Honeywell Home Security System K14114 3 06 RevB User Manual

ADEMCO LYNXR-I

Security Systems

Installation and Setup Guide

OFF

AWAY

STAY

AUX

K14114 3/06 Rev. B

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

SYSTEM FEATURES..................................................................................................................................4

MOUNTING THE CONTROL.....................................................................................................................5

WIRING CONNECTIONS...........................................................................................................................6

CONNECTING/CONFIGURINGCOMMUNICATIONS DEVICES.........................................................8

AC POWER AND BACKUP BATTERY....................................................................................................11

INSTALLING WIRELESS ZONES...........................................................................................................13

MECHANICS OF PROGRAMMING ........................................................................................................16

ZONE RESPONSE TYPE DEFINITIONS ...............................................................................................18

DATA FIELD DESCRIPTIONS................................................................................................................20

✻56 ENHANCED ZONE PROGRAMMING MODE................................................................................29

✻80 DEVICE PROGRAMMING MENU MODE ......................................................................................34

✻81 ZONE LIST MENU MODE................................................................................................................37

✻83 ENHANCED SEQUENTIAL MODE ................................................................................................38

✻84 ASSIGN ZONE VOICE DESCRIPTORS ..........................................................................................41

✻85 RECORD CUSTOM VOICE DESCRIPTORS...................................................................................43

VOICE PROMPT PROGRAMMING.........................................................................................................44

REMOTE PROGRAMMING/CONTROL (DOWNLOADING) ................................................................48

SYSTEM OPERATION..............................................................................................................................50

TESTING THE SYSTEM ..........................................................................................................................56

SYSTEM COMMUNICATION..................................................................................................................57

TROUBLESHOOTING GUIDE ................................................................................................................59

PROGRAMMING DEFAULT TABLES....................................................................................................62

INDEX.........................................................................................................................................................65

REGULATORY AGENCY STATEMENTS ..............................................................................................68

LIMITATIONS OF THIS SYSTEM STATEMENT..................................................................................69

SPECIFICATIONS.....................................................................................................................................70

CONTACTING TECHNICAL SUPPORT.................................................................................................70

SUMMARY OF CONNECTIONS DIAGRAM..........................................................................................71

WARRANTY ............................................................................................................................... Back Cover

- 3 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Features

LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N

LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.

Powerline Carrier Devices have not been evaluated by UL.

The LYNXR-I control is a self-contained, rechargeable wireless control/communicators that feature easy

installation and usage. A built-in speaker provides voice annunciation of system status along with voice

descriptors of each zone. An internal module (if provided) allows the LYNXR-I to communicate with the

Central Station via the Internet. The following illustration highlights the main features of this system.

FEATURES

•Real-time Clock display and Fixed-Word display

•Message Center (for user recorded messages)

•Voice announcement of system and zone status

•Voice chime

•Alarm Clock

•Reminder

ZONES and DEVICES

•Up to 24 wireless zones

SYSTEM POWER

•Primary Power: Ademco K10145X10

Plug-in Transformer, 110VAC to

9VAC, 25VA output (K10145CN in

Canada)

•Backup battery: Rechargeable

nickel-metal hydride battery pack

rated at 7.7Vdc.

(5800 Series Transmitters)

•Up to 16 wireless button zones

•Up to 8 Powerline Carrier Devices

•Supports wireless keypads

•X-10 Scheduling

•Latch Key Reports

•Automatic Stay Arming

8 USER CODES

• Installer code

• Master code

•Remote Phone Control

•“Follow Me” Reminder and System Announcements

• 5 Secondary codes

• Duress code

• 3 Panic functions

COMMUNICATION

• Ademco Low Speed

• Sescoa/Radionics

• Ademco Express

• Ademco Contact ID

• Paging feature

•Internet Central

OFF

AWAY

Station Communication

•GSM Cellular Central

Station Communication

STAY

ALARM OUTPUT

•Built-in sounder

•Piezo output

AUX

(30mA max.)

•Bell output

(120mA max.)

•Steady output for

burglary/panic

•Temporal pulse

output for fire alarms

•Long Range

Radio/Audio alarm

verification

PROGRAMMING

•Options stored in EEROM

•Can be uploaded, downloaded or

controlled via IBM-compatible

computer using Compass

downloader software and specified

HAYES modem

•Voice Prompt programming mode

OTHER FEATURES

•Exit error feature (detects difference between an

actual alarm and exit alarm caused by leaving a door

open after the exit delay expires)

SPECIAL FEATURES

•Two-way voice communication

•Speaker phone operation

•Event log stores up to 84 events

•Macro/ 1-button paging

•RF Jam Detection

•Remote Phone Control

•Compatible with Encrypted (High-Security) Devices

- 4 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Mounting the Control

Wall Mounting

The illustration below shows the front assembly separated from the back plate.

DO NOT disconnect the ribbon cable from the terminal strip board. Disconnect the cable only from the

front assembly board.

LOCKING TABS

1. Release the front assembly from the back

plate by depressing the two locking tabs

at the top of the unit with the blade of a

medium size screwdriver.

2. Once these tabs have been released,

insert the screwdriver in the side of the

case and release the side locking tabs by

gently twisting.

3. Carefully disconnect the ribbon cable from

the front assembly, leaving the ribbon

cable connected to the terminal block

PC board. The back plate contains the

terminal block for making wiring

connections.

LOCKING

TABS

RED WIRE

MARKING

LOCKING

TABS

4. Mount the back plate to a sturdy wall,

feeding the field wiring through the

appropriate openings in the back plate.

5. After wiring connections are made,

DISCONNECT

THIS END ONLY!

carefully reconnect the ribbon cable to

the front assembly PC board connector

(properly aligning the red wire).

6. Snap the front assembly to the back plate

so it is secured by the locking tabs.

07000-003-V1

Desktop Mounting

For desktop use the optional mounting base (model LYNX-DM, purchased separately) must be used.

1. Slide the control panel onto the mounting

base locking tabs.

2. Bring all wiring through the bottom of the

mounting base, using one of the three

wire entry locations, before making

OFF

ESCAPE

AWAY

ADD

STAY

connections to the control panel.

DELETE

AUX

SELECT

3. Use tie-wraps to secure the wiring to the

built-in wire loops as needed. Use the two

supplied screws to secure the control

panel to the mounting base.

WIRE ENTRY

KNOCKOUT

(1 of 3)

01009-004-V1

- 5 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Wiring Connections

Wiring Overview

The following summarizes the connections required. Refer to the Wiring Connections paragraph and the

Summary of Connections diagram on the inside back cover when making connections.

External sounders have not been evaluated by UL.

TELEPHONE

CONNECTIONS

LOCAL SOUNDER

DISABLE JUMPER

TERMINAL

STRIP

7845i-L COMMUNICATIONS PORT

(INTERNAL MODULE ONLY)

ALARMNET LRR/IP

COMMUNICATION PORT

SUPER HIGH CAPACITY

BATTERY CONNECTOR

STANDARD AND HIGH CAPACITY

BATTERY CONNECTOR

07000-005-V1

UL NOTE

THE MINIMUM WIRE SIZE USED FOR TELEPHONE

INSTALLATIONS MUST BE #26 GAUGE

HANDSET

PHONE

LINE

INCOMING

PHONE

LINE

ALL OUTPUT CIRCUITS ARE POWER LIMITED.

FUTURE

EARTH

USE

GROUND

GND

PHONE

SOUNDERS

PLCD

( )

(+)

POS

JACK

RJ11

( )

DATA

OUT

TIP RING TIP RING

SYNC

WARNING:

TO PREVENT

RISK OF SHOCK

DISCONNECT

TELEPHONE LINE

AT TELECOM

JACK BEFORE

SERVICING

THIS UNIT.

INTERNAL 7845i-L*

MODULE ONLY

STANDARD/HIGH

CAPACITY BATTERY

CONNECTOR

INCOMING

TELEPHONE

LINE

K10145X10

PLUG-IN

TRANSFORMER

9VAC, 25VA

SUPER HIGH CAPACITY

BATTERY CONNECTOR

PREMISES

PIEZO

TELEPHONE

BELL

ALARMNET LRR/IP

EARTH

GROUND

COMMUNICATIONS PORT

6-14VDC

30mA max.

FUTURE

USE

6-14VDC

LOCAL SOUNDER DISABLE

SHUNT REMOVE TO DISABLE

120mA max.

(e.g. WAVE2EX)

SYNC

COM

DATA

WEEKLY TESTING IS

REQUIRED TO ENSURE

PROPER OPERATION

OF THIS SYSTEM

THE LYNXR-I CONTROL IS COMPATIBLE WITH

THE FOLLOWING INTEGRAL RECHARGEABLE

BATTERY PACKS:

P/N LYNXRCHKIT-SC

P/N LYNXRCHKIT-HC

NOTE

P/N LYNXRCHKIT-SHA

USE ONLY THE K10145X10

OR K10145CN

TRANSFORMERS PROVIDED

X10

ONLY

REPLACE EVERY FOURYEARS

* WHEN AVAILBLE

CONNECTIONS

07000-009-V1

LYNXR-I Wiring Connections

- 6 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Wiring Connections

1. Make Earth Ground Connection - The designated earth ground terminal (1) must be terminated in a good earth ground

for the lightning transient protective devices in this product to be effective. The following are examples of good earth

grounds available at most installations:

Metal Cold Water Pipe - Secure a non-corrosive metal strap (copper is recommended) to the pipe that is electrically

connected and secured to which the ground lead is electrically connected and secured.

AC Power Outlet Ground - Available from 3-prong, 120VAC power outlets only. To test the integrity of the ground

terminal, use a three-wire circuit tester with neon lamp indicators, such as the UL Listed Ideal Model 61–035, or

equivalent, available at most electrical supply stores.

a. Connect terminal 1 to a good earth ground.

2. Make Phone Line Connections - For local or full line seizure proceed to the appropriate steps below.

Local Seizure

INCOMING

PHONE LINE

RING

TIP

a. Connect the incoming phone line to either the

8-position jack or terminals 2 (TIP) and 3

(RING) on the Lynx.

RED

GREEN

b. Connect the handset phone lines to either the

RJ11 jack or terminals 4 (TIP) and 5 (RING).

PREMISES PHONES

RJ31X

RING

Full Line Seizure: The control must be

placed in series with the incoming phone

line. Plugging the Direct Connect Cord

directly into the RJ31X jack, allows the control

to seize the phone line when an alarm occurs

and normal phone line usage by the premises

phones if the plug needs to be removed.

TIP

BROWN

GREY

DIRECT

CONNECT

CORD

c. Cut the incoming RING and TIP phone lines

(typically red and green, respectively) and

connect them to RJ31X terminals 4 (red) and

5 (green).

d. Connect the premises end of the cut RING

and TIP wires to RJ31X terminals 1 (grey) and

8 (brown) respectively.

8-POSITION

JACK

e. Wire the flying leads of a Direct Connect Cord

to the control’s phone terminals as shown in

the diagram or plug into the 8-position jack.

TIP

RING TIP RING

INCOMING

PHONE LINE PREMISES

PHONES

01000-008-V0

f. Plug the Direct Connect Cord into the RJ31X

jack.

Full Line Seizure Connections

Do not remove the local sounder shorting jumper (shunt).

External sounders and powerline carrier devices have not been evaluated by UL

LOCAL SOUNDER DISABLE: The Master Keypad’s built-in piezo sounder can be disabled by removing the

shorting jumper (shunt) on the terminal board. If disabled, however, no sounding will occur upon AC loss,

since the external sounder does not operate when AC power is lost.

3. Make External Sounder Connections - The control panel supports either a 6-14VDC piezo sounder (30mA max.) or

6-14VDC bell (120mA max.; e.g. ADEMCO WAVE2EX).

a. Connect a piezo sounder to terminals 10 (+) and 11 (–); OR a bell to terminals 11 (–) and 12 (+).

4. Disable Local Sounder Option - If required the Master Keypad’s built-in piezo sounder can be disabled.

a. Remove the shorting jumper (shunt) on the terminal board.

5. Make Powerline Carrier Device Connections - The control panel supports up to 8 Powerline Carrier Devices. If using

these devices, they must be connected to the K10145X10 transformer, as shown in the SUMMARY OF

CONNECTIONS diagram.

a. Connect the com/data/sync/ lines from the transformer to terminals 9, 13, and 14, respectively.

If not using the supplied connection cable, you may need to reverse the black and yellow wire connections.

Refer to the ✻80 Device Programming Menu Mode section for details on programming Powerline Carrier

Devices.

- 7 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Connecting/Configuring Communication Modules

General

This LYNXR-I supports central station reporting via long range radio and internet. It also supports

upload/download programming capability via the Internet or a Private local area network (Intranet). This

allows site maintenance independent of central station monitoring, and modification to sites globally via the

Internet or through a private LAN. Refer to the instructions provided with the LRR/IP Communications

Device being installed for additional information regarding its installation, programming, and registration.

Zone 103 is the supervisory zone for the Communications Device.

LYNXR-I does not support the 7845i-ENT remote access feature.

Connecting Long Range Radio and Internet Communication Devices

Connect and configure the communications device as follows (refer to the Installation Instructions for device

that you are installing for additional information):

The wire run between the LYNXR-I and the Communications Device must not exceed ten (10) feet.

The 7845ENT and 7845CV2 have been evaluated by UL for Household Burglary installations. The

communications modules have not been evaluated for Household Fire installations.

AlarmNet 7845i-L* Communications Device

1. Install the module into the LYNXR-I back plate and secure it with the two provided screws. Refer to the diagrams below.

2. Connect the provided ribbon cable between the module and the PC board. This cable provides DC power and ground for

the module and data in/data out connections.

3. Connect the device to the Internet via a cable/DSL modem and router or to an Intranet (LAN) via the appropriate Ethernet

connection.

* When available. The 7845i-L module has not been evaluated by UL.

CABLE

7720P PROGRAMMER

CONNECTION

RJ45 (FOR INTERNET

CONNECTION)

COMMUNICATIONS

PORT FOR

INTERNAL 7845i-L

MODULE ONLY

LRR / IP PORT

07000-004-V0

Installing the 7845i-L Communications Module

- 8 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

AlarmNet 7845GSM*, 7845i-GSM*, 7845i-ENT or 7845i, Communications Device

The 7845i-ENT/7845i and 7845CV2 can not be used for installations requiring 24-hour standby.

1. Connect the 4-wire communications cable to the LRR/IP Communications port on the LYNXR-I.

2. Connect the four wires to the specific Communications device as shown in the accompanying figures.

3. If you are installing a 7845GSM or 7845i-GSM you must also install a jumper between terminals 2 and 3 on the

communications device.

4. Connect the device to the Internet via a cable/DSL modem and router or to an Intranet (LAN) via the appropriate Ethernet

connection, if applicable.

TB1

RED

ECP (+) VOLTAGE INPUT

GND

4-WIRE CABLE (N4632-4)

BLK

YEL

Z1/Z2 OR DATA IN

Z3 OR DATA OUT

GRN

LRR/IP COMMUNICATIONS PORT

LYNXR-I CONTROL PANEL

7845GSM / 7845i-GSM

LYNX

STANDARD

CAPACITY

BATTERY

LYNX

(OPTIONAL)

REQUIRED FOR

24-HR BACKUP

SUPER HIGH

CAPACITY

BATTERY

7845i-GSM-010-V0

Connecting AlarmNet 7845GSM* / 7845i-GSM*

* When available. The AlarmNet 7845GSM and 7845i-GSM modules have not been evaluated by UL.

4-WIRE CABLE (N4632-4)

7845i-ENT / 7845i

TB 1

RED BLK GRN YEL

RED

BLK

GRN

YEL

LRR/IP COMMUNICATIONS PORT

LYNXR-I CONTROL PANEL

LYNX

STANDARD

CAPACITY

BATTERY

07000-013-V2

Connecting AlarmNet 7845i-ENT/7845i

- 9 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

LRR/IP Communications Device 24-Hour Standby Power

If you are installing the AlarmNet 7845GSM/7845i-GSM or 7845i-L you must install the Super High Capacity battery

P/N WALYNX-RCHB-SHA in the LYNXR-I.

The 7845i-ENT/7845i and 7845CV2 can not be used for installations requiring 24-hour standby.

AlarmNet 7845CV2

1. Connect the 4-wire communications cable to the LRR/IP communications port on the LYNXR-I.

2. Connect the four wires to the 7845CV2 as shown below:

4-WIRE CABLE (N4632-4)

BATTERY

ADEMCO

K4362

P1 BAT

LRR/IP COMMUNICATIONS PORT

RED

BLK

V+

GND

YEL

Z1/DATA IN

GRN

RAD FLT/ DATA OUT

LYNXR-I CONTROL PANEL

TB1

LYNX

STANDARD

CAPACITY

BATTERY

7845CV2

07000-011-V2

Connecting AlarmNet 7845CV2

Configuring Long Range Radio and Internet Communication Devices

1. Enable the communications device in programming field *55 and configure alarm reporting and module supervision in

programming field *77.

2. Program the device as required using the 7720P programmer (refer to the Installation Instruction for the device that you

are installing for additional information). Note that the device address must be set to 3.

1. When programming an AlarmNet 7845CV2 the radio’s “current limit” most option must be set

to [Y] (yes).

2. The device must be registered before downloading or alarm reporting can take place.

- 10 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

AC Power and Backup Battery

The system is powered by a 9VAC, 25VA Plug-in Transformer, ADEMCO K10145X10 (K10145CN in

Canada). Refer to the wiring table below for wire gauge and length.

Distance from Transformer

to Control

Wire Gauge

Use only the provided ADEMCO K10145X10

or K10145CN Transformer.

Up to 75 feet

#20

#18

#16

75 to 150 feet

150 to 300 feet

Wiring to the AC Transformer must not exceed 300 feet using 16-gauge wire. The voltage reading

between terminals 15 and 16 of the control must not fall below 9.00VAC.

Do not plug the transformer into the AC outlet until after all wiring connections have been made.

Backup battery

In the event of an AC power loss, the system is supported by a long life backup battery that is supervised for

connection and for low voltage conditions. If the battery is missing, or a low battery condition is detected, a

“low battery” message is displayed and a report is sent to the central station. In addition, the system will beep

once every 45 seconds to audibly indicate a low battery condition (press any key to stop the beeping).

AC Power and Rechargeable Backup Battery

Connecting AC Power and backup battery

RETAINER

1. Connect wires from the K10145X10 (K10145CN) in

NOTE

LYNXRCHKIT-HC

BATTERY PACK SHOWN

Canada) AC Transformer to terminals 15 and 16 as

shown in the wiring diagram.

2. Remove battery retainer.

3. Peel the backing from tape on the back plate.

BATTERY

PACK

4. Insert battery pack into back plate.

5. Install battery retainer.

TAPE

6. Connect battery connector to receptacle on terminal

block PC board.

7. After all wiring connections have been made, snap the

front assembly to the back plate and plug the

transformer into a 24-hour, 110VAC unswitched outlet.

Note: Rechargeable batteries may take up to 48-hours to

fully charge. The “LOW BAT” message should clear

within four hours or by entering Test Mode.

BATTERY

RECEPTACLE

WIRING

TERMINALS

07000-007-V0

Ensure the cover is snapped closed prior to applying AC power.

- 11 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

AC Power and Rechargeable Backup Battery

The LYNXR-I is equipped with an integral, replaceable, rechargeable battery pack rated at 7.7Vdc. Select

the appropriate battery pack, based on the installation’s requirement, and install the battery pack.

Model/Part Number

LYNXRCHKIT-SC

Battery StandbyTime

4-hours (minimum)

Low Battery Notification

Approximately 1-hour before battery depletion

LYNXRCHKIT-HC

LYNXRCHKIT-SHA

24-hours (minimum)

At least 1-hour before battery depletion

Replacing the Rechargeable Battery

LYNXRCHKIT-HC

LYNXRCHKIT-SC

1. When battery replacement is required,

unplug the transformer from the wall outlet,

and open the control panel cover.

RETAINER

BATTERY

PACK

2. Remove the battery retainer and disconnect

the battery pack connector from the

receptacle on the terminal block PC board.

3. Remove the battery pack from the back

plate.

TAPE

4. If required, replace the tape that secures the

battery pack.

BATTERY

CONNECTOR

5. Install a replacement battery pack (P/N

LYNXRCHKIT-SC, LYNXRCHKIT-HC or

LYNXRCHKIT-SHA) into the back plate.

6. Install the battery retainer.

7. Connect the battery connector to the

receptacle on the terminal block PC board.

BATTERY

RECEPTACLE

8. After the wiring connection has been made,

snap the front assembly to the back plate.

9. Plug the transformer into a 24-hour, 110VAC

unswitched outlet.

LYNXRCHKIT-SHA

RETAINER

10. Rechargeable batteries may take up to 48-

hours to fully charge. The “LOW BAT”

message should clear within four hours or

by entering Test Mode.

BATTERY

PACK

BATTERY

CONNECTOR

TAPE

BATTERY

RECEPTACLE

07000-006-V1

Ensure the control panel assembly is snapped closed prior to applying AC power.

- 12 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Installing Wireless Zones

General Information

Zones: The control supports up to 24 wireless zones using 5800 Series transmitters, and up to 16 wireless

buttons.

Range: The built-in RF receiver can detect signals from wireless transmitters within a nominal range of 200

feet.

Transmitters: 5800 Series transmitters have built-in serial numbers that must be entered into the system

using the ✻56 or ✻83 interactive mode, or input to the control via the downloader. 5800 Series transmitters

(except the 5800RL, which is described separately) do not have DIP switches. Each transmitter's zone

number is programmed into the system in ✻56 mode. Some transmitters, such as the 5816 and 5817, can

support more than one "zone" (referred to as loops or inputs). On the 5816, for example, the wire connection

terminal block is loop 1, the reed contact is loop 2. Each loop must be assigned a different zone number.

The 5816 and 5817 Transmitters do not have EOL supervision of their loop wiring and the loop wiring must

not exceed 3 feet.

The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5814, 5816TEMP, 5819, 5819S(WHS &

BRS), 5828/5828V and 5850(GBD) transmitters have not been evaluated by UL.

For button transmitters (RF "keys") such as the 5804 and 5801, you must assign a unique zone number to

each individual button used on the transmitter. Each button on the transmitter also has a pre-designated

loop or input number, which is automatically displayed.

