rm11.16.04
Peripheral Electronics®,
a division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
727-572-9255 or [email protected]
©2005 AAMP™ of Florida, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
CHAPTER
1
Intro
Thank you for purchasing the Aux2Car interface. This interface will allow you
to connect a line level audio input to you vehicle’s factory radio without the
use of a noisy RF modulator. The Aux2Car interface is the best way to add
mobile video, satellite radio, MP3 players or other hand held media devices to
your factory radio.
Installation Preparation
This chapter provides information required for the
installation of the Aux2Car adaptor, it must be read by all users.
Thank you for purchasing the Aux2Car adaptor. Since the Aux2Car
will work in many different vehicles the following steps must be taken
to ensure that it is set up correctly for the vehicle it is being installed in.
Before Installation
To prevent damage to your vehicle and the interface, take the following precau-
tions.
NOTE: If the vehicle is equipped with an on-board drive or navigation com-
puter, do not disconnect the battery cable If the battery cable is disconnected, the
computer memory may be lost. Under these conditions, use extra caution to avoid causing
a short circuit during installation. If your radio has a security code make sure you know the
code and how to enter it prior to removing the battery cable. The radio will require this code
to operate when the battery terminal is reconnected.
1.
Do not install the unit in the following locations:
A. Locations exposed to direct sunlight
B. Locations where hot air flows from the car’s heater
First Step (For All Vehicles)
The first and most important step in using the Aux2Car is setting the dip-switches on the
interface; this makes the Auxillary source compatible with the vehicle it is being installed in.
The Aux2Car adaptor will not work if this step is not followed correctly.
IMPORTANT!!! Dip Switch settings must be made while unit is unplugged from vehi-
cle. Changes to dip switch settings will not be recognized untill unit is powered down
then powered up again.
The dip switches can be found on the side of the interface which connects to the source.
Switches are in the “ON” position when they are switched down. Aux2Car settings for each
vehicle can be found on the vehicles installation page. Refer to the index to find the page
number within this manual that covers your vehicle.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
CHAPTER
2
Vehicle Installation
In this chapter you will learn how to install the Aux2Car adaptor in specific vehicles.
The Aux2Car adaptor connects to your car radio using a vehicle specific cable harness.
Browse to the specific section for your vehicle to learn what cable you need and how to
set up the Aux2Car and install in your vehicle. Below is an overview of all Aux2Car settings.
Dip-Switch Overview
The dip switches can be found on the side of the Aux2Car. Switches are in the “ON”
position when they are switched DOWN. Aux2Car settings for each vehicle can be
found on the vehicles installation page. Refer to the index to find the page number that
covers your vehicle.
Programming Dip Switch settings Quick Reference
1
2
3
4
5
6
7
8
Acura
Audi/VW
Ford
on
on
off
on
off
on
off
off
off
off
on
on
off
off
on
off
off
off
off
off
on
on
on
off
on
off
off
off
off
off
off
on
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
on
on
on
on
on
on
on
on
Ford Focus
GM E&C
GM Class 2
GM XM
Chrysler new
Chrysler
old/Honda
on
on
off
on
off
off
on
on
off
off
off
off
off
off
on
on
Toyota
Please consult vehicle specific section for important installation instructions
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
Acura
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
SETTINGS FOR
ALL ACURAS
1
2
3
4
5
6
7
8
on
off
off
on
off
off
off
on
• All Models (1992-2002) – Connector behind the radio, use the
PX HCH2 cable and the Aux2Car settings above.
• TL 1999 to 2002 use Honda cable behind the radio
• Acura NSX, SLX, and MDX (1996 and Up) – Not Compatible.
• Acura’s with navigation are not compatible.
