upon a 16:9 projection if you
will ever need to select an input (other than composite Video being fed a 16:9 aspect signal).
The projector should always be placed horizontally level (like flat on a table), and positioned
directly perpendicular (90° right-angle square) to the horizontal center of the screen. This
prevents image distortion caused by angled projections (or projecting onto angled surfaces).
The modern digital projector does not project directly forward (like older style reel-to-reel
film projectors did). Instead, digital projectors are designed to project at a slightly upward
angle above the horizontal plane of the projector. This is so that they can be readily placed
on a table and will project forward and upwards onto a screen positioned so that the bottom
edge of the screen is above the level of the table (and everyone in the room can see the
screen).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects
at a slightly downward angle.
of the projected image to be vertically offset from the horizontal plane of the projector.
When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are directly
proportional to the projection distance.
BenQ has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the
ideal location for your projector. There are two dimensions to consider, the perpendicular
horizontal distance from the center of the screen (projection distance), and the vertical
offset height of the projector from the horizontal edge of the screen (offset).
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
19
How to determine the position of the projector for a given
screen size
1.
2.
Select your screen size.
Refer to the table and find the closest match to your screen size in the left columns
labelled '4:3 Screen Diagonal'. Using this value, look across this row to the right to find
the corresponding average distance from screen value in the column labelled 'Average'.
This is the projection distance.
3.
4.
On that same row, look across to the right column and make note of the vertical Offset
value. This will determine the final vertical offset placement of the projector in
relation to the edge of the screen.
The recommended position for the projector is aligned perpendicular to the
horizontal center of the screen, at the distance from the screen determined in step 2
above, and offset by the value determined in step 3 above.
For example, if you are using a 120 inch screen, the average projection distance is 4432 mm
and with a vertical offset of 302 mm.
If you place the projector in a different position (to that recommended), you will have to tilt
it down or up to center the image on the screen. In these situations, some image distortion
will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on
page 35 for details.
How to determine the recommended screen size for a
given distance
This method can be used for situations where you have purchased this projector and would
like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1.
Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
2.
Refer to the table and find the closest match to your measurement in the average
distance from screen column labelled 'Average'. Check that your measured distance is
between the min and max distances listed on either side of the average distance value.
Using this value, look across that row to the left to find the corresponding screen
diagonal listed in that row. That is the projected image size of the projector at that
projection distance.
On that same row, look across to the right column and make note of the vertical Offset
value. This will determine the final placement of the screen in relation to the
horizontal plane of the projector.
3.
4.
For example, if your measured projection distance was 4.8m (4800mm), the closest match in
the Average column is 5089 mm. Looking across this row shows that a 3500 mm (3.5 m)
screen is required. If you can only obtain imperial sized screens, the listed screen sizes on
either side of the 3.5 m screen are the 10' and 12' screens.
Checking the min and max projection distance values for these screen sizes, indicates that
the 4.8 m measured projection distance will need to be reduced to fit the 10' size screen, or
increased to fit the 12' size screen. The projector can be adjusted (using the zoom control) to
display on these different screen sizes at those projection distances. Be aware that these
different screens have different vertical offset values.
20
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection dimensions
calculating the appropriate position.
Maximum zoom
Minimum zoom
Screen
Center of lens
Offset
Projection distance
4:3 Screen Diagonal
Distance from Screen in mm
Vertical Offset in mm
Feet Inches
mm
Min length
Average
Max length
(with max.
zoom)
1652
(with min.
zoom)
1893
2329
2367
2840
3106
3313
3787
3882
4260
4659
4733
5435
5680
6212
7100
7765
8520
9317
11833
4
48
1219
1500
1524
1829
2000
2134
2438
2500
2743
3000
3048
3500
3658
4000
4572
5000
5486
6000
7620
1773
2181
2216
2659
2908
3102
3546
3635
3989
4362
4432
5089
5318
5816
6648
7270
7978
8725
11080
121
149
151
181
198
211
241
248
272
297
302
347
362
396
453
495
543
594
754
2033
2065
2479
2710
2892
3305
3389
3718
4066
4131
4743
4957
5421
6196
6776
7436
5
6
60
72
7
8
84
96
9
108
120
144
180
216
300
10
12
15
18
25
8132
10327
There is 3% tolerance among these numbers due to optical component variations. BenQ
recommends that if you intend to permanently install the projector, you should physically test
the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 10). They are commercially available from electronics stores.
Wireless connection (optional)
The Wireless module allows for simultaneous wireless connectivity to multiple computers
which are wireless enabled. This saves you from having to swap data cables between the
projector and different computers during a presentation. Wireless connectivity is most
suitable for situations where multiple presenters with separate notebooks are required to
seamlessly present individual presentations, like in meetings, conferences, lectures and,
classrooms.
The Wireless module connects and attaches to the rear of the projector through the DVI-I
socket.
While the Wireless module is attached to the projector, you cannot use the DVI-I socket for DVI
cable connections.
Even though the projector may be using a wireless data connection, it still requires physical
connection to a power outlet using its power cable.
You can purchase a BenQ wireless module from
BenQ retailers. You should attach the wireless
module to the projector before you connect any
other cables. Refer to the user's manual
enclosed with the wireless module for
connection and operation details.
Projector with the wireless module
Cable connection
Connecting a computer or monitor
Connecting a computer
The projector provides a VGA and DVI input sockets that allow you to connect it to both
IBM® compatibles and Macintosh® computers. A Mac adapter (an optional accessory) is
needed if you are connecting legacy version Macintosh computers.
Additionally, you can also connect the projector to a computer via the USB cable so you can
perform paging operations of the application on the PC or notebook. (see "Remote paging
22
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
To connect the projector to a notebook or desktop computer (either through a
VGA cable or VGA to DVI-A cable):
•
With a VGA cable:
•
With a VGA to DVI-A cable:
1.
Take the supplied VGA cable and
connect one end to the D-Sub
output socket of the computer.
Connect the other end of the VGA
cable to the D-SUB/COMP. IN
signal input socket on the projector.
1.
Take a VGA to DVI-A cable and
connect the VGA end to the D-Sub
output socket of the computer.
Connect the DVI end of the VGA to
DVI-A cable to the DVI-I signal
input socket on the projector.
2.
2.
3.
4.
If you wish to use the remote paging function (see "Remote paging operations" on
page 42), take the supplied USB cable and connect the larger end to the USB port
of the computer, and the smaller end to the USB socket on the projector.
If you wish to make use of the projector (mixed mono) speaker in your
presentations, take a suitable audio cable and connect one end of the cable to the
audio output socket of the computer, and the other end to the AUDIO IN socket of
the projector.
5.
If you wish, you can use another suitable audio cable and connect one end of the
cable to the AUDIO OUT socket of the projector, and the other end to your
external speakers (not supplied).
The audio output is a mixed mono signal. Once connected, the audio can be
controlled by the remote control (MUTE) or projector On-Screen Display (OSD)
The final connection path should be like that shown in the following diagram:
notebook or desktop computer
Speakers
Audio cable
VGA
cable
or
VGA to
DVI-A
cable
Audio cable
USB cable
•
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate
a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook.