House Identification

If you are using a 5804BD/5804BDV Wireless Keypad with the system, you must program a House ID Code

(01–31) in field ✻24 to establish proper communication, and the keypad must be set to the same ID. House

ID 00 disables all wireless keypads. An RF House ID is not necessary for other 5800 Series transmitters; the

entry should be left at “00” (default) in those cases.

Transmitter Supervision

Except for some transmitters/keypads that may be carried off-premises (5804, 5804BD, 5804BDV, and

5804E), each transmitter is supervised by a check-in signal that is sent to the receiver at 70–90 minute

intervals. If at least one check-in is not received from each supervised transmitter within a 12-hour period,

the "missing" transmitter number(s) and "FAULT" will be displayed. The supervision for a particular

transmitter in the system that may also be carried off the premises (5801, 5802MN) may be turned off by

entering it as a "UR" (unsupervised RF) type, as described in the ✻56 Enhanced Zone Programming Mode

section.

5800 Series transmitters have built-in tamper protection and will annunciate as a fault condition if covers

are removed.

Transmitter Input Types

Each of the following transmitters has one or more unique factory-assigned input (loop) ID codes. Each of the

inputs requires a programming zone (e.g., a 5804's four inputs require four button zones).

Transmitters can be entered as one of the following types (see transmitter’s instructions for appropriate input

type):

Type

"RF" (Supervised RF)

Description

Sends periodic check-in signals, as well as fault, restore, and low battery signals.

The transmitter must remain within the receiver's range.

"UR" (Unsupervised RF)

Sends all the signals that the "RF" type does, but the control does not supervise the

check-in signals. The transmitter may therefore be carried off-premises.

"BR" (Unsupervised Button RF)

These only send fault signals. They do not send low battery signals until they are

activated. The transmitter may be carried off-premises.

- 13 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Transmitter Battery Life

• Batteries in the wireless transmitters may last from 4–7 years, depending on the environment, usage, and

the specific wireless device being used. Factors such as humidity, high or low temperatures, as well as

large swings in temperature may all reduce the actual battery life in a given installation. The wireless

system can identify a true low battery situation, thus allowing the dealer or user of the system time to

arrange a change of battery and maintain protection for that point within the system.

• Button-type transmitters should be periodically tested for battery life. The 5801, 5802MN, 5802MN2,

5804, 5804BD, 5804BDV, and 5804E button transmitters have replaceable batteries.

Using the Transmitter Sniffer Mode

Use this mode after all transmitters have been entered to check that all transmitters have been properly

programmed.

1. Enter Installer code (4112) + [#] + 3.

Note: If the communicator is in the process of sending a report to the central station, the system will not go into the Sniffer

mode. If so, wait a few minutes and try again.

2. The keypad will display all zone numbers, which have a non-zero Zone Type (even if serial numbers were

not learned yet). Fault each transmitter in turn, causing each one to send a signal. As the system

receives a signal from each of the transmitters, the zone number of that transmitter will disappear

from the display. The transmitters may be checked upon installation, or in an installed system.

3. When all transmitters have been checked, exit Sniffer mode. Enter Installer Code (4112) + OFF.

Notes: (1) Sniffer mode does not automatically expire. You must manually exit (Installer Code + OFF) Sniffer

mode to return to normal operation.

(2) All BR-type units must physically be activated to clear the display, since they do not automatically send check-in

signals.

(3) When one button of a transmitter (RF, UR, or BR) is activated, all zones assigned to other buttons on that

transmitter are cleared. This also applies to 5816 and 5817 transmitters that have multiple loops (zones).

(4) Any transmitter that is not “entered” will not turn off its zone number.

Go/No Go Test Mode

5804E encrypted (High-Security) devices must be activated while the system is in Go/No Go Test Mode.

Refer to the transmitter’s installation instructions for complete details. The system will confirm

enrollment of the encrypted device by beeping two times.

The Go/No Go tests will verify adequate RF signal strength from the proposed transmitter location, and

allow you to reorient or relocate transmitters if necessary, before mounting the transmitters permanently.

This mode is similar to the transmitter Test mode, except that the wireless receiver gain is reduced. This

will enable you to make sure that the RF signal from each transmitter is received with sufficient signal

amplitude when the system is in the normal operating mode.

1. Enter Installer Code (4112) + [#] + 8.

2. Once you have placed transmitters in their desired locations and the approximate length of wire to be

run to sensors is connected to the transmitter's screw terminals (if used), fault each transmitter.

Conducting this test with your hand wrapped around the transmitter will cause inaccurate results.

On button type transmitters that have been programmed to set ARM AWAY, ARM STAY, or DISARM,

pressing a button will take the system out of the Go/No Go Test mode and cause the programmed action

to occur.

Note: On button type transmitters that have been programmed to set ARM AWAY, ARM STAY, or DISARM, pressing a button

will take the system out of the Go/No Go Test mode and cause the programmed action.

a. The keypad will beep three times indicating signal reception and will display the appropriate zone

number.

b. If the keypad does not beep, reorient or move the transmitter to another location. Usually a few

inches in either direction is all that is required.

If each transmitter produces the proper keypad response when it is faulted, you can then permanently

mount each of the transmitters according to the instructions provided with them.

Exit the Go/No Go Test mode by entering: Installer Code (4112) + OFF.

- 14 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

5800 Series Transmitter Loop Numbers (Refer to this information when programming transmitters)

The following illustration shows the compatible transmitters, their associated input types and loop

designations.

LOOP 3

LOOP 2

LOOP 4

YOU MUST

ENROLL

LOOP 4

YOU MUST

ENROLL

THIS

LOOP 4

YOU MUST

ENROLL

THIS

LOOP 2

LOOP 1

LOOP 2

LOOP 1

LOOP

THIS BUTTON

LOOP 3

BUTTON

•

LOOP 1

•

••

•

5800RL

SET

HOUSE ID

5800WAVE

PROGRAM

HOUSE ID

5801

ENROLL AS

"UR" OR "RF"

5802 MN2

ENROLL AS

"UR" OR "RF"

5804/5804E

ENROLL AS "BR"

5804BD/5804BDV

ENROLL AS "BR"

PROGRAM HOUSE ID

5802 MN

ENROLL AS

"UR" OR "RF"

LOOP 1

LOOP 2

(REED)

(PRIMARY)

LOOP 2

(REED)

LOOP 2

(AUX.

CENTER)

LOOP 1

(TERMINALS)

LOOP 1

(TERMINALS)

LOOP 1

(TEMP

ALTERNATE

POSITION

FOR LOOP 2

SENSOR)

LOOP 3

(AUX.

RIGHT)

5816

ENROLL AS "RF"

5816MN

ENROLL AS "RF"

5816TEMP

ENROLL AS "RF"

5817

ENROLL AS "RF"

5806/5807/5808/5808LST

ENROLL AS "RF"

5809

ENROLL AS "RF"

5814

ENROLL AS "RF"

LOOP 2

(REED)

ARMED

LOOP 2

(REED)

READY

LOOP 1

(SOUND)

LOOP 3

(TERMINALS)

LOOP 1

(MOTION)

LOOP 1

(INTERNAL

SHOCK

SENSOR

LOOP 1

(Green)

(Red)

LOOP 1

(TERMINALS)

(Yellow)

LOOP 3

(TERMINALS)

5818

ENROLL AS "RF"

5819

ENROLL AS "RF"

5819S (WHS & BRS)

ENROLL AS "RF"

5849

ENROLL AS "RF"

5850 (GBD)

ENROLL AS "RF"

5890/5890PI

ENROLL AS "RF"

5828/5828V

PROGRAM

HOUSE ID

01009-012-V4

Notes: (1) Loop 4 must be enrolled on the 5801, 5804, 5804BD, 5804BDV and 5804E transmitters, whether or not the loop

is used.

(2) 5804E encrypted (High-Security) devices must be activated while the system is in Go/No Go Test Mode. Refer

to the transmitter’s installation instructions for complete details. The system will confirm enrollment of the

encrypted device by beeping two times.

The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5814, 5816TEMP, 5819, 5819S(WHS & BRS),

5828/5828V and 5850(GBD) wireless transmitters have not been evaluated by UL.

Setting DIP Switches on the 5800RL Transmitter

Set the 5800RL Transmitters to the programmed House ID, by using the DIP switches.

(OFF position is indicated by ---)

Note: The 5800RL cannot be used in conjunction with the Auto Arm (scheduled arming) feature.

5800RL DIP SWITCH TABLE

SWITCH UP FOR "ON"

House

DIP SWITCH POSITIONS

House

DIP SWITCH POSITIONS

---

SW-1 ACTIVATES

MODE SETTING

SW-6 SETS

MODE

SWITCH DOWN

FOR "OFF"

---

2-6 SETS HOUSE ID

SHOWN SET FOR HOUSE ID# 12

01000-014-V1

Setting 5800RL DIP Switches

- 15 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Mechanics of Programming

General Programming Information

Programming options are stored in non-removable, electrically erasable, nonvolatile EEROM memory. The

system can be programmed at any time, even at the installer's premises prior to the actual installation.

Simply apply power temporarily to the Control and then program the unit as desired. There are four

programming modes:

•

Data field programming (used for setting various system options).

Interactive menu mode programming (used for programming zone information, programming

Powerline Carrier Devices, and for entering transmitter serial numbers).

•

Voice Prompt programming (used for setting various system options).

Pass-Thru programming (used for programming connected LRR/IP Communications Device).

The system can also be programmed remotely, using an IBM Personal Computer, a modem, and Compass

Downloader for Windows. See the Remote Programming/Control (Downloading) section.

Note: You may find it convenient to adjust the volume setting before entering the Program Mode. This will allow you to

clearly hear the feedback announcements or system beeps in the Programming Mode, of the system’s built-in

speaker. To adjust the volume, press FUNCTION + VOLUME+ [3] or [6]. Upon exiting the Program Mode, the

system will reset the volume to the default value (mid level).

Entering Program Mode

Use one of the following methods to enter Programming Mode:

1. Press both the [✻] and [#] keys at the same time, within 50 seconds after power is applied to the

Control or from exiting Programming mode, OR

2. After power-up, enter the Installer Code (4112) + 800 to enter Expert Programming mode (This

method disabled if Program mode is exited using ✻98). OR enter Installer Code (4112) + 888 to

enter Voice Prompt Programming mode.

If a different Installer Code has been programmed, use that code to enter the Programming mode.

3. Upon entering programming mode, the control will display “--” for up to two seconds indicating it is

communicating with the LRR/IP devices.

4. Once you have entered the Program mode, data field “20” (the first data field in the system) will be displayed and

both keypad LEDs will flash. If you have entered the Voice Prompt Programming mode. “Pro” will be displayed.

Programming a Data Field

1. Press [✻] + Field No. (for example, ✻21), followed by the required entry.

2. When you have completely programmed a data field, the keypad will “beep” three times and then

automatically display the next data field in sequence. To go to a different field, press [✻] plus the

desired field number.

3. If the number of digits that will be entered in a data field is less than the maximum number of digits

available (e.g. phone number field), enter the desired data, then press [✻] to advance to the next data

field.

4. If a nonexistent field has been entered, the keypad will display “EE”. Simply re-enter [✻] plus a valid

field number.

To view a data field without making changes: Enter [#] + Field No. Data will be displayed for that field.

To delete an entry in a field: Enter [✻] + Field No. + [✻]. (Applies only to fields ✻40–✻44, ✻88 and ✻94).

- 16 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Interactive Menu Mode Programming (✻56, ✻80, ✻81, ✻83, ✻84, ✻85)

Press [✻] + interactive mode No. (i.e., ✻56). The keypad will display the first of a series of prompts. A detailed

procedure (with displays of prompts) is provided in later sections of this manual.

Interactive Mode

Used to Program

Zone characteristics, report codes, and serial numbers

Powerline Carrier Devices

Zone Lists for powerline carrier activation

5800 Series transmitter serial numbers

Voice descriptors for each zone

56 Enhanced Zone Programming Mode

✻

✻80 Device Programming Menu Mode

✻81 Zone List Menu Mode

83 Enhanced Sequential Mode

✻84 Assign Zone Voice Descriptors

✻85 Record Custom Voice Descriptors

✻

Up to 5 custom voice descriptors for zones

Loading Factory Defaults

To load the factory defaults, enter the Programming mode, press ✻97, then press number 1, 2, 3, or 4 to

select from default tables 1-4 at the back of this manual, or press “0” if you are not selecting a default table.

If a default table is loaded, any data that has already been programmed into the system will be changed according to the

default table selected!

✻96 resets all subscriber account numbers and CSID in preparation for an initial download.

Exiting Program Mode

✻98 inhibits re-entry into the Expert or Voice Prompt Programming modes using the Installer Code.

✻99 allows re-entry into the Expert Program mode using Installer Code (4112) + 800 or into the Voice

Prompt Programming mode using Installer Code (4112) + 888.

Note: After exiting program mode (or upon power-up), the system takes up to a minute to reset. To bypass the reset

delay, press [#] + [0].

Pass-Thru Programming

This mode allows the Installer to use the LYNXR-I keypad and display to program the communications

device that is connected to the LYNXR-I. Refer to the communications device’s installation instruction to

determine whether this feature is supported.

Entering Pass-Thru Programming mode

1. After power-up, enter the Installer Code (4112) + 899.

2. Once you have entered Pass-Thru Programming mode “PtP” will be displayed on the keypad.

3. Refer to the Installation Instructions for the LRR/IP Communications Device being installed for

additional programming information.

LYNXR-I will abort this mode:

•

When it receives an abort command from the new communications device.

If it fails to communicate with an communications device after 20 attempts.

30 minutes after the last key has been pressed.

- 17 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Zone Response Type Definitions

General Information

During programming, you must assign a zone type to each zone, which defines the way in which the system

responds to faults in that zone. Zone types are defined below.

Zone type 00 is used to program a zone that is not used.

Type 00

Zone Not Used

Zone type 01 is usually assigned to sensors or contacts on primary entry and exit

doors.

Type 01

Entry/Exit

Burglary #1

Zone Characteristics:

•

Entry delay #1 is programmable from 0-99 seconds (field ✻35).

Exit delay is independently programmable from 0-99 seconds (field ✻34).

Exit and entry delays when armed in AWAY or STAY mode.

No entry delay when armed in STAY NO DELAY or AWAY NO DELAY mode.

Exit delay regardless of the arming mode selected.

01000-017-V0

Zone type 02 is usually assigned to sensors or contacts on which secondary entry and

exit doors that might be further from the keypad (typically used for a garage, loading

dock, or basement door).

Type 02

Entry/Exit

Burglary #2

Zone Characteristics:

•

Entry delay #2 is programmable from 0-99 seconds (field ✻36).

Exit delay is independently programmable from 0-99 seconds (field ✻34).

Secondary entry delay, if armed in the AWAY or STAY mode.

No entry delay when armed in the STAY NO DELAY or AWAY NO DELAY

mode.

01000-017-V0

•

Exit delay begins regardless of the arming mode selected.

Zone type 03 is usually assigned to all sensors or contacts on exterior doors and

windows.

Type 03

Perimeter

Burglary

Zone Characteristics:

•

Instant alarm, when armed in AWAY, STAY, STAY NO DELAY, or AWAY NO

DELAY mode.

01000-018-V0

Zone type 04 is usually assigned to a zone covering an entry area (i.e.: foyer, lobby,

or hallway) that one must pass upon entry (after faulting the entry/exit zone) to

reach the keypad. It provides an instant alarm if the entry/exit zone is not violated

first, and protects an area in the event an intruder has hidden on the premises

before the system is armed, or gains access to the premises through an unprotected

area.

Type 04

Interior,

Follower

Zone Characteristics:

•

Delayed alarm (using the programmed entry/exit time) if entry/exit (types 01 or

02) or interior-with-delay (type 10) zone is faulted first.

Instant alarm in all other situations.

Active when armed in AWAY or AWAY NO DELAY mode.

Bypassed automatically when armed in STAY or STAY NO DELAY mode.

5890 / 5890PI

01000-019-V1

•

Zone type 05 is usually assigned to a zone that contains foil-protected doors or

windows or covers a sensitive area (i.e.: stock room, drug supply room, etc.) It can

also be used on a sensor or contact in an area where immediate notification of an

entry is desired.

Type 05

Trouble by Day/

Alarm by Night

Zone Characteristics:

•

Instant alarm, when armed in AWAY, STAY, STAY NO DELAY, or AWAY NO

DELAY (night) mode.

•

Provides a latched trouble sounding from the keypad and, if desired, a central

station report during the disarmed state (day).

Zone type 06 is usually assigned to a zone containing an Emergency button (silent

emergency).

Zone Characteristics:

Type 06

24-hour

Silent Alarm

•

Sends a report to the central station but provides no keypad display or sounding.

- 18 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Zone Response Type Definitions

Zone type 07 is usually assigned to a zone containing an Emergency button

(audible emergency).

Type 07

24-hour

Audible

Alarm

Zone Characteristics:

• Sends a report to the central station, and provides alarm sounds

externally and at the keypad.

Zone type 08 is usually assigned to a zone containing a button for use in

personal emergencies or to a zone containing monitoring devices (i.e.: water

or temperature sensors, etc.).

Type 08

24-hour

Auxiliary Alarm

Zone Characteristics:

• Sends a report to the central station and provides an alarm sound at the

keypad. (No bell output is provided and there is no keypad timeout.)

Zone type 09 can be assigned to any wireless zone used as a fire

zone. This zone type is always active and cannot be bypassed.

Zone Characteristics:

Type 09

Supervised

Fire

5806/5807/5808

01000-020-V0

• Bell output will pulse when this zone type is alarmed.

Zone type 10 is bypassed when the panel is armed in the STAY or STAY NO

DELAY mode.

Zone Characteristics:

Type 10

Interior w/Delay

• Entry delay #1 (with programmed entry time) when armed in the AWAY

mode.

• Entry delay begins whenever sensors in this zone are violated, regardless

of whether an entry/exit delay zone was tripped first.

• No entry delay when armed in the AWAY NO DELAY mode.

• Exit delay regardless of the arming mode selected.

Zone type 20 is a special-purpose zone type used with 5800 Series wireless

pushbutton units.

Zone Characteristics:

Type 20

Arm–Stay

• Exit delay regardless of the arming mode selected.

• System is armed in the STAY mode when the zone is activated.

• Zone number is sent to the central station as a user number when arming

or disarming.

Zone type 21 is a special-purpose zone type used with 5800 Series wireless

pushbutton units.

Zone Characteristics:

Type 21

Arm–Away

• System is armed in the AWAY mode when the zone is activated.

• Zone number is sent to the central station as a user number when arming

or disarming.

Zone type 22 is a special-purpose zone type used with 5800 series wireless

pushbutton.

Zone Characteristics:

Type 22

Disarm

• Disarms the system when the zone is activated.

Zone type 23 can be used on a zone when a Powerline Carrier Device (e.g.,

X10) action is desired, but with no accompanying alarm (e.g., front door light).

Type 23

No Alarm Response

Zone type 24 is usually assigned sensors or contacts on exterior doors and

windows where bells and/or sirens are NOT desired.

Zone Characteristics:

Type 24

Silent Burglary

• Instant alarm, with NO audible indication when is armed in the AWAY,

STAY, STAY NO DELAY, or AWAY NO DELAY mode.

• Report sent to the central station.

Note: Keypad beeps if the zone is faulted when system is disarmed and Chime mode is

on.

- 19 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

Defaults (where applicable) are Indicated in bold text.

The following pages list all data fields in this Control (in numerical order). Use the blank programming form

to record the data for this installation. Note that both keypad LEDs flash while in Programming mode.

Note: Entering a number other than the one specified will give unpredictable results.

The Installer Code is used to enter the 4-digit Master Security

Code. See "Master Code" in the System Operation section for

procedure.

Installer Code

Enter 4 digits, 0-9

✻

If enabled, security code is not required to arm the system. The

user simply presses and holds down the AWAY or STAY key to

arm.

Quick Arm Enable

0 = do not allow quick arm

1 = allow quick arm

✻21

✻22

✻23

This option allows the choice of either always backlighting the

keypad or turning the backlighting off after 10 seconds of

keypad inactivity.

Keypad Backlight Timeout

0 = no timeout; always backlight keys

1 = turn backlighting off after inactivity

All zones bypassed by this function will be displayed after the

bypass is initiated.

Forced Bypass

0 = no forced bypass

1 = provide automatic bypass of all open (faulted) zones

UL installations: must be 0 (no forced bypass)

The House ID identifies receivers and wireless keypads.

If a 5804BD/5804BDV Transmitter is to be used, a House ID

Code MUST be entered, and the keypad should be set to the

same ID.

Powerline Carrier Devices require a House ID. This field

identifies this House ID to the Control. The Powerline Carrier

Devices are programmed in field ✻80.

RF House ID Code

✻24

✻25

00 = disable all wireless keypad usage

01-31 = House ID

Powerline Carrier Device (X10) House ID

0 = A

1 = B

2 = C

3 = D

4 = E

5 = F

6 = G

7 = H

8 = I

9 = J

# + 12 = M

# + 13 = N

# + 10 = K # + 14 = O

# + 11 = L # + 15 = P

This option allows the installer to define the specific zones

intended to chime when faulted while the system is in Chime

mode. If enabled, these zones are defined in zone list 3 (see ✻81

Zone List Menu Mode).

Chime by Zone

✻26

0 = no (chimes on fault of any entry/exit or perimeter

zone when Chime mode is activated

1 = yes (chimes on fault of those zones assigned to

Zone List 3 when Chime mode on)

Refer to the User’s Manual for setting the clock time and date.

Enter # + 10 for 10, # + 11 for 11, and # + 12 for 12.

Real Time Clock Display

0 = do not display the time

1 = display the time

✻27

✻29

Daylight Savings Time Start/End Month

0, 0 = no daylight saving time used

1-12 = start month and end month

Enter the appropriate start and end weekend of the month.

Daylight Savings Time Start/End Week

✻30

✻31

0 = disable

4 = fourth weekend

1 = first weekend of month 5 = last weekend

2 = second weekend

3 = third weekend

6 = next to last

7 = 3^rdfrom last

This field applies only to burglary zones (zone response types 1-

5, 10), and affects long range radio reporting but does not affect

central station reporting.

Single Alarm Sounding Per Zone

(per armed period)

0 = no limit on alarm sounding per zone

1 = limit alarm sounding to once per arming period for

a given zone

Note: This field applies only to the bell and does not affect

keypad sounds.

