IS4813 / IS4815 / IS4823 / IS4825
Single-Line Laser Scan Engine
Integration Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Grounding....................................................................................................................................................1
Thermal Considerations...............................................................................................................................1
Airborne Contaminants and Foreign Materials............................................................................................. 1
Laser Safety ................................................................................................................................................1
Product Overview ........................................................................................................................................2
Non-Decode Engines.............................................................................................................................3
Decode Engines.....................................................................................................................................3
Labels..........................................................................................................................................................3
IS4813 and IS4815 Non-Decode Engine................................................................................................4
IS4823 and IS4825 (-0) Decode Engine Assembly ................................................................................4
IS4823 and IS4825 Bracketed (-1) Decode Engine Assembly................................................................5
Exit Beam Specifications .............................................................................................................................9
Electrostatic Discharge (ESD) Cautions...............................................................................................11
Grounding............................................................................................................................................11
Power Supply.......................................................................................................................................11
Power Sequencing...............................................................................................................................11
Host Flex Cable ...................................................................................................................................12
Thermal Considerations.......................................................................................................................12
Printed Circuit Board Component Clearance........................................................................................12
Magnetic Sensitivity .............................................................................................................................12
Airborne Contaminants and Foreign Materials .....................................................................................12
Exit Laser Beam Clearance..................................................................................................................13
Return Aperture Clearance ..................................................................................................................13
Output Window Properties ...................................................................................................................13
Output Window Coatings .....................................................................................................................14
Output Window Angle ..........................................................................................................................14
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup Condition Timing Diagram............................................................................................................. 18
Common Activation Mode Features........................................................................................................... 20
Sleep Mode ...............................................................................................................................................21
Serial Configuration Mode............................................................................................................................ 22
Operational................................................................................................................................................24
Mechanical ................................................................................................................................................24
Electrical....................................................................................................................................................25
Environmental............................................................................................................................................25
Limited Warranty ...........................................................................................................................................38
Index...............................................................................................................................................................39
Technical Assistance................................................................................................................................. 41
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Getting Started*
Note:
THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040. USE ONLY AS A COMPONENT.
integrating an IS4800 series scan engine into a system.
Electrostatic Discharge (ESD) Cautions
ESD has the ability to modify the electrical characteristics of a semiconductor device, possibly
degrading or even destroying the device. ESD also has the potential to upset the normal
operation of an electronic system, causing equipment malfunction or failure.
The scan engine has exposed electrical components.
•
•
•
DO NOT touch the leads of the visible laser diode (VLD) or other components.
ALWAYS use grounding wrist straps and a grounded work area when handling the engine.
Mount the engine in a housing that is designed for ESD protection and stray electric fields.
Grounding
If the scan engine is to be installed in a grounded host:
•
•
The die-cast engine chassis is at +Vcc. Use an insulator between the engine chassis and host.
Use non-metallic nylon or equivalent screws.
Thermal Considerations
The IS4800 laser scan engine series is qualified over the specified operational temperatures (0°C to 40°C) for
all operating modes. Make sure ambient temperatures do not exceed this range in order to obtain optimal
operation. Operating the IS4800 in continuous mode for an extended period may produce considerable
heating. This mode should be limited and sufficient airflow should be provided whenever possible to minimize
internal heating. Excessive heating may potentially damage the IS4800 engine.
Airborne Contaminants and Foreign Materials
The scan engine has very sensitive miniature electrical and optical components that must be protected from
airborne contaminants and foreign materials. In order to prevent permanently damaging the scan engine and
•
Sealed to prevent infiltration by airborne contaminants and foreign materials such as dust, dirt, smoke,
and smog.
•
Sealed to protect against water, humidity and be non-condensing.
Laser Safety
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Product Overview
The IS48xx series are miniature laser scan engines. The non-decode IS4813 and IS4815 laser scan engines
are designed for direct integration into custom OEM devices equipped with a decoder. The engine’s small size
is ideal for integration into mobile computers, hand-held scanners, medical/diagnostic equipment, mobile
printers, lottery terminals, ATMs and access control devices.
For customer applications requiring integrated decode functionality in addition to solid scan engine
performance, the IS4823 and IS4825 models combine the miniature IS4813 and IS4815 engines with a
decoder and an optional mounting bracket for a complete small package that provides integration flexibility to
meet a variety of OEM applications.
The IS4813 and IS4815 deliver aggressive scanning with a digitized bar/space signal output. The IS4823 and
IS4825 provides a decoded output on all standard 1D bar code symbologies — including UPC, EAN, Code 39
and I 2 of 5 — as dense as 4 mil. The IS4823 and IS4825 models support TTL level RS232 or USB system
interface. They can operate in standard trigger mode, as well as “blinky” mode for hands-free scanning.
The IS48xx series is equipped with a multitude of features including:
•
•
•
•
•
•
•
100 scan lines per second
Support for 3.3VDC input voltage (IS4813, IS4823)
Support for 5VDC input voltage (IS4815, IS4825)
A 650 nm bright laser diode
A rugged die cast engine chassis with threaded mounting holes
An optional mounting bracket for integration flexibility (IS4823, IS4825)
A 10-pin (IS4813, IS4815) or 12-pin (IS4823, IS4825) ZIF connector with industry standard pinout for
seamless integration into portable devices
•
•
A wide sweep angle for scanning larger bar codes up close
For ease of integration and optimum engine performance, a Software Development Kit (SDK) for the IS4813
and the IS4815 is available. Contact a customer service representative or sales representative for additional
information (see page 41).
Important Notes:
•
The manufacturer of the end equipment must register with agencies such as the Food and Drug
Administration (FDA). The specifications required for registration are not obtainable until the OEM
manufacturer uses the IS4800 series scan engine in its final configuration. Therefore, it becomes the
responsibility of the manufacturer who incorporates the scan engine into their product to comply with all
federal laser safety regulations. The manufacturer must submit a Laser Product Report for the FDA in
the US.
•
THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040. USE ONLY AS A COMPONENT.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Models and Accessories
Non-Decode Engines
Model
Options
Description
IS4813
IS4815
Non-Decode, 3.3VDC Scan Engine
Non-Decode, 5VDC Scan Engine
Accessories
Part Number
19-00358
Description
Flex Cable, 10-POS, 67.5 mm Length
Decode Engines
Options
Base Model
IS4823
Description
3.3VDC Scan Engine with Decode PCB
5VDC Scan Engine with Decode PCB
IS4825
Model and Kit Delineation
Figure 1. IS4823/IS4825 Model and Kit Delineation
Accessories
Description
Part Number
19-00329
Flex Cable, 12-POS, 80 mm Length
Flex Cable, 10-POS, 67.5 mm Length
19-00358
Labels
Figure 2. Serial Number Label (Enlarged For Illustration Purposes)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Components of the IS4800 Engine Series
IS4813 and IS4815 Non-Decode Engine
Item
Description
Item Location
1
2
Exit Beam Location, Laser Light Aperture
3
AVOID EXPOSURE! – LASER LIGHT IS
EMITTED FROM THIS APERTURE.