Press FN and the labeled function key simultaneously. Refer to your notebook's
documentation to find your notebook's key combination.
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the D-SUB OUT signal output socket on the projector to an external monitor
with a VGA or VGA to DVI-A cable by following the instructions below.
To connect the projector to a monitor (either through a VGA cable or VGA to
DVI-A cable):
•
With a VGA cable:
•
With a VGA to DVI-A cable:
Note: Your monitor must be equipped with
a DVI input socket.
1.
Connect the projector to a computer as described in "Connecting a computer" on
The D-SUB output only works when an appropriate D-SUB input is made to the
projector. Be sure the projector is connecting with the computer using the D-SUB
IN socket, not the DVI-I socket.
2.
3.
Take a suitable VGA cable (only one
supplied) and connect one end of
the cable to the D-Sub input socket
of the video monitor.
Connect the other end of the cable
to the D-SUB OUT socket on the
projector.
2.
Take a VGA to DVI-A cable and
connect the DVI end of the cable to
the DVI input socket of the video
monitor.
Connect the VGA end of the cable to
the D-SUB OUT socket on the
projector.
3.
The final connection path should be like that shown in the following diagram:
notebook or desktop computer
(DVI)
VGA to DVI-A cable
or VGA cable
VGA cable
(VGA)
24
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Video source devices
This section describes how to connect the projector to Video source devices using video
cables. Video cable connections are recommended for Video presentations.
This projector also supports data (graphic) "PC" connection using wireless function. Wireless
connection is not recommended for Video presentations. See "Wireless connection
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
•
•
•
•
DVI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is DVI. If your source device is equipped with a
DVI socket, based on the type of DVI connector you have, you can enjoy digital or high-end
analog video quality.
source device and other details.
If no DVI source is available, the next best video signal is Component Video (not to be
confused with composite Video). Digital TV tuners and DVD players output Component
Video natively, so if available on your devices, they should be your connection method of
choice in preference to S-Video or (composite) Video.
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
projector to a composite Video device.
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Connecting Audio
The projector has a built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theatre or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a mixed mono signal and controlled by the projector Volume and Mute
settings.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
The audio connections illustrated in the following sections are provided for informational
purposes only. You need not connect audio to the projector if there is an alternate sound
system available, or if audio is not required.
Connecting a DVI source device
The projector provides a DVI-I input socket that allows you to connect it to a DVI source
device like a DVD player, or a VGA output device like a notebook or desktop computer.
There are three types of DVI connectors: DVI-A, DVI-D, and DVI-I. The DVI-I socket is an
integrated connector which supports both formats: DVI-A, and DVI-D.
DVI-A format is used to carry a DVI signal to an analog (VGA) display, or vice-versa.
Although some signal quality is lost from the signal conversion, it still transmits higher
picture quality than a standard VGA connection.
DVI-D format is used to directly carry a digital signal to a digital display without signal
conversion. The pure digital connection provides faster and higher image quality than an
analog connection, due to the nature of the digital format.
DVI-A and DVI-D formats are non-interchangeable. You cannot connect a DVI-A format
connector to DVI-D equipment and visa-versa. Make sure you know which kind of format
your equipment is fitted with before you purchase any cables. Or you can purchase a DVI-I
cable which will be more useful in any type of DVI connection situation.
Examine your source device to determine if it has an unused DVI or VGA (D-Sub) output
socket available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
26
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
To connect the projector to a DVI source device or a computer:
For information on connecting a DVI source device to a computer through a VGA to DVI-A
1.
Take the DVI (DVI-D or DVI-I) cable and connect one end to the DVI output socket
of the DVI source device.
2.
3.
Connect the other end of the cable to the DVI-I signal input socket on the projector.
If you wish to make use the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output sockets of the video device,
and the other end to the AUDIO IN socket of the projector.
4.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the AUDIO OUT socket of the projector, and the other end to your external
speakers (not supplied).
The audio output is a mixed mono signal. Once connected, the audio can be
controlled by the remote control (MUTE) or projector On-Screen Display (OSD)
AV device
Audio
cable
Audio
cable
DVI-D or
DVI-I cable
This model does not support HDCP. When connected to an HDCP-compliant digital device
(like a DVD player) via the DVI input, the image may not display, or a non-compliance
message may be displayed instead. In cases like this, you will need to use an analog input
instead (like Component Video, S-Video, or composite Video) to view the image.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device through a
Component Video to VGA (D-Sub) adaptor cable:
1.
Take the Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the Video source
device. Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
27
2.
3.
Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with
a D-Sub type connector) to the D-SUB/COMP. IN socket on the projector.
If you wish to make use the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output sockets of the video device,
an the other end to the AUDIO IN socket of the projector.
4.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the Audio OUT socket of the projector, and the other end to your external speakers
(not supplied).
The audio output is a mixed mono signal. Once connected, the audio can be
controlled by the remote control (MUTE) or projector On-Screen Display (OSD)
The final connection path should be like that shown in the following diagram:
AV device
Speakers
Audio
cable
Audio
cable
Component Video
to VGA (D-Sub)
adaptor cable
If you connect the projector to a Digital TV (DTV) tuner, the following standards are
supported:
•
•
•
480i
576i
720p (50/ 60 Hz)
•
•
•
480p
576p
1080i (50/ 60 Hz)
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
•
•
Component Video is the only video input that delivers native 16:9 aspect ratio picture.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
28
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
Take a S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2.
3.
Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
If you wish to make use the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output sockets of the video device,
an the other end to the AUDIO IN socket of the projector.
4.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the Audio OUT socket of the projector, and the other end to your external speakers
(not supplied).
The audio output is a mixed mono signal. Once connected, the audio can be
controlled by the remote control (MUTE) or projector On-Screen Display (OSD)
The final connection path should be like that shown in the following diagram:
AV device
S-Video cable
Audio
cables
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an composite Video source device:
1.
Take the Video cable and connect one end to the composite Video output socket of the
Video source device.
2.
3.
Connect the other end of the Video cable to the VIDEO socket on the projector.
If you wish to make use the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output sockets of the video device,
an the other end to the AUDIO IN socket of the projector.
4.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the Audio OUT socket of the projector, and the other end to your external speakers
(not supplied).
The audio output is a mixed mono signal. Once connected, the audio can be
controlled by the remote control (MUTE) or projector On-Screen Display (OSD)
The final connection path should be like that shown in the following diagram:
AV device
Video cable
Audio cables
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 25 for details.
30
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Start up
1.
2.
3.
Plug the power cord into the projector and into
a wall socket. Turn on the wall socket switch
(where fitted). Check that the Power indicator
on the projector lights orange after power has
been applied.
Remove the lens cap. If it is left on, it could
become deformed due to the heat produced by the
projection lamp.
I
Press and hold (for 2 seconds)
Power on
the projector or remote control to start the
projector. The Power indicator light flashes
green and stays green when the projector is on.
The start up procedure takes about 30 seconds
I
after pressing
Power. In the later stage of
start up, a default BenQ logo is projected.