UL installations: must be 0 (no limit)

This Control complies with NFPA requirements for temporal

pulse sounding of fire notification appliances.

Temporal pulse sounding for a fire alarm consists of the

following: 3 pulses – pause – 3 pulses – pause – 3 pulses. . .

Fire Sounder Timeout

✻32

✻33

0 = yes, fire sounder timeout after time programmed in

field ✻33

1 = no fire sounder timeout; continue sounding until

manually turned off

This field determines whether the external sounder will shut

off after time allowed, or continue until manually turned off.

UL installations: must be set for a minimum of 4 min

(option 1)

Alarm Bell Timeout

0 = No timeout

1 = 4 min

2 = 8 min

3 = 12 min

4 = 16 min

- 20 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

The system will wait the time entered before sounding an

alarm if the exit door is left open after the system has been

armed.

Exit Delay

00-99 = exit delay time in seconds

✻34

UL installations: must be set for a maximum of 60 seconds

The system will wait the time entered before sounding alarm upon

entering if system is not disarmed. UL installations: must be set for a

maximum of 45 seconds

Entry Delay 01

✻35

✻36

✻37

00-99 = entry delay time in seconds.

The system will wait the time entered before sounding alarm

upon entering.

UL installations: must be set for a maximum of 45 seconds

Entry Delay 02

00-99 = entry delay time in seconds.

Exit Warning: Sound consists of slow continuous beeps until

last 5 seconds, when it changes to fast beeps. The warning

sound will end at the termination of exit delay.

Audible Exit Warning/Quick Exit

Exit Warning

0 = no exit warning

sound

1 = provide exit

warning sound

Quick Exit

0 = no quick

exit

1 = allow quick

exit

Quick Exit: If enabled, user can restart the exit delay time after

arming in STAY mode by entering the user code and pressing

the STAY key, or by pressing the STAY key if Quick Arm is

enabled. This avoids having the user disarm then re-arm the

system after allowing someone to enter or exit

when armed AWAY

Confirmation of arming is provided by a 1/2 second external sounder

“ding” that sounds when closing report is sent, or at the end of exit delay.

Confirmation of Arming Ding

0 = no ding

1 = confirmation ding after arming system

2 = confirmation ding after arming from RF button or RF

keypad only

✻38

✻39

If Option 2 is selected the external sounder “ding” occurs immediately

after the system receives the RF transmission.

When the system powers up armed, an alarm will occur 1

minute after arming if a zone is faulted, and any bypassed

zones will be unbypassed.

Power Up In Previous State

0 = always power up in a disarmed state

1 = assume the system status prior to power-down

Note: If the previous state was armed AWAY or STAY, the

system will not respond to sensor changes for 1 minute,

which allows time for sensors such as PIRs to stabilize.

UL installations: must be 1 (power up in previous state)

✻

DIALER PROGRAMMING ( 40– 50)

✻

* ;

Fields 40, 41, 42: Enter up to the number of digits shown. Enter 0–9, # + 11 for ‘ ’ # + 12 for ‘#’; # + 13 for a pause

(2 seconds)

NOTE: Whenever AAV is used, primary (field ✻41) and secondary (field ✻42) phone numbers should be preceded with the

call waiting disable command. Otherwise, there is the possibility of connection of the third party to LYNXR-I during

AAV mode.

✻

If fewer than 6 digits need to be entered, exit by pressing [ ].

To clear entries from field, press 40 .

PABX Access Code

✻40

✻41

✻

Enter up to 6 digits if PABX is needed to access an

outside line.

✻

If fewer than 20 digits entered, exit by pressing [ ]. To clear

Primary Phone No.

Enter up to 20 digits.

✻

entries from field, press 41 .

Note: Backup reporting (8 attempts are made to the secondary

phone number if no kissoff is received after 8 attempts to

the primary number) is automatic only if there is a

✻

secondary phone number (field 42).

✻

If fewer than 24 digits entered, exit by pressing [ ]. To clear

Secondary Phone No.

Enter up to 24 digits.

✻42

✻

entries from field, press 42 . See backup reporting note for

field 41. If using the paging feature, enter the pager phone

✻

number here.

- 21 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

✻

All four digits of the Subscriber Account number must be entered in Fields 43 and 44. If ten-digit format is selected

✻

in 48 (option 5), all ten digits of the Subscriber Account number must be entered.

✻

Fields 43 and 44:

✻

Enter [ ] as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first

✻

digit of a 4-digit account number for Nos. 0000–0999. Enter [ ] as the fifth digit if a 4-digit account number (for 3+1,

✻

✻ or ✻

✻

CID®) is used. Exit field by pressing [ ] if only 3 digits are used. To clear entries from field, press 43

44 . See

blank Programming Form for examples of account number entries. If using the paging feature, do not enter a leading 0

in the subscriber account number, and do not use digits A-F anywhere in the number. Some paging systems provide

voice mail capability, which is activated by a leading 0 in the message. Enter digits 0–9; # +11=B; # +12=C; # +13=D; #

+14=E; or # +15=F.

Enter the primary subscriber account number.

To clear entries from field, press 43 .

Primary Subs Account No.

✻43

✻44

✻

Enter a four or ten digit account number.

Enter the secondary subscriber account number.

Secondary Subs Account No.

Enter a four or ten digit account number.

✻

To clear entries from field, press 44 .

Field 46: Enter up to 24 digits. Do not fill unused spaces. Enter 0-9, #+11 for ‘*’; #+12 for’#’; #+13 for a pause (2 seconds).

This option allows the user to schedule a time driven message.

“Follow Me Reminder” Phone Number

Enter up to 24 digits.

✻46

When activated the system will dial the phone number

programmed and deliver a voice message (custom words 72, 73

and 74). This option is only supported when the pager or follow

✻

me feature is enabled in field 49 (option 6-9 or 10-13).

If using the Follow Me Reminder feature, enter the phone number

✻

here. If fewer than 24 digits are entered, exit by pressing [ ]. To

✻

clear entries from the field press 46 .

The telephone message can be terminated (acknowledged) by

pressing any key on the telephone keypad. Pressing any key on

the local LYNXR-I keypad will terminate (acknowledge) both the

follow me and the local reminder announcements.

Note: The follow me reminder announcement will be terminated if

any other event requires the system to dial out or if an

audible alarm has occurred.

This option is used to enter the correct type of phone dialing

(pulse or tone), and to select the correct WATS line option for the

Central Station. This option is used to activate the Speaker Phone

option.

Phone System Select

✻47

✻48

Central

Station

Dialing Mode

Pulse

Tone

Pulse

Tone

No WATS 0 = No

Speaker

1 = No

Speaker

Phone

4 = With

Speaker

Phone

5 = With

Speaker

Phone

Note: If using pulse dialing, you must enter the numbers slowly in

Phone

order to allow the pulse dialer time to operate.

WATS

2 = No

Speaker

Phone

3 = No

Speaker

Phone

6 = With

Speaker

Phone

7 = With

Speaker

Phone

✻

Enter as the 4th digit of 43 through 44, if 3+1 dialer

reporting is to be used. (For an explanation of these formats, see

the System Communication section of this manual.)

Report Format for Primary/Secondary

Primary

See choices below

Secondary

See choices below

Notes: (1) The maximum number of alarm and alarm restore

0 = 3+1; 4+1 ADEMCO Low Speed Standard

1 = 3+1; 4+1 Radionics Standard

2 = 4+2 ADEMCO Low Speed Standard

3 = 4+2 Radionics Standard

5 = ADEMCO Contact ID® Reporting with 10-digit

subscriber account number

reports during one armed period is determined by field

✻

92.

(2) If Option 5 is selected a 10-digit account number must

✻

be entered in Fields 43 or 44.

(3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must

be selected for AVM.

6 = 4+2 ADEMCO Express

7 = ADEMCO Contact ID® Reporting with 4-digit

subscriber account number

8 = 3+1; 4+1 ADEMCO Low Speed Expanded

9 = 3+1; 4+1 Radionics Expanded

- 22 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

This field is used to select a reporting option as follows:

Enter: 0 - 5 when reporting to telephone receivers.

6 - 9 when reporting to a pager is desired.

Split/Dual Reporting

✻49

To Primary

To Secondary

0 = All reports

None, unless primary

fails, then all

10 - 13 when reporting to an auxiliary telephone receiver.

1 = Alarms, Restore, Cancel

2 = All except Open/Close, Test

3 = Alarms, Restore, Cancel

4 = All except Open/Close, Test

Others

Open/Close, Test

All

Pager Report Format

Options 6-9 send reports to the primary phone number, in a

✻

format defined in Field 48, and send reports to a pager, which

has its phone number entered as the secondary phone number in

5 = All reports

✻

Field 42. The pager report is a 7-digit code, with optional 16-

digit prefix, in the following format:

To Primary

To Paging Number

AAAAAAAAAAAAAAAA-EEE–0NNN where:

AAA = Optional 16 digits for PIN number, etc. See Field 88 for

‡

6 = All reports except Open/Close

Alarms, Open/Close

Troubles

Alarms, Troubles

✻

full description of these characters.

EEE = 3-digit Event Code as follows:

911 = Alarm (NN = zone number)

101 = Open, system disarmed (NN = user no.)

102 = Close, system armed (NN = user no.)

811 = Trouble (NN = zone no.)

7 = All reports

8 = All reports

‡

Alarms, Open/Close

Troubles

‡

9 = All reports except Open/Close

Open/Close

To Primary

To Follow Me System

Phone Number

0 =

Always displayed before 3-digit user/zone no.

‡

NNN = 3-digit user number or zone number, depending on the

type of event (EEE) that occurred.

10=All reports except Open/Close

Alarms, Open/Close

Troubles

Alarms, Troubles

11 = All reports

12=All reports

Follow Me System Report Format

‡

Alarms, Open/Close

Troubles

Options 10-13 send reports to the primary phone number, in a

✻

format defined in Field 48, and sends voice message to the

‡

✻

13=All reports except Open/Close

‡

Open/Close

secondary phone number entered in Field 42.

The message is a repeatable system status announcement. If the

Will report Users 0, 5-8, and, if using wireless button-type

devices, will report the zone number of the arm or disarm

button 26-33. All other zones and users are not reported.

✻

manual paging option has been programmed in Field 87, the

message will repeat “system, system…..”.

The message can be terminated by pressing any key on the

telephone keypad.

If enabled, provides delay of burglary report to the central station,

and allows time for the subscriber to avoid a false alarm

transmission. The delay applies only to zone type 3 and 5 alarms

and not to zone type 24 alarms (silent burglary) or to 24-hour zone

types 6, 7, and 8 (silent panic, audible alarm, auxiliary alarm),

which are always sent as soon as they occur.

15-Second Dialer Delay (Burglary)

0 = no dialer delay

1 = provide 15-second delay of burglary alarm report

when armed away

✻50

UL installations: must be 0 (no delay)

✻

Test report code entered in field 64 is sent.

Periodic Test Report

✻51

✻52

0 = no test report

2 = weekly

1 = once every 24 hrs 3 = once every 30 days

Select the time for the first report following programming or

downloading.

First test Report Offset

0 = 24 hrs after exit program mode or download

1 = 6 hours after exit program mode or download

2 = 12 hrs after exit program mode or download

3 = 18 hrs after exit program mode or download

Sescoa/Radionics Select

0 = Radionics (0–9, B–F reporting)

1 = SESCOA (0–9 only reporting)

If disabled, selects Radionics, which uses hexadecimal 0-9, B-F

reporting.

If enabled, selects Sescoa, which uses only numeric reporting (0-9).

Select 0 for all other formats.

✻53

If enabled, notifies the central station if an end user is not

operating their security system by sending a System Inactivity

report 654. The report will be sent only to the Primary phone

number and only if Contact ID® format was selected.

Lack of Usage Notification

✻

0 = Disabled

1 = 1 day

4 = 90 days

5 = 180 days

6 = 365 days

2 = 7 days

3 = 27 days

✻

Note: The report will follow the 49 = 0 rules, no matter which

Note:There is no local annunciation indicating that this

✻

selection was made in 49.

report has been sent to the Central Station.

This option is used to enable/disable Central Station reporting via

the LRR/IP Communications Device (See Field *77). Upload/

download via the Internet IP module is not affected by this entry.

Zone 103 supports the LRR/IP Communications Device.

Enable/Disable LRR/IP Communications

✻

Device

0 = disable

1 = enable

Notes: (1) When LYNXR-I is in programming mode it will not

communicate with the LRR/IP device. As a result the

LRR/IP device will transmit 355 (event and restore)

reports to the Central Station.

(2) Zone 103 can not be bypassed.

- 23 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

For Event Logging, Option 2 must be selected.

RF Jam Detection

✻58

0 = no jam detection

1 = RF jam detection with event logging, but no

central station report

If the control detects an RF Jam condition, a “FAULT” message

appears for zone 90. The Contact ID® code for RF Jam is 344.

2 = RF jam detection with event logging and with

central station report (if trouble/restore report is

enabled in fields ✻60, ✻71)

✻

SYSTEM STATUS AND RESTORE REPORT CODES PROGRAMMING ( 59 – 76, & 89)

✻

Program Report Codes using the interactive 56 Enhanced Zone Programming Mode, or codes can be entered in data

✻

fields 59- 76, 89. The following is a set of guidelines when programming report codes. The actual report code digits

that you enter depend upon the particular installation, and should be in agreement with you and the central station

office receiving the signals.

With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, A, B, C, D, E, or F. Enter "#+10" for A

(reports a “0” on some receivers), "#+11" for B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F. Entering "0" in the

first box will disable a report. Entering "0" in the second box results in automatic advance to the next field.

With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, or A–F, as described above.

Entering "0" in the first box will disable a report. Entering "0" in the second box will eliminate the expanded message for

that report.

With ADEMCO Contact ID® Reporting: Enter a digit in the first box to enable the zone to report. Use a different

digit for each zone until you have used up available digits. If the number of zones exceeds the number of available

digits, begin with digit 1 again. This is an "enabling" code only and is not the actual code sent to the central station

office. Entries in the second boxes will be ignored. For system status (non-alarm) codes, enter a “1” in the first box for all

the system conditions you want to send to the central station. A "0" in the first box disables the report.

✻

SYSTEM STATUS REPORT CODES ( 59– 68)

If the system is armed and an entry/exit or interior zone is still

open after the exit delay time has expired, an alarm will sound

at the keypad and external sounder. If the system is disarmed

before the end of the entry delay that immediately follows, the

alarm sounding will stop and no message will be sent to the

central station. The keypad will display “CA (CANCELED

ALARM).”

Exit Error Report Code

(See notes above)

✻59

If the system is not disarmed before the end of the entry delay

mentioned above, and an entry/exit or interior zone is still open,

an “exit alarm” message will be sent to the central station if an

Exit Error report code is selected in this field. The keypad will

display “EA (EXIT ALARM),” and the alarm sounding will

continue until the system is disarmed (or timeout occurs).

An Exit Alarm condition will also result if a fault occurs in an

exit or interior zone within 2 minutes following the end of the

exit delay, and an “Exit Alarm” message will be sent to the

central station.

If Contact ID® format has been programmed, the message will

contain the zone number and error code 374 (Trouble–Exit

Error). If 4+2 format is used, the digit entered in this field will

be sent followed by the second digit of the programmed alarm

code for that zone. If 3+1 or 4+1 format is used, only the digit

entered in this field will be sent. This message will go to the

primary phone no. Under any of these conditions, no restore

message will be sent.

If “0” is entered in this field, no special message will be sent,

only the regular alarm and alarm restore code for the zone.

This will be sent if a zone goes into trouble.

Trouble Report Code

✻60

(See notes above)

This will be sent when a zone is manually bypassed.

Bypass Report Code

✻61

(See notes above)

Timing of this report is random with up to a 4-hour delay. If AC

restores before the report goes out, there is no AC restore report.

AC Loss Report Code

✻62

(See notes above)

- 24 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

This will be sent when a low battery condition exists in the

system’s standby battery.

Low Battery Report Code

(See notes above)

✻63

✻64

✻65

This is sent periodically to test that the communicator and

phone lines are operational (frequency of report is selected in

field 51).

Test Report Code

(See notes above)

✻

This is sent upon disarming of the system. 2nd digit = user

number, if expanded or 4+2 reporting is selected.

Open Report Code

(See notes above)

This option allows for independent programming of AWAY and

STAY reports. 2nd digit of report is user number if expanded or

4+2 reporting is selected.

Arm AWAY/STAY Report Code

(See notes above)

✻66

NOTE: OPEN reports are not sent if the associated closing

report is not enabled.

This is sent in the event that a wireless transmitter low battery

condition exists.

RF transmitter Low Batt. Report Code

(See notes above)

Cancel Report Code

✻67

✻68

This is sent upon disarming of the system after an alarm

condition was reported.

(See notes above)

✻

RESTORE REPORT CODES ( 70– 76)

Sent when the zone that caused an alarm is restored to its non-

faulted condition. 2nd digit is automatically sent as the 2nd digit

of the zone alarm report code programmed in field 56, if

Alarm Restore Report Code, 1st Digit

(See notes above)

✻70

✻

expanded or 4+2 reporting is selected.

Sent when a trouble in a zone is restored.

Trouble Restore Report Code

(See notes above)

✻71

Sent when a zone that has been bypassed is unbypassed.

Bypass Restore Report Code

(See notes above)

✻72

Sent when AC power has been restored after an AC power

outage.

AC Restore Report Code

(See notes above)

✻73

Sent when a system low battery condition is restored to normal.

Low Battery Restore Report Code

(See notes above)

✻74

Sent when a transmitter that previously sent in a “low battery” message

has sent a message indicating it no longer has a low battery condition.

RF Transmitter Low Batt. Restore Code

(See notes above)

✻75

Sent when the test mode is exited. A restore code entered here will cause

a restore message to be sent when Test mode is exited.

Test Restore Report Code

(See notes above)

✻76

- 25 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

To ensure that the LYNXR-I properly transmits its reports to the Central Station via the proper channel you must program a

Primary Phone Number in Field *41 and/or activate/deactivate the LRR/IP Communications Module in Field *55.

The 15-Second Dialer Delay (Burglary), programmed in Field in *50 is independent of the delay selected in Field *77 and

applies to both telephone and communications device.

✻

DYNAMIC SIGNALING DELAY/DYNAMIC SIGNALING PRIORITY FIELD 77

Two report channels are used by the LYNXR-I to support the LRR/IP communications device and dynamic signaling. For

the primary channel the device can communicate via LRR, Cellular GSM, or Internet (IP). Secondary phone is not

affected by dynamic signaling scheme. Two programming options are used to define dynamic signaling behavior. Field

*55 is used to enable/disable the LRR/IP communications device and allows it to supervise the communications module.

The two-digit option programmed in Field *77 defines how dynamic signaling will function. The Dynamic signaling

options are shown below:

Enable/Disable

Device (Field *55)

0 = Disable

Dynamic Signaling Delay/Dynamic Signaling

(Field *77)

1st Entry

Enter Any Digit

2nd Entry

Reporting Option

Primary Phone only

Report is sent to Primary phone with No Dynamic Signaling

Delay

Enter “0”

1 = Enable

1st Entry

LRR/IP Communications Device only

* = enter any non zero digit as a first entry

2nd Entry

2 = LRR/IP reporting only

Report sent to communications device with No Delay

1st Entry

Redundant reports to both channels

Report independently goes to the Primary phone and LRR/IP

communications device with No Delay

0 = Redundant reporting on dialer and comm. device

2nd Entry

* = enter any number as a second entry

1st Entry

* = enter a delay for the first entry

2nd Entry

Primary Phone is the preferred channel

First report is sent to the primary phone. If primary phone fails to

deliver report within the delay window defined in *77 all following

reports go to both primary phone and communications device

with no delay. When report goes through the primary phone,

LYNXR-I stops reporting to communications device.

0 = Primary Dialer is the preferred channel

Note: The delay must be set to at least 30 seconds if Remote

Phone Control and/or AAV is enabled.

1 = Enable

1st Entry

* = Enter any delay for the first entry

2nd Entry

LRR/IP Communications Device is the preferred channel

First report is sent to the communications device. If device fails to

deliver report within to deliver report within the time window

defined in *77 all following reports go to both LRR/IP device and

primary phone with no delay. When report goes through the

LRR/IP device LYNXR-I stops reporting to primary phone.

1 = LRR/IP is the preferred channel

Note: If the LRR/IP communications device is selected as the preferred channel option and the LYNXR-I detects a communication failure or

supervision failure, reports will be sent to the Primary Phone without any delay.

Intended for use with LRR/IP communication device reporting.

This field’s 1st Entry allows you select the time the panel will

wait for acknowledgment from the first reporting destination

(preferred channel) before it attempts to send a message to the

second destination. This delay is per message. The 2nd entry

allows you to select the preferred reporting channel.

Notes: (1) You must also enable/disable LRR/IP Device in field *55.

(2) If Remote Phone Access is enabled, and Primary Phone is

used as a Preferred Channel, Dynamic Signaling Delay

should be at least 30 sec in order to prevent duplicate

reports.

Dynamic Signaling Delay/ Dynamic

Signaling Priority

✻77

1st Entry (delay before switching Central Station

reporting path)

0 = Redundant reporting

on dialer and LRR/IP

communications

device

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

4 = 60 seconds

5 = 75 seconds

6 = 90 seconds

7 = 105 seconds

8 = 120 seconds

9 = 135 seconds

#10 = 150 seconds

#11 = 165 seconds

#12 = 180 seconds

#13 = 195 seconds

#14 = 210 seconds

#15 = 225 seconds

(3) For UL installations Dynamic Signaling Delay cannot exceed

15 sec. If Primary Phone is used as a Preferred Channel,

duplicate reports may sent.

1st Entry

Enables Dynamic Signaling Delay. The entry of digits 1-9 or #10-

#15 will control the time-out period the panel will wait for an

acknowledgment from the first reporting destination. Delays can

be selected from 0 to 225 seconds, in 15-second increments. If 0

is entered, the control panel will send redundant reports to both

Primary Dialer and the LRR/IP communications device.

2nd Entry

0 = Primary Dialer Preferred Channel

1 = LRR/IP Preferred Channel

2 = LRR/IP reporting only

The second entry determines the Dynamic Signaling Priority.

The alternate Central Station communication path will be

initiated After the time-out period.

- 26 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

If “0” is entered, user can define a macro function for the AUX key. See

user manual for description of the use of this key.

