Instructions for Installation and Use
Gas Hob
Models GD74, GD74 CH,GD64, GF740, GE740TCX
To the Installer
Before installation fill in the product details on the back cover of this book.
The information can be found on the rating plate.
To the User
You must read the instructions prior to installing and using the appliance and
then retain them for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Your new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been
installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The hob is designed specifically for domestic use and responsibility will not be accepted for use in any other installation.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with this booklet.
(b) Has been properly connected to a suitable supply voltage as stated on the rating plate, attached to the
appliance.
(c) Has not been subjected to misuse or accident or been modified or repaired by any person other than the
manufacturers authorised employee or agent.
(d) Has been correctly installed.
This appliance conforms with the following European Economic Community directives:
-
-
-
-
73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;
89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications;
90/396/EEC of 29/06/90 (Gas) and subsequent modifications;
93/68/EEC of 22/07/93 and subsequent modifications.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
For Your Safety
When used properly your appliance is completely safe but as with any electrical product there are certain
precautions that must be observed.
PLEASE READ THE BELOW PRECAUTIONS BEFORE USING YOUR APPLIANCE.
To maintain the efficiency and safety of this appliance, we recommend you do the following:
- only call the Service Centres authorised by the manufacturer.
- always use genuine spare parts.
ALWAYS:
NEVER:
- make sure you remove all packaging and dispose of safely. - attempt to install or repair the appliance without the
- check the soundness of the appliance after it has been assistance of qualified personnel.
unpacked.
- store items above the appliance that children may attempt
- make sure you understand the controls before using the to reach.
appliance.
- heat up unopened food containers, as pressure can build
up causing the container to burst.
- keep children away from the appliance during use.
- take care to avoid heat/steam burns when operating the - use the appliance to heat up anything other than food.
controls. - use the appliance as a room heater.
- make sure the controls are turned off when you have finished - dry any items on the hob.
cooking and when not in use.
- install the appliance next to curtains or other soft furnishings.
- take care to avoid heat/steam burns when operating the - allow children to play with or tamper with the controls.
controls.
-leave children unsupervised where cooking appliances are
- disconnect from the power supply, and allow to cool, before installed as all the cooking surfaces get hot during and after
cleaning or performing maintenance.
use.
- refer servicing to a qualified appliance service engineer.
- store chemicals, foodstuffs or pressurised containers in or
- keep the hob clean as a build up of grease or fat from on the appliance, or in cabinets immediately above or next
cooking can cause a fire. to the appliance.
- follow the basic principles of food handling and hygiene to - use flammable or plastic items on or near the hob.
prevent the possibility of bacterial growth. - use adapters, multiple sockets and/or extension leads.
- dry food thoroughly before frying and lower it slowly into the - fill a deep fat frying pan more than 1/3 full of oil, or use a lid.
hot oil or fat. Frozen food in particular, will cause frothing and DO NOT LEAVE UNATTENDED WHILE COOKING.
spitting if added too quickly.
- keep outside of pans clean and free from streaks of oil or only lowers the temperature or the oil or fat too much, resulting
fat. in greasy food.
- fry too much food at a time, especially frozen food. This
- place pans centrally over the burner making sure handles - pull on the appliance or the supply able to unplug it from
are kept away from the edge of the hob and cannot be the electrical outlet.
heated by other burners/pans.
- keep any ventilation slots clear of obstructions.
- allow power cables of other appliances to come into contact.
- with hot parts of this appliance.
- expose the appliance to atmospheric agents, such as
rain or sunlight.
- operate the appliance with wet hands.
- allow anyone to sit or stand on any part of the appliance.
- use misshapen pans which may be unstable.
- use round base woks directly on the pan supports.
- use fish kettles or large preserving pans across two burners.
- operate the appliance with wet parts of the body.
- operate the appliance when barefoot.
SAFETY ADVICE
IMPORTANT - As with any cooking appliance there could be some fire risk attached to the heating of oil, particularly for
deep fat frying. Cooking utensils containing oil must not be left unattended (eg. to answer the telephone) on or in close
proximity to the cooking areas.
IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:
1. Turn off the burners.
2. Cover the pan with a fire blanket or damp cloth, this will smother the flames and extinguish the fire.
3. Leave the pan to cool for at least 60 minutes before moving it. Injuries are often caused by picking up a hot pan and
rushing outside with it.
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of the extinguisher is likely to tip the pan
over. Never use water to extinguish oil or fat fires.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Know your Hob
Model GD74, GD74 CH
A
TC
F
RR
B
S
C
D
Model GF740, GE740TCX
Model GD64
S
A
S
A
RR
S
B
R
S
B
C
C
B. Pan Support for Cookware
C. Control Knobs for Gas Burners
D. Ignitor for Gas Burners
F. Flame Failure Device - Activates if the flame accidentally
goes out (spills, drafts, etc.), interrupting the delivery of
gas to the burner.
A.
R
S.
Auxilliary Burner
Rapid Burner
Semi Rapid Burner
RR. Reduced Rapid Burner
TC. Triple Crown Burner (Wok Burner)
How To Use Your Hob
The position of the corresponding gas burner is indicated on
each control knob.
To light a burner, simply press the corresponding knob all
the way in and then turn it in the counter-clockwise direction
to the "High" setting, keeping it pressed in until the burner
lights.
The burners differ in size and power. Choose the most
appropriate one for the diameter of the cookware being used.
The burner can be regulated with the corresonding control
knob by using one of the following settings:
• Off
Caution: If the burner accidently goes out, turn off the gas
with the control knob and try to light it again after waiting at
least 1 minute.
These models are fitted with a safety device (F), the
knob must be pressed in for about 6 seconds until the device
that keeps the flame lighted warms up.
High
Low
To turn off a burner, turn the knob in the clockwise direction
until it stops (it should be on the “•” setting).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Practical Advice
Practical Advise on Using the Burners
For best performance, follow these general guidelines:
Burner
Cookware Diameter
(cm)
•
Use the appropriate cookware for each burner (see
table) in order to prevent the flame from reaching the
sides of the pot or pan;
Alwasy use cookware with a flat bottom and keep the
lid on;
Rapid (R)
24 - 26
22 - 24
16 - 20
10 - 14
Reduced Rapid (RR)
Semi-Rapid (S)
Auxilliary (A)
•
•
Triple Crown (TC)
24 - 26
When the contents come to a boil, turn the knob to
"Low".
To identify the type of burner, refer to the 'Burner and Nozzle
Specifications' section.
Care and Cleaning
Before cleaning or performing maintenance on your hob,
disconnect it from the power supply.
To extend the life of the hob, it should be cleaned
carefully and thoroughly on a frequent basis, keeping in
mind the following:
Greasing the Gas Valves
Over time, the gas valves may stick or become difficult to
turn. If this is the case, the must be cleaned on the inside
and the regreased.
N.B.: This procedure must be performed by a technician
authorized by the manufacturer.
•
•
•
•
•
The enamelled parts must be washed with warm water
without using abrasive powders or corrosive substances
which could ruin them.
The removable parts of the burners should be washed
frequently with warm water and soap, making sure to
remove caked-on substances.
On hobs with automatic ignition, the end of the electronic
ignition device must be cleaned carefully and frequently,
making sure that the gas holes are not clogged.
The top must be cleaned with glass cleaning products.
Avoid using abrasive products and abrasive sponges
that could scratch the glass.
The glass surfaces should be cleaned regularly with a
solution of warm water and a non-abrasive detergent.
First, remove all food build up or grease with a cleaning
scraper (Fig.A).
Fig. A
diffuser,
Do not place anything, e.g.
asbestos mat, between pan and pan
support as serious damage to the
appliance may result.
•
Stainless steel can be stained if it remains in contact
with highly calcareous water or aggressive detergents
(containing phosphorous) for an extended period of time.
It is recommended that these parts be rinsed thoroughly
with water and then dried well. It is also a good idea to
clean up any spills.
