Sylvania Flat Panel Television 6626LDG User Manual

26” High Definition LCD TV

built-in DVD Player

OWNER’S MANUAL

6626LDG A

6626LDG

HIGH-DEFINITION TELEVISION

INSTRUCCIONES EN ESPAÑOL INCLUIDAS

TO RECEIVE DIGITAL/ANALOG SIGNAL,

YOU MUST CONNECT ANTENNA.

IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER

READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR

VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.com

Download from Www.Somanuals.com. All Manuals Search And Download.

15. POWER LINES - An outside antenna system should not be located

in the vicinity of overhead power lines or other electric light of

power circuits, or where it can fall into such power lines or circuits.

When installing an outside antenna system, extreme care should be

taken to keep from touching such power lines or circuits as contact

with them might be fatal.

16. OVERLOADING - Do not overload wall outlets and extension cords

as this can result in a risk of ﬁre or electric shock.

17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into

this TV through openings as they may touch dangerous voltage

points or short out parts that could result in a ﬁre or electric shock.

Never spill liquid of any kind on the TV.

18. SERVICING - Do not attempt to service this TV yourself as opening

or removing covers may expose you to dangerous voltage or other

hazards. Refer all servicing to qualiﬁed service personnel.

19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall

outlet and refer servicing to qualiﬁed service personnel under the

following conditions:

c. If the TV has been exposed to rain or water.

d. If the TV does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions, as improper adjustment of other controls

may result in damage and will often require extensive work by a

qualiﬁed technician to restore the TV to its normal operation.

e. If the TV has been dropped or damaged in any way.

f. When the TV exhibits a distinct change in performance, this

indicates a need for service.

20. REPLACEMENT PARTS - When replacement parts are required, be

sure the service technician uses replacement parts speciﬁed by

the manufacturer that have the same characteristics as the original

part. Unauthorized substitutions may result in ﬁre, electric shock,

injury to persons or other hazards.

21. SAFETY CHECK - Upon completion of any service or repairs to this

TV, ask the service technician to perform routine safety checks to

determine that the TV is in proper operating condition.

22. HEAT - This TV product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products (includ-

ing ampliﬁers) that produce heat.

a. When the power supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the TV.

5PRECAUTIONS

LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.

CAUTION:

ATTENTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment

may cause harmful interference unless the modifications are expressly approved in the owner’s manual. The

user could lose the authority to operate this equipment if an unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the build-

ing as close to the point of cable entry as practical.

LASER SAFETY

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to

possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK MECHANISM.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual prop-

erty rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home

and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is

prohibited.

Download from Www.Somanuals.com. All Manuals Search And Download.

NTRODUCTION

LOCATION

For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation:

• Shield it from direct sunlight and keep it away from sources of intense heat.

• Avoid dusty or humid places.

• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the

unit. Do not place the unit on a carpet because this will block the ventilation holes.

• Install unit in a horizontal position.

• Avoid locations subject to strong vibration.

• Do not place the unit near strong magnetic fields.

• Avoid moving unit to locations where temperature differences are extreme.

• Be sure to remove disc and unplug the AC power cord from the outlet before carrying the unit.

TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.

• If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our Authorized Service Center

for servicing.

• Do not put your fingers or objects into the unit or disc loading slot.

• Do not place anything directly on top of the unit.

MOISTURE WARNING

• Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold

room or under conditions of high humidity. If you play a DVD or Audio CD in a moist unit, it may damage the DVD or Audio

CD and the unit. When the condensation occurs inside the unit, turn the unit on and leave it at least 2 hours to dry out.

The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You

should record the number and other vital information here and retain this book as a permanent record of your purchase to aid

identification in case of theft.

Date of Purchase

Dealer Purchase from

Dealer Phone No.

Model No.

Serial No.

Dealer Address

Note about recycling:

• This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with

your local recycling regulations.

• Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning

chemical wastes.

5SUPPLIED ACCESSORIES

• Owner’s Manual

(1EMN22057A)

• Remote Control Unit

(NF013UD)

• Batteries

(“AA” x 2)

• If you need to replace these accessories, please refer to the PART No. with the illustrations and call our toll free cus-

tomer support line found on the cover of this manual.

• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).

Contact your local electronics store for these items.

5SYMBOLS USED IN THIS MANUAL

The following is the description for the symbols used in this manual.

Description refers to:

: Analog TV operation.

: Digital TV operation.

DVD

: playback of DVD-Video discs.

: playback of Audio CDs.

DTV

• If neither symbol appears under the function heading,

operation is applicable to both.

MP3

JPEG

: playback of CD-RW/-R with MP3 files.

: playback of CD-RW/-R with JPEG files.

Download from Www.Somanuals.com. All Manuals Search And Download.

5CONTENTS

DVD FUNCTIONS

OPERATING DVD

INTRODUCTION

IMPORTANT SAFEGUARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

REMOTE CONTROL FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PLAYABLE MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

UNPLAYABLE MEDIA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

DVD MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

PAUSED AND STEP-BY-STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

FAST FORWARD / FAST REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

SLOW FORWARD / SLOW REVERSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

MP3, JPEG PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

DUAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

FOLDER PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

TRANSITION MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

ADJUSTMENT OF PICTURE SIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

REPEAT A-B PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

PROGRAMMED PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

ON-SCREEN DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

SPECIAL SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

PREPARATION

CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CONNECTING OTHER DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

TV FUNCTIONS

SETTING TV

INITIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

AUTOSCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CHANNEL LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

MANUAL REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ANTENNA CONFIRMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

LANGUAGE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

SETTING DVD

DVD LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

DVD AUDIO SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

PARENTAL SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

RESET TO THE DEFAULT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

LANGUAGE CODE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

OPERATING TV

CHANNEL SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

VOLUME ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

SELECTING AUDIO CHANNELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ACCESSING EXTERNAL DEVICES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SCREEN INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

CHANGING THE SCREEN DISPLAY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

PICTURE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

CLOSED CAPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

DTV CLOSED CAPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

CLOSED CAPTION STYLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

V-CHIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

HDMI AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

TROUBLESHOOTING

TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

INFORMATION

GLOSSARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

CABLE CHANNEL DESIGNATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

ELECTRICAL SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

OTHER SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

ESPAÑOL

FUNCIONES DEL MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

PANEL DE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

PANEL TRASERO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

CONEXIÓN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

CONEXIÓN DE OTROS DISPOSITIVOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

PREAJUSTES INICIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

PREA. AUTO CA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

LISTA DE CANALES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

REGISTRO MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

REPRODUCCIÓN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

MENÚ DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

REANUDACIÓN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

PAUSA Y REPRODUCCIÓN PASO A PASO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

AVANCE RÁPIDO / RETROCESO RÁPIDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

AVANCE LENTO / RETROCESO LENTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

REPRODUCCIÓN DE MP3, JPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back cover

Download from Www.Somanuals.com. All Manuals Search And Download.

NTRODUCTION

5FEATURES

DVD

• DTV/TV/CATV

• Dolby Digital Sound

- You can use your remote control to select channels

which are broadcast in conventional analog, standard

definition, and high definition formats. Also, cable

subscribers can access their cable TV channels.

• Program Information Display (DTV only)

- You can display the title, contents and other informa-

tion of the current DTV program on the screen.

• Autoscan

- Enjoy Dolby Digital multi-channel surround sound

when you connect your TV to a Dolby Digital decoder.

• Still / Fast / Slow / Step Playback

- Various playback modes are available including still

pictures, fast forward/reverse, slow motion and step

frames.

• Random Playback for Audio CD, MP3 and JPEG

- This unit can shuffle the order of tracks to play them

back in random order.

- Your TV automatically scans and memorizes channels

available in your area, eliminating difficult set-up pro-

cedures.

• Program Playback for Audio CD, MP3 and JPEG

- You can program the order of tracks to play them back

in desired order.

• V-CHIP

- This feature allows you to block children’s access to

inappropriate programs.

• Closed Caption Decoder

• DVD Menus in a Desired Language

- You can display DVD menus in a desired language, if

available on a DVD.

- Built-in closed caption decoder displays text of audio

transmission for closed caption supported program-

ming.

• MTS/SAP Tuner

- Audio language can be selected from the remote

control.

• Auto Shut Off Function

- Unit turns itself off automatically after 15 minutes

of no operation or no signal input from the antenna

terminal.

• Screen Saver

- The screen saver program starts when there is no input

from the unit for 5 minutes in stop mode.

• Subtitles in a Desired Language

- You can select a desired language for the display sub-

titles, if that language is available on a disc.

• Selecting a Camera Angle

- You can select the desired camera angle, if a disc con-

tains sequences recorded from different angles.

• Choices for On-Screen Menu Language

- Select your setup menu language: English, Spanish or

French.

• Choices for Audio Language and Sound Mode

- Select your desired language or sound mode when

different options are available on your disc.

• Parental Lock

- Block the viewing of discs unsuitable for children.

• Automatic Detection of Discs

• Choices for On-Screen Menu Language

- Select your setup menu language: English, Spanish or

French.

• Stereo Sound Function

• Full-Function Remote Control

• PLL Frequency Synthesized Tuning

• HDMI Input

- This TV accepts 480i / 480p / 720p / 1080i video signals

and 32kHz / 44.1kHz / 48kHz audio signals.

• Component VIDEO Input

- This TV accepts 480i / 480p / 720p / 1080i video signals.

• S-VIDEO Input

• AV Input

- This unit automatically detects if the loaded disc is

DVD, Audio CD or CD-RW/-R with MP3 or JPEG files.

• On-Screen Display

- Displays current information regarding TV operations

(such as program playback). This function is accessible

by remote control.

• Analog Audio Output

• Digital Audio Output (Coaxial)

• Search

- Chapter search / Title search / Track search / Time

• Repeat

- Chapter / Title / Track / Group / All / A-B

• Zoom

- Allows you to enlarge video image.

• Marker

- The part designated by user can be called back.

• Resume Play

- Lets you resume play from where you left off.

• Virtual Surround

• Bit Rate Indication

• DRC (Dynamic range control)

- You can control the range of sound volume.

Download from Www.Somanuals.com. All Manuals Search And Download.

5REMOTE CONTROL FUNCTION

1. INPUT SELECT button (p19)

19. CLEAR button (p35 / p36)

• To clear the numbers entered incorrectly.

• To cancel the point A for A-B repeat (DVD, CD).

• To remove track number in program input

(CD, MP3, JPEG).

Press to access connected external devices like

a DVD recorder or VCR.

2. POWER button (p13)

Press to turn TV/DVD on and off.

3. Number buttons (p17)

• Press to select a channel.

• Press to input number of title, chapter or track.

4. SETUP button (p21)

Press to display on-screen menu.

5. ENTER button (p13)

20. REPEAT button (p35)

To play a chapter or title (DVD), track, disc (CD,

MP3, JPEG) or group (MP3, JPEG) repeatedly.

21. A-B button (p36)

To repeat between your chosen point A and B

(DVD, CD).

Press to confirm your selection.

22. TITLE button (p30)

buttons (p13)

To call up the title menu (DVD).

23. PLAY B button (p30)

To begin disc playback.

To move left/ right/ up/ down through the

items.

7. BACK/RETURN button (p19)

24. STOP C button (p30)

To stop disc playback.

Press to return to previous menu operation.

8. CH RETURN button (p17)

25. REV E / FWD D buttons (p31)

To begin slow forward or slow reverse playback

during the pause mode (DVD) and search for-

ward or backward through a disc.

26. CH K/L buttons (p17)

To select channels and external input mode.

27. INFO button (p19 / p37)

• Analog mode (TV)

Press to return to previously viewed channel.

9. VOL.

buttons (p17)

Press to adjust volume.

10. MUTE button (p17)

Press to turn sound off and on.

11. SKIP H / G buttons (p34)

To skip forward or backward chapters, titles (DVD),

tracks (CD, MP3, JPEG) or folders (MP3, JPEG).

To display channel No., signal type and TV

setting.

11 12. PAUSE button (p30)

To pause disc playback.

• Digital mode (DTV)

13. DISC MENU button (p30 / p32)

To display channel information, signal type

and TV setting.

To call up the menu on a disc (DVD) or FILE

LIST (MP3, JPEG).

• External input mode

21 14. MODE button (p33 / p36 / p38)

To display external input mode, signal type

and TV setting.

• To call up the FOLDER LIST on a disc when

“Dual Playback“ is “ON“ (MP3, JPEG).

• To arrange the playing order or play randomly

(CD, MP3, JPEG).

• DVD mode

To display the current status (DVD, CD, MP3,

JPEG).

• To set black level (DVD) and virtual surround

(DVD, CD, MP3) on or off.

28. SCREEN MODE button (p20)

To select aspect ratios available for the screen.

29. SLEEP button (p21)

15. SEARCH MODE button (p34)

• To search chapter, title (DVD), time (DVD, CD)

or track (CD, MP3, JPEG).

Press to activate the sleep timer.

30. AUDIO button (p18 / p39)

• Analog mode (TV)

16. SUBTITLE button (p38)

To select subtitles on a disc (DVD).

17. ANGLE button (p38)

Selects audio mode.

• Digital mode (DTV)

To change the camera angle to see the

sequence being played back from different

angle (DVD).

Selects audio language.

• DVD mode

Selects audio language (DVD) or sound

mode (CD).

18. ZOOM button (p31)

To magnify the part of picture (2X and 4X: DVD, 31. EJECT button (p30)

2X: JPEG).

To eject the disc.

NOTE:

• With buttons [VOL. X/Y] or [MUTE], you can only adjust the volume of the main unit. You cannot adjust the volume of the external devices

with these buttons.

• Unless stated, all operations described are based on remote control use.

5INSTALLING THE BATTERIES

Install two AA batteries (included) matching the polarity (++/--) indicated inside battery compartment of the remote control.

BATTERY PRECAUTIONS:

• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.

• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones.

• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

Download from Www.Somanuals.com. All Manuals Search And Download.

NTRODUCTION

5CONTROL PANEL

1. SETUP button (p21)

To display on-screen menu.

2. STOP C button (p30)

To stop disc playback.

3. PLAY B button (p30)

DVD CONTROL

STOP

PLAY

SKIP

EJECT

To begin disc playback.

4. SKIP H / G buttons (p34)

To skip chapters, titles (DVD) or tracks (CD, MP3 or JPEG).

5. EJECT A button (p30)

INPUT SELECT/

ENTER

SETUP

POWER

VOLUME

CHANNEL

TV CONTROL

To eject the disc.

6. POWER button (p13)

To turn TV/DVD on or off.

7. INPUT SELECT/ENTER button (p19/p13)

• To access connected external devices like a DVD recorder

or VCR.

• To decide the command of setting when the menu is displayed.

8. CHANNEL

buttons (p17)

To select channels and move up/down through the menu items.

9. VOLUME

buttons (p17)

To adjust volume and move right( )/left( ) through the

menu items.

10. Infrared Sensor Window

Receives infrared rays transmitted from the remote control.

STANDBY

POWER ON

NOTE:

• With buttons [VOLUME X/Y], you can only adjust the volume

of the main unit. You cannot adjust the volume of the external

devices with these buttons.

5REAR PANEL

1. ANT. IN jack (p9)

Coaxial cable connection for your antenna or cable box.

2. DIGITAL AUDIO OUT (COAXIAL) jack (p12)

Digital audio coaxial cable connection for decoder or audio

receiver. Connect cable to DIGITAL AUDIO IN jack of external

device.

3. AUDIO OUT jacks (p12)

Audio cable connection for external audio equipment. Use

AUDIO IN jacks of external equipment.

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

4. AUDIO input jacks (for DVI connection) (p10)

Audio cable connection for external audio/video devices

with DVI jack. Use AUDIO OUT jacks of external equipment

when using an HDMI-DVI conversion cable.

5. HDMI IN jack (p10)

HDMI

from underneath

Rear of this TV

VIDEO

AUDIO

VIDEO

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

ANT. IN

AUDIO OUT AUDIO

AUDIO

S-VIDEO1

S-VIDEO2

HDMI cable connection for external video equipment (i.e.

DVD recorder).

HDMI IN

HDMI

COMPONENT2

COMPONENT1

VIDEO1

INNER JACKS

6. S-VIDEO1 input jack (p11)

S-Video cable and audio ( in VIDEO1 terminal) cable connec-

tion for external video equipment.

7. S-VIDEO2 input jack (p11)

from underneath

S-Video cable and audio ( in VIDEO2 terminal) cable connec-

tion for external video equipment.

VIDEO

8. VIDEO1 and AUDIO input jacks (p12)

Video and audio cable connection for external equipment.

9. VIDEO2 and AUDIO input jacks (p12)

Video and audio cable connection for external equipment.

10. COMPONENT1 and AUDIO input jacks (p11)

Component cable connection for external audio/video

devices. Use component and audio out jacks of external

device.

11. COMPONENT2 and AUDIO input jacks (p11)

Component cable connection for external audio/video

devices. Use component and audio out jacks of external

device.

S-VIDEO1

S-VIDEO2

AUDIO

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

Download from Www.Somanuals.com. All Manuals Search And Download.

REPARATION

5CONNECTION

This section describes how to connect your TV to an antenna, cable box, etc.

MAKE SURE YOU HAVE AN ANTENNA.

As DTV is only available over the air, you need an antenna to receive a digital signal.

NOTE:

• Be sure your antenna or other source is connected properly before plugging in the power cord.

[ANTENNA CABLE CONNECTION]

1) When connecting your TV to an antenna

Connect the coaxial cable on your home outlet to the ANT. IN jack of this TV.

2) When connecting TV to Cable TV company (without box)

Connect the coaxial cable on your home outlet to the ANT. IN jack of this TV.

VHF / UHF

antenna

Rear of this TV

Coaxial cable

(not included)

ANT. IN

VIDEO

AUDIO

VIDEO

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

AUDIO OUT AUDIO

AUDIO

S-VIDEO1

S-VIDEO2

HDMI IN

HDMI

COMPONENT2

COMPONENT1

VIDEO1

INNER JACKS

Coaxial cable

Cable TV

company

(not included)

*Once connections are completed, turn on the TV and begin initial setup.

Channel scanning is necessary for the TV to memorize all available channels in your area.

(Refer to “INITIAL SETTINGS” on page 13.)

NOTE:

• For your safety and to avoid damage to equipment, please unplug the coaxial cable from the ANT.IN jack before moving the unit.

• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than set-

top versions.

• To easily switch your reception source between antenna and cable, install an antenna selector (not included).

• If you connect to the cable system directly, contact the CATV installer.

[CONNECTION TO CABLE BOX or SATELLITE BOX]

1) Connect the coaxial cable on your home outlet to the input jack of the CABLE/SATELLITE box.

