Hotpoint Washer Hotpoint Washing Machine User Manual

Instructions for use

WASHING MACHINE

Contents

Installation, 2-3-4-5-6-7

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

English,1

Technical data

Instructions for the fitter

Care and maintenance, 8

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 9

General safety

BHWMD 732

Disposal

Opening the porthole door manually

Description of the washing machine, 10-11

Control panel

Display

Running a wash cycle, 12

Wash cycles and functions, 13

Table of wash cycles

Wash functions

Detergents and laundry, 14

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 15-16

Assistance, 17

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the drain hose

Connect the drain

• the socket is compatible with the washing

machine’s plug. If this is not the case, repla-

ce the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the ap-

pliance please read the instructions below.

hose, without ben-

ding it, to a draining

duct or a wall drain

situated between 65

and 100 cm from the

floor;

65 - 100 cm

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

The drain hose may

be connected to an

under-sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends

have been taken off

the spigot.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be

of the correct colour as indicated by the colou-

red marking or the colour that is embossed in

words on the base of the plug. Replacements

can be obtained directly from your nearest

Service Depot.

If it is placed over

the edge of a basin

or sink be sure the

free end of the hose

should not be under-

water.

Removing the plug:

If your appliance has a non-rewireable moul-

ded plug and you should wish to re-route the

mains cable through partitions, units etc.,

please ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of ap-

proval.

! We advise against the use of hose extensions;

in case of absolute need, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed

down too far, this may cause the machine to self

-syphon ie. continuously empty as it is filling.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicatedon the Tech-

nical Data Plate fixed on the machine;

• the supply voltage is included within the

values indicated on the Technical Data Plate

fixed on the machine.

Instructions for connecting cable to an alternati-

ve plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow Earth

Blue

Brown

Neutral

Live

Download from Www.Somanuals.com. All Manuals Search And Download.

As the colours of the wires in the lead may not

correspond with the coloured markings iden-

tifying the terminals in your plug, proceed as

follows:

! The power supply cable must only be repla-

ced by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

Connect Green & Yellow wire to terminal

marked E or or coloured Green or Green &

Yellow.

The first wash cycle

Connect Brown wire to terminal marked L or

coloured Red.

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

Connect Blue wire to terminal marked N or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a

wash cycle

(60°C).

13 amp fuse, either in the plug or adaptor or

at the distribution board.

Technical data

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

Model

BHWMD 732

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

width 59.5 cm

Dimensions height 81.5 cm

depth 54.5 cm

BLUE

NEUTRAL (N)

LIVE (L)

EARTH (E)

BROWN

Capacity

from 1 to 7 kg

GREEN & YELLOW

please refer to the technical

data plate fixed to the ma-

chine

Electrical

GREEN &

YELLOW

connections

13 ampere fuse

BROWN

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 52 litres

CROSS-BAR

CORD GRIP

BLUE

Water con-

nections

up to 1300 rotations per

minute

Spin speed

Disposing of the appliance:

Test wash

cycles in

accordan-

ce with

When disposing of the appliance please remove

the plug by cutting the mains cable as close as

possible to the plug body and dispose of it as

described above.

programme ; temperatu-

re 60°C (2nd press of the

button);

temperature 40°C (3rd press

of the button).

directives

1061/2010

and

! The washing machine should not be installed

in an outdoor environment, not even where

the area is sheltered, because it may be very

dangerous to leave it exposed to damp, rain

and thunderstorms.

1015/2010

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electromagne-

tic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

! When the washing machine is installed, the

mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Door Mounting Accessories (Fig. 1-2-3-4-5).

Instructions for the fitter

Mounting the wooden panel onto the door and in-

serting the machine into cabinets:

In the case where the machine must be shipped for final

installation after the wooden panel has been mounted, we

suggest leaving it in its original packaging. The packaging

was designed to make it possible to mount the wooden

panel onto the machine without removing it completely (see

figures below).

The wooden panel that covers the face of the machine must

not be less than 18 mm in thickness and can be hinged on

either the right or left. For the sake of practicality when using

the machine, we recommend that the panel be hinged on

the same side as the door for the machine itself - the left.

