Multiquip Portable Generator GA 25H User Manual
OPERATION AND PARTS MANUAL  
MODEL GA-2.5H  
PORTABLE AC GENERATOR  
(HONDA GASOLINE ENGINE)  
S/N 5496762 AND BELOW  
S/N 5496763 AND ABOVE  
Revision #5 (03/04/08)  
To find the latest revision of this  
publication, visit our website at:  
www.multiquip.com  
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
MQ GA-2.5H — AC  
Portable Generator  
Honda GX160K1EMA2  
Gasoline Engine  
Proposition 65 Warning ..............................................2  
Table Of Contents ......................................................4  
Parts Ordering Procedures ........................................5  
Safety Alert Message Symbols .............................. 6-7  
Rules for Safe Operation...................................... 8-10  
Specifications (Generator) .......................................11  
Specifications (Engine) ............................................12  
Dimensions ..............................................................13  
General Information .................................................14  
Load Application ......................................................15  
Controls and Indicators ...................................... 16-17  
Generator Refueling.................................................18  
Installation .......................................................... 19-20  
Pre-Inspection ..........................................................21  
Pre-Inspection (Engine) ...........................................22  
Initial Start-up (Engine) ............................................23  
Initial Start-up (Engine/Operation) ...........................24  
Preparation For Long Term Storage .........................25  
Maintenance....................................................... 26-27  
Wiring Diagram S/N 5496762 & below) ...................28  
Wiring Diagram (S/N 5496763 & above) ..................29  
Troubleshooting (Engine) ................................... 30-31  
Troubleshooting (Generator) ....................................32  
Explanation Of Codes In Remarks Column .............34  
Suggested Spare Parts ............................................35  
Cylinder Head Assembly.................................... 48-49  
Cylinder Barrel Assembly ................................... 50-51  
Crankcase Cover Assembly ............................... 52-53  
Crankshaft Assembly ......................................... 54-55  
Piston Assembly................................................. 56-57  
Camshaft Assembly ........................................... 58-59  
Recoil Starter Assembly..................................... 60-61  
Fan Cover Assembly .......................................... 62-63  
Carburetor Assembly ......................................... 64-65  
Air Cleaner Assembly......................................... 66-67  
Muffler Assembly................................................ 68-69  
Flywheel Assembly ............................................ 70-71  
Ignition Coil Assembly........................................ 72-73  
Governor/Control Assembly ............................... 74-75  
Labels................................................................. 76-77  
Terms and Conditions Of Sale — Parts ...................78  
Generator Component  
Drawings  
Nameplate and Decals....................................... 36-37  
Generator Assembly .......................................... 38-39  
Control Box Assembly (S/N 5496762 & below).. 40-41  
Control Box Assembly (S/N 5496763 & above) . 42-43  
Pipe Frame Assembly (S/N 5496762 & below) .. 44-45  
Pipe Frame Assembly (S/N 5496763 & above).. 46-47  
PAGE 4 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS ORDERING PROCEDURES  
Ordering parts has never been easier!  
Choose from three easy options:  
Effective:  
January 1st, 2006  
Best Deal!  
Order via Internet (Dealers Only)  
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!  
:
If you have an MQ Account, to obtain a  
Username and Password, E-mail us at:  
[email protected].  
■
■
■
View Parts Diagrams  
Order Parts  
PrintSpecificationInformation  
To obtain an MQ Account, contact your  
District Sales Manager for more information.  
Use the internet and qualify for a 5% Discount  
on Standard orders for all orders which include  
complete part numbers.*  
Gotowww.multiquip.comandclickon  
to log in and save!  
Order Parts  
Note: Discounts Are Subject To Change  
Fax your order in and qualify for a 2% Discount  
on Standard orders for all orders which include  
complete part numbers.*  
Order via Fax (Dealers Only)  
:
All customers are welcome to order parts via Fax.  
Domestic (US) Customers dial:  
1-800-6-PARTS-7 (800-672-7877)  
Note: Discounts Are Subject To Change  
Domestic (US) Dealers Call:  
1-800-427-1244  
Order via Phone:  
Non-Dealer Customers:  
International Customers should contact  
their local Multiquip Representatives for  
Parts Ordering information.  
Contact your local Multiquip Dealer for  
parts or call 800-427-1244 for help in  
locating a dealer near you.  
When ordering parts, please supply:  
❒
Specify Preferred Method of Shipment:  
❒
❒
❒
❒
❒
❒
Dealer Account Number  
✓
UPS/Fed Ex  
✓ DHL  
Dealer Name and Address  
■
■
Priority One  
Ground  
✓
Truck  
Shipping Address (if different than billing address)  
Return Fax Number  
Applicable Model Number  
■ Next Day  
■
Second/ThirdDay  
Quantity, Part Number and Description of Each Part  
All orders are treated asStandard Orders  
andwillshipthesamedayifreceivedprior  
to 3PM PST.  
WE ACCEPT ALL MAJOR CREDIT CARDS!  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — SAFETY MESSAGE ALERT SYMBOLS  
HAZARD SYMBOLS  
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!  
Potential hazards associated with the operation of a MQ  
GA-2.5H Portable Generator will be referenced with Hazard  
Symbols which appear throughout this manual, and will be  
referenced in conjunction with Safety Message Alert  
Symbols.  
Safety precautions should be followed  
at all times when operating this  
equipment. Failure to read and  
understand the Safety Messages and  
Operating Instructions could result in  
injury to yourself and others.  
Lethal Exhaust Gas Hazards  
WARNING  
This Owner's Manual has been  
developed to provide complete  
instructions for the safe and efficient  
Engine exhaust gases contain  
poisonous carbon monoxide. This gas  
is colorless and odorless, and can cause  
death if inhaled. NEVER operate this  
equipment in a confined area or  
enclosed structure that does not provide  
ample free flow air.  
operation of the MQ Model GA-2.5H  
Portable Generator. Refer to the  
engine manufacturers instructions for  
data relative to its safe operation.  
Before using this generator, ensure that the operating  
individual has read and understands all instructions in this  
manual.  
Explosive Fuel Hazards  
SAFETY MESSAGE ALERT SYMBOLS  
WARNING  
Gasoline is extremely flammable, and  
its vapors can cause an explosion if  
ignited. DO NOT start the engine near  
spilled fuel or combustible fluids.  
The three (3) Safety Messages shown below will inform you about  
potential hazards that could injure you or others. The Safety  
Messages specifically address the level of exposure to the  
operator, and are preceded by one of three words: DANGER,  
DO NOT fill the fuel tank while the engine is running or  
hot. DO NOT overfill tank, since spilled fuel could ignite if  
it comes into contact with hot engine parts or sparks from  
the ignition system. Store fuel in approved containers, in  
well-ventilated areas and away from sparks and flames.  
DANGER  
You WILL be KILLED or SERIOUSLY INJURED if  
you DO NOT follow these directions.  
Burn Hazards  
WARNING  
WARNING  
Engine components can generate extreme  
heat. To prevent burns, DO NOT touch  
these areas while the engine is running or  
immediately after operations. Never  
operate the engine with heat shields or  
heat guards removed.  
You CAN be KILLED or SERIOUSLY INJURED if  
you DO NOT follow these directions.  
CAUTION  
You CAN be INJURED if you DO NOT follow  
these directions.  
Respiratory Hazards  
WARNING  
ALWAYS wear approved respiratory  
protection when required.  
PAGE 6 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — SAFETY MESSAGE ALERT SYMBOLS  
Equipment Damage  
Rotating Parts Hazards  
CAUTION  
CAUTION  
Hazards  
NEVER operate equipment with covers,  
or guards removed. Keep fingers, hands,  
hair and clothing away from all moving  
parts to prevent injury.  
Other important messages are provided throughout this  
manual to help prevent damage to your portable generator,  
other property, or the surrounding environment.  
Accidental Starting Hazards  
CAUTION  
ALWAYS place the power source, circuit  
breakers or ON/OFF switch in the OFF  
position, when the generator is not in use,  
unless connected to transfer switch.  
Eye and Hearing Hazards  
CAUTION  
ALWAYS wear approved eye and  
hearing protection.  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-3.6H— RULES FOR SAFE OPERATION  
■
NEVER touch the hot exhaust  
manifold, muffler or cylinder. Allow  
these parts to cool before servicing  
engine or generator.  
Read this manual!  
DANGER  
Failure to follow instructions in this manual may lead  
to serious injury or even death! This equipment is to  
be operated by trained and qualified personnel only!  
This equipment is for industrial use only.  
The following safety guidelines should always be used when  
operating the MQ GA-2.5H Portable Generator:  
■
The engine section of this generator requires an adequate  
free flow of cooling air. NEVER operate the generator in  
any enclosed or narrow  
area where free flow of the  
air is restricted. If the air  
GENERAL SAFETY  
■
DO NOT operate or service this  
equipment before reading this entire  
manual.  
flow is restricted it will  
cause serious damage to  
the generator or engine  
and may cause injury to  
people. Remember the  
generator's engine gives  
off DEADLY carbon  
■
■
This equipment should not be operated by persons under  
18 years of age.  
NEVER operate this equipment without proper protective  
clothing, shatterproof glasses, steel-toed boots and other  
protective devices required by the job.  
monoxide gas.  
■
■
ALWAYS refuel in a well-ventilated area, away from sparks  
and open flames.  
■
■
NEVER operate this equipment when not  
feeling well due to fatigue, illness or taking  
medicine.  
ALWAYS use extreme caution when  
working with flammable liquids. When  
refueling, stop the engine and allow it  
to cool. DO NOT smoke around or near  
the machine. Fire or explosion could  
result from fuel vapors, or if fuel is spilled  
on a hot engine.  
NEVER operate this equipment under the influence of  
drugs or alcohol.  
■
NEVER operate the generator in an  
explosive atmosphere or near  
combustible materials. An explosion or  
fire could result causing severe bodily  
harm or even death.  
■
ALWAYS wear proper respiratory (mask),  
hearing and eye protection equipment when  
operating the generator.  
■
■
■
Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
■
NEVER disconnect any "emergency or safety devices".  
These devices are intended for operator safety. Disconnection  
of these devices can cause severe injury, bodily harm or even  
death! Disconnection of any of these devices will void all  
warranties.  
Manufacturer does not assume responsibility for any  
accident due to equipment modifications.  
NEVER use accessories or attachments, which are not  
recommended by Multiquip for this equipment. Damage  
to the equipment and/or injury to user may result.  
PAGE 8 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — RULES FOR SAFE OPERATION  
■
■
■
ALWAYS be sure the operator is familiar with proper safety  
precautions and operation techniques before using generator.  
Maintenance Safety  
■
NEVER lubricate components or attempt service on a  
running machine.  
NEVER leave the generator unattended, turn off engine when  
unattended.  
■
High Temperatures – Always stop engine  
and allow the engine to cool before adding  
fuel, oil or performing service and  
maintenance functions. Contact with hot!  
components can cause serious burns.  
Unauthorized equipment modifications will void all  
warranties.  