OPERATION
Switch to the Aux2Car adaptor by pressing the CD button on the radio. This step may take
up to three minutes for the radio to initialize. Some radio models require pressing “Seek >”
once to start playing the auxillary source.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
Audi
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
Before connecting any cables to the Aux2Car you must set the dip switchs to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
1
2
3
4
5
6
7
8
on
off
off
off
off
off
off
on
• All Models (1998-2004) – Pre-wired 13-pin cable in the left-rear
trunk of all Audi vehicles use the PXHAD1
• Audi A8 (2003-2004) – Not Compatible.
• Audi A6 (2004) – Not Compatible.
OPERATION
Once you connect the Aux2Car adaptor, turn on your radio. A CD icon will appear on the
display of your radio showing that the Aux2Car adaptor is ready to use.
Switch to the Aux2Car adaptor by pressing the CD/ Mode button on the radio.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
Ford (Ford, Lincoln, Mercury)
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
if you use PXHFD1, PXHFD2 make sure that you connect the Black wire to ground and the
Yellow wire to constant 12V+. *If you don’t know the location of constant 12V+, please use a
Volt meter, or consult a Ford dealership.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
1
2
3
4
5
6
7
8
SETTINGS FOR FORD
FOCUS & COUGAR
on
on
off
off
off
off
off
on
SETTINGS FOR ALL
OTHERS
1
2
3
4
5
6
7
8
off
on
off
off
off
off
off
on
See the next page for a full list of vehicles as well as plug location in each.
OPERATION
Switch to the Aux2Car adaptor by pressing the “CD” button on the radio.
If you would like to connect Aux2Car adaptor to 2004 - Town Car,
Grand Marquis, Marauder, LS and Ford Crown Victoria, please see
Ford appendix, page 19.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
Year(s)
IPOD Location and Notes
Model
Year(s)
IPOD Location and notes
Ford
Lincoln
Aviator
2002-2004
1995-1997
PXHFD3 connector behind Radio.
PXHFD2 connector behind Radio.
Premium Audio System
PXHFD2 connector behind
Radio.
Crown
Victoria
1995-1997
Premium Audio System
Continental
PXHFD1 (Rear Control Unit) in
the trunk.
PXHFD1 (Rear Control Unit) in the trunk
JBL / Luxury System
Crown
Victoria
1995-1997
1998-2003
JBL / Luxury System
Continental
Continental
LS
1995-1997
1998-2004
2000-2003
Crown
Victoria
PXHFD3 connector behind
Radio.
PXHFD3 connector behind Radio.
PXHFD3 connector behind Radio.
PXHFD2 connector behind Radio.
Premium Audio System
Escape
2001-2004
PXHFD3 connector behind
Radio.
PXHFD2 connector behind
Radio.
Mark VIII
1995-1998
PXHFD2 connector behind Radio.
Premium Audio System
Econoline
Econoline
Escort
1997
Premium Audio System
Navigator
Navigator
1997-1998
1999-2004
1998-2004
1997-2004
PXHFD3connector behind Radio.
PXHFD3 connector behind Radio.
PXHFD2 connector behind Radio.
Premium Audio System
PXHFD2 connector behind
Radio.
Excursion
2000-2004
PXHFD3 connector behind
Radio.
Town Car
1995-1997
PXHFD1 (Rear Control Unit) in the trunk.
JBL / Luxury System
PXHFD2 connector behind
Radio.
Town Car
Town Car
1995-1997
1998-2003
Expedition
Expedition
1997-1998
1999-2004
Premium Audio System
PXHFD3 connector behind Radio.
PXHFD3 connector behind
Radio.
Mercury
Cougar
PXHFD2 connector behind
Radio.
PXHFD4 connector behind Radio.
6 Disc IPOD only
1999-2004
1995-1997
Explorer
1995-1997
Premium Audio System
PXHFD2 connector behind Radio.
Premium Audio System
PXHFD1 (Rear Control Unit) in
the trunk.
Grand Marquis
Explorer
Explorer
1995-1997
1998-2004
JBL / Luxury System
PXHFD1 (Rear Control Unit) in the trunk.
JBL / Luxury System
PXHFD3 connector behind
Radio.