Do not remove the pan support and
enclose the burner with a work stand as
this will concentrate and deflect the heat
onto the hotplate.
Clean the cooking surface when it is still warm with a
suitable cleaning product, rub with a clean damp cloth
and dry. Sugar or foods with a high sugar content that
have melted onto the surface must be removed
immediately with a scraper while the surfacr is still hot. DO
NOT use abrasive sponges or cleaning products under
any circumstances. This holds true for chemically
Do not use large pots or heavy weights
which can bend the pan support or
deflect the flame onto the hotplate.
aggressive cleaners, like oven sprays and stain removers.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before calling service for assistance, check through the
If the burner does not remain on when set to "Low".
following list, there may be nothing wrong.
Check to make sure that:
First of all, check to see that there are no interruptions in the
gas and electrical supplies, and, in particular, that the gas
valves for the mains are open.
•
•
•
The gas holes are not clogged.
There are no draughts near the cooking surface.
The minimum has been adjusted correctly (see Installation
section, "Minimum Regulation").
If the burner does not light or the flame is not uniform
around the burner.
If the cookware is not stable.
Check to make sure that:
Check to make sure that:
•
•
The gas holes on the burner are not clogged.
All of the movable parts that make up the burner are
mounted correctly.
•
•
•
The bottom of the cookware is perfectly flat.
The cookware is centered correctly on the burner .
The support grids have not been inverted.
•
There are no draughts around the cooking surface.
If, despite all of these checks, the hob does not function
properly and problem persists, call Hotpoint Service (see
KEY CONTACTS, back page), informing them of:
- The type of problem.
- The abbreviation used to identify the model (Mod. ...) as
indicated on the warranty.
If the flame does not stay lit on a model with the
Flame Failure device.
Check to make sure that:
•
•
You press the knob all the way in.
You keep the knob pressed in long enough to activate
the flame failure device.
•
The gas holes are not clogged in the area corresponding
to the flame failure device.
IMPORTANT:
Never call upon technicians not authorized by the
manufacturer, and refuse to accept spare parts that are not
original.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Thefollowinginstructionsareintendedfortheinstallersothatthe
d) Liquidifiedpetroleumgasesareheavierthanairand,asaresult,
settle downwards. Rooms in which LPG tanks are installed
mustbefittedwithventilationopeningstotheoutsideinorderto
allowthegastoescapeintheeventofaleak. Therefore, LPG
tanks, whether empty or partially full, must not be installed or
storedinroomsorspacesbelowgroundlevel(cellars,ect.).Itis
alsoagoodideatokeeponlythetankcurrentlybeingusedin
theroom,makingsurethatitisnotnearsourcesofheat(ovens,
fireplaces,stoves,etc.)thatcouldraisetheinternaltemperature
of the tank above 50°C.
installationandmaintenanceproceduresmaybefollowedinthe
most professional and expert manner possible. Important:
Disconnect the appliance from the electrical supply before
performinganymaintenanceorrepair.
PositioningtheHob
Important: this unit may be installed and used only in
permanently ventilated rooms in accordance with British
Standard Codes Of Practice:B.S. 6172 / B.S. 5440, Par. 2 and
B.S.6891 Current Editions.The following requirements must be
observed:
InstallationofBuilt-inHobs
The gas hob is equipped with type X degree protection against
overheating. Therefore, the appliance can be installed next to
cabinets,providedtheheightofthecabinetdoesnotexceedthatof
thehob. Forproperinstallationofthehob, thefollowingguidlines
mustbefollowed:
a) Theroommustbefittedwithaventilationsystemwhichvents
smokeandgasesfromcombustiontotheoutside.Thismust
be done by means of a hood or electric ventilator that turns
onautomaticallyeachtimethehobisoperated.
a) Ifthecabinet(s)locatednexttothehobarehigherthanthehob
itself, thecabinet(s)mustbeinstalledatleast110mmfromthe
hobedge.
b) Hoods must be installed in accordance with the instructions
containedintheinstallationmanualforthehoodsthemselves,
andnolessthan650mmfromthehob.
c) In the case of the 600 mm cooker hoods, besides following
the recommendations in point b), the cabinets should be
positioned next to the hood at a height of at least 540 mm
from the top since this will make it possible to install the lid
and move it correctly.The cabinet should always be installed
at a height from the top which allows easy use of pots and
pans on the cooker.
d) Shouldthehobbeinstalleddirectlyunderacupboard,thelatter
shouldbeatleast700mm(millimetres)fromthetop,asshown
inFigureC.