■
■
ALWAYS ensure generator is on level ground before use.  
DO NOT place hands or fingers inside generator engine  
compartment when engine is running.  
■
■
Keep the machinery in proper running condition.  
Fix damage to the machine immediately and replace any  
broken parts immediately.  
■
■
NEVER run engine without air cleaner.Severe engine damage  
may occur.  
■
■
ALWAYS replace any worn or damaged warning decals.  
NEVER change or adjust the engine speed which has been  
set at the factory prior to shipping.  
ALWAYS store equipment properly when it is not being used.  
Equipment should be stored in a clean, dry location out of the  
reach of children and un-authorized personnel.  
Power Cord Safety  
■
NEVER let power cables or cords lay in water.  
■
The electrical voltage required to operate the generator can  
cause severe injury or even death through physical contact  
with live circuits. Turn all circuit breakers OFF before  
performing maintenance on the generator.  
■
NEVER stand in water while AC power from the generator  
is being transfer to a load.  
■
■
■
NEVER use a defective or frayed power cable. Check the  
cable for cuts in the insulation.  
■
■
Dispose of hazardous waste properly. Examples of  
potentially hazardous waste are used motor oil, fuel and  
fuel filters.  
NEVER use a extension cord that is frayed or damaged  
where the insulation has been cut.  
DO NOT use food or plastic containers to dispose of  
hazardous waste.  
ALWAYS make certain that proper power or extension cord  
has been selected for the job See Table 3.  
■
■
DO NOT pour waste, oil or fuel directly onto the ground,  
down a drain or into any water source.  
Removing the engine oil drain plug while  
the engine is hot will result in hot oil to gush  
out of the oil drain plug, therefore causing  
severe scalding to any persons in the  
general area of the generator.  
Grounding Safety  
■
ALWAYS make sure that electrical circuits are properly  
grounded per the National Electrical Code (NEC) and  
local codes before operating generator. Severe injury or  
death! by electrocution can result from operating an  
ungrounded generator.  
■
■
ALWAYS make sure generator is properly grounded to a  
suitable earth ground (GROUND ROD). See installation in  
this manual.  
NEVER use gas piping as an electrical ground.  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — RULES FOR SAFE OPERATION  
Emergencies  
DANGER-ELECTROCUTION HAZARDS  
■
ALWAYS know the location of the  
nearest fire extinguisher.  
During operation of this generation, there  
exists the possibility of electrocution,  
electrical shock or burn, which can  
cause severe bodily harm or even  
DEATH!  
■
■
ALWAYS know the location of the nearest  
first aid kit.  
To avoid these hazards:  
NEVER use damaged or worn cables when connecting  
equipment to the generator.Make sure power connecting  
cables are securely connected to the generator’s output  
receptacles, incorrect connections may cause damage  
to the generator and electrical shock.  
In emergencies always know the location of the  
nearest phone or keep a phone on the job site.  
Also know the phone numbers of the nearest  
ambulance, doctor and fire department. This  
information will be invaluable in the case of an  
emergency.  
NEVER grab or touch a live  
power cord with wet hands, the  
possibility exist of electrical  
shock, electrocution, and even  
death!  
NEVER insert any objects into  
the output receptacles during  
operation. This is extremely  
dangerous. ALWAYS turn-off  
the generator and place all circuit breakers in the “OFF”  
position when contact with the output receptacles is  
required. There exist the possibility of electrocution,  
electrical shock or burn, which can cause severe  
bodily harm or even death!  
Backfeed to a utility system can cause  
electrocution and or property damage.  
NEVER connect the generator to a  
building's electrical system without a  
transfer switch or other approved  
device. All installations should be  
performed by a licensed electrician  
in accordance with all applicable laws  
and electrical codes. Failure to do so  
could result in electrical shock or burn  
causing serious injury or even death!  
PAGE 10 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — SPECIFICATIONS (GENERATOR)  
GA-2.5H — OPERATION AND SAFETY DECALS  
Table 1. Specifications (Generator)  
Model  
GA-2.5H  
Type  
Brushless Revolving Field Type  
Excitation  
Solid State, Statically Excited System  
AC Generator  
Speed  
3,600 RPM  
Self-Ventilation  
3.17 gallons (12 liters)  
2.2 kW  
Cooling System  
Fuel Capacity  
Continuous Output  
Stanby Output  
Rated Voltage  
Current Max/Continuous (120V)  
Phase  
2.5 kW  
120V  
60 Cycle AC Power  
Source  
20.8/18.3 amps  
Single Phase (3-wire)  
60 Hz  
Frequency  
Power Factor  
1
20.0 x 16.1 X 18.5 in.  
(510 X 410 X 470 mm)  
Dimensions Approximate  
(L x W x H)  
110 lbs. (50 kg.)  
132 lbs. (60 kg.)  
Dry Net Weight  
Weight (With Fuel)  
Effects of Altitude and Heat  
The maximum output of the engines listed above are applicable to supplying electrical power for continuous service at ambient  
conditions in accordance with SAE Test cord J607. The above ambient conditions are at standard sea level, with a barometric  
reading of 29.92 inches and a temperature of 60 degrees fahrenheit.  
Generally, the engine's output power will decrease 3-1/2% for each 1000 feet of altitude above sea level, and 1% for each 10°  
F Fahrenheit above the standard temperature of 60° F  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — SPECIFICATIONS (ENGINE)  
Table 2. Specifications (Engine)  
Model  
HONDA GX-160K1EMA2  
Air-cooled 4 stroke, Single  
Cylinder, OHV, Horizontal  
Shaft Gasoline Engine  
Type  
2.7 in. x 1.8 in.  
(68 mm x 45 mm)  
Bore X Stroke  
Displacement  
Max Output  
163 cc (9.9 cu-in)  
5.5 H.P./3600 R.P.M.  
Engine/Electric Motor  
Approx. 0.95 U.S. gallons  
(3.6 liters)  
Fuel Tank Capacity  
Unleaded Automobile  
Gasoline  
Fuel  
Lube Oil Capacity  
Speed Control Method  
Starting Method  
0.63 qts. (.60 liters)  
Centrifugal Fly-weight  
Type  
Recoil Start  
12.0 X 14.4 X 13.2 in.  
(304 X 362 X 335 mm)  
Dimension (L x W x H)  
Dry Net Weight  
33.1 lbs. (15 Kg.)  
In keeping with Multiquip's policy of  
constantly improving its products, the  
specifications quoted herein are subject  
to change without prior notice.  
PAGE 12 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — DIMENSIONS  
Figure 1. Dimensions  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — GENERAL INFORMATION  
Excitation System  
WARNING  
Before connecting this generators to any building’s  
electrical system, a licensed electrician must install an  
isolation (transfer) switch.  
The GA-2.5H generator uses a magnet attached to a  
flywheel to produce AC voltage from a lamp coil beneath  
the flywheel. As the magnetic passes the coil it produces  
approximately 19-22 AC volts.  
This voltage (19-22 VAC) is then sent to the control box that  
contains three rectifying diodes:  
Serious injury or death may result without this transfer  
switch.  
z
z
z
Excitation (diode 1)  
Battery (diode 2)  
Slow Down (diode 3)  
GA-2.5H FAMILIARIZATION  
Generator  
The AC voltage will pass through the excitation diode that  
converts the voltage to DC power.  
The Multiquip GA-2.5H generator has been designed as a  
portable dual purpose power source for 60 Hz (single phase)  
lighting facilities, power tools, submersible pumps and other  
industrial and construction machinery.  
This DC power is then sent to the excitation windings housed  
within the main windings commonly called the "stator".  
This voltage is then transferred into the rotor through  
induction.The rotor contains two diodes within it which rectify  
the DC voltage and send it out through the main windings,  
as AC voltage.  
These generators are mounted on rubber vibration isolators  
that have a steel base backplate which is attached to the  
protective steel pipe carrying frame.The protective carrying  
frame is made of steel tubing and fully wraps around the  
generators to protect against damage. See Figures 2A and  
2B for the basic controls and indicators for the GA-2.5H  
generator.  
Alternator  
The alternator, a brushless revolving-field type, is  
permanently aligned to the engine through rigid coupling.  
This portable generator is supplied with a electrical control  
box. To reduce vibration caused by the engine, the control  
box is also placed on rubber isolators.  
Engine  
This generator is powered by a 5.5 HP, air-cooled, 4-stroke  
HONDA gasoline engine. Reference Table 2, for engine  
specifications.  
Control Box  
The control box is provided with the following:  
■
120V twist-lock receptacle, single phase. (S/N 5496763  
and above)  
■
■
120V GFCI single phase duplex output receptacle  
20 amp main circuit breaker  
■
■
AC Voltmeter  
Ground Terminal (S/N 5496762 and below)  
PAGE 14 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — LOAD APPLICATION  
Single Phase Load — 60 Hz  
To determine the running wattage for your load, multiply  
the running wattage as indicated by steps 1, 2, and 3 below:  
Always be sure to check the nameplate on the generators  
and equipment to insure the wattage, amperage and  
frequency requirements are satisfactorily supplied by the  
generators for operating the equipment.  
1. INCANDESCENT LOADS  
Lights, heaters and similar appliances.  
Total the running wattage and multiply by 1.  
Example:  
Generally, the wattage listed on the nameplate of the  
equipment is its rated output. Equipment may require 130—  
150% more wattage than the rating on the nameplate, as  
the wattage is influenced by the efficiency, power factor and  
starting system of the equipment.  
29 light bulbs @ 100W each = 2.9 KW  
use a 3 KW generator.  
2. SMALL MOTORS  
Drills and other small power tools.  
Total the running wattage and multiply by 2.  
Example:  
A 1 inch drill runs at 1 KW  
use a 2 KW generator.  
If wattage is not given on the equipment's  
name plate, approximate wattage may be  
determined by multiplying nameplate  
voltage by the nameplate amperage.  
3. LARGE MOTORS  
Submersible pumps, table saws etc.  
Total the running wattage and multiply by 3.  
Example:  
A conveyor belt runs at 8 KW  
use a 24 KW generator.  
WATTS = VOLTAGE x AMPERAGE  
The power factor of this generators is 1.0 SeeTable 3 below  
when connecting loads.  
Table 3. Power Factor By Load  
CAUTION  
Type Of Load  
Power Factor  
Motors and motor-driven equipment draw much greater  
current for starting than during operation. Always use  
an adequate size extension cable which can carry the  
required load. See Table 4.  
Single-phase induction motors  
0.4 - 0.75  
Electric heaters, incandescent  
lamps  
1.0  
Fluorescent lamps, mecury  
lamps  
0.4 - 0.9  
Extension Cables  
When electric power is to be provided to various tools or  
loads at some distance from the generator, extension cords  
are normally used. Cables should be sized to allow for  
distance in length and amperage so that the voltage  
drop between the generators and point of use (load) is  
held to a minimum. Use the cable selection chart (Table 4 )  
as a guide for selecting proper cable size.  