4
5
6
7
Flex Cable, 10-POS
ZIF Connector, 10-Pin
Printed Circuit Board and Shield
Die Cast Chassis
Figure 3. IS4813/IS4815
IS4823 and IS4825 (-0) Decode Engine Assembly
Item
Description
Decode Printed Circuit Board
ZIF Connector, 12-PIN
Item Location
1
2
3
4
5
Flex Cable, 12-POS
IS4813 or IS4815 Laser Scan Engine
Exit Beam Location, Laser Light Aperture
6
AVOID EXPOSURE! – LASER LIGHT IS
EMITTED FROM THIS APERTURE.
7
8
Figure 4. IS4823-0/IS4825-0
Flex Cable, 10-POS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IS4823 and IS4825 Bracketed (-1) Decode Engine Assembly
Item
Description
Item Location
1
Flex Cable, 12-POS
2
3
Flex Cable, 10-POS
ZIF Connector, 10-PIN
Exit Beam Location, Laser Light Aperture
AVOID EXPOSURE! – LASER
LIGHT IS EMITTED FROM THIS
APERTURE
4
5
6
IS4813 or IS4815 Laser Scan Engine
ZIF Connector, 12-PIN
7
Decode Printed Circuit Board
Figure 5. IS4823-1/IS4825-1 Assembled
0.10 Dia. Clearance Holes for Mounting,
2 Pls.
8
M2 x 0.4 Threaded Bosses for Mounting,
3 Pls.
9
10
Bracket
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Specifications
IS4813 and IS4815 Scan Engine Dimensions
The engine has two M1.6 tapped holes on the bottom of the chassis for mounting the engine with screws.
Two additional blind holes are provided on the bottom of the engine for keying purposes to assist with engine
alignment (see figure below).
Warning: The limited warranty (on page 38) is void if the following recommendations are not adhered to when
mounting the IS4800 series laser scan engine.
Follow the guidelines listed below when securing the engine to non-metallic or metallic mounting surfaces.
For a non-metallic mounting surface:
•
•
•
•
Use non-magnetic M1.6 x .35 stainless steel screws.
Do not exceed 1.35 ± .09 cm-kg [ 1.17 ± .08 in-lbs. ] of torque during screw installation.
Use a minimum mount thickness of 3 mm.
Use safe ESD practices when handling and mounting the engine.
For a metallic mounting surface:
•
The die-cast engine chassis is at +Vcc. Use an insulator between the engine chassis and the host
(.005" thick PR4, or equivalent).
•
•
•
•
Use non-metallic nylon or equivalent M1.6 x .35 screws.
Do not exceeding 1.35 ± .09 cm-kg [ 1.17 ± .08 in-lbs. ] of torque.
Use a minimum mount thickness of 3 mm.
Use safe ESD practices when handling and mounting the engine.
Figure 6. IS4813 and IS4815 Engine Dimensions
Specifications are for reference only and are subject to change without notice.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IS4823 and IS4825 Bracketed (-1) Dimensions
The engine bracket has three M2 x 0.4 threaded inserts on the bottom for mounting the assembly with screws.
Two through holes are also provided as an alternative mounting method.
Warning: The limited warranty (on page 38) is void if the following recommendations are not adhered to when
mounting the IS4800 series laser scan engine.
When securing the engine by utilizing the three M2 threaded inserts:
•
•
•
•
Use M2 x 0.4 Phillips Pan Head, Type AB, Steel, Zinc Clear or equivalent screws.
Do not exceed 2.88 cm-kg [ 2.5 in-lb ] of torque when securing the engine assembly to the host.
Use a minimum mount thickness of 3 mm.
Use safe ESD practices when handling and mounting the engine assembly.
Figure 7. IS4823/IS4825 Bracketed (-1) Dimensions
Specifications are for reference only and are subject to change without notice.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IS4823 and IS4825 (-0) Decode Printed Circuit Board Dimensions
Warning: The limited warranty (on page 38) is void if the following recommendations are not adhered to when
mounting the IS4800 series laser scan engine.
When securing the decode board:
•
•
Use 3M™ 4032 1/32" double-coated urethane foam tape (or equivalent).
Use safe ESD practices when handling and mounting the decode board.
Figure 8. IS4823/IS4825 Decode PCB Dimensions
Specifications are for reference only and are subject to change without notice.
3M is a trademark of 3M and/or its subsidiaries worldwide.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Enclosure Specifications
The IS4800 laser scan engine series was specifically designed for integration into custom housings for OEM
applications. The scan engine’s performance will be adversely affected or permanently damaged when
mounted in an unsuitable enclosure.
Note:
THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040. USE ONLY AS COMPONENT.
integrating an IS4800 series scan engine into a system.
Electrostatic Discharge (ESD) Cautions
ESD has the ability to modify the electrical characteristics of a semiconductor device, possibly
degrading or even destroying the device. ESD also has the potential to upset the normal
operation of an electronic system, causing equipment malfunction or failure.
The scan engine has exposed electrical components.
•
•
•
DO NOT touch the leads of the visible laser diode (VLD) or other components.
ALWAYS use grounding wrist straps and a grounded work area when handling the engine.
Mount the engine in a housing that is designed for ESD protection and stray electric fields.
Grounding
If the scan engine is to be installed in a grounded host:
•
•
The die-cast engine chassis is at +Vcc. Use an insulator between the engine chassis and host.
Use non-metallic nylon or equivalent screws.
Power Supply
The IS4813/IS4815 non-decode engines are powered from the host device through the 3.3V or 5V and GND
pins of the engine’s 10-Pin ZIF connector. IS4823/IS4825 decode engine assemblies are powered from the
host device through the 3.3V or 5V and GND pins of the 12-Pin ZIF connector on the decode board.
This voltage must be maintained within the specified voltage range (see electrical specifications on page 25)
at the engine’s PCB. Voltage drops in the host flex cable must be taken into account (see Flex Cables
Power Sequencing
The IS4813/IS4815 non-decode engines are powered from the 3.3V or 5V power signal on the 10-Pin ZIF
connector and the IS4823/IS4825 decode engine assemblies are powered from the 3.3V or 5V power signal on
the decode board. Most of the host signals (signals present on the ZIF connector) are relative to this voltage.
Not all of these signals are overvoltage tolerant. Care must be taken to ensure that the relationship between
3.3V or 5V and the host signals are always met (see electrical specifications on page 25).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Flex Cables
Note:
To ensure optimum engine stability, use the flex cables shipped with the scan engine.
The host flex cable is used to carry power and data signals between the engine and the host system. The flex
cable should allow for a minimal voltage drop and maintain a good ground connection between the host and
the engine. In terms of grounding and voltage drop, a shorter cable is better. The 10-POS flex cable used to
connect the engine to the host or the engine to the decode PCB must be equal to or less than 67.5 mm in
length. The 12-POS flex cable used to connect the decode PCB to the host must be equal to or less than 80
mm in length.
In addition to power, the flex cable also carries the digital signals required for communication. The cable
design is especially important in USB interface applications due to the relative high speed of the USB signals.
The impedance of the cable should match, or be as close as possible to the impedance of the USB driver
(approximately 45 ohms per trace).
The routing of the flex cables plays a critical role in the system design. The host flex cable should be routed
away from high frequency devices with frequencies that can couple onto the flex cable and cause potential
data corruption or unwanted electromagnetic inference (EMI).
Thermal Considerations
The IS4800 laser scan engine series is qualified over the specified operational temperatures (0°C to 40°C) for
all operating modes. Ambient temperatures must not exceed this range in order to obtain optimal operation.
