Model No. NTB39020
Serial No.
USER’S MANUAL
Write the serial number in the
space above for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight rack.
1. Read all instructions in this manual before
using the weight rack. Use the weight rack
only as described in this manual.
10. Always set both weight rests at the same
height.
11. The weight rack is designed to support a
maximum of 310 pounds, including the bar-
bell, on the weight rest arms. Do not place
more than 150 pounds on the weight car-
riage. Note: The weight rack is designed to
be used with an Olympic barbell. The weight
rack does not include a barbell or weights.
2. It is the responsibility of the owner to ensure
that all users of the weight rack are ade-
quately informed of all precautions.
3. The weight rack is intended for home use
only. Do not use the weight rack in any com-
mercial, rental, or institutional setting.
12. Always place an equal amount of weight on
each side of the weight carriage or barbell.
4. Use the weight rack only on a level surface.
Cover the floor beneath the weight rack to
protect the floor.
13. Always secure the weights with the weight
clips when they are mounted on the weight
carriage.
5. Make sure all parts are properly tightened
each time you use the weight rack. Replace
any worn parts immediately.
14. Always exercise with a partner. Your partner
should be ready to catch the barbell if you
cannot complete a repetition.
6. Keep children under 12 and pets away from
the weight rack at all times.
15. Always disconnect the barbell from the Long
Cable when performing an exercise that does
not require it. The barbell could be lifted off
the weight rest arms and fall.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
16. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
9. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile NordicTrack®
toll-free at 1-888-825-2588, Monday through Friday,
STRENGTH SPOTTER RACK weight rack. The weight 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
rack offers a selection of weight stations designed to
develop every major muscle group of the body.
Whether your goal is to tone your body, build dramatic
muscle size and strength, or improve your cardiovas-
cular system, the weight rack will help you to achieve
the specific results you want.
To help us assist you, please note the product model
number and serial number before calling. The model
number is NTB39020. The serial number can be found
on a decal attached to the weight rack (see the front
cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight rack. If you have additional ques-
tions, please call our Customer Service Department
Swivel Arm
Pull-up Bar
Safety Spotter
Weight Rest
Left Side
Upright
Right Side
Weight Carriage
Foot Plate
Low Pulley
Station
ASSEMBLED
DIMENSIONS:
Height: 85 in.
Width: 66 in.
Depth: 68 in.
Note: The terms “right side” and
“left side” are determined relative to
a person facing away from the rack;
they do not correspond to right and
left on the drawings in the manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• As you assemble the weight rack, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight rack can be assembled success-
fully by anyone. However, it is important to real-
ize that the versatile weight rack has many parts
and that the assembly process will take time.
Most people find that by setting aside plenty of
time, assembly will go smoothly.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The included Allen wrenches and the following
tools (not included) are required for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• One Phillips screwdriver
• Assembly requires two people.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1.
1
Before beginning assembly, make sure you
understand the information in the box
above.
52
1
Attach the Foot Plate (17) to the Base Frame (1)
with two M10 x 70mm Button Head Bolts (52),
two M10 Washers (62), and two M10 Nylon
Locknuts (64).
62
64
52
62
64
17
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press a 50mm x 100mm Cap (23) into the Right
Frame (3). Insert two M10 x 116mm Carriage
Bolts (53) up into the Right Frame. Note: The
Right Frame has a short weldment in the indi-
cated location; the other side has a long weld-
ment.
2
High
Side
Attach the Right Frame (3) to the Base Frame (1)
with two M10 x 70mm Button Head Bolts (52),
two M10 Washers (62), and two M10 Nylon
Locknuts (64). Do not tighten the Locknuts yet.
Numbers
Attach the Left Frame (not shown) to the Base
Frame (1) in the same manner.
4
Orient an Upright (4) as shown. Attach the
Upright to the Right Frame (3) with the two M10 x
116mm Carriage Bolts (53) and two M10 Nylon
Locknuts (64). Do not tighten the Locknuts yet.
64
62
64
23
52
Attach the other Upright (not shown) to the
Left Frame (not shown) in the same manner.
3
1
52
53
Short
Weldment
3. Make sure there is a 60mm Square Cap (22) in
the top of the Center Upright (6).