Electronic devices,  
communication equipment  
1.0  
0.8  
Common power tools  
When using a combination of dual  
receptacles, total load should not  
exceed the rated capacity of the  
generator.  
The idle control device is operated at a  
minimum load capacity of 100W. If the  
load capacity is less than 100W, place  
the idle control switch in the OFF  
position.  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — CONTROLS AND INDICATORS  
Figure 2A. Generator Components  
6. ON-OFF Switch – place engine ON/OFF switch in the  
"ON" position for normal operation. To turn- off the  
generator place switch in the "OFF" position.  
1. 120V Output Receptacle – This NEMA L5- 20R twist-  
lock receptacle will provide 120V, 20 amps, 60 Hz.  
Applies to units with S/N 5496763 and above.  
7. Chassis Ground – This ground connection point should  
be connect to a good earth ground (ground rod). Applies  
to units with S/N 5496763 and above.  
2. GFCI Receptacle – This 5-20R duplex receptacle will  
provide 120V at all times.  
3. AC-Voltmeter – This voltmeter indicates (with a mark)  
the rated 60 Hz, single phase output voltage. In addition  
the voltmeter can also be used as a diagnostic tool. If the  
voltmeter indicator (needle) is below the rated voltage,  
engine problems may exist (low/high RPM's). To prevent  
damage to the generator or power tools turn the generator  
OFF and consult your authorized MQ service dealer.  
This HONDA engine is equipped  
with  
a
low oil shutdown  
capability. A built in sensor will  
automatically turn off the engine  
should the oil level fall below a  
safe operating condition. Make  
sure the generator is placed on  
4. Ciruit Breaker – To protect the generator from an  
overload, a 2- pole 20 amp circuit breaker is provided on  
the control box. Make sure to place the circuit breaker to  
the "OFF" postion prior to starting the engine.  
level ground. Placing the generator on level ground will ensure  
that the low oil sensor will function properly.  
5.  
GFCI Ground – This ground connection point should  
be connect to a good earth ground (ground rod). Applies  
to units with S/N 5496762 and below.  
PAGE 16 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — CONTROLS AND INDICATORS  
Figure 2B. Generator Components  
8. Generator Housing – Contains the rotor, rectifer field 15. Fuel Cock Lever – Turn this lever downward to start  
coil assembly, aramature, bearings and other components  
that make up generator asembly.  
(down)the flow of fuel to the carburetor. Turn upward to  
stop (up) the flow of fuel.  
9. Spark Plug – Provides spark to the ignition system. Set 16. Throttle Lever – Used to adjust engine RPM speed.  
spark plug gap to 0.6 - 0.7 mm (0.024 - 0.028 inch).Clean  
spark plug once a week.  
This unit is set at the factory and is not adjustable.  
17. Recoil Starter (Pull Rope) – Used for manual-starting  
of the engine. Pull the starter grip until resistance is felt,  
then pull briskly and smoothly.  
10. Muffler/Heat Shield – Used to reduce noise and  
emissions. NEVER touch this heat shield when the  
generator is in use. Always allow time for the generator to  
cool down before performing maintenance.  
18. Engine – This generator uses a 5.5 HP HONDA air-  
cooled, 4-stroke , single cylinder, overhead camshaft  
gasoline engine. Engine uses unleaded gasoline.  
11. Oil Dipstick/ Filler Cap– Remove the filler cap dipstick  
when checking the engine oil level.Add engine oil through  
19. Air Cleaner – Every 50 hours: Prevents dirt and other  
debris from entering the fuel system. Remove wing-nut  
on top of air filter cannister to gain access to filter element.  
NEVER run the engine without an air cleaner.  
12. Oil Drain Plug – Remove this plug to drain engine oil  
from the crankcase.  
13. Carburetor Fuel Cup – Inspect the fuel cup weekly for  
water and dirt. Clean as referenced in the maintenance  
section of this manual.  
20. Fuel Gauge – Read this gauge to determine when fuel  
is low.  
14. Choke Lever – Used for starting the engine. Close the  
choke lever when starting a cold engine or in cold weather  
conditions. The choke enriches the fuel mixture. Open  
the choke lever if starting a warm engine or in warm  
weather conditions.  
21. Fuel Gauge/Tank – Remove this cap to add unleaded  
gasoline to the fuel tank.Replenish with clean unleaded  
gasoline. Make sure cap is tightened securely. DO NOT  
over fill. Fuel tank capacity is 3.2 gallons (12 liters).  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — GENERATOR REFUELING  
DANGER  
Adding fuel to the tank should be done only when  
the engine is stopped and has had an  
opportunity to cool down. In the event of a fuel spill, DO NOT  
attempt to start the engine until the fuel residue has been  
completely wiped up, and the area surrounding the engine is  
dry. If generator is placed in a truck bed with a plastic liner,  
REMOVE generator from truck bed and place on ground  
(Figure 3) to refuel. This possibility exist of fire or explosion  
due to static electricity.  
Figure 3. Generator Refueling  
PAGE 18 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — INSTALLATION  
Outdoor Installation  
Indoor Installation  
Install the generator in a area that is free of debris,  
bystanders, and overhead obstructions. Make sure the  
generator is on secure level ground so that it cannot slide or  
shift around. Also install the generator in a manner so that  
the exhaust will not be discharged in the direction of nearby  
homes.  
Exhaust gases from gasoline engines are extremely  
poisonous. Whenever an engine is installed indoors the  
exhaust fumes must be vented to the outside. The engine  
should be installed at least two feet from any outside wall.  
Using an exhaust pipe which is too long or too small can  
cause excessive back pressure which will cause the engine  
to heat excessively and possibly burn the valves.  
Eliminate the danger of deadly carbon monoxide gas.  
Remember that exhaust fumes from any gasoline engine  
are very poisonous if discharged in a closed room, but  
harmless if allowed to mix with the outside air. If the  
generator is installed indoors, you must make provisions  
for venting the engine exhaust to the outside of the building.  
The installation site must be relatively free from moisture  
and dust. All electrical equipment should be protected from  
excessive moisture. Failure to do will result in deterioration  
of the insulation and will result in short circuits and grounding.  
Foreign materials such as dust, sand, lint and abrasive  
materials have a tendency to cause excessive wear to  
engine and alternator parts.  
Generator Grounding  
To guard against electrical shock and possible damage to  
the equipment, it is important to provide a good EARTH  
ground. Always use the ground terminal on the generator  
to ground the generator.  
CAUTION  
Article 250 (Grounding) of the National Electrical Code  
(NEC) provides guide lines for proper grounding and  
specifies that the cable ground shall be connected to the  
grounding system of the building as close to the point of  
cable entry as practical.  
Pay close attention to ventilation when  
operating the generator inside tunnels  
and caves.The engine exhaust contains  
noxious elements.  
NEC articles 250-64(b) and 250-66 set the following  
grounding requirements:  
Mounting  
The generator should always be mounted on a flat level  
surface to isolate vibration of the generator when it is  
running. DO NOT place the generator on slopes, the  
possibility exists that the generator could slide.  
1. Use one of the following wire types to connect the  
generator to earth ground.  
a. Copper - 10 AWG (5.3 mm2) or larger.  
b. Aluminum - 8 AWG (8.4 mm2) or larger.  
2. When grounding the generator (Figure 3) connect the  
ground cable between the lock washer and the nut on  
the generator and tighten the nut fully.Connect the other  
end of the ground cable to earth ground.  
3. NEC article 250-52(c) specifies that the earth ground  
rod should be buried a minimum of 8 ft. into the ground.  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — INSTALLATION  
Connecting the Ground  
The nut and ground terminal on the generator should always be used to connect the generator to a suitable ground. The  
ground cable should be #8 size wire minimum.  
At the generator, connect the terminal of the ground cable between the lock washer and the nut (Figure 4) and tighten the  
nut fully. Connect the other end of the ground cable to a suitable earth ground (ground rod).  
Figure 4. Generator Grounding  
PAGE 20 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — PRE-INSPECTION  
General Inspection Prior to Operation  
Ground Power Tools  
Extension Cable  
When electric power is to be provided to various tools or loads  
at some distance from the generator, extension cords are  
normally used. Cables should be sized to allow for distance in  
length and amperage so that the voltage drop between the  
generator and point of use (load) is held to a minimum. Use  
the cable selection chart (Table 4) as a guide for selecting  
proper cable size.  
When using power tools or electrical equipment requireing AC  
power from the generator, make sure connecting (power tool)  
cable (Figure 5) has a ground as shown in Figure.  
Never! use power tools or  
equipment that do not have a  
ground capability, the possibility  
exists of electrocution, electrical  
shock or burn, which can cause  
severe bodily harm or even  
DEATH!  
Main Circuit Breaker  
To protect the generator from an overload always place the  
main circuit breaker in the "OFF" position prior to starting the  
engine.  
Figure 5. Ground Cables/Plugs  
Table 4. Cable Selection (60 Hz, Single Phase Operation)  
Load In  
Watts  
Maximum Allowable Cable Length  
Current in  
Amperes  
At 120  
Volts  
#10 Wire  
#12 Wire  
#14 Wire  
#16 Wire  
2.5  
5
300  
600  
1000 ft.  
500 ft.  
350 ft.  
250 ft.  
150 ft.  
125 ft.  
600 ft.  
300 ft.  
200 ft.  
150 ft.  
100 ft.  
75 ft.  
375 ft.  
200 ft.  
125 ft.  
100 ft.  
65 ft.  
250 ft.  
125 ft.  
100 ft.  
7.5  
10  
15  
20  
900  
1200  
1800  
2400  
50 ft.  
CAUTION: Equipment damage can result from low voltage.  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — PRE-INSPECTION (ENGINE)  
CAUTION  
NEVER operate the generator in a  
confined area or enclosed area structure  
that does not provide ample free flow of  
air.  
Figure 7. Engine Oil Dipstick (Oil Level)  
Table 5. Oil Type  
ALWAYS wear approved eye and hearing  
protection before operating the generator.  
Before Starting  
Season  
Summer  
Spring/Fall  
Winter  
Temperature  
25°C or Higher  
25°C~10°C  
Oil Type  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
1. Read safety instructions at the  
beginning of manual.  
2. Clean the generator, removing  
dirt and dust, particularly the  
engine cooling air inlet, carburetor  
and air cleaner.  
0°C or Lower  
DANGER EXPLOSIVE FUEL  
3. Check the air filter for dirt and dust. If air filter is dirty,  
replace air filter with a new one as required.  
Motor fuels are highly flammable and can  
be dangerous if mishandled.DO NOT smoke  
while refueling. DO NOT attempt to refuel  
the generator if the engine is hot! , running  
or in the dark.  
4. Check carburetor for external dirt and dust. Clean with  
dry compressed air.  
5. Check fastening nuts and bolts for tightness.  
Engine Oil Check  
1. To check the engine oil level, place the generator on  
secure level ground with the engine stopped.  