(If necessary) Rotate the focus ring to adjust
the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
4.
If you are prompted for a password, press the arrow buttons to enter a six digit
Switch all of the connected equipment on.
The projector will start to search for input signals. The current input source being
scanned displays in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the searching message will continue displaying until an input source
signal is found.
5.
6.
You can also press SOURCE on the projector or remote control to select your desired
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the On-Screen
Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the
WARNING: You will be inconvenienced if you activate the password functionality and
subsequently forget the password. Print out this manual (if necessary) and write the password
you used in this manual, and keep the manual in a safe place for later recall.
Setting a password
Once a password has been set, the projector cannot be used unless the correct password is
entered every time the projector is started.
1.
Open the OSD menu and go to SYSTEM SETUP: Advanced > Security Settings. Press
ENTER. Highlight Password and select On by pressing Left or
A prompt will display on the screen.
Right.
2.
3.
As pictured to the right, the four arrow buttons
INPUT PASSWORD
(
Up,
Right, Down,
Left) respectively
represent 4 digits (1, 2, 3, 4). According to the
password you desire to set, press the arrow
buttons to enter six digits for the password.
Once the password is set, the OSD menu returns
to the Security Settings page.
Back
IMPORTANT: The digits being input will display as
asterisks on-screen. Write your selected password down here in this manual in advance
or right after the password is entered so that it is available to you should you ever forget
it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
4.
To leave the OSD menu, press MENU/BACK twice.
If you forget the password
If the password function is activated, you will be asked
to enter the six digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right displays
lasting for three seconds, and the INPUT PASSWORD
message follows. You can retry by entering another six-
digit password, or if you did not record the password in
Password Error
Please try again.
this manual, and you absolutely do not remember it, you can use the password recall
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
32
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering the password recall procedure
Press and hold AUTO on the projector or remote
RECALL PASSWORD
control for 3 seconds. The projector will display a
coded number on the screen. Write down the number
and turn off your projector. Seek help from the local
BenQ service center to decode the number. You may
be required to provide proof of purchase
Please write down the recall code,
and contact your local BenQ
Customer Center.
Recall code:
0 2 1 2
documentation to verify that you are an authorized
user of the projector.
Exit
Changing the password
1.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings >
Change Password menu.
2.
3.
Press ENTER. the message 'INPUT CURRENT PASSWORD' displays.
Enter the old password.
i. If the password is correct, another message 'INPUT NEW PASSWORD' displays.
ii. If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT CURRENT PASSWORD' displays for your
retry. You can either press MENU/BACK to cancel the change or try another
password.
3.
Enter a new password.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your
selected password down here in this manual in advance or right after the password
is entered so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
4.
5.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to
the projector. Remember to enter the new
Password Changed
password next time the projector is started.
6.
To leave the OSD menu, press MENU/BACK
twice.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Password menu after opening the OSD menu system. Select Off by pressing
Left or Right. The message 'INPUT PASSWORD' displays. Enter the current
password.
i. If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Password. You will not have to enter the password
next time when turning on the projector.
ii. If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT PASSWORD' displays for your retry. You can
either press MENU/BACK to cancel the change or try another password.
Note that though the password function is disabled, you need to keep the old password in
hand should you ever need to re-activate the password function by entering the old
password.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Switching input signal
The projector can be connected to multiple devices
at the same time. However, it can only display one
full screen at a time. To cycle through the available
input sources, press SOURCE on the projector or
remote control. A source selection bar displays. You
can manually press SOURCE repeatedly until your
desired signal is selected or let the projector
automatically search for the available signal. Once
detected, the selected source information will
display at the upper left corner of the screen for 3
seconds. If there is multiple equipment connected to
the projector, you can press the button again to search for another signal.
Be sure the Auto Source Detection function in the SOURCE menu is activated if you want
details.
The projector features PIP function which allows 2 different signals to be displayed at the
The brightness level of the projected image will change accordingly when you switch
between different input signals. Data (graphic) "PC" presentations using mostly static
images are generally brighter than "Video" using mostly moving images (movies).
The input signal type effects the options available for the Application Mode. See "Selecting
an application mode" on page 38 for details.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and
lift the front of the projector. Once
the image is positioned where you
want it, release the quick-release
button to lock the foot in position.
Do not look into the lens while the lamp is
on. The strong light from the lamp may
cause damage to your eyes.
Be careful when you press the adjuster
button as it is close to the exhaust vent
where hot air comes from.
2.
Screw the rear adjuster foot to fine tune the horizontal angle.
To retract the foot, hold up the projector while pressing the quick-release button, then
slowly lower the projector. Screw the rear adjuster foot in a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
situation, adjust the value of Keystone in the DISPLAY menu, on the projector control panel,
34
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto-adjusting the image
In some cases, you may need to optimize the picture
quality. To do this, press AUTO on the projector or
remote control. Within 3 seconds, the built-in
Intelligent Auto Adjustment function will re-adjust
the values of Frequency and Clock to provide the
best picture quality.
The current source information will be displayed in
the upper left corner of the screen for 3 seconds.
The screen will be blank while AUTO is functioning.
Fine-tuning the image size and clarity
1.
Adjust the projected image to the size 2.
that you need using the zoom ring.
Then sharpen the image by rotating
the focus ring.
Searching for details on the projected image
If you need to find the details on the projected image, press D. ZOOM
+ on the remote control, the center of the image will be magnified.
When the + button is pressed again, the image is further magnified. Use
the directional arrows (
,
,
,
) on the projector or remote
control to navigate the image. Pressing D. ZOOM - reduces the size of
the image. When the - button is pressed again, the image is further
reduced until it is restored to the original size.
The Digital Zoom and Pan functions are also accessible in the DISPLAY
menu.
Correcting keystone
Keystoning occurs when the projector is not perpendicular to the screen and is where the
projected image displays visible as a trapezoid shape like either of the following:
•
Two parallel sides (left and right, or top and bottom) but is noticeably wider on either
side.
•
No parallel sides.
To correct the image's shape, you can perform the following steps.
1.
Adjust the projection angle. Move the projector to be in front of the center of the
screen with the base of the lens level with the top or bottom edge of the screen.
If the image is stilled distorted, or the projector is unable to be positioned as described
above, you will need to manually correct the image following ONE of these steps.
2.
•
Press one of the Keystone/Arrow buttons (
/
,
/
,
/
,
/
) on
the projector or remote control to display the Keystone correction page. Press
Operation
35
Download from Www.Somanuals.com. All Manuals Search And Download.
the button whose keystone icon is similar to the shape of the projected image.
Continue pressing the same button or press the other buttons until you are
satisfied with the shape.
•
Press MENU/BACK on the projector or remote
KEYSTONE
control. Go to the DISPLAY > Keystone menu and
press ENTER to display the Keystone correction
page. Press one of the Keystone/Arrow buttons
(
/
,
/
,
/
,
/
) on the projector
or remote control whose Keystone icon is similar to
the shape of the projected image. Continue pressing
the same button or press the other buttons until
you are satisfied with the shape.
