SIIG II 150 User Manual

SATA II-150 PCI  
Quick Installation Guide  
Introducing the SATA II-150 PCI  
The SATA II-150 PCI is an ultra high-speed dual channel  
SerialATA Generation 2controller for use in PCI enabled  
systems.  
FeaturesandBenefits  
Add up to two high-speed SATA hard drives  
New Serial ATA cable easier to install & provides  
better air circulation  
Supports two SATA channels and data transfer rate  
up to 1.5Gb/ s (150MB/ s)  
Supports Native Command Queuing (NCQ) and  
SATA TCQ commands  
Onboard bus master engine relieves the system  
processor from book keeping and enhances  
performance  
Features independent 256-byte FIFOs per channel  
for host reads and writes  
Breaks the 137GB barrier! Works with various  
brands of large capacity Serial ATA hard disks  
Supports SATA hard disk hot-plugging  
Compliant with PCI 2.3  
Compliant with Serial ATA 1.0 specifications and  
complement of SATA II optional features  
1
04-0409D  
Hardware Installation  
Note: For low profile systems, replace the currently  
mounted bracket with the included low profile bracket.  
General instructions for installing the card are provided  
below . Since the d esign of computer cases and  
motherboards vary, refer to your computers reference  
manual for further information, if needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computer case for a few  
seconds. Avoid any contact with internal parts and  
handle cards only by their external edges.  
1. Turn OFF the power to your computer and any  
other connected peripheral devices.  
2. Unplug the power cord from the back of the  
computer.  
3. Remove your computers cover.  
4. Remove the slot bracket from an available PCI slot.  
5. To install the card, carefully align the card's bus  
connector w ith the selected PCI slot on the  
motherboard. Push the board down firmly, but  
gently, until it is well seated.  
6. Replace the slot bracket's holding screw to secure  
the card.  
7. If needed, connect the HDD LED pins to monitor  
HDD activity from the front panel of your chassis.  
8. Replacethecomputer cover and reconnect thepower  
cord.  
3
Driver Installation  
This section provides information on how to install the  
SATA II-150 PCI drivers for the following operating  
systems.  
Windows2000  
New Windows 2000 Installation  
A new installation of Windows 2000 requires a floppy  
disk for the driver installation. To make this floppy disk,  
copy the contents of the Floppy folder, found on the  
driver CD, onto a blank floppy disk then follow the  
directions below.  
1. Install the board and follow the Microsoft  
procedures to install Windows 2000 accordingly.  
2. Restart your system w hen prompted d uring  
Windows' installation.  
3. At the Windows 2000 Setup screen, press F6 to  
install the driver.  
4. Insert the driver diskette. Press S, then press Enter.  
5.  
Select INITIO INIC1620 S-ATA Adapter For  
Windows 2000 and press Enter.  
6. Press Enter to continue and follow on-screen  
instructions to complete the installation.  
Existing Windows 2000 Installation  
1. Install the board and boot up Windows 2000.  
2. At the Found New Hardware Wizard, click Next.  
3. Select Search for a suitable driver for my device  
(recommended) and click Next.  
4. Insertthedriver CD,checkCD-ROM drives,uncheck  
the other boxes, and click Next. Click Next again to  
continue.  
4
5. Click Yes, then click Finish.  
6. Restart Windows to complete the driver installation.  
WindowsXP/Server2003  
New Windows XP/Server 2003 Installation  
A new installation of Windows XP/ Server 2003 requires  
a floppy disk for the driver installation. To make this  
floppy disk, copy the contents of the Floppy folder,  
found on the driver CD, onto a blank floppy disk then  
follow the directions below.  
1. Install the board and follow the Microsoft  
procedures to install Windows accordingly.  
2. Restart your system when prompted by Windows'  
installation.  
3. At the Windows Setup screen, press F6 to install the  
driver.  
4. Insert the driver diskette. Press S then press Enter:  
32-bit: Select INITIO INIC1620S-ATA Adapter For  
Windows XP/2003 and press Enter.  