Fuel Check  
1. Close the fuel cock before filling the fuel tank.  
2. Remove the fuel cap located on top of fuel tank.  
2. Remove the filler dipstick from the engine oil filler hole  
(Figure 6) and wipe clean.  
3. Read the fuel gauge located on top of the fuel tank (Figure 8)  
to determin if the fuel level is low. If fuel is low, replenish  
with clean unleaded fuel.  
Figure 8. Fuel Gauge  
Figure 6. Engine Oil Dipstick (Removal)  
3. Insert and remove the dipstick without screwing it into the  
filler neck. Check the oil level shown on the dipstick.  
4. When refueling, be sure to use a strainer for filtration. DO  
NOT top-off fuel. DO NOT fill the tank beyond capacity.  
Wipe up any spilled fuel immediately!  
4. If the oil level is low (Figure 7), fill to the edge of the oil filler  
holewiththerecommendedoiltype(Table5).Maximum oil  
capacity is .63 quarts (0.6 liters)  
PAGE 22 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — INITIAL START-UP (ENGINE)  
3. Place the choke lever (Figure 11) in the "OPEN " position  
CAUTION  
if starting a warm engine or the temperature is warm.  
DO NOT attempt to operate this  
generator until the Safety, General  
Information and Inspection sections  
of this manual have been read and  
thoroughly understood.  
4. Place the engine ON/OFF switch (Figure 12) in the "ON  
" position.  
This section is intended to assist the  
operator with the initial start-up of the trash generator. It is  
extremely important that this section be read carefully before  
attempting to use the generator in the field.  
Before Starting the Engine  
Figure 12. Engine ON/OFF Switch (ON)  
1. Be sure to disconnect all electrical loads from the  
generator prior to starting the engine.  
5. Grasp the starter grip (Figure 13) and slowly pull it out.The  
resistance becomes the hardest at a certain position,  
corresponding to the compression point. Pull the starter  
grip briskly and smoothly for starting.  
2. NEVER start the engine with the main circuit breaker  
in the “ON" position. Place the main circuit breaker  
(Figure 9) in the OFF position.  
Figure 9. Main Breaker (OFF Position)  
Starting the Engine  
1. Place the engine fuel valve lever (Figure 10) to the "ON"  
Figure 13. Starter Grip  
position.  
”
CAUTION  
DO NOT pull the starter rope all the way to the end.  
DO NOT release the starter knob after pulling. Allow it  
to rewind as soon as possible.  
Figure 10. Engine Fuel Valve Lever (ON Position)  
2. Place the choke lever (Figure 11) in the "CLOSED "  
position if starting a cold engine.  
Figure 11. Choke Lever  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — INITIAL START-UP ENGINE/OPERATION  
Stopping The Engine  
6. If the engine has started, slowly return the choke lever  
Normal Shutdown  
(Figure 11 ) to the “OPEN” position. If the engine has not  
started repeat steps 1 through 5.  
1. Place the main circuit breaker (Figure 9) in the OFF  
position.  
7. Before the generator is placed into operation, run the  
engine for 3-5 minutes. Check for abnormal smells, fuel  
leaks, and noises that would associate with lose compo-  
nents.  
2. Remove the load from the generator, and let the engine  
run at idle for 3-5 minutes with the idle control switch in  
the ON position (Up)  
8. Refer to the AC voltmeter (Figure 14) on the control  
panel.The voltage indicated on the voltmeter should be  
120 VAC with no load applied.  
3. Place the engine ON/OFF switch (Figure 17) in the "OFF"  
position.  
Figure 17. Engine ON/OFF Switch (OFF)  
Figure 14. AC Voltmeter (120 VAC)  
4. Place the engine fuel valve lever (Figure 18) to the "OFF"  
9. If desired, verify with a voltmeter (Figure15) that 120  
VAC is present at the GFCI duplex receptacle and the  
120V twist-lock receptacle.  
position.  
”
Figure 18. Engine Fuel Valve Lever (OFF Position)  
Emergency Showdown  
1. Place the engine ON/OFF swith (Figure 17) in the  
"OFF" position.  
Figure 15. 120 VAC GFCI Receptacle  
Connecting the Load  
1. Connect the load to the output receptacles.  
2. Place the main circuit breaker (Figure 16) in the ON  
position.  
Figure 16. Main Circuit Breaker (ON)  
PAGE 24 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — PREPARATION FOR LONG -TERM STORAGE  
Generator Storage  
For storage of the generating set for over 30 days, the  
following is required:  
■
■
Drain the fuel tank completely, or add STA-BIL to the fuel.  
Run the engine until the gasoline in the carburetor is  
completely consumed.  
■
■
■
■
Completely drain the oil from the crankcase and refill with  
fresh oil.  
Remove the spark plug, pour 2 or 3 cc of SAE 30 oil into the  
cylinder and crank slowly to distribute the oil.  
Slowly rotate the engine a few times with the starter Rope  
and install a new plug.  
Pull out the starter rope slowly and stop at the compression  
point.  
■
■
Clean all external parts of the generating set with a cloth.  
Cover the generating set and store in a clean, dry place.  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — MAINTENANCE (ENGINE)  
UseTable 6 as a general maintenance guideline when servicing  
your engine. For more detail engine maintenance information,  
refer to the engine owner's manual supplied with your engine.  
Table 6. Engine Maintenance Schedule  
FIRST  
EVERY  
EVERY  
EVERY  
YEAR  
OR  
EVERY  
2 YEARS  
OR  
MONTH 3 MONTHS 6 MONTHS  
OR  
DESCRIPTION (3)  
OPERATION  
BEFORE  
OR  
OR  
10 HRS.  
25 HRS.  
50 HRS.  
100 HRS.  
200 HRS.  
CHECK  
CHANGE  
CHECK  
X
Engine Oil  
X
X
X
Air Cleaner  
All Nuts & Bolts  
Spark Plug  
CHANGE  
X (1)  
Re-tighten If  
Necessary  
CHECK-CLEAN  
REPLACE  
CHECK  
X
X
X
Cooling Fins  
Spark Arrester  
Fuel Tank  
CLEAN  
X
X
CLEAN  
Fuel Filter  
CHECK  
X
Idle Speed  
CHECK-ADJUST  
CHECK-ADJUST  
CHECK  
X (2)  
Valve Clearance  
Fuel lines  
X (2)  
Every 2 years (replace if necessary) (2)  
(1) Service more frequently when used in DUSTY areas.  
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically  
proficient. Refer to the HONDA Shop Manual for service procedures.  
(3) For commercial use, log hours of operation to determine proper maintenance intervals.  
PAGE 26 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — MAINTENANCE (ENGINE)  
Cleaning the Fuel Strainer  
Maintenance  
Clean the fuel strainer if it contains dust or water. Remove  
dust or water in the strainer cap and wash it in gasoline.  
Securely fasten the fuel strainer cap so that fuel will not  
leak. Check the fuel strainer every 200 hours of operation  
or once a month.  
Perform the scheduled maintenance procedures as defined  
by Table 6 and below:  
DAILY  
■
Thoroughly remove dirt and oil from the engine and control  
area. Clean or replace the air cleaner elements as  
necessary.Check and retighten all fasteners as necessary.  
Check the gearbox for oil leaks. Repair or replace as  
needed.  
DANGER  
DO NOT use gasoline as a cleaning solvent,  
because that would create a risk of fire or  
explosion.  
WEEKLY  
■
Remove the fuel filter cap and clean the inside of the fuel  
tank.  
ENGINE AIR CLEANER  
■
■
Remove or clean the filter at the bottom of the tank.  
1. Remove the air cleaner cover and foam filter element as  
shown in Figure 21.  
Remove and clean the spark plug (Figure 19), then adjust  
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This  
unit has electronic ignition, which requires no adjustments.  
2. Tap the paper filter element (Figure 21) several times on a  
hard surface to remove dirt, or blow compressed air [not  
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter  
element from the air cleaner case side. NEVER brush off  
dirt. Brushing will force dirt into the fibers. Replace the  
paper filter element if it is excessively dirty.  
Figure 19. Spark Plug Gap  
ENGINE OIL  
1. Drain the engine oil when the oil is warm as shown in  
Figure 20.  
2. Remove the oil drain bolt and sealing washer and allow  
the oil to drain into a suitable container.  
3. Replace engine oil with recommended type oil as listed  
in Table 5. For engine oil capacity, see Table 2 (engine  
specifications). DO NOT overfill.  
4. Install drain bolt with sealing washer and tighten se-  
curely.  
Figure 21. Engine Air Cleaner  
Figure 20. Engine Oil (Draining)  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — WIRING DIAGRAM (S/N 5496762 AND BELOW)  
Figure 22. Generator/Engine Wiring Diagram (S/N 5496762 and below)  
PAGE 28 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — WIRING DIAGRAM (S/N 5496763 AND ABOVE)  
Figure 23. Generator/Engine Wiring Diagram (S/N 5496763 and above)  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — TROUBLESHOOTING (ENGINE)  
diagnosis based on the Engine Troubleshooting (Table 7)  
information shown below and on the proceeding page. If  
the problem cannot be remedied, please leave the unit just  
as it is and consult our company's business office or service  
plant.  
Practically all breakdowns can be prevented by proper  
handling and maintenance inspections, but in the event of a  
breakdown, please take a remedial action following the  
TABLE 7. ENGINE TROUBLESHOOTING  
SYMPTOM  
POSSIBLE PROBLEM  
SOLUTION  
Inspect carburetor to see if fuel  
is reaching it?  
Check fuel line  
No Fuel?  
Add Fuel  
Water in fuel tank?  
Fuel filter clogged?  
Stuck carburetor?  
Spark plug is red?  
Flush or replace fuel tank.  
Replace fuel filter  
Check float mechanism.  
Poor starting  
Spark plug is fouled. Check tranistor ignition unit.  
Insufficient compression, injected air leaking. Carburetor jets are  
clogged (overflow).  
Spark plug is blue-white?  
No spark present at tip of spark  
plug?  
Tranistor ignition unit broken, high voltage cord cracked or broken.  
Start/Stop switch broken. Replace spark plug if fouled.  
No oil?  
Add oil as required.  
Oil pressure alarm lamp blinks  
upon starting?  
Check Automatic shutdown circuit "oil sensor".  
Replace cylinder and piston and if necessary axel joint.  
Tighten cylinder head connecting bolts.  
Engine will not turn over?  
Cylinder head connecting bolts  
loose?  
Cylinder head gasket damaged? Replace cylinder head gasket.  
Insufficient power output "no  
compression"  
Malfunction of valve seat?  
Spark plug is loose?  
Worn piston rings?  
Re-seat valves.  
Replace spark plug.  
Replace piston rings.  
Malfunction in air-cleaner  
system, air filter clogged?  
Clean or replace air filter.  
Air leaking in from interface  
between carburetor and cylinder  
head?  
Tighten bolts between carburetor and cylinder head. Replace  
cylinder head gasket.  
Insufficient power output  
"compression"  
Clean or replace fuel filter.  
Clean or replace carburetor.  
Check carburetor float.  
Malfunction in fuel system?  