Back
The values on the lower portion of the page change while pressing. When the values
reach their maximum or minimum with repeated button presses, the image's shape
will stop changing. You will not be able to change the image further in that direction.
•
Two parallel sides (left and right, or top and bottom) but is noticeably wider on
either side
•
•
Press
/
or
•
•
Press
/
or
Go to the Display >
Keystone menu. Enter
the Keystone correction
Go to the DISPLAY >
Keystone menu. Enter
the Keystone correction
page and press
repeatedly until the
image's shape becomes
square.
/
page and press
repeatedly until the
image's shape becomes
square.
/
•
No parallel sides
4. Press MENU/BACK to exit
and save the settings.
3. Press
until the image is square.
/
repeatedly
1. Press
/
or
2. Go to the Display >
Keystone menu. Enter the
keystone correction page
and press
/
.
36
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs
are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input source.
You can change the projected image ratio (no matter what aspect the source is) by pressing
ASPECT on the remote control or in the DISPLAY > Aspect Ratio menu. Select an aspect
ratio to suit the format of the video signal and your display requirements. There are four
aspect ratios available:
In the pictures below, the black portions are inactive areas and the white portions are active
areas.
1.
Auto: Scales an image proportionally to fit the projector's native
resolution in its horizontal width. This is suitable for the
incoming image which is neither in 4:3 nor 16:9 and you want to
make most use of the screen without altering the image's aspect
ratio.
2.
Actual Size: The image is projected as its original resolution, with no
pixel conversion. For input signals with lower resolutions, the
projected image will display smaller than if resized to full screen. You
could adjust the zoom setting or move the projector towards the
screen to increase the image size if necessary. You may also need to
refocus the projector after making these adjustments.
3.
4.
4:3: Scales an image so that it is displayed in the center of the screen
with a 4:3 aspect ratio. This is most suitable for 4:3 images like
computer monitors, standard definition TV and 4:3 aspect DVD
movies, as it displays them without aspect alteration.
16:9: Scales an image so that it is displayed in the center of the screen
with a 16:9 aspect ratio. This is most suitable for images which are
already in a 16:9 aspect, like high definition TV, as it displays them
without aspect alteration.
16:9 aspect ratio is only sourced through the Component Video input when
being fed an appropriate 16:9 aspect signal. See "Connecting a Component Video source
Operation
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the image
Selecting an application mode
The projector is preset with several predefined
application modes so that you can choose one to suit
your operating environment and input source picture
type. To select a operation mode that suits your need,
press MODE repeatedly until your desired mode is
selected. The picture modes available for different
types of signals are listed below.
PC/DVI-A/DVI-D Signal Input
1.
2.
3.
Presentation Mode (Default): Is designed for
presentations. The brightness is emphasized in
this mode to match PC and notebook coloring.
Brightest Mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
sRGB/Photo Mode: Maximizes the purity of RGB colors to provide true-to-life images
regardless of brightness setting. It is most suitable for viewing photos taken with an
sRGB compatible and properly calibrated camera, and for viewing PC graphic and
drawing applications such as AutoCAD.
4.
5.
Gaming Mode: Is suitable for playing PC-based games in a bright living room.
Video Mode: Is appropriate for playing movies, video clips from digital cameras or
DVs through the PC input for best viewing in a blackened (little light) environment.
User 1/User 2 Mode: Recalls the settings customized based on the current available
Memory Mode: Recalls settings made through the BRIGHTNESS and CONTRAST
buttons on the remote control. Any adjustments made by the BRIGHTNESS and
CONTRAST buttons will change the current application mode to Memory mode.
6.
7.
YPbPr/S-Video/Video Signal Input
1.
2.
3.
4.
Cinema Mode: Is suitable for enjoying DVD movies best viewed in a blackened (little
light) home cinema or lounge room environment.
Movie Mode (Default): Is suitable for enjoying colorful movies and TV in a home
darkened (not bright) lounge room lighting level environment.
Gaming Mode: Is suitable for playing gamebox-based video games in a normal living
room lighting level environment.
Photo Mode: Is perfect for viewing digital photos taken in daylight with an sRGB
compatible and properly calibrated camera, and for viewing Photo CDs. The color
saturation and brightness are well-balanced.
5.
User 1/User 2 Mode: Recalls the settings customized based on the current available
Setting the User 1/User 2 mode
There are two user-definable modes if the current available application modes are not
suitable for your need. You can use one of the application modes (except the User 1/2) as a
starting point and customize the settings.
1.
2.
Press MENU/BACK to open the On-Screen Display (OSD) menu.
Go to the PICTURE > Application Mode menu.
38
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
5.
6.
Press Left/ Right to select User 1 Mode to User 2 Mode.
Press Down to highlight Reference.
Press Left/ Right to select an application mode that is closest to your need.
Press Down to select a menu item to be changed and adjust the value with Left/
When all settings have been done, highlight Save Settings and press ENTER to store
the settings.
7.
8.
The confirmation message 'Setting Saved' displays.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or 2 mode is selected. You can make adjustments to these functions based on
your needs.
Adjusting brightness
Adjust the values by pressing Left/ Right on the projector or remote control.
The higher the value, the brighter the image. And lower the setting, darker the image. Adjust
this control so the black areas of the image appear just as black and that detail in the dark
areas is visible.
+70
50
-30
Adjusting contrast
Adjust the values by pressing Left/ Right on the projector or remote control.
The higher the value, the greater the contrast. Use this to set the peak white level after you
have previously adjusted the Brightness setting to suit your selected input and viewing
environment.
+70
-30
50
Selecting a color temperature
Adjust the values by pressing Left/ Right on the projector or remote control.
There are four color temperature* settings available.
1.
T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2.
3.
4.
T2: Makes images appear bluish white.
T3: Maintains normal colorings for white.
T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
39
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
4. Other adjustments
You can find other image quality fine-tune selections in the PICTURE menu as well. See
"Picture menu" on page 48 for details.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is higher than
3200 feet above sea level, or is hotter than 40°C, or whenever the projector will be used for
extended periods of time (>10 hours) without shutdown.
To activate the High Altitude Mode, go to
WARNING
SYSTEM SETUP: Advanced > High
Altitude Mode, select On by pressing Left/
High Altitude Mode is used when the
environment is higher than 3200 feet,
or the temperature is over 40°C.
Right on the projector or remote control. A
confirmation message displays. Highlight Yes
Do you want to turn the High Altitude
and press ENTER.
Mode on?
Operation under "High Altitude Mode" may
cause a higher decibel operating noise level
because of increased fan speed necessary to
improve overall system cooling and
performance.
No
Yes
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Hiding the image
In order to draw the audience's full attention to the
presenter, you can use BLANK on the projector and
remote control to hide the screen image. Press any
button (except LASER) on the projector and remote
control to restore the image. The word 'BLANK'
appears at the lower right corner of the screen while
the image is hidden. When this function is activated
with an audio input connected, the audio can still be
heard.
You can set a time length in the SYSTEM SETUP:
Basic > Blank Timer menu to shut down the projector after a period of time when there is
no action taken on the projector or remote control. The length of time can be set from 5 to
30 minutes in 5-minute increments.