Grand Marquis
Grand Marquis
Mountaineer
1995-1997
1998-2003
1997
PXHFD3 connector behind Radio.
PXHFD2 connector behind
Radio.
PXHFD1 (Rear Control Unit) in rear pas-
senger side panel.
F-150
Pick-Up
1997
Premium Audio System
PXHFD2 connector behind Radio.
Premium Audio System
F-Series
Pick-Up
1998-2004
PXHFD3 connector behind
Radio.
Mountaineer
Mountaineer
Sable
1997
PXHFD4 connector behind
Radio.
1998-2004
1996-2005
PXHFD3 connector behind Radio.
Focus
2000-2003
6 Disc IPOD only
PXHFD1 (Rear Control Unit) in
trunk/rear.
PXHFD2 connector behind
Radio.
Tracer
1997-2004
PXHFD2 connector behind Radio.
PXHFD2 connector behind Radio.
Premium Audio System
HN80 Heavy
Truck
1996-1997
2001-2004
Premium Audio System
Mustang
PXHFD3 connector behind
Radio.
Villager
Villager
1997-1998
1999-2002
PXHFD3 connector behind Radio.
PXHFD2 connector behind
Radio.
Ranger
1995-1997
1998-2004
2000-2004
Premium Audio System
Ranger
PXHFD3connector behind Radio.
Sport Trac
PXHFD3 connector behind
Radio.
Taurus
1996-2005
2000-2004
PXHFD1 (Rear Control Unit) in
the trunk.
Thunderbird
PXHFD3 connector behind
Radio.
Windstar
1999-2004
PXHFD3 connector behind
Radio.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
GM (Buick, Cadillac, Chevy,
GMC, Pontiac, Saturn)
*PLEASE READ*
*1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible with the
Aux2Car ADAPTER.
*2000-2004 Radios with built in CD player ARE compatible.
Separate OEM CD (1995-2000) must be disconnected to use the Aux2Car adaptor.
2003 – 2005: If XM mode is used, the you must not have GM factory original XM tuner
installed. If installed you must unplug it for Aux2Car adaptor to work.
Corvette: Please see GM-Corvette appendix, page # 20
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
GM’s use one of three cables (PXHGM1, PXHGM2,
PXHGM3); use the cable that fits, and follow GM table connection guide
If you use “GM-C” cable, please connect the loose Yellow wire to constant 12V+
GM has 3 protocols, please determine by GM table in this guide, your car’s protocol, and set
the Aux2Car accordingly.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
SETTINGS FOR CLASS 2
OPERATION FOR CLASS 2
1
2
3
4
5
6
7
8
Switch to the Aux2car adaptor by
pressing the “Aux” or “Source”
button.
on
off
on
off
off
off
off
on
SETTINGS FOR XM
OPERATION FOR XM
Switch to the Aux2car adaptor by
pressing the “Band” button, until
you see XM1.
1
2
3
4
5
6
7
8
off
on
on
off
off
off
off
on
The screen will change to D1 T1
( Disc 1, Track 1)
2003 – 2005: If XM mode is used, the you must not have GM factory original XM
ttuner installed. If installed you must unplug it for Aux2Car adaptor to work.
SETTINGS FOR E & C
OPERATION FOR E&C
1
2
3
4
5
6
7
8
Switch to the Aux2Car adap-
tor by pressing the “Aux” or
“Source” button.
off
on
on
off
off
off
off
on
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
Year(s)
IPOD Location and Notes
Chevrolet - continue
Equinox
Notes for Buick:Requires GM factory
CD data cable part # 12344003 if not
pre-wired in trunk.