PAGE 30 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — TROUBLESHOOTING (ENGINE)  
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)  
SYMPTOM  
POSSIBLE PROBLEM  
Malfunction in blower?  
SOLUTION  
Check or replace blower.  
Insufficient power output  
"compression" and overheats  
Air in-take filter clogged?  
Clean or replace air in-take filter.  
Over accumulation of exhaust  
products?  
Clean and check valves.  
Check muffler, replace if necessary.  
Burns to much fuel  
Wrong spark plug?  
Replace spark plug with manufactures suggested type spark plug.  
Replace lubricating oil with correct viscosity.  
Replace rings  
Lubricating oil is wrong  
viscosity?  
Exhaust color is continiously  
"WHITE"  
Worn rings?  
Air cleanner clogged?  
Clean or replace air cleaner.  
Choke valve has not been set  
to the correct position?  
Adjust choke valve to the correct position.  
Exhaust color is continiously  
"BLACK"  
Carburetor defective, seal on  
carburetor broken?  
Replace carburetor or seal.  
Adjust carburetor.  
Poor carburetor adjustment  
"engine runs too rich?  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — TROUBLESHOOTING (GENERATOR)  
diagnosis based on the Generator Troubleshooting (Table 8)  
information shown below and on the preceding page. If the  
problem cannot be remedied, please leave the unit just as it  
is and consult our company's business office or service plant.  
Practically all generator breakdowns can be prevented by  
proper handling and maintenance inspections, but in the  
event of a breakdown, please take a remedial action following  
the  
TABLE 8. GENERATOR TROUBLESHOOTING  
SYMPTOM  
Low voltage  
POSSIBLE PROBLEM  
Engine speed too low?  
SOLUTION  
Raise engine speed to rated RPM.  
AC voltmeter not working?  
Replace AC voltmeter.  
Control box internal wiring  
malfunction?  
Check control box wiring.  
Defective ignition coil?  
Check red and green ignition wires. Replace ignition wires if  
necessary.  
Low voltage. Engine speed  
normal 3650 RPM (unloaded),  
2500 RPM (idle)  
Rotor winding malfunction?  
Stator winding malfunction?  
Breaker malfunction?  
Check or replace rotor.  
Check or replace stator.  
Check or replace CB1.  
Voltage output too high.  
Engine speed too high?  
Lower engine speed to rated RPM.  
Check control box wiring.  
Voltage output too high. Engine  
speed normal 3650 RPM  
(unloaded), 2500 RPM (idle)  
Control box internal wiring  
malfunction  
Circuit breaker will not turn on  
"NO LOAD"  
Defective circuit breaker?  
Replace circuit breaker.  
Overload?  
Reduce load or replace breaker.  
Check load circuit for short.  
Check solenoid.  
Circuit breaker will turn on  
"LOADED" but trips immediately.  
Load circuit is shorted?  
Stuck solenoid?  
Does not accelerate from low to  
high "NO LOAD"  
Does not accelerate from low to  
high "LOAD ACTIVE  
Control box interal wiring  
defective?  
Check control box wiring.  
Defective rotor windings?  
Defective solenoid?  
Check or replace rotor.  
Check or replace solenoid.  
Does not decelerate no  
"VOLTAGE OUTPUT".  
Defective idle control device?  
Defective solenoid?  
Check or replace idle control device.  
Check or replace idle control device.  
Check control box wiring, replace any defective components.  
Check or replace solenoid.  
Control box wiring malfunction?  
Defective solenoid?  
Does not decelerate but has  
"VOLTAGE OUTPUT".  
Idle control device malfunction?  
Check or replace idle control device.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — EXPLANATION OF CODE IN REMARKS COLUMN  
The following section explains the different symbols and  
QTY. Column  
remarks used in the Parts section of this manual. Use the help  
numbers found on the back page of the manual if there are any  
questions.  
Numbers Used - Item quantity can be indicated by a  
number, a blank entry, or A/R.  
A/R (As Required) is generally used for hoses or other parts  
that are sold in bulk and cut to length.  
The contents and part numbers listed in the parts section are  
subject to change without notice. Multiquip does not  
guarantee the availibility of the parts listed.  
A blank entry generally indicates that the item is not sold  
separately. Other entries will be clarified in the “Remarks”  
Column.  
REMARKS Column  
Sample Parts List:  
Some of the most common notes found in the “Remarks”  
Column are listed below. Other additional notes needed to  
describe the item can also be shown.  
NO. PART NO. PART NAME  
QTY. REMARKS  
1
2
2
3
4
12345  
BOLT ...................... 1 ......INCLUDES ITEMS W/  
WASHER, 1/4 IN. .............NOT SOLD SEPARATELY  
WASHER, 3/8 IN. ... 1 ......MQ-45T ONLY  
HOSE ................... A/R ....MAKE LOCALLY  
BEARING ............... 1 ......S/N2345B AND ABOVE  
*
*
*
12347  
12348  
12349  
Assembly/Kit - All items on the parts list with the same  
unique symbol will be included when this item is purchased.  
Indicated by:  
“INCLUDES ITEMS W/(unique symbol)”  
NO. Column  
Unique Symbols - All items with same unique symbol  
Serial Number Break - Used to list an effective serial  
number range where a particular part is used.  
( , #,  
+
, %, or >) in the number column belong to the same  
*
assembly or kit, which is indicated by a note in the “Remarks”  
column.  
Indicated by:  
“S/N XXXXX AND BELOW”  
“S/N XXXX AND ABOVE”  
“S/N XXXXTO S/N XXX”  
Duplicate Item Numbers - Duplicate numbers indicate  
multiple part numbers are in effect for the same general  
item, such as different size saw blade guards in use or a  
part that has been updated on newer versions of the same  
machine.  
Specific Model Number Use - Indicates that the part is  
used only with the specific model number or model number  
variant listed. It can also be used to show a part is NOT  
used on a specific model or model number variant.  
When ordering a part that has more than one  
item number listed, check the remarks column  
for help in determining the proper part to order.  
Indicated by:  
“XXXXX ONLY”  
“NOT USED ON XXXX”  
“Make/Obtain Locally” - Indicates that the part can be  
purchased at any hardware shop or made out of available  
items. Examples include battery cables, shims, and certain  
washers and nuts.  
PART NO. Column  
Numbers Used - Part numbers can be indicated by a  
number, a blank entry, orTBD.  
“Not Sold Separately” - Indicates that an item cannot be  
purchased as a separate item and is either part of an  
assembly/kit that can be purchased, or is not available for  
sale through Multiquip.  
TBD (To Be Determined) is generally used to show a part  
that has not been assigned a formal part number at time of  
publication.  
A blank entry generally indicates that the item is not sold  
separately or is not sold by Multiquip. Other entries will be  
clarified in the “Remarks” Column.  
PAGE 34 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — SUGGESTED SPARE PARTS  
GA-2.5H 1 TO 5 UNITS WITH HONDA  
GX160K1EMA2 ENGINE  
1 to 5 Units  
Qty.  
P/N  
Description  
5 ............ 9807956846.......... SPARK PLUG  
1 ............ 15510ZE1033 ....... OIL LEVEL SWITCH  
1 ............ 15600ZE1003 ....... DIPSTICK  
1 ............ 36100ZE1015 ....... STOP SWITCH  
5 ............ 17211ZBZ000 ....... ELEMENT AIR  
5 ............ 28462ZH8003 ....... ROPE, RECOIL STARTER  
2 ............ 0601804887.......... CIRCUIT BREAKER  
2 ............ 0601812597.......... RECEPTACLE ...................... S/N 5496762 AND BELOW  
2 ............ 0601812598.......... RECEPTACLE ...................... S/N 5496763 AND ABOVE  
2 ............ 0601823204.......... RECTIFIER  
2 ............ 0810107103.......... FILTER FUEL (TANK) ........... S/N 5496762 AND BELOW  
2 ............ A9924800004 ....... FILTER FUEL (TANK) ........... S/N 5496763 AND ABOVE  
1 ............ 16950898632 ........ FUEL COCK  
5 ............ 16952883005 ........ FUEL FILTER  
1 ............ A9924800014 ....... CAP, FUEL TANK  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — NAMEPLATE AND DECALS.  
Machine Safety Decals  
The GA-2.5H portable generator is equipped with a number of safety decals (see below). These decals are provided for  
operator safety and maintenance information. The illustration below shows these decals as they appear on the machine.  
Should any of these decals become unreadable, replacements can be obtained from your dealer  
PAGE 36 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-2.5H — NAMEPLATE AND DECALS.  
NAME PLATE ASSY.  
NO.  
1
1
2
3
PART NO.  
PART NAME  
QTY.  
REMARKS  
7930505002  
A2511201002  
87528ZB2630  
1980680004  
DECAL; CONTROL PANEL ..................................... 1 ............... S/N 5496762 AND BELOW  
DECAL; CONTROL PANEL ..................................... 1 ............... S/N 5496763 AND ABOVE  
DECAL; CHOKE ...................................................... 1 ............... S/N 5496763 AND ABOVE  
DECAL; FUEL COCK .............................................. 1 ............... S-3704  
4
5
6
6
7
8
9
10  
10  
11  
12  
13  
14  
NAMEPLATE ............................................................ 1 ............... CONTACT MQ PARTS  
87533ZC0630  
7980615403  
A2561000003  
8700611804  
8700611904  
0800628504  
7900638204  
A9521200004  
7900636004  
0820610404  
35137  
DECAL; AIR CLEANER  
1
DECAL; MQ MULTIQUIP 2500 ................................ 1 ............... S/N 5496762 AND BELOW  
DECAL; MQ MULTIQUIP 2500 ................................ 1 ............... S/N 5496763 AND ABOVE  
DECAL; WARNING DANGEROUS GAS ................. 1 ............... S-4984  
DECAL; DANGER ELECTRICAL SHOCK HAZ....... 1 ............... S-4985  
DECAL: GROUND .................................................... 1 ............... S-1123  
DECAL; OPERATING INSTRUCTIONS, S-4607 ..... 1 ............... S/N 5496762 AND BELOW  
DECAL; OPERATING INSTRUCTIONS .................. 1 ............... S/N 5496763 AND ABOVE  
DECAL; CAUTION OPER. AT 3600 RPM ONLY ..... 1 ............... S-4461  
DECAL; WARNING, TRANSFER SWITCH.............. 1 ............... S-3627  
DECAL; WARNING, READ MANUAL ...................... 1 ............... S/N 5496763 AND ABOVE  
DECAL; WARNING, READ MANUAL, DSC01......... 1 ............... S/N 5496762 AND BELOW  
0820610804  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — GENERATOR ASSY .  
GENERATOR ASSY.  
PAGE 38 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — GENERATOR ASSY .  