2) Use another coaxial cable to connect the ANT. IN jack of your TV to the output jack of the CABLE/SATELLITE box.

EX.

Rear of this TV

Satellite

dish

Cable box or

Satellite box

VIDEO

AUDIO

VIDEO

AUDIO

ANT.

DIGITAL

AUDIO OUT

(COAXIAL)

Coaxial cable

ANT. IN

AUDIO OUT AUDIO

AUDIO

S-VIDEO1

S-VIDEO2

HDMI IN

HDMI

COMPONENT2

COMPONENT1

VIDEO1

INNER JACKS

Cable TV

company

(not included)

*Required cables in 2) and connecting methods differ depending on the CABLE/SATELLITE box.

For more information, please contact your cable/satellite provider.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPARATION

5CONNECTING OTHER DEVICES

[HDMI]

1) High Definition Multimedia Interface (HDMI) uses the latest technology to ensure the signal maintains the highest

degree of integrity from source to TV. Both video and audio travel through a single cable.

HDMI cable

To HDMI IN jack

(not included)

EX.

HDMI OUT

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

To HDMI output jack

DVD recorder with the HDMI output jack

HDMI

Rear of this TV

NOTE:

• This TV accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.

• This TV accepts only 2 channel audio signal (LPCM).

• You need to select “PCM” for the digital audio output of the device you connect or the HDMI audio setting. Audio sometimes makes no

sound if you select “Bitstream”, etc.

• This TV only accepts signals corresponding EIA861.

2) When your video device has a DVI output jack, connect the HDMI conversion cable (not included) from the DVI out-

put jack.

HDMI-DVI conversion cable

(not included)

To HDMI IN jack

To DVI output jack

EX.

DVI OUT

ANT. IN

AUDIO OUT

AUDIO

AUDIO OUT

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

Cable box or Satellite box

with the DVI output jack

HDMI

To audio

output jacks

To AUDIO

input jacks

Rear of this TV

Audio cable

(not included)

NOTE:

• This TV accepts 480i / 480p / 720p / 1080i video signals.

• An HDMI conversion cable requires a separate audio cable connection as well.

• Audio signals are converted from digital to analog if you make the connection in paragraph 2) above.

• DVI does not show image if the 480i does not accept EIA/CEA-861/861B.

“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks

or registered trademarks of HDMI Licensing LLC.”

Download from Www.Somanuals.com. All Manuals Search And Download.

[COMPONENT CABLE CONNECTION]

Offers better picture quality for video devices connected to your TV.

Use a component video cable (not included) to connect your TV to external video devices equipped with component

video jacks.

If you connect to your TV’s COMPONENT1 input jack, connect audio cables to the AUDIO L/R jacks of COMPONENT1.

If you connect to your TV’s COMPONENT2 input jack, connect audio cables to the AUDIO L/R jacks of COMPONENT2.

Component video cable

(not included)

To COMPONENT1

input jacks

To component

video output jacks

VIDEO

EX.

S-VIDEO1

S-VIDEO2

DVD Recorder with the component

video output jacks

AUDIO

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

To audio

output jacks

Rear of this TV

To AUDIO

input jacks

Audio cable

(not included)

NOTE:

• This TV accepts 480i / 480p / 720p / 1080i video signals.

[S-VIDEO CABLE CONNECTION]

Offers good picture quality for video devices connected to your TV.

Use an S-video cable (not included) to connect your TV to external video devices equipped with S-video connectors.

If you connect to your TV’s S-VIDEO1 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO1.

If you connect to your TV’s S-VIDEO2 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO2.

To S-VIDEO1

input jack

S-Video cable

(not included)

To S-Video

output jack

VIDEO

EX.

AUDIO

OUT

VIDEO S-VIDEO

OUT OUT

S-VIDEO1

S-VIDEO2

AUDIO

DVD Recorder with

the S-Video output jacks

To audio

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

output jacks

To AUDIO

input jacks

Rear of this TV

Audio cable

(not included)

NOTE:

• If you connect to the S-Video jack and the VIDEO jack at the same time, the S-Video connection will have priority.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPARATION

[VIDEO CONNECTION]

Offers standard picture quality for video devices connected to your TV.

When the audio jack of the video device is monaural, connect the audio cable to the audio L input jack.

If you connect to your TV’s VIDEO1 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO1.

If you connect to your TV’s VIDEO2 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO2.

Video cable

To VIDEO1

input jack

(not included)

EX.

To video

VIDEO

output jack

AUDIO

OUT

VIDEO

OUT

S-VIDEO1

S-VIDEO2

Camcorder

Video Game

AUDIO

To audio output

jacks

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

VCR

To AUDIO Rear of this TV

input jacks

Audio cable

(not included)

[DIGITAL AUDIO OUTPUT CONNECTION]

If you connect this TV to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital broad-

casting sound. Required digital audio coaxial cable not included.

EX.

Digital audio coaxial cable

(not included)

To DIGITAL AUDIO

OUT jack

MD deck, DAT deck, etc.

COAXIAL

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

To coaxial digital

audio input jack

HDMI

Rear of this TV

Dolby Digital decoder

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D

symbol are trademarks of Dolby Laboratories.

[ANALOG AUDIO OUTPUT CONNECTION]

If you connect this TV to an external analog audio device, you can enjoy stereophonic (2 channel) audio sound.

Required audio cable not included.

AUDIO

EX.

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

To audio

input jacks

HDMI

Stereo system

Rear of this TV

To AUDIO

OUT jacks

Audio cable

(not included)

Download from Www.Somanuals.com. All Manuals Search And Download.

ETTING TV

TV FUNCTIONS

NOTE:

5INITIAL SETTINGS

• The initial Autoscan function can be executed for either “Air”

or “Cable” only once. When you change the connection (Air/

Cable), set the “Autoscan” again. (Refer to page 14.)

This section will guide you through your TV’s initial set up which includes

selecting a language for your on-screen menu and AUTOSCAN, which

automatically scans and memorizes viewable channels.

• If you connect to the cable system directly, contact the CATV

installer.

• When the scanning is not complete, Helpful Hint will be dis-

played every time you turn on the power. If you have previ-

ously registered channels when this screen appears, you can

access them with [the Number buttons].

After making all the necessary connections, turn on

your TV.

Press [POWER] to display the Initial Setup menu.

2-0

No channel is registered.

Press and hold "ENTER" key for 3 seconds.

Contact support hotline provided on manual or back of unit.

• This operation may take a few moments.

• If Initial Setup menu does not appear, press and hold

[ENTER] for 3 seconds, initial setup will appear then

proceed to step 3.

Sin canal registrado.

Mantenga oprimida la tecla "ENTER" durante 3 segundos.

Llame teléfono de apoyo en manual o atrás de TV.

Pas de chaîne consign.

Maintenir la touche "ENTER" pressée 3 secondes.

Contacter numero d'urgence dans manuel ou arrière appareil.

If initial set up has already been completed, refer to

“LANGUAGE SELECTION” on page 16.

• Toll free customer support line can be found on the cover of

this manual.

When you first turn on your TV, the following screen is

displayed. Use [

] to select the on-screen menu lan-

guage from the choices on the right side of the screen.

(English / Español / Français)

Initial Setup

Select the language for setup display.

Elija idioma de preparación.

English

Español

Français

Sélectionner langue écran config.

^SETUPExit

ENTER

Select

Enter

• The Antenna Confirmation menu on step 4 will be

displayed in the selected language after you press

[ENTER].

Use [

] to select source of ANT. IN jack, then press

[ENTER].

Initial Setup

Make sure the antenna is connected to "ANT IN" jack.

Select the destination of "ANT IN" jack.

Air

Cable

Air

Cable

ANT IN

BACK

ENTER

Select

Enter

Back

^SETUPExit

Autoscan will start automatically.

Initial Setup

Now the system is scanning for channels,please wait.

Analog channels

Digital channels

1ch

0ch

^SETUPExit

• When scanning has completed, the lowest memorized

channel will be displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

ETTING TV

5AUTOSCAN

• When the scanning and memorizing are completed,

the lowest memorized channel in the broadcasting

will be displayed.

With AUTOSCAN, your TV automatically scans and memorizes your area’s

viewable channels. Activate AUTOSCAN when you turn on your TV for the

ﬁrst time, change broadcast sources (e.g. from antenna to CATV), or move

your TV to a diﬀerent broadcast area.

NOTE:

• Make sure the TV is connected to antenna or cable.

• If you connect the cable system directly, contact the CATV

Press [SETUP] to display the setup screen.

installer.

EXIT

• If you press [POWER] or [SETUP] during Autoscan, this set-

ting will be canceled.

PICTURE

• If there is no reception or a poor signal is detected, once

scanning stops and a Helpful Hint will appear on screen.

CHANNEL

DETAIL

LANGUAGE

DVD

Use [

] to select “CHANNEL”, then press [ENTER].

Use [

] to select “Autoscan”, then press [ENTER].

Channel

EXIT

Autoscan

PICTURE

Channel List

Manual Register

CHANNEL

Antenna

DETAIL

LANGUAGE

DVD

Use [

] to select “Air” for TV channels or “Cable“ for

CATV channels, then press [ENTER].

Autoscan

EXIT

Back

Air

Autoscan will rescan all channels.

PICTURE

This may take a while to complete.

Select the destination of "ANT IN" jack.

Cable

CHANNEL

Cable

1hour

Air

DETAIL

LANGUAGE

DVD

Cable

ANT IN

• Scanning and memorizing the channels automatically

starts.

Now the system is scanning for channels, please wait.

72%

Analog channels

Digital channels

10ch

6ch

^SETUPExit

Download from Www.Somanuals.com. All Manuals Search And Download.

5CHANNEL LIST

5MANUAL REGISTER

This function lets you remove undesired channels from the Channel

Registration List.

This function lets you manually add channels not memorized due to poor

broadcast strength during AUTOSCAN.

Press [SETUP] to display the setup screen.

EXIT

PICTURE

CHANNEL

DETAIL

CHANNEL

DETAIL

LANGUAGE

DVD

LANGUAGE

DVD

Use [

] to select “CHANNEL”, then press [ENTER].

Use [

] to select “CHANNEL”, then press [ENTER].

Use [

] to select “Channel List”, then press [ENTER].

Use [

] to select “Manual Register”, then press

Channel

[ENTER].

EXIT

Autoscan

Channel

PICTURE

EXIT

Channel List

Autoscan

Manual Register

CHANNEL

PICTURE

Channel List

Antenna

Manual Register

DETAIL

CHANNEL

Antenna

LANGUAGE

DVD

DETAIL

LANGUAGE

DVD

Use [

] to select the channel you want to remove.

Channel List

Use [the Number buttons] to select the channel you

EXIT

Highlight channels for

Ch Up/Down key selection.

DTV

want to add, then press [ENTER].

PICTURE

CHANNEL

DETAIL

DTV

Manual Register

EXIT

LANGUAGE

DVD

DTV

For Analog channels,

select a channel to register

using number keys.

PICTURE

BACK

ENTER

Ch Select

Watch/Skip

Back

For Digital channels,

you must perform Autoscan function.

CHANNEL

DETAIL

LANGUAGE

DVD

• Press [ENTER] to highlight the channel selected for

BACK

Back

Ch Change

removal. You will not be able to select the channel

again using [CH

• To reactivate the removed channel, highlight it and

press [ENTER].

• When you remove a major channel, you remove its

minor channels, too.

To exit the setup, press [SETUP].

NOTE:

• The channel with “DTV” indicated on the display is ATSC,

otherwise the channel is NTSC.

NOTE:

• If set up completes successfully, “Registered to the Channel

List” is displayed.

• If Video 1 is being used, set up will not be completed suc-

cessfully and “Unavailable” will be displayed on the screen.

• In the DTV broadcasting, one channel sometimes broad-

casts multiple programs depending on the air time. In this

case, the main channel is called major channel and the

minor channel is called minor channel.

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

ETTING TV

5ANTENNA CONFIRMATION

5LANGUAGE SELECTION

Displays signal strength for each channel.

You can choose English, Spanish, or French as your on-screen menu

language.

Press [SETUP] to display the setup screen.

EXIT

PICTURE

CHANNEL

DETAIL

CHANNEL

DETAIL

LANGUAGE

DVD

LANGUAGE

DVD

Use [K /L] to select “CHANNEL”, then press [ENTER].

Use [K /L] to select “LANGUAGE”, then press [ENTER].

Use [K /L] to select “Antenna”, then press [ENTER].

Use [K /L] to select your language, then press [ENTER].

Channel

EXIT

Autoscan

Language

PICTURE

EXIT

Channel List

Manual Register

English

Español

Français

Select the language for setup display.

Elija idioma de preparación.

CHANNEL

PICTURE

Antenna

DETAIL

CHANNEL

DETAIL

Sélectionner langue écran config.

LANGUAGE

DVD

LANGUAGE

DVD

• Use [the Number buttons] or [CH K /L] to select the

channel for which you want to check signal strength.

To exit the setup, press [SETUP].

Antenna

EXIT

Back

PICTURE

CHANNEL

Now

70 Peak

DETAIL

LANGUAGE

DVD

Ch Change

• If the channel is set to external input, you cannot con-

firm the antenna situation.

Video1

Antenna

EXIT

Back

PICTURE

CHANNEL

Indicator is available

for antenna signal only.

DETAIL

LANGUAGE

DVD

Ch Change

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING TV

5CHANNEL SELECTION

5VOLUME ADJUSTMENT

Select channels by pressing [CH K/L] found on remote control or

[CHANNEL K/L] on the TV’s control panel, or by pressing [the Num-

ber buttons] found on the remote control.

This section describes how to adjust the volume. The mute function, which

turns the sound oﬀ and on, is also described.

[CH /L]

[VOL.

]

Use [CH /L] to change the channel.

Use [VOL.

] to adjust the audio volume.

Volume

• The same operation is available with [CHANNEL K/L]

on the control panel of the main unit.

• The volume bar will be displayed at the bottom of the

screen when adjusting the volume.

• The volume bar display will automatically disappear in

a few seconds.

• The same operation is also available with [VOLUME

[the Number buttons]

Press the channel number with [the Number buttons] to

select a channel you want to watch, then press [ENTER].

X/Y] on the control panel of the main unit.

[MUTE]

Press [MUTE] to turn off and on the sound.

- When selecting analog channel 12

Mute

ENTER

• “Mute” is displayed on the screen for a few seconds.

- When selecting digital channel 12-1

Be sure to press [–] before entering the minor chan-

X Y

Press [MUTE] again or [VOL.

] ([VOLUME X/Y]) to

release the Mute status.

nel number.

ENTER

• If the channel broadcasts NTSC and ATSC both and

you do not press [–], you will receive the NTSC chan-

nel only. The moment you press [–], the lowest mem-

orized digital channel will be displayed.

• Press [CH RETURN] to return to the previously viewed

channel.

NOTE:

• In DTV broadcasting, one channel sometimes broadcasts

multiple programs depending on the air time. In this case,

the main channel is called major channel and the minor

channel is called minor channel.

About minor channel broadcasting:

There may be different programs being broadcast on

minor channels through a single channel from ATSC.

You can watch each minor channel program being

broadcast by selecting one of the minor channels.

NTSC

ATSC

18:00

18:30

19:00

19:30

20:00

CH4-1 No signal No signal

CH4-1 CH4-2 CH4-3

CH4

CH4-1 No signal CH4-3

CH4-1 CH4-2 No signal

: change automatically

: change manually by using [CH / ]

NOTE:

• “No Signal” will appear on the screen after the minor chan-

nel broadcast is over.

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING TV

5SELECTING AUDIO CHANNELS

This section describes how to switch the audio in the analog mode and how

to switch the audio language in the digital mode.

DTV

Press [AUDIO] to display the currently selected lan-

guage and the number of available languages.

Press [AUDIO] to display the currently selected audio

mode.

6-1

English 1/3

SAP / STEREO

Press [AUDIO] to cycle through available audio lan-

guages.

Press [AUDIO] to cycle through available audio chan-

nels.

• When the broadcasting has all audio...

English 1/3

Spanish 2/3

SAP / STEREO

Other 3/3

SAP / MONO

• Available languages differ depending on the broad-

cast.

• When the broadcasting has stereo and monaural

audio...

• The information display will automatically disappear

in 1 minute.

MONO / STEREO

NOTE:

• Pressing [AUDIO] does not control external audio source.

• When the broadcasting has SAP and monaural audio...

SAP / MONO

• When the broadcasting has only monaural audio...

MONO

(The audio cannot be switched.)

STEREO

SAP

MONO

: Outputs stereo-audio

: Outputs second audio program

: Outputs mono-audio

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSING EXTERNAL DEVICES 5SCREEN INFORMATION

Use your remote control to access DVD recorders, home audio systems and

other external devices when they are connected to your television.

You can display the currently selected channel or other information such as

the audio mode on the screen.

In the analog mode, the current channel and the audio mode are displayed.

Press [INFO].

Use your remote control to select external component.

• When you press [INPUT SELECT] or [CH ] on the

remote control, the Input Mode will be switched as

below.

SAP / STEREO

480i SD

4:3

TV-PG DLSV

TV/DTV channel

• The current channel number, audio mode, type of

resolutions for video signal, TV aspect ratio, CC and TV

rating are displayed at the top-right of the screen.

• To clear the display, press [BACK/RETURN] or [INFO]

again.

Video1

Video2

DTV

Component1

In the digital mode, the detailed information for the current channel such

as the Program guide is displayed.

Component2

HDMI

Press [INFO].

• The following information is displayed.

(1) Program title

(2) Broadcast station

(3) Program guide (max. 4 lines displayed)

(4) Channel number

(5) Audio language (“Other”is displayed when the audio

language cannot be acquired, or the acquired lan-

guages are other than English, Spanish or French.)

(6) Effective scanning lines and scan mode

(7) Program definition

• Pressing [CH ] on the remote control reverses direc-

tion.

• To use the VIDEO1 or S-VIDEO1 input jack on the TV,

select “Video1”.

• To use the VIDEO2 or S-VIDEO2 input jack on the TV,

select “Video2”.

• To use the COMPONENT1 input jacks on the TV, select

“Component1”.

• To use the COMPONENT2 input jacks on the TV, select

“Component2”.

(8) Program aspect ratio

(9) Program rating

(10) CC (not available if the CC set to “Off”)

• To use the HDMI IN jack on the TV, select “HDMI”.

• The information display will automatically disappear

in 1 minute.