3
Orient the Center Upright (6) so that the letters
are on the indicated side. Attach the Center
Upright to the Base Frame (1) with two M10 x
152mm Button Head Bolts (54), two M10
22
Washers (62), and an M10 Nylon Locknut (64).
Make sure the Washers and Locknut are on
the lower Bolt. Do not tighten the Locknut yet.
Letters on
this side
6
1
64
62
62
54
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Slide two Weight Stops (28) onto the Weight
Carriage (11). Press two Carriage Endcaps (27)
into the ends of the weight tube on the Weight
Carriage.
4
28
27
Weight
Tube
Slide the Carriage Stop (24) onto the Center
Upright (6). Slide the Weight Carriage (11) onto
the Center Upright, with the weight tube on the
side opposite the letters.
28
11
24
27
6
Letters
5. Turn the Knob (32) counterclockwise. Pull the
Knob out as far as it will go and slide the Safety
Spotter (12) onto the Center Upright (6) so that
the hole is on the same side as the letters.
Engage the Knob into an adjustment hole in the
Upright.
5
12
Hole
32
6
Adjustment
Hole
Letters
6. Attach the Center Top Frame (9) to the Center
Upright (6) with two M10 x 152mm Button Head
Bolts (54), four M10 Washers (62), and two M10
Nylon Locknuts (64). Do not tighten the
Locknuts yet.
6
7. Locate the Long Cable (43), which is inserted
through the Left and Right Top Frames (7, 8).
Make sure that the Cable is free of any ties.
During this step, make sure the Cable hangs
behind the Center Upright (not shown).
9
64
62
Have a second person pull on the Long Cable
(43) at both ends of the Right Top Frame (8),
so that it is in the center of the Frame. Attach
the Right Top Frame to the right Upright (4) with
two M10 x 118mm Button Head Bolts (67), two
M10 Washers (62), and two M10 Nylon Locknuts
(64). Do not tighten the Locknuts yet.
54
6
62
7
64
62
67
62
Attach the Right Top Frame (8) to the Center Top
Frame (9) with two M10 x 70mm Button Head
Bolts (52), two M10 Washers (62), and two M10
Nylon Locknuts (64). Do not tighten the
Locknuts yet.
8
Make sure that when the Long Cable (43) is
tight, it is centered in the Right Top Frame (8)
and does not touch any of the Bolts used in
this step. Repeat this step with the Left Top
Frame (not shown).
64
52
9
64
43
4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Attach the Pull-up Bar (10) to the Right Top
Frame (8) with two M10 x 70mm Button Head
Bolts (52), two M10 Washers (62), and two M10
Nylon Locknuts (64). Do not tighten the
Locknuts yet.
8
64
62
8
Repeat this step with the Left Top Frame (not
shown).
10
Tighten the M10 Nylon Locknuts (64) used in
steps 2–8.
52
9. Locate the Medium Cable (45), which has an
eyelet on each end. Attach the Cable inside the
Center Top Frame (9) with an M10 x 165mm
Button Head Bolt (5) and an M10 Nylon Locknut
(64).
9
9
64
5
45
10. Wrap the Medium Cable (45) under a 3 1/2”
Pulley (34). Attach the Pulley and a Cable Trap
(36) between the second set of holes from the top
of the pair of Pulley Plates (33) with an M10 x
50mm Button Head Bolt (57) and an M10 Nylon
Locknut (64). Make sure the Cable Trap is ori-
ented to hold the Cable in the groove of the
Pulley.
10
45
34
64
57
33
36
33
11. Wrap the Medium Cable (45) over a 3 1/2” Pulley
(34), as shown. Attach the Pulley inside the
Center Top Frame (9) with an M10 x 165mm
Button Head Bolt (5) and an M10 Nylon Locknut
(64).
11
34
45
9
64
5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Wrap the Medium Cable (45) over another 3 1/2”
Pulley (34). Attach the Pulley inside the Center
Top Frame (9) with an M10 x 165mm Button
Head Bolt (5) and an M10 Nylon Locknut (64).
12
34
45
64
9
5
13. Attach the end of the Medium Cable (45) to the
Weight Carriage (11) with an M10 x 22mm Button
Head Bolt (59) and an M10 Nylon Locknut (64).
13
45
59
11
64
14. Locate the Short Cable (44). Route the Cable
through the bracket on the Base Frame (1) and
the hole in the Center Upright (6).