Operating the IS4800 in continuous mode for an extended period may produce considerable heating. This
mode should be limited and sufficient airflow should be provided whenever possible to minimize internal
heating. Excessive heating may potentially damage the IS4800 engine.
Printed Circuit Board (PCB) Component Clearance
Warning: When designing the IS4800 into the final product, eliminate all possible dangers of shorting
sensitive electronic components in the IS4800 engine. A short could enable the scan engine to
emit Class 3R radiation. Any CDRH filing will require a disclosure of the design ensuring a method
to mitigate a potential short.
Magnetic Sensitivity
The scan engine can be negatively affected by magnetic fields:
•
•
Use only non-magnetic screws and locating pins.
Do not mount the engine within 1.00" (25.4 mm) of any magnetic materials.
Airborne Contaminants and Foreign Materials
The scan engine has very sensitive miniature electrical and optical components that must be protected from
airborne contaminants and foreign materials. In order to prevent permanently damaging the scan engine and
•
Sealed to prevent infiltration by airborne contaminants and foreign materials such as dust, dirt, smoke,
and smog.
•
Sealed to protect against water, humidity and be non-condensing.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Exit Laser Beam Clearance
•
Keep the scan engine’s beam sweep free from obstructions. For detailed information on the exit beam
angle and location, please refer to Exit Beam Specifications on page 9.
•
A dark matte-finish on the internal walls of the housing can be utilized to avoid internal beam
reflections.
Return Aperture Clearance
•
ensure no obstructions in the paths of exit laser beam and return signal.
Output Window Properties
Note:
Contact a customer service representative to coordinate the best window material required to
maintain laser safety requirements for your application.
An improperly placed window has the serious potential to reduce the scan engine’s performance.
Careful consideration must be made when designing the output window’s distance and angle
placement relative to the scan engine’s exit beam and chassis.
Follow these guidelines when designing the output window.
•
Acceptable window materials include; Acrylic (cast or molded), float glass, CR-39, and Polycarbonate.
Note:
Molded polycarbonate is high in strength; however, it might exhibit a phenomenon called
birefringence. Birefringence refers to multiple indices of refraction within one material. This
condition will induce polarization effects that can be detrimental to scan performance of the
engine. Check with a representative before utilizing a transparent polycarbonate material
for the output window.
•
The exit window material must have a spectral transmission of at least 85% from 640 nm to 690 nm
and should block shorter wavelengths.
•
•
Red cell-cast acrylic is recommended.
The exit window must exhibit a wavefront distortion (transmission) of no more than 0.2 wavelengths
peak-to-valley maximum over any 0.08" diameter within the clear aperture.
•
•
The clear aperture of the output window must extend beyond the 54° beam sweep (see Exit Beam
Specifications on page 9).
It must have a 60-40 surface quality and be optically flat, clear, and free of scratches, pits, or seeds.
If possible, recess the window into the housing for protection or apply a scratch resistance coating (see
Output Window Coatings on page 14).
•
Apply an anti-reflective coating to the window surfaces to reduce the possibility of reflective light
interfering with the engine’s performance due to the window angle (see Output Window Coatings
on page 14).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Output Window Coatings
•
Anti-Reflection
An anti-reflective coating can be applied to the inside and/or outside of the window to reduce the
possibility of internal beam reflections interfering with the scan performance of the engine. If an anti-
reflective coating is applied, it is recommended that it be on both sides of the window providing a 0.5%
maximum reflectivity on each side from 640 to 690 nanometers at the nominal window tilt angle. The
coating must also meet the hardness adherence requirements of MIL-M-13508.
•
Polysiloxane Coating
Apply a polysiloxane coating to the window surface to help protect the window from surface scratches
and abrasions that may interfere with the scan performance of the engine. Recessing the window into
the housing can also provided added protection against surface damage such as scratches and chips.
If an anti-reflective coating is used, there is no need to apply a polysiloxane coating.
Output Window Angle
Note:
An improperly placed window has the serious potential to reduce the scan engine’s performance.
Careful consideration must be made when designing the output window’s distance and angle
placement relative to the scan engine’s exit beam and chassis.
It is important that angle of the window not be perpendicular to the exit beam of the scan engine. The angle of
the window can cause the beam’s laser light to reflect off the inside of the window back into the scan engine’s
optics ultimately degrading the engine’s performance.
Refer to the Figure 11 on page 15 and Figure 12 on page 16 for specifications on the minimum allowable
window angle required to avoid reflective beam interference.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum Allowable Window Angle Required
To Avoid Detrimental Internal Reflective Beam Interference
(at Positive Exit Beam Angle Tolerance)
Minimum Projected Distance (mm) from the
Minimum
Engine’s Base
to the Window’s Internal Surface (L)
Window Angle θ
5.0
28.0°
14.5°
10.5°
8.0°
7.0°
6.5°
6.0°
5.5°
5.0°
5.0°
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
Figure 11.
Specifications are subject to change without notice.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum Allowable Window Angle Required
To Avoid Detrimental Internal Reflective Beam Interference
(at Negative Exit Beam Angle Tolerance)
Minimum Projected Distance (mm)
Minimum
from the Engine’s Base to
Window Angle θ
the Window’s Internal Surface (M)
5.0
23.5°
16.5°
12.5°
10.5°
9.0°
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
8.0°
7.5°
7.0°
6.5°
6.0°
Figure 12.
Specifications are subject to change without notice.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Engine Field of View and Depth of Field
Field of View
Distance from Engine Face
Width of Field of View
57 mm (2.2")
50 mm (2")
254 mm (10")
264 mm (10.4")
Based on a .33 mm (13.0 mil) bar code and a horizontal exit laser beam.
Figure 13. Typical Field of View
Depth of Field vs. Minimum Bar Code Element
Depth of Field*
(In the Field of View)
Bar Code
Element Width
Start
End
Total
(From Engine Face)
(From Engine Face)
.13 mm
.19 mm
.26 mm
.33 mm
.49 mm
5.2 mil
70 mm (2.75")
57 mm (2.25")
50 mm (2.00")
50 mm (2.00")
75 mm (2.95")
95 mm (3.75")
171 mm (6.75")
210 mm (8.25")
254 mm (10.00")
300 mm (11.81")
25 mm (1.00")
114 mm (4.50")
160 mm (6.25")
204 mm (8.00")
225 mm (8.86")
7.5 mil
10.4 mil
13.0 mil
19.5 mil
1D
* For non-decode IS4813 and IS4815 engines, depth of field data is for reference only. Actual values may vary
depending on environmental conditions, host hardware, and decoding software.
Depth of field data was measured at 25°C under typical indoor lighting. Performance may vary depending on
testing conditions.
Specifications are subject to change without notice.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing Diagrams
Startup Condition Timing Diagram
The timing diagram below illustrates the correct power up procedure for the IS4813 and IS4815 engines.
Scan Enable and Laser Enable are host driven signals. The Scan Enable and Laser Enable signals should be
kept LOW (ON) at power up. Scan Control and Laser Control are engine driven signals.
The engine's onboard microcontroller drives the Scan Control and Laser Control signals so the engine's laser
will not turn ON before the scan mirror starts moving. This allows the onboard microcontroller to sense
immediately any malfunction with the engine's scan mirror, turning OFF the laser automatically regardless of
the state of Laser Enable signal being received from the Host.
