XV-Z17000
PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
Introduction
IMPORTANT
• For your assistance in reporting the loss or theft of
your Projector, please record the Serial Number lo-
cated on the bottom of the projector and retain this
information.
• Before recycling the packaging, please ensure that
you have checked the contents of the carton thor-
oughly against the list of “Supplied accessories” on
page 9.
Model No.: XV-Z17000
Serial No.:
High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
WARNING:
To reduce the risk of fire or electric shock, do not expose this product to rain
or moisture.
See bottom of projector.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
WARNING:
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not ex-
pressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal
of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities, the Electronics Industries Al-
1-800-BE-SHARP.
U.S.A. ONLY
This product contains a CR Coin Lithium Battery which contains Perchlorate Material – special handling may apply,
U.S.A. ONLY
-1
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the operation manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL XV-Z17000
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP (1-800-237-4277)
Caution Concerning Lamp Replacement
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed
to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a
lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of
use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be
replaced with a new one immediately, even if the lamp appears to be operating normally.
Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it
is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented
into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp
breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or
injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before
removing the lamp unit.
• Do not touch the glass surface of the lamp unit or the inside of the projector.
• Do not loosen other screws except for the lamp unit cover and lamp unit.
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use
the same lamp, this may cause the lamp to become damaged or explode.
Carefully change the lamp by following the instructions described on pages 62 to 64.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service
Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
-2
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read this Operation Manual
The specifications are slightly different, depending on the model. However, you can connect and operate all models
in the same manner.
• In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly
from the actual display.
Using the Menu Screen
Ad ustment uttons
(ꢀ/ꢁ/?/_)
MENU utton
Buttons used in this operation
ENTER utton
Ad ustment uttons
(ꢀ/ꢁ/?/_)
ENTER utton
RETURN utton
MENU utton
RETURN utton
• Press RETURN
to return to the
previous screen
hen the menu is
displa ed.
Menu Selections (Adjust-
ments)
Button used in this step
On-screen display
• This operation can also e performed
using
Example: “Picture” menu screen when
COMPONENT is selected for
input mode
the uttons on the pro ector.
Press MENU.
• The Picture menu screen for the se-
1
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Menu bar
Standard
lected input mode is displa ed.
0
0
0
0
0
0
0
0
Color
Tint
Sharp
Red
Press _ or ? to select the menu
screen to adjust on the menu
bar.
2
Blue
CLR Temp
IRIS1 (Manual)
High Brightness
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
On
Off
SEL./ADJ.
RETURN
ENTER
END
-35
............ Indicates safeguards for using the projector.
............ Indicates additional information for setting up and operating the projector.
Info
Note
For Future Reference
Maintenance
Troubleshooting
Index
P. 59
PP. 72 to 74
P. 78
-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Introduction
Setup
How to Read this Operation Manual .............3
Contents...........................................................4
IMPORTANT SAFEGUARDS............................6
Accessories .....................................................9
Part Names and Functions...........................10
Using the Remote Control............................13
Inserting the Batteries.......................................... 13
Usable Range ..................................................... 13
Setting Up the Projector...............................16
Setting Up the Projector...................................... 16
Standard Setup (Front Projection)........................ 16
Projection (PRJ) Mode......................................... 17
Ceiling-mount Setup ........................................... 17
Screen Size and Projection Distance................... 18
Connections
Samples of Cables for Connection..............19
Connecting to Video Equipment ..................20
Connecting to a Computer...........................21
Controlling the Projector by a Computer....22
Quick Start
Quick Start .....................................................14
Using
Setting the Resolution ......................................... 41
Auto Sync (Auto Sync Adjustment)...................... 41
Signal Type Setting.............................................. 41
Setting the Video System.................................... 42
Setting the Video Setup....................................... 42
Adjusting the Dynamic Range ............................. 42
Signal Info........................................................... 42
Adjusting the Projected Image (“SCR-ADJ” Menu)...43
Setting the Resize Mode ..................................... 43
Adjusting the Image Position............................... 43
Adjusting the Overscan ....................................... 43
Auto V-Keystone Correction................................ 44
Keystone Mode Correction.................................. 44
Setting On-screen Display................................... 45
Setting the Brightness of the Menu Screen.......... 45
Selecting the Background Image......................... 45
Selecting the Menu Screen Position .................... 45
Reversing/Inverting Projected Images.................. 45
Selecting the On-screen Display Language ......... 45
Adjusting the Projector Function (“PRJ-ADJ” Menu)...46
Setting Auto Power Off Mode.............................. 46
Setting the Power Save Mode (Economy Mode) ... 46
Setting One Touch Play, System Standby
Basic Operation
Turning the Projector On/Off........................23
Connecting the Power Cord................................ 23
Turning the Projector On ..................................... 23
Turning the Power Off
(Putting the Projector into Standby Mode)..... 23
Image Projection ...........................................24
Adjusting the Projected Image............................. 24
Keystone Correction............................................ 25
Switching the Input Mode.................................... 27
Adjusting the Vertical and Horizontal Position of the Image... 27
Displaying the Black Screen Temporarily ............. 28
Freezing a Moving Image..................................... 28
Auto Sync (Auto Sync Adjustment)...................... 28
Selecting the Picture Mode ................................. 28
Displaying an Enlarged Portion of an Image......... 29
Switching the Iris Setting..................................... 29
Hiding the Menu Temporarily (Menu Hide) ........... 29
Switching the Eco+Quiet Mode........................... 29
Resize Mode....................................................... 30
Useful Features
and Input Name............................................ 46
Setting the Demo Mode....................................... 47
Selecting the Transmission Speed (RS-232C)...... 47
Fan Mode Setting................................................ 47
Returning to the Default Settings......................... 47
Lamp Timer (Life) ................................................ 47
Menu Bar Items .............................................32
Using the Menu Screen.................................35
Menu Selections (Adjustments) ........................... 35
Picture Adjustment (“Picture” Menu) ..........37
Selecting the Picture Mode ................................. 37
Adjusting the Image ............................................ 37
Switching the Iris Setting..................................... 38
Eco+Quiet........................................................... 38
Using the Advanced............................................ 38
Correcting Gradation of Video (Gamma Correction) ... 38
Adjusting the Colors............................................ 38
Adjusting the Bright Boost................................... 40
Selecting the Film Mode...................................... 40
Setting Detail Enhancement ................................ 40
Reducing Image Noise (DNR).............................. 40
Mosquito Noise Reduction (MNR) ....................... 40
Resetting All Adjustment Items............................ 40
Computer Image Adjustment (“SIG-ADJ” Menu)...41
Adjusting the Computer Image............................ 41
Enjoying 3D Image Viewing……………….…48
Precautions on using 3D Glasses........................ 48
Precautions on viewing 3D images...................... 48
Supplied Accessories for 3D Glasses.................. 50
Part Names......................................................... 50
Before Using the 3D Glasses............................... 51
Replacing the Button Cell Battery........................ 51
Attaching the Nose Pad ...................................... 52
Attaching the 3D Glasses Band........................... 52
Using the 3D Glasses.......................................... 52
Usage Range of the 3D Glasses.......................... 52
Viewing 3D Images ............................................. 53
3D Settings (“3D MENU”).................................... 55
Setting the 3D Format Menu ............................... 56
Specifications – 3D Glasses ................................ 58
-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Appendix
Connecting Pin Assignments.......................65
RS-232C Specifications and Commands....66
Compatibility Chart .......................................70
Troubleshooting.............................................72
For SHARP Assistance..................................75
Specifications ................................................76
Dimensions ....................................................77
Index ...............................................................78
Maintenance ..................................................59
Maintenance Indicators................................60
Regarding the Lamp......................................62
Lamp .................................................................. 62
Caution Concerning the Lamp............................. 62
Replacing the Lamp............................................ 62
Removing and Installing the Lamp Unit................ 63
Resetting the Lamp Timer................................... 64
• DLP® and the DLP logo are registered trademarks of Texas Instruments.
•
Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instru-
ments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or
discompile the contents thereof.
-5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to as-
sure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for
its installation, use and servicing.
1. Read Instructions
13. Power-Cord Protection
All the safety and operating instructions should be read before
the product is operated.
Power-supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
2. Retain Instructions
The safety and operating instructions should be retained for
future reference.
14. Lightning
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cable system.
This will prevent damage to the product due to lightning and
power-line surges.
3. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
15. Overloading
5. Cleaning
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
16. Object and Liquid Entry
6. Attachments
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product.
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
17. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged in any
way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
9. Transportation
A product and cart combination should
be moved with care. Quick stops, exces-
sive force, and uneven surfaces may
cause the product and cart combination
to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
or other hazards.
20. Safety Check
11. Power Sources
Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine
that the product is in proper operating condition.
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
21.
Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
12. Grounding or Polarization
This product is provided with one of the following types of plugs.
If the plug should fail to fit into the power outlet,
please contact your electrician.
22. Heat
This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass particles
if lamp ruptures. In case of lamp
rupture, contact your nearest Sharp
Authorized Projector Dealer or Service
Center for replacement.
Warning about placing the projector in a high
position
When placing the projector in a high position, make cer-
tain it is carefully secure to avoid personal injury caused
by the projector falling down.
See “Regarding the Lamp” on page
62.
Do not subject the projector to hard impact
and/or vibration.
Protect the lens so as not to hit or damage the surface
Caution concerning the setup of the projector
For minimal servicing and to maintain high image quality,
SHARP recommends that this projector be installed in
an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the vents and lens must be cleaned more often. As
long as the projector is regularly cleaned, use in these
environments will not reduce the overall operation life of
the unit. Internal cleaning should only be performed by
a Sharp Authorized Projector Dealer or Service Center.
of the lens.
Rest your eyes occasionally.
Continuously watching the screen for long hours will
cause eye strain. Take regular breaks to rest your eyes.
Avoid locations with extremes of temperature.
The operating temperature of the projector is from 41°F
to 95°F (+5°C to +35°C).
The storage temperature of the projector is from –4°F
to 140°F (–20°C to +60°C).
Do not set up the projector in places exposed to
direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes out
the colors, making viewing difficult. Close the curtains
and dim the lights when setting up the screen in a sunny
or bright room.
Do not block the exhaust and intake vents.
Allow at least 1113/16 inches (30 cm) of space between
the exhaust vent and the nearest wall or obstruction.
Ensure that the intake vent and the exhaust vent are not
obstructed.
If the cooling fan becomes obstructed, a protection
circuit will automatically put the projector into standby
mode to prevent overheat damage. This does not indi-
cate a malfunction. (See page 60.) Remove the projector
power cord from the wall outlet and wait at least 10 min-
utes. Place the projector where the intake and exhaust
vents are not blocked, plug the power cord back in and
turn on the projector. This will return the projector to the
normal operating condition.
Caution regarding placing of the projector
Place the projector on a level site within the adjustment
range (9 degrees) of the adjustment foot.
Caution regarding usage of the projector
If you are not to use the projector for a long time or
before moving the projector, make certain you unplug
the power cord from the wall outlet, and disconnect any
other cables connected to it.
After the projector is purchased, a faint smell from the
vent may appear when the power is first turned on. This
is normal and is not a malfunction. It will disappear after
the projector is used for a while.
Do not carry the projector by holding the lens.
When storing the projector, ensure that you close the
lens shutter.
Do not expose the projector to direct sunlight or place
next to heat sources. Doing so may affect the cabinet
color or cause deformation of the plastic cover.
When using the projector in high-altitude areas
such as mountains (at altitudes of approximate-
ly 4,900 feet (1,500 meters) or more)
When you use the projector in high-altitude areas with
thin air, set “Fan Mode” to “High”. Neglecting this can
affect the longevity of the optical system.
Use the projector at altitudes of 7,500 feet (2,300 meters)
or less.
-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connected equipment
Temperature monitor function
When connecting a computer or other audio-visual
equipment to the projector, make the connections
AFTER unplugging the power cord of the projector
from the AC outlet and turning off the equipment to be
connected.
Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
If the temperature inside the projector increases, due
to blockage of the air vents, or the setting location,
the temperature warning indicator will blink. And if the
temperature keeps on rising, “
” will illuminate in
the lower left corner of the picture with the temperature
warning indicator blinking. If this state continues, the
lamp will turn off, the cooling fan will run and then the
projector will enter standby mode. Refer to “Maintenance
Indicators” on pages 60 and 61 for details.
Using the projector in other countries
The power supply voltage and the shape of the plug may
vary depending on the region or country you are using the
projector in. When using the projector overseas, make
sure you use an appropriate power cord for the country
you are in.
Info
• The cooling fan regulates the internal temperature,
and its performance is automatically controlled.
The sound of the fan may change during projector
operation due to changes in the fan speed. This
does not indicate malfunction.
Observe the following safeguards when using the 3D Glasses.
Prevention of accidental ingestion
Keep the batteries and band accessory out of the
reach of small children. Small children can accidentally
swallow these parts.
Using the 3D Glasses
Parents/guardians should monitor children’s view-
ing habits to avoid their prolonged use without rest
periods.
– If a child accidentally swallows any of these parts,
seek immediate medical attention.
Use only the 3D Glasses recommended for this product.
Use the 3D Glasses only for the specified purpose.
Do not move around while wearing the 3D Glasses. The
surrounding area appears dark, which may result in
falling or other accidents that may cause injury.
Do not disassemble
Do not disassemble or modify the 3D Glasses.
Caring for the 3D Glasses
Caution for lithium battery
Use only the cloth provided with the 3D Glasses to clean
the lenses. Remove dust and soil from the cloth. Any
dust or other soiling on the cloth may result in scratches
on the product. Do not use solvents such as benzene
or thinners as doing so may cause the coating to peel
off.
When cleaning the 3D Glasses, take care not to allow
water or other fluids to come into contact with the
glasses.
Batteries must not be exposed to excessive heat such
as direct sunlight or fire.
Replace only with the same or equivalent type of battery.
The battery may explode if improperly replaced.
Take care not to reverse the battery poles (+ and –)
when loading the battery. Follow the correct procedure
when loading the battery. (See page 51.) Loading the
battery incorrectly may damage the battery or cause it
to leak battery fluid, which could result in a fire, injury or
damage.
Always store the 3D Glasses in the case provided when
not in use.
When storing the 3D Glasses, avoid very humid or hot
locations.
Handling the 3D Glasses
Do not drop, exert pressure on, or step on the 3D
Glasses. Doing so may damage the glass section, which
may result in injury.
Be careful not to trap your finger in the hinge section of
the 3D Glasses. Doing so may result in injury.
– Pay special attention when children are using this
product.
Viewing 3D images
If you experience dizziness, nausea, or other discomfort
while viewing 3D images, discontinue use and rest your
eyes.
Do not use the 3D Glasses if they are cracked or bro-
ken.
-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Remote control
<RRMCGA929WJSA>
Two AA size batteries
<UBATUA020WJZZ>
Two pairs of 3D Glasses*1
<KOPTLA002WJN1>
Power cord*2
(1)
(2)
(3)
(4)
For U.S. and
Canada, etc.
(6' (1.8 m))
For Europe,
except U.K.
(6' (1.8 m))
For U.K. and
Singapore
(6' (1.8 m))
For Australia,
New Zealand and Oceania
(6' (1.8 m))
<QACCDA007WJPZ> <QACCVA011WJPZ> <QACCBA036WJPZ>
<QACCLA018WJPZ>
*1 See pages 50 to 52 for details of the 3D Glasses and their accessories.
*2 Which power cords are supplied along with your projector depends on the region. Use the power cord that
corresponds to the wall outlet in your country.
• Operation manual <TINS-E929WJZZ>
Note
• Codes in “< >” are Replacement parts codes.
Optional accessories
Lamp unit
AN-K15LP
Ceiling-mount adaptor
Ceiling-mount bracket
Ceiling-mount unit
AN-60KT
AN-XRCM30 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XRCM30>
(for U.S.A. only)
Ceiling-mount extension tube
3 RCA to mini D-sub 15 pin cable (10' (3.0 m))
AN-C3CP2
3D Glasses
AN-3DG10-S
AN-3DG10-R
AN-3DG10-A
Note
• Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Projector Dealer or Service Center.