64-bit: Select INITIO INIC1620S-ATA Adapter For  
Windows XP/2003 AMD64  
5. Press Enter to continue and follow on-screen  
instructions to complete the installation.  
Existing Windows XP/Server 2003 Installation  
1. Install the board and boot up Windows  
2.  
At the Found New Hardware Wizard:  
XP (w/SP1or earlier)/Server 2003: continue to step #3.  
XP (w/SP2or later)/Server 2003(w/ SP1or later): select  
No, not at this time, then click Next.  
5
3. Insert the driver CD, select Install the software  
automatically (Recommended), then click Next,  
Next.  
4. Click Continue Anyway, then click Finish.  
5. Restart Windows to complete the driver installation.  
ToVerifyWindows2000/XP/2003Installation  
1. Right click My Computer and click Manage.  
2. Select Device Manager.  
3. Double click SCSI and RAID Controllers, then  
double click Initio inic1620 S-ATA Adapter.  
4. A message Thisdeviceisworkingproperlyis displayed,  
the driver has been correctly installed.  
WindowsVista(32-bit)  
New Windows Vista Installation  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. At Where do you want to install Windows?, click  
Load Driver.  
3. Insert driver CD, then click Browse.  
4. Double click CD Drive (D:). (change D: to match  
your CD-ROM drive letter).  
5.  
Highlight Vista32 folder, then click OK.  
6. Select In itio in ic1620 S-ATA Ad ap ter  
(D:\ Vista32\ 1620.inf), then click Next.  
7. Follow on-screen instructions to complete Windows  
Vista installation.  
6
Existing Windows Vista Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard, insert the  
driver CD, select Locate and install driver software  
(Recommended), then click Continue.  
3. Click Next, select Install this driver anyway, then  
click Close.  
4. Remove the driver CD and restart Windows to  
complete the installation.  
WindowsVista(64-bit)  
New Windows Vista Installation  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. At Where do you want to install Windows?, click  
Load Driver.  
3. Insert driver CD, then click Browse.  
4. Double click CD Drive (D:). (change D: to match  
your CD-ROM drive letter).  
5.  
Highlight Vista64 folder, then click OK.  
6. Select In itio in ic1620 S-ATA Ad ap ter  
(D:\ Vista64\ 1620.inf), then click Next.  
7. Follow on-screen instructions to complete Windows  
Vista installation.  
Existing Windows Vista Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard, insert the  
driver CD, select Locate and install driver software  
(Recommended), then click Continue.  
3. Click Next, select Install this driver anyway, then  
click Close.  
7
4. Remove the driver CD and restart Windows to  
complete the installation.  
To Verify Windows Vista Installation  
1. Right click Computer,click Manage,click Continue.  
2. Select Device Manager.  
3. Double click SCSI and RAID Controllers, then  
double click Initio inic1620 S-ATA Adapter.  
4. A message Thisdeviceisworkingproperlyis displayed,  
the driver has been correctly installed.  
WindowsServer2008(32-bit)  
New Windows 2008 Installation  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. At Where do you want to install Windows?, click  
Load Driver.  
3. Insert driver CD, then click Browse.  
4. Double click CD Drive (D:). (change D: to match  
your CD-ROM drive letter).  
5.  
Highlight Vista32 folder, then click OK.  
6. Select In itio in ic1620 S-ATA Ad ap ter  
(D:\ Vista32\ 1620.inf), then click Next.  
7. Follow on-screen instructions to complete Windows  
Vista installation.  
Existing Windows 2008 Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard, insert the  
driver CD, select Locate and install driver software  
(Recommended), then click Don't search online.  
3. Click I don't have the disc. Show me other options.  
8
4. Click Browse my computer for driver software  
(Advanced).  
5. Typ e in D :\ Vista32, (change D: to m atch  
your CD-ROM drive letter), then click Next.  