(1)

(2)

(4)

A Day of Memories

KABC

6-1

English 1/2

A quarter-century ago,which may now qualify as the

good old days of newspapering,run-of-paper sales

accounted for 80 percent of the industry's advertising

revenues.Department stores and supermarket were

(5)

1080i HD 16:9

TV-PG DLSV

(6), (7), (8)

(3)

(9) (10)

NOTE:

• When the program guide consists of more than 4 lines, use

[K/ L] to scroll.

• “No description provided” is displayed when the program

guide is not provided.

• In external input mode, the following screen is displayed:

e.g.) If the external device is connected to VIDEO1 input

jacks

Video1

480i SD

TV-PG DLSV

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING TV

CHANGING THE SCREEN DISPLAY MODE

Each of four display modes can be selected in either 4:3 or 16:9 aspect ratios.

Press [SCREEN MODE] to switch the TV aspect ratio.

Press [SCREEN MODE] repeatedly to return to the nor-

mal screen displays.

NOTE:

• Some programs may not offer all display mode options.

• When the broadcast is sending 4:3 video signal:

• When the broadcast is sending 16:9 video signal:

Sidebar

Full

Zoom

(normal)

Wide

Cinema

Expand

Cinema

[Sidebar]

[Full]

Sidebar displays a 4:3 picture at its standard 4:3 size.

Sidebars will be displayed on the right and left edges

of the screen.

A picture is displayed at 16:9 size as it is.

[Zoom]

Zoom displays a 16:9 picture without changing its

horizontal and vertical ratio, at its maximum size.

[Full]

Full displays a 4:3 picture at a 16:9 size, with horizontal

elongation necessary to fill the screen.

[Cinema]

Cinema displays a 16:9 picture with vertical elonga-

tion.

[Cinema]

Cinema displays a 4:3 picture at a 16:9 size, with less

horizontal elongation necessary to fill the screen

because a little bit of the top and bottom edge of the

screen will be cut off.

[Expand]

Expand displays a 16:9 picture with horizontal elonga-

tion.

[Wide]

Wide displays the center of the picture as original size

and the outer sides of the picture will be elongated. The

size of the picture will depend on the original signal.

Download from Www.Somanuals.com. All Manuals Search And Download.

5SLEEP TIMER

5SETUP SCREEN

The Sleep Timer can be set to automatically turn oﬀ your television after an

incremental period of time.

This section describes the overview of the setup screen displayed when you

press [SETUP].

For more details, see the reference page for each item.

The setup screen consists of the function setting items below.

Press [SLEEP] on the remote control to set the Sleep

Timer.

Press [SETUP].

Sleep

Off

• The setting display for Sleep Timer is shown on the

screen.

EXIT

To exit settings.

You can set your TV to turn off after a set period of time

(from 10 to 90 minutes). After set up, you can display

the remaining time before shut off by pressing [SLEEP]

again.

• To cancel the sleep timer, press [SLEEP] repeatedly

until “Sleep Off” is displayed.

PICTURE

You can adjust the picture quality (Picture Mode,

Brightness, Contrast, Color, Tint, Sharpness, Color

Temp., and Energy Saving).

(Refer to “PICTURE ADJUSTMENT” on page 22.)

Sleep

Off

CHANNEL

• The Sleep Timer setting display will automatically dis-

appear in a few seconds.

You can automatically scan the viewable channels and

remove those that are undesired.

(Refer to “AUTOSCAN” on page 14.)

NOTE:

• When you disconnect your TV from its power source or

when a power failure occurs, the sleep timer setting will be

canceled.

DETAIL

You can change closed captioning display formats and

font styles.

(Refer to “CLOSED CAPTION” on page 23.)

Block children’s access to programming.

(Refer to “V-CHIP” on page 26.)

And select HDMI Audio if your TV is connected to a

digital external device like a DVD recorder.

(Refer to “HDMI AUDIO” on page 28.)

LANGUAGE

You can change the language (English, Spanish,

French) displayed on the setup screen.

(Refer to “LANGUAGE SELECTION” on page 16.)

DVD

You can change the setup of built-in DVD player. Make

sure the unit is in DVD mode and the player is in stop

mode.

(Refer to “SETTING DVD” on page 40.)

NOTE:

• To cancel the setup screen, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING TV

Color

Tint

Use [s / B] to adjust Color to be bril-

5PICTURE ADJUSTMENT

liant or pale.

You can select from four default picture color settings. You can also adjust

brightness, contrast, color, tint, sharpness and color temperature as well as

energy saving settings.

s: To pale

B: To brilliant

Color

ENTER

Adjust

Move

Enter

Press [SETUP] to display the setup screen.

Use [s / B] to adjust Tint to be obtained

EXIT

natural skin tones.

PICTURE

s: To red

B: To green

CHANNEL

DETAIL

Tint

Adjust

LANGUAGE

DVD

ENTER

Move

Enter

Sharpness

Use [s

picture.

s: To soft

B] to adjust the detail of the

Use [K /L] to select “PICTURE, then press [ENTER].

B: To clear

Sharpness

ENTER

Adjust

Move

Enter

Reset Settings Use [K /L] to select “Reset”. So you can

reset the Picture Mode as the factory

default.

Use [K /L] to select the picture quality you want to

adjust, then press [ENTER].

Picture

EXIT

Reset Settings

Dynamic

Picture Mode

Brightness

Contrast

EXIT

PICTURE

This function resets the

"Dynamic" setting for Picture Mode

to factory default.

Cancel

Reset

PICTURE

CHANNEL

DETAIL

Color

CHANNEL

DETAIL

Tint

Sharpness

Reset Settings

Color Temp.

Energy Saving

LANGUAGE

DVD

Neutral

LANGUAGE

DVD

Off

Color Temp. Use [K /L] to adjust Color Temperature

from the selection, then press [ENTER].

(Cool, Neutral and Warm)

Adjust your desired Picture as you prefer.

Picture Mode Use [K /L] to select Picture Mode from

Picture

the selection, then press [ENTER].

EXIT

Picture Mode

(Standard, Dynamic, Movie and News)

PICTURE

Brightness

Contrast

Picture

CHANNEL

EXIT

Color

Picture Mode

Brightness

Contrast

Standard

Dynamic

Movie

Tint

DETAIL

PICTURE

Sharpness

LANGUAGE

DVD

Reset Settings

Color Temp.

Cool

CHANNEL

DETAIL

Color

News

Neutral

Warm

Tint

Energy Saving

Sharpness

Reset Settings

Color Temp.

Energy Saving

LANGUAGE

DVD

Energy Saving Use [s / B] to adjust brightness of

backlight.

Brightness

Use [s / B] to adjust until the darkest

parts of the picture are as bright as you

prefer.

s: To dark

B: To bright

Energy Saving Off

Adjust

ENTER

Enter

s: To decrease brightness

B: To increase brightness

• The adjustment bar for picture quality item is dis-

played on the screen.

Brightness 30

ENTER

Adjust

Move

Enter

NOTE:

• To cancel the picture adjustment, press [SETUP].

Contrast

Use [s / B] to adjust Contrast to be

increased or decreased.

s: To decrease contrast

B: To increase contrast

To exit the setup, press [SETUP].

Contrast

ENTER

Adjust

Move

Enter

Download from Www.Somanuals.com. All Manuals Search And Download.

5CLOSED CAPTION

You can view closed captioning (cc) for TV programs, movies, news, and

prerecorded tapes. Closed captions refer to text of dialogue or descriptions

displayed on-screen for the hearing impaired.

Use [K /L] to select the desired closed caption mode,

then press [ENTER].

Closed Caption

EXIT

Conventional CC

DTV CC

Off

PICTURE

CHANNEL

DETAIL

CC1

CC2

CC3

CC4

Text1

Text2

Text3

Text4

CC Style

Press [SETUP] to display the setup screen.

EXIT

LANGUAGE

DVD

PICTURE

CHANNEL

DETAIL

LANGUAGE

DVD

[Caption Mode]

CC1 and Text1:

are the primary caption and text services.

The captioning or text is displayed in the same lan-

guage as the program’s dialogue

(up to 4 lines of script on the screen, where it does not

obstruct relevant parts of the picture).

CC3 and Text3:

serve as the preferred data channels.

The captioning or text is often a secondary language

translation, simplified English or displayed at a slower

rate.

Use [K /L] to select “DETAIL, then press [ENTER].

Use [K /L] to select “Closed Caption”, then press

[ENTER].

Detail

EXIT

CC2, CC4, Text2 and Text4:

Closed Caption

PICTURE

V–chip

are rarely available and broadcasters use them

only in special conditions, such as when CC1 and CC3

are not available or Text1 and Text3 are not available.

Auto

HDMI Audio

CHANNEL

DETAIL

LANGUAGE

DVD

• There are three display modes according to programs:

Paint-on mode: Displays input characters on the

screen immediately.

Pop-on mode : Once characters are stored in memory,

Use [K /L] to select “Conventional CC”, then press

they are displayed all at once.

Roll-up mode : Displays the characters continuously

by scrolling (max. 4 lines).

[ENTER].

Closed Caption

EXIT

Conventional CC

DTV CC

Off

PICTURE

CHANNEL

DETAIL

CC Style

To exit the setup, press [SETUP].

LANGUAGE

DVD

NOTE:

• Closed captions must be broadcast or included in your

recorded content to appear on your TV.

• Closed captions will not be displayed when you are using an

HDMI connection.

• If the closed caption is not in the TV broadcasting, nothing

is displayed.

• When your TV receives a special effects playback signal (i.e.,

Search, Slow and Still) from a VCR’s video output channel

(CH3 or CH4), the TV may not display the correct caption or

text.

• Captions and texts may not match the TV voice exactly.

• Interference may cause the closed caption system not to

function properly.

• The caption or text characters will not be displayed while

the menu display or functions display is shown.

• If a black box appears on the screen, this means that the TV

is set to TEXT mode. To clear screen, select CAPTION “CC1”,

“CC2” , “CC3”, “CC4”or “Off”.

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING TV

5DTV CLOSED CAPTION

5CLOSED CAPTION STYLE

DTV

Apart from closed captions, DTV has its own closed captions called DTV CC.

Use this menu to change the settings for DTV CC.

DTV can also change the style of its Closed Caption such as font, color or

size, etc.

Press [SETUP] to display the setup screen.

EXIT

PICTURE

CHANNEL

DETAIL

CHANNEL

DETAIL

LANGUAGE

DVD

LANGUAGE

DVD

Use [K /L] to select “DETAIL”, then press [ENTER].

Use [K /L] to select “Closed Caption“, then press

Use [K /L] to select “Closed Caption”, then press

[ENTER].

Detail

EXIT

Closed Caption

PICTURE

V–chip

Auto

HDMI Audio

Auto

HDMI Audio

CHANNEL

DETAIL

CHANNEL

DETAIL

LANGUAGE

DVD

LANGUAGE

DVD

Use [K /L] to select “CC Style”, then press [ENTER]

Use [K /L] to select “DTV CC“, then press [ENTER].

Closed Caption

EXIT

Conventional CC

DTV CC

Off

Conventional CC

DTV CC

Off

PICTURE

CHANNEL

DETAIL

CC Style

CHANNEL

DETAIL

LANGUAGE

DVD

LANGUAGE

DVD

Use [K /L] to select “User Setting”, then press [ENTER]

Use [

] to select the desired DTV Closed Caption,

CC Style

then press [ENTER].

EXIT

User Setting

Font Style

Off

Closed Caption

PICTURE

Font0

Middle

White

Solid

Black

Solid

Black

EXIT

Conventional CC

DTV CC

Font Size

CHANNEL

DETAIL

PICTURE

Off

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

CC Style

Service1

Service2

Service3

Service4

Service5

Service6

CHANNEL

DETAIL

LANGUAGE

DVD

LANGUAGE

DVD

None

Off:

Select if you do not want DTV CC. This is the default.

Service 1 to Service 6:

Select one of these before changing any other item

in the Closed Caption menu. Choose “Service1” under

normal circumstances.

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

[Font Opacity]

Font opacity of the displayed caption can be switched

as below.

Use [K /L] to select “On”, then press [ENTER]

CC Style

EXIT

User Setting

Font Style

Off

PICTURE

CC Style

Closed Caption

Font Size

EXIT

CHANNEL

DETAIL

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

User Setting

PICTURE

CHANNEL

DETAIL

LANGUAGE

DVD

Font Style

Font Size

LANGUAGE

DVD

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

Solid

Flash

Translucent

Transparent

Use [K /L] to select the item and switch the setting for

each item you want to set, then press [ENTER]

• When “User Setting” is set to “On”, you can set the

following items. CC style set by “User Setting” will be

displayed.

[Back Color]

Background color of the displayed caption can be

switched as below.

CC Style

Closed Caption

EXIT

User Setting

PICTURE

CHANNEL

DETAIL

LANGUAGE

DVD

Font Style

Font Size

White

Black

Red

• The setting description for each item is shown below.

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

Green

Blue

[Font Style]

Yellow

Magenta

Cyan

Font style of the displayed caption can be switched as

below.

CC Style

Closed Caption

EXIT

[Back Opacity]

Background opacity of the displayed caption can be

switched as below.

User Setting

PICTURE

Font Style

Font Size

CHANNEL

DETAIL

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

CC Style

Closed Caption

LANGUAGE

DVD

EXIT

User Setting

PICTURE

CHANNEL

DETAIL

LANGUAGE

DVD

Font Style

Font Size

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

Solid

[Font Size]

Flash

Translucent

Transparent

Closed Captioning font style can be changed as below.

CC Style

Closed Caption

EXIT

User Setting

PICTURE

Font Style

Font Size

[Edge Color]

Large

CHANNEL

DETAIL

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

Middle

Small

Edge color of the displayed caption can be switched as

below.

LANGUAGE

DVD

CC Style

Closed Caption

EXIT

User Setting

PICTURE

CHANNEL

DETAIL

LANGUAGE

DVD

Font Style

Font Size

White

Black

Red

Font Color

Font Opacity

Back Color

Back Opacity

[Font Color]

Green

Blue

Font color of the displayed caption can be switched as

below.

Yellow

Magenta

Cyan

Edge Color

Edge Type

CC Style

Closed Caption

EXIT

User Setting

PICTURE

Font Style

Font Size

White

[Edge Type]

Black

Red

CHANNEL

DETAIL

Font Color

Font Opacity

Back Color

Back Opacity

Edge Color

Edge Type

Edge type of the displayed caption can be switched as

below.

Green

Blue

LANGUAGE

DVD

Yellow

Magenta

Cyan

CC Style

Closed Caption

EXIT

User Setting

PICTURE

CHANNEL

DETAIL

LANGUAGE

DVD

Font Style

Font Size

Font Color

Font Opacity

Back Color

Back Opacity

None

Raised

Depressed

Uniform

L.Shadow

R.Shadow

Edge Color

Edge Type

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING TV

5VCHIP

A. MPAA Rating

You can block certain programming inappropriate for children. This block

can be released by entering a password.

Use [K /L] to select “MPAA Rating”, then press [ENTER].

V-Chip

EXIT

MPAA Rating

PICTURE

Press [SETUP] to display the setup screen.

TV Rating

New Password

CHANNEL

EXIT

DETAIL

PICTURE

LANGUAGE

DVD

CHANNEL

DETAIL

LANGUAGE

DVD

• The current setting is displayed.

V-Chip

Use [K /L] to select “DETAIL”, then press [ENTER].

EXIT

PICTURE

NC-17

CHANNEL

DETAIL

PG-13

LANGUAGE

DVD

BACK

ENTER

Select

View/Block

Back

Use [K /L] to select “V-chip“, then press [ENTER].

Detail

EXIT

Use [K /L] to select the desired rating, then press

Closed Caption

PICTURE

V–chip

[ENTER] to switch between “View” and “Block”.

Auto

HDMI Audio

CHANNEL

DETAIL

V-Chip

EXIT

PICTURE

LANGUAGE

DVD

NC-17

CHANNEL

DETAIL

PG-13

LANGUAGE

DVD

• The password entry screen is displayed.

BACK

ENTER

Select

View/Block

Back

V-Chip

EXIT

PICTURE

CHANNEL

Enter password.

DETAIL

• The

icon appears when the rating is blocked.

LANGUAGE

DVD

PIN Code

^BACKBack

To exit the setup, press [SETUP].

Use [the Number buttons] to enter the 4-digit num-

bers for your password.

V-Chip

EXIT

PICTURE

CHANNEL

Mature audience only

No one under 17 admitted

Restricted; under 17 requires

accompanying parent or adult

guardian

NC-17

Enter password.

DETAIL

LANGUAGE

DVD

PIN Code

^BACKBack

PG-13

Unsuitable for children under 13

Parental Guidance suggested

General Audience

• When you have not set up your password, enter 0000.

• When the password is correct, the following “V-Chip”

screen is displayed.

No Rating

V-Chip

EXIT

MPAA Rating

PICTURE

TV Rating

NOTE:

New Password

CHANNEL

• When you select a rating and set it to “Block”, the higher rat-

ings will be blocked automatically. The lower ratings will be

available for viewing.

• When you set “X“ to “View”, all ratings turn to “View” auto-

matically.

DETAIL

LANGUAGE

DVD

A. MPAA Rating

B. TV Rating

C. New Password

See the following description for setting each item.

Download from Www.Somanuals.com. All Manuals Search And Download.

B. TV Rating

Fantasy Violence

Violence

Sexual Situation

Coarse Language

Suggestive Dialogue

Use [K /L] to select “TV Rating”, then press [ENTER].

V-Chip

EXIT

MPAA Rating

PICTURE

TV Rating

New Password

CHANNEL

NOTE:

DETAIL

• When you select a rating and set it to “Block”, the higher rat-

ings will be blocked automatically. The lower ratings will be

available for viewing.

LANGUAGE

DVD

• When you set “TV-MA“ to “View”, all ratings turn to “View”

automatically.

• The current setting is displayed.

V-Chip

EXIT

PICTURE

TV-MA

TV-14

CHANNEL

TV-PG

TV-G

TV-Y7

TV-Y

DETAIL

LANGUAGE

DVD

BACK

ENTER

Select

View/Block

Back

Use [K /L / s / B] to select the desired rating, then

press [ENTER].

V-Chip

EXIT

PICTURE

CHANNEL

DETAIL

TV-MA

TV-14

TV-PG

TV-G

TV-Y7

TV-Y

LANGUAGE

DVD

BACK

ENTER

Select

View/Block

Back

• Press [ENTER] to switch between “View” and “Block”

for the rating without sub categories.

V-Chip

EXIT

PICTURE

CHANNEL

DETAIL

TV-MA

TV-14

TV-PG

TV-G

TV-Y7

TV-Y

LANGUAGE

DVD

BACK

ENTER

Select

View/Block

Back

• For the rating with sub categories, use [K /L / s / B]

and select the desired rating, then press [ENTER] to

switch between “View” and “Block”.

