Start Here
Easy Setup Instructions
Photo All-In-One
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the machine with your computer.
Important
When cleaning the exterior of the machine, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Machine” in the Quick Start Guide.
Unpack the Machine
1
Prepare the Machine
2
Install the Print Head
3
Install the Ink Tanks
4
Align the Print Head
Note
Important
d Use the { or } button on the Operation Panel to
a Remove the Print Head from its package.
a Pinch the Paper Guide and slide it to the left end.
For the ink tanks compatible with this machine, refer to the back
cover of the Quick Start Guide.
Before turning on the machine, remove all the orange shipping
tapes.
select the language for the LCD, then press the
OK button.
Paper Support
a Pull the orange tape in the direction of the arrow
to peel off the protective film and remove the film
completely.
a Unlock the Scanning Unit (Printer Cover).
(1) Open the Document Cover.
Extension
(2) Move the Scanner Lock Switch towards the release mark to
unlock the Scanning Unit (Printer Cover).
Paper Guide
(2)
Caution
(1) Press the { or }
button to select the
language.
There may be some transparent or light blue ink on the inside
of the bag the print head comes in, or the inside of the protec-
tive cap - this has no effect on print quality. Be careful not to
get ink on yourself when handling these items.
(1)
If the air hole is blocked with the remaining film, ink
may leak out or may not eject properly.
b Remove the orange protective cap from the Print
(2) Press the OK
button.
Head and discard it.
b Twist off and discard the orange protective cap
Electrical Contacts
located on the bottom of the ink tank.
Important
Scanning Unit
(Printer Cover)
Protective Cap
If an unintended language is displayed on the LCD, press the
Back button on the Operation Panel to return to the Language
selection screen.
Ink Port
b Load a sheet of A4 or Letter-sized plain paper
into the Rear Tray, align the paper with the Cover
Guide on the right side, then slide the Paper
Guide against the paper.
Do not press!
Once the message “Install the print head and set the ink
tank.” appears, go to e.
Caution
Print Head Nozzles
Protective Cap
• Make sure to unlock the Scanning Unit (Printer Cover) before
turning on the machine.
• Before transporting the machine, always lock the Scanning
Unit (Printer Cover) by moving the Scanner Lock Switch
towards the lock mark.
Electrical Contacts
e Lift the Scanning Unit (Printer Cover) until it locks
into place. The Print Head Holder moves to the
center.
Paper Guide
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
Print Side
Important
Do not touch the print head nozzles or the electrical contacts.
c Insert the ink tank into the right-hand slot and
c Firmly raise the Print Head Lock Lever until
it stops. The Print Head Lock Lever may feel
heavy.
b Plug the power cord in the back of the machine
and connect the other end to the wall outlet.
Next, open the Sheet Feeder Cover, pull out the
Paper Support and the Extension, then open the
Paper Output Tray and the Extension.
Cover Guide
press the
mark on the ink tank until it clicks
into place.
Extension
Document Cover
c Make sure that Yes is selected in the message
requesting head alignment, then press the OK
button.
Paper Support
d Insert the Print Head.
d Make sure the ink lamp lights red.
Paper Output Tray
Extension
Sheet Feeder
Cover
Refer to the color
guide on the Print
Head Lock Lever.
Do not touch!
Important
• Make sure that the Document Cover is closed.
• Do NOT connect the USB cable at this stage.
Caution
c Open the Operation Panel, then press the ON/
OFF button to turn on the machine.
For your safety, always firmly grip the areas illustrated when
lifting the Scanning Unit (Printer Cover).
Note
e Push the Print Head to hold it in place, and lower
Print Head alignment takes about 6 minutes to complete. Do not
start another operation until the machine has stopped making
operating noises.
The machine will initialize. Wait until the Power lamp stops
flashing and remains lit blue.
the Print Head Lock Lever.
e Close the Scanning Unit (Printer Cover).
Important
If the Document Cover is opened, you cannot open the Scan-
ning Unit (Printer Cover). Be sure to open the Scanning Unit
(Printer Cover) with the Document Cover closed.
The pattern is printed. And Print Head is aligned
automatically.
f Write down the serial number located inside
the machine. You will need this to register your
product.
OK
Caution
For your safety, always firmly grip the areas illustrated when
closing the Scanning Unit (Printer Cover).
Important
If the Scanning Unit (Printer Cover) is left open for more than
10 minutes, the Print Head Holder moves to the right. Close
and reopen the Scanning Unit (Printer Cover) to return the
Holder to the center.
Important
The machine starts the preparatory operation. It takes about 2
minutes. Do not start another operation until the machine has
stopped making operating noises.
Note
• The pattern is printed in black and blue.
• When Automatic Print Head Alignment cannot be executed
correctly, the message “Auto head align has failed.” is displayed
on the LCD. Refer to “An Error Message is Displayed on the LCD”
in the Quick Start Guide.
Serial Number Location
Hardware setup and Print Head alignment are
complete.
|