To ensure scan data integrity the Scan Sense pulses are delayed for approximately 51 ms after the Laser
Enable signal goes LOW (ON). To save power, turn OFF power to the engine after the scan is complete or
when the engine is not scanning. To turn the engine's power OFF, the Laser Enable signal from the host
should be held HIGH (OFF) before turning OFF power to the engine.
Figure 14. IS4813/IS4815 Timing Diagram, Startup Condition*
* Typical timing for reference only, not to scale. Actual timing may vary.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Sense Timing Diagram
The Scan Sense signal is a 50% duty cycle square wave with the transitions from HIGH to LOW indicating a
change in the scan direction of the scanning beam (see Figure 14). Valid scan data occurs between the HIGH
to LOW transitions. Figure 15 illustrates the condition in which power to the engine stays ON. Scan Enable
and Laser Enable signals are controlled separately by the host.
The onboard microcontroller is programmed to ensure the engine's scan mirror is moving before the laser is
turned ON. This allows the host to turn ON Scan Enable and Laser Enable signals simultaneously without
worrying about laser safety. The Laser Enable signal can even be set LOW (ON) before the Scan Enable
signal goes LOW (ON). If the scan mirror is moving and Laser Enable signal goes LOW (ON), the onboard
microcontroller immediately turns ON the laser. If Laser Enable signal is LOW (ON) and Scan Enable signal is
HIGH (OFF) then the onboard microcontroller waits for the Scan Enable signal to go LOW (ON) and ensures
the scan mirror has started moving before turning the laser ON.
The Scan Sense line remains HIGH until the Scan Enable signal goes LOW (ON). After approximately
100 ms, it toggles with a 50% duty cycle representing the scan sweep direction. Valid scan data appears
within these pulses.
Figure 15. Timing Diagram Scan Enable and Laser Enable Controlled Separately*
* Typical timing for reference only, not to scale. Actual timing may vary.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Descriptions of IS4823 and IS4825 Operating Modes
Activation Modes
The following activation modes initiate the engine’s laser and motor drive circuitry for bar code scanning.
Activate Scanning with the External Trigger (Default).
An external I/O pin is used to enable the scanning cycle. A High-to-Low transition on the I/O signal is used to
activate scanning. The signal must be deactivated (HIGH) and re-activated for subsequent scanning cycles.
The scanning cycle is terminated based on the default period of time (2 seconds), a variable period of time,
when the I/O signal is deactivated (Low-to-High), or when a bar code is scanned and transmitted.
Activate Scanning on Receipt of the <DC2> Character
A received <DC2> character initiates the scanning cycle. The scanning cycle is terminated based on the
default period of time (2 seconds), variable laser timeout selected, receipt of <D4> character, or when a bar
code is scanned and transmitted.
Activate/Deactivate Scanning Using D/E
A received ‘E’ character initiates the scanning cycle. The scanning cycle is terminated based on the default
period of time (2 seconds), variable laser timeout selected, or receipt of a ‘D’ or when a bar code is scanned
and transmitted.
Activate Scanning with Address
A configurable address character is used to initiate scanning. The scanning cycle is terminated based on the
default period of time (2 seconds), variable laser timeout selected, or when a bar code is scanned and
transmitted.
Common Activation Mode Features
The following configurable activation mode features are available for the IS4823 and IS4825.
Variable Laser-On Timeout (1-second Increments)
A configurable time increment selected as the scanning laser–on time.
Allow Full Laser-On Cycle
The laser stays on for a full cycle even when a bar code is scanned and transmitted.
Blinky Mode
The scanner will blink for 60 cycles (approximately 30 seconds) once the scanning cycle is activated.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmit “NO READ” Message on Laser Timeout
If the scanning cycle terminates without scanning a bar code during the cycle, a “NO READ” message is
transmitted with the termination of the scanning cycle.
Activate the LED Signal During the “NO READ” Transmission
The LED signal is activated with the “NO READ” message. The LED signal is also activated after a successful
scan.
Enable RTS “NO READ” Pulse
A configurable RTS pulse width transmitted after the “NO READ” message has been transmitted.
Detect and Notify Mode
The external I/O pin used in the default activation mode is monitored during the inactive laser cycles. An <SI>
is transmitted when the I/O is active and an <SO> when it is inactive. Once the scanning activation cycle is
started, the external I/O monitoring status is maintained until the scanning cycle is terminated regardless of the
actual I/O level.
Continuous Blinky Mode
The scanner will continuously blink on and off, turning the scanning cycle on and off for all normal scanner
operations. If a bar code is scanned and transmitted, the same symbol timeout is maintained throughout the
cycle preventing additional scans of the same bar code when the scanner is in default mode.
Sleep Mode
Sleep Mode is a power saving mode that can be configured to occur in 1-second increments.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Configuration Mode
The IS4823/IS4825 can be configured by scanning configuration bar codes† or by serial commands sent from
the host device. With serial configuration, each command sent to the engine is the ASCII representation of
each numeral in the configuration bar code (see Figure 16). The entire numeric string is framed with an ASCII
[stx] and an ASCII [etx].
Do Not Include
in the Command
³
1 0 0 1 0 4
Include in the
Command
Figure 16.
Example 1:
String Sent to the Engine -
Feature
Host Command
[stx]100104[etx]
ASCII Representation (Hexadecimal Values)
Disable Codabar
02h 31h 30h 30h 31h 30h 34h 03h
[ack]
If the command sent to the engine is valid, the engine will respond with an [ack].
[nak]
If the command sent to the engine is invalid, the engine will respond with a [nak] then automatically
exit serial configuration mode. All the settings chosen in the failed serial configuration session will be lost.
There is a 20-second window between commands. If a 60-second timeout occurs, the engine will
send a [nak].
Enter Serial Configuration Mode
To enter serial configuration mode, send the following command, [stx]999999[etx]. The engine will not scan
bar codes while in serial configuration mode.
Note: Serial configuration mode uses the current Baud Rate, Parity, Stop Bits and Data Bits settings that
are configured in the engine. The default settings of the engine are 9600 bits-per-second, space parity,
2 stop bits, 7 data bits, and no flow control. If a command is sent to the engine to change any of these
settings, the change will not take effect until after serial configuration mode is exited.
Exit Serial Configuration Mode
To exit serial configuration mode, send the following command, [stx]999999[etx]. The engine will respond
with an [ack].
† Configuration bar codes are located in the MetroSelect Single-Line Guide, PN 00-02544 and the
Supplemental MetroSelect Configuration Guide, PN 00-05268.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Example 2:
The following sample illustrates the serial command sequence for configuring the engine for the factory
default settings, disabling Code 128 scanning, and adding a “G” as a configurable prefix.
Commands for features that require sequences of multiple bar codes for activation (i.e. prefixes, suffixes,
and timeout features) should be sent in the same order that they are normally scanned.