AUX Function/1-Button Paging

0 = Aux key performs defined function

(macro)

1 = Aux key sends predefined message to

pager or a voice message to Follow Me

system phone number

✻87

✻88

If “1” is entered, you must also select an option in field ✻49. The options

are 6-9 for the pager or 10-13 for the follow me system announcement.

The actual pager message is 999-9999. Note that the hyphen may not be

displayed, depending on the pager service. The manual follow me system

announcement is a repeatable “System, System…..”.

Note: A macro cannot be run from the Test mode.

If entered, these digits will appear in front of the 7-digit pager message

sent by the control (either upon a system event or upon pressing the AUX

key [if programmed for paging]), and during latch key report (if enabled

during scheduling). These digits can consist of a PIN number, account

number, pauses or special digits needed by the pager (these types of

characters are not displayed), or any other characters the user chooses

that will be displayed (e.g., using a character code to distinguish between

control panel messages and other pager messages).

Pager Characters

Enter up to 16 digits that will appear in front of the 7-

digit pager message.

Enter [#] + [11] for “*”

Enter [#] + [12] for “#”

Enter [#] + [13] for 2-second pause

Note: Verify that the pager supports [*] and [#] characters

before using them. Some pagers require an additional

delay [pause] in order to receive the entire message.

✻

You do not need to fill all 16 digits. Press [ ] + next field number to exit

the field. To clear the field, press 88

✻

✻.

✻

See field 87 to select the AUX key Paging feature. See field 49, which

must have an option 6-9 selected to enable paging messages, for

description of the pager message.

✻

If an Event Logging selection is made in field 90, a message can be sent

Event Log 80% Full Report Code

✻89

✻90

to the central station receiver when the log is 80% full. If the log becomes

full, a new message will overwrite the oldest message in the log.

Note: All control and readout from the log, aside from the selection made

(See notes above)

✻

by the installer in field 90, is accomplished via the downloader.

Example: To select “Alarm/Alarm Restore” and “Open/Close,” enter 9 (1 +

8); to select all events, enter #15.

Event Logging Options

0 = No event logging

1 = log Alarm/Alarm Restore

2 = log Trouble/Trouble Restore

4 = log Bypass/Bypass Restore

8 = log Open/Close

Default “3” = alarm/alarm restore (1) plus trouble/trouble restore (2).

The system has the ability to record various events in a history log (84-

event capacity). The types of events to be logged can be selected as

indicated. At any time, the downloader operator can then upload the log

and view or print out all or selected categories of the log. The log can also

be cleared by the download operator.

x = log combination of events (add value of entries)

The display/printout at the central station will show the date, time, event,

and description of the occurrences.

Note: System messages are logged when any non-zero selection is made.

This option is used to enable the Audio Alarm Verification and/or the

Remote Phone Control features.

Audio Alarm Verification (AAV)/Remote

Phone Control

0 = none

1 = AAV and remote phone control

2 = remote phone control only

4 = AAV only

✻91

Notes: (1) In order to activate the Remote Phone Control feature and

defeat an answering machine, ensure that the correct ring

✻

detection count (“15”) has been programmed in field 95.

(2) Remote phone session will be terminated if a report must be

sent.

Notes:(1) For UL installations Audio Alarm Verification cannot

be used.

(3) If an alarm will be reported to primary and secondary phone

numbers, AAV can only function via the secondary number.

(2) Audio Alarm Verification will only function when

Contact ID® is selected.

✻

(4) If an alarm will be reported to a pager (6-8 in field 49), or to

✻

follow me phone number (10-12 in field 49) AAV cannot be

(3) AAV and Remote Phone Control features can only

be used if the central station or remote phone

supports DTMF commands.

used.

This option can be used to limit the number of messages (alarm & alarm

restore reports) sent to the central station in an armed period.

UL installations: must be 1 (unlimited reports)

Number of Reports In Armed Period

0 = reports limited to a total of 10

1 = unlimited number of reports

Flexible Callback

0 = no flexible callback

1 = last digit flexible

2 = last 2 digits flexible

3 = last 3 digits flexible

✻92

✻93

Note: This feature only applies to telephone downloading

If enabled, the control will ignore the last 1, 2, or 3 digits of the

✻

programmed callback number (field 94) during a single download session.

This allows the download operator to temporarily change the callback

phone number by the number of digits selected, which allows the control to

call back similar, but different numbers during a single session. For

example, if downloading to a large number of controls, the operator can

command the controls to call back phone numbers 555-1111, 555-1112, 555-

1113, etc., thus spreading the communications among several computers.

- 27 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Data Field Descriptions

✻

DOWNLOAD INFORMATION ( 94, 95)

This is the phone number the control will use to call back the downloading

computer.

Download Call Back Phone Number

Enter up to 20 digits as follows: 0–9, # +11 for “*”, #

+ 12 for “#”, # + 13 for a pause.

✻94

✻

Do not fill unused spaces. End field by pressing . To clear entries from

✻

field, press 94

Enter “15” to select defeat answering machine mode. If an

answering machine is on the premises, you need to dial the

premises and hang up on the first ring. Wait at least five (5)

seconds (but no more than 22 seconds) and dial the premises

phone number again. The control will pick up and announce

“SYSTEM ENTER CODE” every three seconds.

Ring Detection Count For Downloading/

Remote Phone Control

0 = disable station initiated download and remote

✻95

phone

1-14 = number of rings before control picks up phone

line

15 = defeat answering machine

Note: To enter a number higher than 9 you must first press the [#] key.

OTHER PROGRAMMING COMMANDS

✻

ENHANCED ZONE PROGRAMMING MODE

✻

Interactive menu mode used for programming zone attributes and report codes. Refer to the 56

Enhanced Zone Programming Mode section for procedure.

✻

DEVICE PROGRAMMING MENU MODE

Interactive menu mode for programming Powerline Carrier Devices. Refer to the 80 Device

Programming Menu Mode section for detailed procedure.

✻

ZONE LISTS MENU MODE

Interactive menu mode for programming zone lists for Powerline Carrier Devices. Refer to the 81

Zone List Menu Mode section for detailed procedure.

✻

ENHANCED SEQUENTIAL MODE

Interactive menu mode used to enter RF transmitter serial numbers. Refer to the 83 Enhanced

Sequential Mode section for detailed procedure.

✻

ASSIGN ZONE VOICE DESCRIPTORS

Interactive menu mode used to assign descriptors to each zone. These descriptors will be announced

whenever the system announces an event involving a zone.

✻

RECORD CUSTOM VOICE DESCRIPTORS

Interactive menu mode used to record custom descriptors for use with each zone.

INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. NO. FOR

DOWNLOADING

✻

Pressing 96 initializes the system for downloading.

✻

SET ALL PROGRAM FIELDS TO 1 OF 4 SETS OF DEFAULT VALUES

See Default Tables at the end of this manual.

EXITS PROGRAMMING MODE

Prevents re-entry by: Installer Code + 8 + 0 + 0; allows re-entry only by Power-up, then [ ] and [#].

✻

EXITS PROGRAMMING MODE

✻

Allows re-entry to program mode by: Installer Code + 8 + 0 + 0; or by Power-up, then [ ] and [#].

- 28 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

56 Enhanced Zone Programming Mode

This is an interactive menu mode that is used to program zone numbers, zone types, alarm and report codes,

and to identify the type of loop input device. This mode can also be used for entering 5800 Series transmitter

serial numbers.

Note: There are two methods for entering transmitter serial numbers. The first method is by using ✻56 Enhanced Zone Programming mode

(described below). The second method is by using ✻83 Enhanced Sequential Mode. Note that the ✻83 Enhanced Sequential Mode

requires that all zone information first be entered using ✻56 Enhanced Zone Programming mode.

You must refer to these instructions or to the Program Form while programming the system because the

keypad display does not show prompt titles. Instead, prompts are indicated by a number/letter combination.

The prompts for ✻56 are as follows:

A 02

Zone Number----------------------- for entering the zone number

Zone Type ------------------------- for entering zone type

Report Code------------------------- for entering the zone’s report code

Input Type ------------------------- for entering the transmitter’s input type

Loop Number----------------------- for entering the transmitter loop number

Delete Serial Number? ---------- for deleting existing serial number

Enroll Mode? ----------------------- selects serial number enroll mode

Serial Number --------------------- for entering transmitter’s serial number

Voice Descriptor?------------------ selects voice descriptor mode

Descriptor 1------------------------- for entering first descriptor word

Descriptor 2------------------------- for entering second descriptor word

Descriptor 3------------------------- for entering third descriptor word

- 29 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

56 Enhanced Zone Programming Mode

While in Program mode, press

✻56 to enter Zone Programming Menu Mode.

Refer to the zone assignment table for ✻56 on the separate programming form.

The following explains the ✻56 prompts in detail. The left two columns identify the prompts and list the

available entries for each. The right-most column provides a further explanation of the entries.

Note:

You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow you to clearly hear

feedback announcements or system beeps.

Enter the 2-digit zone number to be programmed and the Voice

Descriptor for the selected zone number will be announced, if it is

programmed. Press [✻] to advance.

Zone number

02-41, 95, 96, 99 = Zone number

[✻] = continue

00 = exit Zone Programming mode

• Zones 02-25 = RF zones (only)

• Zones 26-41 = Button zones (only)

• Zone 92 = Duress

• Zones 95, 96, 99 = Panic zones

Pressing 00 exits mode, upon which the prompt “56” blinks, indicating

the mode is inactive. Press [✻] + any field number to go to that field.

Each zone must be assigned to a zone type, which defines the way in

which the system responds to faults in that zone. Enter the 2-digit zone

type for this zone as follows:

Zone type

00-24 = zone type

b zt

[✻] = continue

[#] = return to previous prompt

00 = Not Used

08 = 24 Hr Aux

01 = Entry/Exit #1

02 = Entry/Exit #2

03 = Perimeter

04 = Interior Follower

05 = Trouble Day/Alarm Night

06 = 24 Hr Silent

09 = Fire without verify

10 = Interior w/Delay

20 = Arm–Stay

21 = Arm–Away

22 = Disarm

23 = No Alarm Response

24 = Silent Burglary

Note: If 00 is accepted as a zone type, save the 00

zone type and advance to the confirm delete

prompt (F).

07 = 24 Hr Audible

The report code consists of 2 hexadecimal digits, each in turn consisting

of 2 numerical digits. For example, for a report code of "3C", enter [0][3]

for "3" and [1][2] for "C".

If this isZone 95, 96 or 99, the system skips to the VOICE

DESCRIPTOR prompt (1C).

Report code

Enter the report code for this zone.

[✻] = continue

C rc

[#] = return to previous prompt

Enter the input type for the transmitter assigned to this zone. Refer to

the transmitter’s instructions for input types of each transmitter.

Input type

3 =RF (supervised RF) – sends periodic

check-in signals, faults, restore and low

Note: Zones 2-25 should be assigned Input Type 3 or 4 . Zones 26-41

battery signals

should be assigned Input Type 5 only.

Note: RF type transmitters must remain within range

of the receiver, otherwise a supervision failure

signal will occur.

4 = UR (unsupervised RF) – sends same as

“RF” type, but control does not supervise

the check-in signals

5 = BR (button type) – sends only fault and low

battery signals; does not send restores or

check-in signals

Note UR and BR type transmitters may be carried off

premises (out of range without causing a

supervision failure.

[✻] = continue

[#] = return to previous prompt

- 30 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

56 Enhanced Zone Programming Mode

This prompt can be used to enroll loop number and serial number via

Loop number or Loop and Serial

RF transmission or the loop number can be enrolled manually. If

using the RF Learning Mode, there is no need to manually enter a

loop number. Proceed directly to RF Learning

number (if using RF Learning)

1-4 = loop number for the zone of the transmitter

being entered.

0 + [✻] = continue to DELETE ZONE

PARAMETERS CONFIRMATION prompt

(F)

[✻] = continue to the ENROLL MODE prompt

(1A) if not entered, or VOICE DESCRIPTOR

prompt if already entered

Notes: (1) BR type devices cannot be enrolled by using UR or RF

type. Likewise, UR or RF type devices cannot be enrolled

by using a BR type device. There is a 52-second time-out

for RF enrolling. At the end of the time-out, the system

returns to the INPUT TYPE prompt (d). If enrolled, loop

number and “L” are displayed.

(2) Once encrypted (high-security) devices have been enrolled

they must be activated. Refer to the device’s Installation

Instructions to activate the High-Security Mode. RF

Learning - Two (2) transmissions (2 key depressions) at

least 5 seconds apart will be required for BR type devices

(device type 5). Two beeps will sound after the second

transmission, confirming that the loop number and serial

number have been learned.

[#] = return to previous prompt

For all other device types, four (4) transmissions are required (fault,

restore and fault, restore). A single beep will sound after the second

transmission confirming that the loop and serial number have been

captured. Following the fourth transmission the system will confirm

that the loop number and serial number have been learned and

announce the Voice Descriptor for the zone, if it is programmed,

followed by two beeps.

Press [✻] to continue.

Manual Entry - Enter the desired loop number and press [✻] to

continue (see the transmitter’s Installation Instructions for specific

loop designations).

Note: The loop number can be changed even if the zone has already

been entered. Care should be taken when using this feature as

it has the capability to make zones inoperable by creating a

mismatch of a working serial number/loop number

combination. This should be re-confirmed if the loop number is

changed.

“L” indicates that the zone’s serial number has already been enrolled.

This function deletes either the serial number or all zone information

that is programmed for the zone.

If “00” was entered in the zone type, the confirmation of the delete

request will delete all information associated with the zone currently

being programmed.

Delete zone parameters confirmation

0 = discard the delete request

1 = confirm requested delete

Note: If 00 was entered as a zone type in prompt (b), 00

will be retained and system will advance to

prompt (1C).

If “0” was entered in the loop number, the confirmation of the delete

request will delete the serial number of to the zone currently being

programmed.

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

56 Enhanced Zone Programming Mode

If “L” is displayed, the serial number for this transmitter has already

Enroll mode

been entered. It may, however, still be viewed, confirmed (only if in

listen mode), or deleted.

0 = advance to the VOICE DESCRIPTOR

prompt (1C).

IA LC

Note: This will save all zone parameters.

View serial number

Enter “3”. Each digit will be redisplayed, and the keypad will beep once

for digits 1-6, and three times for the last digit.

1 = enter now and proceed to SERIAL

NUMBER prompt (1b).

Note: Not applicable if the serial number is already

present.

Confirm serial number

The serial number/loop number combination can be confirmed after one

transmission from a BR type device or two transmissions (fault and

restore) from a UR or RF type device. If a transmission is received that

matches the serial number and loop number entered, the system will

confirm the reception by announcing the Voice Descriptor for the zone,

if it is programmed, followed by three beeps, and a “C” will appear on

the display indicating the received serial number and loop number

have been confirmed. No further transmissions will be received.

2 = copy the last serial number entered into

local ram.

Note: If this is the 1st zone, none will be in the buffer

and the panel will emit a long tone. Not valid if

serial number is already present.

3 = view existing serial number.

Note: Only if “L” is displayed. If “L” is not displayed,

panel will emit a long beep.

Delete serial number

The serial number can be deleted by entering “9”.

9 = advance to F; delete existing serial

number.

Note: Only if “L” is displayed. If “L” is not displayed,

panel will emit a long beep.

If “L” is not displayed, the serial number for this transmitter has not

been previously entered. You may enter the serial number manually,

copy the previous serial number, return to Prompt (E) or enter the

serial number later using the ✻83 Enhanced Sequential Mode.

[✻] = advance to the VOICE DESCRIPTOR

prompt (1C). This will save all zone

parameters.

Manual entry

Enter "1" to advance to Serial number prompt (1b).

Copy the previous serial number

Enter “2” to copy the previous serial number entered.

Return to Prompt (E)

[#] = return to the LOOP NUMBER prompt (E).

Note: In order for all entered parameters to be

accepted, you must advance to the VOICE

DESCRIPTOR prompt (1C).

Enter “#” to return to Loop Number prompt (E).

Enter transmitter later

Enter “0” or “✻” if you wish to enter the transmitter later, using the

✻83 Enhanced Sequential Mode described later in this manual.

Notes: (1) The panel will listen only when it is in the idle loop waiting

for key entry and a serial number has been entered. If a key

is entered, the function must be completed and the panel

will listen again.

(2)A long beep indicates illegal entry or duplicate serial number/loop

entry

In this mode, the transmitter serial numbers can only be entered

manually.

Serial number

Enter the transmitter’s 7-digit serial number.

[#] = return to prompt 1A and reject any serial

numbers entries that have been made.

[✻] = return to prompt 1A, (if a valid serial

number has been entered, the "L" is

displayed and the serial number will be

copied into EEROM from the last serial

entered into the buffer.)

Enter the 7-digit serial number printed on the transmitter. If an

incorrect digit is entered, press the [#] key to backup to prompt (1A)

and start over. When all 7 digits are entered, press the [✻] key.

If 52 seconds passes and no entry has been made, the system returns

to prompt (1A).

Notes: (1) If the serial and loop number combination is already

present the keypad will emit a single long beep and the

system will return to the (1A) prompt and “L” will be

displayed.

Note: This prompt can be used only to manually

enroll a serial number. RF enrollment will be

rejected and the current zone descriptor will be

announced, followed by a single long beep

and the system will return to prompt (1A).

(2) If less than 7 digits have been entered, the keypad will

emit a single long beep and return to the (1A) prompt

without displaying the “L”.

(3) If more than 7 digits have been entered, the first 6 digits

will be saved along with the last digit that was entered

(entering 123456789 yields the serial number 1234569).

Each zone can have a voice descriptor of up to 3 words that will be

announced whenever the system announces status for that zone.

Voice descriptor

0 = skip to next zone (A)

1 = enter descriptor mode; existing descriptor

for this zone will be announced

- 32 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

56 Enhanced Zone Programming Mode

† see ✻84 Assign Zone Voice Descriptors section for vocabulary index

Descriptor 1

Enter [#] + 2-digit vocabulary index number† of

first descriptor word for this zone.

6 = accept word and advance to descriptor 2

(descriptor 2 will be announced)

8 = accept word and advance to next zone

(prompt A) – entire zone descriptor will be

announced

Use the [6] or [8] key to advance as described.

Id vi

IE vi

IF vi

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 1 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Press any other key to repeat the selected word.

† see ✻84 Assign Zone Voice Descriptors section for vocabulary index

Descriptor 2

Enter [#] + 2-digit vocabulary index number† of

second descriptor word for this zone.

6 = accept word and advance to descriptor 3

(descriptor 3 will be announced)

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 2 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

8 = accept word and advance to next zone

(prompt A) – entire zone descriptor will be

announced

Press any other key to repeat the selected word.

† see ✻84 Assign Zone Voice Descriptors section for vocabulary index

Descriptor 3

Enter [#] + 2-digit vocabulary index number† of

third descriptor word for this zone.

6 or 8 = accept word and advance to next zone

(prompt A) – entire zone descriptor will

be announced

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 3 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Press any other key to repeat the selected word.

- 33 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

80 Device Programming Menu Mode

Powerline Carrier devices (eg., X10 brand devices) are programmable switches that can be used to perform

many different functions. They can be used to turn lights on and off, control sounders, or for status

indications. In this system, each device must be programmed as to how to act (ACTION), when to activate

(START), and when to deactivate (STOP). Each of these is described below.

The control supports a total of 8 output devices.

The K10145X10 transformer sends signals from the control panel through the premises AC wiring to the

Powerline Carrier Devices (which are plugged into AC outlets). Devices plugged into Powerline Carrier

Devices can then be made to perform various functions in response to commands entered at the keypads in

the security system.

Powerline Carrier Devices have not been evaluated by UL.

Programming Options Defined

The following will help you understand the programming of output devices when using ✻80 and ✻81 modes.

ACTION The "ACTION" of the device is how the device will respond when it is activated by the

"START" programming. There are four different choices of actions:

• ACTIVATE for 2 SECONDS and then reset.

• ACTIVATE and REMAIN ACTIVATED until stopped by some other event.

• PULSE ON and OFF until stopped by some other event.

• NOT USED when the device is not used.

START

The "START" programming determines when and under what conditions the device will

be activated. The following START options are available:

Start by Event

1. Event is the condition (alarm, fault, trouble) that must occur to a zone or group of

zones (zone list) in order to activate the device. These conditions apply only when a

zone list is used. The different choices for "EVENT" are listed below and in the

“Programming Powerline Carrier Devices” paragraph that follows.

• ALARM

• FAULT

• TROUBLE

• NOT USED

Device activates upon any alarm in an assigned zone in the zone list.

Device activates upon any opening or short in an assigned zone in the zone list.

Device activates upon any trouble condition in an assigned zone in the zone list.

Device action is not dependent upon one of the above events.

2. A zone list is a group of zones to which the “EVENT” applies in order to activate a

particular device. Note that there are a total of 3 output device-related zone lists

that can be programmed in ✻81 menu mode; when the selected EVENT (alarm,

fault or trouble) occurs in any zone in the selected “Start” ZONE LIST (1, 2, or 3),

activation of the selected device will START.

Start by Zone Type or System Operation

• If a system operation, such as “DISARMING” or “ANY FIRE ALARM,” is to

activate the device, the appropriate choice would also be entered under the

“ZONE TYPE” option. “ZONE TYPE” is used independently of the

“EVENT/ZONE LIST” combination.

• If a "ZONE TYPE" is chosen, any zone of that response type going into alarm,

trouble, or fault will cause the device to activate as selected in "ACTION.” If the

same “ZONE TYPE” is also chosen for the STOP programming, any zone of that

type that restores will de-activate the device.

• If a "SYSTEM OPERATION" is chosen (e.g., End of Exit Time), that operation

will cause the device to activate as selected in "ACTION.” The different choices

for "ZONE TYPE" and "SYSTEM OPERATION" are listed in the “Start zone

type” paragraphs later in this section, and in the Programming Form.

- 34 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

80 Device Programming Menu Mode

The "STOP" programming determines when and under what conditions the device will be de-

STOP

activated. The following options are available:

Upon Restore of a Zone List

Restore Zone List: If a "ZONE LIST" is used as the “Stop” event, the device will de-activate when all the

zones in that list restore from a previous fault, trouble, or alarm condition. This will occur regardless of

what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" would normally only be

used when a "ZONE LIST" is used to start the device.