-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector
10 11
12 13 14 15 16 17
1
2
3
4
5
6
7 8 9
18 19 20 21
Front View
Top View
1
2
Exhaust vent 59
10 Temperature warning indicator 60
11 Lamp indicator 23, 60
12 Power indicator 23, 60
13 STANDBY/ON button 14, 23
For turning the power on and putting the projector into
standby mode.
Zoom ring 15, 24
For enlarging/reducing the picture.
3
Focus ring 15, 24
For adjusting the focus.
23, 28, 63
Lens shutter
4
5
IR (infrared) emitter 52
14 3D MENU button 53
Emits an infrared signal when 3D images are
projected.
For displaying the 3D MENU screen.
15 PICTURE MODE button 28
6
7
8
9
Adjustment foot 15, 24
Remote control sensor 13
HEIGHT ADJUST lever 24
Intake vent 59
For selecting the appropriate picture.
16 ENTER button 35
For setting items selected or adjusted on the menu.
17 INPUT buttons (P/R) 27
For switching input mode.
18 RESIZE button 30
For switching the picture size (NORMAL, 16:9, etc.).
19 MENU button 35
For displaying adjustment and setting screens.
20 RETURN button 35
For returning to the previous menu screen during menu
operations.
21 Adjustment buttons (P/R/O/Q) 35
For selecting menu items.
-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector (Rear View)
1
2
3
4
5
6
11
7
8 9
10
Using the Carrying Handle
When transporting the projector,
carry it by the carrying handle on
the side.
• Always close the lens shutter to
prevent damage to the lens when
transporting the projector.
• Do not lift or carry the projector
by the lens as this may damage
the lens.
Terminals
1
2
3
4
5
RS-232C terminal 22
6
7
VIDEO input terminal 19
Terminal for controlling the projector using a
computer.
Terminal for connecting video equipment.
Carrying handle
For carrying the projector.
COMPONENT terminals 19
Terminal for connecting video equipment with
component output terminal.
8
9
Remote control sensor 13
AC socket 23
COMPUTER/COMPONENT
Connect the supplied power cord.
input terminal 19, 21
Terminal for computer RGB and YPbPr signals.
10 Kensington Security Standard connector
11 Security bar
HDMI1, 2 terminals 19, 20
Terminal for connecting video equipment with
HDMI output terminal.
S-VIDEO input terminal 19, 20
Terminal for connecting video equipment with
an S-video terminal.
Using the Kensington Lock
•This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System.
Refer to the information that came with the system for instructions on how to use it to secure the projector.
-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions (Continued)
Numbers in
refer to the main pages in this operation manual where the topic is explained.
1
2
3
ON button 14, 23
Remote Control
For turning the power on.
STANDBY button 15, 23
For putting the projector into the standby mode.
1
HDMI1, 2, COMPONENT, S-VIDEO, VIDEO,
COMPUTER buttons
For switching to the respective input modes.
2
3
4
15, 27
4
5
6
7
8
FREEZE button 28
For freezing images.
11
12
MAGNIFY buttons 29
For enlarging/reducing part of the image.
5
6
13
14
KEYSTONE button 25
For entering the Keystone mode.
Adjustment buttons (P/R/O/Q) 35
For selecting and adjusting menu items.
7
15
RETURN button 35
For returning to the previous menu screen during menu
operations.
16
17
9
INPUT button 27
For switching input mode.
8
9
18
10 3D ON/OFF button 53, 54
For switching between 2D and 3D modes.
19
20
10
11 AUTO SYNC button 28
For automatically adjusting images when connected to
a computer.
12 PICTURE MODE button 28
For selecting the appropriate picture.
13 IRIS 1, 2 buttons 29
For switching “High Brightness” and “High Contrast”.
14 IMAGE SHIFT button 27
For shifting images horizontally and vertically.
15 ENTER button 35
For setting items selected or adjusted on the menu.
16 MENU HIDE button 29
For temporarily hiding menu screen.
17 MENU button 35
For displaying adjustment and setting screens.
18 RESIZE button 30
For switching the picture size (NORMAL, 16:9, etc.).
19 3D MENU button 53
For displaying the 3D MENU screen.
20 ECO+QUIET button 29
For lowering the noise of the cooling fan and extending
the lamp life.
-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Inserting the Batteries
Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
Insert the supplied batteries and
put back the cover.
• Make sure the polarities correctly match
the mand nmarks inside the battery
compartment.
• When putting back the cover, be sure that
the cover clicks in place and settles.
30°
30°
Usable Range
23' (7 m)
The remote control can be used to control
the projector within the ranges shown in the
illustration.
Remote
control
sensors
Note
• Remote control sensor is located on both the
front and rear of the projector.
• The signal from the remote control can be
reflected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
30°
30°
23' (7 m)
When using the remote control:
• Be sure not to drop, expose to moisture or high
temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the projec-
tor away from the fluorescent lamp.
Remote control
signal transmitter
Remote control
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
•
Insert the batteries making sure the polarities correctly match the
m
and
n
marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them
using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept. Be
sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
This section provides an example showing how to connect the projector to video equipment that has an HDMI
output terminal with a brief explanation of the steps from connection through to image projection.
For details, see the pages suggested in each step.
3, 7 STANDBY/ON
7 STANDBY button
button
3 ON button
5 Input Mode
Select buttons
6 Zoom ring
5 INPUT button
6 Focus ring
6 Adjustment feet
Page 16
1.Place the projector facing a screen
2.
3.
-14
Connect the projector to the video equipment and plug
the power cord into the AC socket of the projector
Pages 19-23
Page 23
Open the lens shutter fully and then turn the projector on
On the projector
Press STANDBY/ON on the projector or ON on the
remote control pointing the remote control towards
the projector.
2
STANDBY/ON button
On the remote control
2
1
ON button
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Turn the video equipment on and start playback
Playback
Page 27
5.Select the input mode
Press HDMI1 on the remote control to select “HDMI1” for the Input mode.
HDMI1
YPbPr
1080P
HDMI1 button
• Press HDMI1, HDMI2, COMPONENT, S-VIDEO, VIDEO and COMPUTER on the remote control to
switch the Input mode.
• Press Por Rto select your desired input mode when you press INPUT on the remote control or on the
projector.
Page 24
6.Adjust the projector angle, focus and zoom
1. The focus is adjusted by
rotating the focus ring.
2. Zooming is adjusted by
rotating the zoom ring.
3. The projector angle is
adjusted by using the
adjustment feet.
Focus ring
Zoom ring
Adjustment feet
• When the image is distorted
trapezoidally, the keystone
correction is needed.
(See page 25.)
Page 23
7.Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again
while the confirmation message is displayed, to put the projector into standby mode.
On the projector
On the remote control
On-screen display
1
STANDBY/ON button
1
STANDBY
button
2
-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and
level.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly
on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when
setting up the screen in a sunny or bright room.
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according to the desired picture size.
Example of standard setup
Side View
Screen
H
Lens center
90°
L
Note
• Refer to page 18 for additional information concerning “Screen Size and Projection Distance”.
-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most ap-
propriate for the projection setting in use. (You can set the PRJ Mode in “SCR-ADJ” menu. See page 45.)
Table mounted, front projection
Ceiling mounted, front projection
Menu item “Front”
Menu item “Ceiling + Front”
Table mounted, rear projection
Ceiling mounted, rear projection
(with a translucent screen)
(with a translucent screen)
Menu item “Rear”
Menu item “Ceiling + Rear”
Ceiling-mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before
mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain
the recommended ceiling-mount adaptor and unit (sold separately).
Indication of the Projection Image Size and Projection Distance
For details, refer to “Screen Size and Projection Distance” on page 18.
Example : When using a wide screen (16:9)
Picture Size
500" (1270 cm)
436
"
×
245
(1107 cm
"
200" (508 cm)
×
623
174"
cm )
×
98"
(443 cm
100" (254 cm)
80" (203 cm)
40" (102 cm)
87"
×
249 cm)
×
49"
(221 cm
70"
Projection
Distance
×
×
39"
125 cm)
100 cm)
(177 cm
35"
×
×
20"
×
(89 c
m
50 cm)
4'1" ~ 4'9"
(1.3 m ~ 1.4 m)
8'3" ~ 9'6"
(2.5 m ~ 2.9 m)
-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector (Continued)
Screen Size and Projection Distance
When using a wide screen (16:9): In case of displaying the 16:9 picture on the whole of the 16:9 screen.
Picture (Screen) size
Width
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center to
the bottom of the image [H]
Diag. (x)
500"
Height
245"
196"
147"
123"
98"
74"
59"
49"
39"
(1270 cm)
(1016 cm)
(762 cm)
(635 cm)
(508 cm)
(381 cm)
(305 cm)
(254 cm)
(203 cm)
(152 cm)
(102 cm)
436"
349"
261"
218"
174"
131"
105"
87"
(1107 cm)
(886 cm)
(664 cm)
(553 cm)
(443 cm)
(332 cm)
(266 cm)
(221 cm)
(177 cm)
(133 cm)
(89 cm)
(623 cm)
(498 cm)
(374 cm)
(311 cm)
(249 cm)
(187 cm)
(149 cm)
(125 cm)
(100 cm)
(75 cm)
51'6"
41'2"
30'11"
25'9"
20'7"
15'5"
12'4"
10'4"
8'3"
(15.7 m)
(12.6 m)
(9.4 m)
(7.9 m)
(6.3 m)
(4.7 m)
(3.8 m)
(3.1 m)
(2.5 m)
(1.9 m)
(1.3 m)
39 3/8"
31 1/2"
23 5/8"
(100 cm)
(80 cm)
(60 cm)
(50 cm)
(40 cm)
(30 cm)
(24 cm)
(20 cm)
(16 cm)
(12 cm)
(8 cm)
—
400"
300"
250"
200"
150"
120"
100"
80"
47'6"
35'8"
29'8"
23'9"
17'10"
14'3"
11'11"
9'6"
(14.5 m)
(10.9 m)
(9.1 m)
(7.2 m)
(5.4 m)
(4.3 m)
(3.6 m)
(2.9 m)
(2.2 m)
(1.4 m)
19 11
/
"
16
15 3/4"
11 13
9 29
/
/
"
"
16
64
7 7/8"
70"
52"
6 19
4 23
3 5
/
/
/
"
64
"
32
"
32
60"
40"
29"
6'2"
7'2"
35"
20"
(50 cm)
4'1"
4'9"
x
: Picture (Screen) diagonal size: 40
L : Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H : Distance from the lens center to the bottom of the image (in/cm)
"
– 500"
The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1(m) = 0.0314
L2(m) = 0.0362
L1(ft) = 0.0314
L2(ft) = 0.0362
x
x
/ 0.3048
/ 0.3048
x
x
H (in) = 0.2
x
/ 2.54
H (cm) = 0.2
x
When using a normal screen (4:3): In case of displaying the 4:3 picture on the whole of the 4:3 screen.
Picture (Screen) size
Width
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center to
the bottom of the image [H]
Diag. (x)
400"
Height
240"
180"
150"
120"
90"
72"
60"
48"
42"
(1016 cm)
(762 cm)
(635 cm)
(508 cm)
(381 cm)
(305 cm)
(254 cm)
(203 cm)
(178 cm)
(152 cm)
(102 cm)
320"
240"
200"
160"
120"
96"
(813 cm)
(610 cm)
(508 cm)
(406 cm)
(305 cm)
(244 cm)
(203 cm)
(163 cm)
(142 cm)
(122 cm)
(81 cm)
(610 cm)
(457 cm)
(381 cm)
(305 cm)
(229 cm)
(183 cm)
(152 cm)
(122 cm)
(107 cm)
(91 cm)
50'5"
37'10"
31'6"
25'3"
18'11"
15'2"
12'7"
10'1"
8'10"
7'7"
(15.4 m)
(11.5 m)
(9.6 m)
(7.7 m)
(5.8 m)
(4.6 m)
(3.8 m)
(3.1 m)
(2.7 m)
(2.3 m)
(1.5 m)
38 35
/
/
"
"
(98 cm)
(73 cm)
(61 cm)
(49 cm)
(37 cm)
(29 cm)
(24 cm)
(20 cm)
(17 cm)
(15 cm)
(10 cm)
—
64
300"
250"
200"
150"
120"
100"
80"
70"
60"
40"
43'7"
36'4"
29'1"
21'10"
17'5"
14'6"
11'8"
10'2"
8'9"
(13.3 m)
28 29
32
(11.1 m)
(8.9 m)
(6.6 m)
(5.3 m)
(4.4 m)
(3.5 m)
(3.1 m)
(2.7 m)
(1.8 m)
24 3/32"
19 17
14 29
11 9
9 41
/
/
/
/
/
"
"
"
"
"
64
64
16
64
64
80"
64"
7 45
56"
48"
6 3/4"
36"
5 25
3 55
/
/
"
"
32
32"
24"
(61 cm)
5'1"
5'10"
64
The formula for picture size and projection distance
x
: Picture (Screen) diagonal size: 40
L : Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H : Distance from the lens center to the bottom of the image (in/cm)
"
– 400"
[Feet/inches]
[m/cm]
L1(m) = 0.03843
L1(ft) = 0.03843
x
/ 0.3048
/ 0.3048
/ 2.54
x
x
L2(ft) = 0.0443
x
L2(m) = 0.0443
H (cm) = 0.24477
x
H (in) = 0.24477
x
When using a normal screen (4:3): In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen.
Screen size
Width
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center to
the bottom of the image [H]
Diag. (x)
500"
Height
300"
(1270 cm)
(1016 cm)
(762 cm)
(635 cm)
(508 cm)
(381 cm)
(305 cm)
(254 cm)
(203 cm)
(178 cm)
(152 cm)
(102 cm)
400"
(1016 cm)
(813 cm)
(610 cm)
(508 cm)
(406 cm)
(305 cm)
(244 cm)
(203 cm)
(163 cm)
(142 cm)
(122 cm)
(81 cm)
(762 cm)
(610 cm)
(457 cm)
(381 cm)
(305 cm)
(229 cm)
(183 cm)
(152 cm)
(122 cm)
(107 cm)
(91 cm)
47'3"
37'10"
28'4"
23'8"
18'11"
14'2"
11'4"
9'5"
(14.4 m)
(11.5 m)
(8.6 m)
(7.2 m)
(5.8 m)
(4.3 m)
(3.5 m)
(2.9 m)
(2.3 m)
(2.0 m)
(1.7 m)
(1.2 m)
36 9/64"
(92 cm)
(73 cm)
(55 cm)
(46 cm)
(37 cm)
(28 cm)
(22 cm)
(18 cm)
(15 cm)
(13 cm)
(11 cm)
(7 cm)
—
400"
300"
250"
200"
150"
120"
100"
80"
320"
240"
200"
160"
120"
96"
240"
180"
150"
120"
90"
72"
60"
48"
42"
43'7"
32'8"
27'3"
21'10"
16'4"
13'1"
10'11"
8'9"
(13.3 m)
28 29
21 11
/
/
"
"
32
(10.0 m)
(8.3 m)
(6.6 m)
(5.0 m)
(4.0 m)
(3.3 m)
(2.7 m)
(2.3 m)
(2.0 m)
(1.3 m)
16
18 1/16"
14 29
10 27
8 43
/
/
/
/
/
"
"
"
"
"
"
"
"
64
32
64
64
32
80"
64"
7 15
7'7"
5 25
70"
60"
40"
56"
48"
32"
6'7"
7'8"
5 1/16
36"
5'8"
6'6"
4 11
2 57
/
/
32
24"
(61 cm)
3'9"
4'4"
64
x
: Screen diagonal size: 40
"
– 500"
The formula for screen size and projection distance
L : Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
[Feet/inches]
[m/cm]
L1(ft) = 0.02882
L2(ft) = 0.03323
H (in) = 0.18358
x
x
x
/ 0.3048
/ 0.3048
/ 2.54
L1(m) = 0.02882
L2(m) = 0.03323
H (cm) = 0.18358
x
x
x
H : Distance from the lens center to the bottom of the image (in/cm)
Note
• Refer to page 16 concerning “Projection distance [L]” and “Distance from the lens center to the bottom of
the image [H]”.