Feature
Host Command
[stx]999999[etx]
[stx]999998[etx]
[stx]100103[etx]
[stx]903500[etx]
[stx]0[etx]
ASCII Representation
Engine Response
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
Enter Configuration Mode
Load Defaults
02h 39h 39h 39h 39h 39h 39h 03h
02h 39h 39h 39h 39h 39h 38h 03h
02h 31h 30h 30h 31h 30h 33h 03h
02h 39h 30h 33h 35h 30h 30h 03h
02h 30h 03h
Disable Code 128
Configure Prefix #1
Code Byte 0
Code Byte 7
[stx]7[etx]
02h 37h 03h
Code Byte 1
[stx]1[etx]
02h 31h 03h
Exit Configuration Mode
[stx]999999[etx]
02h 39h 39h 39h 39h 39h 39h 03h
Abbreviated ASCII Table
Character
Hex Value
Decimal Value
[STX]
02h
03h
06h
15h
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
2
[ETX]
3
[ACK]
6
[NAK]
21
48
49
50
51
52
53
54
55
56
57
0
1
2
3
4
5
6
7
8
9
23
Download from Www.Somanuals.com. All Manuals Search And Download.
General Design Specifications
Operational
Light Source: Visible Laser Diode (VLD) @ 650 nm
Laser Power: 1 mW
Depth of Scan Field: 50 mm – 254 mm (2" – 10") for 0.33 mm (13 mil) bar codes
57 mm (2.2") @ 50 mm (2") from engine face
Width of Scan Field:
264 mm (10.4") @ 254 mm (10") from engine face
Scan Speed: 100 Scan Lines per Second Typical
Scan Pattern: Single Scan Line
Minimum Bar Width: 0.10 mm (4.0 mil)
IS4813 and IS4815
IS4823 and IS4825
Decoder Dependent
Symbologies Supported:
Autodiscriminates All Standard 1D Symbologies,
including GS1 DataBar
System Interface: IS4823 and IS4825
USB, TTL RS232
Print Contrast: 35% Minimum Reflectance Difference
IS4813 and IS4815
IS4823 and IS4825
Decoder Dependent
Up to 80 data characters (Maximum)
Number of Characters
Read:
Roll, Pitch, Yaw 42°, 68°, 52°
Mechanical
IS4813 / IS4815 Non-Decode Engine
8 g (0.282 oz)
Weight (Maximum): IS4823 / IS4825 Bracketed (-1) Assembly
IS4823 / IS4825 Non-Bracketed (-1) Assembly
15 g (0.529 oz)
10 g (0.353 oz)
IS4813 / IS4815 Non-Decode Engine
Termination:
10-PIN ZIF Connector
12-PIN ZIF Connector
IS4823 / IS4825 Decode PCB
Mounting: mounting guidelines.
Specifications are subject to change without notice.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical
IS4813
Input Voltage: 3.3VDC ± 0.3VDC
IS4815
5.0VDC ± 5%
350 mW
Power Consumption: 400 mW
Typical Operating Current: < 120 mA @ 3.3VDC
Peak Operating Current*: < 300 mA @ 3.3VDC
Standby Current: < 30 mA @ 3.3VDC
< 70 mA @ 5.0VDC
< 200 mA @ 5.0VDC
< 15 mA @ 5.0VDC
IS4823
USB
IS4825
USB
TTL
220 mA
50 mA
5.5 mA
N/A
TTL, RS232
135 mA
45 mA
Peak Operating Current*:
Idle Current:
270 mA
75 mA
65 mA
5.5 mA
165 mA
72 mA
Sleep Current:
53 mA
15 mA
Suspend Current (USB):
0.30 mA
N/A
Power Down Current
(TTL):
5.5 mA
15 mA
*
Peak Operating Current is the highest current drawn seen during normal operation. It does not include in-rush current
which is an exceptional current spike seen only once during initial powering up of the engine.
Environmental
Operating Temperature: 0°C to 40°C (32°F to 104°F)
Storage Temperature: -40°C to 70°C (-40°F to 158°F)
Humidity: 5% to 95% relative humidity, non-condensing
Vibration Protection: 7G over 10 – 500 Hz
Drop Protection: 2000G at a duration of 0.85 msec
EMI: Designed to meet EN55022 Radiated Class B emission limits
Specifications are subject to change without notice.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Detailed Electrical Specifications
Absolute Maximum Ratings
Signal
Signal Description
Minimum
Maximum
Vinput †
Voutput
Voltage Applied to Any input pin (except D+ and D-) *
Voltage Applied to Any output pin **
-0.3V
-0.3V
Vin
Vin + 0.3V
*
For USB version, Voltages on D+ and D- signal must conform to USB Specification
** Voutput must be less than 5.5V for all pins
†
If the Vinput signal is greater than VIN, current will flow from the input to the VIN pin through the
pull up resistors on the engine. In Suspend Mode, this may cause current to flow into the USB power.
This is not recommended.
IS4823 DC Operating Voltages
Signal
Signal Description
Operating Voltage
Minimum Maximum
Condition
VIN
3.0V
2.5V
3.6V
0.8V
0.8V
0.8V
VIH(1)
VIL(1)
Input High (RX, CTS)
Input Low (RX, CTS)
VIH(2)
VIL(2)
Input High (TTL_INV, nWake)
Input Low (TTL_INV, nWake)
Input High (EXT. Trigger)
0.8 x Vin
0.8 x Vin
0.8 x Vin
***
VIH(3)
VIL(3)
Input Low (EXT. Trigger)
VOH(1)
VOL(1)
VOH(2)
VOL(2)
VOH(3)
VOL(3)
Output High Voltage (TX,RTS)
Output Low Voltage (TX,RTS)
Output High Voltage (nBeeper, nGoodRead)
Output Low Voltage (nBeeper, nGoodRead)
Output High Voltage (Power down)
Output Low Voltage (Power down)
Isource = 16 mA
Isink = 16 mA
0.14 x Vin
3.6V
1.6V
Isink = 25 mA
Isink = 8 mA
***
3.6V
0.2V
*** PWRDWN, nGoodRead, and nBeeper are open drain outputs w/ 100K pull-ups to VIN. Actual VOH will be determined
by the parallel resistance of the 100K pull up and any external impedance.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
IS4825 DC Operating Voltages
Signal
Signal Description
Operating Voltage
Minimum Maximum
Condition
VIN
4.75V
2.5V
5.25V
0.8V
0.8V
0.8V
VIH(1)
VIL(1)
Input High (RX, CTS)
Input Low (RX, CTS)
VIH(2)
VIL(2)
Input High (TTL_INV, nWake)
Input Low (TTL_INV, nWake)
Input High (EXT. Trigger)
0.8 x Vin
0.8 x Vin
0.8 x Vin
***
VIH(3)
VIL(3)
Input Low (EXT. Trigger)
VOH(1)
VOL(1)
VOH(2)
VOL(2)
VOH(3)
VOL(3)
Output High Voltage (TX,RTS)
Output Low Voltage (TX,RTS)
Output High Voltage (nBeeper, nGoodRead)
Output Low Voltage (nBeeper, nGoodRead)
Output High Voltage (Power down)
Output Low Voltage (Power down)
Isource = 16 mA
Isink = 16 mA
0.14 x Vin
3.6V or 5.5V
1.6V
Isink = 25 mA
Isink = 8 mA
***
3.6V or 5.5V
0.2V
*** PWRDWN, nGoodRead, and nBeeper are open drain outputs w/ 100K pull-ups to VIN. Actual VOH will be determined
by the parallel resistance of the 100K pull up and any external impedance.