GENERATOR ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARKS  
7931000203  
ROTOR ASSY. ............................... 1 ............. INCLUDES ITEMS W/  
*
1-1  
FIELD COIL ASSY. ......................... 1 ............. NOT SOLD SEPERATELY  
RECTIFIER ..................................... 2 ............. D3SB 80  
SURGE ABSORBER ...................... 2 ............. TNR 15G431K  
BEARING ........................................ 1 ............. 6204 2RU NY5C S30  
SET BOLT, ROTOR  
SET WASHER, BEARING  
SPRING WASHER  
ARMATURE ASSY. ......................... 1 ............. S/N 5497956 AND BELOW  
ARMATURE ASSY. ......................... 1 ............. S/N 5497957 AND ABOVE  
END BRACKET (C SIDE)  
END BRACKET (B SIDE)  
GUIDE PANEL, AIR  
COVER  
SET BOLT, STATOR  
SPRING WASHER  
PLAIN WASHER  
GROMMET  
*
1-2  
1-2  
1-3  
2
0601823213  
0601822638  
0603000040  
7681017104  
0801086004  
0040008000  
7921341803  
A2135000203  
7931315002  
7931315102  
7875021523  
7681331003  
7681344204  
0040006000  
0041206000  
7871329514  
0601851760  
0013608025  
0013608020  
0040008000  
7935420104  
0017106016  
7935420004  
0207206000  
0017108020  
*
1
1
1
3
4
5
5
6
7
8
9
10  
11  
12  
13  
14  
15  
15  
15A  
16  
17  
1
1
1
1
4
4
4
1
1
CAP  
HEX. HEAD BOLT ........................... 4 ............. S/N 5497956 AND BELOW  
HEX. HEAD BOLT ........................... 4 ............. S/N 5497957 AND ABOVE  
SPRING WASHER  
MUFFLER STAY ............................. 1 ............. S/N 5497957 AND ABOVE  
HEX. HEAD BOLT ........................... 2 ............. S/N 5497957 AND ABOVE  
MUFFLER STAY.............................. 1 ............. S/N 5497957 AND ABOVE  
4
18  
19  
20  
HEX NUT  
HEX HEAD BOLT  
2
1
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496762 AND BELOW  
CONTROL BOX ASSY. (S/N 5496762 AND BELOW)  
PAGE 40 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496762 AND BELOW  
CONTROL BOX ASSY. (S/N 5496762 AND BELOW)  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
PART NAME  
CONTROL BOX  
GROMMET  
QTY.  
1
1
REMARKS  
7931800203  
0801354504  
0601823204  
0027103020  
011106015  
7931810303  
0601800258  
0038303000  
0601804887  
3011816004  
0027104010  
0601812597  
0027104010  
0038404000  
0601815103  
0017105010  
RECTIFIER ..........................................1........... S5 VB60  
MACHINE SCREW  
HEX. HEAD BOLT ................................4........... REPLACES 0017106015  
CONTROL PANEL  
AC VOLTMETER .................................. 1........... 120/ 240V 8283  
HEX. NUT  
CIRCUIT BREAKER.............................1........... KM- 51 265V 20A  
BRACKET, CIRCUIT BREAKER  
MACHINE SCREW  
RECEPTACLE ......................................1........... 5- 20R GF- 5352(G.F.C.I.)  
MACHINE SCREW  
HEX. NUT............................................. 2........... OEMAA8  
1
1
2
9
10  
11  
12  
13  
13A  
14  
15  
1
2
2
GROUND TERMINAL  
HEX. HEAD BOLT  
1
4
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496763 AND ABOVE  
CONTROL BOX ASSY. (S/N 5496763 AND ABOVE)  
PAGE 42 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496763 AND ABOVE  
CONTROL BOX ASSY. (S/N 5496763 AND ABOVE)  
NO  
1
2
3
4
5
6
7
8
PART NO  
PART NAME  
CONTROL BOX  
GROMMET  
RECTIFIER ............................................... 1 ................. S5VB60  
MACHINE SCREW  
CONTROL PANEL  
CIRCUIT BREAKER ................................. 1 ................. KM-51 : 20A  
BRACKET, CIRCUIT BREAKER  
MACHINE SCREW  
AC VOLTMETER ...................................... 1 ................. DE450-011 : 0 ~ 120V  
RECEPTACLE........................................... 1 ................. 5-20R: 125V, 20A  
RECEPTACLE........................................... 1 ................. L5-20R:125V, 20A  
MACHINE SCREW  
HEX NUT  
QTY.  
1
1
REMARKS  
A0101000103  
0801354504  
0601823204  
0027103012  
A2224000103  
0601804887  
3011816004  
0021004010  
0601806819  
0601812598  
0601812592  
0021004010  
0207004000  
0021004015  
0207004000  
0017106016  
0017105010  
1
1
1
2
9
10  
11  
12  
12A  
13  
13A  
14  
15  
4
4
4
1
4
4
MACHINE SCREW  
HEX NUT  
HEX. HEAD BOLT  
HEX. HEAD BOLT  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496762 AND BELOW  
PIPE FRAME ASSY. (S/N 5496762 AND BELOW)  
PAGE 44 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496762 AND BELOW  
PIPE FRAME ASSY. (S/N 5496762 AND BELOW)  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
PART NAME  
QTY.  
REMARKS  
7935400302  
0801886104  
7935419204  
7935419304  
020108060  
7935510102  
0810106004  
0810107103  
0602125031  
16950898632  
PIPE FRAME  
1
2
2
2
WASHER  
RUBBER SUSPENSION  
RUBBER SUSPENSION  
HEX. NUT............................................. 8........... REPLACES 0207208000  
FUEL TANK  
CAP, FUEL TANK  
FUEL FILTER  
FUEL GAUGE ......................................1........... CJ-13  
FUEL COCK  
CUP  
FILTER  
1
1
1
9
10  
1
1
1
1
2
1
2
2
10- 1 16081471831  
10- 2 16952883005  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
21A  
22  
23  
24  
950014500160M HOSE  
9500202080  
90854ZB2000  
7855525514  
7855525604  
011208030  
011008020  
7935421004  
0017106016  
0017106016  
0017106016  
0040506000  
020108060  
011208025  
0040008000  
HOSE BAND  
GROMMET  
RUBBER WASHER  
COLLAR  
HEX. HEAD BOLT ................................2........... REPLACES 0017108030  
HEX. HEAD BOLT ................................2........... REPLACES 0017108020  
BRACKET, MUFFLER COVER  
HEX. HEAD BOLT  
HEX. HEAD BOLT  
HEX. HEAD BAOLT  
TOOTH WASHER  
HEX. NUT  
1
2
3
1
1
2
REPLACES 0031308000  
HEX. HEAD BOLT ................................2........... REPLACES 0011308025  
SPRING WASHER  
2
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496763 AND ABOVE  
PIPE FRAME ASSY. (S/N 5496763 AND ABOVE)  
PAGE 46 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496763 AND ABOVE  
PIPE FRAME ASSY. (S/N 5496763 AND ABOVE)  
NO.  
1
2
3
4
PART NO.  
PART NAME  
QTY.  
1
2
REMARKS  
A2417000202  
7935419204  
020108060  
PIPE FRAME  
RUBBER SUSPENSION  
HEX. NUT............................................................ 4 ........ REPLACES 0207208000  
RUBBER SUSPENSION ..................................... 2  
7935419304  
020108060  
5
HEX. NUT............................................................ 4 ........ REPLACES 0207208000  
6
7
8
9
A2364000002  
A9924800014  
A9924800004  
0602125034  
16950898632  
FUEL TANK  
CAP, FUEL TANK  
FUEL FILTER  
FUEL GAUGE ..................................................... 1 ........ CJ-58A  
FUEL COCK  
CUP, FUEL STRAINER  
FILTER N/C  
1
1
1
10  
1
1
1
1
2
2
2
10- 1 16081471831  
10- 2 16952883005  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
950014518040 HOSE  
9500202080  
7855525514  
7855525604  
011208030  
011008020  
7935421004  
0017106016  
0017106016  
0019206016  
0011308020  
0040008000  
020108060  
HOSE BAND  
RUBBER CUSHION  
COLLAR  
HEX. HEAD BOLT ............................................... 2 ........ REPLACES 0017108030  
HEX. HEAD BOLT ............................................... 2 ........ REPLACES 0017108020  
BRACKET, MUFFLER COVER  
HEX. HEAD BOLT  
HEX. HEAD BOLT  
HEX. HEAD BOLT  
1
2
3
1
2
2
HEX. HEAD BOLT  
WASHER, LOCK  
HEX. NUT............................................................ 2 ........ REPLACES 0031308000  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CYLINDER HEAD ASSY.  
CYLINDER HEAD ASSY.  
PAGE 48 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CYLINDER HEAD ASSY.  
CYLINDER HEAD ASSY.  
NO  
PART NO  
PART NAME  
QTY.  
REMARKS  
1
12210ZH8020  
12204ZE1306  
12205ZE1315  
12216ZE5300  
12251ZF1800  
12310ZE1010  
12391ZE1000  
15721732000  
90013883000  
90043ZB2003  
90047ZE1000  
9430110160  
957230806000  
9807956846  
9807956855  
HEAD COMP., CYLINDER ........................ 1 .........INCLUDES ITEMS W/  
*
2
*
3
*
4
*
5
6
7
GUIDE, IN. VALVE (OVER SIZE)  
GUIDE, IN. VALVE  
CLIP, VALVE GUIDE  
GASKET, CYLINDER HEAD  
COVER COMP, HEAD  
PACKING, HEAD COVER  
TUBE, BREATHER  
BOLT, FLANGE 6X12  
BOLT, STUD 6X94  
BOLT, STUD 8X32  
PIN, DOWEL 10X1  
BOLT, FLANGE 8X60  
PLUG, SPARK (BPR6ES NGK)  
PLUB, SPARK (W20EPR-U ND)  
1
1
1
1
1
1
1
4
2
2
2
4
1
1
8
9
10  
11  
12  
13  
14  
14  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CYLINDER BARREL ASSY.  
CYLINDER BARREL ASSY.  
PAGE 50 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CYLINDER BARREL ASSY.  
CYLINDER BARREL ASSY.  
NO  
2
3
PART NO  
PART NAME  
BARREL ASSY, CYLINDER ................................1......... INCLUDES ITEMS W/  
SWITCH ASSY, OIL LEVEL  
QTY.  