• Allow a margin of error in the value in the diagrams above.
-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Samples of Cables for Connection
•For more details of connection and cables, refer to the operation manual of the connecting equipment.
•You may need other cables or connectors not listed below.
Terminal on
connected
equipment
Terminal on the
Equipment
Cable
projector
Video equipment
HDMI output HDMI cable (commercially available)
terminal
HDMI1, 2
(
Page 20)
Component Component cable (commercially available)
COMPONENT
video output
terminal
3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)
COMPUTER/
COMPONENT
S-video
S-video cable (commercially available)
S-VIDEO
output terminal
(
Page 20)
Video output Video cable (commercially available)
terminal
VIDEO
Camera/Video game Component Cables for a camera or a video game/3 RCA to mini COMPUTER/
video
output
terminal
D-sub 15 pin cable (optional, AN-C3CP2)
COMPONENT
RCA adaptor plug
(commercially available)
S-video
output
Cables for a camera or a video game
Cables for a camera or a video game
RGB cable (commercially available)
S-VIDEO
VIDEO
terminal
Video
output
terminal
Computer
RGB
output
terminal
COMPUTER/
COMPONENT
(
Page 21)
HDMI output HDMI cable (commercially available)
terminal
HDMI1, 2
-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices
to be connected. After making all connections, turn on the projector and then the other devices.
Connecting Equipment with HDMI Output Terminal to the HDMI Terminal on the Projector
For video connection, use a cable that conforms to HDMI standards. Using cables that do not conform to HDMI
standards may result in a malfunction.
HDMI-compatible device
To HDMI output terminal
To HDMI1 or 2 terminal
HDMI cable (type A)
(commercially available)
Note
•Depending on specifications of equipment or the DVIÙHDMI digital cable, the signal transmission may
not work property. (The HDMI specification does not support all connections to equipment that has digital
output terminal using a DVIÙHDMI digital cable.)
•HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition video
signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
•Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital
video signal does not degrade when transmitted, and a high-quality image with a simple connection can
be enjoyed.
Connecting to Equipment with S-video Output Terminal
DVD Player, etc.
To S-VIDEO terminal
To S-video output terminal
S-video cable
(commercially available)
Refer to “Samples of Cables for Connection” on page 19 for connecting other equipment.
-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
Ensure that the computer is the last device to be turned on after all the connections are made.
Connecting to a Computer Using the RGB Cable
Computer
To COMPUTER/COMPONENT terminal
To RGB output terminal
RGB cable
(commercially available)
Note
• Refer to “Compatibility Chart” on page 70 for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may cause some of the functions not to work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s
external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a
SHARP notebook computer). Refer to the specific instructions in your computer’s operation manual to
enable your computer’s external output port.
-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control
the projector and check the status of the projector.
When connecting to a computer using an RS-232C serial control cable
Computer
To RS-232C terminal
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• For details on RS-232C specifications and commands, see page 66.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may
damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
•The power indicator illuminates red, and the
projector enters standby mode.
Power cord
(supplied)
Info
Turning the Projector On
•English is the factory default language. If you
want to change the on-screen display to another
language, change the language according to the
procedure on page 45.
Note that the connections to external equipment and
power outlet should be done before performing the
operations written below. (See pages 20 to 23.)
Power indicator
Open the lens shutter fully and press
STANDBY/ON on the projector or ON
on the remote control.
•The power indicator illuminates green.
•After the lamp indicator illuminates, the projec-
tor is ready to start operation.
STANDBY/ON button
•When the lens shutter is closed, the power
indicator blinks alternately green and orange
and the projector does not turn on.
Lamp indicator
Note
•About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green:The lamp is warming up.
Red: The lamp is shut down abnormal-
ly or the lamp should be replaced.
•When switching on the projector, a slight
flickering of the image may be experienced
within the first minute after the lamp has
been illuminated. This is normal operation as
the lamp's control circuitry is stabilizing the
lamp output characteristics. It should not be
regarded as faulty operation.
Lens shutter
STANDBY button
ON button
•If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to start projection.
On-screen display
Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector or
STANDBY on the remote control, then
press that button again while the confir-
mation message is displayed, to put the
projector into standby mode.
Info
•Direct Power Off function:
You can unplug the power cord from the AC outlet
even if the cooling fan is still running.
•
The projector cannot be turned on while cooling.
-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Adjusting the Projected
Image
Zoom ring
Focus ring
1 Adjusting the Focus
You can adjust the focus with the focus ring
on the projector.
Rotate the focus ring to adjust the
focus while watching the projected
image.
2 Adjusting the Picture Size
You can adjust the picture size using the
zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the picture size.
3 Adjusting the Height
The height of the projector can be adjusted
using the adjustment feet.
When the screen is above the projector, the
projection image can be made higher by
adjusting the projector.
HEIGHT ADJUST lever
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
Remove your hands from the
HEIGHT ADJUST lever of the
projector after its height has
Make small
adjustments.
been finely adjusted.
•The angle of projection is adjustable up
to 9 degrees from the surface on which
the projector is placed.
Info
•Do not apply too much pressure on the projector
when the front adjustment feet come out.
•When lowering the projector, be careful not to get
your fingers caught in the area between the adjust-
ment feet and the projector.
Note
•When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the
procedures in Keystone Correction to correct
the distortion. (See pages 25 and 44.)
•Hold the projector firmly while lifting or carrying.
•Do not hold by the lens area.
-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Keystone Correction
This function can correct distortion of an image
projected toward a spherical or cylindrical screen
as well as trapezoidal distortion of an image on a
flat screen and rotate the image at your arbitrary
angle.
KEYSTONE button
ENTER button
Keystone
When the image is projected either from the top or
from the bottom towards the screen at an angle, the
image becomes distorted trapezoidally. The
function for correcting trapezoidal distortion is
called Keystone Correction.
Adjustment buttons
(P/R/O/Q)
RETURN button
Note
•The Keystone Correction can be adjusted up
to an angle of approximately 40 degrees
with “V-Keystone” and approximately 30
degrees with “H-Keystone”.
For horizontal keystone correction
For vertical keystone correction
O, Qbutton
P, Rbutton
Press KEYSTONE to enter the
keystone mode.
•The keystone mode list appears.
Keystone Correction
H-Keystone Correction:
KEYSTONE MODE
KEYSTONE
SPHERE
ROTATION
SEL.
ENTER
END
V-Keystone Correction:
Press P/Rto select “KEYSTONE”,
and then press ENTER.
•The keystone menu guide appears.
H: 0
V: 0
KEYSTONE
END
ADJUST
TESTPATTERN
RESET
Note
Selectable buttons
Description
•To return to the default setting, press RETURN
while the on-screen display of the Keystone
mode is on the screen.
Exits the keystone mode.
KEYSTONE
END
ADJUST
Adjusts the keystone correction.
Displays the testpattern.
P/R/O/Q
TESTPATTERN
ENTER
Returns to a default setting.
RESETRETURN
Info
•While adjusting the image using Keystone/
Sphere/Rotation Correction, straight lines
and the edges of the image may appear
jagged.
Press P/R/O/Q to adjust the
Keystone Correction.
Press KEYSTONE.
•The on-screen display of the Keystone
mode will disappear.
-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Sphere
Rotation
This function can correct distortion of an image
projected toward a spherical or cylindrical screen.
This function rotates the image at an arbitrary angle.
Press KEYSTONE to enter the
keystone mode.
•The keystone mode list appears. (See
page 25.)
Press KEYSTONE to enter the
keystone mode.
•The keystone mode list appears. (See
page 25.)
PressP/Rtoselect“ROTATION”,
and then press ENTER.
•The rotation menu guide appears.
Press P/Rto select “SPHERE”,
and then press ENTER.
•The sphere menu guide appears.
Selectable items
RETURN
Description
Selectable items
RETURN
Description
Returns to the keystone mode list.
Adjusts the rotation correction.
Displays the testpattern.
Returns to the keystone mode list.
Adjusts the sphere correction.
Displays the testpattern.
ADJUST
ADJUST
TESTPATTERN
RESET
TESTPATTERN
RESET
Returns to a default setting.
Returns to a default setting.
Press P/R/O/Q to adjust the
Rotation Correction mode.
Press P/R/O/Q to adjust the
Sphere Correction mode.
3
Rotates the image clockwise.
Rotates the image counterclockwise.
P, Qbutton
R, Obutton
For correction of concave distortion
For correction of convex distortion
P, Qbutton
R, Obutton
Rotation Correction
Sphere Correction
Correction of Concave Distortion:
Correction of Convex Distortion:
Note
•
To return to the default setting, press RETURN
while the on-screen display of the Keystone
mode is on the screen.
Press KEYSTONE.
•The on-screen display of the Rotation
Correction mode will disappear.
Note
•
To return to the default setting, press RETURN
while the on-screen display of the Keystone
mode is on the screen.
Press KEYSTONE.
•The on-screen display of the Sphere
Correction mode will disappear.
-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the Input Mode
HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO, COMPUTER
buttons
Select the appropriate input mode for the connected
equipment.
Press HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO or COMPUTER on the
remote control to select the input mode.
•When you press INPUT on the projector or on
the remote control, the INPUT list appears.
Press P/Rto switch the INPUT mode.
IMAGE SHIFT button
Adjustment buttons
(P/R/O/Q)
INPUT list
INPUT
INPUT button
HDMI1
HDMI2
Press P/R/O/Q to adjust the
vertical and horizontal position
of the image.
COMPONENT
COMPUTER
S-VIDEO
VIDEO
H-Image Shift
Selectable items
\ button
| button
H-Image Shift
Leftward
Rightward
Note
•
•
When you switch the INPUT mode, the image as
shown below will be displayed in the upper right
corner of the screen. (You can confirm the selected
input mode and information on the input signal.)
\ button
| button
HDMI1
YPbPr
1080P
When
is displayed, “3D” is set to “On”.
•If
is displayed, it means that a 3D image
V-Image Shift
Selectable items
signal that can be automatically detected is
being input.
" button
' button
V-Image Shift
Downward
Upward
Adjusting the Vertical and
Horizontal Position of the
Image
" button
' button
Press IMAGE SHIFTto enter the
image shift mode.
•The image shift menu guide appears.
Note
H: 0
V: 0
IMAGE SHIFT
END
•To return to the default setting, press
RETURN when the image shift menu guide
is still on the screen.
ADJUST
RESET
•The adjustable range of the image shift may
vary depending on:
Selectable buttons
Description
- the Resize mode
- the Picture mode
- the input signal resolution
- the input 3D signal type
Exits the image shift mode.
END
ADJUST
RESET
IMAGE SHIFT
Adjusts the image shift.
P/R/O/Q
Returns to a default setting.
RETURN
-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Displaying the Black Screen
Temporarily
FREEZE button
AUTO SYNC button
PICTURE MODE button
Close the lens shutter to temporarily display a black
screen.
Note
•When you close the lens shutter, the projector
will be turned off automatically after about 30
minutes.
Freezing a Moving Image
Press FREEZE.
•The projected image is frozen.
Press FREEZE again to return to
the moving image from the cur-
rently connected device.
Auto Sync
(Auto Sync Adjustment)
Selecting the Picture Mode
You can select the appropriate picture mode for the
projected image, such as movie or video game.
Auto Sync function works when detecting input signal
after the projector turns on.
Press PICTURE MODE.
•When pressing PICTURE MODE, the picture mode
changes in the following order:
Press AUTO SYNC to manually adjust with
Auto Sync function.
Standard
Natural
Dynamic
Note
Game
Movie2
Movie1
•When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjust-
ments. (See page 41.)
Note
•See page 37 for details on the picture mode.
-28
Download from Www.Somanuals.com. All Manuals Search And Download.
MAGNIFY buttons
IRIS 1, 2 buttons
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of projected images
can be enlarged. This is helpful when providing more
detailed explanations.
Adjustment buttons
(P/R/O/Q)
RETURN button
Press
control.
•Enlarges the image.
MAGNIFY on the remote
MENU HIDE button
ECO+QUIET button
•Pressing
or
MAGNIFY enlarges or
reduces the projected image.
Note
Switching the Iris Setting
Press
.
This function controls the quantity of the projected
light and the contrast of the image.
×1 ×2 ×3 ×4 ×9
Press
.
Press IRIS 1 or 2.
•You can change the location of the en-
larged image using P, R, Oand Q.
•Each time the button is pressed while the display is
on, the mode changes in the following order:
IRIS 1 High Brightness
IRIS 2
High Contrast
On
Off
Press RETURN on the remote con-
trol to cancel the operation.
•To return to the default setting (×1), press
RETURN when the on-screen display of the
magnify mode is displayed.
Note
•For details, see page 38.
Note
Hiding the Menu Temporarily
(Menu Hide)
•The selectable magnifications differ de-
pending on the input signal.
•This function is not available for the 3D
mode.
•In the following cases, the image will return
to the normal size (×1).
- When switching the INPUT mode.
- When RETURN has been pressed while
the on-screen display of the magnify
mode is displayed.
When the menu screen is displayed, you can tempo-
rarily hide the menu screen by pressing and holding
MENU HIDE on the remote control. This is useful
when, for example, checking the video adjustment
information.
- When the input signal is changed.
- When the input signal resolution and re-
fresh rate (vertical frequency) change.
- When the Resize mode is changed.
- When the Picture mode is changed.
- When switching between 2D and 3D
mode.
Switching the Eco+Quiet Mode
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
•When the Eco+Quiet Mode is set to “On”, the sound of
the cooling fan will turn down, the power consumption
will decrease, and the lamp life will extend.
Note
•Refer to “Eco+Quiet” on page 38 for details.
-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
RESIZE button
Resize Mode
This function allows you to modify or customize the
resize mode to enhance the input image.
Press RESIZE on the projector or on the
remote control.
Note
•The RESIZE function that can be selected
varies depending on the input signal
(resolution and vertical frequency).
RESIZE button
Resize Mode
RESIZE
Output screen image
NORMAL
The image is displayed with the original aspect ratio.
16:9
An image compressed from a 16:9 aspect ratio to a 4:3 aspect ratio
is restored to a 16:9 aspect ratio and displayed at full-screen.
CINEMA ZOOM
A CinemaScope image or an image with a 16:9 aspect ratio is
displayed at full-screen
-30
Download from Www.Somanuals.com. All Manuals Search And Download.
RESIZE
Output screen image
ZOOM 14:9
An image with a 14:9 aspect ratio and letterboxing is enlarged while
maintaining the original aspect ratio.
SMART ZOOM
An image with a 4:3 aspect ratio is slightly enlarged.
NATIVE
The image is displayed according to the original input signal.
About Copyrights
•When using the RESIZE function to select an image size with a different aspect ratio to a TV program or
video image, the image will look different from its original appearance. Keep this in mind while choosing an
image size.
•The use of the RESIZE or Overscan function to compress or stretch the image for commercial purposes/public
displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders.
Please use caution.
-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bar Items
The following shows the items that can be set in the projector.
The selectable items vary depending on the selected input, input signals, or adjustment
values. Items that cannot be selected will be grayed out.
