Sharp TCADH2564RCZZ User Manual

XE-A506 Quick Start Guide  
English  
The following describes how to get the cash register ready for operation. Follow these steps before using the cash register for the first time.  
Place the cash register on a stable, flat surface not subject to direct sunlight.  
Connecting the Barcode Scanner  
Initializing the Cash Register  
1
2
A barcode scanner is provided with the cash register. To use  
the scanner, connect the scanner before turning on the register.  
To ensure the cash register operates properly, please use the following procedure:  
1. Make sure the power cord plug is not inserted into the AC outlet.  
REG  
MGR  
OPX/Z  
OFF  
X1/Z1  
X2/Z2  
2. Insert the manager (MA) key into the mode switch and turn it to the PGM position.  
VOID  
PGM  
1. Open the Scanner port cover at the right side of the register.  
2. Insert the connector of the  
barcode scanner into the  
3. While holding down both the  
key and the  
key, insert the plug into the AC outlet. The buzzer will  
}
l
sound three times and “***MRS.***” will be displayed.  
Scanner port, and tighten both  
screws on the connector.  
4. The cash register has now been initialized.  
The register display will show “0.00” with “PGM”.  
CAUTION: • Always unplug the power cord of the cash register  
when you connect or disconnect the barcode scanner.  
• Never connect devices other than the barcode scanner  
before changing the interface setting. Otherwise  
malfunction of the cash register will occur.  
CAUTION: To charge the rechargeable batteries, keep the power on for one or two days. Leave the register with the mode  
switch in a position other than “OFF”.  
NOTE: If you press a key by mistake, an error message may be displayed. Press the  
key to clear message after installing paper rolls.  
l
Preparing the Cash Register  
Installing the Paper Rolls  
3
4
1. Push the printer cover forward and  
1. Cut off approximately one revolution  
of each paper roll. Make sure the  
paper end is cut as illustrated right.  
For journal paper installation  
5. Set a paper roll in the paper cradle of the journal side as  
detach it.  
illustrated in step 2.  
Correct  
Incorrect  
6. Insert the end of the paper into the paper chute until it is  
caught by the printer auto-feed and comes out the top of  
the printer. If the printer does not catch the paper, feed  
For receipt paper installation  
2. Remove the white retainer at the  
To the printer  
Retainer  
2. Set a paper roll in the paper cradle  
of the receipt side (upper side) as  
illustrated right.  
position shown right.  
Correct  
the paper while pressing  
as illustrated in step 3.  
}
NOTE: Please keep this retainer for future  
use when transferring the cash  
register.  
7. Insert the end of the paper into the  
slit in the take-up spool and fold  
the paper to front side, then wind  
the paper two or three turns  
To the printer  
Incorrect  
3. Move the print head release lever  
Slit  
3. Insert the end of the paper into the  
paper chute until it is caught by the  
printer auto-feed and comes out  
the top of the printer. If the printer  
does not catch the paper, feed the  
around the spool shaft. (Press  
}
upwards as illustrated right.  
Print head  
release lever  
to feed more paper if required.)  
8. Set the spool on the bearing, and  
press the  
excess slack in the paper.  
key to take up  
}
paper while pressing  
.
}
9. Replace the printer cover.  
4. Cut off the excess paper with the paper cutter.  

Yamaha KP125 User Manual
Toshiba TEC FS 1450 User Manual
Tektronix Camcorder 1780 R User Manual
Sony EX405 User Manual
Sony DT 55 300mm F4.5 5.6 SAM User Manual
Sony DCR PC3 User Manual
Sony Car Stereo System CDX GT260 User Manual
Samsung SC D263 User Manual
Samsung 2063UW User Manual
Rosen Entertainment Systems AV7500 AV HD1627 B25 User Manual