Current Draw @ 25°C
USB
VIN = 3.3V
TTL
VIN = 3.3V
Signal
Signal Description
VIN = 5V
130 mA
VIN = 5V
130 mA
Continuous Average current draw during
Scan mode continuous scan mode*
150 mA
130 mA
Average current draw while in idle
mode**
Average current draw while in sleep
mode**
Stand By
60 mA
50 mA
72 mA
53 mA
50 mA
5.5 mA
45 mA
15 mA
Sleep
Suspend
Average current draw in USB
Mode
5.5 mA
0.3 mA
N/A
N/A
suspend (USB version only)
(USB)
* Continuous Scan Mode current will vary based on object size, distance, and type.
The numbers listed above are typical.
**To conserve power for battery operated devices, Honeywell recommends using a power switch to operate
the scan engine.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Engine Terminations
IS4813 Engine Connections
10-Pin ZIF Connector
Signal Name
Pin
1
Function
No Connect
Power, VCC
No Connect
No Connect
2
3.3V ± 0.3V
3
No Connect
High = Laser OFF
4
5
Laser Enable*
Scan Enable*
Low = Laser ON, only if pin 5 (scan enable) is also Low
High = Engine OFF
Low = Engine ON
High = Bar
Digitized Bar
Pattern, Data Out
Figure 17. IS4813
6
7
Low = Space
Start of Scan,
Scan Sense
Level changes from high to low, or low to high, when the
laser changes direction at the start of the scan line.
8 and 9
10
Ground
Power Ground
No Connect
No Connect
IS4815 Engine Connections
10-Pin ZIF Connector
Pin
1
Signal Name
No Connect
Power, VCC
No Connect
Function
No Connect
5.0V ± 5%
2
3
No Connect
High = Laser OFF
4
5
Laser Enable*
Scan Enable*
Low = Laser ON, only if pin 5 (scan enable) is also Low
High = Engine OFF
Low = Engine ON
High = Bar
Figure 18. IS4815
Digitized Bar
Pattern, Data Out
6
7
Low = Space
Start of Scan,
Scan Sense
Level changes from high to low, or low to high, when the
laser changes direction at the start of the scan line.
8 and 9
10
Ground
Power Ground
No Connect
No Connect
* See Timing Diagrams on page 33.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Decode Printed Circuit Board Terminations
USB Decode PCB, 3.3V
12-Pin ZIF Connector
Pin Signal Name
Function
1
2
3
4
5
6
7
8
No Connect No Connection
+3.3V
GND
D-
Power: Supply Voltage Input, +3.3V ± 0.3V
Ground: Power and Signal Ground
Input: USB D- Signal
<reserved> Pin Function Reserved
D+ Input: USB D+ Signal
<reserved> Pin Function Reserved
PWRDWN
Output: Active High = IS4823 is in Power Down Mode
Output: Active Low, Signal Capable of Sinking Current
9
nBEEPER
Output: Active Low, Signal for Sinking Current (Good Scan)
10
11
12
nGood Scan
nEXT Wake
nEXT Trig
Input: Active Low, Wakes Engine From Suspend or Sleep
Mode
Input: Active Low, Signal Used as Trigger Input to Activate
the Engine
10-Pin ZIF Connector
Function
Pin Signal Name
I2C Data (Bi-Directional) – Devices Function as Auxiliary
Devices
1
SDA
2
3
GND
GND
Ground: Power and Signal Ground
Ground: Power and Signal Ground
Figure 19.
Level changes from High to low or low to high when the
laser changes direction at the start of the scan line
4
5
6
7
Scan Sense
Data
High = Bar
Low = Space
High = Engine OFF
Low = Engine ON
High = Laser OFF
Low = Laser ON
Scan Enable
Laser Enable
8
9
NC
No Connection
+3.3V
Power: Supply Voltage Output, +3.3V ± 0.3V
I2C Data (Bi-Directional) – Devices Function as Auxiliary
Devices
10
SCL
29
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Decode PCB, 5V
12-Pin ZIF Connector
Function
Pin
1
Signal Name
No Connect No Connection
2
+5.0V
GND
D-
Power: Supply Voltage Input, +5.0V ± 5%
Ground: Power and Signal Ground
Input: USB D- Signal
3
4
5
<reserved> Pin Function Reserved
D+ Input: USB D+ Signal
<reserved> Pin Function Reserved
6
7
8
PWRDWN
Output: Active High = Engine is in Power Down Mode
Output: Active Low, Signal Capable of Sinking Current
9
nBEEPER
Output: Active Low, Signal for Sinking Current (Good Scan)
10
nGood Scan
Input: Active Low, Wakes Engine from Power Down or
Sleep Mode
11
12
nEXT Wake
EXT Trig
Input: Active Low, Signal Used as Trigger Input to Activate
the Engine
10-Pin ZIF Connector
Function
I2C Data (Bi-Directional) – Devices Function as Auxiliary
Devices
Pin
1
Signal Name
SDA
2
GND
GND
Ground: Power and Signal Ground
Ground: Power and Signal Ground
Figure 20.
3
Level changes from High to low or low to high when the
laser changes direction at the start of the scan line
4
Scan Sense
Data
High = Bar
5
6
7
Low = Space
High = Engine OFF
Low = Engine ON
High = Laser OFF
Low = Laser ON
Scan Enable
Laser Enable
8
9
NC
No Connection
+5.0V
Power: Supply Voltage Output, +5.0V ± 5%
I2C Data (Bi-Directional) – Devices Function as Auxiliary
Devices
10
SCL
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TTL, RS232, 3.3V / 5V
12-Pin ZIF Connector
Function
Input: TTL RS232 Polarity Control with 33.2k ohm Pull-Up
Pin
1
Signal Name
TTLINV
2
+3.3V or 5.0V Power: Supply Voltage Input, +3.3V ± 0.3V or +5.0V ± 5%
3
4
5
6
7
GND
RxD
TxD
CTS
RTS
Ground: Power and Signal Ground
Input: TTL Level RS232 Receive Data
Output: TTL Level RS232 Transmit Data
Input: TTL Level Clear to Send
Output: TTL Level RS232 Request to Send
8
9
PWRDWN
nBEEPER
Output: Active High = IS4823 is in Power Down Mode
Output: Active Low, Signal Capable of Sinking Current
Output: Active Low, Signal for Sinking Current (Good Scan)
10
11
12
nGood Scan
nEXT WAKE
nEXT Trig
Input: Active Low, Signal Used to Bring Engine Out of
Power Down
Input: Active Low, Signal Used as Trigger Input to Activate
the Engine
10-Pin ZIF Connector
Function
I2C Data (Bi-Directional) – Devices Function as Auxiliary
Devices
Pin
1
Signal Name
SDA
2
GND
GND
Ground: Power and Signal Ground
Ground: Power and Signal Ground
3
Figure 21.
Level changes from High to low or low to high when the
laser changes direction at the start of the scan line
4
Scan Sense
Data
High = Bar
5
6
7
Low = Space
High = Engine OFF
Low = Engine ON
High = Laser OFF
Low = Laser ON
No Connection
Scan Enable
Laser Enable
8
9
NC
Power: Supply Voltage Output, +3.3V ± 0.3V or +5.0V ±
5%
+3.3V or 5.0V
I2C Data (Bi-Directional) – Devices Function as Auxiliary
Devices
10
SCL
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar Code Element Time Calculation
Realization of the full depth of field for all bar codes given in the specification is based on the ability of the
decoding hardware to resolve a varying range of minimum element times. The minimum element time
calculation for a given bar code size at a given distance is shown in Equation 1 (below).