“Picture” menu
Main menu
Sub menu
Picture
Picture Mode
Standard
Natural
Dynamic
Movie1
Movie2
Game
Page 37
Page 37
Contrast –30 +30
Bright –30 +30
Color
Tint
–30 +30
–30 +30
Sharp –30 +30
Red
–30 +30
–30 +30
Blue
–2 +2
CLR Temp
Page 37
IRIS1 (Manual)
High Brightness
High Contrast
Page 38
IRIS2 (Auto)
Page 38
Eco+Quiet
Page 38
Advanced
Page 38
Reset
On
Off
On
Off
Gamma
Page 38
C.M.S.1
Page 38
–2 +2
Select Color
Hue
Page 40
Saturation
Value
Effect
C.M.S.1
Reset
On
Off
Return
Select Color
Hue
C.M.S.2
Page 38
Saturation
Value
Effect
C.M.S.2
Reset
On
Off
Return
Bright Boost
Page 40
On
Off
Film Mode
Page 40
Auto
Off
Detail Enhance
–30 +30
Page 40
DNR
Page 40
MNR
Page 40
Off
Level 1
Level 2
Level 3
-32
Download from Www.Somanuals.com. All Manuals Search And Download.
“SIG-ADJ” menu
“SCR-ADJ” menu
Main menu
Sub menu
Main menu
Sub menu
SIG-ADJ
Clock –150 +150
SCR-ADJ
Resize
Page 41
Page 41
Page 43
Page 43
Phase –30 +30
Page 41
H-Image Shift
Page 43
V-Image Shift
Page 43
Overscan
Page 43
–
30
30
+30
+30
H-Pos –150 +150
Page 41
–
On
Off
V-Pos –60 +60
Page 41
Auto V-Keystone
Page 44
Keystone Mode
Page 44
Reset
Resolution
Page 41
Keystone
Sphere
Rotation
Auto Sync
On
Off
H-Keystone
–60
+60
Page 41
Page 44
V-Keystone –80 +80
Signal Type
Auto
RGB
Page 41
YPbPr
Page 44
Sphere
Page 44
Rotation
Page 45
OSD Display
Page 45
–30 +30
Video System
Auto
PAL
Page 42
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
–50 +50
On
Off
PAL-60
OSD Brightness
Page 45
Standard
Level 1
Level 2
Video Setup
Page 42
0 IRE
7.5 IRE
Dynamic Range
Page 42
Auto
Standard
Enhanced
Background
Logo
Blue
Page 45
None
Signal Info :
Page 42
Menu Position
Center
Upper Right
Lower Right
Upper Left
Lower Left
Page 45
PRJ Mode
Front
Ceiling + Front
Rear
Ceiling + Rear
Page 45
Language
English
polski
Magyar
Türkçe
Deutsch
Español
Nederlands
Français
Italiano
Page 45
Svenska
Português
-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bar Items (Continued)
“PRJ-ADJ” menu
“3D MENU”
Main menu
PRJ-ADJ
Sub menu
Auto Power Off
Main menu
3D MENU
Sub menu
3D
On
Off
On
Off
Page 46
Page 55
Page 46
Page 55
Economy Mode
Page 46
On
Off
3D Format
Auto
Side By Side
Top And Bottom
Page 55
One Touch Play
Page 46
On
Off
3D Depth Adjust
–15
+15
Page 55
System Standby
Page 46
On
Off
IR Emitter Level
Normal
High
Page 55
Input Name
Page 47
3D Auto Change
Yes
No
Page 55
Demo Mode
Page 47
On
Off
Viewing Time Info
Page 55
Yes
No
RS-232C
9600bps
38400bps
115200bps
Invert
Page 47
Page 55
Fan Mode
Page 47
Normal
High
All Reset
Page 47
Lamp Timer (Life)
Page 47
-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
Adjustment buttons
('/"/\/|)
MENU button
ENTER button
Adjustment buttons
('/"/\/|)
ENTER button
RETURN button
MENU button
RETURN button
• Press RETURN
to return to the
previous screen
when the menu is
displayed.
Menu Selections (Adjust-
ments)
• This operation can also be performed by using
the buttons on the projector.
Example: “Picture” menu screen when
COMPONENT is selected for
input mode
Press MENU.
• The “Picture” menu screen for the se-
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Menu bar
Standard
lected input mode is displayed.
0
0
0
0
0
0
0
0
Color
Tint
Sharp
Red
Press | or \ to select the menu
screen to adjust on the menu
bar.
Blue
CLR Temp
IRIS1 (Manual)
High Brightness
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
On
Off
SEL./ADJ.
RETURN
ENTER
END
-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen (Continued)
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Press ' or " to select the item
you want to adjust.
(Example: Selecting “Bright”)
3
Standard
0
0
0
0
0
0
0
0
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
To adjust the projected
image while viewing it
High Brightness
On
Off
Single-
adjustment
item
Press ENTER.
• The selected adjustment item (e.g.
“Bright”) will be displayed at the bottom
of the screen.
• When ' or " is pressed, the next
item will be displayed. (e.g. “Bright” is
replaced with “Color” by pressing ".)
SEL./ADJ.
RETURN
ENTER
END
Bright
0
Note
• Press RETURN to return to the previ-
ous screen.
Press | or \ to adjust the item
selected.
• The adjustment is stored.
• For some menu items, press | to dis-
play its submenu and press ' or "
to select an adjustment item, and then
press ENTER.
Press MENU.
• The menu screen will disappear.
-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
Menu operation ⇒ Page 35
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Standard
0
0
0
0
0
0
0
0
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
IRIS2 (Auto)
Eco+Quiet
Advanced
Gamma
0
0
C.M.S.1
C.M.S.2
Bright Boost
Film Mode
On
Off
Off
High Brightness
On
Off
Auto
Detail Enhance
Off
Off
DNR
MNR
Reset
SEL./ADJ.
RETURN
ENTER
END
SEL./ADJ.
RETURN
ENTER
END
1Selecting the Picture Mode
This function allows you to select the picture mode that best suits the room brightness and the type of image being
projected.
The main default settings of each item when selecting Picture Mode
Selectable
items
Description
IRIS1
CLR Temp Bright Boost
IRIS2 (Auto) Eco+Quiet
(Manual)
Standard
Natural
Dynamic
Movie1
For standard image
A balanced color image is obtained.
A vivid image is obtained.
For viewing images with the brightness
slightly toned down in a darkened
room
0
0
0
Off
Off
On
Off
High Brightness
High Brightness
High Brightness
High Contrast
On
Off
Off
Off
Off
Off
Off
On
-1
Movie2
Game
For viewing images with the brightness
slightly boosted in a darkened room
Use this when the audio and image
are not synched or when you want to
create a sharper image.
-1
0
Off
On
High Contrast
High Brightness
On
Off
On
Off
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.
Note
•You can also press PICTURE MODE on the remote control to select the picture mode. (See page 28.)
•The default settings are subject to change without notice.
2Adjusting the Image
Adjustment items
\ button
For less contrast.
| button
For more contrast.
Contrast
Bright
Color
For less brightness.
For less color intensity.
For more brightness.
For more color intensity.
Tint
Sharp
Red
For making skin tones purplish.
For less sharpness.
For making images less reddish.
For making images less bluish.
For making skin tones greenish.
For more sharpness.
For making images more reddish.
For making images more bluish.
Blue
CLR Temp
For making images slightly more reddish For making images slightly more bluish
(slightly warmer colors). (slightly cooler colors).
-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu) (Continued)
Menu operation ⇒ Page 35
Correcting Gradation of Video (Gamma Correction)
6
3Switching the Iris Setting
This function controls the quantity of the projected light
and the contrast of the image.
IRIS1 (Manual)
When the darker areas of the image become difficult to
see because of the image or the projection environment,
you can correct the gamma setting to make the image
brighter and easier to see.
Selectable items
Description
Selectable items
Description
Provides a brighter gradation.
Standard setting
High Brightness
This mode gives priority to brightness
over contrast.
This mode gives priority to contrast
over brightness.
+2
+1
0
High Contrast
–1
–2
IRIS2 (Auto)
This automatically selects the optimal contrast to match
the image.
Provides a darker gradation.
Selectable items
On
Description
This mode gives priority to contrast
with the use of auto adjustment.
7Adjusting the Colors
You can select the color of the projected image to correct
and then adjust it to the desired color by setting “Hue”,
“Saturation”, “Value”, and “Effect”.
Off
This mode gives priority to brightness
without the use of auto adjustment.
Note
Note
•You can also use IRIS 1, 2 on the remote con-
trol to change the Iris. (See page 29.)
•Before performing this adjustment, prepare the
image to be adjusted.
•You can perform this adjustment easier in the
still image than in the moving image.
4Eco+Quiet
Select “C.M.S.1” or “C.M.S.2”
(C.M.S.: Color Management Sys-
tem) in the “Advanced” menu, and
press ENTER.
•If there is no data for the stored corrected
color, the color selection screen and the
picker is displayed. (Go to step 2.)
Selectable items Brightness and Power consumption
On
Off
Approx. 75%
100%
Note
•When “Eco+Quiet” is set to “On”, the power
consumption will decrease and the lamp life
will extend. (Projection brightness decreases
approximately 25%.)
Picker
5Using the Advanced
“Advanced” allows you to make even finer adjustments
to the image so that it appears just the way you want
it to.
To display the Advanced menu, select “Advanced” and
press ENTER.
Note
•When the “Advanced” settings are displayed,
select “Advanced” again and press ENTER to
return to the “Picture” menu.
-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation ⇒ Page 35
Set or adjust each item in the C.M.S.
color adjustment screen.
•If there is data for the stored corrected
color, the C.M.S. color adjustment screen
is displayed. (Go to step 3.)
3
C.M.S.1
Select Color
Hue
Saturation
Value
0
0
0
0
C.M.S.1
Select Color
Effect
Hue
Saturation
Value
0
0
0
0
C.M.S.1
Reset
Return
On
Effect
C.M.S.1
Reset
On
Return
SEL./ADJ.
RETURN
ENTER
END
SEL./ADJ.
RETURN
ENTER
END
C.M.S. color adjustment screen:
Selectable items
Description
Select Color
Starts over the selection of the
color to be corrected.
Use the picker and select the color
of the projected image to correct.
The picker can be operated by ad-
justment buttons (P/R/O/Q) on the
Hue
Sets the hue of the main colors.
Saturation
Sets the saturation of the main
colors.
remote control.
Value
Effect*1
C.M.S.1*2
(or C.M.S.2)
Sets the value of the main colors.
Specifies the range of color correction.
•By enlarging the projected image using
or
MAGNIFY, more fine adjustment can
Checks the appearance of the
projected image after above
correction.
be performed.
Reset
Sets “Hue”, “Saturation”, “Value”,
and “Effect” to their default values.
Picker
Return
Completes the correction and closes
the C.M.S. color adjustment screen.
*1 To specify the range of color correction, select
“Effect” and press Oor Qbutton.
Obutton
Specifies smaller range.
Specifies larger range.
Qbutton
*2 To check the appearance of the projected image,
select “C.M.S.1” (or “C.M.S.2”) and set to “On”
or “Off”.
•By continuing to press the adjustment
buttons (P/R/O/Q), the picker moves
rapidly.
On
The appearance of the projected
image after above color adjustment
reflected can be checked.
After selecting the color of the projected
image to correct, press ENTER. The
C.M.S. color adjustment screen is
displayed. (Go to step 3.)
Off
The appearance of the projected
image in former color adjustment
can be checked.
To complete the C.M.S. color
adjustment, select “Return” and
press ENTER.
Note
•The C.M.S. color adjustment can be made to
one color each in “C.M.S.1” and “C.M.S.2”.
-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu) (Continued)
Menu operation ⇒ Page 35
8Adjusting the Bright Boost
wMosquito Noise Reduction (MNR)
Bright Boost uses Texas Instruments’ Bright Boost
technology. The image becomes brighter while the color
reproduction is kept at a high level.
The so-called Mosquito Noise (flickering) can be
reduced.
Selectable items
Off
Description
Selectable items
On
Off
Description
MNR does not function.
The Bright Boost function is activated.
The Bright Boost function is not activated.
Level 1
Level 2
Level 3
Sets the MNR level for viewing a clear-
er picture.
9Selecting the Film Mode
This function provides high-quality playback of
images originally projected at 24 fps, such as movies
on DVDs.
Note
•Set “MNR” to “Off” in the following cases:
- When the image is blurry.
-
When the contours and colors of moving
images drag.
Selectable items
Description
Films are detected automatically.
Films are not detected.
Auto
Off
- When TV broadcasts with weak signals are
projected.
•This function is available for the following
signals.
With S-VIDEO or VIDEO input:
- 480I/480P
0Setting Detail Enhancement
This function enhances the details in images and,
thereby, creates a greater sense of depth.
- 576I/576P
Provides less detail enhancement.
Provides more detail enhancement.
\ button
| button
eResetting All Adjustment Items
To reset all adjustment items to the default settings,
select “Reset” and press ENTER.
ｑReducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high quality
images with minimal dot crawl and cross color noise.
Selectable items
Off
Description
The DNR function is not activated.
Level 1
Level 2
Level 3
Sets the DNR level for viewing a clear-
er picture.
Note
•Set “DNR” to “Off” in the following cases:
- When the image is blurry.
-
When the contours and colors of moving
images drag.
- When TV broadcasts with weak signals are
projected.
•This function is available for the following
signals.
With S-VIDEO or VIDEO input:
- 480I/480P
- 576I/576P
-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustment (“SIG-ADJ” Menu)
Menu operation ⇒ Page 35
The illustration shown here is for explanation and may
be different from the actual on-screen display.
Note
Picture
Clock
Phase
H-Pos
V-Pos
SCR-ADJ
PRJ-ADJ
SIG-ADJ
•
Avoid displaying computer patterns which repeat
every other line (horizontal stripes). (Flickering
may occur, making the image hard to see.)
•Information on the currently selected input
signal can be confirmed in item 8 on page 42.
0
0
0
0
Reset
Resolution
Auto Sync
On
*1
*2
Signal Type
Video System
Video Setup
Auto
Auto
0 IRE
Auto
3
Auto Sync (Auto Sync Adjustment)
Dynamic Range
Signal Info : 1080P
Selectable items
On
Description
H : XX.X
kHz/
V : XX.X Hz
Auto Sync adjustment will occur when
the projector is turned on or when
the input signals are switched, when
connected to a computer.
SEL./ADJ.
RETURN
ENTER
END
*1 If the input mode is S-VIDEO or VIDEO input, the display
changes to the “Video System” screen.
*2 Displayed when the input mode is HDMI input.
Off
Auto Sync adjustment is not
automatically performed.
1Adjusting the Computer Image
Note
Use the SIG-ADJ function in case of irregularities such as
vertical stripes or flickering in portions of the screen.
•Auto Sync adjustment is also performed by
pressing AUTO SYNC on the remote control.
•When setting “Auto Sync” to “Off”, and if
AUTO SYNC is pressed, Auto Sync will be ex-
ecuted in “On” mode. If the button is pressed
again within one minute, Auto Sync will be
executed in “On” mode.
•The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
Selectable items
Clock
Description
Adjusts vertical noise.
Phase
Adjusts horizontal noise (similar to
tracking on your VCR).
H-Pos
V-Pos
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.
•
When the optimum image cannot be achieved with
Auto Sync adjustment, use manual adjustments.
Note
•You can automatically adjust the computer
image by setting “Auto Sync” in the “SIG-ADJ”
menu to “On”, or pressing AUTO SYNC on the
remote control.
•Depending on the type of input signal, the
adjustment range for each setting may vary or
the adjustment may not be available at all.
•To reset all adjustment items, select “Reset”
and press ENTER.
4Signal Type Setting
When using an input mode of HDMI1, HDMI2, or COM-
PUTER, set the signal type to the corresponding input
signal type (RGB or YPbPr).
Selectable items
Description
Auto
Automatically selects the appropriate
input signal between RGB and YPbPr.
RGB
YPbPr
Set when RGB signals are received.
Set when YPbPr signals are received.
2Setting the Resolution
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected. How-
ever, for some signals, the optimal resolution mode in
“Resolution” in the “SIG-ADJ” menu may need to be
selected to match the computer display mode.
