Addonics Technologies PPROEPU3 User Manual

T E C H N O L O G I E S  
User Guide  
Pocket UDD II  
(PUDDEPU3 / PUDDESP / PUDDES  
PPROEPU3 / PPROESP / PPROES)  
v6.1.11  
Technical Support  
If you need any assistance to get your unit functioning properly, please have your  
product information ready and contact Addonics Technical Support at:  
Hours: 8:30 am - 6:00 pm PST  
Phone: 408-453-6212  
Universal eSATAp Cable  
Hybrid eSATA Port  
(eSATAp)  
Standard eSATAp Cable  
eSATA Port  
Power Adapter or  
USB Power Cable  
Universal eSATAp Cable  
USB 3.0/2.0 Port  
eSATAp to USB 3.0 Adapter  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
Operation of the Pocket UDD II  
A.  
Pocket UDD II is connected via USB.  
1.  
Insert the media fully into the device using PCMCIA adapters and your operating system  
will report new hardware detected and begin to install the device. This may take a few  
seconds before a new drive icon appears in the My Computer folder. During this  
initialization, the LED light on the Pocket UDD II toggles between red and green color;  
and will stay green once the computer recognizes the media.  
2.  
Once the drive icon appears, the media is now ready and can be used like regular floppy  
media.  
3.  
4.  
During the read / write operation, the LED light of the Pocket UDD will blink red.  
To remove the media, click on the Safe Remove icon to stop the connection as shown  
below. Once the “you may now safely remove window” shows up, you can then remove  
the media from the Pocket UDD II by pushing on the eject button.  
Note:  
If you eject the media from the Pocket UDD without checking the Safe Remove icon, a  
warning message will appear from Windows 98SE, Me and 2000. This message is a  
reminder that it is safer to use the Safe Remove icon when you remove the media to  
prevent possible data loss in case you are in the middle of copying a file to and from the  
media. You can go ahead and close this message.  
5.  
Do not pull the media out of the device without using the eject button. This may crash the  
computer, as it does not realize the media has been manually removed from the device.  
B.  
Pocket UDD II is connected via eSATA  
Note:  
Before connecting the Pocket UDD II, it is assumed that you have installed the drivers of  
the eSATA controller card. You do not need to install any third-party driver for the Pocket  
UDD II.  
1.  
Insert the media fully into the device using PCMCIA adapters and your operating system  
will report new hardware detected and begin to install the device. This may take a few  
seconds before a new drive icon appears in the My Computer folder. During this  
initialization, the LED light on the Pocket UDD II toggles between red and green color;  
and will stay green once the computer recognizes the media.  
2.  
3.  
Once the drive icon appears, the media is now ready and can be used like regular floppy  
media.  
During the read / write operation, the LED light of the Pocket UDD will blink red.  
CONTACT US  
Phone:  
Fax:  
408-573-8580  
408-573-8588  
Email:  

Mr Coffee MPX23 User Manual
JVC KD LH5R User Manual
Hamilton Beach Single Serve Coffeemaker 49981 User Manual
Dell Computer Accessories AY511 User Manual
CyberPower CP H743P User Manual
Centon electronic DataStick Pro DSP32GB 002 User Manual
Bunn TSR 1 User Manual
Braun Sommelier KF 610 User Manual
Black Box Computer Accessories ACU5052A User Manual
Autodesk Computer Accessories 15607 010000 5000A User Manual