2005
PXHGM3 Cable
Buick
behind HeadunitPro-
tocol: XM / Class 2
Century
1997-2003
2000- 2002
PXHGM2 Cable in trunk.Protocol: E&C
Impala
2000-2005
1995-1999
1996-1999
1997-2000
2000-2005
1996-1999
2003-2005
1996-2002
2003-2005
1995-2002
2003-2005
1995-2002
2004
PXHGM3 Cable
behind HeadunitPro-
tocol: Class 2
Le Sabre
PXHGM2 Cable in trunk.Protocol:
Class 2
Impala
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
Le Sabre
Park Ave
Rainer
1995-1999
1995-2005
2004
PXHGM2 Cable in trunk.Protocol: E&C
PXHGM2 Cable in trunk.Protocol: E&C
Lumina
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
PXHGM3 cable behind RadioProtocol:
XM / Class 2
Regal
1995-2003
1996-1999
PXHGM2 Cable in trunk.Protocol: E&C
Malibu
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
Riviera
PXHGM2 Cable in trunk.Protocol:
E&C
Monte Carlo
Monte Carlo
Silverado
Silverado
Suburban
Suburban
Tahoe
PXHGM3 Cable
behind HeadunitPro-
tocol: Class 2
Rendezvous
2003-2005
PXHGM3 cable behind RadioProtocol:
XM / Class 2
Roadmaster
Skylark
1995-1996
1996-1998
PXHGM2 Cable in trunk.Protocol: E&C
PXHGM2 Cable in trunk.Protocol: E&C
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
PXHGM3 Cable
behind HeadunitPro-
tocol: Class 2
Cadillac
Catera
2000-2001
PXHGM2 Cable in trunk.Protocol:
Class 2
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
Catera
DeVille
DeVille
1997-1999
1995-1999
2000-2001
PXHGM2 Cable in trunk.Protocol: E&C
PXHGM2 Cable in trunk.Protocol: E&C
PXHGM3 Cable
behind HeadunitPro-
tocol: Class 2
PXHGM2 Cable Behind Glove Comp.
Protocol: E&C
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
DeVille
2001-2005
PXHGM2 Cable Behind Glove Comp.
Protocol: Class 2
Eldorado
Escalade
1995-2002
1999-2002
PXHGM2 Cable in trunk.Protocol: E&C
PXHGM3 Cable
behind HeadunitPro-
tocol: Class 2
PXHGM1 Cable behind HeadunitPro-
tocol: E&C
Tahoe
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
Escalade
Seville
2003-2005
1995-2001
2002-2004
PXHGM3 Cable behind HeadunitPro-
tocol: Class 2
Location: Center Console – PXHGM2
cable; Protocol E&C
Trailblazer
Venture
PXHGM3 Cable
behind HeadunitPro-
tocol: XM / Class 2
Seville
Location: Center Console – PXHGM2
cable; Protocol Class 2
2004-2005
1997-1999
PXHGM3 Cable
behind HeadunitPro-
tocol: XM / Class 2
Chevrolet
Astro Van
1996-2005
2003-2005
2002
PXHGM1 Cable behind HeadunitPro-
tocol: E&C
Venture
PXHGM1 Cable
behind HeadunitPro-
tocol: E&C
Avalanche
Avalanche
Blazer
PXHGM3 Cable behind HeadunitPro-
tocol: Class 2
PXHGM1Cable behind HeadunitPro-
tocol: E&C
1998-2002
1997-2002
PXHGM1 Cable behind HeadunitPro-
tocol: E&C
Camaro
PXHGM1Cable behind HeadunitPro-
tocol: E&C
AM/FM/Cassette with “TAPE/AUX”
button.
Cavalier
Cavalier
Corvette
2003-2005
1996-1999
1997-2004
PXHGM3 Cable behind HeadunitPro-
tocol: XM
PXHGM1 Cable behind HeadunitPro-
tocol: E&C
PXHGM2 Cable in trunk.Protocol:
E&CIf cable not in trunk, please see
Corvette Notes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
Year(s)
IPOD Location and
Notes
GMC
Jimmy
1998-2002
2004
PXHGM1 Cable behind Headunit-
Protocol: E&C
Requires GM factory
data cable Part #
12344003 if not pre-
wired in trunk.