-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustment (“SIG-ADJ” Menu) (Continued)
Menu operation ⇒ Page 35
5Setting the Video System
7Adjusting the Dynamic Range
The video input system mode is factory preset to “Auto”;
however, a clear picture from the connected audio-visual
equipment may not be received, depending on the video
signal difference. In that case, switch the video signal.
An optimum picture may not be displayed if an HDMI-
capable device’s output signal type and the projector’s
input signal type do not match. If this should occur,
switch “Dynamic Range”.
Selectable items
Auto
PAL
Selectable items
Description
Auto
In most circumstances, “Auto” should
be selected.
Standard
Enhanced
When the black levels of the image
show banding or appear faded, select
the item that results in the best picture
quality.
SECAM
*NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
8Signal Info
Input signal information is displayed.
* When reproducing NTSC signals in PAL video equip-
ment.
Note
•The video signal can only be set in VIDEO or
S-VIDEO mode.
• When “Video System” is set to “Auto”, you
may not receive a clear picture due to signal
differences. Should this occur, switch to the
video system of the source signal.
6Setting the Video Setup
Selectable items
0 IRE
7.5 IRE
Description
Sets the black level to 0 IRE.
Sets the black level to 7.5 IRE.
Note
•This function is available for the following
signals.
With COMPONENT or COMPUTER/
COMPONENT input:
- 480I
With S-VIDEO or VIDEO input:
- NTSC3.58
-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu)
Menu operation ⇒ Page 35
The illustration shown here is for explanation and may
be different from the actual on-screen display.
V-Image Shift
Selectable items
\ button
| button
Picture
SCR-ADJ
Normal
PRJ-ADJ
SIG-ADJ
V-Image Shift
Downward
Upward
Resize
H-Image Shift
V-Image Shift
Overscan
0
0
On
Auto V-Keystone
Keystone Mode
H-Keystone
V-Keystone
Sphere
Keystone
0
0
0
0
Rotation
\ button
| button
OSD Display
OSD Brightness
Background
Menu Position
PRJ Mode
On
Standard
Logo
Upper Left
Front
Language
English
SEL./ADJ.
RETURN
ENTER
END
Note
•The adjustable range of the image shift may
vary depending on:
- the Resize mode
1Setting the Resize Mode
- the Picture mode
- the input signal resolution
- the input 3D signal type
Note
•For details of the Resize mode, see page 30.
•You can also press RESIZE on the remote
control to set the resize mode. (See page 30.)
3Adjusting the Overscan
This function allows you to adjust the Overscan area
(display area).
2Adjusting the Image Position
You can move the projected image horizontally or verti-
cally.
Selectable items
Description
The input area is displayed without screen
edges.
The whole input area is displayed.
On
Off
H-Image Shift
Selectable items
\ button
| button
H-Image Shift
Leftward
Rightward
Note
•You can adjust the Overscan area for the fol-
lowing input signals and the RESIZE function.
Input signal:
- 480I/480P
- 540P
- 576I/576P
\ button
| button
- 720P
- 1035I
- 1080I/1080P
RESIZE function:
- NORMAL
- 16:9
- CINEMA ZOOM
- ZOOM 14:9
•If the display area ratio is set too large, noise
may appear at the screen edges. If this hap-
pens, set the display area ratio to a smaller
value.
•Also read “About Copyrights” on page 31.
-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu) (Continued)
Menu operation ⇒ Page 35
Select “Keystone Mode” in the “SCR-ADJ” menu
and press ENTER. Then select a desired item among
“Keystone”, “Sphere”, or “Rotation” and press ENTER.
“Keystone” has been set as a default setting in which
4Auto V-Keystone Correction
Select “Auto V-Keystone” in the “SCR-ADJ” menu and
press ENTER. Vertical keystone correction is performed
you can adjust “H-Keystone” and “V-Keystone”.
automatically.
Keystone
H-Keystone:
Note
Makes the upper and lower
sides parallel.
O or Q
•Pressing ENTER when the on-screen display
of the Auto V-Keystone “On” appears changes
the setting of the Auto V-Keystone to “Off”.
•The Keystone Correction can be adjusted up
to an angle of approximately 12 degrees with
“Auto V-Keystone”.
Horizontal Keystone Correction
•For details of Keystone mode, see page 25.
Auto V-Keystone Correction
V-Keystone:
O or Q
Makes the left and right sides
parallel.
Vertical Keystone Correction
5Keystone Mode Correction
This function can correct distortion of an image projected
toward a spherical or cylindrical screen as well as trap-
ezoidal distortion of an image on a flat screen and rotate
the image at your arbitrary angle.
Sphere
This function corrects screen distortion created during
spherical or cylindrical screen projection.
O button
Narrower at the center
Wider at the center
Note
•For details of Keystone mode, see page 25.
Q button
Sphere Correction
Info
Correction of Convex Distortion:
Correction of Concave Distortion:
•While adjusting the image using Keystone/
Sphere/Rotation Correction, straight lines
and the edges of the image may appear
jagged.
-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation ⇒ Page 35
Rotation
0Reversing/Inverting
This function can rotate the image at an arbitrary
angle.
Projected Images
Rotates the image
O button
This function allows the projector to be used in a wider
range of projection styles by allowing the image to be
inverted to suit the projection environment (location).
counterclockwise.
Q button
Rotate the image clockwise.
Selectable items
Description
Rotation Correction
Front
Normal image (Projected from the
front of the screen)
Ceiling + Front
Inverted image (Projected from the
front of the screen with an inverted
projector)
Rear
Reversed image (Projected from the
rear of the screen or with a mirror)
Ceiling + Rear
Reversed and inverted image (Pro-
jected with a mirror)
6Setting On-screen Display
Selectable items
On
Off
Description
See page 17 for details of Projection (PRJ) Mode.
All on-screen displays are displayed.
INPUT/FREEZE/AUTO SYNC/RESIZE/
PICTURE MODE/ECO+QUIET/
MAGNIFY/3D ON/OFF (3D/2D mode
change) message are not displayed.
qSelecting the On-screen Display
Language
The projector can switch the on-screen display language
among 17 languages.
7Setting the Brightness of the
English
Menu Screen
Deutsch
Español
Nederlands
Français
Italiano
Sets the brightness of the menu screen.
Selectable items
Standard
Description
Standard brightness
Level 1
Darker than the “Standard”
brightness
Svenska
Português
Level 2
Darker than the “Level 1” brightness
polski
Magyar
Türkçe
8
Selecting the Background Image
Selectable items
Description
SHARP logo screen
Blue screen
Logo
Blue
None
— (Black screen)
9Selecting the Menu Screen
Position
Select “Menu Position” in the “SCR-ADJ” menu and the
desired position for the menu screen.
Selectable items
Center
Upper Right
Lower Right
Upper Left
Description
Displayed on the center of the image.
Displayed on the upper right of the image.
Displayed on the lower right of the image.
Displayed on the upper left of the image.
Displayed on the lower left of the image.
Lower Left
-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ” Menu)
Menu operation ⇒ Page 35
The illustration shown here is for explanation and may
be different from the actual on-screen display.
3Setting One Touch Play, System
Standby and Input Name
Picture
SCR-ADJ
On
PRJ-ADJ
SIG-ADJ
Auto Power Off
Economy Mode
One Touch Play
System Standby
Input Name
When a Sharp product equipped with Consumer Elec-
tronics Control (HDMI CEC) is connected to the projector
with an HDMI cable, you can use the linked function with
HDMI CEC (“One Touch Play” and “System Standby”).
Off
Off
Off
Demo Mode
RS-232C
Fan Mode
Off
9600bps
Normal
All Reset
Note
The CEC function may not work with some CEC
devices. (When the projector is connected to a non-
Sharp product, the CEC function may not work.)
Lamp Timer (Life)
X
h
XX min ( XX% )
Setting the One-Touch Playback Function
SEL./ADJ.
RETURN
ENTER
END
(One Touch Play)
One Touch Play turns on the projector and selects the
input automatically when you turn on or begin playback
on connected HDMI-compliant Sharp Video Products.
1Setting Auto Power Off Mode
Selectable items
On
Off
Description
This function automatically switches the projector to
Standby mode if no signals are received for a set period.
This enables One Touch Play.
This disables One Touch Play.
Selectable items
On
Description
When no input signal is detected for
more than 15 minutes, the projector
will automatically enter standby mode.
Note
Off
The Auto Power Off function will be
disabled.
•
When enabling One Touch Play, be sure to enable
the CEC setting on the HDMI-compliant Sharp
Video Products connected to the projector.
The Economy mode is set to “Off” when One
Touch Play is set to “On”.
In the following cases, One Touch Play is not
enabled.
- When playback is paused
- When the screen is turned off (black) after the
lens shutter is closed
•
•
Note
•When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
- When the cooling fan is running (See page
60.)
- When the lamp is warming up (See page 60.)
2Setting the Power Save Mode
Setting the System Standby Function
(Economy Mode)
(System Standby)
When you turn off the projector, the HDMI-compliant
video equipment connected to the projector enters
standby mode.
Economy Mode
Selectable items
On
Off
Description
This enables the Economy mode.
Selectable items
On
Off
Description
You can use the linked functions. RS-
232C can be used to control the pro-
jector in standby mode.
This enables System Standby.
This disables System Standby.
Note
Note
•When enabling System Standby, be sure to
enable the CEC setting on the HDMI-compliant
Sharp Video Products connected to the
projector.
•
Set this function to “Off” when you want to use
RS-232C to control the projector from a computer.
•One Touch Play is set to “Off” when the
Economy mode is set to “On”.
-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation ⇒ Page 35
Setting the Input Terminal Names (Input
5Selecting the Transmission
Name)
Speed (RS-232C)
Set the name of the input terminal (up to 14 alphanu-
merical characters).
Make sure that both the projector and computer are set
for the same baud rate.
Press P/R to select “Input Name”
and then press ENTER.
Selectable items
Description
9600bps
Transmission speed is slow.
Picture
SCR-ADJ
PRJ-ADJ
SIG-ADJ
HDMI1
38400bps
Input name
H D M I 1
115200bps
Transmission speed is rapid.
Reset
Return
6Fan Mode Setting
This function changes the fan rotation speed.
Selectable items
Normal
High
Description
\ or | button
▼ or 、 button
ENTER button
Selects a character column.
Selects a character.
Suitable for normal environments.
Select this when using the projector at
altitudes of approximately 4,900 feet
(1,500 meters) or more.
Sets the input terminal name.
Press P/R to select “Return” and
then press ENTER to return to the
previous screen.
•To return to the previous setting, select
“Reset” and then press ENTER.
• When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
7
Returning to the Default Settings
Use “All Reset” to initialize all the adjustments you have
made to the default settings.
Note
•
When connecting the projector to a Sharp Video
Product with an HDMI cable using an input
mode of HDMI1 or HDMI2 and the linked func-
tion with HDMI CEC (“One Touch Play” or “Sys-
tem Standby”) works normally, the name of the
connected Sharp Video Product is automatically
captured.
Note
The following items cannot be initialized.
•“SIG-ADJ” menu — Resolution
•“SCR-ADJ” menu — Language
•“PRJ-ADJ” menu — Lamp Timer (Life)
•
•
When the input terminal name has been changed
by a user, the changed name is displayed.
To return to the default name, select “Reset”
and press ENTER.
8
Lamp Timer (Life)
You can confirm the cumulative lamp usage time and the
remaining lamp life (percentage).
Lamp usage condition
Remaining lamp life
100% 5%
Approx. 3,000 Approx. 150
hours hours
Approx. 2,000 Approx. 100
hours hours
4
Setting the Demo Mode
“Life”
Operated exclusively with
“Eco+Quiet” set to “On”
Set the Demo Mode to “On” or “Off”.
Selectable items Description
On
Off
Operated exclusively with
“Eco+Quiet” set to “Off”
This enables Demo Mode.
This disables Demo Mode.
Note
•It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
•The lamp life may vary depending on the us-
age condition.
-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying 3D Image Viewing
CAUTION: Before viewing 3D images, please read this section carefully.
You can use special 3D Glasses to watch
3D-supported images on this projector.
You can enjoy 3D images by viewing the video images
through the 3D Glasses supplied with the projector or
through optional 3D glasses sold separately.
To produce 3D images, liquid crystal shutters in the
3D Glasses alternately open and close imperceptibly
fast to exactly match alternating left and right video
images displayed by the projector.
Not all consumers can experience and enjoy 3D im-
ages. Some people suffer from stereo blindness which
prevents them from perceiving the intended depth of
3D entertainment. Also, some people who watch 3D
programming may experience initial feelings of motion
sickness as they adjust to the picture. Others may ex-
perience headaches, eye fatigue or continued motion
sickness. Like a roller coaster, the experience is not for
everyone.
People with a known history of photosensitivity and
people with heart problems or poor health should not
use the 3D Glasses. This can worsen existing health
conditions.
Do not use the 3D Glasses for other purposes (such
as general eyeglasses, sunglasses, or protective
goggles).
Do not use the 3D function or 3D Glasses while walk-
ing or moving around. This may result in injuries due to
running into objects, tripping, and/or falling.
When using the 3D Glasses, take care not to acci-
dentally strike the screen or other people. Viewing 3D
images may cause you to misjudge the distance to the
screen and accidentally strike the screen, resulting in
possible injury.
Precautions on viewing 3D images
When viewing 3D images continuously, be sure to take
a break periodically to prevent eye strain.
Take regular breaks, at least 5 to 15 minutes after
every 30 to 60 minutes of 3D viewing.
* Based on the guidelines issued by the 3D Consor-
tium revised December 10, 2008.
View 3D images at the appropriate distance from the
screen. The recommended distance is three times the
effective height of the picture.
Precautions on using 3D Glasses
The 3D Glasses are precision equipment. Handle them
with care.
Improper use of the 3D Glasses or failure to follow
these instructions can result in eye strain.
If you experience dizziness, nausea, or other discom-
fort while viewing 3D images, immediately discontinue
use of the 3D Glasses. Using the binocular dispar-
ity 3D system of this projector with incompatible 3D
broadcasts or software can make images appear with
a cross talk blur or create overlapping images.
If you are nearsighted or farsighted or have astigma-
tism or a different level of eyesight between the left
and right eyes, you should take the necessary steps,
such as wearing eyeglasses, to correct your eyesight
before viewing 3D images. The 3D Glasses can be
worn over eyeglasses.
Examples of recommended distances
100-inch 16:9 picture: Approx. 12.3 ft (3.8 m)
Viewing should not be done closer than the recom-
mended distance.
Refer to page 18 for details on the diagonal size and
height of the picture.
Maintain an appropriate distance from the screen.
Viewing from too close a distance can strain your
eyes. If you experience eye strain, immediately discon-
tinue viewing.
3D viewing is possible within the range that the 3D
Glasses are able to receive infrared signals reflected
by the screen. However, most 3D images are manu-
factured to be viewed from directly in front of the
screen, so 3D viewing is recommended directly in front
of the screen as much as possible.
The 3D Glasses are only recommended for people
ages 5 and older.
When children are viewing 3D images, be sure a par-
ent or guardian is present. Monitor children viewing 3D
images, and if they show signs of discomfort, immedi-
ately discontinue use of the 3D Glasses.
If you experience any of the following symptoms dur-
ing viewing:
– nausea
– queasiness/dizziness
– headache
– blurry vision or double vision that lasts longer than
few seconds
Do not engage in any potentially hazardous activity
(for example, driving a vehicle) until your symptoms
have completely gone away.
If symptoms persist, discontinue use and do not
resume 3D viewing without discussing your symptoms
with a physician.
-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Be careful of your surroundings when viewing 3D im-
ages. When you view 3D images, objects may appear
at a distance closer or farther than the actual screen.
This may cause you to misjudge the distance to the
screen and possibly result in injury if you accidentally
hit the screen or surrounding objects.
Warning!
The following people should limit 3D viewing:
– Children under 5 years of age (to protect the eye
growth process)
– People with a history of photosensitivity
– People with heart disease
As you get more comfortable viewing 3D images:
Operate the “3D Depth Adjust” function to adjust the
3D effect. (See page 55.)