Upon a Zone Type or System Operation

Zone Type/System Operation: Instead of using a "RESTORE ZONE LIST," a specific zone (response) type or

system operation action can be selected to de-activate the device.

•

If a specific "ZONE TYPE" is chosen, any zone of that response type that restores from a previous alarm,

trouble, or fault condition will cause the device to de-activate.

•

If a "SYSTEM OPERATION" is chosen, that operation will cause the device to de-activate.

During normal system operation, any devices may be manually started by keypad entry of: Code* + [#]

+ 4 + “n;” or manually stopped by keypad entry of: Code* + [#] + 7 + “n,” where “n” = the device number to

be controlled.

* Code is required for devices 7 and 8. For devices 1-6, code is not required. See User Manual for more

information.

Programming Powerline Carrier Devices

While in program mode, press ✻80 to enter Output Device Menu Mode. This mode is used to program

all output devices used in the system. Refer to the output device table for ✻80 on the separate programming

form when programming output devices.

Note: The House ID of the Powerline Carrier Devices must be entered in data field ✻25.

The prompts for ✻80 are as follows:

Powerline Carrier Device Programming Main Menu prompt

A 01

Device Number --------- for entering the device number

Device Action------------ for defining the action the device will perform when active

Start Event Type------- for assigning the event type to start the action

Start Zone List---------- for assigning the zone list to start the action

Start Zone Type--------- for assigning the zone type to start the action

Stop Zone List----------- for assigning the zone list to stop the action

Stop Zone Type---------- for assigning the zone type to stop the action

- 35 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

80 Device Programming Menu Mode

The following explains these prompts in detail. The left two columns identify the prompts and list the

available entries. The right-most column provides a further explanation of the entries.

Note: Entering a number other than one specified will give unpredictable results.

Entering “1” advances to the next prompt below.

Entering “0” exits mode, upon which this prompt blinks, indicating

the mode is inactive.

Powerline Carrier Device

programming

0 = exit mode

1 = enter mode

Enter device numbers as 2-digit entries.

Device number

01-08 = device number to be programmed

[✻] = continue

00 = exit Device Programming mode

Enter the 1-digit action (0-3) for the device being programmed

(current action is displayed).

NOTES:

1. If “3” is entered (pulse), only up to 3 different devices can be

pulsed if one of the devices is a siren/horn (X10 Powerhouse

Security model SH10A). In addition, the siren/horn cannot be

manually activated using the lights on/lights off keypad

commands.

Device action

0 = No response

b aa

1 = Close for 2 seconds

2 = Close and Stay Closed

3 = Continuous Pulse on & off (1 sec ON, 1 sec

OFF)

[✻] = continue

[#] = return to previous prompt

2. If using an X10 Powerhouse Security SH10A siren:

• you must use device action “3.”

• you must change the device action default to “3” if using default

table 2 or 4

Enter the 1-digit event type (0-3) to activate the device being

programmed. A zone list must be used in conjunction with an event. If

a zone type/system operation is to be used instead of an event, enter

“0”.

Start event type

0 = Not used

1 = Alarm

2 = Fault

3 = Trouble

[✻] = continue

[#] = return to previous

prompt

If a zone list will be used to start the device action, enter the zone list

number at this prompt.

Start zone list

1-3 = zone list number (to be programmed in

field ✻81)

0 = zone list not used for this device

[✻] = continue

[#] = return to previous prompt

Start zone type

If a zone type or system operation will be used to start the device

action, enter the appropriate 2-digit code for the device being

programmed (see table that follows).

01-58 = zone type to start this device action

(select only those that are applicable)

00 = zone type not used for this device

[✻] = continue

Choices for zone types

00 = Not Used

01 = Entry/Exit #1 05 = Trouble Day/Alarm Night 09 = Fire

02 = Entry/Exit #2 06 = 24 Hr Silent 10 = Interior w/Delay

24 = Silent Burglary

Choices for system operation

04 = Interior Follower

08 = 24 Hr Aux

[#] = return to previous prompt

03 = Perimeter

07 = 24 Hr Audible

20 = Arming–Stay

33 = Any Alarm (except

zt 08 & 09)

42 = Sys. Batt. Low

21 = Arming–Away

22 = Disarm. (Code

+ OFF)

36 = At Bell Timeout**

38 = Chime

43 = Comm. Failure

52 = Kissoff

31 = End of Exit

Time

32 = Start of Entry

Time

39 = Any Fire Alarm

40 = Bypassing

58 = Duress

** Or at Disarming (which ever occurs earlier)

If a zone list will be used to STOP, or restore, the device action, enter

the zone list number 1, 2, or 3 (to be programmed in ✻81 mode). If not

used, enter “0”.

Stop zone list

1-3 = zone list to stop this device action

0 = zone list not used

[✻] = continue

[#] = return to previous prompt

If a zone type or system operation will be used to STOP the device

action, enter the appropriate 2-digit code (see the "ZT" choices listed

above). If not, enter 00.

The display then returns to the DEVICE NUMBER prompt (A) so

that you can enter the next device number to be programmed, or enter

[0][0] to end device programming.

Stop zone type

01-58 = zone type to start this device action

(select only those that are applicable)

00 = zone type not used for this device

[✻] = continue

IA zt

[#] = return to previous prompt

- 36 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

81 Zone List Menu Mode

While in Program mode, press

✻81 to enter Zone List Menu Mode. This mode is used to program zone

lists for output devices (programmed in ✻80 menu mode) or Chime-by-Zone in Zone List 3.

NOTES:

• Any list may include any or all of the systems zone numbers.

• A zone list can be assigned to more than one Powerline Carrier Device.

The prompts for *81 are as follows:

Zone List Programming-------------------- Main Menu prompt

A 01

Zone List Number --------------------------- for entering the zone list number to be programmed

Zone Entry to List --------------------------- for entering zones to the assigned zone list

Delete Entire List? -------------------------- for deleting the entire zone list and its contents

Delete Specific Zones From List?-------- Selects whether to delete zones or return to next zone

list number

Delete Zones----------------------------------- for deleting specific zones from the current zone list

The following explains these prompts in detail. The left two columns identify the prompts and list the

available entries. The right-most column provides a further explanation of the entries.

Notes: (1) Entering a number other than one specified will give unpredictable results.

(2) Do not assign zones with zone types 20, 21 or 22 to a zone list.

Pressing 1 advances to the next prompt below.

Pressing 0 exits mode, upon which this prompt blinks, indicating the

mode is inactive.

Zone list programming

0 = exit mode

1 = enter mode

Enter the Zone List Number 01, 02, or 03 to program (or 00 if no

zone lists are used).

Zone list number

01-03 = zone list number to be programmed

00 = exit Zone List mode

[✻] = continue

Enter each zone number to add to the zone list by first entering the

zone number, then the [✻] key (for example, 01✻ 02✻ 03✻). The

system will announce the Voice Descriptor for the selected zone, if it

is programmed. After all desired zones are enrolled, enter “00” to

advance.

Zone entry to list

01-41, 95, 96, 99 = zone numbers to add to zone

list

[✻] = accept zone number and enter the next zone

number

00 = accept zone number(s) and continue to next

prompt

To delete the zone list, enter “1”. All zones in the zone list will be

deleted automatically and programming will return to the ZONE

LIST NUMBER prompt.

Delete entire zone list?

0 = don’t delete; continue to next prompt

1 = delete the current zone list

To save the zone list or delete specific zones from the list, enter “0”.

To save the entire zone list, enter “0” and programming will return

to the ZONE LIST NUMBER prompt.

To delete a zone or zones in a zone list enter “1”.

Delete zones from list?

1 = continue to delete zones prompt

0 = don’t delete; continue to next zone list number

prompt (A….01)

[#] = return to zone list number prompt (A….01)

Delete zones

Enter each 2-digit zone number to be deleted from

the current zone list, followed by the [✻] key.

[✻] = delete zone and enter next zone to be

deleted

When deleting a zone(s) from the zone list, if the selected zone has a

Voice Descriptor programmed, upon deletion it will be announced as

a confirmation that it has been deleted. After all zones to be deleted

are entered, enter “00” to return to the ZONE LIST NUMBER

prompt so that another list can be programmed, if desired.

00 = delete zone and return to next zone list

number prompt (A….01) desired

- 37 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

83 Enhanced Sequential Mode

By using this mode, you can add, delete, or change the serial number of a transmitter in a zone, but retain

all other existing data that has been programmed for that zone. Note that the ✻83 Enhanced Sequential

mode requires that all zone information must first be entered using the ✻56 Enhanced Zone Programming

mode for all zones below zone number 26 (4 button key area).

Note: Any zone which already has a serial number learned in will not be accessible in ✻83Enhanced

Sequential mode!

Certain button-type transmitters have more than one button (e.g., 5804). Note that each button must be

assigned to a different zone. Similarly, the 5816 Transmitter has contact terminals and a reed switch for use

with a magnet. If using both, each must also be assigned to a different zone.

This means that the procedures that follow must be repeated for each button-type zone below zone number

26 or contact on the transmitter. Four zone button-type devices are held in zones 26 and above. They will be

started on boundaries of zones 26, 30, 34, and 38. These four zone button-type devices will have the option to

have all information entered in this field. One entry will set the loop number, report code, zone type, and

input device type for all 4 buttons, and a second entry will enter one serial number into four zones.

Note: Use this mode only after all other zone information has been programmed, including transmitter loop

numbers except for button-type zones over zone number 26. The panel will stop at zones 26, 30, 34

and 38 and zone data can be entered as a default here.

Enter Serial Number Sequential mode by pressing ✻83. The prompts for ✻83 are as follows:

A 02

Zone Number -----------------------for entering the zone number to be programmed

Enroll Mode -------------------------Selects method of serial number or viewing

Enroll Serial Number ------------for entering transmitter serial numbers

Delete Serial Number ------------for deleting existing serial numbers

The following explains these prompts in detail. The left two columns identify the prompts and list the

available entries. The right-most column provides a further explanation of the entries.

Notes: (1) Entry of a number other than one specified will give unpredictable results.

(2) In Enhanced Sequential Mode, 4 button type keys will always be enrolled simultaneously. They will be stopped at the 4 button

boundaries of 26, 30, 34 and 38, provided the zone is free of a serial number. If the first zone of the key has a serial number

enrolled, the remaining keys cannot be programmed in sequential mode. In addition, if the zone has not been set up (duplicate

loop, missing zone type, etc.) only entries 0 (skip to the next zone) and 4 (copy the key template) will be allowed.

(3) You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow you to clearly

hear feedback announcements or system beeps.

Enter the 2-digit zone number of the first transmitter to have its serial

number entered. The system will announce the Voice Descriptor for the

selected zone number, if it is programmed.

Zone number

Enter the 2-digit zone number.

[✻] = continue; system searches for zones not

yet entered (for zones 2 through 25 a zone

type must be entered), then advances to

ENROLL SERIAL NUMBER prompt “1b”

00 = exit Sequential mode

Press [✻] to continue. Starting with this zone number, the system will

search for the first transmitter that has all of the following attributes

pre-programmed in ✻56 ENHANCED ZONE PROGRAMMING:

Make sure that the appropriate input type was selected in ✻56

(RF, UR, or BR programmed)

Make sure that the appropriate loop number was selected in ✻56.

No serial number programmed

Zone type

If the first zone number entered does not have one or more of the above

attributes, the system will search its database for the first zone that

does, and will display it at the enroll SERIAL NUMBER prompt (1b).

Pressing 00 exits mode, upon which the prompt “83” blinks, indicating

the mode is inactive.

Note: Two exceptions to the requirement above exist for keys. Four

zone button type devices (zone numbers 26, 30, 34, and 38) will

be stopped only if there are no serial numbers enrolled in all 4

zones of the key, regardless of the attributes that have been

entered. In addition, zone types are not required to be present.

In this case, 1A, Option 4 must be selected prior to “Learn”.

- 38 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

83 Enhanced Sequential Mode

Note:If “L” is displayed, the serial number for this transmitter

Enroll mode

has already been entered, however, it may still be

confirmed, viewed or deleted.

0 = advance to next zone to be enrolled

1 = enter now and proceed to SERIAL NUMBER

prompt (1b).

If the transmitter’s serial number has not been previously entered, you

may enter the enroll serial number mode (1A) by entering “1”, or copy

the last serial number that was entered by entering “2”.

For 4 button keys (zones 26-29, 30-33, 34-37, &

38-41) the serial number will be enrolled to all four

buttons.

If enrolling a key, the panel will emit a long beep

when entering a 1 to indicate that the present key

IA LC

If the transmitter’s serial number has been previously entered, you

may, view the present serial number by entering “3”. If view is selected

each digit will be re-displayed, and the keypad will beep once for digits

1-6, and three times for the last digit. Once the serial number has been

entered by either selecting a “1” or a “2”, you will return to this prompt

with the “L” on the display. The serial number/loop number

combination that was entered can be confirmed by getting two

transmissions (fault and restore) from the RF or UR device or one

transmission from the BR device. If a transmission is received that

matches the serial number and loop number entered, the system will

announce the Voice Descriptor for the loop followed by three beeps, and

a “C” will be displayed indicating that the received serial number and

loop number transmission has been confirmed to match. No further

transmissions will be received. When confirming a 4 button key, only

the serial number is confirmed, since it assumed that all loops are

used. Pressing any key will allow a confirmation.

set up is invalid.

Notes:(1) A valid template or key has 4 existing zones,

each with a zone type, unique loop number.

(2) If the display automatically advances to "1A"

rather than "1b" the configuration of the key

is not valid. At that point copy template,

skip, or return are the only legal entries.

2 = copy the previous serial number entry from

the buffer.

Notes:(1) Before you can copy a serial number you

must first enter a serial number. If no serial

is stored in the buffer and a copy is

attempted the panel will emit a long beep

indicating an invalid operation.

(2) Not applicable for 4 button key zones 26-29,

30-33, 34-37, & 38-41.

*Long beep indicates illegal entries, or duplicate serial

number/loop entry*

When the last zone has been entered, the display will remain on that

zone. To exit this mode and return to data field program mode, press 00

at the ZONE NUMBER prompt.

3 = view existing serial number.

Note: Only if “L” is displayed. If the “L” is not

displayed the panel will emit a long beep.

4 = copy the 4 button key template that has been

set in zone numbers 26-29 (all zone para-

meters except serial numbers). (Only valid on

zones 30-33, 34-37, & 38-41 that do not have

When all zones have been programmed, test each zone using the

system’s Test mode. Do not use the Transmitter ID Sniffer mode for

this, since it will only check for transmission of one zone on a particular

transmitter, and not the zones assigned to each additional loop.

serial numbers enrolled.)

For Zones 26-29, 30-33, 34-37, and 38-41 any loop can be used for RF

enrollment. If enrolling via RF, it will be confirmed without additional

transmissions.

Notes:(1) Template acceptance is indicated by two

beeps after copying.

(2) A single long beep emitted when copying a

indicates the template is not valid.

9 = delete existing serial. Go to the (1A) prompt.

For 4-button key, zones 26-29, 30-33, 34-37,

& 38-41 have serial numbers. Delete all four

at one time.

Note: Only if “L” is displayed. If the “L” is not

displayed the panel will emit a long beep.

[✻] = advance to next zone to be enrolled

[#] = return to previous prompt (A)

- 39 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

83 Enhanced Sequential Mode

This prompt can be used to enroll the transmitter serial number via

Serial number

RF transmission or manually. If using the RF Learning Mode there

is no need to manually enter a serial number. Proceed directly to RF

Learning. Upon entering the Serial Number mode, the Zone

Descriptors will be announced.

Enter transmitter’s 7- digit serial number via RF

learning or manually.

Ib zz

[#] = return to (1A) prompt and reject whatever

serial number entries have been made.

[✻] = return to (1A) prompt (if a valid serial

number has been enrolled, “L” is displayed

and the serial number will be copied into

EEROM and the last serial entered buffer.

Note: BR type devices can be enrolled only by transmission from BR

devices. Likewise, UR and RF devices can only be enrolled by

transmission from a UR or RF device

RF Learning - Two (2) transmissions (2 key depressions) at least

five seconds apart, will be required for BR type or four (4)

transmissions (fault, restore and fault, restore) for UR or RF type. If

the learned serial number has a different loop number than that

entered in ✻56 the system will announce the Voice Descriptor, if it

is programmed, followed by two beeps and will return to Prompt (1A)

and “L” will be displayed.

Note: For zones 26, 30, 34 and 38 only BR type

devices can be used.

If the loop number captured by RF transmission and that entered in

✻56 mode match, the system will announce the Voice Descriptor, if it

is programmed, followed by three beeps and return to Prompt (1A)

and “LC” will be displayed. No additional transmissions are needed

for confirmation.

Manual Entry - Enter the 7-digit serial number printed on the

transmitter. If you enter an incorrect digit, press the [#] key to

backup to prompt (1A) and start over. When all 7 digits are entered,

press the [✻] key. If less than 7 digits are entered, the keypad will

emit a single long beep and return to the (1A) prompt without

displaying the “L”.

If more than 7 digits have been entered, the first 6 digits will be

saved along with the last digit that was entered (entering 123456789

yields the serial number 1234569).

Note: If 52 seconds pass and no entry has been made, the system

returns to prompt (1A).

This function deletes only the serial number.

Delete serial number

0 = discard the delete request

1 = confirm requested delete

Note: Entering a “9” at prompt (1A) will cause the

panel to return to prompt (1A) regardless of the

confirmation answer.

Entering a “9” at prompt (1A). Confirmation of the delete request will

cause deletion of the serial number pertaining to the zone being

programmed.

Note: In Enhanced Sequential Learn Mode, 4 button type keys will always be learned simultaneously. They will be stopped at the 4 button

boundaries of 26, 30, 34 and 38, provided the zone is free of a serial number. If the first zone of the key has a serial number learned,

the remaining keys cannot be programmed in sequential learn mode. In addition, if the zone has not been set up (duplicate loop,

missing zone type, etc.) only entries 0 (skip to the next zone) and 4 (copy the key template) will be allowed.

- 40 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

84 Assign Zone Voice Descriptors

Use this mode to assign voice descriptors for each zone. These are the descriptors that are announced

when the system announces any event involving a zone number. Each descriptor can consist of up to

3 words. Press ✻84 while in Programming mode.

The prompts for ✻84 are as follows:

Voice Descriptors ----------------- Main Menu prompt

A 02

Zone Number----------------------- for entering the zone number to be programmed

Descriptor 1------------------------- for assigning the first word of this zone’s descriptor

Descriptor 2------------------------- for assigning the second word of this zone’s descriptor

Descriptor 3------------------------- for assigning the third word of this zone’s descriptor

The following explains these prompts in detail. The left two columns identify the prompts and list

the available entries. The right-most column provides a further explanation of the entries.

Note: Entering a number other than the one specified will give unpredictable results.

Pressing 1 advances to the next prompt below.

Pressing 0 exits mode, upon which this prompt blinks, indicating the

mode is inactive.

Assign zone voice descriptors

0 = exit mode

1 = enter mode

Enter the 2-digit zone number for which this descriptor is being

assigned, then press [✻]. The Voice Descriptor for the selected zone will

be announced, if it is programmed.

Zone number

[✻] = continue to next prompt (any existing

descriptors will be announced, then

descriptor 1 will be repeated)

00 = exit voice descriptor mode

Enter the first word of the descriptor for the selected zone.

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 1 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Descriptor 1

Enter [#] + 2-digit vocabulary index number of

first descriptor word for this zone.

6 = accept word and advance to descriptor 2

(descriptor 2 will be announced)

8 = accept word and advance to prompt (A) for

next zone. Press any other key to repeat the

selected word.

b vv

Enter the second word of the descriptor for the selected zone.

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 2 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Descriptor 2

Enter [#] + 2-digit vocabulary index number of

second descriptor word for this zone.

6 = accept word and advance to descriptor 3

(descriptor 3 will be announced)

8 = accept word and advance to prompt (A) for

next zone. Press any other key to repeat the

selected word.

Enter the last word of the descriptor for the selected zone.

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 3 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Descriptor 3

Enter [#] + 2-digit vocabulary index number of

third descriptor word for this zone.

6 or 8 = accept word and advance to prompt

(A) for next zone. Zone descriptor will

be announced. Press any other key to

repeat the selected word.

d vv

- 41 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

84 Assign Zone Voice Descriptor

VOICE VOCABULARY INDEX

00 ½ second pause

SYSTEM WORDS

AC LOSS

ARMED

AWAY

BYPASSED

CHIME

DISARMED

DISARM SYSTEM

NOW

EXIT NOW

FAULT

INSTANT

LOW BATTERY

NOT

READY TO ARM

STAY

48 GARAGE

49 GUEST ROOM

09 GUN

61 PATIO

62 POLICE

18 POOL

81 ZERO

86 ZONES

82 ALARM

32 ATTIC

29 1^ST

30 2^ND

31 3^RD

63 REAR

19 ROOM

50 HALL

01 BABY

33 BACK

34 BASEMENT

35 BATHROOM

36 BEDROOM

70 Custom Word #1

71 Custom Word #2

72 Custom Word #3

73 Custom Word #4

74 Custom Word #5

10 INSIDE

64 SECOND FLOOR

65 SEVEN

20 SHED

21 SHOP

66 SIDE

51 KITCHEN

99 Blank (for erasing

a previously

83 CHECK

67 SILENT POLICE

68 SIX

69 SLIDING

22 SMOKE

23 SOUTH

24 STORAGE

85 SYSTEM

11 LAUNDRY

52 LAUNDRY

ROOM

12 LIBRARY

13 LIVING

53 LIVING ROOM

programmed

word)

37 DELAY DOOR

38 DEN

02 DETECTOR

03 DINING

39 DINING ROOM

04 DOOR

40 DOWNSTAIRS

05 DRIVEWAY

14 MAIN

25 THIRD FLOOR

75 THREE

76 TRANSMITTER

77 TWO

15 MASTER

54 MASTER

BEDROOM

55 MEDICAL

84 MESSAGE

56 MOTION

DETECTOR

06 EAST

41 EIGHT

42 EMERGENCY

78 UPSTAIRS

26 UTILITY

79 UTILITY ROOM

43 FAMILY ROOM

87 FIRE

44 FIRE DETECTION

07 FIRST FLOOR

45 FIVE

08 FLOOR

46 FOUR

57 NINE

16 NORTH

58 NURSERY

27 WEST

80 WINDOW

59 OFFICE

60 ONE

17 OUTSIDE

28 YARD

47 FRONT

Notes: (1) If button type device is used to Arm Away, Arm Stay, and disarm the system it is recommended to assign

“Check” and “Zones” voice descriptors to each of the three zones. This will allow the system to announce

“Check Zones” “Low Battery” if the button device has a low battery.