Minimum Element Time = (Element Size / Spot Speed)
Equation 1.
Example:
Bar code Size = 5.2 mil
Spot Speed @ 95 mm from face = 650 inches/second
Minimum Element Time = (0.0052 inches/ (650 inches/second)) = 8.0 µsec
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance
Note: THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040. USE ONLY AS A COMPONENT.
The IS4800 Series Laser Scan engines are designed to meet the requirements of IEC Class 2 in accordance
with IEC 60825-1:2007. IEC Class 2 is defined as follows:
Emission Duration: Greater than 0.25 seconds
Accessible Emission Limit: Less than 0.001 W (1.0 milliwatt) average radiant power
The IS4800 laser scan engine series is registered with the Center for Devices and Radiological Health as a
laser “component”. The addition of shutdown controls, labeling and informational requirements are necessary
to achieve compliance with the performance standard published in the Code of Federal Regulations (CFR),
Title 21 Parts 1040.10 and 1040.11. It is the responsibility of the manufacturer who incorporates the
scan engine into their product to provide the additional performance, labeling, and informational
requirements necessary to comply with all federal laser safety regulations.
The specifications required for agency approval are not obtainable until the IS4800 engine is used in its final
configuration. Honeywell is unable to fulfill these requirements because the scan engine will operate differently
depending upon where it is used as a component. The following information concerning the scan engine
appears on the shipping label:
THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040.
USE ONLY AS A COMPONENT.
This device has been tested in accordance with and complies with IEC60825-1 ed2.0.
LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PRODUCT, 1.0mW MAX OUTPUT: 650nM.
The scan engine contains an embedded laser diode rated 640-660nM, 10mW maximum and a minimum beam
divergence of 6 degrees.
Caution: Use of controls, adjustments, or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
A statement of the compatibility requirements for a laser energy source to ensure safety.
Manufacturers incorporating unmodified IS4800 engines into their product may reference the following
accession number on items in their Laser Product Report that request information concerning features inherent
in the IS4800 engine design.
Accession Number: 0620138-00
It is the responsibility of the manufacturer who incorporates the scan engine into their product to
obtain country specific regulatory compliance prior to the sale of the product. Refer to one of the
following sections for further explanation.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
United States
Laser Safety
To assist with the FDA filing requirements (refer to Regulatory Requirements), Honeywell has registered the
scan engine with the FDA as a component. Customers can contact CDRH at the following address:
U.S. Food and Drug Administration
Center for Devices and Radiological Health
Document Mail Center – WO66-G609
10903 New Hampshire Avenue
Silver Spring, MD 20993-0002
Tel: 800-638-2041
Requirements for laser products are described in CFR (Code of Federal Regulation) Title 21, part 1040.10 &
1040.11 from the Government Printing Office. Copies can be ordered by calling 202-512-1800, ordering on
Superintendent of Documents
PO Box 371954
Pittsburgh, PA 15250-7954
Note: State and local governments may regulate the use products containing lasers. The manufacturer
should consult the applicable government regulations for more information.
Copies of Product Reporting Guides, other guides, and related documents are available as PDF documents
Manufacturers, International and Consumer Assistance (DSMICA) in Rockville, Maryland at
1-800-638-2041.
EMC
Certain combinations of scan engines and associated electronics may require testing to insure compliance with
the following Federal Communications Commission regulation: 47 CFR Part 15
Note: When using the scan engine with RF equipment, modems, etc. may require examination(s) to the
standard(s) for the specific equipment combination. It is the manufacturers’ responsibility to comply
with the applicable federal regulation(s).
The IS4800 series laser scan engine is designed to meet EN55022 Radiated Class B emission limits.
The engine was installed in a representative system and tested for compliance.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Canada
Laser Safety
The Radiation Protection Bureau currently accepts products meeting the FDA standards in Canada. For more
information contact:
Radiation Protection Bureau
775 Brookfield Road
Ottawa, Ontario K1A 1C1
EMC
Products meeting FCC 47 CFR Part 15 will meet Industry Canada interference-causing equipment standard for
digital apparatus, ICES-003. Additional testing is not required.
A written notice indicating compliance must accompany the apparatus to the end user. The notice shall
be in the form of a label that is affixed to the apparatus. The notice may be in the form of a statement
included in the user’s manual if, because of insufficient space or other restrictions, it is not feasible to affix a
label to the apparatus.
Europe
The CE Mark is required on products, which incorporate the IS4813, and the IS4815 scan engines if the
products are to be imported into European Economic Area (EEA) countries. Use of the CE Mark requires
compliance with directives and standards dependent upon the type of product. Information may be found at
Laser Safety
IEC 60825-1:2007,
EN 60825-1:2007
“Safety of Laser products”
Compliance with either of the standards listed above is required for the product to bear the CE mark.
Note: Non EEA countries may impose additional testing/certification requirements.
EMC
Certain combinations of IS4800 scan engines and associated electronics may require certification of
compliance with the European EMC Directive. EMC compliance of finished products in Europe can be
accomplished by the following method:
•
The manufacturer may certify to the EC’s Electromagnetic Compatibility Directive 2004/108/EC.
Compliance is required for the product to bear the CE Mark.
Note: Non EEA countries may impose additional testing/certification requirements.
The IS4800 series laser scan engine is designed to meet EN55022 Radiated Class B emission limits. The
engine was installed in a representative system and tested for compliance.
Electrical Safety
The scan engines are built to conform to the European Low Voltage Directive 2006/95/EC.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous laser light exposure. Under no circumstances should the customer attempt to service the laser
scanner. Never attempt to look at the laser beam, even if the scanner appears to be nonfunctional. Never
open the scanner in an attempt to look into the device. Doing so could result in hazardous laser light
exposure. The use of optical instruments with the laser equipment will increase eye hazard.
Atención
La modificación de los procedimientos, o la utilización de controles o ajustes distintos de los especificados
aquí, pueden provocar una luz de láser peligrosa. Bajo ninguna circunstancia el usuario deberá realizar el
mantenimiento del láser del escáner. Ni intentar mirar al haz del láser incluso cuando este no esté operativo.
Tampoco deberá abrir el escáner para examinar el aparato. El hacerlo puede conllevar una exposición
peligrosa a la luz de láser. El uso de instrumentos ópticos con el equipo láser puede incrementar el riesgo
para la vista.
Attention
L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peut entraîner de graves
irradiations. Le client ne doit en aucun cas essayer d'entretenir lui-même le scanner ou le laser. Ne regardez
jamais directement le rayon laser, même si vous croyez que le scanner est inactif. N'ouvrez jamais le scanner
pour regarder dans l'appareil. Ce faisant, vous vous exposez à une rayonnement laser qú êst hazardous.
L'emploi d'appareils optiques avec cet équipement laser augmente le risque d'endommagement de la vision.