Adjust the projected image to the most comfortable
viewing size by zooming. (Projecting images on the
smallest or largest screen size possible may eliminate
the 3D effect and strain your eyes.)
Use the Invert function to properly set the video for your
left and right eyes. (For details on using “Invert”, see
page 55.)
A picture simultaneously projected from more than
two projectors may not appear 3D.
– People in poor health
– People who are sleep deprived
– People who are physically tired
– People under the influence of drugs or alcohol
Epilepsy
A small percentage of the population may
experience epileptic or strokes seizures or strokes
when viewing certain types of images that contain
flashing patterns of light.
IF YOU OR ANY MEMBER OF YOUR FAMILY
HAS A HISTORY OF EPILEPSY
The following people should consult a physician
before viewing 3D images.
Info
• The projected image may become dark when
using the 3D projection function (with “3D” set to
“On”).
• When “3D” is set to “On”, the following functions
may not work fully or may not be available at all.
– Keystone/Sphere/Rotation
– Anyone with a history of epilepsy, or who has
a family member with a history of epilepsy
– Children under 5 years of age
– Anyone who has ever experienced epileptic
seizures or sensory disturbances triggered by
flashing light effects
SOME LIGHT PATTERNS MAY INDUCE
SEIZURES IN PERSONS WITH NO PRIOR
HISTORY OF EPILEPSY
Discontinue use if you experience any of the
following symptoms while viewing 3D images.
– Involuntary movements, eye or muscle
twitching
– Muscle cramps
– Nausea, dizziness, or queasiness
– Convulsions
– Image Shift
– Magnify
• If the power of your left and right eyes greatly
differs and you primarily use one eye for viewing
the images, the images will not appear in 3D. In
addition, images may be difficult to view in 3D
or images may not be able to be viewed in 3D
depending on the individual or the content being
displayed. The 3D effect varies with the individual.
– Disorientation, confusion, or loss of
awareness of your surroundings
-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying 3D Image Viewing (Continued)
Supplied Accessories for 3D Glasses
Make sure the following accessories are provided with the 3D Glasses. Two sets of 3D Glasses are provided.
3D Glasses
(×2)
Pages 51 to 54
3D Glasses band *
(×2)
Nose pad *
(Large ×2, small ×2)
Page 52
Page 52
Glasses case
(×2)
Cleaning cloth
(×2)
Precision screwdriver
(Phillips ×2, slotted ×2)
Page 51
* Use the 3D Glasses band and nose pad as needed.
Note
•Please contact your local authority for the correct method of disposal of this product and/or packaging.
1
Power button
• Press for at least 2 seconds to turn on and off the
3D Glasses.
Part Names
• When the 3D Glasses are turned on, pressing this
button switches between 2D and 3D modes. (See
page 52.)
1
2
2
LED light
• Blinks 3 times when the power is turned on.
• Blinks 2 times when 2D mode is selected.
• Blinks 3 times when 3D mode is selected.
• Blinks 6 times when the battery power is low.
• Lights for 2 seconds when the power is turned off.
3
3
4
Service terminal
This terminal is for service use only.
Please do not connect any other device to this terminal.
4
Infrared receiver
6
An infrared signal sent from the projector is reflected onto
the screen. The reflected infrared signal is then received
by the infrared receiver. The 3D Glasses turn off
automatically after 3 minutes if no signal is received.
5
6
Nose pad mount 52
The dedicated nose pad can be mounted here.
3D Glasses band mount 52
5
The dedicated 3D Glasses band can be mounted here.
Note
•Do not soil or apply stickers or other obstacles to the infrared receiver. Doing so may block signals from
the screen and prevent the 3D Glasses from working correctly.
•Interference from other infrared communications equipment may prevent you from viewing 3D images
correctly.
-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the button cell battery.
1Place the tip of the slotted precision screw-
driver into the opening between the button
cell and the socket.
2
Before Using the 3D Glasses
Before using the 3D Glasses for the first time,
remove the insulating sheet attached to them.
2Lift up the button cell while taking care not
to get the screwdriver caught on the metal
latch.
2
1
When the battery comes loose from
the socket, pick it out with your
fingers.
Replacing the Button Cell
Battery
The battery has an expected service life of ap-
proximately 75 hours.
• When the battery power is low, the LED light
blinks six times after the power is turned on.
• When replacing the button cell, use only the
designated battery type (Maxell branded
CR2032 lithium button battery).
Hook a new button cell to the metal
latch and insert it into the socket.
•Take care not to reverse the battery polarity
(+ and -) when inserting the button cell.
Loosen the screw used to secure
the battery cover, and then remove
the battery cover.
Close the battery cover.
5
Insert the screw to secure the bat-
tery cover.
1
2
Note
•Used batteries should be disposed in accor-
dance with local laws and regulations.
-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying 3D Image Viewing (Continued)
Note
Attaching the Nose Pad
•When the battery power is low, the LED light
blinks 6 times after the power is turned on.
Attach either of the supplied nose pads as
needed (such as when the glasses do not fit
properly). The glasses come with a large and
small nose pad.
Switching to 3D and 2D Mode
When viewing 3D images, you can press the
power button to switch between 2D and 3D
modes. This is useful when several people are
viewing the same 3D images with some people
wanting to watch in 3D and some people want-
ing to watch in 2D.
Viewing 2D images
When you press the power button twice while viewing
3D images, the LED light blinks 2 times and the 3D
images switch to 2D images.
1
1
Viewing 3D images
2
When you press the power button twice while viewing
2D images, the LED light blinks 3 times and the 2D
images switch to 3D images.
Attaching
the nose pad
Removing
the nose pad
Attaching the 3D Glasses
Band
Usage Range of the 3D
Glasses
An infrared signal sent from the projector is re-
flected onto the screen. The 3D Glasses operate
by receiving the reflected infrared signal.
The 3D Glasses turn off automatically after 3
minutes if no signal is received.
Attach the supplied 3D Glasses band strap as
needed (such as when the glasses do not fit
properly).
Insert the ends of the 3D Glasses into the 3D
Glasses band until they are secure.
• Pull the cord stopper on the strap to adjust
the strap length.
The operating range of the 3D Glasses is shown in the
table below.
Operating range
“IR Emitter Level” setting
(distance from the screen)
Normal
High
Approx. 12.3 ft (3.8 m)
Approx. 18.3 ft (5.6 m)
(For details of the “IR Emitter Level”, see page 55.)
• Be sure to stay within the operating range when
watching 3D images. Otherwise, the 3D Glasses
may not work properly and you may not be able to
enjoy the 3D images.
• The operating range in the table above is the aver-
age value when using a screen with a screen gain of
1.0 and when viewing in front of the screen.
The operating range may vary depending on your
view position and/or the usage condition (e.g., Gain
level of screen).
Using the 3D Glasses
Turning On/Off the Power
Turn on the power of the 3D Glasses.
•Press the power button for at least 2 seconds.
•The LED light blinks 3 times.
(The operating range decreases when you view the
screen at an angle.)
Turn off the power on the 3D Glasses.
•Press the power button for at least 2 seconds.
•The LED light lights for 2 seconds.
-52
Note
•The IR (infrared) emitter lights in 3D mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
3D MENU button
ENTER button
Adjustment buttons
('/"/\/|)
3D MENU button
3D ON/OFF button
Note
•
The screen may temporarily become black when
the projector is trying to detect a 3D image
signal and when switching from 3D to 2D mode.
Viewing 3D Images
Receiving a 3D Image Signal That
Can Be Detected Automatically
The image signal may contain a 3D identifica-
tion signal. You can enable the projector to
automatically detect the 3D image type by
selecting “3D MENU” > “3D Auto Change”.
(See page 55.)
When “3D Auto Change” is set to “Yes”
Turn on the 3D Glasses and place
them over your eyes.
•Press the power button for at least 2 sec-
onds.
2
•The 3D image type is detected automatically
and the appropriate 3D image is displayed.
•The LED light blinks 3 times.
When “3D Auto Change” is set to “No”
•The following message is displayed. Press
3D ON/OFF.
You can now view 3D images.
3D picture is detected.
Press the 3D ON/OFF button on the remote control.
(Need to wear the 3D glasses to watch 3D picture)
-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying 3D Image Viewing (Continued)
Ending 3D Image Viewing
Receiving a 3D Image
Signal That Cannot Be
Detected Automatically
Press 3D ON/OFF during the 3D
mode.
Press 3D MENU.
Take off the 3D Glasses and turn
off the power.
•Press the power button for at least 2 sec-
onds.
•The 3D MENU screen is displayed.
Press P/Rto select “3D”.
•The LED light lights for 2 seconds.
Press O/Qto select “On” or “Off”.
•To view in 3D mode: Select “On”, and then
go to step 4.
Note
•If the input signal switches to 2D, 2D images
are displayed automatically.
•3D mode is canceled automatically in the fol-
lowing cases:
- When the signal is no longer received
- When the signal type changes
- When input selection is changed
- When the power is turned off
•Refer to “Setting the 3D Format Menu”
on page 56 for supported 3D signals and
formats.
•If you select “Off”, the video source will be
displayed with no conversion.
Press P/R to select “3D Format”,
and then press ENTER.
Press P/R to select a supported
format from the list, and then press
ENTER.
Auto
Side By Side
Top And Bottom
•If you select the same system as that of the
input signal, 3D images are displayed.
Turn on the 3D Glasses and place
them over your eyes.
•Press the power button for at least 2 sec-
onds.
•The LED light blinks 3 times.
You can now view 3D images.
-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
3D Settings (“3D MENU”)
The illustration shown here is for explanation and may
be different from the actual on-screen display.
3D MENU
•Use this function to get more comfortable 3D
images.
•When you use this function, the 3D image will
look different from its original 3D appearance.
Keep this in mind while using this function.
•The use of this function for commercial pur-
poses/public displays in a café, hotel, etc.,
may be an infringement of copyright protected
by law for copyright holders. Please use cau-
tion.
3D
3D Format
On
Auto
0
Normal
Yes
3D Depth Adjust
IR Emitter Level
3D Auto Change
Viewing Time Info
Invert
Yes
IR Emitter Level
You can change the infrared emitter level.
Selectable items
Normal
Description
3D
Normal infrared emitter level
You can switch between 2D and 3D mode.
Selectable items Description
On Projects 3D images.
Off
High
Select “High” when it is difficult for
3D Glasses to properly receive the
infrared signal reflected off the screen
due to the use of a large screen and
viewers being positioned away from
the screen.
Projects 2D images instead of 3D
images.
Note
Note
•When “3D Auto Change” is set to “Yes” and a
3D signal is detected, “3D” switches to “On”.
•When a 3D identification signal is not detected:
- If you selected “On”, select the format with
“3D Format”.
•When “High” is set, other nearby devices that
receive infrared signals, such as remote control
units of audio-video equipment and air condi-
tioners, may not operate properly.
- If you select “Off”, the video source will be
displayed with no conversion.
3D Auto Change
This setting can be used to switch to 3D mode automati-
cally when a 3D identification signal is detected.
3D Format
You can set the 3D format manually for when a 3D signal
that cannot be detected automatically is received.
Selectable items
Yes
Description
When a 3D signal is detected, 3D
mode is selected automatically.
Selectable items
Description
No
Auto change is not performed.
Auto
When a 3D identification signal is
detected, the format is selected
automatically.
Viewing Time Info
This displays the elapsed time of 3D image viewing.
Side By Side
Top And Bottom
Select the same format type of the
received 3D signal.
Selectable items
Yes
Description
Displays the elapsed viewing time on
the screen every hour.
Note
No
Does not display the elapsed viewing
time.
•Refer to “Setting the 3D Format Menu” on
page 56 for supported signals and 3D formats.
Invert
3D Depth Adjust
Pressing ENTER switches between the image for the
left eye and the image for the right eye, so that you can
make the settings for more natural viewing.
You can adjust the stereoscopic effect of 3D image.
Selectable items
\ button
Description
For less stereoscopic effect.
For greater stereoscopic effect.
| button
-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying 3D Image Viewing (Continued)
Setting the 3D Format Menu
Select the appropriate 3D format for viewing while referring to the table below.
When “3D” is ON
3D Format
When “3D”
is OFF
Input signal
Support
Top And
Bottom
Auto
Side By Side
720P
720P
50Hz
60Hz
Frame Packing
Displays
image for
left eye
Displays
correct 3D
image
1080I 50Hz
1080I 60Hz
1080P 24Hz
1080P 50Hz
1080P 60Hz
with 3D
identification
signal
–*1
–*1
(2D mode)
(3D mode)
720P
720P
50Hz
60Hz
Displays
image for
left eye
Displays
correct 3D
image
1080I 50Hz
1080I 60Hz
1080P 24Hz
1080P 50Hz
1080P 60Hz
with 3D
identification
signal
–*1
–*1
(2D mode)
(3D mode)
Side By Side
720P
720P
50Hz
60Hz
Displays raw Displays raw Displays
input signal
Garbled
display
input signal
correct 3D
image
1080I 50Hz
1080I 60Hz
1080P 24Hz
1080P 50Hz
1080P 60Hz
(Incorrect
setting)
without 3D
idetification
signal
*2 (3D mode)
720P
720P
50Hz
60Hz
Displays
image for
left eye
Displays
correct 3D
image
1080I 50Hz
with 3D
identification
signal
(2D mode)
(3D mode)
–*1
–*1
1080I 60Hz
Top And Bottom
1080P 24Hz
1080P 50Hz
1080P 60Hz
720P
720P
50Hz
60Hz
Displays raw Displays raw Garbled
input signal
Displays
correct 3D
image
input signal
display
(Incorrect
*2 setting)
1080I 50Hz
1080I 60Hz
1080P 24Hz
1080P 50Hz
1080P 60Hz
without 3D
idetification
signal
(3D mode)
*1 “3D Format” is set to “Auto” automatically.
*2 The frame rate is changed.
-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
•These 3D Glasses can only be used with Sharp 3D-compatible LCD TVs or projectors that use infrared
control technology.
3D Glasses lenses
•Do not apply pressure to the lenses of the 3D Glasses. Also, do not drop or bend the 3D Glasses.
•Do not scratch the surface of the lenses of the 3D Glasses with a pointed instrument or other object.
Doing so may damage the 3D Glasses and reduce the quality of the 3D image.
•Use only the cloth provided with the 3D Glasses to clean the lenses.
3D Glasses infrared receiver
•Do not allow the infrared receiver to become dirty, and do not attach stickers to or otherwise cover the
infrared receiver. Doing so may prevent the receiver from operating normally.
•If the 3D Glasses are affected by other infrared data communication equipment, the 3D images may not
be displayed correctly.
Caution during viewing
•Do not use devices that emit strong electromagnetic waves (such as cellular phones or wireless trans-
ceivers) near the 3D Glasses. Doing so may cause the 3D Glasses to malfunction.
•The 3D Glasses cannot operate fully at extreme high or low temperatures. Please use them within the
specified usage temperature range.
•If the 3D Glasses are used in a room with fluorescent lighting (60 Hz), the light within the room may ap-
pear to flicker. In this case, either darken or turn off the fluorescent lights when using the 3D Glasses.
•Wear the 3D Glasses correctly. 3D images will not be correctly visible if the 3D Glasses are worn upside
down or back-to-front.
•Other displays (such as computer screens, digital clocks, and calculators) may appear dark and difficult
to view while wearing the 3D Glasses. Do not wear the 3D Glasses when watching anything other than
3D images.
•If you lie on your side while watching the screen with 3D Glasses, the picture may look dark or may not
be visible.
•Be sure to stay within the viewing angle and optimum viewing distance when watching 3D images. Oth-
erwise, you may not be able to enjoy the full 3D effect.
•The 3D Glasses may not work properly if there is any other 3D product or electronic devices turned on
near the glasses or projector. If this occurs, turn off the other 3D product or electronic devices or keep
the devices as far away as possible from the 3D Glasses.
