Owner's Manual
Installation and Operation
Model:
TL2.0
Non-Catalytic, Top Load,
Wood Burning Room Heater
Item #1-90-856000
NOTICE
dO NOT dIsCaRd THIs MaNuaL
• Leave this manual with
• Important operating and
maintenance instructions
included.
• Read, understand and
follow these instructions
for safe installation and
operation.
party responsible for use
and operation.
WaRNINg
WaRNINg
PLEasE REad THIs ENTIRE MaNuaL
BEfORE INsTaLLaTION aNd usE Of
THIs WOOd-BuRNINg ROOM HEaTER.
faILuRE TO fOLLOW THEsE
INsTRuCTIONs COuLd REsuLT IN
PROPERTy daMagE, BOdILy INjuRy
OR EvEN dEaTH.
HOT suRfaCEs!
gLass aNd OTHER suRfaCEs
aRE HOT duRINg OPERaTION
aNd COOL dOWN.
HOT, WILL CausE BuRNs.
•
•
•
•
dO NOT TOuCH gLass uNTIL IT Is COOLEd
NEvER aLLOW CHILdREN TO TOuCH gLass
kEEP CHILdREN aWay
CaREfuLLy suPERvIsE CHILdREN IN saME
ROOM as fIREPLaCE.
aLERT CHILdREN aNd aduLTs TO HazaRds Of
HIgH TEMPERaTuREs.
HIgH TEMPERaTuREs May IgNITE CLOTHINg OR
OTHER fLaMMaBLE MaTERIaLs.
• dO NOT sTORE OR usE gasOLINE OR OTHER
fLaMMaBLE vaPORs aNd LIquIds IN THE
vICINITy Of THIs OR aNy OTHER aPPLIaNCE.
• dO NOT OvERfIRE - If aNy ExTERNaL PaRT
sTaRTs TO gLOW, yOu aRE OvERfIRINg.
CLOsE aIR CONTROLs. OvERfIRINg WILL
vOId yOuR WaRRaNTy.
•
•
kEEP CLOTHINg, fuRNITuRE, dRaPERIEs aNd
OTHER fLaMMaBLE MaTERIaLs aWay.
• COMPLy WITH aLL MINIMuM CLEaRaNCEs TO
COMBusTIBLEs as sPECIfIEd. faILuRE TO
COMPLy May CausE a HOusE fIRE.
CauTION
CauTION
CHECk BuILdINg COdEs PRIOR TO INsTaLLaTION.
TEsTEd aNd aPPROvEd fOR usE WITH dRy,
sEasONEd CORdWOOd ONLy. dO NOT BuRN
WET OR gREEN WOOd. BuRNINg aNy OTHER
TyPE Of fuEL WILL vOId yOuR WaRRaNTy.
•
•
INsTaLLaTION MusT COMPLy WITH LOCaL, REgIONaL,
sTaTE aNd NaTIONaL COdEs aNd REguLaTIONs.
CONsuLT LOCaL BuILdINg, fIRE OffICIaLs OR
auTHORITIEsHavINgjuRIsdICTIONaBOuTREsTRICTIONs,
INsTaLLaTION INsPECTION, aNd PERMITs.
3-90-08560
Rev: #3 September, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
TaBLE Of CONTENTs
section 1: Listing and Code approvals
section 9: service & Maintenance
A. Soot Formation (Removal)
B. General Maintenance Procedures
A. Appliance Certifications
B. Mobile Home Approval
C. Glass Specifications
4
27
28
4
4
4
4
D. Electrical Rating
section 10: Reference Materials
A. Wiring Diagram (Blower Option)
B. Service Parts Listing
E. BTU & Efficiency Specifications
30
31
34
35
section 2: special Warnings and Notes
A. Carbon Monoxide Warnings &
C. EPA Hang Tag
D. Warranty Policy
Considerations
5
section 3: getting started
A. Design, Installation & Location
B. Fire Safety
C. Component Locator
D. Pre-Use Checklist
This room heater must be connected to:
6
6
7
8
1) a chimney complying with the requirements for
Type HT chimneys in the standard for Chimneys,
factory-Built, Residential Type and Building
Heating appliance, uL 103
or
section 4: dimensions & Clearances
A. Appliance Dimensions
B. Clearances to Combustibles
C. Floor Protection
2) a Code approved Masonry Chimney with a flue
Liner.