REMARKS  
12000ZH8406  
15510ZE1033  
16510ZE1000  
#
1
4
GOVERNOR ASSY. .............................................1......... USE UP TO S/N 4913229  
......................................................................................... INCLUDES ITEMS W/  
GOVERNOR ASSY. ............................................. 1......... USE FROM S/N 4913230  
*
4
16506ZL0000  
......................................................................................... INCLUDES ITEMS W/  
*
5
*
6
*
7
*
8
16511ZE1000  
16512ZE1000  
16513ZE1000  
16531ZE1000  
16541ZE1000  
90131ZE1000  
90451ZE1000  
90601ZE1000  
90602ZE1000  
91001ZF1003  
91201Z0T801  
91353671004  
9405010000  
WEIGHT, GOVERNOR  
HOLDER, GOVENOR WEIGHT  
PIN, GOVERNOR WEIGHT  
SLIDER, GOVERNOR  
SHAFT, GOVERNOR ARM  
BOLT, DRAIN PLUG  
2
1
2
1
1
2
1
2
1
1
1
1
1
2
1
2
1
9
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
WASHER, THRUST 6MM  
WASHER, DRAIN PLUG 10.2MM  
CLIP, GOVERNOR HOLDER  
BEARING, RADIAL BALL(6205TMB)  
OIL SEAL 25X41X6  
#
#
O-RING, 13.5X1.5  
NUT, FLANGE, 10MM  
9410106800  
9425108000  
957010601200  
06111ZH8405  
WASHER, PLAIN, 6MM  
PIN, LOCK, 8MM  
BOLT, FLANGE, 6X12  
GASKET KIT  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CRANKCASE COVER ASSY.  
CRANKCASE COVER ASSY.  
PAGE 52 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CRANKCASE COVER ASSY.  
CRANKCASE COVER ASSY.  
NO  
1
3
PART NO  
PART NAME  
QTY.  
REMARKS  
11300ZE1634  
11381ZH8801  
15600ZE1003  
15600ZG4003  
15625ZE1003  
91201Z0T801  
9430108140  
957010803200  
961006205000  
COVER ASSY, CRANKCASE ............................. 1 ............ INCLUDES ITEMS W/  
*
#
GASKET, CASE COVER  
CAP ASSY, OIL FILLER ...................................... 1 ............ INCLUDES ITEMS W/  
CAP, OIL FILLER  
GASKET, OIL FILLER CAP  
OIL SEAL, 25X41X6  
PIN, DOWEL 8X14  
BOLT, LANGE 8X32  
BEARING, RADIAL BALL, 6205  
1
4
5
1
1
1
2
6
1
8
9
#
*
10  
11  
12  
*
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CRANKSHAFT ASSY.  
CRANKSHAFT ASSY.  
PAGE 54 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CRANKSHAFT ASSY.  
CRANKSHAFT ASSY.  
NO  
1
PART NO  
13310ZB2000  
PART NAME  
CRANKSHAFT (VE-TYPE)  
QTY. REMARKS  
1
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — PISTON ASSY.  
PISTON ASSY.  
PAGE 56 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — PISTON ASSY.  
PISTON ASSY.  
NO  
1
1
1
1
2
2
2
2
3
4
5
6
PART NO  
PART NAME  
QTY.  
REMARKS  
13010ZF1023  
13011ZF1023  
13012ZF1023  
13013ZF1023  
13101ZH8010  
13101ZH8010  
13103ZH8000  
13102ZH8010  
13111ZE1000  
132000ZE1010  
90001ZE1000  
90551ZE1000  
RING SET, PISTON (STD)  
RING SET, PISTON (0.25)  
RING SET, PISTON (0.50)  
RING SET, PISTON (0.75)  
PISTON (STD)  
1
1
1
1
1
1
1
1
1
1
2
2
PISTON (0.25)  
PISTON (0.50)  
PISTON (0.75)  
PIN, PISTON  
ROD ASSY, CONNECTING  
BOLT, CONNECTING ROD  
CLIP, PISTON PIN, 18MM  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CAMSHAFT ASSY.  
CAMSHAFT ASSY.  
PAGE 58 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CAMSHAFT ASSY.  
CAMSHAFT ASSY.  
NO  
1
1
2
3
4
5
6
7
PART NO  
PART NAME  
QTY.  
REMARKS  
14100ZE1812  
14100ZL0000  
14410ZE1010  
14431ZE1000  
14441ZE1000  
14451ZE1013  
14568ZE1000  
14711ZF1000  
14721ZF1000  
14751ZF1000  
14771ZE1000  
14773ZE1000  
14781ZE1000  
14791ZE1010  
90012ZE0010  
90206ZE1000  
12209ZH8003  
CAM SHAFT ASSY.............................................. 1 ............ UP TO S/N 4913229  
CAM SHAFT ASSY.............................................. 1 ............ FROM S/N 4913230  
ROD, PUSH  
ARM, VALVE ROCKER  
LIFTER, VALVE  
PIVOT, ROCKER ARM  
SPRING, WEIGHT RETURN  
VALVE, IN  
2
2
2
2
1
1
1
2
1
1
1
1
2
2
1
8
9
VALVE, EX  
SPRING, VALVE  
10  
11  
12  
13  
14  
15  
18  
RETAINER, IN. VALVE SPRING  
RETAINER, EX. VALVE SPRING  
ROTATOR, VALVE  
PLATE, PUSH ROD GUIDE  
BOLT, PIVOT (8MM)  
NUT, PIVOT ADJUSTING  
VALVE STEM  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — RECOIL STARTER ASSY.  
RECOIL STARTER ASSY.  
PAGE 60 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — RECOIL STARTER ASSY.  
RECOIL STARTER ASSY.  
NO  
1
2
3
4
5
6
7
8
PART NO  
PART NAME  
QTY. REMARKS  
28400ZH8013ZB  
28410ZH8003ZB  
28420ZH8013  
28422ZH8013  
28433ZH8003  
28441ZH8003  
28442ZH8003  
28443ZH8003  
28461ZH8003  
28462ZH8003  
90003ZH8003  
90008ZE2003  
STARTER ASSY, RECOIL “NH1” BLACK  
CASE, RECOIL STARTER “NH1” BLACK  
REEL, RECOIL STARTER  
RATCHET, STARTER  
1
1
1
2
1
1
1
2
1
1
1
3
GUIDE, RATCHET  
SPRING, FRICTION  
SPRING, RECOIL STARTER  
SPRING, RETURN  
KNOB, RECOIL STARTER  
ROPE, RECOIL STARTER  
SCREW, SETTING  
9
10  
12  
13  
BOLT, FLANGE 6X10  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — FAN COVER ASSY.  
FAN COVER ASSY.  
PAGE 62 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — FAN COVER ASSY.  
FAN COVER ASSY.  
NO  
PART NO  
PART NAME  
SPRING, CONTROL ADJUSTING  
COVER, FAN “NH1” BLACK  
PLATE, SIDE ALERT & LAMP ............ 1 ............... USE FROM S/N 475372719  
PLATE, SIDE LAMP ............................ 1 ............... USE FROM S/N 4795906~5372718  
PLATE, SIDE ALERT & LAMP ............ 1 ............... USE UP TO S/N 4795905  
CLAMP, CORD .................................... 1 ............... USE UP TO S/N 4367320  
CLAMP, CORD .................................... 1 ............... USE FROM S/N 4367321  
QTY.  
1
1
REMARKS  
3
*
4
7
7
7
10  
10  
11  
12  
16584883300  
19610ZE1000ZC  
19611ZH8820  
19612ZH8821  
19612ZH8830  
19613ZE1010  
90601ZH7013  
19630ZB2000  
19640ZB2010  
SHROUD COMP., LOWER  
SHROUD ASSY., UPPER ................... 1 ............... USE UP TO S/N 5048024  
1
` .............................................................................. INCLUDES ITEMS W/  
SHROUD ASSY., UPPER ................... 1 ............... USE FROM S/N 5048025  
*
12  
19640ZH8R60  
............................................................................... INCLUDES ITEMS W/  
SUB HARNESS................................... 1 ............... USE UP TO S/N 4367320  
ENGINE, STOP SWITCH .................... 1 ............... USE UP TO S/N 4368640  
ENGINE, STOP SWITCH .................... 1 ............... USE FROM S/N 4368641  
*
13  
14  
14  
17  
18  
19  
32197ZH8003  
36100ZE1015  
36100ZH7003  
90013883000  
90022888010  
93500050350A  
93500050400G  
957010600800  
34150ZH7003  
957010600800  
BOLT, FANGE 6X12  
BOLT, FLANGE 6X20  
8
1
SCREW, PAN 5X35 ............................. 1 ............... USE UP TO S/N 5048024  
SCREW, PAN 5X40 ............................. 1 ............... USE FROM S/N 5048025  
*
19  
21  
23  
24  
*
BOLT, FLANGE 6X8  
1
ALERT UNIT, OIL ................................ 1 ............... USE FROM S/N 5372719  
BOLT, FLANGE 6X8 ............................ 1 ............... USE FROM S/N 5372719  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CARBURETOR ASSY.  
CARBURETOR ASSY.  
PAGE 64 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — CARBURETOR ASSY.  
CARBURETOR ASSY.  
NO  
PART NO  
PART NAME  
QTY.  
REMARKS  
1
2
3
4
4
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
#%  
+
16010ZB1015  
16011ZE0005  
16013ZE0005  
16015ZE0831  
16015ZE1811  
16016ZH7W01  
16024ZE1811  
16028ZE0005  
16044ZE0005  
16100ZH8E81  
16124ZE0005  
16166ZH8E80  
16211ZE1000  
16212ZH8800  
16221ZH8801  
16269ZE1800  
16610ZB2000  
9430520122  
GASKET SET  
VALVE SET, FLOAT  
FLOAT SET  
1
1
1
*
*
*
*
*
CHAMBER SET, FLOAT ................................1 .......... USE FROM S/N BE67A A  
CHAMBER SET, FLOAT ................................1 .......... USE FROM S/N BE51A A  
SCREW SET  
SCREW SET, DRAIN.....................................1 .......... INCLUDES ITEMS W/  
SCREW SET, B .............................................1 .......... INCLUDES ITEMS W/+  
CHOKE SET  
CARBURETOR ASSY,(BE67A B) ..................1 .......... INCLUDES ITEMS W/  
SCREW, THROTTLE STOP  
NOZZLE, MAIN  
INSULATOR, CARBURETOR  
GASKET, INSULATOR  
GASKET, CARBURETOR  
GASKET, AIR CLEANER  
1
%
1
*
*
1
1
1
1
1
1
*
*
LEVER COMP., CHOKE ................................1 .......... INCLUDES ITEMS W/ <  
PIN, SPRING 2X12  
JET, MAIN, #70, OPTION  
JET, MAIN, #72, OPTION  
JET, MAIN, #75,  
18 <  
19  
19  
1
1
1
1
99101ZH80700  
99101ZH80720  
99101ZH80750  
99204ZE00350  
19  
20  
*
*
JET SET, PILOT, #35 .....................................1 .......... INCLUDES ITEMS W/#  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
PAGE 66 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
NO  
1
2
3
4
5
6
7
8
PART NO  
PART NAME  
QTY.  
REMARKS  
17211ZB2000  
17212ZB2000  
17220ZB2000  
17231ZB2000  
17239ZB2000  
17252ZB2000  
90115459770  
9405006080  
957010601000  
ELEMENT, AIR CLEANER  
SEPARATOR, AIR CLEANER  
CASE COMP., AIR CLEANER  
COVER AIR CLEANER  
STAY AIR CLEANER  
SEAL, AIR CLEANER  
BOLT, SETTING  
1
1
1
1
1
1
4
2
1
BOLT, FLANGE, 6MM  
BOLT, FLANGE, 6X10  
9
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — MUFFLER ASSY.  