•Stop using this product in any of the following situations:
–When images consistently appear doubled while you are wearing the 3D Glasses
–When you have difficulty perceiving the 3D effect
•If the 3D Glasses are faulty or damaged, stop using them immediately. Continued use of the 3D Glasses
may cause eye fatigue, headaches and illness.
•If you have any abnormal skin reaction, stop using the 3D Glasses. In very rare instances, such reactions
may be due to an allergic reaction to the coating or materials used.
•If your nose or temples become red or you experience any pain or itchiness, stop using the 3D Glasses.
Pressure caused by long periods of use may lead to such reactions and may result in skin irritation.
-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying 3D Image Viewing (Continued)
Specifications – 3D Glasses
Model
AN-3DG10
Lens type
Power supply
Battery
Liquid crystal shutter
3 V DC
Lithium button battery (CR2032 × 1)
Approx. 75 hours of continuous use
/ /64 inch
6 13 16 × 1 7/8 × 6 45
Battery life
Dimension
(W x H x D)
(172.7 × 47.5 × 170.0 mm)
Weight
0.2 lbs./65.0 g (including the lithium button battery)
50°F to 104°F (10°C to 40°C)
(The 3D Glasses cannot operate fully at extreme high or low temperatures. Please use them
within the specified usage temperature range.)
Operating temperature
The product serial number is displayed on the 3D Glasses as indicated in the illustration
on the left. The first four digits represent the product color and the date of manufacture.
Example: Silver colored glasses manufactured on August 11, 2010
Bottom
S/N : S 0 8 B
Manufacture number
Year of
Color
Month of
Day of
manufacture
manufacture
manufacture
S: Silver
R: Red
A: Blue
0: 2010
1: 2011
2: 2012
1: 1
2: 2
3: 3
1: 1 A : 10
2: 2
3: 3
B : 11
H : 17
J : 18
8:8
9:9
N : 22
P : 23
A:10
B:11
C:12
W: 30
X : 31
*“I”, “O”, “Y”, and “Z” are not used.
These symbols displayed on the product and the individual carton package of the product are symbols about the
environment in Japan, China and the EU.
For Japan only:
For China only:
For China only:
For the EU only:
-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the lens
Cleaning the projector
Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coating
film on the surface of the lens.
Ensure that you have unplugged the power cord
before cleaning the projector.
The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
Do not use volatile agents such as insecticides on
the projector.
As the surface of the lens can easily get damaged,
be careful not to scrape or hit the lens.
Do not attach rubber or plastic items to the projec-
tor for long periods.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
Wipe off dirt gently with a soft flannel cloth.
Using a chemical cloth (wet/dry sheet type cloth,
etc.) may deform the components of the cabinet
or cause cracking.
Wiping with a hard cloth or using strong force may
scratch the cabinet surface.
When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth
well and then wipe the projector.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Strong cleaning detergents may discolor, warp or
damage the coating on the projector. Make sure to
test on a small, inconspicuous area on the projec-
tor before use.
Mild detergent diluted
with water
Info
• If you want to clean the air vents during projector
operation, ensure you press STANDBY/ON on
the projector or STANDBY on the remote control
and put the projector into standby mode. After
the cooling fan has stopped, clean the vents.
Thinner
Wax
-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector
indicate problems inside the projector.
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and
the projector will enter standby mode. After the projector has entered standby mode, follow the procedures
given below.
Top View
Power indicator
Lamp indicator
Temperature warning
indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting
location, the temperature warning indicator will blink. And if the temperature keeps on rising,
“
” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking.
If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter
standby mode. When you find the temperature warning indicator blinking, be sure to perform the measures
described on page 61.
About the lamp indicator
When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on
the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off
and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate
in red.
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not
turn on.
Indicators on the Projector
Power indicator
Red on
Normal (Standby)
Green on
Red blinks
Green blinks
Normal (Power on)
Abnormal (See page 61.)
Normal (Cooling)
Green and orange blink
alternately
The lens shutter is closed. (See page 23.)
Lamp indicator
Green on
Green blinks
Red on
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be changed. (See
page 61.)
Temperature warning Off
indicator
Normal
Red on/Red blinks
The internal temperature is abnormally high. (See page 61.)
-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance indicator
Problem
Cause
Possible Solution
Normal
Abnormal
Temperature
warning
indicator
Off
Red blinks The internal
• Temperatures
around the
projector are
high.
• Use the projector in an area with a
temperature of lower than 95°F (+35ºC).
• Relocate the projector to an area with
proper ventilation. (See page 7.)
(On)/
Red on
temperature is
abnormally
(Standby) high.
• Blocked air
intake
• Cooling fan
breakdown
• Internal circuit
failure
• Take the projector to your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 75) for repair.
• Clogged air
intake
Lamp
indicator
Green on
(Green
blinks when
the lamp is
warming up.)
Red on
Red on
The lamp does • The lamp is shut • Disconnect the power cord from the AC
not illuminate.
down
abnormally.
outlet, and then connect it again.
Time to change • Remaining lamp • Carefully replace the lamp. (See page
the lamp.
life becomes 5%
or less.
62.)
• Take the projector to your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 75) for repair.
• Please exercise care when replacing the
lamp.
The lamp does • Burnt-out lamp
(Standby) not illuminate.
• Lamp circuit
failure
• Securely install the cover.
Power
indicator
Green on/
Red on
Green blinks
(Cooling)
Red blinks The power
indicator blinks
• The lamp unit
cover is open.
• If the power indicator blinks in red even
when the lamp unit cover are securely
installed, contact your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 75) for advice.
in red when the
projector is on.
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the pos-
sible solutions above and then wait until the projector has cooled down completely before plugging in the
power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled
automatically. The sound of the cooling fan may change during operation because the fan speed may
change and this is not a malfunction.
-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp
life (percentage) can be checked with the on-screen display. (See page 47.)
Purchase a replacement lamp of type AN-K15LP from your place of purchase, nearest Sharp Autho-
rized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
U.S.A. ONLY
Caution Concerning the Lamp
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
Should the lamp break, there is also a possibility that glass particles may spread inside of the projec-
tor. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer
or Service Center to assure safe operation.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mer-
cury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of
exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns
or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
Carefully change the lamp by following the instructions described in this section. * If you wish, you
may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing the Lamp Unit
• Do not remove the lamp unit from the projector right after use. The lamp and parts
Warning!
around the lamp will be very hot and may cause burns or injury.
Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
Optional
accessory
Lamp unit
AN-K15LP
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
STANDBY/ON button
Press STANDBY/ON on the
projector or STANDBY on the
remote control to put the projec-
tor into standby mode.
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
AC socket
• Leave the lamp until it has fully cooled
down (about 1 hour).
Remove the lamp unit cover.
• Close the lens shutter. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).
2
1
User service screw
(for lamp unit cover)
-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp (Continued)
Securing screws
Remove the lamp unit.
• Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
INTERLOCK
Warning!
Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
5
DO NOT DEFEAT THIS INTERLOCK
Replace the lamp unit cover.
• Align the tab on the lamp unit cover
(1) and place it while pressing the cover
(2) to close it. Then tighten the user
service screw (3) to secure the lamp
unit cover.
Info
• If the lamp unit and lamp unit cover are
not correctly installed, the power will
not turn on, even if the power cord is
connected to the projector.
1
2
3
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this
may cause the lamp to become damaged
or explode.
AC socket
Lamp indicator
STANDBY/
ON button
Connect the power cord and
open the lens shutter fully.
• Plug the power cord into the AC socket
of the projector.
ENTER
button
R
button
MENU button
Reset the lamp timer.
•
While simultaneously holding down
MENU, ENTER and R on the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
• “LAMP 0000 H” is displayed, indicating
that the lamp timer is reset.
-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
COMPUTER/COMPONENT input Terminal : mini D-sub 15 pin female connector
COMPUTER Input
Pin No. Signal
COMPONENT Input
Pin No. Signal
15
11
1
Video input (red)
1
PR (CR)
2
3
4
5
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
2
3
4
5
Y
PB (CB)
Not connected
Not connected
Earth (PR)
6
6
1
6
5
10
7
8
Earth (green/sync on green)
Earth (blue)
7
8
Earth (Y)
Earth (PB)
9
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
9
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
10
11
12
13
14
15
10
11
12
13
14
15
RS-232C Terminal: 9-pin D-sub male connector
Pin No. Signal Name
I/O
Reference
1
Not connected
9 8 7 6
2
3
4
5
6
7
8
9
RD
SD
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Input
Output
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
SG
Reserved
Reserved
5 4 3 2 1
HDMI Terminal
Pin No. Name
Pin No. Name
Pin No. Name
18
2
1
2
3
4
5
6
7
T.M.D.S data 2+
T.M.D.S data 2 shield
8
T.M.D.S data 0 shield
T.M.D.S data 0–
T.M.D.S clock+
T.M.D.S clock shield
T.M.D.S clock–
CEC
14
15
16
17
18
19
Utility
SCL
SDA
DDC/CEC ground
+5V power
Hot plug detection
9
T.M.D.S data 2–
T.M.D.S data 1+
T.M.D.S data 1 shield
T.M.D.S data 1–
T.M.D.S data 0+
10
11
12
13
19
1
-65
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 22 for connection.)
Communication conditions
Set the serial port settings of the computer as follows.
Signal format: Conforms to RS-232C standard.
Baud rate*: 9,600 bps / 38,400bps / 115,200bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
*Use the same settings for the projector and computer.
Basic format
Send commands from the computer in the following order: command, parameter, and return code. After
processing the command from the computer, the projector sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH)
Command 4-digit
Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
O
K
E
R
R
Return code (0DH)
Return code (0DH)
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
• After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
• When more than one code is being sent, send each command only after the response code for the previ-
ous command from the projector is verified.
• “POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
−When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
−The special commands are available for applications that require continuous polling.
-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
Example: To turn on the projector
Computer
Projector
→
←
P
O
W
R
1
O
K
_
_
_
Return
Control Contents
Command
Parameter
Standby mode
(or 30-second startup time)
Power ON
Power
On
Off
P
P
T
T
O
O
L
W
W
P
R
R
S
N
_
_
?
_
_
_
?
_
_
_
?
_
1
0
?
1
OK or ERR
OK
OK
1
OK or ERR
Status
0
Projector Condition
A
B
0:Normal
0:Normal
1:Temp High
1:Temp High
2:Fan Error
4:Lamp Cover Open
8:Lamp Life 5% or less
16:Lamp Burnt-out
32:Lamp Ignition Failure
64:Temp Abnormally High
8:Lamp Life 5% or less
16:Lamp Burnt-out
32:Lamp Ignition Failure
Lamp
Status
T
L
P
S
_
_
_
1
0:Off, 1:On, 2:Retry
3:Waiting, 4:Lamp Error
0:Off, 4:Lamp Error
Power Status
T
T
T
T
T
T
M
P
P
P
P
I
P
L
L
L
L
N
N
J
O
P
T
W
N
T
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
1
1
1
1
1
1
1
*
1:On, 2:Cooling
1
0:Standby
Quantity
Usage Time (Hour)
Usage Time (Minuite)
Life (Percentage)
Model Name Check
Model Name Check
0-9999 (Integer)
0, 15, 30, 45
0%-100% (Integer)
XVZ17000
T
M
L
T
Name
A
R
N
N
N
N
G
G
G
G
E
M
D
1
XV-Z17000
Projector Name Setting1 (First 4 characters) *1
OK or ERR
Projector Name Setting2 (Middle 4 characters) *1
J
2
*
*
*
*
OK or ERR
Projector Name Setting3 (Last 4 characters) *1
J
3
*
*
*
*
OK or ERR
Projector Name Check
COMPUTER
COMPONENT
HDMI1
J
0
_
_
_
_
_
_
_
?
_
_
_
_
_
_
_
?
_
_
_
_
_
_
_
?
1
1
2
3
4
1
2
?
Projector Name
OK or ERR
Input Change
R
R
R
R
V
V
R
B
B
B
B
D
D
B
ERR
ERR
ERR
ERR
ERR
ERR
ERR
I
OK or ERR
I
OK or ERR
HDMI2
I
OK or ERR
S-VIDEO
I
OK or ERR
VIDEO
I
E
OK or ERR
Input RGB Check
I
G
1: COMPUTER, 2: COMPONENT,
3: HDMI1, 4: HDMI2, ERR
1: S-VIDEO, 2: VIDEO, ERR
1: RGB, 2: VIDEO
Input Video Check
Input Mode Check
Input Check
I
I
I
V
M
C
E
O
H
D
D
K
?
?
?
?
?
?
?
?
?
?
?
?
ERR
ERR
ERR
1: COMPUTER
2: COMPONENT
3: HDMI1
4: HDMI2
5: S-VIDEO
6: VIDEO
Resize
COMPUTER
COMPONENT
HDMI1
Normal
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C
D
D
D
D
D
D
A
A
A
A
A
B
B
B
B
B
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
V
V
V
V
V
V
V
V
V
V
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
2
3
5
7
6
1
2
3
5
7
6
1
2
3
5
7
6
1
2
3
5
7
6
1
2
5
7
6
1
2
5
7
6
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
16:9
Native
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
16:9
Native
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
16:9
Native
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
HDMI2
16:9
Native
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
S-VIDEO
VIDEO
16:9
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
16:9
Cinema Zoom
Zoom14:9
Smart Zoom
-67
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands (Continued)
Return
Control Contents
Command
Parameter
Standby mode
(or 30-second startup time)
Power ON
ALL Reset
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
L
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
R
E
S
S
S
S
S
S
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
COMPUTER INPUT
Picture Mode
Standard
Natural
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2 - +2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
COMPONENT INPUT
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2 - +2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
HDMI1
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2 - +2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
HDMI2
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2 - +2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
_
_
*
*
_
1
-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Return
Control Contents
Picture Mode
Command
Parameter
Standby mode
Power ON
(or 30-second startup time)
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
S-VIDEO INPUT
Standard
Natural
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
T
T
3
3
3
3
3
3
L
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
F
P
S
S
S
S
S
S
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
_
_
_
_
_
_
*
_
_
_
_
_
_
*
1
2
3
4
5
6
*
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
R
R
E
E
F
F
F
I
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2 - +2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
VIDEO INPUT
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2 - +2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
Q
Q
N
N
M
M
M
V
E
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Horizontal
Vertical
On
_
_
_
_
_
_
_
_
_
_
0
*
*
_
_
_
_
_
_
_
_
_
0
1
1
2
1
0
0
1
2
1
1
RGB Frequency Check
3D
kHz (***.* or ERR)
Hz (***.* or ERR)
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
F
D
D
D
D
D
D
P
Off
3D Format
Auto
Side By Side
Top And Bottom
Invert
Lamp Timer Reset *2
R
OK, ERR
Note
•If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value
in the range indicated in brackets under Control Contents.
*1 For setting the projector name, send the commands in order of PJN1, PJN2 and PJN3.
*2 The Lamp Timer Reset command can only be sent in standby mode.
-69
Download from Www.Somanuals.com. All Manuals Search And Download.
Compatibility Chart
Computer
• Multiple signal support
Horizontal Frequency: 15–110 kHz, Vertical Frequency: 43–85 Hz, Pixel Clock: 12–170 MHz
• Compatible with sync on green and composite sync signals (TTL level)
Horizontal frequency
[kHz]
Vertical
frequency[Hz]
Analog
Support
Digital
Support
PC/MAC
Mode
Resolution
Display
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
47.7
47.8
55.9
55.0
66.2
67.5
60.0
64.0
64.0
65.3
55.9
65.3
66.8
60
70
85
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
60
60
60
60
70
75
60
60
60
60
60
60
60
640 × 400
720 × 400
640 × 480
VGA
SVGA
XGA
800 × 600
1024 × 768
Upscale
PC
1280 × 720
1280 × 768
1280 × 800
1360 × 768
1366 × 768
1440 × 900
WXGA
WXGA+
SXGA
1152 × 864
1280 × 960
1280 × 1024
SXGA+
1400 × 1050
1600 × 900
1680 × 1050
1920 × 1080
*
1
WSXGA+
Down sampled
Intelligent
Compression
2
1920 × 1080
*
67.5
60
MAC 13"
MAC 16"
MAC 19"
MAC 21"
VGA
SVGA
XGA
640 × 480
832 × 624
1024 × 768
1152 × 870
34.9
49.7
60.2
68.7
67
75
75
75
Upscale
SXGA
*1 When a 1920 × 1080 analog signal is input, the image is compressed before it is displayed on the screen.