(2) If a Wireless Keypad is being installed along with this system, not all the voice descriptors shown on this list can

be announced by keypad. (Refer to the Wireless Keypad documentation for further information).

- 42 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

✻

85 Record Custom Voice Descriptors

Use this mode to record up to 5 custom voice descriptors. Press ✻85 while in Programming mode.

Note: Entering a number other than one specified will give unpredictable results.

Entering “1” advances to the next prompt below.

Entering “0” exits mode, upon which this prompt blinks, indicating the

mode is inactive.

Assign custom voice descriptors

0 = exit mode

1 = enter mode

Record up to 5 custom words.

Custom descriptor number

Enter 7 + d + [✻]

Where d = 0-4, each representing custom

word 70, 71, 72, 73, or 74, respectively. Any

existing word will be announced.

Press [#] to start recorder. Begin speaking

immediately after the third beep.

Speak the desired word clearly near the

microphone. Recording stops after 1.5

seconds.

6 = accept word and ready to record next

descriptor prompt (A….7d)

[#] = re-record descriptor

00 = exit Record mode after pressing 6 to

accept word

Press any key to repeat the recorded word.

- 43 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Voice Prompt Programming

The LYNXR-I features a quick programming mode that allows you to program the system by responding to a

series of voice prompts. The Voice Prompt Programming Guide provides you with the information required

to use this feature.

Voice Prompt Programming Keypad Functions:

The keys shown below are used to navigate through the Voice Prompt Programming Feature.

1. ESCAPE/ OFF key: Used at any

time to exit the current menu and

return to the previous prompt.

2. ADD/ AWAY key: Used to add

sensors, or keys or save data when

ARMED

READY

entering phone or account

numbers.

OFF

ESCAPE

RECORD

VOLUME

PLAY

AWAY

ADD

3. DELETE/ STAY key: Used to

LIGHTS ON

TEST

BYPASS

STAY

delete a sensor when in the delete

Sensors Menu.

LIGHTS OFF

CODE

CHIME

DELETE

AUX

SELECT

STATUS

NO DELAY FUNCTION

4. SELECT/ AUX key: Used to

confirm a selection.

3 ↑ key: Used to scroll forward

01009-021-V1

through menu choices.

6. 6 ↓ key: Used to scroll backward

through menu choices.

7. FUNCTION/ # key: Used to repeat a voice prompt. (This function cannot be used while entering phone or account numbers.)

Notes: (1) Keying in any new command will terminate the active voice prompt.

(2) If an irrelevant command is entered LYNXR-I will generate a long rejection beep and repeat the previous voice prompt.

(3) Phone numbers and account numbers can be left blank by pressing the “ADD/ AWAY ” key without entering any data.

(4) LYNXR-I automatically saves phone and account number data once all available digits are entered.

ENTERING VOICE PROMPT PROGRAMMING

Power-up the control and enter the Installer Code

(4 1 1 2) + 8 8 8.

Follow the directions provided by each voice prompt to

make your selections.

Once you have entered into the Voice Prompt Programming

Mode the system will announce, “Programming, use

ARROWS to scroll choices, press SELECT to accept, press

ESCAPE to quit.”

The FUNCTION/ # key can be used to repeat a voice

prompt, as required.

When you have completed each programming procedure

the system will return to the Main Programming Menu.

Press the 6 ↓ or 3 ↑ keys to scroll through the voice

menu and follow the instructions provided.

EXITING VOICE PROMPT PROGRAMMING

The system will announce the following options:

“Add Sensors”

“Delete Sensors”

“First Central Station Phone Number”

“First Central Station Account Number”

“Second Central Station Phone Number”

“Second Central Station Account Number”

“Templates”

Once you have returned to the Main Programming Menu,

the system will announce, “Programming use ARROWS to

scroll choices, press SELECT to accept, press ESCAPE to

quit”.

Press ESCAPE/ OFF to exit Voice Prompt programming

mode once you have returned to the Main Programming

Menu.

“Expert Programming Mode”

- 44 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Voice Prompt Programming

Enter Voice Prompt Programming Mode: (Installer Code + 8 8 8). Follow the voice prompts to

advance to the selected item in the Main Programming Menu.

Add Sensors

Delete Sensors

First Central Station Phone Number

First Central Station Account Number

Second Central Station Phone Number Second Central Station Account Number

Templates Expert Programming Mode

Program each option as shown below. Use the 6 ↓ and 3 ↑ keys to scroll through the voice menu and follow the voice prompts to

program the LYNXR-I.

The LYNXR-I will enroll a sensor once the transmitter has been activated two times. The system will confirm the

enrollment following each subsequent activation of the same transmitter.

To Add a Door Sensor

(1) Delay Door Location

Front

Back

Side

Basement

Sliding

Hall

Garage

Kitchen

Patio

To add a Window, Motion Detector, or Fire Detection Sensor

(2) Sensor Type

(3) Sensor Location

(4) Location Modifiers

Window

Motion Detector

Fire Detection

Living room

Dining room

Bedroom

Bathroom

Nursery

Kitchen

Hall

Den

Upstairs

Downstairs

First

Second

Third

Second Floor

Front

Family Room

Guest Room

Laundry Room

Utility Room

Garage

Attic

Basement

Master Bedroom

Office

Upstairs

Rear

Side

- 45 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Voice Prompt Programming

To Delete Sensors

To Add an Emergency Pendant

(5) Pendant Type

Medical

Fire

Silent Police

Police

When adding wireless keys, wait 5 seconds between transmissions.

To Add a Wireless Key

LYNXR-I automatically saves phone and account number data once all available digits are entered.

To Add First Central Station Phone Number

All four digits of the Central Station Account number must be entered. If ten-digit format is selected, all

ten digits must be entered.

To Add First Central Station Account Number

- 46 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Voice Prompt Programming

All four digits of the Central Station Account number must be entered. If ten-digit format is selected, all

ten digits must be entered.

To Add Second Central Station Phone Number

To Add Second Central Station Account Number

Refer to the LYNXR-I Programming Default Tables to view the complete set of Template (default table)

selections.

To Program a Template (Default Table)

(6) Template selections

Template 1

Template 2

Template 3

Template 4

To Enter Expert Programming Mode

Once you have entered the Expert Programming Mode, the [ESCAPE] key can be used to return to the

Voice Prompt Programming mode.

- 47 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Remote Programming/Control (Downloading)

General Information

The control panel can be remotely programmed from an IBM-compatible Personal Computer (PC), a HAYES

Modem, and ADEMCO’s Compass Downloader for Windows (as specified below).

Downloading may only be performed if a technician is at the site.

Multiple security levels protect remote programming against compromise by attempts to defeat the system.

1. Security Code Handshake: An 8-digit download ID code must be matched between the Control and

downloader.

2. Site-Initiated Remote Programming: The installer or subscriber initiates the call from the subscriber

premises (by entering Installer Code + # + 1) while disarmed. All parameters can then be downloaded via

the phone lines using a personal computer.

3. Station-Initiated Remote Programming: The operator calls the site from your office to initiate the

download call. The Control hangs up and then calls back the PC via the preprogrammed telephone

number. The unit can then be uploaded, downloaded, or controlled from your office.

4. Telco Handoff: The installer or subscriber performs a download session on the call initiated from the

site or from local laptop computer (by entering Installer or Master Code + # + 1 at the control panel).

5. Data Encryption: Data passed between the PC and the Control is encrypted for security so that it is

very difficult for a foreign device tapped into the phone line to take over communication and substitute

system-compromising information.

Equipment required to download to a system at the premises

• An IBM PC compatible computer and appropriate interconnecting cables.

• Either a HAYES brand SMARTMODEM 1200 (Level 1.2 or higher external or Level 1.1 or higher [with 4

position DIP switch] internal style), a HAYES brand Optima 336 external, a HAYES brand Optima 24

Plus FAX96, or an Ademco CIA Modem.

• Compass Downloader for Windows (at revision level supporting LYNXR-I).

Initial Download: Enter Installer Code + # + 5. This sets field ✻95 to 4 rings, and system to “no call-back”

option. The download computer can then call the subscriber, make connection, and download all

programming data.

Flexible Callback: If enabled in field ✻93, the download operator can temporarily change the last 1, 2, or 3

digits (depending on selection) of the call back number. This allows the control to call back a computer other

than the one programmed, which may be helpful at times of high computer traffic. See field ✻93 for a full

description.

Remote Programming Information

If using Remote Programming, the LYNXR-I must be connected to the telephone line or to the Internet, as

applicable.

The downloading system can perform many functions when in communication with the Control. Besides

uploading and downloading, the status of the system can be observed and various commands can be

initiated, as follows:

• Arm the system in the away mode; disarm the system.

• Bypass a zone.

• Force the system to accept a new program download.

• Shut down communication functions (for nonpayment of monitoring fees in an owned system).

• Shut down all security system functions (for nonpayment for a leased system).

• Inhibit local keypad programming (prevents account takeover).

- 48 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Remote Programming/Control (Downloading)

• Command the system to upload a copy of its resident program to the office.

• Set the time

• View/Modify

• X10/ Scheduling

• Read: arming status, AC power status, lists of faulted zones, bypassed zones, zones currently in alarm,

zones currently in trouble, and RF sensors with low battery conditions; read control’s time.

Notes: (1) After the control and the PC have established valid communication, the keypad will become inactive and will display “CC.”

(2) The keypad will become active after the download communication is terminated.

(3) The detailed operation of the download functions is covered in the installation instructions for the Compass Downloader for

Windows.

Remote Programming Advisory Notes

• Keypad entries are ignored during the time interval stated above.

• A copy of the program downloaded may be printed using the IBM PC-compatible computer’s internal

report generator, when an optional printer is connected (consult your PC manual for proper printer and

connections).

• Program upload or download time is approximately one minute, fifteen seconds for a complete program.

- 49 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Operation

Security Codes

Installer Code

The installer programs the 4-digit Installer Code initially as part of the programming procedure. The

factory default Installer Code is 4-1-1-2, but may be changed in field ✻20.

The Installer Code is the only code that can enter Programming mode and also, in normal operation

mode, is used to enter the Master Code, which allows access to the normal functions of the system.

Master Code

In normal operation mode, the Installer Code is used to enter the 4-digit Master Security Code.

To enter/change the Master code by installer, using the keypad enter:

Installer Code + [CODE key] + [02] + desired 4-digit Master Code

To change the Master code by master, using the keypad enter:

Current Master Code + [CODE key] + [02] + new Master Code + new Master Code again

Secondary User Codes

In normal operation mode, the Master Security Code can be used to assign up to 6 secondary 4-digit security

codes, including a Babysitter Code and a Duress Code. The Master Code can also be used to remove

secondary codes from the system (individually).

To assign (or change) a secondary security code, using the keypad enter:

Master Code + [CODE key] + User # (03–08) + desired Secondary Code

The system will emit a single beep when each secondary code has been successfully entered.

To delete a secondary security code, using the keypad enter:

Master Code + [CODE key] + User # (03–08)

Security Code Notes

•

The Master and Secondary security codes permit access to the system for arming, disarming, etc.

The Installer Code can disarm the system only if it was used to arm it. In addition, the Installer Code cannot

disarm the system if it was armed by pressing and holding a Quick-Arm button.

•

The Babysitter Code (User Code No. 7) can disarm the system only if it was used to arm it. In addition, the

Babysitter Code cannot disarm the system if it was armed by pressing and holding a Quick-Arm button.

Duress code (User Code No. 8) sends a special code to the monitoring station when used to perform any system

operation.. Instruct users to be careful not to use this code for normal usage.

•

If a secondary code is inadvertently repeated for different users, the lower user number will take priority.

Opening/closing reports are sent for the Installer Code as No. 01, with the appropriate subscriber number. Master

Code and set of secondary user codes are sent as Nos. 02 and 03–08, respectively, in Contact ID® format (with the

appropriate user number); in 4+2, it is 1–8. Quick arming (and open/close executed by downloader) is reported as

user 00.

Panic Keys

There are three panic key pairs that, if programmed, can be used to manually initiate alarms and send a

report to the central station.

Each can be individually programmed for 24-hour silent, audible, personal or fire emergency responses. The

panic function is activated when both keys of the appropriate key pair are pressed at the same time.

The panic functions are identified by the system as follows:

Keys

Displayed as Zone

Important: For the silent panic functions

to be of practical value, the system must be

connected to a central station.

[1] & [✻]

[✻] & [#]

[3] & [#]

- 50 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Operation

Keypad Functions

The keypad allows the user to arm and disarm the system, and perform other system functions, such as

bypassing zones. Zone and system conditions (alarm, trouble, bypass) are displayed in the display window.

When an alarm occurs, keypad sounding and external sounding will occur, and the zone(s) in alarm will be

displayed on the keypad. Pressing any key will silence the keypad sounder for 10 seconds (only once).

Disarming the system will silence both keypad and external sounders. When the system is disarmed, any

zones that were in an alarm condition during the armed period will be displayed (memory of alarm). To

clear this display, simply repeat the disarm sequence (enter the security code and press the OFF key). The

keypad also features chime annunciation, and 3 panic key pairs for silent, audible, fire or personal

emergency alarms. These keys can notify the central station of an alarm condition, if that service is

connected. A summary of system functions is provided below for more detailed information refer to the

User’s Manual.

Security Functions (Empty boxes represent the user’s security code)

Checking system status: ........................ STATUS (high level messages); press STATUS again for secondary

messages

To arm in STAY mode: ..........................

STAY (or installer code + [3])

To restart exit delay: ............................... STAY (applies only if system is armed in Stay mode)

To arm in AWAY mode:...........................

To arm with NO DELAY:........................

AWAY (or installer code + [2])

AWAY or STAY

NO DELAY

To arm if Quick Arm is programmed:.. AWAY or STAY (hold down for at least 2 seconds)

To disarm the system and silence alarms:

OFF

Note: During Exit Delay or when an Alarm Condition exists the system can be disarmed by entering the User Code and entering

the OFF key is not required.

To bypass a zone(s): ................................

BYPASS + 2-digit zone number(s)

To turn Chime mode on or off: .............. FUNCTION

CHIME

Message Center

To record a message: ............................. FUNCTION

RECORD

To stop recording before end of 90 seconds: OFF

To play back a message:........................ FUNCTION

To skip a message: ................................ [✻]

To delete all messages:.......................... ^FUNCTION

Volume Control

PLAY

DELETE (during message replay)

To adjust message playback/system announcement volume: FUNCTION

VOLUME + [3] or [6]

To mute system announcements: ......... FUNCTION + VOLUME

OFF

To restore/unmute announcement & volume:

FUNCTION

VOLUME + [3] or [6]

Other Functions

To set the time and date: .......................

FUNCTION + [63]

To set the scheduling: .............................

To activate or deactivate X10 devices 1-6:

To activate or deactivate X10 devices 7 & 8:

To add a user code: .................................

To delete a user code (except Master Code):

To turn Test mode on: .............................

To turn Test mode off: ............................

FUNCTION + [64]

FUNCTION

LIGHTS ON or LIGHTS OFF + device number

FUNCTION + LIGHTS ON or LIGHTS OFF + dev. No.

*+ CODE + user number + user’s code (*master code)

*+ CODE + user number (* master code)

TEST

OFF

- 51 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Operation

To use the defined AUX function: Press and hold AUX key 2 secs (4 beeps) +

To define AUX function:

FUNCTION

AUX + action separated by + AUX terminated by + AUX +

AUX

To send message to pager: Press and hold AUX key 2 seconds (4 beeps)

To program Follow Me Announcement telephone number:

FUNCTION + [65]

NOTE

Speaker Phone Operation

To place a call or answer a call using the speaker phone: [#] + AUX

The ARMED and READY LEDs blink

alternately when the Speaker Phone is

active.

To flash (switch between two calls using call waiting): AUX

To hang up and exit speaker phone mode: OFF

To enable/disable (toggle) ringer: [#] + VOLUME

AUX

To return the keypad to telephone mode after disarming the system: [#] + AUX

Remote Phone Control Feature

The remote phone control feature, which must be enabled in field ✻91, allows the user to access the security

system from any off-site touch-tone telephone. The control will pick up the incoming call, based on the ring

count specified in field ✻95, and will announce “SYSTEM ENTER CODE” every three (3) seconds for the

next eight (8) seconds. During this period the panel will wait for a valid User Code to be entered. If a valid

User Code is not entered or the eight (8) second period expires a modem tone will be generated for remote

programming (Compass Downloading). If a valid User Code has been entered, the control will announce the

current system status and/or beeping sounds.

Quick Arm Note

The installer code and

babysitter code cannot

disarm the system if

armed by Quick Arm

method.

Keypad Functions

Remote Phone Control Feature

To remotely disarm system:

+ [1]

To remotely arm in AWAY mode:

To remotely arm in STAY mode:

+ [2]

+ [3]

To remotely arm in AWAY or STAY with no delay:

+ [2] or [3] + [0]

To remotely activate X10 devices 1-6: [#] + [4] + device no.

To remotely activate X10 devices 7 & 8:

+ [#] + [4] + device no.

To remotely deactivate X10 devices 1-6: [#] + [7] + device no.

To remotely deactivate X10 devices 7 & 8:

To remotely Bypass zones:

+ [#] + [7] + device no.

+ [6] + zone no.

+ [6] + [#]

To remotely activate Forced Bypass:

To remotely check system status: [✻]

To end remote phone control session: Hang Up or enter

+ [9]

- 52 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Operation

Audio alarm verification has not been evaluated by UL.

Audio Alarm Verification (Two-Way Voice Feature)

This feature allows the central station operator to listen, talk to or conduct a two-way conversation with an

individual(s) at the premises. It also assists the operator in gathering information about the nature and

location of the alarm that may be helpful in responding to police and fire departments. All LYNXR-I control

panels are capable of supporting the Two-Way Voice feature. The LYNXR-I does not make system

announcements when the Two-Way voice feature is active.

Activation

The LYNXR-I sends the “alarm message” followed by a “Listen-in-to-Follow message” (Contact ID® code

606) to the Central Station. The Listen-in-to-Follow message causes the Central Station’s digital receiver to

temporarily hold the phone line for approximately 1-minute. When the LYNXR-I receives the “kissoff” from

the central station, indicating that the alarm message has been received, the Two-Way Voice (AVM) feature

is activated in the (default) “Listen Mode” and sirens and keypad sounds are discontinued. The LYNXR-I

transmits a beep acknowledgment to the Central Station, once per second. The beep alternates between two

tones and indicates that the LYNXR-I is waiting for a session command from the Central Station operator.

Once a command is issued the beep acknowledgement is discontinued, however, if a command is not issued

within two minutes the system will “time out” and the call will be terminated.

Operator Commands

The Central Station operator begins the session, which last 5 minutes, by entering one of the valid AVM

commands shown in the table below. The session may be extended 5 minutes, without changing the

operating mode, by pressing the [7] key on the touch-tone phone. Selecting another operating mode also

resets the session an additional 5 minutes. During the last minute of the 5 minute, session, the LYNXR-I

generates two beeps every 30 seconds to alert the Central Station operator that the session is about to time

out. The Central Station operator may then extend the session by pressing the [7] key on the touch-tone

phone. If the session is not extended the phone line is disconnected, and the session is ended. Sessions may

be ended at any time by pressing the [9] key on the touch-tone phone. The AVM modes are described as

follows:

Note: When entering AVM commands make sure the Central Station receiver has been disconnected from the phone line,

otherwise AVM commands may not go through.

Key

Function

Talk Mode: Pressing the [1] key on the touch tone phone, enables one-way voice communication from the central station

to the violated premises, and allows the operator to talk communicate through the LYNXR-I speaker. In this mode the

ARMED (red) and READY (green) LEDs blink alternately.

VOX (Voice) Mode: Pressing the [2] key on the touch-tone phone, enables two-way voice communications between the central

station and the violated premises. In this mode the ARMED (red) and READY (green) LEDs blink alternately.

Listen Mode: Pressing the [3] key on the touch-tone phone, enables one-way audio from the violated premises to the central

station. The Listen Mode is the start up default mode of the voice feature and allows the operator to listen through the

LYNXR-I microphone. This mode does not affect the existing LED pattern.

Extends the session 5 minutes without changing its operating mode.

Ends the session and disconnects the phone line.

- 53 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Operation

“Follow Me” Reminder Feature

This feature allows the user to schedule a time driven message. When activated the system will dial a phone

number, that the installer programs in Field ✻46, and deliver a voice message (custom words 72, 73, and 74).

The LYNXR-I will immediately begin transmitting the voice message and will repeat the message for 45

seconds. Pressing any touch-tone key on the answering phone will acknowledge the message ending the

session and preventing the system from redialing the programmed number. Delivery of a reminder message

on the local LYNXR-I keypad will continue. If the message has timed out the system will redial the

programmed number a maximum of seven additional times or until it is acknowledged. Pressing any key on

the LYNXR-I keypad will terminate (acknowledge) both the follow me reminder and the local reminder

announcements.

Notes: (1) This feature is only supported if programmed in field ✻49.

(2) The follow me reminder will be terminated if any other event requires the system to dial out, or if an audible alarm has occurred,

however, delivery of the local schedule reminder message will continue.

“Follow Me” System Announcement Feature

This feature allows the LYNXR-I to deliver a voice system message to the secondary phone number

programmed by the installer. The LYNXR-I will first transmit reports to the Central Station and after

receiving its kiss-off the system will dial the secondary phone number and begin transmitting the voice

message. This message is a repeatable system status announcement. Like the Follow Me reminder, pressing

any key on the answering telephone or the local LYNXR-I keypad will terminate (acknowledge) the message.

The system will dial the secondary phone number a maximum of eight times. The Follow Me alarm

functions may be triggered by a variety of events depending upon the selections made during programming

in field ✻49.

Note: The follow me system announcement will be terminated if any other event requires the system to dial out or if an

audible alarm has occurred.

Powerline Carrier Devices (e.g. X10 devices)

If Powerline Carrier Devices are used, two keypad entries available to the user are included. They

can manually activate or deactivate the device(s) for starting or stopping some action, such as

turning lights on or off, etc.