Oldsmobile
Envoy
PXHGM3 Cable behind Headunit-
Protocol: XM / Class 2
Achieva
Alero
1996-1998
1999-2000
2003-2004
PXHGM3 Cable in
trunk.Protocol: E&C
Envoy
1999-2001
1999-2000
1998-2002
1996-2005
1995-2002
2003-2005
1995-2002
1995-2002
PXHGM1 Cable behind Headunit-
Protocol: E&C
PXHGM2 Cable in
trunk.Protocol: E&C
Savana
Sonoma
Safari
PXHGM1 Cable behind Headunit-
Protocol: E&C
Alero
PXHGM3 Cable
behind HeadunitPro-
tocol: XM
PXHGM1 Cable behind Headunit-
Protocol: E&C
PXHGM1 Cable behind Headunit-
Protocol: E&C
Aurora
Aurora
1995-1999
2001-2004
PXHGM2 Cable in
trunk.Protocol: E&C
Sierra
PXHGM1 Cable behind Headunit-
Protocol: E&C
PXHGM2 Cable
in trunk.Protocol:
Class 2
Sierra
PXHGM3 Cable behind Headunit-
Protocol: Class 2
Bravada
Bravada
1997-2001
2004
PXHGM1Cable
behind HeadunitPro-
tocol: E&C
Suburban
PXHGM1 Cable behind Headunit-
Protocol: E&C
PXHGM3Cable be-
hind HeadunitProto-
col: XM / Class 2
Yukon; Yukon-
Denali;Yukon-
XL
PXHGM1 Cable behind Headunit-
Protocol: E&C
Cutlass
1997-1999
1995-1997
1996-1999
1998-2001
1996-1999
1997-1998
2004
PXHGM2 Cable in
trunk.Protocol: E&C
Yukon; Yukon-
Denali;Yukon-
XL
2003-2005
PXHGM3 Cable behind Headunit-
Protocol: Class 2
Cutlass Supreme
Eighty-Eight
Intrigue
PXHGM2Cable in
trunk.Protocol: E&C
Pontiac
PXHGM2Cable in
trunk.Protocol: E&C
Aztek
2003-2005
1996-1999
2000-2005
1996-2002
2003-2005
1996-2000
2004-2005
1999-2000
1996-1999
2003-2005
1996-1998
2004-2005
PXHGM3 Cable behind Headunit-
Protocol: XM / Class 2
PXHGM2Cable in
trunk.Protocol: E&C
Bonneville
Bonneville
Firebird
PXHGM1 Cable behind Headunit-
Protocol: E&C
LSS
PXHGM2Cable in
trunk.Protocol: E&C
PXHGM2 Cable in trunk.Protocol:
Class 2
Regency
Silhouette
PXHGM2Cable in
trunk.Protocol: E&C
PXHGM1 Cable behind Headunit-
Protocol: E&C
PXHGM3 Cable
behind HeadunitPro-
tocol: XM
Grand Am
Grand Am
Montana
Montana
Sunfire
PXHGM3 Cable behind Headunit-
Protocol: XM /Class 2
PXHGM1 Cable behind Headunit-
Protocol: E&C
Silhouette
1996-1999
PXHGM1 Cable be-
hind HeadunitProto-
col: E&CRadio must
be AM/FM/CASS.
PXHGM3 Cable behind Headunit-
Protocol: XM / Class 2
PXHGM1 Cable behind Headunit-
Protocol: E&C
PXHGM1 Cable behind Headunit-
Protocol: E&C
Sunfire
PXHGM3 Cable behind Headunit-
Protocol: XM
TransSport
Vibe
PXHGM1 Cable behind Headunit-
Protocol: E&C
PXHGM3 Cable behind Headunit-
Protocol: XM / Class 2
Saturn
All Models
1995-1999
PXHGM2 Cable in trunk.Protocol:
E&C
2. If not prewired, you must use
two Saturn cables:
GM Part# 21023550 & 21023253
10
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
Chrysler (Chrysler, Jeep, Dodge, Plym-
outh, Eagle)
Make sure the Aux2Car adaptor is compatible with your vehicle, Check for “Disc ^” printed on
preset button “1”. If you see it, it means that your radio can control the Aux2Car adaptor.