If the preset time spans are not suitable for your personation, select Disable. No matter
Blank Timer is activated or disabled, you can press any button (except LASER) anytime you
want to restore the image.
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
40
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
PIP (Picture In Picture) operation
Your projector is capable of displaying images simultaneously from two input sources, which
can be used to enhance your presentation in an interesting way.
The PIP functions are available only when the input source is PC and the PIP source is Video
or S-Video.
1.
Ensure both the PC, and Video or S-Video signals are correctly connected to the
projector.
2.
3.
Display the PC image (Analog RGB) on the screen.
To display the PIP window, press PIP on the remote control or go to the DISPLAY >
PIP settings > PIP menu, select On by pressing Left/ Right.
To select a PIP-Source to be displayed, in the DISPLAY > PIP settings > Source menu,
press Left/ Right.
4.
5.
To change the position of the PIP image, press Left/ Right repeatedly in the
DISPLAY > PIP settings > Position menu until a suitable position is selected.
6.
To resize the PIP image, press Left/ Right once or twice in the DISPLAY > PIP
settings > Size menu to set the PIP size as small or large.
7.
8.
To adjust the PIP image quality, you can press Left/ Right in the DISPLAY > PIP
settings > Saturation or Hue menu.
To leave the OSD menu, press MENU/BACK twice.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Remote paging operations
Connect the projector to your PC or notebook with a USB cable prior to
using the paging function.
You can operate your display software program (on a connected PC)
which responds to page up/down commands (like Microsoft
PowerPoint) by pressing Page Up and Page Down on the remote control.
If remote paging function doesn't work, check if the USB connection is
correctly made and the mouse driver on your computer is updated to
the latest version.
Freezing the image
Press the FREEZE button on the remote control to freeze the image.
'FREEZE' will display in the upper right corner of the screen. To release
the function, press any button (except LASER) on the projector or remote
control.
Even if an image is frozen on the screen, the pictures are running on the
video or other device. If the connected devices have active audio output,
you will still hear the audio even though the image is frozen onscreen.
Creating your own startup screen
In addition to selecting the projector preset startup screen from among BenQ logo, Black or
Blue screen, you can make your own startup screen that is an image projected from your
computer or video source.
1.
Project the image you want to use as your startup screen from either a computer or
video source.
2.
Press CAPTURE on the remote control or go to the SYSTEM SETUP: Basic > My
Screen menu, press ENTER.
3.
4.
A confirmation message displays. Press CAPTURE or ENTER again.
The message 'Screen Capturing...' displays while the projector is processing the image.
Please wait.
5.
6.
If the action is successful, you see the message 'Captured Succeeded' on the screen. The
captured image is saved as My Screen.
To view the captured image displayed as the startup screen, set My Screen in the
SYSTEM SETUP: Advanced > Splash Screen menu and restart the projector.
In the unlikely event that the capturing action fails, change your target image.
42
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu Display Time in the SYSTEM SETUP: Basic > Menu Settings menu sets the
length of time the OSD will remain active after your last button press. The time length
ranges from 5 to 30 seconds in 5-second increments. Use Left/ Right to select a
suitable time.
•
•
•
Menu Position in the SYSTEM SETUP: Basic > Menu Settings menu sets the OSD
position in five locations. Use Left/ Right to select a preferred position.
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the On-
Screen (OSD) Menus. Use Left/ Right to select your language.
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be
displayed during projector start-up. Use Left/ Right to select a screen.
Shutting down the projector
I
1.
Press
Power and a confirmation
message will display prompting you.
If you don't respond in a few seconds,
the message will disappear.
I
2.
Press
Power a second time. The
Power indicator light flashes orange, the
projection lamp shuts down, and the
fans will continue to run for
approximately 90 seconds to cool down
the projector.
To protect the lamp, the projector will not respond to any commands during the cooling
process.
3.
4.
The Power indicator light is a steady orange once the cooling process has finished and
fans stop.
Disconnect the power cord from the wall
socket.
To save your time, you can unplug the projector as
soon as it is turned off without waiting for the cooling
time. The projector will continue cooling down even if
it is unplugged so that you can pack up the projector
and go. During the projector's off-line cooling, you
cannot restart it.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
Main menu Sub-menu
Options
Aspect Ratio
Keystone
Position
Auto/Actual Size/4:3/16:9
Phase
H. Size
Digital Zoom
Pan
DISPLAY
PIP
On/Off
Source
S-Video/Video
Bottom-Right/Bottom-Left/Top-
Left/Top-Right
Position
PIP Settings
Size
Small/Large
Saturation
Hue
PC source: Brightest/
Presentation/sRGB/Photo/
Gaming/Video/User 1/User 2/
Memory
Application Mode
Video source: Cinema/Movie/
Gaming/Photo/User 1/User 2
PC source: Brightest/
Presentation/sRGB/Photo/
Gaming/Video
Reference
Video source: Cinema/Movie/
Gaming/Photo
Brightness
Contrast
PICTURE
Saturation
Hue
Sharpness
Brilliant Color™
Color
Temperature
T1/T2/T3/T4
Gamma 1/Gamma 2/Gamma 3/
Gamma 4/Gamma 5/Gamma 6/
Gamma 7/Gamma 8/Gamma 9
Gamma
Save Settings
44
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Source Detection
Network
On/Off
SOURCE
English, French, German, Italian,
Spanish, Russian, Traditional
Chinese, Simplified Chinese,
Japanese, Korean, Swedish,
Dutch, Turkish, Czech,
Language
Portuguese, Thai, Polish
Front Table/Rear Table/Rear
Ceiling/Front Ceiling
Projector Position
Auto Power Off
Blank Timer
Disable/5 min/10 min/15 min/20
min/25 min/30 min
SYSTEM
SETUP:
Basic
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Splash Screen
My Screen
BenQ/My Screen/Black/Blue
Mute
On/Off
Audio Settings
Volume
5 sec/10 sec/15 sec/20 sec/30
sec
Menu Display Time
Menu Position
Menu Settings
Center/Top-Left/Top-Right/
Bottom-Right/Bottom-Left
Quick Cooling
On/Off
High Altitude Mode
On/Off
Lamp Mode
Normal/Economic
SYSTEM
SETUP:
Lamp Settings
Reset Lamp Timer Reset/Cancel
Lamp Timer
Advanced
Password
On/Off
Security Settings
Change Password
Reset All
Settings
Source
Application Mode
Resolution
Information
Color System
Lamp Timer
Note that the menu items are available when the projector detects at least one valid signal. If
there is no equipment connected to the projector or no signal detected, limited menu items
are accessible.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
details.
Below is the overview of the English OSD menu.
Main menu icon
Main menu
Highlight
Sub-menu
Status
Press MENU/
BACK to the
previous
page or to
exit.
Current input signal
The following example describes the adjustment of Keystone with the English OSD menus.
The adjustment methods mentioned below can also be applied when using different OSD
language other than English.
1.
Press MENU/BACK on the projector or
remote control to turn the OSD menu
on.