To exit the setup, press [SETUP].

Mature audience only

Unsuitable for children under 14

Parental Guidance suggested

General Audience

Appropriate for children 7 and

older

TV-MA

TV-14

TV-PG

TV-G

TV-Y7

TV-Y

Appropriate for all children

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING TV

C. New Password

5HDMI AUDIO

Set the method of sound input for HDMI jack.

Use [K /L] to select “New Password”, then press

[ENTER].

Press [SETUP] to display the setup screen.

V-Chip

EXIT

MPAA Rating

PICTURE

TV Rating

PICTURE

New Password

CHANNEL

DETAIL

LANGUAGE

DVD

LANGUAGE

DVD

Use [K /L] to select “DETAIL”, then press [ENTER].

Press [the Number buttons] on the remote control to

enter the new 4-digit password.

• Enter password again in “Confirm password.” space.

V-Chip

EXIT

PICTURE

CHANNEL

DETAIL

Enter password.

Use [K /L] to select “HDMI Audio“, then press [ENTER].

Confirm password.

Detail

EXIT

Closed Caption

LANGUAGE

DVD

PICTURE

V–chip

Auto

HDMI Audio

PIN Code

^BACKBack

CHANNEL

DETAIL

LANGUAGE

DVD

To exit the setup, press [SETUP].

Use [K /L] to select the desired HDMI audio setting,

NOTE:

• Make sure to enter the exact same new password as the

“Confirm password.”. If they are different, the space is cleared

for reentering.

then press [ENTER].

Detail

EXIT

Closed Caption

PICTURE

V–chip

• Your password will be erased and return to the default

(0000) when a power failure occurs or when you turn off

the power using a wall switch. If you forget the password,

unplug the power cord for 10 seconds to restore the pass-

word to 0000.

HDMI Audio

Auto

CHANNEL

DETAIL

Digital

Analog

LANGUAGE

DVD

• Select “Auto” if you connected to both digital device

with HDMI jack and analog device for audio sources.

Digital audio input signal has priority in this setting.

• Select “Digital” if you connected to digital device with

HDMI jack for digital audio input signal.

• Select “Analog” if you connected to analog device

with analog jacks for analog audio input signal.

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING DVD

DVD FUNCTIONS

5PLAYABLE MEDIA

Recorded

signals

Playable media

Mark (logo)

Region code

Media size

Disc types

DVD-Video

*1, 2, 3, 4, 6, 10

ALL

DVD-RW

DVD-R

* 1, 2, 3, 4, 5,

6, 7, 8, 9, 10

&YBNQMF

5JUMFꢀꢁ

5JUMFꢀꢂ

Digital video

(MPEG2)

12 cm

$IBQUFSꢀꢁ $IBQUFSꢀꢂ $IBQUFSꢀꢃ $IBQUFSꢀꢄ $IBQUFSꢀꢁ

$IBQUFSꢀꢂ

DVD+RW

DVD+R

* 1, 3, 4, 5,

7, 8, 9, 10

Audio CD

Example

Audio CD

* 4, 6, 10

Digital audio

Track 1

Track 2

Track 5

Track 6

Track 3

Track 4

12 cm

Digital audio

.1ꢀ

+1&(

CD-RW

CD-R

* 4, 5, 6, 9,10

MP3

&YBNQMF

(SPVQꢀꢁ

(SPVQꢀꢂ

5SBDLꢀꢁ

5SBDLꢀꢅ

5SBDLꢀꢂ

5SBDLꢀꢆ

5SBDLꢀꢃ

5SBDLꢀꢄ

JPEG

is a trademark of DVD Format/Logo Licensing Corporation.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This unit conforms to the NTSC color system. Discs recorded in other color system such as PAL cannot be played back.

*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.

*3: Discs recorded in VR (Video Recording) format cannot be played back.

*4: Scratched or stained discs may not be played back.

*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or special properties of discs.

*6: You can play back discs which bear the marks above. If you use non-standardized discs, this unit may not play them back. Even if they are

played back, the sound or video quality will be compromised.

*7: Depending on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth,

etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.

*8: Only the discs recorded in the video mode and finalized can be played back. Unfinalized discs cannot be played back. Depending on the

recording status of a disc, the disc may not be played back at all or the picture or sound may not be smooth, etc.

*9: If the recorded portion of the disc is too small (less than 55 mm across), it may not play back properly.

*10: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.

5UNPLAYABLE MEDIA

• NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / DVD-Audio / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL / DTS-CD /

DVD-ROM for personal computers / CD-ROM for personal computers

• On the following disc, the sound MAY NOT be heard.

Super Audio CD

NOTE:

• Only the sound recorded on the normal CD layer can be delivered. The sound recorded on the high density Super Audio CD layer cannot

be delivered.

• Any other discs without compatibility indications

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING DVD

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

5PLAYBACK

5DVD MENU

DVD

MP3

JPEG

DVD

(

on page 32)

Before:

Some DVDs contain menus which allow you to custom-

ize DVD playback.

• Press [DISC MENU] and, use [K / L / s / B] to select

Turn on the ampliﬁer and any other equipment which is connected to this

unit.

Make sure the external audio receiver (not included) are set to the correct

channel.

an item, then press [ENTER] (or [PLAY B]).

Calling up a Menu screen during playback

Press [POWER] to turn on the unit.

• Press [DISC MENU] to call up the DVD menu.

• Press [TITLE] to call up the title menu.

NOTE:

• Menu operations may vary depending on the disc.

Refer to the manual accompanying the disc for more details.

Insert a disc with label facing left from the right side of

the unit.

5RESUME

DVD

MP3

JPEG

label

Press [STOP C] during playback.

Resume message will appear on

the TV screen.

Resume ON

Press 'PLAY' to play from here.

To play the beginning,

press 'STOP' first and then 'PLAY'.

Press [PLAY B] to start resume

playback where you left off.

The unit switches to the DVD mode when the unit was

in TV mode and detects the type of disc.

NOTE:

•

To cancel resume information, press [STOP C] again in the stop

DVD

mode. On some discs, [STOP C] will not work while the resume

message appears. Please wait until the message disappears.

• The resume information will be kept even when unit is in

standby mode. For MP3 and JPEG, playback will resume from

the beginning of the track at which playback was stopped.

e.g.) DVD disc

• Press [PLAY B] if the unit does not go to the DVD

mode.

PAUSED AND STEPBYSTEP PLAYBACK

DVD

MP3

JPEG

The disc starts playback.

Press [PAUSE F] during playback.

• Playback will be paused and sound will be muted.

• Press [PAUSE F] once during Dual/Folder

playback to pause a JPEG file only. Press

[PAUSE F] one more time to pause an MP3

track.

Press [STOP C] to stop playback.

To continue playback, press [PLAY B].

DVD

The disc goes forward one frame at a time.

[PAUSE F] is pressed in the pause mode.

To continue playback, press [PLAY B].

Press [EJECT] to eject the disc.

NOTE:

• Set “STILL MODE” to “FIELD” in the “OTHERS“ setting if pictures

in the pause mode are blurred. (Refer to page 43.)

NOTE:

• When you play an MP3 or a JPEG-format disc, details on page 32.

• A “prohibited icon” may appear at the top-

right on the TV screen when the operation is

prohibited by the disc or this unit.

• Some DVDs may start playback from title 2 or 3 due to specific

programs.

• During the playback of a 2-layered disc, pictures may stop for

a moment. This happens while the 1st layer is being switched

to the 2nd layer. This is not a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

FAST FORWARD / FAST REVERSE 5ZOOM

DVD

MP3

DVD

JPEG

Press [FWD D] or [REV E] repeatedly

during playback to select the required for-

ward or reverse speed.

The zoom function allows you to enlarge the video image

and to pan through the enlarged image.

To continue playback, press [PLAY B].

During playback, press [ZOOM].

NOTE:

• Set “STILL MODE” to “FIELD” in the “OTHERS“ setting if pictures

in the fast playback mode are blurred. (Refer to page 43.)

• Fast forward or reverse search speed is varies with disc.

Approximate speed is 1(2X), 2(8X), 3(20X), 4(50X) and 5(100X)

on DVDs and 1(2X), 2(8X) and 3(30X) on Audio CDs and MP3.

• For Audio CDs and MP3, sound will be output during Fast for-

ward or reverse search.

• The picture becomes twice as large.

5SLOW FORWARD / SLOW REVERSE

DVD

Press [ZOOM] repeatedly to change the required zoom

factor; “x2“, “x4“ or “OFF“.

Use [FWD D] or [REV E] repeatedly

during the pause mode to select the

required forward or reverse speed.

To continue playback, press [PLAY B].

NOTE:

• Slow forward or reverse speed varies with disc. Approximate

speed is 1(1/16X), 2(1/8X) and 3(1/2X).

• Set “STILL MODE” to “FIELD” in the “OTHERS“ setting if pictures

in the slow playback mode are blurred. (Refer to page 43.)

Once a desired zoom factor is set, use [K / L / s / B]

to slide the zoomed picture across the screen.

To exit zoom function, press [ZOOM] repeatedly to

select “OFF“.

NOTE:

• Zooming function does not work while the disc menu is dis-

played.

• 4X zoom is not available on some discs.

• Only 2X zoom is available on JPEG files.

• Zoom function is also available during pause mode.

• Position guide is not available for JPEG files.

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING DVD

This unit recommends the files recorded under the follow-

ing circumstances:

5MP3, JPEG PLAYBACK

MP3

JPEG

Applicable MP3 ﬁle

Remarks

Sampling frequency:

MP3 or JPEG is a method of compressing ﬁles. You can copy MP3 or JPEG

ﬁles on CD-RW/-R discs from the Personal Computer and play the ﬁles on

this unit.

For MP3 file recorded in Variable Bit

Rate (VBR), the unit may not display

the actual elapsed time.

44.1 kHz or 48 kHz

Constant bit rate:

32 kbps ~ 320 kbps

Applicable JPEG ﬁle

Remarks

Insert an MP3 or JPEG-format disc, playback starts

automatically.

• Press [PLAY B] if MP3 or JPEG-format disc is already

inserted.

• Press [DISC MENU] when you want to call up the FILE

LIST.

When selecting the folder:

Normal playback

Upper limit: 6,300 x 5,100 dots

Lower limit: 32 x 32 dots

A JPEG image that extends beyond

the screen is reduced so that it will

be displayed within the screen.

File size:

Max. 7 MB

Dual playback

Upper limit: 5,000 x 5,000 dots

Lower limit: 32 x 32 dots

File size:

Max. 5 MB

• Press [ B] when you want to go to the next hierarchy.

FILE LIST

DISC NAME

FOLDER

MP3

5DUAL PLAYBACK

JPEG

folder name

MP3

JPEG

file name

ENTER

PLAY

folder name

This function lets you play back MP3 and JPEG ﬁles simultaneously. Avail-

able only when “Dual Playback” is “ON“. See page 43 on how to set the Dual

Playback ON or OFF.

• Press [s] when you want to go back to the previous

hierarchy (except for the top hierarchy).

• If [TITLE] is pressed when a FILE LIST is displayed, the

1st item in the top hierarchy will be highlighted.

• Press [DISC MENU] or [BACK/RETURN] to go back to

Press [PLAY B], then press [DISC MENU].

FILE LIST

DISC NAME

FOLDER

MP3

JPEG

folder name

playback display.

file name

ENTER

PLAY

folder name

Press [STOP C] once to stop playback temporarily.

When playing back an MP3 file, use [K / L] to select a

desired JPEG file from the FILE LIST, then press [ENTER]

(or [PLAY B]).

• Refer to “RESUME“ on page 30.

NOTE:

• Some selections may take a while to be recognized.

• Folders are known as Groups; files are known as Tracks.

• Folders, MP3 files and JPEG files are displayed respectively as

• When playing back a JPEG file, select an MP3 file.

and

NOTE:

• A maximum of 255 folders or 999 files may be recognized in

one disc.

• Up to 8 hierarchies can be recognized in one folder. Files in the

9th or deeper hierarchies cannot be played back.

• This unit can play back images and sounds from data recorded

in MP3 and JPEG formats on CD-RW/-R discs.

• A file with an extension of “.mp3 (MP3)” is called an “MP3 file”.

• A file with an extension of “.jpg (JPG)” or “.jpeg (JPEG)” is called

a “JPEG file”.

• The unit can run an image file conforming to the Exif specifi-

cation. Exif is a file format, Exchangeable Image File format

established by Japanese Electronic Industry Development

Association (JEIDA).

• To cancel Dual Playback, press [DISC MENU] again at step 1.

• If you press [PLAY B] directly after you inserted a disc which con-

tains both MP3 tracks and JPEG files and if the “DUAL PLAYBACK”

setting is “ON”, Dual Playback will start automatically.

• If you press [FWD D] or [REV E] during Dual Playback, a

JPEG file will be paused.

• Zooming or rotating a JPEG file during Dual Playback may

cause an intermittent sound.

• Depending on the data size of each file, Dual Playback may not

function properly. (Refer to “Applicable JPEG file” on page 32.)

• Files whose extension is other than “.mp3 (MP3)”, “.jpg (JPG)”

and “.jpeg (JPEG)” will not be listed in the MP3 or JPEG menu.

• If the file is not recorded in MP3 or JPEG format, noise may be

produced even if the file extension is either “.mp3 (MP3)”, “.jpg

(JPG)” or “.jpeg (JPEG)”.

• The name of group and track can be displayed in up to 25 char-

acters. Unrecognizable characters will be replaced with asterisks.

• Unplayable groups or tracks may be displayed depending on

the recording conditions.

• Progressive JPEGs (JPEG files saved in the progressive format)

will not play on this unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

5FOLDER PLAYBACK

5ADJUSTMENT OF PICTURE SIZE

MP3

JPEG

This function lets you play all the ﬁles and tracks contained in one selected

folder automatically. Available only when “Dual Playback” is “ON“.

If the folder contains both MP3 and JPEG ﬁles, the Dual Playback will

begin automatically within that folder. See page 43 on how to set the Dual

Playback ON or OFF.

When the overall picture cannot be displayed and the edge of the picture is

cut oﬀ, you can adjust the size of the JPEG playback image on screen.

Press [STOP C], then press [MODE].

Press [PLAY B], then press [MODE] repeatedly until

“

” appears.

FOLDER LIST

NORMAL

DISC NAME

FOLDER

folder name

ALL

ENTER

PLAY

folder name

Use [ENTER] or [ s / B] to select a desired setting.

Use [K / L] to select a desired folder from the FOLDER

LIST, then press [ENTER] (or [PLAY B]).

SMALL

NORMAL

SMALL

: To display the image at 100% of the

picture size.

: To display the image at 95% of the pic-

ture size.

NOTE:

• To cancel Folder Playback, press [MODE] again at step 1.

• If you press [FWD D] or [REV E] during Folder Playback, a

JPEG file will be paused.

• Zooming or rotating a JPEG file during Folder Playback may

cause an intermittent sound.

• Depending on the data size of each file, Folder Playback may not

function properly. (Refer to “Applicable JPEG file” on page 32.)

To exit the Picture Adjustment mode, press

[BACK/RETURN].

NOTE:

• The setting screen will not be displayed while in the stop mode

or from the FILE LIST.

• This feature may have no effect on some files (e.g. Files with a

small picture size).

5TRANSITION MODE

JPEG

• The default setting is “NORMAL”.

You can switch to the Transition Mode for JPEG ﬁles during playback.

Press [PLAY B], then press [MODE] repeatedly until

“

” appears.

CUT IN/OUT

Use [ENTER] or [s / B] to select a desired setting.

FADE IN/OUT

CUT IN/OUT : The entire image appears in one time.

FADE IN/OUT : The image appears gradually and then

disappears.

To exit the Transition mode, press [BACK/RETURN].

NOTE:

• The Transition mode cannot be switched when it is stopped, or

from the FILE LIST screen.

• The default setting is “CUT IN/OUT”.

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING DVD

5SEARCH FUNCTIONS

CHAPTER / TITLE Search

DVD

TRACK Search

MP3

JPEG

Using [SEARCH MODE]

Press [SEARCH MODE] once to display the Track

Search display.

Press [SEARCH MODE] once to display the Chapter

Search display.

/29

/12

• Press [SEARCH MODE] twice for the Title search (

Press [the Number buttons] to select your desired

track within 30 seconds.

Press [the Number buttons] to select a desired chap-

ter or title within 30 seconds.

/29

/12

Playback will start automatically from the track you

searched.

Playback will start automatically from the chapter or

title you searched.

NOTE:

Using [SKIP H , G]

The total number of tracks in your disc;

• With less than 10 tracks, press the track number directly.

During playback, press [SKIP H, G] repeatedly

until a desired chapter or title will be selected.

• With 10 or more but less than 100 tracks,

To play a single digit track,

Current Chapter

press [0] first, then the track number.

e.g.) for track 3, press [0], [3].

(CH)

CH 1 CH 2 CH 3 CH 4

To play a double-digit track, press the track number.

SKIP

• With 100 or more tracks,

To play a single or double digit track, press [0] first,

then the track number directly.

e.g.) for track 3, press [0], [0], [3], for track 26, press

[0], [2], [6]).

Current Title

(TT)

TT 1 TT 2 TT 3 TT 4

To play a triple-digit track, press the track number

directly.

SKIP

(If the disc has only 1 chapter.)

• Track Search is not available for Programmed or Random Playback.

Playback will start automatically from the chapter or

title you searched.

• The Track Search can only be performed during playback or

when the unit has kept the resume information. It cannot be

performed in the stop mode.

NOTE:

• Depending on the disc being played, this function can also be

performed by directly entering the desired chapter number with

the [the Number buttons]. Refer to the manual accompanying

the disc.

Using [SKIP H , G]

During playback, press [SKIP H, G] repeatedly

until a desired track will be selected.

• The Chapter or Title Search can only be performed during play-

back or when the unit has kept the resume information. It can-

not be performed in the stop mode.

Current Track

(TR)

TR 1 TR 2 TR 3 TR 4

SKIP

Playback will start automatically from the track you

searched.

NOTE:

• [SKIP H / G] are not available when playback is stopped.

Download from Www.Somanuals.com. All Manuals Search And Download.

5REPEAT PLAYBACK

TIME Search

DVD

MP3

JPEG

Repeat function is available only during playback.

DVD

During playback, press [SEARCH MODE] repeatedly

During playback, press [REPEAT] repeatedly until the

desired repeat setting.

until the “

“ appears.

TOTAL

1:29:00

Press [the Number buttons] to select your desired

time within 30 seconds.

Each time you press [REPEAT], repeat function changes

as example below.