*2 Full image display when “Resolution” is set to “1920 × 1080”
Note
•This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
•When “Screen resolution” of the computer is different from the resolution displayed on the projected im-
age, follow the procedures shown below.
–Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in “Screen
resolution” of the computer.
–Depending on the computer you are using, the output signal may not be faithful to the “Screen reso-
lution” adjustment. Check the settings of the computer's signal output. If the settings cannot be
changed, it is recommended that the resolution be set to “1920 × 1080” or “1280 × 720”.
-70
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Analog
Support
Digital
Support
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Analog
Support
Digital
Support
Signal
Signal
15.7
31.5
33.8
15.6
31.3
37.5
45.0
60
60
60
50
50
50
60
28.1
33.8
27.0
28.1
33.8
56.3
67.5
50
60
24
25
30
50
60
480I
480P
540P
576I
1080I
1080I
1080P
1080P
1080P
1080P
1080P
576P
720P
720P
3D
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Analog
Support
Digital
Support
Format
Signal
720P
720P
75.0
90.0
54.0
37.5
45.0
28.1
33.8
56.3
67.5
37.5
45.0
27.0
56.3
67.5
50
60
24
50
60
50
60
50
60
50
60
24
50
60
Frame
Packing
1080P
720P
720P
1080I
1080I
1080P
1080P
720P
Side By
Side
720P
Top And
Bottom
1080P
1080P
1080P
-71
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The lens shutter is closed.
23
–
23, 28
27, 41, 42
19-23
13
• The selected input mode is wrong.
• Cables are incorrectly connected to the projector.
• Remote control battery has run out.
• External output has not been set when connecting notebook computer.
• The lamp unit cover is not installed correctly.
• The selected “Signal Type” is wrong.
–
No picture or projector does
not start
63, 64
41
•
The video signal format of the video equipment is not set correctly.
42
• “Bright” is set to minimum position.
37
• Image adjustments are incorrectly set.
37
(S-VIDEO or VIDEO input)
• Video input system is incorrectly set.
(COMPONENT, COMPUTER/COMPONENT or HDMI1, 2 input)
• Input signal type is incorrectly set.
42
41
Color is faded or poor.
• Adjust the focus.
24
18
• The projection distance exceeds the focus range.
(Computer input)
• Perform “SIG-ADJ” Adjustments (“Clock” Adjustment)
• Perform “SIG-ADJ” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
41
41
–
• The “DNR” (Digital Noise Reduction) or “MNR” (Mosquito Noise Reduc-
tion) setting is not correct.
40
Picture is blurred;
noise appears.
• There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the surface
of the lens and the image will become blurred. Please set up the projector at
least one hour before it is to be used. If condensation should form, remove the
power cord from the wall outlet and wait for it to clear.
–
An unusual sound is
occasionally heard
from the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage caused
by a room temperature changes. This will not affect operation or perfor-
mance.
–
Maintenance
indicator on the
projector illuminates.
• See “Maintenance Indicators”.
60
41
Picture is green when
receiving YPbPr
• Change the input signal type setting.
signals and the video
equipment is connected
to the COMPONENT or
COMPUTER/COMPONENT
terminal on the projector.
Picture is pink when receiv-
ing RGB signals and the video
equipment is connected to the
COMPONENT or COMPUTER/
COMPONENT terminal on the
projector.
The black levels of the
image show banding or
appear faded when HDMI1
or 2 is selected.
• Make adjustments that result in the best picture quality in the “Dynamic
42
37
Range” setting.
Picture is too bright and
whitish.
• Image adjustments are incorrectly set.
-72
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Page
The cooling fan
becomes noisy.
• When temperature inside the projector increases, the cooling fan runs
faster.
–
The lamp does not light up
even after the
• The lamp indicator is illuminating in red.
Replace the lamp.
23, 60, 63
projector turns on.
• The lens shutter is opened fully.
The lamp suddenly turns off
during projection.
The image sometimes
flickers.
• Cables are incorrectly connected to the projector or the connected equip-
ment works improperly.
• If this happens frequently, replace the lamp.
19-22
63
The lamp needs much time
to turn on.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
63
Picture is dark.
One Touch Play is not
enabled.
• Non-Sharp Video Products are connected.
One Touch Play function may not work when the projector is connected
to non-Sharp Video Products.
46
20
• An HDMI cable is not used for connection between the projector and the
Sharp Video Products.
One Touch Play function is enabled when the projector is connected to
the Sharp Video Products with an HDMI cable.
• One Touch Play function of the projector is not set to “On”.
46
–
• CEC settings of connected Sharp Video Products or other CEC devices
are incorrect.
• One Touch Play is set to “Off” and disabled when the Economy mode is
46
46
set to “On”.
System Standby is not
enabled.
• Non-Sharp Video Products are connected.
System Standby function may not work when the projector is connected
to non-Sharp Video Products.
• An HDMI cable is not used for connection between the projector and the
Sharp Video Products.
20
System Standby function is enabled when the projector is connected to
the Sharp Video Products with an HDMI cable.
• System Standby function of the projector is not set to “On”.
46
–
• CEC settings of connected Sharp Video Products or other CEC devices
are incorrect.
A response code cannot be
received when the
projector was attempted
to be controlled using
• In the case of transmitting RS-232C commands from a computer during
standby, it takes a maximum of 30 seconds for the computer to receive
the response code. Set the response code waiting time of the computer
to 30 seconds or more.
66
RS-232C commands from
a computer during standby.
The remote control
cannot be used.
• Operate the remote control while pointing it at the projector’s remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the projector’s
remote control sensor, place the projector where it will not be affected by
strong light.
13
13
13
• The batteries may be depleted or inserted incorrectly. Make sure the bat-
teries are inserted correctly or insert new ones.
13
-73
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Continued)
Problem
Check
Page
53, 54, 55
55
3D images are not
displayed.
• Switch to 3D mode.
• Is “3D Auto Change” set to “No”? Press 3D ON/OFF to switch to 3D
mode.
• If “3D Auto Change” is set to “Yes” but no 3D images are displayed,
check the display format of the content being viewed. Some 3D image
signals may not be recognized as 3D images automatically. Press 3D
MENU to select the appropriate display format for the 3D image.
55, 56
• The 3D Glasses are not turned on.
52
52
–
• The 3D Glasses are set to 2D mode.
• The 3D Glasses operate by receiving the infrared signal reflected onto
the screen. Do not place anything between the screen and the infrared
receiver on the 3D Glasses.
3D Images flicker when
watching in a room.
• Images may appear to flicker when fluorescent light or ambient light
enters your vision.
–
-Turn off the lights.
-Block any ambient light.
Ghosting (a double image)
occurs without the image
appearing in 3D.
• Use “Invert” to change the setting.
55
71
• A signal that does not support 3D is being received. Check whether a
signal that supports 3D is being received.
• If the projector is connected to a computer for 3D image playback,
check that a stereoscopically-enabled application is being used.
–
- Use the applicable software
- Configure your 3D application at the correct 3D format, resolution and
refresh rate. To support 3D, your 3D application must be configured to
run at the correct settings for this projector.
• If there is strong ambient light, block the light. High intensity lighting can
interfere with communication between the 3D Glasses and the screen,
resulting in some flicker.
–
• A picture simultaneously projected from more than two projectors may
–
–
–
not appear 3D. Use only one projector at a time.
The projected image is dark.
• When a 3D image is projected, the screen may appear darker than nor-
mal.
The 3D Glasses turn off
automatically.
• Is there an obstacle between the 3D Glasses and the screen, or is some-
thing covering the infrared receiver on the 3D Glasses? The 3D Glasses
turn off automatically after 3 minutes if no signal is received. Do not
place anything between the screen and the infrared receiver on the 3D
Glasses.
Pressing the power button
on the 3D Glasses does not
cause the LED light to light.
• The battery in the 3D Glasses is exhausted. If the LED light does not light
after pressing the power button for more than one second, the battery is
exhausted. Replace the battery.
51
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the unit and plug it in again after more than
5 minutes.
-74
Download from Www.Somanuals.com. All Manuals Search And Download.
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”
section on pages 72 to 74. If this operation manual does not answer your question, please contact the
SHARP Service departments listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
Canada
Mexico
Sharp Electronics of Canada Ltd.
(905) 568-7140
Australia
Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111
Latin America Sharp Electronics Corp. Latin
American Group
Fax: (09) 573-0112
(305) 264-2277
Singapore
Hong Kong
Taiwan
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
Germany
U.K.
Sharp Electronics (Europe) GMBH
01805-234675
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
Sharp Electronics (U.K.) Ltd.
08705 274277
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
Sharp Corporation (Taiwan)
0800-025111
France
Sharp Electronics France
01 49 90 35 40
Malaysia
U.A.E.
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
Sharp Middle East Fze
971-4-81-5311
Spain
Sharp Electronica Espana, S.A.
93 5819700
Thailand
Korea
Sharp Thebnakorn Co. Ltd.
02-236-0170
Switzerland
Sweden
Austria
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
India
Sharp Business Systems (India)
Limited
(91) 11- 6431313
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
-75
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
XV-Z17000
0.65" DLP® Chip × 1
Display devices
Resolution
1080P (1920 × 1080)
Lens
F number
Zoom
F 2.5 – 2.7
Manual, ×1.15 (f = 21.0 – 24.2 mm)
Focus
Manual
× 2
Input terminals
HDMI
Computer/Component
(mini D-sub 15 pin)
× 1
Component (3RCA)
S-Video (mini DIN 4 pin)
Video (RCA)
× 1
× 1
× 1
× 1
Control and
communication
terminals
RS-232C (mini D-sub 9 pin)
Projection lamp
Rated voltage
Rated frequency
Input current
250 W
AC 100 – 240V
50/60 Hz
3.7 A
Power consumption (Standby)
353 W (7.6 W) with AC 100 V
339 W (8.3 W) with AC 240 V
Operation temperature
Cabinet
41°F to 95°F (+5°C to +35°C)
Plastic
15 3/4" × 3 15/16" × 13 13/64"
(400 × 100 × 335 mm)
Dimensions (main body only) [W × H × D]
Weight (approx.)
12.8 lbs. (5.8 kg)
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of produc-
tion units. There may be some deviations from these values in individual units.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 2,073,600 pixels (micromirrors). As
with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life expectancy of the unit.
-76
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Units: inches (mm)
2 9/16
(65)
4 17/32
(115)
3 23/64
(85)
1/8 (3)
15 3/4 (400)
M4
M4
M4
M4
1 13/16
15/64 (5.75)
(45.75)
7 5/64
4 5/8
2 61/64
(75)
(179.75)
(116.25)
-77
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
16:9....................................................................... 30
3D Auto Change................................................... 55
3D Depth Adjust................................................... 55
3D Format............................................................. 55
3D Glasses ......................................................50-52
3D MENU ............................................................. 55
3D MENU button............................................ 54, 55
3D ON/OFF button ......................................... 53, 54
Accessories............................................................ 9
AC socket............................................................. 23
Adjustment buttons ............................................. 35
Adjustment feet .................................................... 24
Advanced ............................................................. 38
All Reset ............................................................... 47
Auto Power Off..................................................... 46
Auto Sync............................................................. 41
AUTO SYNC button ............................................. 28
Lamp indicator ..................................................... 60
Lamp Timer (Life).................................................. 47
Language (on-screen display language) .............. 45
Lens shutter.............................................. 23, 28, 63
MAGNIFY buttons ................................................ 29
MENU HIDE button .............................................. 29
MENU button........................................................ 35
MNR ..................................................................... 40
Movie1, 2.............................................................. 37
NATIVE.................................................................. 31
Natural.................................................................. 37
ON button............................................................. 23
One Touch Play .................................................... 46
On-screen Display................................................ 45
Optional accessories.............................................. 9
OSD Brightness.................................................... 45
Overscan .............................................................. 43
Phase.................................................................... 41
Picture .................................................................. 37
Picture Mode........................................................ 37
PICTURE MODE button ....................................... 28
Power cord....................................................... 9, 23
Power indicator .............................................. 23, 60
PRJ-ADJ............................................................... 46
PRJ mode....................................................... 17, 45
Remote control..................................................... 12
Remote control sensors ....................................... 13
Replacing the lamp .............................................. 62
RESIZE button...................................................... 30
RETURN button.................................................... 35
Rotation.......................................................... 26, 45
RS-232C............................................................... 47
RS-232C terminal................................................. 22
Saturation............................................................. 39
SCR-ADJ.............................................................. 43
Screen Size and Projection Distance ................... 18
Security bar .......................................................... 11
Select Color.......................................................... 39
Sharp.................................................................... 37
SIG-ADJ ............................................................... 41
Signal Info............................................................. 42
Signal Type........................................................... 41
SMART ZOOM ..................................................... 31
Sphere............................................................ 26, 44
Standard............................................................... 37
STANDBY button.................................................. 23
STANDBY/ON button ........................................... 23
S-VIDEO button.................................................... 27
S-VIDEO terminal ........................................... 19, 20
System Standby................................................... 46
Background.......................................................... 45
Batteries ............................................................... 13
Bright.................................................................... 37
Bright Boost ......................................................... 40
Carrying handle .................................................... 11
Ceiling-mount setup............................................. 17
CINEMA ZOOM.................................................... 30
Clock .................................................................... 41
CLR Temp (Color Temperature)............................ 37
C.M.S. .................................................................. 38
Color..................................................................... 37
COMPONENT button........................................... 27
COMPONENT terminal......................................... 19
COMPUTER button.............................................. 27
COMPUTER/COMPONENT terminal ............. 19, 21
Contrast................................................................ 37
Detail Enhance ..................................................... 40
DNR...................................................................... 40
Dynamic ............................................................... 37
Dynamic Range.................................................... 42
Economy Mode .................................................... 46
ECO+QUIET button.............................................. 29
Effect .................................................................... 39
ENTER button....................................................... 35
Fan Mode ............................................................. 47
Film Mode............................................................. 40
Focus ring............................................................. 24
FREEZE button..................................................... 28
Game.................................................................... 37
Gamma................................................................. 38
HDMI1, 2 buttons................................................. 27
HDMI1, 2 terminals......................................... 19, 20
HEIGHT ADJUST lever......................................... 24
H-Image Shift ................................................. 27, 43
H-Pos ................................................................... 41
Hue....................................................................... 39
IMAGE SHIFT button............................................ 27
INPUT button........................................................ 27
Input Name........................................................... 47
Invert..................................................................... 55
IR Emitter Level .................................................... 55
IRIS1, 2................................................................. 38
IRIS1, 2 buttons.................................................... 29
Temperature warning indicator............................. 60
Tint........................................................................ 37
Value..................................................................... 39
VIDEO button ....................................................... 27
Video Setup.......................................................... 42
Video System ....................................................... 42
VIDEO terminal..................................................... 19
Viewing Time Info ................................................. 55
V-Image Shift.................................................. 27, 43
V-Pos.................................................................... 41
ZOOM 14:9........................................................... 31
Zoom ring............................................................. 24
Kensington Security Standard connector ............ 11
KEYSTONE button ............................................... 25
-78
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
Printed in China
Imprimé en Chine
Impreso en China
Impresso na China
TINS-E929WJZZ
11P01-CH-NM
Download from Www.Somanuals.com. All Manuals Search And Download.
|