N° 2 Hinge Supports

Fig. 1

N° 2 Hinges

Fig. 2

N° 1 Magnet

N° 1 Magnet plate

Fig. 4

Fig. 3

N° 1 Rubber plug

Fig. 5

N° 4 Spacers

Fig. 4/B

- No. 6 type A self-threading screws, l =13 mm.

- No. 2 type B metric, countersunk screws, l =25; for faste-

ning the magnet plate to the cabinet.

- No. 4 type C metric screws, l =15 mm; for mounting the

hinge supports to the cabinet.

- No. 4 type D metric screws, l =7 mm; for mounting the

hinges on the supports.

Mounting the Parts onto the Face of the Machine.

- Fit the hinge supports to the appliance front panel, positio-

ning the hole marked with an arrow in fig. 1 so that it is on the

inner side of the front panel. Fit a spacer (fig. 4/B) between

the surfaces using type C screws.

- Fit the magnet plate at the top of the opposite side, using

type B screws to fix two spacers (fig. 4/B) between the plate

and the surface.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Drilling Template.

- To trace the positions of the holes on the left-hand side of

the panel, align the drilling template to the top left side of the

panel using the lines traced on the extremities as a referen-

ce.

- To trace the positions of the holes on the right-hand side of

the panel, align the drilling template to the top right side of

the panel.

- Use an appropriately sized router to mill the holes for the

two hinges, the rubber plug and the magnet.

Fig. 8

Fig. 9

Accessories provided for the height adjustment.

The following can be found inside the polystyrene lid (fig. 10): 2

crossbars (G), 1 strip (M)

the following can be found inside

the appliance drum:

Mounding the Parts onto the Wooden Panel (Door).

- Insert the hinges into the holes (the movable part of the

hinge must be positioned facing away from the panel) and

fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the opposite side of

the hinges and fasten it with the two type B screws.

- Insert the rubber plug into the bottom hole.

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

The panel is now ready to be mounted onto the machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow in fig. 2)

into the hole for the hinge and push the panel towards the

front of the machine. Fasten the two hinges with the type D

screws.

2 plinth guides (Q)

Fig. 10

Adjusting the appliance height.

Fastening the plinth guide.

The height of the appliance can be adjusted (from 815 mm to

835 mm), by turning the 4 feet.

Should you require the appliance to be placed higher than the

above height, you need to use the following accessories to

raise it to up to 870 mm:

the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4

nuts (L) then perform the following operations (fig. 11):

remove the 4 original feet, place a crossbar G at the front of the

appliance, fastening it in place using screws I (screwing them in

where the original feet were) then insert the new feet H.

Repeat the same operation at the back of the appliance.

Now adjust feet H to raise or lower the appliance from 835 mm

to 870 mm.

If the machine is installed at the end of a set of modular ca-

binets, mount either one or both of the guides for the base

molding (as shown in fig. 8). Adjust them for depth based on

the position of the base molding, and, if necessary, fasten

the base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide Q into the

special slot and once it is in the desired position, lock it in

place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it with the

cabinets (fig. 6).

- Regulate the adjustable feet to raise the machine to the

appropriate height.

- To adjust the position of the wooden panel in both the

vertical and horizontal directions, use the C and D screws,

as shown in fig. 7.

Once you have reached the desired height, lock nuts L onto

crossbar G.

To adjust the appliance to a height between 870 mm and

900 mm, you need to mount strip M, adjusting feet H to the

required height.

Insert the strip as follows:

loosen the three screws N situated at the front of the Top cover

of the appliance, insert strip M as shown in fig. 12, then fasten

screws N.

Important: close the lower part of the appliance front by

ensuring that the plinth rests against the floor.

600 min

595

540

570

Fig. 11

Fig. 12

Fig. 6

Fig. 7

Download from Www.Somanuals.com. All Manuals Search And Download.

Care and maintenance

To access the pre-chamber:

Cutting off the water and electri-

city supplies

1. unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal;

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system in-

side the washing machine and help to prevent

leaks.