14
6
34
64
Attach a 3 1/2” Pulley (34) inside the bracket on
the Base Frame (1), over the Short Cable (44),
with an M10 x 50mm Button Head Bolt (57) and
an M10 Nylon Locknut (64).
1
44
57
15. Note: For clarity, the Foot Plate (17) is not
15
shown in the following steps.
34
44
Remove the upper M10 x 152mm Button Head
Bolt (54) used in step 3.
62
64
51
Wrap the Short Cable (44) over a 3 1/2” Pulley
(34). Attach the Pulley inside the Center Upright
(6) with the M10 x 152mm Button Head Bolt (54),
two M10 Washers (62), two Long Spacers (51),
and an M10 Nylon Locknut (64).
1
51
62
54
9
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Wrap the Short Cable (44) under a 3 1/2” Pulley
(34). Attach the Pulley inside the Base Frame (1)
with an M10 x 165mm Button Head Bolt (5) and
an M10 Nylon Locknut (64).
16
17
18
34
64
1
44
5
17. Wrap the Short Cable (44) under a 3 1/2” Pulley
(34). Attach the Pulley inside the Base Frame (1)
with an M10 x 165mm Button Head Bolt (5) and
an M10 Nylon Locknut (64). Make sure the
Cable is between the Pulley and the welded
rod inside the Base Frame.
34
44
64
Welded
Rod
5
1
18. Wrap the Short Cable (44) over a 3 1/2” Pulley
(34). Attach the Pulley and a Cable Trap (36)
between the second set of holes from the bottom
of the pair of Pulley Plates (33) with an M10 x
50mm Button Head Bolt (57) and an M10 Nylon
Locknut (64). Make sure the Cable Trap is ori-
ented to hold the Cable in the groove of the
Pulley.
64
33
57
36
34
44
19. Wrap the Short Cable (44) under a 3 1/2” Pulley
(34). Attach the Pulley inside the Base Frame (1)
with an M10 x 165mm Button Head Bolt (5) and
an M10 Nylon Locknut (64).
19
44
1
34
64
5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Thread an M6 Nut (71) onto the Short Cable (44).
Attach the end of the Short Cable to the “U”-
bracket (37) with an M6 Washer (63) and an M6
Nylon Locknut (66).
20
43
34
66
63
43
66
Wrap the Long Cable (43) under a 3 1/2” Pulley
(34). Attach the Pulley inside the “U”-bracket (37)
with an M10 x 50mm Button Head Bolt (57) and
an M10 Nylon Locknut (64).
37
64
57
44
See the inset drawing. The M6 Nylon Locknut
(66) should be threaded onto the Short Cable
(44) so that the end of the Short Cable is nearly
touching the Long Cable (43).
44
21. Wrap the Long Cable (43) around a 3 1/2” Pulley
(34). Attach the Pulley and a Cable Trap (36) to
the Center Top Frame (9) with an M10 x 47mm
Button Head Bolt (60), an M10 Washer (62), and
an M10 Nylon Locknut (64). Make sure the
Cable Trap is oriented to hold the Cable in the
groove of the Pulley.
21
60
43
34
36
9
62
64
22. Wrap the Long Cable (43) around a 3 1/2” Pulley
(34). Attach the Pulley and a Cable Trap (36) to
the Center Top Frame (9) with an M10 x 47mm
Button Head Bolt (60) and an M10 Nylon Locknut
(64). Make sure the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
22
36
43
60
34
64
9
23. Wrap the Long Cable (43) over a 3 1/2” Pulley
(34). Attach the Pulley and a Cable Trap (36) to
the Center Top Frame (9) with an M10 x 47mm
Button Head Bolt (60) and an M10 Nylon Locknut
(64). Make sure the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
23
9
36
60
34
64
43
11
Download from Www.Somanuals.com. All Manuals Search And Download.
24. Wrap the Long Cable (43) around a 3 1/2” Pulley
(34). Attach the Pulley and a Cable Trap (36) to
the Center Top Frame (9) with an M10 x 47mm
Button Head Bolt (60), an M10 Washer (62), and
an M10 Nylon Locknut (64). Make sure that the
Cable Trap is oriented to hold the Cable in the
groove of the Pulley and that the Cable Trap
does not contact the Cable.