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
Remove the radio to see which cable fits your vehicle, and then refer to settings below.
Do not force cables in.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
SETTINGS FOR
“CHRYSLER OLD
DIN” CABLE
1
2
3
4
5
6
7
8
on
off
off
on
off
off
off
on
Use the PXHCH1 cable with vehicles 1995-1999/2000.
-Connects behind the radio
SETTINGS FOR
“CHRYSLER NEW
DIN” AND “10 PIN
CABLES
1
2
3
4
5
6
7
8
off
off
off
on
off
off
off
on
Use the PXHCH2 cable with vehicles 1999-2001.
Use the PXHCH3cable with vehicles 2002-2004.
-Connects behind the radio
Switch to the Aux2Car adaptor by pressing the “CD” or
“MODE” button.
OPERATION FOR
ALL
11
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
Honda – All Honda except Passport
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
1
2
3
4
5
6
7
8
SETTINGS FOR
HONDA
off
off
off
on
off
off
off
on
Compatible with Honda 1992- 2004 except:
Honda Passport
2003-2004 Accord ; 2003-2004 Element ; 2004 +
Honda S2000
Honda uses 2 cables:
1992- 1997 – PXHCH2 cable
1998-2004 – PXHHD1 cable
Connects behind the radio
Switch to the Aux2car adaptor by pressing the “CD” button.
OPERATION
12
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INSTALLATION
Toyota / Scion / Isuzu / Honda-Passport
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
1
2
3
4
5
6
7
8
SETTINGS FOR
TOYOTA
on
on
off
on
off
off
off
on
Toyota 1998 – 2005 – Connects behind the radio with
PXHTY1
2003 and newer :4Runner; Sequoia; Rav4; Prius;
Sienna; Tundra; Tacoma; Highlander Must use Toyota
cable adapter, part # 08695-00370
Isuzu 1998-2003 – Connects behind the radio with
PXHTY1
Scion 2003-2005 – Connects behind the radio ( Must
use Toyota cable adapter, part #08695-00370)
Toyota Matrix uses the PXHGM3 cable with GM class
2 settings. Please see GM section.
Cars that need cable part #08695-00370, can only be
purchased from Toyota dealerships.
Call your nearest Toyota dealership, and ask for the
parts dept.
OPERATION
Switch to the Aux2Car adaptor by pressing the “CD” button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Volkswagen
Make sure you have your radio’s theft protection code before you attempt installation.
When you reconnect power to the battery, you will need to enter this code. Information
about the theft protection code can be found in your vehicle’s audio operation manual.
Before connecting any cables to the Aux2Car you must set the dip switches to the
correct position. If you set the dip-switches after you have connected cables to the
interface, you must disconnect and reconnect them for the Aux2Car to operate.
DIP SWITCHES MUST BE SET BEFORE YOU PLUG IN THE Aux2Car !!!
SETTINGS FOR
ALL VW’S
1
2
3
4
5
6
7
8
on
off
off
off
off
off
off
on
There are two different cables for Volkswagen vehicles. The
PXHVW1 cable is for pre-wired vehicles with the CD Changer
connection in the trunk. The PXHVW2 is for direct connection
behind the radio.
If you use the PXHVW2 cable make sure you connect the black and white cable to ground
If Aux2Car is not being recognized, sound is noisy and/or
Keys on radio not properly working please Disconnect the
Aux2car adapter from trunk, and plug to radio using VW
front cable directly to radio
Cause: VW prewired cable to trunk not shielded and is
causing noise from Aux2Car datalines, into audio lines
OPERATION
Switch to the Aux2Car adaptor by pressing the “CD” button on
the radio.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
CHAPTER
3
Symptom
No Power
Cause
Remedy
Blown fuse
Replace fuse with same
amp. Rating. If the fuse
blows again, call tech
support.