• Unplug the washing machine when cleaning

it and during all maintenance work.

Cleaning the washing machine

2. clean the inside thoroughly;

3. screw the lid back on;

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

Cleaning the detergent dispenser

drawer

Remove the dispenser

! Never use second-hand hoses.

by raising it and pul-

ling it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cle-

aning pump which does not require any main-

tenance. Sometimes, small items (such as

coins or buttons) may fall into the pre-chamber

which protects the pump, situated in its bot-

tom part.

! Make sure the wash cycle has finished and

unplug the appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions and tips

their local authority or retailer for information concerning the

correct disposal of their old appliance.

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Chil-

dren shall not play with the appliance. Clea-

ning and user maintenance shall not be made

by children without supervision.

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower

than the door opening; if it is not, remove excess water

using the drain hose, collecting it in a bucket as indicated

in the figure.

3. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

•Disposing of the packaging materials: observe local regu-

lations so that the packaging may be re-used.

•The European Directive 2012/19/EU on Waste Electrical

and Electronic Equipment, requires that old household

electrical appliances must not be disposed of in the normal

unsorted municipal waste stream. Old appliances must be

collected separately in order to optimise the recovery and

recycling of the materials they contain and reduce the im-

pact on human health and the environment. The crossed

out “wheeled bin” symbol on the product reminds you of

your obligation, that when you dispose of the appliance it

must be separately collected. Consumers should contact

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the washing machine

Control panel

ON/OFF

CHILD LOCK

button

SPIN SPEED

button

DISPLAY

MY CYCLE

button

WASH

CYCLE

SELECTOR

buttons

FUNCTION

buttons

START/PAUSE

DELAY

TIMER

button

Detergent dispenser drawer

button with

indicator light

TEMPERATURE

button

Detergent dispenser drawer: used to dispense deter-

gents and washing additives (see “Detergents and laundry”).

CHILD LOCK button: to activate the control panel lock,

press and hold the button for approximately 2 seconds.

When the symbol is illuminated, the control panel is locked

(apart from the ON/OFF button). This means it is possible

to prevent wash cycles from being modified accidentally,

especially where there are children in the home. To

deactivate the control panel lock, press and hold the

button for approximately 2 seconds.

ON/OFF button : press this briefly to switch the ma-

chine on or off. The START/PAUSE indicator light, which

flashes slowly in a green colour shows that the machine is

switched on. To switch off the washing machine during the

wash cycle, press and hold the button for approximately 2

seconds; if the button is pressed briefly or accidentally the

machine will not switch off. If the machine is switched off

during a wash cycle, this wash cycle will be cancelled.

DELAY TIMER button

: press to set a delayed start

time for the selected wash cycle. The delay time will be

shown on the display.

WASH CYCLE SELECTOR buttons: used to set the

desired wash cycle (see “Table of wash cycles”).

START/PAUSE button with indicator light: when the gre-

en indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has started the indicator light

will remain lit in a fixed manner. To pause the wash cycle,

press the button again; the indicator light will flash in an

MY CYCLE button: press and hold the button to store a

cycle with your own set of preferences in the memory of

the machine. To recall a previously stored cycle, press the

MY CYCLE button.

orange colour. If the symbol

is not illuminated, the door

may be opened. To start the wash cycle from the point at

which it was interrupted, press the button again.

FUNCTION buttons: press the button to select the

desired function. The corresponding indicator light on the

display will switch on.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

SPIN button : press to reduce or completely exclude

the spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease the tem-

perature: the value will be shown on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Display

The display is useful when programming the machine and provides a great deal of information.

The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-

tion relating to the progress status of the wash cycle.

String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the

time remaining until the start of the selected wash cycle.

String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include

a spin cycle, the string remains unused.

String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-

rature of the wash cycle cannot be modified, the string remains unused.

Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.

Door locked symbol

If the symbol is lit, this indicates that the washing machine door is locked to prevent it from being opened accidentally. To

prevent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.