4.
Press ENTER to display the
keystone correction page.
KEYSTONE
Back
5.
6.
Based on the image shape
displayed on the screen, press
2.
3.
Use Left/ Right to select the
DISPLAY menu.
the keystone buttons (
/
Up,
/
Press Up/ Down to select Keystone.
/
Left, Down,
/
Right) to adjust the image to
a rectangular or square one.
Press MENU/BACK on the
projector or remote control
twice* to leave and save the
settings.
*The first press leads you back to the
main menu and the second press
closes the OSD menu.
46
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Display menu
FUNCTION
(default setting/
value)
DESCRIPTION (default setting/value)
There are four options to set the image's aspect ratio depending on your
input signal source.
Aspect Ratio
(Auto)
Corrects any keystoning of the image. See "Correcting keystone" on page
35 for details.
Keystone
(0)
Displays the position adjustment page. To move the projected image,
use the directional arrow buttons. The values shown on the lower
position of the page change with every button press you made until they
reach their maximum or minimum.
Position
(0)
Adjusts the clock phase to reduce image
distortion.
Phase
(depends on the
selected input
source)
Adjusts the horizontal width of the image.
H. Size
(depends on the
selected input
source)
Magnifies or reduces the projected image. See "Searching for details on
the projected image" on page 35 for details.
Digital Zoom
(100%)
Displays the Pan page for searching the details of the projected image by
using the directional arrow buttons on the projector or remote control
after the image is magnified.
Pan
PIP (Off)
Turns the PIP window on or off
Source (Video)
Selects the source for the PIP.
Position (Top-Left)
Selects a desired position for the PIP.
Size (Large)
PIP Settings
Selects a suitable size for the PIP.
Saturation (0)
Adjusts the color saturation level.
Hue (0)
Adjusts the red and green color tones of the image.
operation" on page 41 for details.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Picture menu
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
(default setting /
value)
DESCRIPTION
Pre-defined application modes are provided so you can optimize your
projector image set-up to suit your program type. See "Selecting an
application mode" on page 38 for details.
Application
Mode
(PC/DVI-A/DVI-
D: Presentation;
YPbPr/S-Video
Video: Movie)
Selects an application mode that most suits your need for the image
quality and further fine-tune the image based on the selections listed on
the same page below.
Reference
Adjusts the brightness of the image.
Brightness
(50)
Adjusts the degree of difference between dark and light in the image.
Contrast
(0)
Adjusts the color saturation level -- the amount of each color in a video
image. Lower setting produces less saturated colors; setting to the
minimum value makes the image black and white. If the setting is too
high, colors on the image will be overpowering, which makes the image
unrealistic.
Saturation
(0)
Adjusts the red and green color tones of the image. The higher the value,
the more greenish the image becomes. The lower the value, the more
reddish the image becomes.
Hue
(0)
Adjusts the image to make it look sharper or softer.
Sharpness
(16)
This feature utilizes a new color-processing algorithm and system level
enhancements to enable higher brightness while providing truer, more
vibrant colors in picture. It enables a greater than 50% brightness increase
in mid-tone images, which are common in video and natural scenes, so
the projector reproduces images in realistic and true colors. The range is
from "0" to "10". If you prefer a stronger enhanced image, adjust toward
the maximum setting. For a smoother, more natural image, adjust toward
the minimum setting. When set to "0", Brilliant Color is disabled.
Brilliant
Color™
(10)
There are four color temperature settings available.
Color
(T3)
48
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
The relationship between input signal and image brightness. The lower
the figure, the more black detail is visible.
•
Gamma 1, 4, and 8
Increases the average brightness of the image.
Best for a lit environment, meeting room or family room
Gamma 2: Gamma curve 2.5
•
•
•
Gamma
(Gamma 2)
Simulates the PC display standard.
Gamma 3, 6, and 9: Gamma curve 2.2 Video standard
Best for viewing movies in a darkened environment
Gamma 5, and 7: Gamma curve 1.8
Emphasizes black detail.
Best setting to view movies with a lot of dark detail, shadows etc.
Saves the settings made for User 1 or 2 mode.
Save
Settings
Source menu
FUNCTION
(default setting /
value)
DESCRIPTION
Sets whether the projector searches automatically for input signals. If the
source scan is On, the projector will scan for input signals until it acquires
a signal. If the function is not activated, the projector selects the last used
input signal. The default value is 'RGB'.
Auto Source
Detection
(On)
Displays the wireless connection menu.
Network
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
49
System setup: Basic menu
FUNCTION
(default setting /
value)
DESCRIPTION
Sets the language for the On-Screen Display (OSD) menus.
Use Left/ Right on the projector or remote control to select your
desired language. There are 17 languages for your choice: English
(default), French, German, Italian, Spanish, Russian, Traditional Chinese,
Simplified Chinese, Japanese, Korean, Swedish, Dutch, Turkish, Czech,
Portuguese, Thai, and Polish.
Language
(English)
The projector can be installed on a ceiling or behind a screen, or with one
or more mirrors. Contact your dealer for the ceiling mount bracket
(optional accessory) if you need to install the projector on your ceiling.
Projector
Position
(Front Table)
This function allows the projector to turn off automatically if no input
signal is detected after a set period of time. Press Left/
Right on the
projector or remote control to set the duration before the projector is
turned off.
Auto Power
Off
(Disable)
The time period can be set from 5 to 30 minutes in 5-minute increments.
If the preset time lengths are not suitable for your presentation, select
Disable. The projector will not automatically shut down in a certain time
period.
Sets the image blank time when the Blank feature is activated, once
elapsed the projector will shut down. See "Hiding the image" on page 40
for details.
Blank Timer
(Disable)
Allows you to select which logo screen will display during projector start-
up. Four options are available: BenQ logo, My Screen, Black screen, or
Blue screen.
Splash
Screen
(BenQ logo)
Captures and stores the projected image as My Screen. See "Creating your
own startup screen" on page 42 for details.
My Screen
Mute (Off)
Toggles the projector audio between on and off.
Audio
Settings
Volume (5)
Adjusts audio volume level.
Menu Display Time (15 sec)
Sets the length of time the OSD will remain active after your last button
press. The range is from 5 to 30 seconds in 5-second increments.
Menu
Settings
Menu Position (Center)
Sets the On-Screen Display (OSD) menu position.
50
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
System setup: Advanced menu
FUNCTION
(default setting /
value)
DESCRIPTION
Enables or disables the Quick Cooling function. Selecting On enables the
function and projector cooling time will be shortened from a normal 90-
second duration to approximately 30 seconds.
Quick
Cooling
(Off)
A mode for operation in areas like high altitude or high temperature.
High Altitude
Mode
(Off)
Lamp Mode (Normal)
Toggles the projector lamp between Normal and Economic modes. Using
Economic mode reduces system noise and power consumption by 20%. If
the Economic mode is selected, the light output will be reduced and result
in darker projected images.
Lamp
Setting the projector in Economic mode also extends the lamp timer
automatic shutdown feature. See "Calculation of lamp hour" on page 56
for details on how the total lamp hour is calculated.