In a chimney stack or branched flue.
(exclusively for cooking appliances)
Directly to the Outside
b) Theroommusthaveanairflowtoallowforpropercombustion.
3
Thismustbe2m ³/hperkWofinstalledpower.Theairflowcan
HOOD
Fig. C
becreatedusinganenclosedventwithaninnercrosssection
ofatleast100cm²whichmustnotbeabletobeblocked. Ithe
appliancedoesnothaveaflamefailuredevice, theventmust
Min. 600mm.
3
haveaninternalcrosssectionof200cm ³(Fig.A). Alternatively
theroominwhichthehobissituatedcanbeventedindirectly
through ventilation ducts as specified above, as long as the
adjacentroomisnotasharedarea, abedroomorpresentany
riskoffire(Fig.B).
Detail A
Adjacent
Room
Room to be
Vented
e) Thedimensionsofthecutoutfortheappliancemustbethose
indicatedinthefigureD.Clampsareprovidedtofastenthehob
tocountersmeasuringfrom20to40mminthickness.Tofasten
the hob securely, it is recommended that all the clamps be
used.
Fig. D
A
555 mm.
Examples of ventilation holes
for comburant air.
Enlarging the ventilation slot
between window and floor.
Fig.A
Fig.B
c) Intensiveandprolongeduseoftheappliancemaynecessitate
supplementalventilation, e.g. openingawindoworincreasing
thepoweroftheairintakesystem(ifpresent).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Before fastening the hob in place, position the seal
(supplied) along the perimeter of the worktop, as shown
in the figure.
When installing the hob above a built-in oven without forced
ventilation,ensurethatthereareairinletsandoutletsforventilating
theinteriorofthecabinetadequately.
Clamps are provided to fasten the hob to counters
measuring from 20 to 40 mm in thickness. To fasten the
hob securely, it is recommended that all the clamps be
used.
Gas Connection for the Hob
Thehobshouldbeconnectedtothegassupplybyanauthorized
installer. During installation of this product it is essential to fit an
approvedgastaptoisolatethesupplyfromtheapplianceforthe
convenienceofanysubsequentremovalorservicing.Connection
of the appliance to the gas mains or liquid gas tanks must be
carriedoutaccordingtothesafetystandardscurrentlyinforce,and
onlyafteritisascertainedthatitissuitableforthetypeofgastobe
used. Ifnot, followtheinstructionsindicatedinthesectionentitled,
“Adapting the Hob for Different Types of Gas”. If the hob is to be
connectedtotankscontainingliquidgas, usepressureregulators
thatcomplywithcurrentsafetystandards.
Fastening Clamps - Assembly Diagram
Important: Toinsurethattheapplianceoperatessafety, thegas
is regulated correctly and your appliance lasts over time, make
surethatgaspressurelevelscomplywiththeindicationsgivenin
Table1, “NozzleandBurnerSpecifications”.
Clamp Position for
H=30mm top
Clamp Position for
H=40mm top
Front
Gas Connection to Non-flexible Pipe
(copper or steel)
Connection to the gas source must be done in such a way as to
not create any stress points at any part of the appliance.
The appliance is fitted with an adjustable, "L" shaped connector
and a gasket for the attachment to the gas supply. Should this
connector have to be turned, the gasket must be replaced
(supplied with the appliance).
Thegasfeedconnectortotheapplianceisathreaded, male 1/2"
connectorforroundgaspipe.