N.B.: if the DELAYED START function has been activated, the door cannot be opened; pause the machine by pressing the

START/PAUSE button if you wish to open it.

Download from Www.Somanuals.com. All Manuals Search And Download.

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the On/Off

button ; the text HELLO will appear on the display

and the START/PAUSE indicator light will flash slowly in

a green colour.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol will be

on). During the wash cycle, the name of the phase in

progress will appear on the display. To change a wash

cycle while it is in progress, pause the washing machine

using the START/PAUSE button (the START/PAUSE

indicator light will flash slowly in an orange colour); then

select the desired cycle and press the START/PAUSE

button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press

the START/PAUSE button again to restart the wash

cycle from the point at which it was interrupted.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

3. MEASURE OUT THE DETERGENT. Open the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Press one of the WASH

CYCLE SELECTOR buttons to select the required wash

cycle; the name of the wash cycle will appear on the

display. A temperature and spin speed is set for each

wash cycle; these may be adjusted. The duration of the

cycle will appear on the display.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END OF CYCLE” on the display;

when the DOOR LOCKED

symbol switches off

the door may be opened. Open the door, unload the

laundry and switch off the machine.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

! If you wish to cancel a cycle which has already begun,

press and hold the

button. The cycle will be stopped

Modifying the temperature and/or spin

speed. The machine automatically selects the

maximum temperature and spin speed set for the

selected wash cycle; these values cannot therefore

be increased. The temperature can be decreased by

and the machine will switch off.

pressing the

setting is reached. The spin speed may be progressively

reduced by pressing the button, until it is completely

button, until the cold wash “OFF”

excluded (the “OFF” setting). If these buttons are

pressed again, the maximum values are restored.

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. When this

option is enabled, the

symbol lights up on the

display. To remove the delayed start function press the

button until the text “OFF” appears on the display.

Modifying the cycle settings.

• Press the button to enable the function; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the function; the

indicator light will switch off.

! If the selected function is not compatible with the

programmed wash cycle, the indicator light will flash

and the function will not be activated.

! If the selected function is not compatible with

another function which has been selected previously,

the indicator light corresponding to the first function

selected will flash and only the second function will

be activated; the indicator light corresponding to the

enabled function will remain lit.

! The functions may affect the recommended load value

and/or the duration of the cycle.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wash cycles and functions

Table of wash cycles

Detergents

Max. Max.

temp. speed

(°C) (rpm)

Description of the wash cycle

Fabric

softener

Wash

CLEAN Plus

Anti Stain

40° 1300



180’

White Cottons (1st press of the button): extremely soiled whites and resistant colours. 90° 1300

StandardCotton(1)(2ndpressofthebutton):heavilysoiledwhitesanddelicatecolours. 60° 1300

StandardCotton(1-2)(3rdpressofthebutton):lightlysoiledwhitesanddelicatecolours. 40° 1300

53 2,16 72 160’

53 1,10 52,5 190’

53 0,99 82 185’

Synthetics Resistant (1st press of the button): heavily soiled resistant colours. 60°

800



44 0,93 47 115’

44 0,57 46 100’

Synthetics Resistant (3) (1st press of the button): lightly soiled resistant colours.

40°

Synthetics Delicate (2nd press of the button): lightly soiled resistant colours.

75’

SPECIALS

Fast Wash (1st press of the button): to refresh normal soiled garments quickly

60° 1300

30° 800



3,5 53 0,81 40 60’

(not suitable for wool, silk and clothes which require washing by hand).

Fast Wash 30’ (2nd press of the button): to refresh lightly soiled garments quickly

(not suitable for wool, silk and clothes which require washing by hand).

71 0,15 35 30’

M My Cycle (Memory): allows for any wash cycle to be stored.

Anti Allergy

60° 1300



195’

EXTRAS

Wool (Woolmark Platinum): for wool, cashmere, etc.

40°

30°

800



1,5

70’

80’

16’

Delicates

Fast Spin Cottons (1st press of the button)

Rinse Cottons (2nd press of the button)

Pump out (3rd press of the button)

1300



36’

2’

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can

vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any

wash options selected.