No Power
Bad connection
Check cable connection.
Alternator noise is heard
(Changes with gas)
Wrong wiring creates
ground loop.
Call tech support or ask a
local car audio shop.
Radio can’t recognize
Aux2car adaptor
Bad cables or cables are
not connected properly
between converter box and
car radio
Check connection and
cables, push in firmly.
Aux2car adaptor suddenly is Bad connection or loss of
Unplug the black converter
box from Radio and plug
again
not recognized any more
power to interface
Radio can’t recognize
Aux2car adaptor
Wrong selection on dip
switch in the converter box
Select the right protocol for
you car. (See Page 3)
For technical support call 800-477-2267 9:30 am-6pm EST. MON - FRI
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Warning
One Year Limited Warranty
The quality controls used in the manufacture of this product will ensure your satisfaction.
This warranty applies only to the original purchaser of this product from an authorized
dealer.
This warranty covers any supplied or manufactured parts of this product that, upon inspec-
tion by Peripheral Electronics authorized personnel, is found to have failed in normal use
due to defects in material or workmanship. This warranty does not apply to installation
expenses.
Attempting to service or modify this unit, operating this unit under conditions other than
those recommended or voltages other than the voltage indicated on this unit, will render
this WARRANTY VOID.
Unless otherwise prescribed by law, Peripheral Electronics shall not be liable for any per-
sonal injury, property damage and or any incidental or consequential damages of any kind
(including water damage) resulting from malfunctions, defects, misuse, improper installation
or alteration of this product.
All parts of this Peripheral Electronics product are guaranteed for a period of 1 year as
follows:
Within the first 12 months from date of purchase, subject to the conditions above, Peripher-
al Electronics will repair or replace the product at their discretion, if it is defective in material
or workmanship providing it is returned to an Authorized Peripheral Electronics Dealer, with
PROOF OF PURCHASE from an authorized dealer.
Warning:
This equipment may be reset by unintentional electrostatic discharge during operation.
Exposure to direct sunlight or extreme heat may cause damage or malfunction.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
1. Use of headphones while operating an automobile or moving vehicle is not recommend-
ed and is unlawful in some countries and areas.
2. Be careful and attentive on the road. Stop operation of the Aux2Car adaptor if you find it
disruptive or distracting while driving. The driver of a motor vehicle should not operate the
Aux2Car ADAPTER while driving.
FCC Class B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encourages to try to correct
the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio/television technician for help.
Notice 1: The changes or modifications not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
Notice 2: Shielded interface cables, if any, must be used in order to comply with the emis-
sion limits.
Copyrights, warnings, and other information.
The illustrations, technical information, data and descriptions contained in this publication
are subject to change without notice.
This publication, together with all information contained in it, and all intellectual property
rights on this publication remain the property of Peripheral Electronics. The user may not
pass this publication on to third parties.
No liability will be accepted for any inaccuracies or omissions in this publication, although
due care has been taken to make it as complete and accurate as possible
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FORD Appendix
Aux2Car Adaptor Connection
2004 - Town Car, Grand Marquis, Marauder,
1. Preparing the Ford-12pin Cable
Take the PXHFD4 cable and cut off the black 12-pin plug. You will use only the cable and
big White 22 pin connector (connects to the iPod2car).
2. Connection to the Vehicle
There are two connectors located behind the radio, a 16 pin connector and a 24 pin con-
nector.
We will first work with the 16 pin connector.