Settings
Reset Lamp Timer
Once the lamp is renewed, select Reset to return the lamp timer to '0'.
Password (Off)
Limits use of the projector to only those who know the correct password.
When the function is activated for the first time, you have to set a
details. Once the password is set and this function is selected, the projector
is password-protected. Users who do not know the correct password can
not use the projector.
The password can be entered by using either the buttons on the projector
or the remote control.
Security
Settings
You will be inconvenienced if you activate the password functionality
and subsequently forget the password.
Print out this manual (if necessary) and write the password you used
in this manual, and keep the manual in a safe place for later recall.
The password will display as asterisks on-screen when being input.
Change Password
You will be asked to enter the current password before changing to a new
Returns all settings to the factory preset values.
Reset All
Settings
The following settings will still remain: Keystone, Position, Phase,
Projector Position, High Altitude Mode, Lamp Settings, and Security
Settings.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Information menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
Source
DESCRIPTION
Shows the current signal source.
Shows the selected mode in the PICTURE menu.
Application
Mode
Shows the native resolution of the input signal.
Resolution
Shows input system format, NTSC, PAL, SECAM, or RGB.
Displays the number of hours the lamp has been used.
Color System
Lamp Timer
52
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean and to clean the dust filter to prevent overheating.
Never remove any parts of the projector except the lamp and dust filter. Contact your dealer
if other parts need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
•
•
To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
Make sure the temperature and humidity of the storage area are within the
consult your dealer about the range.
•
•
•
Retract the adjuster feet.
Remove the batteries from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. When
you carry the projector yourself, please use the original box or provided soft carry case.
Cleaning and replacing the dust filter
It is necessary to clean the dust filter periodically. If the filter is not cleaned, it can become
clogged with dust and prevent proper ventilation. This can cause overheating and a
malfunction of the projector.
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
53
A warning message like the one pictured to the
right will be displayed for 10 seconds every 500
hours of use to remind you to clean the filter. To
leave the message, press ENTER on the projector or
remote control.
Clean the Air Filter
The air filter should be cleaned
every 500 hours of use.
If you have not done so, please
clean or replace the filter.
OK
To clean the filter
1.
Turn the projector off and wait until the fans
stop running.
2.
Locate the filter case on the back of the
projector.
Filter case
3.
Release the filter case from the projector by
pressing the filter case into the slot slightly. The filter case
springs out of the slot.
4.
5.
Pull out the filter case.
Use a small vacuum cleaner designed for
computers and other office equipment to clean the
filter sponge. Or use a soft brush (such as a clean
artist's paintbrush) to gently sweep the dust on the
filter away.
If the dirt is difficult to remove or the filter is
broken, replace it with the supplied spare filter
page.
54
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Refit the filter case by aligning and inserting it into
the projector slot.
7.
8.
Press the case back until it clicks into place.
Turn the projector back on.
If the case is not correctly seated in place, the
projector will display an on-screen message as
pictured to the right every three minutes.
WARNING
Check the Air Filter
The air filter is not installed well.
Please reinstall again.
The message will display 3 times for a 10-second
duration each, if no further action is taken.
OK
Then a second message as pictured to the right
displays to warn of shutdown in 1 minute.
Power Off
The air filter is not installed well.
Please reinstall again.
You can re-attach the case correctly anytime before
the projector shuts down. That means you have 10-
11 minutes to get the re-attachment done from the
time the first warning message was displayed. The
projector will return to normal operation.
Otherwise, the projector will be
turned off in 60 seconds.
Replacing the filter sponge
If you find the dirt is hard to remove from the filter sponge or the sponge is broken, replace
it.
1.
Carefully peel the filter sponge away from the filter case.
See that there are small plastic pins along the edges to
position and retain the sponge into place. Lift the sponge
up off these pins taking care to prevent them from
breaking off.
2.
Attach the supplied new filter sponge to the filter case.
Make sure that the tiny holes securely fit onto the case's
pins.
Plastic pins
Maintenance
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp information
Calculation of lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as
follows:
Total (equivalent) lamp hour
= 3/4 (hours used in Economic mode) +1 (hours used in normal mode)
The lamp hour in Economic mode is calculated as 3/4 of that in normal mode. That is, using
the projector in Economic mode helps to extend the lamp hour by 1/3.
Warning message
When the Lamp indicator lights up red or a message appears suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes
too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp
indicator still lights up after turning the power back on, please contact your dealer. See
"Indicators" on page 60 for details.
The following Lamp warning displays will remind you to change the lamp.
Message
Status
The lamp has been in operation for 2800 hours.
Install a new lamp for optimal performance. If the
projector is normally run with "Economic Mode"
you may continue to operate the projector until the
2950 hour lamp warning appears.
WARNING
Replace the Lamp
The lamp life is over 2800 hours.
If the projected image gets
darker, please replace the lamp.
OK
The lamp has been in operation for 2950 hours. A
new lamp should be fitted to avoid the
inconvenience of shutdown when the projector
runs out of lamp time.
WARNING
Replace the Lamp
Immediately
The lamp life is over 2950 hours.
Please replace the lamp, and reset
the lamp timer.
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced after 2950
hours usage.
OK
56
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
If this warning message displays, the projector will
shut down in 40 seconds. The lamp MUST be
replaced before the projector will operate normally.
Out of Lamp Usage Time
The projector will be shut down
automatically for safety issue.
Please replace the lamp as soon
as possible.
Replacing the lamp
•
•
•
•
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
To reduce the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of
this lamp in a proper manner.
1.
2.
Turn the power off and disconnect the projector from the wall socket. If the lamp is
hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
Turn the projector over. Then loosen the screw
on the lamp cover.
3.
Remove the lamp cover from the projector.
Do not turn the power on with the lamp cover removed.
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
57
4.
5.
6.
Disconnect the lamp connector from the
projector.
Loosen the screw that secures the lamp.
Lift the handle so that it stands up. Use the
handle to slowly pull the lamp out of the
projector.
•
•
Pulling it too quickly may cause the lamp to break
and scatter broken glass in the projector.
Do not place the lamp in locations where water
might splash on it, children can reach it, or near
flammable materials.
•
Do not insert your hands into the projector after the
lamp is removed. If you touch the optical
components inside, it could cause color
unevenness and distortion of the projected
images.
7.
As shown in the figure, hold the new lamp and
align the two locators on the lamp with the
holes on the projector, and then insert the lamp
all the way into the projector.
8.
Connect the lamp connector to the projector.
58
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Tighten the screw that secures the lamp.
•
Loose screw may cause a bad connection, which
could result in malfunction.
•
Do not over tighten the screw.
10. Ensure the handle is fully laid flat and locked in
place.
11. Replace the lamp cover on the projector.
12. Tighten the screw that secures the lamp cover.
•
Loose screw may cause a bad connection, which
could result in malfunction.
•
Do not over tighten the screw.
13. Restart the projector.
Do not turn the power on with the lamp cover removed.
14. After the startup logo, open the On-Screen
Display (OSD) menu. Go to the SYSTEM
SETUP: Advanced > Lamp Settings menu.