For all Test Institutes:

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be

washed at 60°C and 40°C. The actual washing temperature may differ from the indicated value.

60°C (2nd press of the button); set wash cycle

40°C (3rd press of the button).

2) Long wash cycle for cottons: set wash cycle

40°C (3rd press of the button).

3) Long wash cycle for synthetics: set wash cycle 60°C (1st press of the button); temperature of 40°C (press TEMPERATURE button).

Wash functions

text “END OF CYCLE” will appear on the display.

To end the cycle, press the START/PAUSE button or the

“Reduced Creases” button.

Super Wash

Because a greater quantity of water is used in the initial

phase of the cycle, and because of the increased cycle

duration, this function offers a high-performance wash.

! It cannot be used with the

“Pump out”.

! It cannot be used with the , “Fast Wash 30’”,

, “Spin” and

Time Saver

If you select this option, the wash cycle duration will be

reduced by up to 50%, depending on the selected cycle,

thereby guaranteeing simultaneous water and energy

saving. Use this cycle for lightly soiled garments.

Extra rinse

By selecting this option, the efficiency of the rinse is increa-

sed and optimal residual detergent removal is guaranteed.

It is particularly useful for skin which is sensitive to deter-

gents. We recommend this option is used with a full load of

washing, or when a large amount of detergent is required.

! It cannot be used with the , “Fast Wash 60’”,

! It cannot be used with the “Fast Wash 30’”,

and “Pump out”.

, “Spin”

Eco Wash

The Eco Wash function saves energy by not heating the

water used to wash your laundry – an advantage both to

the environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage of

a liquid detergent.

Reduced Creases

By selecting this function, the wash and spin cycles will be

modified in order to reduce the formation of creases.

At the end of the cycle the washing machine will perform

slow rotations of the drum; the “Reduced Creases” and

START/PAUSE indicator lights will flash (orange) and the

! It cannot be used with the

Download from Www.Somanuals.com. All Manuals Search And Download.

Detergents and laundry

Detergent dispenser drawer

Special wash cycles

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessarily

result in a more efficient wash, and may in fact cause a

build up on the inside of your appliance and contribute to

environmental pollution.

! Use powder detergent for white cotton garments, for

pre-washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Anti Stain : this programme is suitable to heavily-soiled

garments with resistant colours. It ensures a washing

class that is higher than the standard class (A class). When

running the programme, do not mix garments of different

colours. We recommend the use of powder detergent.

Pre-treatment with special additives is recommended if

there are obstinate stains.

Anti Allergy: use programme

to remove major allergens

such as pollen, mites, cat’s and dog’s hair.

Wool: the wool wash cycle on this Hotpoint machine has

been tested and approved by The Woolmark Company

for washing wool garments labelled as hand washable

provided that the garments are washed according to the

instructions on the garment label and those issued by the

manufacturer of this washing machine. Hotpoint is the first

washing machine brand to be approved by The Woolmark

Company for Apparel Care- Platinum for its washing per-

formance and consumption of energy and water. (M1126)

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

In UK, Eire, Hong Kong and India the Woolmark trade

mark is a Certification trade mark.

!Do not pour detergent into the middle compartment (*).

Detergent should only be poured into the compartment 1.

Delicates: use programme

to wash very delicate

garments with decorative features, such as diamantes and

sequins.

We recommend turning the garments inside out before

washing and placing small items into the special bag

for washing delicates. Use liquid detergent on delicate

garments for best results.

compartment 1: Detergent for the wash cycle

(powder or liquid)

For best results liquid detergent should be poured in the

dispenser immediately before the start of the programme.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Load balancing system

Preparing the laundry

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load

is not balanced correctly, the machine spins at a reduced

spin speed. If the load is excessively unbalanced, the

washing machine performs the distribution process instead

of spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the

weight of the laundry when dry: see “Table of wash

cycles”.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem:

Possible causes / Solutions:

The machine does not switch on.

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

The wash cycle does not start.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• A delayed start has been set (see “Running a wash cycle”).