Clamp Position for
H=20mm top
Back
Gas Connection to Flexible Steel Pipe
N.B: Use the clamps contained in the "accessory kit."
f) In the event the hob is not installed above a built-in oven, a
woodpanelmustbeinsertedasinsulation. Thispanelmustbe
placedatleast20mmfromthebottomofthehobitself.
Important:Wheninstallingthehobaboveabuilt-inoven,theoven
should be placed on two wooden strips; in the case of a joining
cabinet surface, remember to leave a space of at least 45 x 560
mmattheback.
Thegasfeedconnectortotheapplianceisathreaded, male1/2"
connectorforroundgaspipe. Onlyusepipes, tubesandgaskets
thatcomplywithcurrentsafetycodes. Themaximumlengthofthe
flexible pipes must not exceed 2000 mm. Once the connection
hasbeenmade,ensurethattheflexiblemetaltubedoesnottouch
anymovingpartsandisnotcrushed.
Check the Seal
Once the hob has been installed, make sure all the connections
are properly sealed, using a soapy water solution. Never use a
flame.
560 mm.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Adapting the Hob for Different Types of Gas
RegulationofAirSupplytotheBurner
To adapt the hob to a different type of gas than that for which it
wasdesigned,(seethestickerunderthehoboronthepackaging),
theburnernozzlesmustbechanged, asfollows:
Theburnersdonotneedaprimaryairregulator.
MinimumRegulation
• Turn the gas valve to minimum.
• Remove the pan supports and slide the burners out of the
•
Remove the knob and turn the regulator screw (positioned
either on the side of the top or inside the shaft) clockwise
untiltheflamebecomessmallbutregular.
cooktop.
• Unscrew the nozzles using a 7mm socket wrench and
replacethemwiththoseforthenewtypeofgas. (Seetable1,
“BurnerandNozzleSpecifications”).
N.B.: In the case of liquid gas, the regulation screw must be
fully screwed in (clockwise).
• Reassemblethepartsfollowingtheinstructionsinreverseorder.
• Oncompletingtheoperation, replacetheoldratinglabelwith
the one showing the new type of gas; the sticker is available
fromHotpointService(seeKEYCONTACTS, backpage).
If the gas pressure is different than that prescribed, a pressure
regulatormustbeinstalledatthesource,incompliancewithnational
standardsgoverningtheuseof pipedgasregulators.
• Makesurethat,whentheknobisturnedrapidlyhightolow,the
flamedoesnotgoout.
• In the event of a malfunction on appliances with the security
device(thermocouple)whenthegassupplyissetatminimum,
increasetheminimumsupplylevelsusingtheregulatorscrew.
Once the adjustment has been made, apply sealing wax, or a
suitable substitute, to the old seals on the by-pass.
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Before connecting to the power supply, make sure that:
Electrical connection
• the limiter switch and the domestic system can
withstand the load from the appliance (see rating
plate).
• the supply system is efficiently earthed according to
standards and laws in force.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The hob is designed to work with alternating current, the
supply voltage and frequency indicated on the rating plate
(situated under the hob). Make sure that the local supply
voltage corresponds to the voltage indicated on the rating
plate.
• the socket or double-pole switch are easily accessible
when the appliance is installed.
Connecting the supply cable to the mains electricity
supply
Important: the wires in the mains lead are coloured in
accordance with the following code:
For models supplied without a plug, fit a standard plug
suitable for the load indicated on the rating plate, onto a
cable and connect to a suitable socket.
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
To connect direct to the mains supply, a double pole switch
with a contact separation of at least 3mm suitable for the
load and complying with current standards and regulations
must be fitted between the appliance and the mains supply
outlet.
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
Connect the Green & Yellow wire to terminal marked “E” or
or coloured Green or Green & Yellow.
Connect the Brown wire to the terminal marked “L” or coloured
Red or Brown.
Connect the Blue wire to the terminal marked “N” or coloured
Black or Blue.
The green-yellow earth wire must not be interrupted by the
switch.