DVD

TOTAL

1:29:00

OFF

(repeat off)

CHAPTER (current chapter repeat)

Playback will start automatically from the time you

searched.

TITLE (current title repeat)

NOTE:

• When there is no need to enter a number, “0” appears automati-

cally. For example, “0: 0_ : _ _” appears in the Time Search dis-

play if the total time of the title or track is less than 10 minutes.

OFF

(repeat off)

• Press [CLEAR] to erase the incorrect input at step 2.

TRACK (current track repeat)

• The Time Search can only be performed during playback or

when the unit has kept the resume information. It cannot be

performed in the stop mode.

ALL

(entire disc repeat)

MP3

JPEG

OFF

(repeat off)

TRACK (current track repeat)

GROUP (current group repeat)

ALL

(entire disc repeat)

To exit the Repeat function display,

press [BACK/RETURN].

NOTE:

• Repeat setting (except “ALL“) will be cleared when moving to

another title, chapter, track or group.

• Repeat playback may not function with some discs or during

Repeat A-B Playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING DVD

5REPEAT AB PLAYBACK

5PROGRAMMED PLAYBACK

DVD

MP3

JPEG

This feature allows you to assign a speciﬁc point on a disc to be called back

later.

You may determine the order in which tracks will play.

During playback, press [A-B] at your desired starting

point (A).

In stop mode, press [MODE] once.

PROGRAM

CD-DA

TOTAL 0:00:00

A-

3:31

4:28

4:19

3:58

4:12

4:02

3:55

ENTER

PLAY

3:31

CLEAR

Press [A-B] at your desired ending point (B).

Use [K / L] to select a desired track from the FILE LIST,

then press [ENTER] to store.

A-B

PROGRAM

CD-DA

TOTAL 0:08:22

3:58

15 3:18

16 4:24

ALL CLEAR

• Point B should be in the same title or track as point A.

ENTER

PLAY

16 4:24

CLEAR

To exit the sequence, press [A-B] so that “OFF“ appears.

• Up to 99 tracks can be ordered.

• If 8 or more tracks were in a program, use

[SKIP H / G] to see all the tracks.

NOTE:

While an MP3 or a JPEG folder is open:

• To cancel Point A, press [CLEAR] at step 1.

• This function does not work in the other repeat modes.

– Press [ B] when you want to go to the next hierarchy.

– Press [s] when you want to go back to the previous

hierarchy (except for the top hierarchy).

– Press [TITLE] when you want to go back to the item in

the top hierarchy.

5RANDOM PLAYBACK

MP3

JPEG

This function shuﬄes the playing order of tracks instead of playback in the

sequence.

Press [PLAY B] to start Programmed Playback.

In stop mode, press [MODE] twice.

RANDOM

NOTE:

CD-DA

TOTAL 0:45:55

• Press [ENTER] at step 2 to erase the most recently entered

RANDOM PROGRAM

--no indication--

track.

• To erase all programmed tracks at once, select “ALL CLEAR’’

and press [ENTER] at step 2.

PLAY

• While a program is being played back, [STOP C] works as fol-

lows:

- Press [STOP C] and [PLAY B] next, so that the programmed

playback restarts. (CD playback restarts from the current point.

MP3 or JPEG playback restarts from the beginning of the cur-

rent track.)

Press [PLAY B] to start Random Playback.

- Press [STOP C] and [PLAY B] next, so that playback restarts

from the first track in the original order. However, your pro-

grammed playback can be restarted when you follow the

above steps. (Your programs are still stored until either the

disc is ejected or power is turned off.)

NOTE:

• To repeat the current track in the random selections, press

[REPEAT] repeatedly until “

back.

• To repeat the entire random selections, press [REPEAT] repeat-

edly until “ ALL” appears during playback.

• Random Playback of MP3 or JPEG is not available while “Dual

Playback” is “ON”.

• The Random Playback will be kept until you press [STOP C].

TRACK” appears during play-

On some discs, [STOP C] will not work while the Resume

message appears. Please wait until the message disappears.

• To repeat the current track in the program, press [REPEAT]

repeatedly until “

TRACK’’ appears during playback.

• To repeat the entire program, press [REPEAT] repeatedly until

“

ALL’’ appears during playback.

• Programmed Playback of MP3 or JPEG is not available while

“Dual Playback” is “ON”.

• The Program Playback will be kept until you press [STOP C]

twice and saved the programmed order until the disc is ejected.

• Press [CLEAR] to erase the incorrect track number at step 2.

Download from Www.Somanuals.com. All Manuals Search And Download.

5ONSCREEN DISPLAY

You can check the information about the current disc by pressing [INFO] on the

remote control.

Current playback status

DVD

4/12 0:03:21 - 0:02:15

Remaining time of the current

track

Elapsed time of the current track

Angle icon, appears only when

available on the DVD.

Current playback status

11/16 0:00:00 - 0:03:30

TR (Track):

Current track number /

Total tracks

Remaining time of the current

chapter

Elapsed time of the current

chapter

CH (Chapter):

Current chapter number /

Total chapters

ALL:

Current track number /

Total tracks

4/12 0:13:45 - 0:45:40

Current repeat setting

appears only when the

repeat setting is active.

T : Track repeat

A : All tracks repeat

B : A-B repeat

1/3 0:00:00 - 1:23:45

Remaining time of the entire disc

Remaining time of the current title

Elapsed time of the current title

Elapsed time of the entire disc

TT (Title):

Current title number / Total titles

NOTE:

• When you are playing a disc in PROGRAM or RANDOM mode,

“

PROGRAM” (or “

RANDOM”) will be displayed instead

Layer numbers, appears only

when playing a two-layered disc.

L0 : Layer 0 is playing

MP3

JPEG

L1 : Layer 1 is playing

Current repeat setting appears

only when the repeat setting is

active.

Current playback status

TRACK 01

The name of the file currently in

playback will be displayed.

C :Chapter repeat

T :Title repeat

B :A-B repeat

TR (Track):

Current track number /

Total tracks

BIT RATE: The amount of audio and

video data currently being read.

1/36 0:01:15

Current Repeat setting, if active

T : Track repeat

G : Group (folder) repeat

A : Disc repeat

Elapsed playing time of the

current track

NOTE:

•

Some DVD discs will not allow you to set chapter playback cor-

rectly.

PROGRAM

RANDOM

*Only when you are playing a disc in PROGRAM

or RANDOM mode.)

NOTE:

• When the “Dual Playback” is “ON”, MP3 and JPEG file name will

be displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

PERATING DVD

• Each time you press [AUDIO], the audio language

changes as example below.

5SPECIAL SETTINGS

Subtitle Language

ENG

(English audio)

DVD

SPA

(Spanish audio)

This unit allows you to select a subtitle language (if available) during DVD

playback.

FRE

(French audio)

During playback, press [SUBTITLE] repeatedly until the

desired language appears.

NOTE:

• Some discs will only allow you to change the audio setting

from the disc menu. Refer to the manual accompanying the

discs for details.

1.ENG/6

• If your language is not shown after pressing [AUDIO] several

times, the disc may not have that language. However, some

discs allow you to change multiple audio languages setting

in the disc menu. (Operation varies depending on the disc, so

refer to the manual along with the disc.)

• When “NOT AVAILABLE“ appears on the TV screen, it means

audio language is not available.

Subtitles can be varied on

the displayed number.

Current subtitles language.

• Each time you press [SUBTITLE], the subtitle lan-

guage changes as example below.

OFF

(no subtitles)

ENG

(English subtitles)

Camera Angles

DVD

FRE

(French subtitles)

Some DVD discs may contain scenes which have been shot

simultaneously from various angles. You can change the

camera angle if “ ” appears on the screen. If the “ANGLE ICON”

setting is “OFF” in the OTHERS menu, “ ” will not appear.

(Refer to page 43.)

To cancel the subtitle

During playback, press [SUBTITLE] to display the sub-

title display.

During playback, press [ANGLE] repeatedly until the

desired camera angle appears.

1.ENG/6

1 / 8

Press [ B] button to set “OFF“.

OFF

Black Level Setting

DVD

NOTE:

• If your language is not shown after pressing [SUBTITLE] sever-

al times, the disc may not have that language. However, some

discs allow you to change subtitle languages setting in the disc

menu. (Operation varies depending on the disc, so refer to the

manual along with the disc.)

Adjust the Black Level Setting to make the dark areas of the TV picture

brighter.

During playback, press [MODE] repeatedly until the

“

“ appears.

• When “NOT AVAILABLE” appears on the TV screen, it means no

subtitle is recorded on the scene.

OFF

• If you choose a language that has 3-letter-language code, the

code will be displayed every time you change the subtitle lan-

guage setting. If you choose any other languages, “---” will be

displayed instead. (Refer to page 44.)

Press [ENTER] to adjust the black level.

Audio Language

DVD

ON :Makes the dark areas brighter.

OFF :Shows the original picture as recorded.

This unit allows you to select an audio language (if multiple languages are

available) during DVD playback.

To exit the Black Level setting, press [BACK/RETURN].

Press [AUDIO] repeatedly until the desired language

appears.

1.ENG Dolby D 3/2.1ch 48k/3

NOTE:

• The setting will be kept even if the unit is turned off.

Audio can be varied on

the displayed number.

Current audio language.

Download from Www.Somanuals.com. All Manuals Search And Download.

Stereo Sound Mode

Marker Setup

DVD

This unit allows you to select a sound mode during CD playback.

This feature allows you to assign a speciﬁc point on a disc to be called back

later.

To set a marker

Press [AUDIO] repeatedly until the desired sound

mode appears.

During playback, press [SEARCH MODE] repeatedly

STEREO

until the “ “ appears.

• Each time you press [AUDIO], the audio language

changes as example below.

Use [s / B] to select a desired marker within 30 sec-

onds.

STEREO(Right and left channels are active.)

L-ch

R-ch

(Left channel is active.)

(Right channel is active.)

Press [ENTER] to set the marker.

NOTE:

• Virtual Surround cannot be changed when the sound mode is

set to either L-ch or R-ch.

Virtual Surround

To exit the Marker setup display,

press [BACK/RETURN].

DVD

MP3

You can enjoy virtual surround sound on your existing 2 channel stereo

system.

To return to the marker later

During playback, press [MODE] repeatedly until the

In stop mode, press [SEARCH MODE] repeatedly until

“

“ appears.

the “ “ appears.

OFF

Press [ENTER] to select the sound level.

Use [s / B] to select a desired marker within 30 sec-

onds.

: Natural effect.

: Emphasized effect.

OFF : No effects (original sound).

Press [ENTER] at the desired marker to restart playback

from the specific point which you set.

To exit the Virtual Surround setting,

press [BACK/RETURN].

NOTE:

• The Marker display will disappear in about 30 seconds when

there is no input.

• You can mark up to 10 points.

• To clear a marker, select the marker to be cleared at step 2 in

the section “To set a marker” or “To return to the marker later”,

and then press [CLEAR].

NOTE:

• The setting will be kept even if the unit is turned off.

• On Audio CDs, Virtual Surround will not be effective if the

sound mode is set to something other than “STEREO”.

Refer to “Stereo Sound Mode”.

• Turn down the level or select “OFF” if the sound is distorted.

• Ejecting the disc or turning off the power will erase all markers.

• Selecting “ ” at step 2 in the section “To set a marker” or “To

return to the marker later” will also erase all markers.

Download from Www.Somanuals.com. All Manuals Search And Download.

ETTING DVD

Settings are only effective when the unit is in DVD mode and any discs should not be played back.

5DVD LANGUAGE SETTING

You can change the output language of the DVD player.

Use [

] to select the desired item, then press

[ENTER].

Press [SETUP] to display the setup screen.

[AUDIO] *1, *2

Sets the desired audio language.

(Default: ORIGINAL)

EXIT

PICTURE

CHANNEL

DETAIL

LANGUAGE

AUDIO

LANGUAGE

DVD

ORIGINAL

ENGLISH

FRENCH

SPANISH

GERMAN

ITALIAN

ENTER

Use [

] to select “DVD”, then press [ENTER].

SWEDISH

Setup

EXIT

PICTURE

Press “ENTER” key to move to DVD Setup.

CHANNEL

DETAIL

[SUBTITLE] *1, *2

Sets the desired subtitle language.

(Default: OFF)

LANGUAGE

DVD

LANGUAGE

SUBTITLE

OFF

ENGLISH

FRENCH

SPANISH

GERMAN

ITALIAN

Use [s / B] to select “ “, then press [ENTER].

ENTER

SWEDISH

LANGUAGE

AUDIO

ORIGINAL

OFF

SUBTITLE

DISC MENU

[DISC MENU] *1

(Default: ENGLISH)

ENGLISH

ENTER

Sets the desired language in DVD menu.

LANGUAGE

DISC MENU

ENGLISH

FRENCH

SPANISH

GERMAN

ITALIAN

Use [

] to select the desired item, then press

[ENTER].

ENTER

SWEDISH

DUTCH

LANGUAGE

NOTE:

AUDIO

ORIGINAL

OFF

SUBTITLE

DISC MENU

ENGLISH

• Language options are not available with some discs.

ENTER

• If “OTHER” is selected in the AUDIO, SUBTITLE or DISC MENU

screen, press four-digit number to enter the code for the desired

language. (Refer to “LANGUAGE CODE LIST” on page 44.)

• Only the languages supported by the disc can be selected.

• Language setting for Audio and Subtitle are not available

with some discs. Then press [AUDIO] and [SUBTITLE].

Details are on page 38.

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

5DVD AUDIO SETTING

Choose the appropriate audio settings for your equipment. It only aﬀects

during the playback of DVD discs.

Use [

] to select the desired item, then press

[ENTER].

[DRC]

(Default: ON)

Press [SETUP] to display the setup screen.

Sets the Dynamic Range Control.

This function is available only on the discs which are

recorded in the Dolby Digital format.

EXIT

PICTURE

CHANNEL

DETAIL

LANGUAGE

DVD

AUDIO

DRC

DOWN SAMPLING ON

DOLBY DIGITAL BITSTREAM

Use [

] to select “DVD”, then press [ENTER].

ENTER

Setup

EXIT

PICTURE

Press “ENTER” key to move to DVD Setup.

CHANNEL

DETAIL

ON : Compress the range between soft and loud

sounds.

OFF : No effects (original sound).

LANGUAGE

DVD

[DOWN SAMPLING]

(Default: ON)

This function is available only on digital outputting of a

disc recorded in 96kHz.

Use [s / B] to select “ “, then press [ENTER].

AUDIO

DRC

DOWN SAMPLING ON

DOLBY DIGITAL BITSTREAM

DRC

DOWN SAMPLING ON

DOLBY DIGITAL BITSTREAM

ENTER

ON : When outputting in 48kHz.

OFF : When outputting the original sound.

NOTE:

Use [

] to select the desired item, then press

• When playing back a 96 kHz disc with the copyright protec-

tion or when Virtual Surround is set to 1 or 2, the sound will

be down sampled at 48 kHz and output as digital audio even

if the “DOWN SAMPLING” is set to “OFF”.

[ENTER].

AUDIO

DRC

DOWN SAMPLING ON

DOLBY DIGITAL BITSTREAM

[DOLBY DIGITAL]

(Default: BITSTREAM)

Sets “BITSTREAM“ when this unit is connected to a

Dolby Digital decoder.

ENTER

AUDIO

DRC

DOWN SAMPLING ON

DOLBY DIGITAL BITSTREAM

ENTER

BITSTREAM : Outputs Dolby Digital signals.

PCM

: Converts the Dolby Digital into PCM.

(2 channel)

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

ETTING DVD

5PARENTAL SETTING

Parental setting prevents your children from viewing inappropriate materi-

als. (password protected.) Playback will stop if the ratings exceed the levels

you set.

Use [

] to select the desired item, then press

[ENTER].

PARENTAL

Press [SETUP] to display the setup screen.

PARENTAL LEVEL

ALL

EXIT

[ ADULT ]

[ NC-17 ]

[ R ]

PICTURE

ENTER

[ PGR ]

[ PG13 ]

[ PG ]

CHANNEL

DETAIL

LANGUAGE

DVD

CONTROL LEVELS

ALL

LEVEL 8

: All parental locks are cancelled.

: All ratings (adult/general/children) can

be played back.

Use [

] to select “DVD”, then press [ENTER].

Setup

EXIT

LEVEL 7 to 2 : Only DVDs intended for general use and

PICTURE

Press “ENTER” key to move to DVD Setup.

children can be played back.

: Only DVDs intended for children can

be played back.

CHANNEL

DETAIL

LEVEL 1

LANGUAGE

DVD

To exit the setup, press [SETUP].

Use [s / B] to select “ “, then press [ENTER].

PARENTAL

To change the password

PARENTAL LEVEL ALL

Follow steps 1 to 4. Use [

] to select “PASSWORD

ENTER

CHANGE“, then press [ENTER].

Use [the Number buttons] to enter the 4-digit num-

bers for your password, then press [ENTER].

PARENTAL

PARENTAL LEVEL ALL

PASSWORD CHANGE

ENTER

PARENTAL

PASSWORD

Please enter

4-digit password.

Use [the Number buttons] to enter the new 4-digit

password, then press [ENTER].

ENTER

Don’t forget the password.

Press ‘ENTER’ to activate password.

• If you have set password already, use [the Number

buttons] to enter the current 4-digit password.

PARENTAL

PASSWORD

Please enter

4-digit password.

Use [

] to select the “PARENTAL LEVEL“, then press

[ENTER].

ENTER

Don’t forget the password.

Press ‘ENTER’ to activate password.

PARENTAL

NOTE:

PARENTAL LEVEL ALL

PASSWORD CHANGE

• DVD-Video discs may not respond to parental lock settings.

Make sure this function works with your DVD-Video discs.

ENTER

• Record the password in case you forget it.

• If you forget the password, press [4], [7], [3], [7] at step 6,

then enter your new password. Password will be cleared and

parental levels will be set to “ALL”.

To exit the setup, press [SETUP].

Download from Www.Somanuals.com. All Manuals Search And Download.

[STILL MODE]

See note bellow.

(Default: AUTO)

5OTHERS

You can change the other functions.

OTHERS

Press [SETUP] to display the setup screen.

ANGLE ICON

STILL MODE

EXIT

AUTO

AUTO POWER OFF ON

PICTURE

DUAL PLAYBACK

SLIDE SHOW

OFF

5sec

ENTER

CHANNEL

DETAIL

LANGUAGE

DVD

NOTE:

STILL MODE:

• Select “AUTO” usually.

Use [

] to select “DVD”, then press [ENTER].

• If you select “FIELD”, the picture in the still mode will be sta-

Setup

EXIT

bilized.