The machine does not fill with wa-

• The water inlet hose is kinked.

ter or “NO WATER CHECK SUPPLY” • The water inlet hose is not connected to the water supply.

appears on the display.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65

water and continually drains away

or Water left in the drum

or Stuck on wash.

and 100 cm from the floor (see “Installation”).

• The drain hose is connected incorrectly to the sink trap allowing water to run

into the machine, the drain hose must be positioned higher than the bottom of

the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

The machine does not drain or spin • The Pump filter is blocked.

or F05 error code in the display.

• The drain hose is kinked (see “Installation”).

• New Installation - The blanking cap or spigot has not been removed if con-

nected under a sink.

• The drain hose or sink trap is blocked.

• The wash cycle does not include draining, some wash cycles require the drain

phase to be started manually.

• The REDUCED CREASES function button has been activated. To complete the

wash cycle, press the START/PAUSE button (see “Wash cycles and functions”).

• The ‘Spin Speed’ selector knob is in the “OFF” position.

The machine does not heat or poor • The ‘Temperature’ selector knob is in the “OFF” position.

wash results.

The programme takes too long

or The Display changes the estima-

ted ‘Time to End’ during the pro-

gramme.

• Programme times will vary due to water pressure, the incoming water tempera-

ture and if the wash load goes out of balance. This will increase the programme

times accordingly (see ‘ The machine wont spin properly’ below).

The machine vibrates a lot during

the spin cycle.

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at

a lower speed.

Download from Www.Somanuals.com. All Manuals Search And Download.

The machine is noisy.

• There will always be some motor, pump and drum noise during spin.

The machine wont spin properly.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the load

required before the machine will go into higher spin speeds - This will increase

the programme time accordingly. This is a safety feature to prevent damage.

Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,

etc). - Try the programme again using a different load.

The machine leaks from the di-

spenser.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down the tap

on the water supply pipe slightly and try again.

• The machine is tilting forwards - It must be level when in its final position.

The machine leaks (other than

dispenser).

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill

hose is missing the rubber washer.

• The drain hose is not fixed in properly.

The indicator lights on the console

are flashing rapidly.

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again If the problem persists contact the Technical Assistance

Service.

The machine smells.

• The machine requires a service wash. Run a 90 degree wash cycle with deter-

gent and no laundry.

The machine door cannot be

opened.

• The door will not open until the door lock indicator light goes out shortly after

the program has finished.

Door Seal damaged at the bottom.

• The door seal has drainage holes at the bottom - This is normal.

• The water level is correct if it can be seen at the bottom of the door.

The water level is too low when

the machine is washing.

There is too much foam.

• The detergent is not suitable for machine washing (it should display the text

‘for washing machines’ or ‘hand and machine wash’ or the like).

• Too much detergent was used - less detergent is required in soft water.

After completing the programme,

or before starting a programme,

the machine has turned itself off

(no lights).

• To comply with new energy saving regulations the machine is fitted with an

automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate

the machine, it can then either be switched off or a new programme selected.

General.

• Your washing machine contains sensors that monitor progress during the wash

cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-

gress).

Normally, if your machine successfully completes the cycle, there is unlikely to

be anything wrong!

Remember, you will be charged for a service call for problems caused by incorrect installation, as listed

above.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine

washable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Assistance

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

Download from Www.Somanuals.com. All Manuals Search And Download.

195117174.00

09/2013

Xerox Fabriano

Download from Www.Somanuals.com. All Manuals Search And Download.

Hamilton Beach Slow Cooker 840149600 User Manual
Harman Kardon CD Player HD710 User Manual
Harman Stove Company Stove TLC 2000 Stove User Manual
Havis Shields Indoor Furnishings C TCB 5 User Manual
Hearth and Home Technologies Indoor Fireplace SILH60EV User Manual
Heath Zenith Door 598 1143 01 User Manual
Hughes Kettner Stereo Amplifier Mark II 100W Head User Manual
Husqvarna Chainsaw 1150901 95 User Manual
iLive Music Mixer AP7141 User Manual
Impex Home Gym TSA 5682 User Manual