The supply cable must be positioned so that no part of it
reaches a temperature of 50°C above room temperature.
For installation above a built-under oven, the hob and the
oven must be connected separately to the electricity supply,
both for safetly reasons and for easy removal of the oven
for repair, maintenance etc.
FAILURE TO OBSERVE THE ACCIDENT-
PREVENTION REGULATIONS RELIEVES THE
MANUFACTURER OF ALL LIABILITY.
DO NOT use adapters as they could cause overheating or
burning.
Replacing the cable
Use a rubber cable of the type H05RR-F with a suitable
cross section 3 x 0.75 mm².
The yellow-green earth wire must be 2-3 cm longer than
the other wires.
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Characteristic of the burners and nozzles
Table 1
Liquid Gas
Natural Gas
Burner
Diameter Thermal Power
By-pass
1/100
Nozzle
1/100
Flow*
g/h
Nozzler
1/100
Flow*
l/h
(mm)
kW (p.c.s.*)
(mm)
Nom. Red.
(1)
(mm)
86
***
**
(mm)
116
Rapid
(Large) (R)
100
100
75
3.00
2.60
1.65
1.00
3.25
0.7
0.70
0.4
41
41
30
30
60
39
39
28
28
57
218
214
186
118
71
286
248
157
95
Reduced
Rapid (RR)
80
64
50
91
189
120
73
110
96
Semi Rapid
(Medium) (S)
Auxiliary
(Small) (A)
55
0.4
71
Triple Crown
(TC)
130
1.3
236
232
133
309
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
Supply
pressures
*
At 15°C and 1013 mbar-dry gas
Natural
P.C.S. = 37.78 MJ/m3
**
Propane
P.C.S. = 50.37 MJ/kg.
P.C.S. = 49.47 MJ/kg.
(1) re. Models with the security device (Ref. F).
*** Butane
1 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
"No company is better positioned to offer an after sales service on a
Hotpoint appliance than us - the manufacturer"
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts
and labour guarantee for the first 12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales
service options:
Repair Service and Information Help Desk
UK: 08709 066066
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number of your appliance
Available 364 days a year with a fast, effective and value for money service. We have the largest white
goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts
and labour guarantee for 12 months from the date of the repair.
If you require any information or have any questions about your appliance, our operators are on hand with
help and advice.
All this ensures that you will receive the best available after sales service possible.
Extended Warranties
UK: 08709 088 088
Republic of Ireland: 1850 502 200
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover
plans to give you total peace of mind.
l Repair Protection Plan
-
FREE service repairs for a single Hotpoint appliance during the period
of cover.
l Kitchen Cover
-
FREE service repairs for all your Hotpoint appliances less than 8
years old.
Genuine Parts and AccessoriesUK: 08709 077 077
Republic of Ireland: (01) 842 6836
A wide range of genuine parts and accessories are available from our hotline or through our web site.
Genuine parts and accessories, extended warranties and service repairs are all
available on our web-site at:
GB
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
"Satisfaction guaranteed or your money back"
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or
engineer to call. If the technical problem is not resolved under this guarantee, we will replace your
machine or, if you prefer, give you your money back.
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free
replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker
hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.
Guarantee terms and conditions
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the
following provisions that your appliance:
l
l
Has been installed and used correctly in accordance with this instruction booklet.
Has been used solely for domestic purposes and is located on domestic premises (ie. not for
commercial or trade use).
l
l
Has been properly connected to a suitable electrical supply voltage as stated on the appliance
rating plate.
Has not been subject to misuse, accident, modified or repaired by anyone other than one of our
own service engineers.
For pre purchase information on any other Hotpoint product call: 08701 50 60 70
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the plug and cut mains cable off flush with the appliance.
Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains
socket.
GB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Contacts
After Sales Service
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in
both the appliances and services we offer.
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number:
Serial number:
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
Republic of Ireland: (01) 842 6836
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.
02/2005 - 195036406.03
Download from Www.Somanuals.com. All Manuals Search And Download.
|