6. Click Install this driver software anyway,then click  
Close.  
7. Remove the driver CD and restart Windows to  
complete the installation.  
WindowsServer2008(64-bit)  
New Windows 2008 Installation  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. At Where do you want to install Windows?, click  
Load Driver.  
3. Insert driver CD, then click Browse.  
4. Double click CD Drive (D:). (change D: to match  
your CD-ROM drive letter).  
5.  
Highlight Vista64 folder, then click OK.  
6. Select In itio in ic1620 S-ATA Ad ap ter  
(D:\ Vista64\ 1620.inf) (x64), click Next, then click  
OK.  
7.  
Repeat steps 2-4, then continue to step #8.  
8. Hightlight Vista32 folder, then click OK.  
9. Select In itio in ic1620 S-ATA Ad ap ter  
(D:\ Vista32\ 1620.inf), click Next, then click OK.  
10. Follow on-screen instructions to complete Windows  
Vista installation.  
9
Existing Windows 2008 Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard, insert the  
driver CD, select Locate and install driver software  
(Recommended), then click Don't search online.  
3. Click I don't have the disc. Show me other options.  
4. Click Browse my computer for driver software  
(Advanced).  
5. Typ e in D :\ Vista64, (change D: to m atch  
your CD-ROM drive letter), then click Next.  
6. Click Install this driver software anyway,then click  
Close.  
7. Remove the driver CD and restart Windows to  
complete the installation.  
ToVerifyWindowsServer2008Installation  
1. Right click Computer, click Manage, double click  
Diagnostics, click Device Manager.  
2. Double click Storage controllers, then double click  
Initio INIC1620 S-ATA Adapter.  
4. A message Thisdeviceisworkingproperlyis displayed,  
the driver has been correctly installed.  
BIOS Configuration  
The SATA II-150 PCI BIOS will appear everytime your  
system starts up. If the BIOS doesn't show, please try  
your controller in another PCI slot. During this (Post)  
process, the BIOS will show up and indicate the devices  
attached to it.  
10  
Technical Support and Warranty  
QUESTIONS? SIIGs Online Support has answers! Simply visit our  
web site at www.siig.com and click Support. Our online support  
database is updated daily with new drivers and solutions. Answers  
to your questions could be just a few clicks away. You can also submit  
questions online and a technical support analysts will promptly  
respond.  
SIIG offersa lifetimemanufacturer warranty with thisproduct. Please  
see our web site for more warranty details. If you encounter any  
problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyour purchase has passed the store's return policy period,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #: __________________  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
11  
About SIIG, Inc.  
Founded in 1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
ofI/ O connectivity products,including PCI&ISA serialand parallel  
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/ b),  
networking, sound cards, and other accessories. SIIG is the premier  
one-stop source of upgrades.  
SIIG productsoffer comprehensiveuser manuals,many user-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
found in computer retail stores, mail order catalogs, through major  
distributors, system integrators, and VARs in the Americas and the  
UK,and through e-commerce sites.  
PRODUCT NAME  
SATA II-150 PCI  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Ph: 510-657-8688  
SATA II-150PCIis a trademark ofSIIG,Inc. SIIG and the SIIG logo are registered trademarks ofSIIG,  
Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of  
MicrosoftCorporation in theUnited Statesand/ or other countries. Pentium isa registered trademark  
of Intel Corporation. Other names used in this publication are for identification only and may be  
trademarksoftheir respectivecompanies.  
February, 2009  
Copyright © 2009 by SIIG, Inc. All rights reserved.  

Sony Net MD Walkman MZ N420D User Manual
SimpleTech Zeus Ultra User Manual
Samsung YP G70 User Manual
Samsung SGH N400 User Manual
Samsung GH68 27732A User Manual
Samsung Cell Phone GT S7562 User Manual
Samsung 20040611192609281 User Manual
RCA RP 7900A User Manual
Philips SPD5250 User Manual
Pantech PG 1410 User Manual