Achtung
Die Verwendung anderer als der hier beschriebenen Steuerungen, Einstellungen oder Verfahren kann eine
gefährliche Laserstrahlung hervorrufen. Der Kunde sollte unter keinen Umständen versuchen, den Laser-
Scanner selbst zu warten. Sehen Sie niemals in den Laserstrahl, selbst wenn Sie glauben, daß der Scanner
nicht aktiv ist. Öffnen Sie niemals den Scanner, um in das Gerät hineinzusehen. Wenn Sie dies tun, können
Sie sich einer gefährlichen Laserstrahlung aussetzen. Der Einsatz optischer Geräte mit dieser
Laserausrüstung erhöht das Risiko einer Sehschädigung.
Attenzione
L’utilizzo di sistemi di controllo, di regolazioni o di procedimenti diversi da quelli descritti nel presente Manuale
può provocare delle esposizioni a raggi laser rischiose. Il cliente non deve assolutamente tentare di riparare
egli stesso lo scanner laser. Non guardate mai il raggio laser, anche se credete che lo scanner non sia attivo.
Non aprite mai lo scanner per guardare dentro l’apparecchio. Facendolo potete esporVi ad una esposizione
laser rischiosa. L’uso di apparecchi ottici, equipaggiati con raggi laser, aumenta il rischio di danni alla vista.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
Honeywell International Inc. ("HII") warrants its products and optional accessories to be free from defects in
materials and workmanship and to conform to HII’s published specifications applicable to the products
purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly
installed or used; (ii) damaged by accident or negligence, including failure to follow the proper maintenance,
service, and cleaning schedule; or (iii) damaged as a result of (A) modification or alteration by the purchaser or
other party, (B) excessive voltage or current supplied to or drawn from the interface connections, (C) static
electricity or electro-static discharge, (D) operation under conditions beyond the specified operating
parameters, or (E) repair or service of the product by anyone other than HII or its authorized representatives.
This warranty shall extend from the time of shipment for the duration published by HII for the product at the
time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during
the Warranty Period to HII factory or authorized service center for inspection. No product will be accepted by
HII without a Return Materials Authorization, which may be obtained by contacting HII. In the event that the
product is returned to HII or its authorized service center within the Warranty Period and HII determines to its
satisfaction that the product is defective due to defects in materials or workmanship, HII, at its sole option, will
either repair or replace the product without charge, except for return shipping to HII.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE FOREGOING WARRANTY IS
IN LIEU OF ALL OTHER COVENANTS OR WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR
WRITTEN, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT.
HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED
TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED
PARTS. IN NO EVENT SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY OF HII ARISING IN CONNECTION WITH ANY
PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON
CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL AMOUNT PAID TO HII FOR
THE PRODUCT. THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT
EVEN WHEN HII MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR
DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO NOT ALLOW THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which means that if any provision is held
invalid and unenforceable, such determination shall not affect the validity of enforceability of the other
provisions hereof. Use of any peripherals not provided by the manufacturer may result in damage not covered
by this warranty. This includes but is not limited to: cables, power supplies, cradles, and docking stations. HII
extends these warranties only to the first end-users of the products. These warranties are non-transferable.
The duration of the limited warranty for the IS4800 series is two (2) year(s).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Flex Cable............................................... 3, 4–5, 12
A
G
Accessories...........................................................3
Activate .................................................See Modes
Aperture
clearance..........................................................13
ASCII.............................................................22, 23
Assignments
Ground.......................................................... 11, 28
I
I/O.......................................................................20
Interface
TTL, RS232.............................................. 3, 8, 24
USB.................................................... 3, 8, 12, 24
pin ....................................................................28
B
L
Beam
Labels ...................................................................3
Laser
aperture........................................................9, 10
clearance....................................................11, 13
exit angle................................................9, 10, 14
specifications................................................9, 10
Bracket..........................................................3, 5, 7
aperture..........................................................4–5
beam................................................................11
class.................................................................25
enable ..............................................................28
mode................................................................20
power ...............................................................24
safety ................................................. 4–5, 34–37
VLD..................................................................11
LED.....................................................................20
Light Source........................................................24
C
CMOS .................................................................28
Compliance .........................................................38
Connector
10-Pin ZIF.........................................................28
pin assignments................................................28
Contaminants ......................................................12
Current ................................................................25
operating ..........................................................25
standby.............................................................25
Customer Service................................................38
M
Magnetic Sensitivity....................................... 11, 12
Mode
serial ................................................................22
Modes ........................................................... 20–21
D
N
D/E......................................................................20
DC2.....................................................................20
Decode............................................ 2, 3, 4–5, 8, 17
Depth of Field......................................................17
Design
Non-Decode........................................ 2, 3, 4, 6, 17
P
PCB ......................................................................8
Pin................................................................... 4, 28
Power............................................................ 11, 28
specifications..............................................24, 25
Dimensions..........................................................24
R
E
Regulatory Compliance................................. 34–37
Repair .................................................................38
RMA....................................................................38
RTS.....................................................................20
Electrical
Current Draw....................................................26
DC voltages......................................................26
Max Ratings......................................................26
safety................................................................25
Electrostatic Discharge........................................11
EMC ..............................................................34–37
EMI......................................................................12
Enclosure ............................................................11
S
Safety............................................................ 34–37
Scan
enable ..............................................................28
Scan Field
depth................................................................24
width.................................................................24
F
Field of View........................................................17
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Sense...................................................19, 28
Scan Speed.........................................................24
Screws ..............................................................6–8
Serial Configuration.............................................22
Service ................................................................38
Signals ................................................................26
V
Voltage.................................................... 11, 12, 25
W
Warranty .............................................................38
Weight.................................................................24
Window
T
angle .......................................................... 14–16
coatings...................................................... 13, 14
materials ..........................................................13
specifications.............................................. 13–16
transmission.....................................................13
Tape......................................................................8
Temperature..................................................12, 25
Thermal Temperature......................................1, 12
Timeout ...............................................................20
Timing .................................................................19
Torque...............................................................6–8
Trigger.................................................................20
Z
ZIF ........................................................ 4–5, 24, 28
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support
Technical Assistance
If you need assistance installing or troubleshooting your device, please contact us by using one of the methods
below:
Knowledge Base: www.hsmknowledgebase.com
Our Knowledge Base provides thousands of immediate solutions. If the Knowledge Base cannot help, our
Technical Support Portal (see below) provides an easy way to report your problem or ask your question.
Technical Support Portal: www.hsmsupportportal.com
The Technical Support Portal not only allows you to report your problem, but it also provides immediate
solutions to your technical issues by searching our Knowledge Base. With the Portal, you can submit and
track your questions online and send and receive attachments.
Web form: www.hsmcontactsupport.com
You can contact our technical support team directly by filling out our online support form. Enter your contact
details and the description of the question/problem.
Telephone: www.honeywellaidc.com/locations
For our latest contact information, please check our website at the link above.
Product Service and Repair
Honeywell International Inc. provides service for all of its products through service centers throughout the
world. To obtain warranty or non-warranty service, please visit www.honeywellaidc.com and select Support >
Contact Service and Repair to see your region’s instructions on how to obtain a Return Material Authorization
number (RMA #). You should do this prior to returning the product.”
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
00-02019 Rev M
4/12
Download from Www.Somanuals.com. All Manuals Search And Download.
|