These keypad entries are:

Security Code* + [#] + [4] + Device # activates (starts) that device.

Security Code* + [#] + [7] + Device # de-activates (stops) that device.

*Code is required for devices 7 and 8. Code is not required for devices 1-6.

Exit Error Alarm Displays

The system will display the following if programmed in Field *59.

Display

Meaning

will appear along with a zone indication if an exit or interior zone contained a

fault during closing at the time the exit delay ended (e.g., exit door left open),

but the system was disarmed during the entry delay time. The alarm

sounder and keypad sound continuously, but stop when the system is disarmed.

No message will be transmitted to the central station.

will appear along with a zone indication if an exit or interior zone contained a

fault during closing at the time the exit delay ended, but the system was NOT

disarmed during the entry delay time. The alarm sounder and keypad

sound continuously until the system is disarmed (or timeout occurs). An Exit

Alarm message is sent to the central station. OR

if an alarm from an exit or interior zone occurs within two minutes after the

end of an exit delay

Entering a second OFF sequence (Code + OFF ) will clear the display.

- 54 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Operation

System Displays

Display

Meaning

Remote Phone Control feature is active (Appears in place of the clock).

System Speaker Phone mode is active (Appears in place of the clock).

AC power is present. If not displayed, the system is operating on backup battery power.

ALARM

System is armed and an intrusion has been detected (also appears during a

fire alarm or audible emergency alarm). Accompanied by the protection zone

that is in alarm.

AWAY

All burglary zones, interior and perimeter, are armed.

BYPASS

CHIME

FAULT

One or more burglary protection zones have been bypassed.

Chime feature is activate

A malfunction is discovered in the system; or an open is detected in a fire zone; or a

fault in a day/night burglary zone is discovered during a disarmed period.

Accompanied by a display of the zone number in trouble.

FIRE

A fire alarm or fire fault is present. Accompanied by a display of the zone that

is in alarm

LOW BAT

Low battery condition in a wireless sensor (if zone number is displayed) or low system

battery (if no zone number is displayed). If 00 is displayed, a wireless keypad has a low

battery condition.

INSTANT

MESSAGE

REC

Entry delay is turned off.

A message has been recorded and has not yet been played back.

The system is in Recording mode.

STAY

TEST

Perimeter Burglary zones, such as protected windows and doors, are armed

System is in Test mode.

- 55 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Testing the System

Test Mode

After installation is completed, the security system should be carefully tested, as follows.

1. With the system in the disarmed state, check that all zones are intact. If the READY LED is not lit,

press the [ ✻] key to display the faulted zone(s). Restore faulted zone(s), if necessary, so that the

READY LED lights. Fault and restore every sensor individually to assure that it is being monitored by

the system.

2. Enter the security code and press the TEST key. The outside sounder will sound for 1 second and all

the LED segments on the keypad display light for 3 seconds. LYNXR-I announces the zone’s voice

descriptor (if programmed) followed by 3 beeps, each time a contact is faulted. A test report should be

transmitted (if programmed) to the central station immediately. If the backup battery is discharged or

missing, the sounder may not turn on and a LOW BATTERY report will be transmitted with a TEST

report. The keypad will beep once every 45 seconds as a reminder that the system is in the Test mode.

3. To turn off the Test mode enter security code and press the OFF key.

Notes: (1) Triggering a zone set to Arm AWAY, Arm STAY, or Disarm will take the system out of Test and cause that action.

(2) BR type transmitters do not display during Test mode (keypad beeps only)

(3) Macros cannot be run from the Test mode.

(4) Test mode automatically ends after 4 hours.

Armed System Test

Alarm messages will be sent to the central station during the following tests 1 and 2. Notify

them in advance that tests will be in progress.

1. Arm the system and fault one or more zones. After 15 seconds (if optional dialer delay is selected),

silence alarm sounder(s) by entering the code and pressing OFF. Check entry/exit delay zones.

2. Check the keypad-initiated alarms that are in the system by pressing the Panic key pairs. If the system

has been programmed for audible emergency, the keypad will emit a steady alarm sound, and

“ALARM” and zone number will be displayed. Silence the alarm by entering the security code and

pressing OFF.

If the system has been programmed for silent emergency, there will be no audible alarms or displays,

but a report will be sent to the central station.

3. If Powerline Carrier Devices have been installed, test their programmed action.

4. Notify the central station when all tests are finished, and verify results with them.

5. To test the wireless part of the system and the RF receiver, perform the two additional tests described

in the Installing Wireless Zones section: Sniffer mode and Go/No Go Test.

Note: System Test mode (installer/master code + test) and Go/No Go Test (installer code + # + 8) will be

automatically terminated after 3-1/2 to 4 hours if the installer or user does not manually terminate it. This

ensures that fire and panic zones will not remain disabled. However, Sniffer mode (installer code + # + 3) does

not automatically expire. You must manually exit (Installer/User Code + OFF) Sniffer mode to

return to normal operation.

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to

continuous satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and offering a regular maintenance program to the user

as well as acquainting the user with the proper operation and limitations of the alarm system and its component

parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to ensure the

system’s proper operation at all times.

- 56 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Communication

This section provides an explanation of formats this system accommodates for reporting alarms and other

system conditions to the central station. The process of a successful transmission consists of both the

method of communication between the control panel and the central station receiver, and the actual way the

information is sent and displayed at the central station.

Communication Overview

When the panel calls the central station receiver, it waits to hear a “handshake” frequency from the receiver

to confirm that the receiver is on-line and ready to receive its message. Once the panel hears the handshake

it is programmed to listen for, it sends its message. The panel then waits for a “kissoff” frequency from the

receiver acknowledging that the message was received and understood.

If the handshake frequency is not given or is not understood by the panel, the panel will not send its

message. Once the handshake frequency is received and understood by the panel, the panel will send its

message. If there is an error in the transmission (the receiver does not receive a “valid” message), the kissoff

frequency will not be given by the central station receiver.

The panel will make eight attempts to the primary telephone number and eight attempts to the secondary

telephone number (if programmed) to get a valid message through. If the panel is not successful after its

numerous attempts, the keypad will display “FC.” If the secondary number is a pager, “FC” displays after

the first 8 attempts to the primary number.

The following chart defines the three sets of (handshake/kissoff) frequencies that the panel supports, and the

different formats that can be sent for each.

FORMAT

Low Speed

3+1

HANDSHAKE

1400Hz

TRANSMITS DATA KISSOFF

TRANSMIT TIME

Under 15 seconds

1900Hz (10PPS)

1400Hz

(Standard report)

4+1

4+2

Sescoa/Rad

3+1

2300Hz

1900Hz (20PPS)

(Standard report)

2300Hz

Under 10 seconds

4+1

4+2

Express

4+2

Contact ID®

1400–2300Hz

DTMF (10 cps)

1400Hz

Under 3 seconds

Report Code Formats

3+1 and 4+1 Standard Formats Comprise a 3- (or 4-) digit subscriber number and a single digit report

code (e.g. alarm, trouble, restore, open, close, etc).

3+1 and 4+1 Expanded Formats Comprise a 3- (or 4-) digit subscriber number, and a 2-digit report code.

The first digit is displayed on the first line, followed by a second line

where the first digit is repeated 3 (or 4) times and followed by the

second digit. This is the “expanded” digit.

4+2 Format

Comprises a 4-digit subscriber number and 2-digit report code.

ADEMCO Contact ID®

Reporting Format

Comprises a 4-digit subscriber number, 1-digit event qualifier

(“new” or “restore”), 3-digit event code, and 3-digit zone number, user

number, or system status number (see the following page).

The following table shows the message formats for 3+1, 4+1 and 4+2 reports, where:

SSS or SSSS

Subscriber ID

Alarm Code (1st digit)

Typically Zone Number* (2nd digit)

Trouble Code (1st & 2nd digits)

Bypass Code (1st & 2nd digits)

C = Close Code (1st Digit)

User Number (in hex)

Test Code (1st & 2nd digits)

Alarm Restore Code

Trouble Restore Code (1st & 2nd digits)

AC Loss Code (1st & 2nd digits)

Low Battery Code (1st & 2nd digits)

Open Code (1st Digit)

Bypass Restore Code (1st & 2nd digits)

AC Restore Code (1st & 2nd digits)

Battery Restore Code (1st & 2nd digits)

*Zone numbers for: [ ] & [#] = 99; [1] + [ ] = 95; [3] + [#] = 96; Duress = 92

- 57 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

System Communication

Report

3+1/4+1 Standard

3+1/4+1 Expanded

4+2

Alarm

SSS(S) A

AAA(A) Z

SSS(S) T

TTT(T) t

SSS(S) B

BBB(B) b

SSS(S) E

SSSS AZ

Trouble

Bypass

AC Loss

SSS(S) T

SSS(S) B

SSS(S) E

SSSS Tt

SSSS Bb

SSSS EA

EEE(E) A

Low Battery

SSS(S) L

LLL(L) L

SSSS LL

Open

SSS(S) O

SSS(S) C

SSS(S) G

SSS(S) R

SSS(S) O

OOO(O) U

SSS(S) C

CCC® U

SSS(S) G

GGG(G)g

SSS(S) R

RRR® Z

SSSS OU

SSSS CU

SSSS Gg

SSSS RZ

Test

Restore Alarm

AC Restore

SSS(S) R

SSSSR

R R R (R )A

A A A

Low Battery Restore

Trouble Restore

Bypass Restore

SSS(S) R

SSSS R L

L B

R R R (R )L

L L L

SSS(S) R

SSSS R t

R R R (R )t

T T T

SSS(S) R

SSSS R b

R R R (R )b

B B B

ADEMCO Contact ID® Reporting takes the following format: CCCC Q EEE GG ZZZ where:

CCCC = Customer (subscriber) ID

Event qualifier, where: E = new event, and R = restore

Event code (3 hex digits) (for a complete list of event codes, refer to the central office receiver manual)

Always “00”

EEE

ZZZ

Zone/Contact ID® number reporting the alarm, or user number for open/close reports. System status

messages (AC Loss, Walk Test, etc.) contain zeroes in the ZZZ location.

CONTACT ID® EVENT CODES

Code

110

121

122

123

131

132

134

135

146

150

301

302

344

353

Definition

Code

381

383

384

401

Definition

RF Supervision Trouble

RF Sensor Tamper (Trouble)

RF Sensor Low Battery

Disarmed, Armed AWAY (NO DELAY),

Armed AWAY

Scheduled Auto Arm

Cancel by User

Remote Arm/Disarm (Downloading)

Quick Arm AWAY/NO DELAY

Disarmed/Armed STAY/NO DELAY, Quick Arm

STAY/NO DELAY

Bypass

Periodic Test

AAV to follow

System Test

Event Log 80% Full

System Inactivity

Fire Alarm

Duress

Alarm, 24-hour Silent

Alarm, 24-hour Audible

Alarm, Perimeter

403

406

407

408

441

Alarm, Interior

Alarm, Entry/Exit

Alarm, Day/Night

Silent Burglary

Alarm, 24-Hour Auxiliary

AC Power

Low System Battery/Battery Test Fail

RF Jam Detected

ECP Communication/Supervision failure, case

tamper or low battery

Fire Loop Trouble

570

602

606

607

623

654

373

374

380

Exit Error Alarm

Global Trouble, Trouble Day/Night

Notes: (1) The following codes are logged in the event log upon occurrence, but are not reported:

305 = System Reset

627 = Keypad Program Mode Entry

(2) LRR/IP Communications Module Low Battery and Low Battery restore reports are sent real time. LRR/IP Communications

Module trouble restore report is sent after two code + off (only if physically restored)

- 58 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Troubleshooting Guide

Trouble Conditions

The word “FAULT” on the keypad’s display, accompanied by a rapid “beeping” at the keypad, indicates that

there is a trouble condition in the system. Pressing any key can silence the audible warning sound. Instruct

users to call for service immediately upon seeing any of the following messages.

System Trouble Displays

Display

FAULT

Meaning

and one or more zone numbers indicates that a problem exists with the displayed

zone(s) and requires attention. After correcting the problem, the display can be cleared by

entering the security code plus the OFF key twice.

The fault condition may also be caused by some change in the environment that prevents

the built-in receiver from receiving signals from a particular wireless sensor.

Indicates one of the following:

FAULT 103

• control panel lost communication with the communications module

• communications module tamper detected (cover removed)

• primary communications path failure

• radio is not registered; account not activated

• primary power loss

• secondary communications path failure

• battery charger failure

• low battery

with no zone number indicates that the system’s backup battery is weak.

LOW BAT

with a zone number and a once-per-45 seconds “beeping” at the keypad indicates that a

low battery condition exists in the wireless sensor displayed (zone “00” indicates a wireless

button/keypad). If the battery is not replaced within 30 days, a “FAULT” display may occur.

Backup LRR/GSM/IP module communication failure (displayed on RF Keypad only)

appears if an exit or interior zone contained a fault during closing at the time the Exit

Delay ended (e.g., exit door left open), but the system was disarmed during the Entry Delay

time. The alarm sounder and keypad sound continuously, but stop when the system is

disarmed. No message will be transmitted to the central station.

Modem Comm.:

system is communicating with the central station for change of function or status

verification.

Busy-Standby

displayed upon power-up. After approximately 1 minute* the green “READY” LED should

light. If the “dI” remains displayed for more than 1 minute, the system is disabled.

*To bypass the 1-minute delay, press [#] + [0].

Important: Do not try to bypass 1minute delay before “dI” is displayed!

appears when Exit Delay ends if an exit or interior zone contained a fault during closing.

The alarm sounder and keypad sound continuously until the system is disarmed (or

timeout occurs). An “Exit Alarm” message is sent to the central station. Also results if an

alarm from an exit or interior zone occurs within 2 minutes after the end of an Exit Delay.

communication failure has occurred. This message clears only when the system is

subsequently armed.

system has detected an RF jamming condition or excessive interference.

Power Failure

No display

If there is no keypad display at all, and the LED indicators are not lit, operating power for

the system has stopped and the system is inoperative.

If the display is lit and the AC display is off, the system is operating on battery power only.

During an AC power loss, the backlighting will turn off and the indicators will flicker

slightly to minimize deep discharge of the battery.

- 59 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Troubleshooting Guide

S yst em (includ in g Wireless )

SYMPTOM

POSSIBLE CAUSE

1a. Transmitter not properly powered.

REMEDY

1a Check or change transmitter's battery.

1. Transmitter signal

not received at

control.

1b. Transmitter is located too far from RF 1b. Move transmitter or RF receiver.

receiver.

1c. Check for large metal obstructions, then relocate

1c. There is metal shielding between

transmitter and RF receiver.

transmitter if necessary.

1d. Verify by activating control with another,

similar transmitter. If O.K. now, return

defective transmitter.

1d. Transmitter is malfunctioning.

1e. Transmitter No. (zone) is not

programmed.

1e. Verify programming.

2a. Transmitter zone type (ZT) is set to 00

(Not Used).

2a. Set ZT to a valid active zone type in field ✻56.

2. Transmitter zone

number appears

during Transmitter

Sniffer mode, but

does not clear.

2b. Transmitter battery not installed.

2b. Install proper battery.

2c. 5800 System transmitter not "entered" in 2c. "Enter" unit in field ✻56 or ✻83.

system.

3. Low battery message

on keypad.

3a. "Low Bat" (no zone Nos.)

3b. "Low Bat" + "00".

3a. System battery is low or missing.

3a. Replace system battery.

3b. Remote RF keypad/button battery is low. 3b. Replace battery in the RF keypad.

3c. "Low Bat" + "nn".

3c. Transmitter for zone “nn” has a low

battery.

3c. Replace the battery in the displayed

transmitter.

3d. Standard- or High-Capacity battery

connected to wrong receptacle.

3d. Ensure that battery is properly connected.

4a. System is in Test mode.

4a. Enter Code + OFF to exit Test mode.

4. Periodic beep(s) from

keypad.

4b. A transmitter low battery has occurred

and is displayed.

4b. Enter Code + OFF and replace the battery.

4c. A supervision fault has occurred.

4c. Check the transmitter indicated. Restore

communication to the receiver to cancel the

condition.

4d. Replace system battery

4d. System low battery

Put control in Test mode. If zone does not

respond, try operating the tamper switch or

another input to the transmitter.

5. There is no response

to a transmitter in

normal operation,

although zone

5a. If another input causes the zone to be

displayed, the wrong input was "entered"

when programming.

5a. Delete input's serial number (not the zone), and

number clears during

Transmitter Sniffer

mode.

enter the proper input (see field ✻56).

5b. If no response at all from this

transmitter, this physical transmitter

has not been entered by the system.

Transmitter Sniffer display is being

cleared by another unit programmed for

this zone.

5b. Determine which transmitter is programmed for

this zone and reprogram as necessary.

6a. Sensors not properly installed, wired, or

monitored.

6a. Check installation to see if in accordance with

established procedure.

6. Nuisance or phantom

alarm.

6b. Universal transmitter (5817)

programmed wrong.

6b. Check programming switches on transmitter.

7a. Check with all occupants of protected home.

7b. Check setting of entry and exit delays.

7a. Protected door or window opened while

system armed.

7. Intrusion alarm for

no apparent reason.

7b. Improper user operation of exit/entry

delays.

7c. Magnets located too far from switches,

and/or doors and windows not properly

aligned.

7c. Check all openings for proper switch and

magnet orientation.

- 60 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-i Installation and Setup Guide

Troubleshooting Guide

Co nt ro l

SYMPTOM

POSSIBLE CAUSE

REMEDY

1a. Interrupted AC power supply.

1a. Check transformer connection and

powerline circuit breaker.

1. The word “AC” is not

displayed.

2a. System in Test mode.

2b. Telephone connection not secure.

2c. Digital communicator

malfunctioning.

2a. Remove from Test mode.

2b. Check all connections.

2c. Check with a different CONTROL

PANEL.

2. Digital communicator

message not being

received.

2d. Program prefix or access code into the

CONTROL PANEL.

2e. System cannot work in this situation.

2d. Telephone number in program needs

prefix or access code.

2e. Telephone call to central monitoring

station requires operator assistance.

3. Does not arm properly.

READY light not on.

Open or faulted zone(s)

Check for faulted zones and make intact,

or use Bypass arming, if desired.

4. System doesn't respond to

keystrokes on keypad.

4a. System is in communication with

downloader at central station.

4a. Wait until download session is

finished.

4a. "CC" displayed.

4b. System has just been powered and is

in its one minute initialization.

4b. "d1" displayed.

4b. Wait for initialization to finish, or

bypass this time by pressing '#' + '0.'

Smoke Detectors

SYMPTOM

POSSIBLE CAUSE

REMEDY

1. Detector alarms, no

apparent reason.

1a. Dust, dirt in sensing chamber.

1a. Clean unit's sensing

chamber with vacuum

cleaner per unit's

1b. Improper location.

instructions.

1b. See unit's instructions

for locations to avoid.

1c. Unit malfunctioning.

Relocate as necessary.

1c. Replace detector.

2. Detector's siren sounds.

2a. Unit not receiving required power.

2b. Unit malfunctioning.

2a. Check for proper

installation of battery.

Try new battery.

2b. Replace detector.

- 61 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Programming Default Tables

(boldface indicates defaults that differ between tables)

Function

Table 1

Table 2

Table 3

Table 4

*20 Installer code

4112

*21 Quick arm enable

*22 Keypad backlight timeout

*23 Forced bypass

*24 RF house ID code

0,0

*25 Powerline carrier device house code

*26 Chime-by-zone

*27 Real-time clock display

*29 Daylight saving time start/end month

*30 Daylight saving time start/end weekend

*31 Single alarm sounding per zone

*32 Fire sounder timeout

4,10

1,5

4,10

1,5

4,10

1,5

4,10

1,5

*33 Alarm bell timeout

*34 Exit delay

7,0

6,0

7,0

*35 Entry delay 1 (zone type 01)

*36 Entry delay 2 (zone type 02)

*37 Audible exit warning/quick exit

*38 Confirmation of arming ding

*39 Power up in previous state

*40 PABX access code

3,0

6,0

1,1

---

4,5

6,0

0,1

---

3,0

6,0

1,1

---

3,0

6,0

1,1

---

*41 Primary phone number

*42 Secondary phone number

*43 Primary subscriber account number

*44 Secondary subscriber account number

*46 “Follow Me Reminder” Phone Number

*47 Phone system select

---

15,15,15,15

---

*48 Report format

7,7

*49 Split/dual reporting

*50 15 second dialer delay (burglary)

*51 Periodic test report

*52 First test report offset

*53 Sescoa/radionics select

*54 Lack of usage notification

*55 Enable/Disable ECP interface

*56 Enhanced Zone programming

*58 RF jam detection

See *56 table

*59 Exit error report code

*60 Trouble report code

1,0

*61 Bypass report code

0,0

*62 AC loss report code

0,0

*63 Low battery Report code

*64 Test report code

1,0

*65 Open report code

*66 Arm away/stay report code

*67 RF transmitter low battery report code

*68 Cancel report code

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

*70 Alarm restore codes

*71 Trouble restore report code

*72 Bypass restore report code

*73 AC restore report code

*74 Low battery restore report code

*75 RF transmitter low battery restore report code

*76 Test restore report code

*77 Dynamic Signaling Delay/ Dynamic Signaling Priority

*80 Powerline Carrier Devices

*81 Zone lists for devices

*84 Assign zone voice descriptors

*87 Auxiliary Function/ 1-button paging

*88 Pager characters

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

---

1,0

0,0

1,0

0,0

1,0

0,0

See *80 table

See *81 table

See *80 table

See *81 table

Refer to *84 Programming

See *80 table

See *81 table

---

*89 Event log 80% full report code

0,0

- 62 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Programming Default Tables

(boldface indicates defaults that differ between tables)

Function

Table 1

Table 2

Table 3

Table 4

*90 Event logging

*91 Alarm audio verification/remote phone control

*92 Number of reports in armed period

*93 Flexible call back

*94 Download phone number

---

*95 Ring detect count for downloading/remote phone control

Default Master Code

Default Duress Code

1,2,3,4

---

1,2,3,4

---

1,2,3,4

---

1,2,3,4

---

By activating *96, Field 43, and 44 will be changed to 15, 15, 15, 15.