16pin Connector:
Red to 16pin connectors Orange/Black cable (Pin #9)
Blue to 16pin connectors Gray cable (Pin #10)
Green to 16pin connectors Light Green/Red cable (Pin #1)
Pink to 16pin connectors Violet cable (Pin #2)
Yellow to 16pin connectors Light Blue/Pink cable (Pin #7)
White to 16pin connectors Tan cable (Pin #8)
Brown to 16pin connectors Light Green/Black cable (Pin #6)
24pin Connector:
Gray to 24pin connectors Violet/Light Blue cable (Pin #1)
Orange to 24pin connectors Black/Light Green cable (Pin #24)
*Important Note:
Some vehicle production runs do not have a cable plugged into the 16pin pin connector
on the back of the headunit. If you are installing in this type of vehicle you can use another
cable (For example the Honda cable) and shave the plastic off of the white 22pin connector
and remove the pins inside. These pins can then be inserted into the holes on the back of
the vehicles stereo. Call technical support if you need further assistance with this option.
3. Technical Support
If you have any questions or need any support, please feel free to call 800-477-2267 from
9:30am-6pm EST.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
GM Appendix 1
Corvette
Aux2car Adaptor Connection to
Chevrolet Corvette
Most Corvettes are pre-wired to the trunk. In case you can’t find the connector in the
trunk, please do the following:
1. Preparing the GM-A Cable
Take the PXHGM1 cable and cut off the Black and Red plug. You will then have two cables
in your hands. One cable with the big white 22 pin connector and 1 with a small white 9 pin
connector. You will use only the cable with the big White 22 pin connector (connects to the
Aux2Car).
2. Connection to the Vehicle
There are two connectors located behind the radio, one is black and the other is grey. We
will first work with the grey connector.
Grey Connector:
Blue to Connector Brown+White (Pin 11, the 1st pin)
Red to Connector Green+White (Pin 12, the 2nd pin)
Black to Connector Black+White (Pin 13, the 3rd pin)
Yellow to Connector Dark Green (Pin 15, pin 14 is empty)*
Black Connector:
Orange to Black Connector thick Orange (Pin 10, the last pin, +12v)
Brown to Black Connector Black+White (Pin 5, the middle, Ground)
3. Technical Support
If you have any questions or need any support, please feel free to call 800-477-2267 from
9:30am-6pm EST.
NOTE: CORVETTE 2005 IS NOT COMPATIBLE
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Cadillac; Oldsmobile; Buick that
use E&C protocol (1995 – 1999 )
- Cable in trunk can’t be found
Most 1995 – 1999 Cadillac’s, Oldsmobile’s & Buick’s are pre-wired to the trunk. In
case you can’t find the connector in the trunk, please do the following:
1. Preparing the PXHGM1 Cable
Take the PXHGM1 cable and cut off the Black and Red plug, you will then have two cables
in your hands. One cable with the big white 22 pin connector and 1 with a small white 9 pin
connector. You will use only the cable with the big White 22 pin connector (connects to the
Aux2Car).
2. Connection to the 32 pin connector behind the Radio
Yellow to 32 pin connector, Pin # 1 DK Green cable ( Data )
* Black to 32 pin connector, Pin # E9 Black +White cable (Audio GND)
* Blue to 32 pin connector, Pin # E10 Brown +White cable (Left Audio)
* Red to 32 pin connector, Pin # E11 DK Green +White cable (Right Audio)
Orange to 32 pin connector, Pin # F1 Orange cable ( 12V+ )
Brown to 32 pin connector, Pin # E16 Black + White cable (Ground)
3. Technical Support
If you have any questions or need any support, please feel free to call 800-477-2267 from
9:30am-6pm EST.
*Some cars don’t have the Brown /White cable to Pin # E10, the Dark Green/White cable to pin #E11 and the Black /White
cable to pin #E9.
In such case, please use from any other cable ( i.e. Ford cable) from the 22pin White connector, the female pin.
Just remove from the white 22 connector a Female pin and use it to connect to GM radio missing pin. It fits perfectly. To
remove pin from 22 pin connector, you can shave of the plastic with a knife until you reach the pin.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Please check out our other products including:
factory radios
NeoChanger
Complete universal CD changer that connects to
most factory stereos
Peripheral Electronics®,
a division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
727-572-9255 or [email protected]
©2005 AAMP™ of Florida, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|