Press ENTER. The Lamp Settings page
WARNING
Reset Lamp Timer?
Cancel
Reset
displays. Highlight Reset Lamp Timer. A
warning message displays asking if you want
to reset the lamp timer. Highlight Reset and
press ENTER. The lamp time will be reset to '0'.
Do not reset if the lamp is not new or replaced as this could cause damage.
Temperature information
When the Temperature warning light is on, it is warning you of the following possible
problems:
1.
2.
The internal temperature is too high.
The fans are not working.
Turn the projector off and contact qualified service personnel for further help. For more
Maintenance
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicators
Illustration
•
•
Blank -: Light OFF
•
•
O: Orange light
R: Red light
: Light flashing
: Light ON
•
G: Green light
•
Light
Status & Description
Power Temp Lamp
Power events
The projector has just been connected to a power outlet.
O
O
G
G
O
O
Stand-by mode.
Powering up.
-
-
-
-
-
-
Normal operation.
1.
2.
The projector needs 90 seconds to cool down as it was
abnormally shut down without the normal cooling down
process. Or
The projector needs to cool for 90 seconds after the
power is turned off.
-
-
-
O
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
-
O
Lamp events
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
-
O
R
R
1.
2.
The projector needs 90 seconds to cool down. Or
Please contact your dealer for assistance.
-
-
60
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Light
Status & Description
Power Temp Lamp
Thermal events
-
-
-
-
R
R
R
R
R
R
R
R
R
R
R
R
R
G
G
R
G
O
R
G
O
R
G
O
R
G
O
R
O
R
R
R
G
G
G
O
O
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
O
-
-
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
There is no power from the power
cable.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input source device.
Check the connection.
The input signal has not been
correctly selected.
Select the correct input signal with the Source
key on the projector or remote control.
The lens cap is still attached to the
lens.
Remove the lens cap.
The digital video source connected to Connect using an analog input instead, such
the DVI input may be HDCP-
compliant.
as Component Video, S-Video, or composite
Video.
Blurred image
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the unit if necessary.
The lens cap is still attached to the
lens.
Remove the lens cap.
Remote control does not work
Cause
Remedy
The batteries are out of power.
Replace the batteries with new ones.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 6 meters (19.5 feet) of the
projector.
62
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
The computer projected image is too big for the screen or appeared to be cut-
off
Cause
Remedy
The computer's resolution does not
match the projector's resolution.
1.
Make sure the H Position and V Position
settings are correct in the Image menu.
Configure the computer's external
display resolution to the projector's
native resolution (1024 x 768 for
MP770). If this option is not available,
select one of the compatible listed in
2.
The computer's external monitor
setting is locked in 640 x 480.
3.
Check if your presentation files are
created for a different resolution.
My Window Media Player program works great on my computer, but the
movie window is dark on my projector, while the Media Player tools display
OK.
Cause
Remedy
Change the Display settings. Click Start >
Control Panel > Display > Settings >
Advanced > Display. See you computer
documentation for details, if you cannot find
the Display settings by following the
instructions above. Set the Monitor to Primary,
and the Panel to Secondary. You will see the
movie window on the projector image, while
the Panel movie window will be dark.
The computer external display is set
as a secondary display.
The remote mouse function does not work.
Cause
Remedy
Check the connection. See "Connecting a
computer" on page 22 for details.
If it still doesn't work, check the mouse driver.
See the mouse documentation for details.
The USB cable is not correctly
connected to the projector or
computer.
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Resolution
Display system
Lens F/Number
Lamp
1024 x 768 XGA
1-CHIP DMD
F=2.6 to 2.77, f= 20.4 to 23.5 mm
220 W lamp
Electrical
Power supply
Power consumption
AC100–240V, 1.5A–3.2A, 50/60 Hz (Automatic)
320 W (Max); 15 W (Standby)
Mechanical
Weight
6.6 lbs (2.99 Kg)
Input terminals
Computer input
RGB input
D-Sub 15-pin (female) x 1
DVI-I input
(Using DVI-A signal)
Video signal input
S-VIDEO
Mini DIN 4-pin port x 1
VIDEO
RCA jack x1
SD/HDTV signal input
Analog - D-Sub to Component RCA jack x 3 (using RGB
input)
Digital - DVI (HDTV only)
Audio signal input
Audio in
Stereo mini-jack x 1
Output terminals
RGB output
Audio output
Speaker
D-sub 15-pin (female) x 1
Stereo mini-jack (mixed mono)
(mixed mono) 2 watt x 1
Control
USB mouse control
RS-232 serial control
A/B series x 1
Mini Din 9 pin x 1
Environmental Requirements
Operating temperature
0°C ~ 40°C at sea level
Operating relative humidity 10% ~ 90% (without condensation)
Operating altitude
0–3000 feet at 0°C–40°C
3000–6000 feet at 0°C–30°C
6000–10000 feet at 0°C–23°C
64
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing chart
Supported timing for PC (including DVI-I) input
Horizontal
Resolution Frequency Frequency Frequency
(kHz) (Hz) (MHz)
Vertical
Pixel
Mode
640 x 400
31.47
70.089
25.176
640 x 400_70
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
XGA_70
XGA_75
XGA_85
SXGA_60
31.469
37.861
37.500
43.269
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.667
63.981
59.940
72.809
75.000
85.008
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
60.020
25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
108.000
640 x 480
800 x 600
1024 x 768
1280 x 1024
Supported timing for Component-YPbPr input
Horizontal
Frequency (kHz)
Vertical Frequency
(Hz)
Signal Format
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
Supported timing for Video and S-Video inputs
Color sub-
carrier
Frequency
(MHz)
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Video mode
NTSC
PAL
15.73
15.63
15.63
15.73
15.63
15.73
15.73
60
50
50
60
50
60
60
3.58
4.43
4.25 or 4.41
3.58
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
3.58
4.43
4.43
Specifications
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal
usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is
found to be defective within the warranty period, BenQ's only obligation and your exclusive
remedy shall be replacement of any defective parts (labor included). To obtain warranty
service, immediately notify the dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be in-
between 10% and 90%, temperature in-between 0°C and 40°C, altitude lower than 10000
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
For other information, please visit support.BenQ.com.
Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Regulation statements
FCC statement
CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
EEC statement
This machine was tested against the 89/336/EEC (European Economic Community) for
EMC (Electronic Magnetic Compatibility) and fulfills these requirements.
MIC statement
B class equipment (Household purpose info/telecommunications equipment)
This equipment has undergone EMC registration for household purpose, and can be used in
any area including residential area.
WEEE directive
Disposal of Waste Electrical and Electronic Equipment by users in private households
in the European Union.
This symbol on the product or on the packaging indicates that this can
not be disposed of as household waste. You must dispose of your waste
equipment by handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment. For more information
about recycling of this equipment, please contact your city office, the shop
where you purchased the equipment or your household waste disposal
service. The recycling of materials will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and
environment.
68
Regulation statements
Download from Www.Somanuals.com. All Manuals Search And Download.
|