MUFFLER ASSY.  
PAGE 68 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — MUFFLER ASSY.  
MUFFLER ASSY.  
NO  
1
2
3
4
5
6
8
9
PART NO  
PART NAME  
QTY.  
REMARKS  
18310ZB3C00  
18320ZB2000  
18325ZH8T90  
18329ZB2000  
18330ZH8T90  
18355898630  
18381ZE1800  
18381ZH8800  
MUFFLER COMP.  
1
1
1
2
1
1
1
1
PROTECTOR, MUFFLER OUTER  
PROTECTOR, MUFFLER INNER  
SEAL, MUFFLER PROTECTOR  
PIPE COMP., EX  
ARRESTER, SPARK  
GASKET, MUFFLER  
GASKET, MUFFLER  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — FLYWHEEL ASSY.  
PAGE 70 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — FLYWHEEL ASSY.  
FLYWHEEL ASSY.  
NO  
1
2
3
4
PART NO  
PART NAME  
KEY, SPECIAL WOOD RUFF, 25X18  
FAN, COOLING  
PULLEY, STARTER  
FLYWHEEL (LAMP)  
NUT, SPECIAL, 14MM  
QTY.  
REMARKS  
13331357000  
19511ZE1000  
28451ZH8003  
31100ZE1811  
90201878003  
1
1
1
1
1
5
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — IGNITION COIL ASSY.  
IGNITION COIL ASSY.  
PAGE 72 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — IGNITION COIL ASSY.  
IGNITION COIL ASSY.  
NO  
1
2
4
6
PART NO  
PART NAME  
QTY. REMARKS  
30500ZE1043  
30700ZE1013  
31510ZE1811  
31511ZE1000  
31512ZE1000  
90015883000  
90019883000  
90121952000  
36101ZE1010  
COIL ASSY., IGNITION  
CAP ASSY., NOISE SUPPRESSOR  
COIL ASSY., LAMP (12V25W)  
CLAMP, WIRE  
1
1
1
1
1
2
1
2
7
GROMMET, WIRE  
12  
13  
14  
15  
BOLT, FLANGE, 6X28  
BOLT, FLANGE, 5X10  
BOLT, FLANGE, 6X25  
WIRE, STOP SWITCH  
`
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — GOVERNOR/CONTROL ASSY.  
GOVERNOR/CONTROL ASSY.  
PAGE 74 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — GOVERNOR/CONTROL ASSY.  
GOVERNOR/CONTROL ASSY.  
NO  
1
1
2
3
3
3
4
5
PART NO  
PART NAME  
QTY.  
REMARKS  
16551ZE0010  
16551ZL0010  
16555ZE1000  
16561ZH8D00  
16561ZL0U30  
16561ZL0000  
16562ZE1020  
90015ZE5010  
9405006000  
ARM, GOVERNOR.................................... 1 ......... USE UP TO S/N 4913229  
ARM, GOVERNOR.................................... 1 ......... USE FROM S/N 4913230  
ROD, GOVERNOR  
1
SPRING, GOVERNOR .............................. 1 ......... USE UP TO S/N 4913229  
SPRING, GOVERNOR .............................. 1 ......... USE FROM S/N 4913230~5048024  
SPRING, GOVERNOR .............................. 1 ......... USE FROM S/N 5048025  
SPRING, THROTTLE RETURN  
BOLT, GOVERNOR ARM  
NUT, FLANGE, 6MM  
1
1
1
6
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — LABELS ASSY.  
PAGE 76 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160K1EMA2 ENGINE — LABELS ASSY.  
IGNITION COIL ASSY.  
NO  
1
12  
21  
PART NO  
PART NAME  
QTY.  
REMARKS  
87521ZH8020  
87528ZB2630  
87533ZC0630  
EMBLEM, 5.5 HP  
DECAL, CHOKE  
DECAL, AIR CLEANER  
1
1
1
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TERMS AND CONDITIONS OF SALE — PARTS  
PAYMENT TERMS  
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell  
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal  
any), and with Multiquip part numbers Equipment Manufacturer accounts who use  
Terms of payment for parts are net 30 days.  
FREIGHTPOLICY  
clearlymarked.  
our products as integral parts of their own  
products.  
All parts orders will be shipped collect or  
prepaidwiththechargesaddedtotheinvoice.  
All shipments are F.O.B. point of origin.  
Multiquip’sresponsibilityceaseswhenasigned  
manifesthasbeenobtainedfromthecarrier,  
andanyclaimforshortageordamagemustbe  
settledbetweentheconsigneeandthecarrier.  
6. Thefollowingitemsarenotreturnable:  
SPECIALEXPEDITINGSERVICE  
a. Obsolete parts. (If an item is in the  
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice  
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,  
insuredparcelpostorincaseswhereMultiquip  
mustpersonallydeliverthepartstothecarrier.  
(such as gaskets, seals, “O” rings,  
b. Any parts with a limited shelf life  
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY  
MINIMUMORDER  
chasedmorethansixmonthspriorto  
thereturndate.  
Multiquip shall not be liable hereunder for  
damagesinexcessofthepurchasepriceofthe  
TheminimumchargeforordersfromMultiquip  
is $15.00 net. Customers will be asked for  
instructionsregardinghandlingofordersnot  
meetingthisrequirement.  
c. Anylineitemwithanextendeddealer item with respect to which damages are  
netpriceoflessthan$5.00.  
claimed, and in no event shall Multiquip be  
liable for loss of profit or good will or for any  
otherspecial,consequentialorincidentaldam-  
ages.  
d. Special order items.  
RETURNEDGOODSPOLICY  
e. Electricalcomponents.  
f. Paint,chemicals,andlubricants.  
g. Decalsandpaperproducts.  
h. Itemspurchasedinkits.  
Returnshipmentswillbeacceptedandcredit  
willbeallowed,subjecttothefollowingprovi-  
sions:  
LIMITATIONOFWARRANTIES  
Nowarranties,expressorimplied,aremade  
in connection with the sale of parts or trade  
accessoriesnorastoanyenginenotmanufac-  
tured by Multiquip. Such warranties made in  
connectionwiththesaleofnew,completeunits  
are made exclusively by a statement of war-  
rantypackagedwithsuchunits,andMultiquip  
neitherassumesnorauthorizesanypersonto  
assume for it any other obligation or liability  
whatever in connection with the sale of its  
products.Apartfromsuchwrittenstatementof  
warranty, there are no warranties, express,  
impliedorstatutory,whichextendbeyondthe  
descriptionoftheproductsonthefacehereof.  
1. AReturnedMaterialAuthorizationmust  
be approved by Multiquip prior to ship-  
ment.  
7. Thesenderwillbenotifiedofanymaterial  
receivedthatisnotacceptable.  
2. ToobtainaReturnMaterialAuthorization,  
alistmustbeprovidedtoMultiquipParts  
Salesthatdefinesitemnumbers,quanti-  
ties, and descriptions of the items to be  
returned.  
8. Suchmaterialwillbeheldforfiveworking  
days from notification, pending instruc-  
tions.Ifareplyisnotreceivedwithinfive  
days,thematerialwillbereturnedtothe  
senderathisexpense.  
a. Thepartsnumbersanddescriptions  
must match the current parts price  
list.  
9. Creditonreturnedpartswillbeissuedat  
dealer net price at time of the original  
purchase,lessa15%restockingcharge.  
b. The list must be typed or computer  
generated.  
10. In cases where an item is accepted, for  
which the original purchase document  
can not be determined, the price will be  
basedonthelistpricethatwaseffective  
twelvemonthspriortotheRMAdate.  
c. The list must state the reason(s) for  
thereturn.  
Effective: February 22, 2006  
d. The list must reference the sales  
order(s)orinvoice(s)underwhichthe  
itemswereoriginallypurchased.  
11. Credit issued will be applied to future  
purchasesonly.  
e. The list must include the name and  
phonenumberofthepersonrequest-  
ingtheRMA.  
PRICINGANDREBATES  
Prices are subject to change without prior  
notice.Pricechangesareeffectiveonaspe-  
cificdateandallordersreceivedonorafterthat  
datewillbebilledattherevisedprice.Rebates  
3. AcopyoftheReturnMaterialAuthoriza-  
tionmustaccompanythereturnshipment.  
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice  
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand  
Multiquip’sdesignatedreceivingpoint.  
atthetimeofanypricechange.  
PAGE 78 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION AND PARTS MANUAL  
HERE’S HOW TO GET HELP  
PLEASE HAVETHE MODEL AND SERIAL  
NUMBER ON-HANDWHEN CALLING  
UNITED STATES  
Multiquip Corporate Office  
18910 Wilmington Ave.  
Carson, CA 90746  
MQ Parts Department  
800-427-1244  
Tel. (800) 421-1244  
Fax (800) 537-3927  
Fax: 800-672-7877  
Fax: 310-637-3284  
310-537-3700  
Contact: [email protected]  
Mayco Parts  
800-306-2926  
310-537-3700  
Warranty Department  
800-421-1244, Ext. 279 Fax: 310-537-1173  
310-537-3700, Ext. 279  
Fax: 800-672-7877  
Fax: 310-637-3284  
Service Department  
800-421-1244  
Technical Assistance  
800-478-1244  
Fax: 310-537-4259  
Fax: 310-631-5032  
310-537-3700  
MEXICO  
MQ Cipsa  
Carr. Fed. Mexico-Puebla KM 126.5  
Momoxpan, Cholula, Puebla 72760 Mexico Fax: (52) 222-285-0420  
Contact: [email protected]  
UNITED KINGDOM  
Multiquip (UK) Limited Head Office  
Hanover Mill, Fitzroy Street,  
Ashton-under-Lyne,  
Tel: (52) 222-225-9900  
Tel: 0161 339 2223  
Fax: 0161 339 3226  
Lancashire OL7 0TL  
Contact: [email protected]  
CANADA  
Multiquip  
4110 Industriel Boul.  
Laval, Quebec, Canada H7L 6V3  
Contact: [email protected]  
BRAZIL  
Multiquip  
Tel: (450) 625-2244  
Fax: (450) 625-8664  
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055  
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055  
Contact: [email protected], [email protected]  
© COPYRIGHT 2008, MULTIQUIP INC.  
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the  
property of their respective owners and used with permission.  
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.  
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data  
contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or  
the information published in this publication at any time without notice and without incurring any obligations.  
Your Local Dealer is:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miller Electric Welder 230Volt User Manual
Milwaukee Sander 58 01 1270 User Manual
NordicTrack Home Gym NTEVEL59011 User Manual
Omega Vehicle Security Thermometer DP97 User Manual
Omnimount Indoor Furnishings MWFS User Manual
Oregon Scientific Watch SL210 User Manual
Palsonic Flat Panel Television TFTV812U User Manual
Panasonic All in One Printer DP MB350 User Manual
Panasonic Electric Shaver ES2025 User Manual
Panasonic Fax Machine KX F900 User Manual