24
36
34
60
9
43
62
64
25. Attach the Right Support (14) to a Weight Rest
Arm (13) with two M10 x 25mm Screws (56).
25
Rest the Weight Rest Arm (13) on the right
Upright (4).
Repeat this step with the other Weight Rest
Arm (13) and the Left Support (not shown).
4
13
14
56
26. Make sure all parts of the weight rack are properly tightened. In addition, pull each cable a few times
to make sure the cables move smoothly over the pulleys. If the cables do not move smoothly, locate
and correct the problem. When weights are used, the cables may be damaged if they are incorrectly
routed. Refer to the CABLE DIAGRAMS on page 15 for correct cable routing.
The use of all remaining parts will be explained in ADJUSTMENTS, beginning on the following page.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
This section explains how to adjust the weight rack. Refer to the accompanying exercise guide to see the correct
form for each exercise.
Make sure all parts are properly tightened each time the weight rack is used. Replace any worn parts immediately.
The weight rack can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE WEIGHT RESTS AND
SAFETY SPOTTER
A
Hook
Selector
Before performing an exercise that uses a barbell (not
included), adjust the Weight Rest Arms (13) and the
Rod
Safety Spotter (12) to the height that is best suited for
that exercise.
13
See drawing A. The Weight Rest Arms (13) should
be set at a comfortable height for lifting and replacing
the barbell. Engage the hook on each Arm onto a
selector rod on the Upright (4). Make sure the Arms
are set at the same height.
4
See drawing B. Set the Safety Spotter (12) to the
position that will stop the barbell at the lowest point
that you want it to go during the exercise. First, attach
the barbell to the Long Cable (see ATTACHING A
BARBELL TO THE CABLES, below). Then, turn the
Knob (32) counterclockwise until it is loose. Pull the
Knob out as far as it will go and move the Safety
Spotter to the desired height. Engage the Knob into
an adjustment hole in the Center Upright (6) and turn
it clockwise until it is tight.
B
12
32
Adjustment
Hole
WARNING:
Always adjust both
Weight Rest Arms (13) to the same height
before exercising.
6
ATTACHING A BARBELL TO THE CABLES
To use a barbell (not included) with the Safety Spotter
(not shown), set the barbell on the Supports (14, 15
[not shown]). Slide a Barbell Ring (42) onto each end
of the barbell and tighten the M6 x 13mm Screws
(21). Attach the ends of the Long Cable (43) to the
Barbell Rings.
43
WARNING:
Use only an Olympic
47
barbell (not included) with the Barbell Rings
(42). Always disconnect the barbell from the
Long Cable (43) when performing an exercise
that does not require it. The barbell could be lift-
ed off the Supports (14, 15) and fall.
Barbell
42
21
14
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WEIGHTS TO THE WEIGHT
CARRIAGE OR BARBELL
Slide the desired amount of weight (not included)
onto the weight tube on the Weight Carriage (11) or
onto a barbell (not included). Secure the weight to the
Weight Carriage with Weight Clips (65).
Weight
11
Barbell
Do not place weights on the Weight Carriage (11)
when performing exercises that use a barbell.
15
WARNING:
Do not place more than
65
150 pounds on the Weight Carriage (11). Do not
place more than 310 pounds, including the bar-
bell, on the Supports (14, 15). Always place the
same amount of weight on each side of the
Weight Carriage or barbell. Always secure the
weights to the Weight Carriage with Weight
Clips (65).
ATTACHING THE ACCESSORIES TO THE CABLES
To use the Curl Bar (38), attach it to the Long Cable
(43) or the Short Cable (not shown) with the Cable
Clip (47).
44
47
The other accessories (not shown) can be attached
to the cables in the same manner. Use the 12”
Extension Strap (not shown) and the Spring Clip (not
shown) between a cable and the accessory when
necessary.
38
WARNING:
Always disconnect the
accessories when performing exercises that do
not require them.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight
rack, can stretch slightly when it is first used. If there is
slack in the cables, tighten them as described below.
33
64
Remove the M10 x 50mm Button Head Bolt (57) and
the M10 Nylon Locknut (64) attaching a 3 1/2” Pulley
(34) and a Cable Trap (36) to the Pulley Plates (33).
Use the Bolt and Nylon Locknut to reattach the Pulley
and Cable Trap to a set of holes closer to the middle of
the Pulley Plates.