PICTURE

Press “ENTER” key to move to DVD Setup.

• If you select “FRAME”, the picture in the still mode will be

highly defined.

CHANNEL

DETAIL

LANGUAGE

DVD

[AUTO POWER OFF]

(Default: ON)

Set to “ON” to turn this unit off automatically after 20

minutes of no use.

Use [s / B] to select “ “, then press [ENTER].

OTHERS

ANGLE ICON

STILL MODE

AUTO

AUTO POWER OFF ON

OTHERS

DUAL PLAYBACK

SLIDE SHOW

OFF

5sec

ENTER

ANGLE ICON

STILL MODE

AUTO

AUTO POWER OFF ON

DUAL PLAYBACK

SLIDE SHOW

OFF

5sec

ENTER

[DUAL PLAYBACK]

(Default: OFF)

Set to “ON” to play back MP3 and JPEG files simultane-

ously.

Use [

] to select the desired item, then press

[ENTER].

OTHERS

ANGLE ICON

STILL MODE

AUTO

OTHERS

AUTO POWER OFF ON

DUAL PLAYBACK

SLIDE SHOW

OFF

5sec

ENTER

ANGLE ICON

STILL MODE

AUTO

AUTO POWER OFF ON

DUAL PLAYBACK

SLIDE SHOW

OFF

5sec

ENTER

[SLIDE SHOW]

Set to the length of displayed JPEG picture.

5sec : The picture changes every 5 seconds.

(Default: 5sec)

Use [

] to select the desired item, then press

10sec : The picture changes every 10 seconds.

[ENTER].

[ANGLE ICON]

(Default: ON)

OTHERS

Set to “ON” to show the angle icon when multiple cam-

era angles are available during DVD playback.

ANGLE ICON

STILL MODE

AUTO

AUTO POWER OFF ON

DUAL PLAYBACK

SLIDE SHOW

OFF

5sec

ENTER

OTHERS

ANGLE ICON

STILL MODE

AUTO

AUTO POWER OFF ON

To exit the setup, press [SETUP].

DUAL PLAYBACK

SLIDE SHOW

OFF

5sec

ENTER

Download from Www.Somanuals.com. All Manuals Search And Download.

ETTING DVD

RESET TO THE DEFAULT SETTING

Language

LANGUAGE CODE LIST

You can reset all the settings except for the PARENTAL setting and

Code

Language

Marathi

Code

5964

5961

5960

6047

6051

6061

on-screen menu language.

A-B

Abkhazian

Afar

4748

4747

4752

6563

4759

4764

5471

4765

4771

4772

4847

5167

4860

5072

4854

4855

4864

4853

5971

4851

Moldavian

Mongolian

Nauru

Afrikaans

Albanian

Amharic

Arabic

Press [SETUP] to display the setup screen.

Nepali

EXIT

Norwegian [NOR]

O-R

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

PICTURE

CHANNEL

DETAIL

Occitan

Oriya

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

LANGUAGE

DVD

Oromo(Afan)

Panjabi

Basque

Bengali;Bangla

Bhutani

Pashto;Pushto

Persian

Bihari

Use [

] to select “DVD”, then press [ENTER].

Bislama

Polish [POL]

Portuguese [POR]

Quechua

Rhaeto-Romance

Romanian [RUM]

Russian [RUS]

Breton

Setup

EXIT

Bulgarian

Burmese

Byelorussian

PICTURE

Press “ENTER” key to move to DVD Setup.

CHANNEL

DETAIL

C-E

Cambodian

Catalan

5759

4947

7254

4961

5464

4965

5047

6058

5160

5161

5166

LANGUAGE

DVD

Chinese [CHI]

Corsican

Samoan

Sangho

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

Croatian

Czech [CZE]

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

Sanskrit

Scots Gaelic

Serbian

Serbo-Croatian

Sesotho

Setswana

Shona

Sindhi

Singhalese

Siswat

Slovak

Slovenian

Somali

Spanish [SPA]

Sundanese

Swahili

Use [s / B] to select “ “, then press [ENTER].

F-H

Faroese

5261

5256

5255

5264

5271

5358

5747

5051

5158

5758

5360

5367

5447

5569

5455

5467

INITIALIZE

Fiji

Finnish [FIN]

French [FRE]

Frisian

Initialize?

YES

Galician

Georgian

ENTER

German [GER]

Greek [GRE]

Greenlandic

Guarani

Gujarati

Hausa

Use [

] to select “YES“, then press [ENTER].

Hebrew

Swedish [SWE]

Hindi

Hungarian [HUN]

I-K

Tagalog

Tajik

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

INITIALIZE

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

5565

5560

5547

5551

5557

5347

5566

5647

5669

5760

5765

5757

6469

5771

6460

5761

5767

Tamil

Initialize?

Tatar

YES

Telugu

ENTER

Thai

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

Kazakh

Tibetan

Tigrinya

Tonga

NOTE:

Tsonga

• When you want to cancel the initialization, select “NO”

Turkish [TUR]

Turkmen

Twi

at step 4, then press [SETUP].

Kinyarwanda

Kirghiz

Kirundi

U-Z

Korean [KOR]

Kurdish

Ukrainian

Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

To exit the setup, press [SETUP].

L-N

Laothian

Latin

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

Vietnamese

Volapuk

Welsh

Latvian;Lettish

Lingala

Lithuanian

Macedonian

Malagasy

Malay

Wolof

Xhosa

Yiddish

Malayalam

Maltese

Yoruba

Maori

Zulu

NOTE:

• If you choose a language that has a 3-letter language code,

the code will be displayed every time you change the AUDIO

or SUBTITLE language setting above. If you choose any other

language, ‘---’ will be displayed instead. (3-letter language

code is written in bracket.)

Download from Www.Somanuals.com. All Manuals Search And Download.

ROUBLESHOOTING

5TROUBLESHOOTING GUIDE

If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the following chart

once before calling for service.

Symptom

Remedy

No power

• Be sure the power cord is plugged in.

• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to

reset itself.

No picture or sound

• Check if the power is on.

• Check the outlet connection.

• Check the antenna or cable connection to the main unit.

• When the outside antenna is used, check the wire condition and connection.

• View other TV channels. The problem might be limited to the broadcasting station.

• Turn off the power and wait for about 1 minute, then turn it on again.

No color

• Check the antenna or cable connection to the main unit.

• When the outside antenna is used, check the wire condition and connection.

• View other TV channels. The problem might be limited to the broadcasting station.

• Adjust the Color in the setup screen.

Sound OK, picture poor

• Check the antenna or cable connection to the main unit.

• When the outside antenna is used, check the wire condition and connection.

• Electrical interference from nearby appliances may affect picture quality.

• Adjust Contrast and Brightness in the setup screen.

• View other TV channels. The problem might be limited to the broadcasting station.

Picture distorted

Weak picture

• When the outside antenna is used, check the wire condition and connection.

• View other TV channels. The problem might be limited to the broadcasting station.

• Check the antenna or cable connection to the main unit.

• When the outside antenna is used, check the wire condition and connection.

• Adjust Contrast and Brightness in the setup screen.

• View other TV channels. The problem might be limited to the broadcasting station.

Lines or streaks in picture

• When the outside antenna is used, check the wire condition and connection.

• Electrical interference from nearby appliances may affect picture quality.

• View other TV channels. The problem might be limited to the broadcasting station.

Picture blurred

• When the outside antenna is used, check the wire condition and connection.

• View other TV channels. The problem might be limited to the broadcasting station.

Ghosts in picture

• Check the antenna or cable connection to the main unit.

• When the outside antenna is used, check the wire condition and connection.

• Electrical interference from nearby appliances may affect picture quality.

• View other TV channels. The problem might be limited to the broadcasting station.

Bars on screen

• When the outside antenna is used, check the wire condition and connection.

• Electrical interference from nearby appliances may affect picture quality.

Picture rolls vertically

• When the outside antenna is used, check the wire condition and connection.

• Electrical interference from nearby appliances may affect picture quality.

• View other TV channels. The problem might be limited to the broadcasting station.

Different color marks on

screen

• Move your TV away from nearby electric appliances. Turn off the power and wait

30 minutes before turning it back on.

• View other TV channels. The problem might be limited to the broadcasting station.

Poor reception on some chan- • Check the antenna or cable connection to the main unit.

nels

• When the outside antenna is used, check the wire condition and connection.

• Electrical interference from nearby appliances may affect picture quality.

• View other TV channels. The problem might be limited to the broadcasting station.

Picture OK, sound poor

• Electrical interference from nearby appliances may affect picture quality.

• View other TV channels. The problem might be limited to the broadcasting station.

No reception of digital signals • Make sure Autoscan has been completed (Refer to “AUTOSCAN”on page 14).

Autoscan must be completed when you set up your TV for the first time or move it

to a location where previously unavailable channels are broadcast.

• The selected channel may not be broadcasting.

• When Autoscan is interrupted and not completed, some channels will not be

received. Make sure to complete Autoscan in the setup screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

ROUBLESHOOTING

Symptom

Remedy

The entered channel number

changes automatically

•

Many digital channels have alternate channel numbers. TV changes the numbers automati-

cally to the ones signifying the broadcasting stations. These are the numbers used for analog

broadcasts.

Remote control does not work • Check the antenna or cable connection to the main unit.

• Check the batteries of the remote control.

• Check if there is an obstacle between the sensor and the remote control.

• Test the signal output. If OK, then possible remote sensor trouble.

(Refer to “IR SIGNAL CHECK”on page 47.)

• Aim the remote control directly at the sensor on the front of the unit.

• Reduce the distance to the unit.

• Re-insert the batteries with their polarities (+/– signs) as indicated.

Problems with Closed Caption Feature

Misspelled captions are dis-

played.

• Closed captioning production companies may broadcast programs without cor-

recting the misspelling in a live broadcast.

Captions are not entirely dis-

•

Captions that are delayed a few seconds behind the actual dialogue are common for live

played, or captions are delayed broadcasts. Most captioning production companies can display a dialogue to a maxi-

behind the dialogue.

mum of 220 words per minute. If a dialogue exceeds that rate, selective editing is used to

insure that the captions remain up-to-date with the current TV screen dialogue.

Captions are displayed as a

white box.

No caption is displayed in the

Closed Caption-supported

program.

• Interference from buildings or weather conditions may cause captioning to be

incomplete.

• Broadcasting station may shorten the program to insert advertisement. The closed

caption decoder cannot read the information of the shortened program.

No caption is displayed when

• The videotape may be illegally copied, or the caption signal might not have been

playing the videotape contain- read during copying.

ing captions.

Black box is displayed in the

screen.

• “Text”mode is selected for caption. Select “CC1”, “CC2”, “CC3”, “CC4”or “Off”.

Completely distorted picture

or black/white picture with

DVD

• Make sure the disc is compatible with the unit.

Picture freezes momentarily

during playback.

• Check the disc for ﬁnger prints/scratches and clean with a soft cloth wiping from

center to edge.

Disc cannot be played.

• Clean the disc.

• Ensure the disc is correctly inserted.

• Check if the disc is defective by trying another disc.

• Cancel the parental lock or change the control level.

• Insert a correct disc that plays on this unit.

• Handle a disc with special care so that it does not have ﬁngerprints, scratches, or

dusts on its surface.

Buttons do not work or the

unit stops responding.

• To completely reset the unit, unplug the power cord from the power outlet for

5-10 seconds.

The unit does not respond to

some operating commands

during playback.

• Operations may not be permitted by the disc. Refer to the instructions of the disc.

Angle does not switch.

• The angle cannot be switched for DVDs which do not contain multiple angles. In

some cases multiple angles are only recorded for speciﬁc scenes.

Playback does not start

when the title is selected.

• Check the “PARENTAL”setting.

The password for rating level

has been forgotten.

• Enter the default password “4737”, then your forgotten password will be cleared.

NOTE:

• The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a fixed point of

blue, green or red. This is not to be considered a defect in the LCD screen.

• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for more

details on correct operations.

• Playback from a desired track and random playback are not available during program playback.

• Some functions are prohibited on some discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

NFORMATION

5GLOSSARY

ATSC

HDMI

Password

A stored 4-digit number that allows access

to parental control features.

(High-Definition Multimedia Interface)

Acronym that stands for Advanced Television

Systems Committee and the name of the

digital broadcasting standards.

Interface that supports all uncompressed,

digital audio/video formats including set-top

box, DVD player or digital television, over a

single cable.

High Definition TV (HDTV)

Ultimate digital format that produces high

resolution and high picture quality.

SAP

Aspect ratio

(Secondary Audio Program)

The width of a TV screen relative to its

height. Conventional TVs are 4:3 (in

other words, the screen is almost square);

widescreen models are 16:9 (the screen is

almost twice as wide as its height).

Second-audio channel delivered sepa-

rately from main-audio channel. This audio

channel is used as an alternate in bilingual

broadcasting.

Standard Definition TV (SDTV)

Standard digital format that is similar to the

NTSC picture quality.

LPCM

Component video

(Linear Pulse Code Modulation)

This is a video signal format that conveys

each of three principal colors of light (red,

blue and green) through different signal

lines. This allows the viewers to experience

picture colors as original as it is. There are

several signal formats, including Y / Pb / Pr

and Y / Cb / Cr.

LPCM is a format that can have up to 8

channels of audio. It is mainly used in

music production. The format samples and

captures analog signals and transforms

them into digital signals without compress-

ing the sound data.

S-Video

Offers higher quality images by deliver-

ing each signal, color (c) and luminance

(y) independently of each other through

separate cables.

NTSC

Dolby Digital

Acronym that stands for National Television

Systems Committee and the name of the

current analog broadcasting standards.

The system developed by Dolby Labora-

tories to compress digital sound. It offers

stereo sound (2ch) or multi-channel audio

(up to 5.1ch).

5CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125.

Cable companies often designate channels with letters or letter-number

combinations. Please check with your local cable company.

The following is a chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

W+1 W+2 W+3 W+4 W+5 W+6

37 39 40 41 42

CATV channel

TV Display

W+7 W+8 W+9 W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24 W+25 W+26 W+27

43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39 W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48

64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

W+49 W+50 W+51 W+52 W+53 W+54 W+55 W+56 W+57 W+58 A-5 A-4 A-3 A-2 A-1 W+59 W+60 W+61 W+62 W+63 W+64

85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105

CATV channel

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79 W+80 W+81 W+82 W+83 W+84

106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125

5MAINTENANCE

CABINET CLEANING

IR SIGNAL CHECK

• Wipe the front panel and other exterior surfaces of the TV with a soft

cloth immersed in lukewarm water and wrung dry.

• Never use a solvent or alcohol. Do not spray insecticide liquid near the

TV. Such chemicals may cause damage and discoloration to the exposed

surfaces.

If the remote control is not working properly, you can use an AM radio or

digital camera (including a cellular phone with built-in camera) to see if it

is sending out an infrared signal.

• With an AM radio:

Tune the AM radio station to a non-broadcasting

frequency. Point the remote control towards it,

push any button and listen. If the sound from

the radio ﬂutters, it is receiving the remote

control’s infrared signal.

LCD CLEANING

• Wipe the LCD of the TV with a soft cloth. Before cleaning the LCD, discon-

nect the power cord.

• With a digital camera

SERVICING

(including built-in cell phone cameras)

Point a digital camera

Should your unit become inoperative, do not try to correct the problem

yourself. There are no user serviceable parts inside. Turn oﬀ the TV, unplug

the power cord and call our toll free customer support line found on the

cover of this manual to locate an authorized service center.

towards the remote control. Push any button on the

remote control and look through the digital camera.

If the infrared light appears through the camera, the

remote control is working.

Download from Www.Somanuals.com. All Manuals Search And Download.

NFORMATION

5GENERAL SPECIFICATIONS

5ELECTRICAL SPECIFICATION

Sound Output:

5W, 8 ohm x 2

Television System: ATSC / NTSC-M TV Standard

5OTHER SPECIFICATIONS

Closed Caption:

System:

Remote Control:

Digital encoded

§15.122/FCC (Digital CC)

§15.119/FCC (Analog CC)

infrared light system

Operating Temperature:

41°F (5°C) to 104°F (40°C)

Channel Coverage (ATSC/NTSC):

VHF: 2 ~ 13

UHF: 14 ~ 69

CATV: 2 ~ 13, A ~ W, W+1 ~ W+94,

Power Requirements:

120 V AC +/- 10%, 60 Hz +/- 0.5%

A-5 ~ A-1, 5A

Tuning System:

Channel Access:

Channel frequency

Power Consumption(Maximum):

150W (standby: 1.0 W)

synthesized tuning system

Direct access keyboard,

Programmable scan, and Up/down

LCD:

26" wide XGA panel

(1,366 x 768 pixels)

Terminals:

Antenna Input:

VHF/UHF/CATV

Dimensions:

75 ohm unbalanced (F-type)

Mini DIN 4-pin jack x 2

RCA jack x 2

: 20-5/8" (523.5mm)

: 27-15/16" (710mm)

: 4-1/2" (114.5mm)

S-Video Input:

Video Input:

Audio Input:

RCA jack (L/R) x 4

Component Video/Audio Input:

: 22-5/8" (574mm)

: 27-15/16" (710mm)

: 10-13/16" (275mm)

One pin jack (Y) / 1Vpp x 2

Two pin jacks (Pb/Pr) / 700mVpp x 4

RCA jack (L/R) x 4

HDMI/Audio Input: HDMI jack

Weight:

30.8 lbs. (14kg)

RCA jack (L/R) x 2

Coaxial Digital Audio Output:

One pin jack, 500mVpp

Analog Audio Output:

RCA jack (L/R) x 2

Stereo Sound System Speaker

DVD

Discs (Playback compatibility):

DVD Video, DVD-RW/-R,

DVD+RW/+R, Audio CD, CD-RW/-R

Frequency response:

DVD (linear sound): 20 Hz to 20 kHz (sample rate: 48 kHz)

20 Hz to 44 kHz (sample rate: 96 kHz)

20 Hz to 20 kHz

CD:

Signal-to-noise ratio (S/N ratio):

CD:

90 dB (JEITA)

Dynamic range:

DVD (linear sound): 86 dB

CD:

86 dB (JEITA)

Total distortion factor:

DVD:

CD:

1 KHz 0.008% (JEITA)

• Designs and speciﬁcations are subject to change without notice and

without our legal obligation.

• If there is a discrepancy between languages, the default language will

be English.

Wow and ﬂutter:

Below the measurement limitation

(+/-0.001% W PEAK) (JEITA)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPAÑOL

ESPAÑOL

5FUNCIONES DEL MANDO A DISTANCIA

Botón INPUT SELECT

19. Botón CLEAR

Presiónelo para acceder a aparatos externos conecta-

dos, tales como un grabador de DVD o una VCR.