✻56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLE 1

Zone No. Zone Type Alarm Code

Input Type

3 (RF)

5 (BR)

---

Loop Number

Zone Descriptor

1,0

0,0

1,0

0,0

1,0

---

47, 04 (FRONT DOOR)

33, 04 (BACK DOOR)

80 (WINDOW)

---

56 (MOTION DETECTOR)

---

NOTE: Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic

✻56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLE 2

Zone No. Zone Type Alarm Code

Input Type

3 (RF)

5 (BR)

---

Loop Number

Zone Descriptor

47, 04 (FRONT DOOR)

33, 04 (BACK DOOR)

48, 04 (GARAGE DOOR))

56 (MOTION DETECTOR)

22, 02 (SMOKE DETECTOR)

1,0

0,0

1,0

0,0

1,0

---

NOTE: Zone 2 to 41 are RF zones; Zone 92 is Duress; Zones 95, 96 and 99 are keypad panics

- 63 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Programming Default Tables

✻56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLES 3 & 4

Zone No. Zone Type Alarm Code

Input Type

3 (RF)

5 (BR)

---

Loop Number

Zone Descriptor

47, 04 (FRONT DOOR)

33, 04 (BACK DOOR)

80 (WINDOW)

56 (MOTION DETECTOR)

22, 02 (SMOKE DETECTOR)

1,0

0,0

1,0

0,0

1,0

---

NOTE: Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic

✻80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 4 (devices 2-7 have no default values)

Start

Stop

Zone Type

System Operation

Restore of

Zone List

Zone type

System operation

Device Number

Action

Event

Zone List

8**

** NOTE: If using an X10 Powerhouse Security SH10A siren as device 8, you must change the device action default to “3” if using default

table 4.

✻80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 1 and 2 (devices 1-7 have no default values)

Start

Stop

Zone Type

System Operation

Restore of

Zone List

Zone type

System operation

Device Number

8**

Action

Event

Zone List

✻81 ZONE LIST FOR OUTPUT DEVICES DEFAULT TABLE: Applies To Default Table 1 - 4.

Zone List 1 28, 32

Zone List 2 29, 33

Zone List 3 2, 3

- 64 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

– Index –

*56 Enhanced Zone Programming Mode............... 13, 24, 28, 29

Busy-Standby .......................................................................... 59

Button Transmitters ......................................................... 13, 14

Button Type............................................................................. 30

Button Zones............................................................................ 30

Bypass...................................................................................... 55

Bypass Report Code........................................................... 24, 62

Bypass Restore Report Code ............................................. 25, 62

80 Device Programming....................................... 28, 34, 35, 36

*81 Zone List Menu Mode.................................................. 28, 37

*83 Enhanced Sequential Mode .................28, 29, 32, 38, 39, 40

*84 Assign Zone Voice Descriptors........................ 28, 33, 41, 42

*85 Record Custom Voice Descriptors............................... 28, 43

96 Initialize Download ID and Subscriber Acct. No. for

Downloading........................................................................28

97 Set All Program Fields to 1 of 4 Sets of Default Values...28

98 Exits Programming Mode .................................................28

99 Exits Programming Mode .................................................28

-C-

Callback Number..................................................................... 27

Cancel Report Code ................................................................. 62

Canceled Alarm ....................................................................... 24

Change the Master Code......................................................... 50

Chime by Zone......................................................................... 20

Chime Mode....................................................................... 20, 51

Chime-by-Zone......................................................................... 62

Closing Report......................................................................... 21

Communication ......................................................................... 4

Communication Overview....................................................... 57

Compass Downloader.............................................................. 48

Confirmation of Arming Ding ................................................. 62

Confirmation of Arming Ding ................................................. 21

Connecting AC Power and Backup Battery............................ 11

Contact ID ............................................................................... 57

Contact ID Event Codes.......................................................... 58

Contact ID Format ............................................................ 24, 50

Contact ID Reporting ........................................................ 58, 70

Contacting Technical Support................................................. 70

Custom Descriptor Number .................................................... 43

Custom Voice Descriptors ................................................. 28, 43

1.2-Volt Nickel-Metal Hydride Batteries.................................12

15 Second Dialer Delay...................................................... 23, 62

24-Hour Audible Alarm ...........................................................19

24-Hour Auxiliary Alarm.........................................................19

24-Hour Silent Alarm ........................................................ 18, 50

5800 Series Transmitters ........................................................13

5800RL............................................................................... 13, 15

5801..........................................................................................13

5802MN.............................................................................. 13, 14

5802MN2..................................................................................14

5804.............................................................................. 13, 14, 38

5804BD......................................................................... 13, 14, 20

5804BDV...................................................................... 13, 14, 20

5804E ................................................................................. 13, 14

5816.................................................................................... 13, 38

5817..........................................................................................13

5827.............................................................................. 13, 15, 20

-A-

AC Loss Report Code ......................................................... 24, 62

AC Power ........................................................................... 11, 12

AC Restore Report Code ..........................................................62

ADEMCO Express ............................................................. 22, 70

ADEMCO Low Speed......................................................... 22, 70

Alarm Bell Timeout ........................................................... 20, 62

Alarm Output.............................................................................4

Alarm Restore Codes ...............................................................62

Alarm Restore Report Code.....................................................25

Alarm Sounder.........................................................................70

Alarmnet Radio and Internet Communication Devices............8

Arm Away/Stay Report Code............................................. 25, 62

Arm–Away ...............................................................................19

Armed System Test..................................................................56

Arm–Stay.................................................................................19

Assign (or Change) a Secondary Security Code ......................50

Assign Custom Voice Descriptors............................................43

Assign Zone Voice Descriptors........................................... 41, 62

Audible Exit Warning/Quick Exit ..................................... 21, 62

Audio Alarm Verification (AAV)/Remote Phone Control ........27

Audio Alarm Verification (Two-Way Voice Feature)...............53

AUX Function ..........................................................................52

AUX Function/1-Button Paging......................................... 27, 62

AUX Key ..................................................................................27

Away Mode...............................................................................51

-D-

Data Encryption...................................................................... 48

Data Field................................................................................ 16

Daylight Savings Time Start/End..................................... 20, 62

Default Master Code ............................................................... 63

Default Tables ................................................................... 62, 63

Delete a Secondary Security Code .......................................... 50

Delete Entire Zone List........................................................... 37

Delete Zone Parameters Confirmation ............................. 31, 40

Delete Zones ............................................................................ 37

Descriptor .......................................................................... 33, 41

Desktop Mounting..................................................................... 5

Device Action........................................................................... 36

Device Number........................................................................ 36

DIP Switches ........................................................................... 13

Disable Local Sounder............................................................... 7

Disarm............................................................................... 19, 51

Download Call Back Phone Number....................................... 28

Download Phone Number........................................................ 63

Download, Initial..................................................................... 48

Downloader...................................................................27, 48, 49

Duress Code....................................................................... 50, 63

Dynamic Signaling .................................................................. 26

-E-

Enable/Disable LRR/IP Communications Device ................... 23

Encrypted (High-Security) Devices..............................14, 15, 31

Enroll Mode ....................................................................... 32, 39

Enter/Change the Master Code............................................... 50

Entry Delay ..................................................................21, 59, 62

Entry/Exit Burglary ................................................................ 18

Error Code 374 ........................................................................ 24

Event Log 80% Full Report Code...................................... 27, 62

Event Logging.................................................................... 27, 63

Exit Alarm............................................................................... 24

-B-

Babysitter Code........................................................................50

Back Plate..................................................................................5

Backlighting.............................................................................20

Backup Battery........................................................................11

Backup Reporting ....................................................................21

Battery Life..............................................................................14

Bell...........................................................................................70

BR....................................................................................... 13, 30

Burglary Zones.........................................................................20

- 65 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Exit Delay.................................................................... 21, 59, 62

Exit Delay Restart............................................................. 21, 51

Exit Door.................................................................................. 21

Exit Error Alarm ..................................................................... 59

Exit Error Report Code...................................................... 24, 62

Exit Warning ........................................................................... 21

Exiting Program Mode ............................................................ 17

Expert Programming............................................................... 16

Express .................................................................................... 57

External Sounder..................................................................... 20

Message Center........................................................................51

Modem Comm...........................................................................59

Mounting Base ...........................................................................5

Mute System Announcements .................................................51

-N-

No Alarm Response..................................................................19

No Delay...................................................................................51

Number of Reports in Armed Period .................................27, 63

-O-

-F-

Open Report Code ..............................................................25, 62

Operator Commands................................................................53

Optima 24 Plus FAX96 Modem................................................48

Other Features...........................................................................4

Other Functions .......................................................................51

Factory Defaults ...................................................................... 17

Fault................................................................................... 55, 59

FC............................................................................................. 57

FCC Statement........................................................................ 68

Features..................................................................................... 4

Fire Sounder Timeout........................................................ 20, 62

First Test Report Offset..................................................... 23, 62

Flexible Callback ......................................................... 27, 48, 63

Follow Me Alarm Announcement............................................ 54

Follow Me Reminder Feature.................................................. 54

Follow Me Reminder” Phone Number..................................... 22

Forced Bypass.............................................................. 20, 52, 62

-P-

PABX Access Code .............................................................21, 62

Pager.........................................................................................23

Pager Characters................................................................27, 62

Pager Function.........................................................................52

Pager Message..........................................................................27

Pager Report Format ...............................................................23

Paging Feature.........................................................................27

Panic Keys................................................................................50

Perimeter Burglary..................................................................18

Periodic Test Report...........................................................23, 62

Phone System Select ..........................................................22, 62

Piezo .........................................................................................70

Play Back a Message................................................................51

Plug-In Transformer ................................................................11

Power Up in Previous State...............................................21, 62

Powerline Carrier Device................................. 20, 34, 35, 54, 62

Powerline Carrier Device House Code.....................................62

Powerline Carrier Device Programming..................................36

Primary Phone Number.....................................................21, 62

Primary Subscriber Account Number................................22, 62

Program Mode, Entering..........................................................16

Programming Default Tables.......................................62, 63, 64

Programming Mode..................................................................20

-G-

General Information................................................................ 13

General Programming Information......................................... 16

Go/No Go Test Mode................................................................ 14

-H-

Handshake Frequency............................................................. 57

Hayes ....................................................................................... 48

House ID...................................................................... 15, 20, 35

House Identification ................................................................ 13

-I-

Input Type ................................................................... 13, 30, 63

Installer Code .............................................................. 20, 50, 62

Interactive Mode...................................................................... 17

Interior W/Delay...................................................................... 19

Interior, Follower..................................................................... 18

-Q-

Quick Arm ................................................................................51

Quick Arm Enable..............................................................20, 62

Quick Exit.................................................................................21

-K-

Keypad Backlight Timeout................................................ 20, 62

Keypad Functions.............................................................. 51, 52

Keys ......................................................................................... 13

Kissoff Frequency.................................................................... 57

-R-

Radio and Internet Communication Modules............................8

Radionics ..................................................................................22

Radionics/SESCOA ..................................................................70

Range........................................................................................13

Real Time Clock Display....................................................20, 65

REC ..........................................................................................55

Rechargeable Backup Battery .................................................12

Record a Message.....................................................................51

Redundant Reporting/Dynamic Signaling Delay ..............26, 62

Remote Phone Access...............................................................28

Remote Phone Control .............................................................52

Remote Phone Control Feature................................................52

Remote Programming ..............................................................48

Remote Programming/Control...........................................48, 49

Replacing the Rechargeable Battery .......................................12

Report Code........................................................................24, 30

Report Code Formats ...............................................................57

Report Format....................................................................22, 62

Restart Exit Delay..............................................................21, 51

-L-

Lack of Usage Notification ...................................................... 23

Long Range Radio.................................................................... 26

Loop and Serial Number ......................................................... 31

Loop Number ..................................................................... 31, 63

Low Battery Report Code .................................................. 25, 62

Low Battery Restore Report Code..................................... 25, 62

Low Speed................................................................................ 57

LYNX-DM.................................................................................. 5

LYNXRCHKIT-HC.................................................................. 12

LYNXRCHKIT-SC................................................................... 12

LYNXRCHKIT-SHA................................................................ 12

-M-

Macro Function........................................................................ 27

Master Code............................................................................. 50

Master Security Code .............................................................. 20

Memory of Alarm..................................................................... 51

Message.................................................................................... 55

- 66 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

RF.............................................................................................30

RF (Supervised Rf)...................................................................13

RF House ID Code ............................................................. 20, 62

RF Transmitter Low Battery Report Code........................ 25, 62

RF Transmitter Low Battery Restore .....................................62

RF Transmitter Low Battery Restore Code ............................25

RF Jam.....................................................................................24

Ring Detect Count for Downloading.................................. 28, 63

-T-

Technical Support.................................................................... 70

Telco Handoff........................................................................... 48

Temporal Pulse........................................................................ 20

Test Mode ...............................................................51, 56, 60, 61

Test Report Code ............................................................... 25, 62

Test Restore Report Code........................................................ 62

Testing the System.................................................................. 56

Time and Date......................................................................... 51

Transmitter Loop Numbers .................................................... 15

Transmitter Supervision......................................................... 13

Transmitters............................................................................ 13

Trouble by Day/ ....................................................................... 18

Trouble Conditions.................................................................. 59

Trouble Report Code.......................................................... 24, 62

Trouble Restore Report Code ............................................ 25, 62

Troubleshooting Guide............................................................ 59

-S-

Scheduling.......................................................................... 49, 51

Secondary Phone Number ................................................. 21, 62

Secondary Subscriber Account Number............................ 22, 62

Secondary User Codes .............................................................50

Security Code Handshake .......................................................48

Security Codes ................................................................... 20, 50

Security Functions...................................................................51

Serial Number.............................................28, 29, 31, 32, 38, 40

Sescoa/Rad ...............................................................................57

Sescoa/Radionics Select ............................................... 23, 24, 62

Setting Dip Switches................................................................15

SH10A......................................................................................36

Signal Strength........................................................................14

Silent Burglary ........................................................................19

Single Alarm Sounding Per Zone ...................................... 20, 62

Siren/Horn................................................................................36

Site-Initiated Remote Programming.......................................48

Smartmodem 1200...................................................................48

Smoke Detectors ......................................................................61

Sniffer Mode................................................................. 14, 56, 60

Special Features ........................................................................4

Specifications ...........................................................................70

Split/Dual Reporting.......................................................... 23, 62

Start by Event..........................................................................34

Start by Zone Type...................................................................34

Start Event Type......................................................................36

Start Zone List.........................................................................36

Start Zone Type .......................................................................36

Station-Initiated Remote Programming..................................48

Stay Mode ................................................................................51

Stop Recording.........................................................................51

Stop Zone List..........................................................................36

Stop Zone Type.........................................................................36

Supervised Fire........................................................................19

Supervised RF.................................................................... 13, 30

System Battery ........................................................................60

System Communication..................................................... 57, 58

System Features ........................................................................4

System Operation .................................................. 34, 35, 50, 64

System Power.............................................................................4

System Words ..........................................................................42

-U-

Unsupervised Button RF......................................................... 13

Unsupervised RF..................................................................... 13

UR (Unsupervised RF) ...................................................... 13, 30

User Codes........................................................................... 4, 51

-V-

Voice Descriptor............................................................30, 32, 41

Voice Prompt Programming Mode .......................................... 16

Voice Vocabulary Index........................................................... 42

Voltage Input........................................................................... 70

Volume Control........................................................................ 51

-W-

Wall Mounting........................................................................... 5

WAVE2EX ............................................................................... 70

Wireless Buttons ..................................................................... 13

Wireless Transmitter .............................................................. 25

Wiring Connections................................................................... 6

World Wide Web Address........................................................ 70

-X-

X10................................................................................34, 49, 54

-Z-

Zone Bypass............................................................................. 51

Zone Descriptor ....................................................................... 63

Zone Entry To List .................................................................. 37

Zone List.......................................................................28, 62, 64

Zone List Number.................................................................... 37

Zone List Programming........................................................... 37

Zone Number................................................................30, 38, 41

Zone Programming.................................................................. 62

Zone Response Type .......................................................... 18, 19

Zone Type .......................................................................... 30, 36

Zones and Devices ..................................................................... 4

- 67 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Regulatory Agency Statements

UL NOTICE: This is a "Grade A" residential system

FCC STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)

THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Federal Communications Commission (FCC) Part 15 Statement

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following

statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with

the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to

comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are

designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•

If using an indoor antenna, have a quality outdoor antenna installed.

Reorient the receiving antenna until interference is reduced or eliminated.

Move the radio or television receiver away from the receiver/control.

Move the antenna leads away from any wire runs to the receiver/control.

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or

installer may find the following booklet prepared by the Federal Communications Commission helpful: "Interference Handbook." This

booklet is available from the U.S. Government Printing Office, Washington, DC 20402.

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's

Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

Federal Communications Commission (FCC) Part 68

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC

registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when

requested.

This equipment uses the following USOC jack: RJ31X

This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs.

This equipment is hearing-aid compatible.

Industry Canada

NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment

Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer

should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made

by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to

disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal

metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection

authority, or electrician, as appropriate.

Ringer Equivalence Number Notice:

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of

terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of

devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

- 68 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

WARNING

THE LIMITATIONS OF THIS ALARM SYSTEM

While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or

other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a

variety of reasons. For example:

•

Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or

disconnect an alarm warning device.

•

Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work

without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put

in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.

•

Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the

signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.

•

A user may not be able to reach a panic or emergency button quickly enough.

While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not

activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the

Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may

not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not

sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of

closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector,

for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke

detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by

carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable

materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire

and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to

allow all occupants to escape in time to prevent injury or death.

•

Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their

installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams

of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion

or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.

Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical

system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the

ambient temperature of the protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection

performance can decrease.

Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the

other side of closed or partly open doors. If warning devices are located on a different level of the residence from the

bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not

hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing

traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people.

•

Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or

temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect

themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond

appropriately.

•

This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to

last as long as 10 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This

alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad

(and remote keypad) should be tested as well.

Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions.

Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device

being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce

the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus

allowing time to arrange a change of battery to maintain protection for that given point within the system.

Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for

insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to

insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones

to learn about these developments.

- 69 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-I Installation and Setup Guide

Specifications

LYNXR-I

Security

Controls

1. Physical: 10-3/8” W x 7-1/8” H x 1-3/4” D

2. Electrical:

VOLTAGE INPUT: 9VAC from plug-in 25VA transformer.

RECHARGEABLE BACKUP BATTERY: Nickel-metal hydride battery pack

rated at 7.7Vdc.

ALARM SOUNDER: Piezo = 6-14VDC, 30mA max/ Bell = 6-14VDC, 120mA max

(e.g., ADEMCO’s WAVE2EX).

3. Communication:

FORMATS SUPPORTED:

ADEMCO Express, 10 characters/sec, DTMF (TouchTone) Data Tones,

1400/2300Hz ACK, 1400Hz KISSOFF.

ADEMCO Contact ID® Reporting, 10 characters/sec., DTMF (TouchTone)

Data Tones, 1400/2300Hz ACK, 1400Hz KISSOFF.

ADEMCO Low Speed, 10 pulses/sec, 1900Hz Data Tone,

1400Hz ACK/KISSOFF.

Radionics/SESCOA, 20 pulses/sec, 1800Hz Data Tone, 2300Hz

ACK/KISSOFF. Can report 0–9, B–F.

Line Seize: Double Pole

Ringer Equivalence: 0.6B

FCC Registration No.: 5GBUSA-25623-AL-E

Contacting Technical Support

PLEASE, before you call Technical Support, be sure you:

•

READ THE INSTRUCTIONS!

Check all wiring connections.

Determine that the power supply and/or backup battery are supplying proper

voltages.

•

Verify your programming information where applicable.

Note the proper model number of this product, and the version level (if known) along

with any documentation that came with the product.

Note your ADEMCO customer number and/or company name.

•

Having this information handy will make it easier for us to serve you quickly and

effectively.

You may contact Technical Support via Toll Free Fax. Please include your return fax number. You

will receive a reply within 24 hours.

Technical Support: ....................................................................1-800-645-7492 (8 a.m.-8 p.m. E.S.T.)

FAX FAXBACK Automated Fax Retrieval System:.........................1-800-573-0153 or 1-516-921-6704 / ext. 1667

World Wide Web Address: .........................................................http://www.honeywell.com/security

- 70 -

Download from Www.Somanuals.com. All Manuals Search And Download.

C K B L A

Y E L L O

C A R R I E R D E V I C E S

W E P R O L I N E

O A U T A T D

G N D

N I A T D A

Notes: Connection of the fire alarm signal to a fire alarm headquarters or a central station shall be permitted with the

approval of the local authority having jurisdiction. The burglar alarm signal shall not be connected to a police

emergency number.

The System must be checked by a qualified technician once every three years.

- 71 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

Honeywell International Inc. acting through its Security & Custom Electronics business ("Seller"), 165

Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans and

specifications and to be free from defects in materials and workmanship under normal use and service for 24

months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12

months from date of original purchase unless the installation instructions or catalog sets forth a shorter

period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or

replacing, at its option, free of charge for materials or labor, any product, which is proved not in compliance

with Seller's specifications or proves defective in materials or workmanship under normal use and service.

Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or

improperly repaired or serviced by anyone other than Honeywell factory service. Connection of any device(s)

to a communicating bus of a Honeywell security system (e.g., keypad bus, polling loop) other than those

manufactured or approved by Honeywell shall void this warranty. For warranty service, return product

transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR

A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE

FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL

OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR

IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR

DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

Seller does not represent that the products it sells may not be compromised or circumvented; that the

products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the

products will in all cases provide adequate warning or protection. Customer understands that a properly

installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events

occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that

there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO

LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A

CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE,

WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS

LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM

LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH

SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces

any previous warranties and is the only warranty made by Seller on this product. No increase or alteration,

written or verbal, of the obligations of this Limited Warranty is authorized.

165 Eileen Way, Syosset, New York 11791

www.honeywell.com/security

‡K14114ÉŠ

K14114 3/06 Rev. B

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Car Seat PD205009A User Manual
Graco Inc Pressure Washer 226314 User Manual
Graco Oven 309572ZAG User Manual
Graco Stroller 6451 User Manual
Halo Lighting System Indoor Furnishings H1312 User Manual
HANNspree Flat Panel Television DT06 10U1 User Manual
Harbor Freight Tools Greenhouse Kit 92050 User Manual
HP Hewlett Packard Calculator 20B User Manual
HP Hewlett Packard Server RX7620 16 User Manual
Hubbell Water Heater ST User Manual