33
57
36
34
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE DIAGRAMS
The cable diagrams below show the proper routing of the Long Cable (43), the Short Cable (44), and the
Medium Cable (45). Use the diagram to make sure that the cables have been assembled correctly. If the cables
have not been correctly routed, the weight rack will not function properly and damage may occur. The numbers
show the correct route for each cable. Make sure that the cable traps do not touch or bind the cables.
5
2
3
Long Cable (43)
6
1
7
Medium Cable (60)
3
1
4
4
5
Short Cable (44)
7
2
2
6
1
4
3
5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART IDENTIFICATION CHART AND PART LIST/
EXPLODED DRAWING. SAVE THIS PART IDENTIFICATION CHART
AND PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE.
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
M10 x 25mm Screw (56)
M10 x 47mm Button Head Bolt (60)
M10 x 50mm Button Head Bolt (57)
M10 x 22mm Button Head Bolt (59)
M6 x 13mm Screw (21)
M10 Washer (62)
M6 Washer (63)
M10 Nylon Locknut (64)
M6 Nylon Locknut (66)
M10 x 70mm Button Head Bolt (52)
M10 x 118mm Button Head Bolt (67)
M6 Nut (71)
M10 x 116mm Carriage Bolt (53)
M10 x 152mm Button Head Bolt (54)
M10 x 165mm Button Head Bolt (5)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NTB39020
R0403A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
2
6
1
1
1
1
1
1
1
2
1
1
2
1
2
2
2
2
1
2
1
1
4
2
2
2
1
1
1
2
14
2
6
1
1
Base Frame
Left Frame
Right Frame
Upright
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
#
2
2
1
2
1
1
1
3
3
2
4
4
2
14
4
4
2
4
4
2
1
4
2
32
1
45
2
4
4
8
1
1
1
1
1
1
1
Curl Endcap
Ab Strap
Ankle Strap
Barbell Ring
Long Cable
Short Cable
Medium Cable
Cable Ball
Cable Clip
Handle
M10 x 165mm Button Head Bolt
Center Upright
Left Top Frame
Right Top Frame
Center Top Frame
Pull-up Bar
Weight Carriage
Safety Spotter
Weight Rest Arm
Right Support
Left Support
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Bearing
Short Spacer
Long Spacer
M10 x 70mm Button Head Bolt
M10 x 116mm Carriage Bolt
M10 x 152mm Button Head Bolt
M10 x 54mm Button Head Bolt
M10 x 25mm Screw
M10 x 50mm Button Head Bolt
M10 x 36mm Button Head Bolt
M10 x 22mm Button Head Bolt
M10 x 47mm Button Head Bolt
Snap Ring
M10 Washer
M6 Washer
M10 Nylon Locknut
Weight Clip
M6 Nylon Locknut
M10 x 118mm Button Head Bolt
M4 x 16mm Screw
M5 x 12mm Screw
Spring Clip
M6 Nut
User’s Manual
Exercise Guide
Large Allen Wrench
Small Allen Wrench
Cover
Foot Plate
Swivel Arm
Trunnion
Press Arm Cap
M6 x 13mm Screw
60mm Square Cap
50mm x 100mm Cap
Carriage Stop
12” Extension Strap
Carriage Bushing
Carriage Endcap
Weight Stop
Safety Bumper
Knob Pin
Knob Bushing
Knob
Pulley Plate
3 1/2” Pulley
4” Pulley
Cable Trap
“U”-bracket
#
#
#
Curl Bar
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTB39020
R0403A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
1. The MODEL NUMBER of the product (NTB39020)
2. The NAME of the product (NordicTrack® STRENGTH SPOTTER RACK weight rack)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the
center of this manual)
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack® STRENGTH SPOTTER RACK weight system (“Product”) is warranted to be free of
all defects in material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the product frame for five years after the date of pur-
chase. ICON warrants all other parts for one year after the date of purchase. Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or component, pro-
viding the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at our
option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper
assembly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and
maintain as set out in your User’s Manual (“Manual”).
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as spec-
ified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instruct-
ed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do the
periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them your name
and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for serv-
ice where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return
Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original shipping car-
ton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the product or prob-
lem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or per-
formance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoy-
ment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the
exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness
for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how
long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights and
you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 193693 R0403A
Printed in China © 2003 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|