Botón POWER (pág.55)

•

Para borrar los números introducidos incorrectamente.

• Para cancelar el punto A para repetición A-B

(DVD, CD).

Para encender y apagar el TV/DVD.

Botones de Número de canal (pág.57)

• Para seleccionar canales.

• Para eliminar el número de la pista en la intro-

ducción de programas (CD, MP3, JPEG).

20. Botón REPEAT

•

Para introducir número de título, capítulo o pista.

Para reproducir un capítulo o título (DVD), pista, disco

(CD, MP3, JPEG) o grupo (MP3, JPEG) repetidamente.

Botón SETUP (pág.56)

Para mostrar el menú en pantalla.

Botón ENTER (pág.55)

21. Botón A-B

Para repetir entre el punto A y B seleccionado (DVD, CD).

22. Botón TITLE (pág.58)

Para activar la lista de títulos (DVD).

23. Botón PLAY B (pág.58)

Para comenzar la reproducción del disco.

24. Botón STOP C (pág.58)

Para interrumpir la reproducción del disco.

25. Botones REV E / FWD D (pág.59)

Para comenzar la reproducción de avance lento o

retroceso lento durante el modo pausa (DVD) y la

búsqueda adelante y atrás en un disco.

26. Botones CH K/L (pág.56)

Para seleccionar los canales y el modo de entrada externo.

27. Botón INFO

Para decidir los comandos de ajuste cuando apa-

rezca el menú.

Botones

K / L (pág.55)

Para desplazarse por los elementos a izquierda/

derecha/arriba/abajo.

Botón BACK//RETURN (pág.59)

Para volver a la operación anterior en el menú.

Botón CH RETURN

Para volver al canal que se estaba viendo antes.

Botón VOL. X/Y

Para ajustar el volumen.

10. Botón MUTE

Para desactivar y activar el sonido.

11. Botones SKIP H /

• Modo analógico (TV)

Para saltar adelante o atrás en capítulos, títulos (DVD),

pistas (CD, MP3, JPEG) o carpetas (MP3, JPEG).

12. Botón PAUSE (pág.58)

Para mostrar el número de canal, tipo de señal

y ajuste de TV.

• Modo digital (DTV)

Para hacer pausa en la reproducción del disco.

13. Botón DISC MENU (pág.58 /pág.59)

Para activar el menú en un disco (DVD) o LISTA

DE ARCHIVOS (MP3, JPEG).

Para mostrar la información de canal, tipo de

señal y ajuste de TV.

• Modo externo

Para mostrar modo externo, tipo de señal y

ajuste de TV.

14. Botón MODE

•

Para activar“LISTA DE CARPETA”de un disco cuan-

do“REPROD. DOBLE”está en“ENC.”(MP3, JPEG).

Para establecer el orden de reproducción o repro-

ducir aleatoriamente (CD, MP3, JPEG).

Para establecer el nivel de negro (DVD) y activar o

desactivar el sonido envolvente virtual (DVD, CD, MP3).

• Modo DVD

Para visualizar el estado actual (DVD, CD, MP3,

JPEG).

28. Botón SCREEN MODE

Selecciona las relaciones de aspecto disponibles

para la pantalla.

15. Botón SEARCH MODE

• Para buscar capítulo, título (DVD), tiempo (DVD,

CD) o pista (CD, MP3, JPEG).

29. Botón SLEEP

Para apagar automáticamente el aparato a la

hora prefijada.

16. Botón SUBTITLE

30. Botón AUDIO

Para seleccionar los subtítulos en un disco (DVD).

17. Botón ANGLE

• Modo analógico (TV)

Para seleccionar el modo audio.

• Modo digital (DTV)

Para cambiar el ángulo de cámara para ver la

secuencia reproducida desde un ángulo dife-

rente (DVD).

Para seleccionar el idioma de audio.

• Modo DVD

18. Botón ZOOM

Para seleccionar el idioma de audio (DVD) o el

modo de sonido (CD).

Para magnificar una parte de la imagen (2X y 4X:

DVD, 2X: JPEG).

31. Botón EJECT (pág.58)

Para expulsar el disco.

NOTA:

• Con los botones [VOL. X/Y] o [MUTE], solamente puede ajustar el volumen de la unidad principal. No puede ajustar el volumen de los dis-

positivos externos con estos botones.

• A menos que se indique lo contario, todas las operaciones descritas se basan en la utilización de un mando a distancia.

5INSTALACIÓN DE LAS PILAS

Coloque las dos pilas AA (incluídas) haciendo coincidir la polaridad (++/--) indicada dentro del compartimento del

^{mando a}1^distancia.

PRECAUCIONES RELACIONADAS CON LAS PILAS:

• Asegúrese de respetar la polaridad correcta como se indica en el compartimiento de las pilas.

Si invierte las pilas puede causar daño al dispositivo.

• No combine tipos diferentes de pilas. (por ej., Alcalinas y Carbón-Zinc) o pilas usadas con pilas nuevas.

• Sí el dispositivo no se usará por un periodo largo, se deben retirar las pilas para evitar daños o lesiones causadas por el posible derrame del

ácido en su interior.

• No intente recargar pilas que no están diseñadas para ese fin, ya que pueden sobrecalentarse y agrietarse.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPAÑOL

5PANEL DE CONTROL

1. Botón SETUP (pág.56)

Para ver el menú en pantalla.

2. Botón STOP C (pág.58)

Para interrumpir la reproducción del disco.

3. Botón PLAY B (pág.58)

DVD CONTROL

STOP

PLAY

SKIP

EJECT

Para comenzar la reproducción del disco.

4. Botones SKIP H /

Para saltar capítulos, títulos (DVD), o pistas (CD, MP3 o JPEG).

5. Botón EJECT A (pág.58)

INPUT SELECT/

ENTER

SETUP

POWER

VOLUME

CHANNEL

TV CONTROL

Para expulsar el disco.

6. Botón POWER (pág.55)

Para encender y apagar el TV/DVD.

7. Botón INPUT SELECT / ENTER (pág.55)

• Para acceder a aparatos externos conectados, tales como un

grabador de DVD o una VCR.

• Para decidir el comando de ajuste cuando aparezca el menú.

8. Botones CHANNEL K/L

Para seleccionar canales y desplazarse arriba/abajo por los

elementos del menú.

9. Botones VOLUME X/Y

Para ajustar el volumen y desplazarse a derecha(X)/izquierda(Y)

por los elementos del menú.

10. Ventana del sensor de infrarrojos

STANDBY

POWER ON

Para recibir los rayos infrarrojos trasmitidos desde el mando a

distancia.

NOTA:

• Con los botones [VOLUME X/Y], solamente puede ajustar el

volumen de la unidad principal. No puede ajustar el

volumen de los dispositivos externos con estos botones.

5PANEL TRASERO

1. Toma ANT. IN (pág.51)

Conexión de cable coaxial a su antena o su caja de cable.

2. Toma DIGITAL AUDIO OUT (COAXIAL) (pág.54)

Conexión de cable coaxial de audio digital a un decodificador o

receptor de audio. Conecte el cable a la toma de entrada audio

digital del aparato externo.

3. Tomas AUDIO OUT (pág.54)

Conexión de cable de audio a dispositivos de audio externos.

Utilice las tomas de entrada audio del aparato externo.

4. Tomas de entrada AUDIO (para conexión DVI) (pág.52)

Conexión de cable de audio a aparatos de audio/vídeo externos

con toma DVI. Utilice las tomas de entrada audio del dispositivo

externo al usar un cable de conversión HDMI-DVI.

5. Toma HDMI IN (pág.52)

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

HDMI

desde abajo

Parte trasera del TV

Conexión de cable HDMI a aparatos de vídeo externos (es decir,

grabador de DVD).

VIDEO

DIGITAL

AUDIO OUT

(COAXIAL)

ANT. IN

AUDIO OUT AUDIO

AUDIO

S-VIDEO1

S-VIDEO2

HDMI IN

HDMI

COMPONENT2

COMPONENT1

VIDEO1

INNER JACKS

6. Toma de entrada S-VIDEO1 (pág.53)

Conexión de cable S-Vídeo y de cable de audio (VIDEO1) a dis-

positivos de vídeo externos.

7. Toma de entrada S-VIDEO2 (pág.53)

Conexión de cable S-Vídeo y de cable de audio (VIDEO2) a dis-

positivos de vídeo externos.

desde abajo

8. Tomas de entrada VIDEO1 y AUDIO (pág.54)

Conexión de cable de vídeo y de audio a dispositivos externos.

9. Tomas de entrada VIDEO2 y AUDIO (pág.54)

Conexión de cable de vídeo y de audio a dispositivos externos.

10. Tomas de entrada COMPONENT1 y AUDIO (pág.53)

Conexión de cable de componentes a dispositivos de audio/

vídeo externos. Utilice las tomas de salida de componentes y de

audio del dispositivo externo.

11. Tomas de entrada COMPONENT2 y AUDIO (pág.53)

Conexión de cable de componentes a dispositivos de audio/

vídeo externos. Utilice las tomas de salida de componentes y de

audio del dispositivo externo.

VIDEO

S-VIDEO1

S-VIDEO2

AUDIO

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

Download from Www.Somanuals.com. All Manuals Search And Download.

5CONEXIÓN

Esta sección describe cómo conectar el televisor a una antena, caja de cable, etc.

ASEGÚRESE DE TENER UNA ANTENA.

Como el DTV sólo existe en ondas aéreas, necesita una antena para recibir señal digital.

NOTA:

• Asegúrese de que la antena o la otra fuente esté bien conectada antes de enchufar el cable de alimentación.

[CONEXIÓN DE CABLE DE ANTENA]

1) Para conectar el televisor a una antena

Conecte el cable coaxial de televisión de su casa a la toma ANT.IN del TV.

2) Cuando se conecta el TV a la empresa del TV cable (sin caja)

Conecte el cable coaxial de televisión de su casa a la toma ANT.IN del TV.

Antena de

VHF / UHF

Parte trasera del TV

Cable coaxial

(no incluído)

ANT. IN

VIDEO

AUDIO

VIDEO

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

AUDIO OUT AUDIO

AUDIO

S-VIDEO1

S-VIDEO2

HDMI IN

HDMI

COMPONENT2

COMPONENT1

VIDEO1

INNER JACKS

Cable coaxial

Empresa del

TV cable

(no incluído)

*Una vez hechas las conexiones, encienda el TV y empiece con los ajustes iniciales.

La exploración de canales es necesaria para que el TV memorice todos los canales disponibles en su zona.

(Consulte el "PREAJUSTES INICIAL" en la página 55.)

NOTA:

• Para su seguridad y con el fin de evitar daños al equipo, por favor desenchufe el cable coaxial de la toma ANT.IN antes de trasladar la unidad.

• Si utiliza una antena para recibir TV analógica, la misma antena permitirá recibir la DTV.

Las antenas exteriores o en el techo serán más efectivas que la versiones encima del aparato de TV.

• Para cambiar fácilmente entre los cables de antena y de cable puede comprar un selector de antena (no incluído).

• Si desea conectar el sistema de cable directamente, póngase en contacto con el instalador del sistema CATV.

[CONEXIÓN CON CAJA DE CONVERTIDOR/CAJA DE SATÉLITE]

1) Conecte el cable coaxial de la toma de su casa al conector de entrada de la caja de CABLE/SATÉLITE.

2) Utilice otro cable coaxial para conectar la toma ANT.IN de su televisor a la toma de salida de la caja de CABLE/

SATÉLITE.

EX.

Parte trasera del TV

Plato del

satélite

Caja de Cable o

caja de Satélite

VIDEO

AUDIO

VIDEO

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

ANT. IN

AUDIO OUT AUDIO

AUDIO

S-VIDEO1

S-VIDEO2

HDMI IN

HDMI

Cable coaxial

COMPONENT2

COMPONENT1

VIDEO1

INNER JACKS

Empresa del

TV cable

(no incluído)

*Los cables necesarios en 2) y los métodos de conexión varían según la caja de CABLE/SATÉLITE.

Para más información, póngase en contacto con su proveedor de cable/satélite.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPAÑOL

5CONEXIÓN DE OTROS DISPOSITIVOS

[HDMI]

1) El sistema HDMI (Interfaz Multimedia de Alta Definición) incorpora la tecnología más avanzada para asegurar que

la señal mantiene el mayor grado de intensidad posible desde la fuente al televisor. Tanto el vídeo como el audio

viajan a través de un único cable.

Cable HDMI

A toma de HDMI IN

(no incluído)

EX.

HDMI OUT

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

A toma de salida HDMI

Grabador de DVD con

la toma de salida HDMI

HDMI

Parte trasera del TV

NOTA:

• Este TV acepta señales de vídeo de 480i / 480p / 720p / 1080i, y señales de audio de 32 kHz / 44,1 kHz / 48 kHz.

• Este TV acepta solamente señal de audio de dos canales (LPCM).

• Necesita seleccionar "PCM" para la salida de audio digital del dispositivo que conecte o para el ajuste de audio HDMI. El audio a veces no

emite sonidos si selecciona "Bitstream", etc.

• Este TV solamente acepta señales correspondientes a EIA861.

2) Si su aparato de vídeo tiene una toma de salida DVI, conecte el cable de conversión HDMI (no incluído) desde la

toma de salida DVI.

Cable de conversión HDMI-DVI

(no incluído)

A toma de HDMI IN

A toma de salida DVI

EX.

DVI OUT

ANT. IN

AUDIO OUT

AUDIO

AUDIO OUT

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

Caja de Cable o caja de Satélite

con la toma de salida DVI

HDMI

A tomas de

salida de audio

Parte trasera

del TV

A tomas de

entrada de

AUDIO

Cable de audio

(no incluído)

NOTA:

• Este TV acepta señales de vídeo de 480i / 480p / 720p / 1080i.

• Un cable de conversión HDMI requiere asimismo una conexión aparte de cable de audio.

• Las señales de audio se convierten de señal digital a señal analógica si se establece una conexión como se indica en el párrafo 2) de arriba.

• DVI no muestra imagen si la señal 480i no acepta EIA/CEA-861/861B.

“HDMI el logotipo HDMI y High-Definition Multimedia Interface (Interface de Multimedios

de Alta Definición) son marcas comerciales o marcas registradas de HDMI Licensing LLC.”

Download from Www.Somanuals.com. All Manuals Search And Download.

[CONEXIÓN DE CABLE DE COMPONENTES]

Ofrece una mejor calidad de imagen para dispositivos de vídeo conectados a su TV.

Utilice un cable conector de vídeo componente (no incluído) para conectar su TV a dispositivos externos de

vídeo equipados con tomas de vídeo componentes.

Si conecta las tomas de salida componente a la toma de entrada COMPONENT1, conecte un cable de audio a las

tomas AUDIO L/R (izquierda/derecha) de COMPONENT1.

Si conecta las tomas de salida componente a la toma de entrada COMPONENT2, conecte un cable de audio a las

tomas AUDIO L/R (izquierda/derecha) de COMPONENT2.

Cable de vídeo componente

(no incluído)

A tomas de entrada

de COMPONENT1

A tomas de salida de vídeo

componente

EX.

VIDEO

S-VIDEO1

S-VIDEO2

Grabador de DVD con las tomas

de salida de vídeo componente

AUDIO

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

A tomas de

salida de audio

Parte trasera del TV

A tomas de entrada

de AUDIO

Cable de audio

(no incluído)

NOTA:

• Este TV acepta señales de vídeo de 480i / 480p / 720p / 1080i.

[CONEXIÓN DE CABLE DE S-VÍDEO]

Ofrece una buena calidad de imagen para dispositivos de vídeo conectados a su TV.

Utilice un cable S-video (no incluído) para conectar su TV a dispositivos externos de vídeo equipados con

conectores S-video.

Si conecta la toma de salida S-Video a la toma de entrada S-VIDEO1, conecte un cable de audio a las tomas AUDIO L/R

(izquierda/derecha) de VIDEO1.

Si conecta la toma de salida S-Video a la toma de entrada S-VIDEO2, conecte un cable de audio a las tomas AUDIO L/R

(izquierda/derecha) de VIDEO2.

A toma de entrada

de S-VIDEO1

Cable S-Video

(no incluído)

A toma de salida

de S-Video

VIDEO

EX.

AUDIO

OUT

VIDEO S-VIDEO

OUT OUT

S-VIDEO1

S-VIDEO2

AUDIO

Grabador de DVD con la toma de

salida S-Video

A tomas de salida

de audio

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

Parte trasera

del TV

A tomas de

entrada de

AUDIO

Cable de audio

(no incluído)

NOTA:

• Si se conecta al mismo tiempo al conector S-video y al conector VIDEO será la conexión del S-Video la que tenga prioridad.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPAÑOL

[CONEXIÓN DE VÍDEO]

Ofrece una calidad de imagen estándar para dispositivos de vídeo conectados al televisor.

Cuando la toma de audio del dispositivo de vídeo es monoaural, conecte el cable de audio a la toma deentrada de audio L.

Si conecta las tomas de salida componente a la toma de entrada VIDEO1, conecte un cable de audio a las tomas

AUDIO L/R (izquierda/derecha) de VIDEO1.

Si conecta las tomas de salida componente a la toma de entrada VIDEO2, conecte un cable de audio a las tomas

AUDIO L/R (izquierda/derecha) de VIDEO2.

Cable de vídeo

A toma de entrada

(no incluído)

de VIDEO1

EX.

A toma de

VIDEO

salida de

vídeo

AUDIO

OUT

VIDEO

OUT

S-VIDEO1

S-VIDEO2

Videocámara

Videojuegos

AUDIO

A tomas de

salida de audio

COMPONENT2

COMPONENT1

VIDEO2

VIDEO1

VCR

A tomas de

entrada de

AUDIO

Parte trasera

del TV

Cable de audio

(no incluído)

[CONEXIÓN DE SALIDA DE AUDIO DIGITAL]

Si conecta este televisor a un dispositivo de audio digital externo, podrá disfrutar de audio multicanal, comopor ejem-

plo el sonido de transmisión digital de 5.1 canales. No se incluye el cable coaxial de audio digital requerido.

EX.

Cable coaxial de audio digital

(no incluído)

A toma de

DIGITAL AUDIO OUT

MD deck, DAT deck, etc.

COAXIAL

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

A toma de entrada

coaxial de audio digital

HDMI

Parte trasera del TV

Descodiﬁcador Dolby Digital

Fabricado bajo licencia de Dolby Laboratories. “Dolby” y el símbolo de la doble D

son marcas comerciales de Dolby Laboratories.

[CONEXIÓN DE SALIDA DE AUDIO ANALÓGICA]

Si conecta este televisor a un dispositivo de audio analógico externo, podrá disfrutar de sonido estereofónico(2 cana-

les).No se incluye el cable de audio requerido.

AUDIO

EX.

ANT. IN

AUDIO OUT

AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

HDMI IN

A tomas de

entrada de

audio

HDMI

Sistema estereofónico

Parte trasera del TV

A tomas de

AUDIO OUT

Cable de audio

(no incluído)

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTA:

5PREAJUSTES INICIAL

• La función de Autoscan inicial puede ejecutarse para "Aire"

o para "Cable" solamente una vez. Cuando cambie la con-

exión (Aire/Cable), ajuste de nuevo "Autoscan". (Consulte la

página 56.)

Esta sección le guiará en la instalación inicial de su televisor, que entre

otras cosas requiere seleccionar el idioma para el menú en pantalla y la

operación AUTOSCAN, que escanea y memoriza los canales visualizables

automáticamente.

• Si se conecta al sistema de cable directamente, póngase en

contacto con el instalador de sistema de CATV.

• Cuando no termine la exploración, Sugerencias Útiles se

visualizará cada vez que usted conecte la alimentación.

Si ha registrado canales previamente cuando aparece

esta pantalla, puede acceder a ellos con [los botones de

número].

Una vez hechas todas las conexiones necesarias, enci-

enda este TV.

Presione [POWER] para visualizar el menú de ajuste

inicial.

2-0

No channel is registered.

Press and hold "ENTER" key for 3 seconds.

Contact support hotline provided on manual or back of unit.

Sin canal registrado.

Mantenga oprimida la tecla "ENTER" durante 3 segundos.

Llame teléfono de apoyo en manual o atrás de TV.

• Esta operación puede tardar unos momentos en empezar.

• Si el menú de Ajuste Inicial no aparece, mantenga

presionado [ENTER] durante 3 segundos, para que

aparezca el ajuste inicial y luego pase al paso 3.

Si ya ha completado el ajuste inicial, consulte

"SELECCIÓN DE IDIOMA" en página 57.

Pas de chaîne consign.

Maintenir la touche "ENTER" pressée 3 secondes.

Contacter numero d'urgence dans manuel ou arrière appareil.

• El número de teléfono del centro de servicio está indicado

en la portada de este manual.

Al encender el televisor por primera vez, aparecerá la

siguiente pantalla. Utilice [

] para seleccionar el

idioma del menú en pantalla entre las opciones que

aparecen en el margen derecho de la pantalla.

(English / Español / Français)

Initial Setup

Select the language for setup display.

Elija idioma de preparación.

English

Español

Français

Sélectionner langue écran config.

^SETUPExit

ENTER

Select

Enter

• Aparecerá en pantalla la confirmación de antena en

el paso 4 en el idioma seleccionado después de pre-

sionar [ENTER].

Utilice [

] para seleccionar la fuente de la toma

ANT-IN, y presione [ENTER].

Preparación Inicial

Confirme que antena está conectada a toma "ANT IN".

Elija el destino de la toma "ANT IN".

Aire

Cable

Aire

Cable

ANT IN

BACK

ENTER

Seleccionar

Entre

Atrás

^SETUPSalir

Autoscan se iniciará automáticamente.

Preparación Inicial

Sistema escanea canales, espere.

Canales analógicos

Canales digitales

1ca

0ca

^SETUPSalir

• Cuando se haya terminado la exploración, se mostrará el

canal memorizado más pequeño.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPAÑOL

5PREA. AUTO CA.

5LISTA DE CANALES

Con la función AUTOSCAN, el televisor escanea y memoriza automática-

mente los canales visualizables en su zona. Active la función AUTOSCAN al

encender el televisor por primera vez, al cambiar las fuentes de transmisión

(por ej., de antena a televisión por cable), o al trasladar el televisor a una

zona de transmisión diferente.

Esta función le permite eliminar canales no deseados de la lista de registro

de canales.

Presione [SETUP] para visualizar la pantalla de ajuste.

SALIR

IMAGEN

CANAL

DETALLE

IDIOMA

DVD

IDIOMA

DVD

Utilice [

] para seleccionar “CANAL”, y presione

Utilice [

] para seleccionar “CANAL”, y presione

[ENTER].

Utilice [

] para seleccionar “Autoscan”, y presione

Utilice [

] para seleccionar “Lista Canales”, y pre-

[ENTER].

sione [ENTER].

Canal

SALIR

Autoscan

IMAGEN

Lista Canales

Registro Manual

Antena

Registro Manual

CANAL

DETALLE

IDIOMA

DVD

Antena

DETALLE

IDIOMA

DVD

Utilice [

nar.

] para seleccionar el canal que desee elimi-

Utilice [

] para seleccionar “Aire” para canales de TV

o “Cable“ para canales CATV, y presione [ENTER].

Lista Canales

Autoscan

SALIR

Subraye canales para selección

Ch Up/Down.

DTV

Atrás

Aire

Autoscan volverá a explorar

todos los canales.

IMAGEN

Puede llevar un poco de tiempo en

completarse.

Cable

CANAL

DETALLE

IDIOMA

DVD

CANAL

DETALLE

IDIOMA

DVD

Elija el destino de la toma "ANT IN".

Aire

Cable

1hora

DTV

Cable

DTV

ANT IN

BACK

ENTER

Selección Ca

Ver/Saltar

Atrás

• Presione [ENTER] para resaltar el canal seleccionado

• Se iniciará automáticamente la búsqueda y memo-

rización de los canales.

para su eliminación. No podrá volver a seleccionar el

canal con [CH

Sistema escanea canales, espere.

• Para reactivar el canal eliminado, resáltelo y presione

[ENTER].

• Al eliminar un canal principal, se eliminan también

sus canales asociados.

72%

Canales analógicos

Canales digitales

10ca

6ca

^SETUPSalir

NOTA:

• El canal con "DTV" indicado en la pantalla es ATSC, de lo

contrario el canal es NTSC.

• Cuando finalice este proceso, se mostrará el canal más

pequeño memorizado de la emisión.

• En la radiodifusión DTV, a veces un canal emite múltiples

programas dependiendo de la hora de emisión. En este

caso, el canal principal se conoce como canal mayor y el

subcanal como canal menor.

NOTA:

• Asegúrese que el TV está conectado a la antena o cable.

• Si desea conectar el sistema de cable directamente, pón-

gase en contacto con el instalador del sistema CATV.

• Si presiona [POWER] o [SETUP] durante Autoscan, se can-

celará este ajuste.

Para salir del instalación, presione [SETUP].

• Si no hay recepción o si se detecta una señal deficiente,

aparecerá una Sugerencia en pantalla al finalizar la explor-

ación.

Download from Www.Somanuals.com. All Manuals Search And Download.

5REGISTRO MANUAL

5SELECCIÓN DE IDIOMA

Esta función le permite añadir manualmente canales no memorizados

durante la operación de AUTOSCAN debido a la poca fuerza de la señal de

transmisión.

Puede elegir su idioma de pantalla entre los siguientes: Inglés, Español o

Francés.

Presione [SETUP] para visualizar la pantalla de ajuste.

SALIR

IMAGEN

CANAL

DETALLE

IDIOMA

DVD

IDIOMA

DVD

Utilice [

] para seleccionar “CANAL”, y presione

Utilice [

] para seleccionar “IDIOMA”, y presione

[ENTER].

Utilice [

] para seleccionar “Registo Manual”, y pre-

Utilice [

] para seleccionar su idioma, y presione

sione [ENTER].

[ENTER].

Idioma

SALIR

Canal

English

Español

Français

Select the language for setup.display.

Elija idioma de preparación.

SALIR

IMAGEN

Autoscan

IMAGEN

CANAL

DETALLE

IDIOMA

DVD

Lista Canales

Registro Manual

Antena

Sélectionner langue écran config.

CANAL

DETALLE

IDIOMA

DVD

Utilice [los botones de número] para seleccionar el

canal que desea añadir, y presione [ENTER].

Para salir del instalación, presione [SETUP].

Registro Manual

SALIR

Registra

Para los canales analógicos,

seleccione un canal a registrar con

la tecla unmérica.

IMAGEN

Para los canales digitales, debe

realizer la función Autoscan.

CANAL

DETALLE

IDIOMA

DVD

BACK

Atrás

Cambia Ca

Para salir del instalación, presione [SETUP].

NOTA:

• Si la configuración se realiza con éxito, aparecerá en

pantalla "Registro en lista canales".

• Si la configuración no se realiza con éxito, como en caso de

utilizarse Video1, aparece en la pantalla "No disponible".

Download from Www.Somanuals.com. All Manuals Search And Download.

SPAÑOL

Estas operaciones son controlables desde el mando a distancia. Algunas de ellas también son controlables desde el panel de mando del aparato principal.

5REPRODUCCIÓN

5MENÚ DVD

DVD

MP3

JPEG

(

en página 59)

DVD

Antes:

Algunos discos DVD contienen menús que le permiten per-

sonalizar la reproducción del DVD.

Encienda el ampliﬁcador y cualquier otro equipo que esté conectado a esta

unidad.

• Presione [DISC MENU] y utilice [K / L / s / B] para

seleccionar un elemento y a continuación presione

[ENTER] (o [PLAY B]).

Asegúrese de que el receptor de audio externo (no incluido) está ajustado

en el canal correcto.

Presione [POWER] para encender la unidad.

Activar una pantalla de Menú durante la reproducción

• Presione [DISC MENU] para activar el menú DVD.

• Presione [TITLE] para activar el menú de título.

NOTA:

Inserte un disco con la etiqueta orientada hacia a la

izquierda desde el lateral derecho de la unidad.

• Las operaciones de menú pueden variar según el disco.

Para más detalles, consulte el manual del disco.

etiquet

5REANUDACIÓN

DVD

MP3

JPEG

Presione [STOP C] durante la

REANUDACIÓN ACTIVADA

reproducción. En la pantalla del

televisor aparecerá el mensaje

de reanudación.

Presione 'PLAY' para reproducir

desde aquí.

Para reproducir desde el inicio,

primero presione 'STOP' y luego 'PLAY'.

La unidad pasa al modo DVD cuando estaba en modo

TV y detecta el tipo de disco.

Presione [PLAY B] para reanu-

dar la reproducción desde el

punto en que se interrumpió..

DVD

NOTA:

•

Para cancelar la información de reanudación, presione de nuevo

[STOP C] en el modo de parada . En algunos discos, [STOP C] no

funcionará mientras se muestra el mensaje de reanudación. Espere

hasta que el mensaje desaparezca.

e.g.) disco DVD

• Presione [PLAY B] si la unidad no pasa al modo DVD.

• La información de reanudación se guardará incluso cuando

la unidad se encuentre en modo de espera. En MP3 y JPEG, la

reproducción se reanudará desde el comienzo de la pista en la

que se interrumpió la reproducción.

El disco comienza la reproducción.

PAUSA Y REPRODUCCIÓN PASO A PASO

Presione [STOP C] para interrumpir la reproducción.

DVD

MP3

JPEG

Presione [PAUSE F] durante la reproducción.

• La reproducción se pondrá en pausa y el sonido se

silenciará.

• Presione [PAUSE F] una vez durante la

reproducción doble/carpeta para poner en

pausa un archivo JPEG solamente. Presione

[PAUSE F] nuevamente para poner en

pausa una pista MP3.

Presione [EJECT] para expulsar el disco.

NOTA:

• Para reproducir un disco en formato MP3 o JPEG, consulte los

detalles en página 59.

Para continuar la reproducción, presione [PLAY B].

• Puede aparecer un “icono prohibido” en la

zona superior derecha de la pantalla del

televisor cuando la operación esté prohibida

por el disco o por esta unidad.

• Algunos discos DVD pueden iniciar la reproducción desde el

título 2 ó 3 debido a programas específicos.

• Durante la reproducción de un disco de 2 capas, las imágenes

pueden interrumpirse durante un instante. Esto sucede mien-

tras la primera capa se está cambiando a la segunda capa.

Esto no es un fallo de funcionamiento.

DVD

El disco avanza fotograma a fotograma cada vez que se

presiona [PAUSE F] en el modo de pausa.

Para continuar la reproducción, presione [PLAY B].

NOTA:

• Ajuste “MODO VISTA FIJA” en “IMAGEN”, en el ajuste “OTROS”, si

las imágenes aparecen borrosas en el modo de pausa.

Download from Www.Somanuals.com. All Manuals Search And Download.

AVANCE RÁPIDO / RETROCESO RÁPIDO 5REPRODUCCIÓN DE MP3, JPEG

MP3

JPEG

DVD

MP3

Presione [FWD D] o [REV E] repetidamente duran-

te la reproducción para seleccionar la velocidad de

avance o retroceso necesaria.

MP3 o JPEG son métodos de compresión de archivos. Puede copiar archivos

MP3 o JPEG en discos CD-RW/-R desde su ordenador y reproducir los archi-

vos en esta unidad.

Para continuar la reproducción, presione [PLAY B].

Inserte un disco en formato MP3 o JPEG, la reproduc-

ción empezará automáticamente.

• Presione [PLAY B] si ya se ha insertado un disco en

formato MP3 o JPEG.

• Presione [DISC MENU] cuando quiera activar la LISTA

DE ARCHIVOS.

Cuando seleccione la carpeta:

NOTA:

• Ajuste “MODO VISTA FIJA” en “IMAGEN”, en el ajuste “OTROS”, si

las imágenes aparecen borrosas en el modo de reproducción

rápida.

• La velocidad de búsqueda de avance o retroceso rápido es dife-

rente según el disco. La velocidad aproximada es 1(2X), 2(8X),

3(20X), 4(50X) y 5(100X) en discos DVD y 1(2X), 2(8X) y 3(30X) en

discos CD Audio y MP3.

• En discos CD Audio y MP3, el sonido se escuchará durante la

búsqueda de avance o retroceso rápido.

• Presione [ B] cuando quiera ir a la siguiente jerarquía.

LISTA DE ARCHIVOS

NOMBRE DE DISCO

FOLDER

MP3

JPEG

Nombre de carpeta

Nombre de archivo

AVANCE LENTO / RETROCESO LENTO

ENTER

PLAY

Nombre de carpeta

DVD

Presione [FWD D] o [REV E] repetidamente duran-

te el modo de pausa para seleccionar la velocidad de

avance o retroceso necesaria.

• Presione [s] cuando quiera volver a la jerarquía ante-

rior (excepto la jerarquía de primer nivel).

• Si se presiona [TITLE] cuando se visualiza una LISTA

DE ARCHIVOS, se resaltará el primer elemento de la

jerarquía de primer nivel.

Para continuar la reproducción, presione [PLAY B].

NOTA:

• La velocidad de avance o retroceso lentos varía según el disco.

La velocidad aproximada es 1 (1/16), 2 (1/8) y 3 (1/2).

• Presione [DISC MENU] o [BACK/RETURN] para volver

• Ajuste “MODO VISTA FIJA” en “IMAGEN”, en el ajuste “OTROS”, si

las imágenes aparecen borrosas en el modo de reproducción

lenta.

a la pantalla de reproducción.

Presione [STOP C] una vez para interrumpir la repro-

ducción temporalmente.

• Consulte “REANUDACIÓN” en página 58.

NOTA:

• Algunas selecciones pueden tardar un tiempo en ser reconocidas.

•

Las carpetas son conocidas como Grupos; los archivos son conocidos como Pistas.

• Las carpetas, archivos MP3 y archivos JPEG se visualizan respectiv-

amente como

•

En un disco pueden reconocerse un máximo de 255 carpetas o 999 archivos.

En una carpeta pueden reconocerse hasta 8 jerarquías. Los archivos situa-

dos en las carpetas novena o más profundas no pueden reproducirse.

• Esta unidad puede reproducir imágenes y sonidos desde datos

grabados en formatos MP3 y JPEG en discos CD-RW/-R.

•

Un archivo con una extensión “.mp3 (MP3)” se denomina “archivo MP3”.

• Un archivo con una extensión “.jpg (JPG)” o “.jpeg (JPEG)” se deno-

mina “archivo JPEG”.

• Exif es un formato de archivo, el formato “Exchangeable Image

File” (archivo de imagen intercambiable) creado por la Asociación

Japonesa de Desarrollo de la Industria Electrónica (JEIDA).

• Los archivos con extensión distinta de “.mp3 (MP3)”, “.jpg (JPG)” y

“.jpeg (JPEG)” no aparecerán en el menú MP3 o JPEG.

•

Si el archivo no está grabado en formato MP3 o JPEG, puede producirse

ruido incluso aunque la extensión del archivo esté en “.mp3 (MP3)”, “.jpg

(JPG)” o “.jpeg (JPEG)”.

El nombre de grupo y pista puede visualizarse en hasta 25 caracteres.

Los caracteres no reconocibles serán sustituidos por asteriscos.

• Los grupos o pistas no reproducibles pueden visualizarse,

según las condiciones de grabación.

• Los archivos JPEG progresivo (archivos JPEG guardados en

formato progresivo) no se reproducirán en esta unidad.

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workman-

ship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year

from the date of original retail purchase. Certain parts and LCD image burn-in are excluded

from this warranty.

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the

date of original retail purchase.

LABOR:

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR

OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO

OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,

missing or if service was attempted by an unauthorized service center. This limited warranty does not

apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occur during normal

use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, altera-

tions or products not supplied by FUNAI CORP., or damage, which results from accident, misuse, abuse,

mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such

as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or other

acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL),

ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,

INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE

INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING

THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY

DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.

THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO

PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE

CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY

FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN

SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:

To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its

original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE

CENTER. FUNAI CORP. will not reimburse you for any service done by unauthorized service providers with-

out prior written approval.

To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,

please contact us at:

FUNAI CORPORATION

Customer Service

Tel : 1-800-968-3429

http://www.SylvaniaConsumerElectronics.com

19900 Van Ness Avenue, Torrance, CA 90501

Printed in China

L4360UA / L4350UA

1EMN22057A ****

Download from Www.Somanuals.com. All Manuals Search And Download.

Shark Vacuum Cleaner MV3010 FS User Manual
Sony Car Satellite Radio System CDX GT550UI User Manual
Sony Cassette Player WM EQ3 User Manual
Sony Computer Accessories MSPSMS11000 User Manual
Sony Digital Camera 4 166 513 131 User Manual
State Industries Water Heater 197425 004 User Manual
Sunbeam Coffeemaker EM5800 User Manual
Sunbeam Electric Heater SFH090 User Manual
SUPER MICRO Computer Computer Hardware H8SCM User Manual
Tanita Scale TBF 611 User Manual