9
10
12
section 5: Chimneys and venting
A. Draft
B. Chimney Connectors
C. Wall Pass-Throughs
D. The Chimney
13
13
13
14
section 6: Mobile Home - (us only)
A. Mobile Home Installation
20
section 7: appliance set-up
A. Outside Air Attachment
B. Leveling The Appliance
C. Optional Cooking Grill
D. Optional Blower Kit
21
21
21
22
22
22
E. Top Air Grill Option
F. Brushed Stainless Trim option
section 8: Operating Instructions
A. Fuel Specifications
B. General Operating Information
C. Burning as a Fireplace
D. Combustion Process
E. User Controls
F. Before Your First Fire
G. Building & Maintaining a Fire
23
23
24
24
25
25
25
3
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Listing and Code approvals
1
a. appliance Certification
E. BTu & Efficiency specifications
Model:
TL2.0 Woodburning Stove
Particulate Emissions
Rating:
2.6g/hr Avg
Laboratory: OMNI-Test Laboratories, Inc.
Report No.
Type:
135-S-29-2
Solid Fuel Room Heater / Wood
Burning Type.
*BTU Input:
Heating Capacity:
Firebox Size:
Fuel:
9,600 - 31,800 / hr
1,600-1,900 sq. ft.††
2.0 cu. ft.
Standard(s): UL1482-11, UL737-11 &
ULC S627-00
Dry Cordwood
Shipping Weight:
475 lbs.
This appliance is also approved for installation in
*BTU input based on EPA test fuel. Actual cordwood
values will vary.
a shop.
††Heating capacity based on zones 1 and 2, covering
the Northern United States.
B. Mobile Home approved
This appliance is approved for Installation in mobile/
manufactured homes in the us only. The structural
integrity of the mobile home floor, ceiling and walls
must be maintained. The appliance must be properly
grounded to the frame of the mobile home, and must
never be installed in a room designated for sleeping.
The unit must have provisions for an outside air source
when installed in a mobile home.
C. glass specifications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please
contact your dealer for replacement glass if needed.
d. Electrical Rating
Optional Blower: 115 VAC, 60 Hz. <1 Amps
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
special Warnings and Notes
2
Carbon monoxide, referred to as CO, is a colorless,
odorless gas that is produced during combustion of wood
and other fuels. CO fumes are toxic and can be fatal.
This appliance is a natural draft system which relies
on a properly designed chimney to remove CO and other
combustion by-products from the stove.
CO detectors are very sensitive and may sound an alarm
for fumes other than CO or CO from sources other than
the stove such as car or lawn mower exhaust.
If the alarm sounds
1. Increase ventilation by opening windows or doors.
2. Make sure the stove doors and lid are closed and latched.
3. Check stove for smoking or puffing condition. Open
by-pass and increase air-flow to firebox, if needed.
4. Check chimney for possible blockage or down-draft.
5. Check for false alarm.
Even though this stove is designed to be as safe as
possible, it is important that you install a CO detector.
This is true for oil, gas, or coal burning products as well.
CO is not specifically heavier or lighter than air.
Therefore, it is best to install the detector at table top level
rather than on the ceiling like a smoke detector.
Never use gasoline, lantern fuel, kerosene,
charcoal lighter fluid, or similar liquids to start
or “freshen up” a fire in this heater. keep all
such liquids well away from the heater while it
is in use.
NEvER CONNECT THIs uNIT TO a CHIMNEy
fLuE sERvINg aNOTHER aPPLIaNCE.
Installation and repair of this stove should
be done by a qualified service person. We
recommend that the stove be inspected
before use and at least annually by a qualified
service person. Periodic cleaning is required
throughout the heating season and at the end
of each winter for the stove to work efficiently.
sPECIaL NOTE:
duE TO asH BuILduP, IT Is sTRONgLy
RECOMMENdEd TO HavE yOuR sTOvE
PROfEssIONaLLyCLEaNEdaNdsERvICEd
aNNuaLLy. THIs INCLudEs aLL PaRTs Of
THE sTOvE, aNd THE vENTINg sysTEM.
dO NOT CONNECT TO aNy aIR
dIsTRIBuTION duCT OR sysTEM.
5
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
getting started
3
a. design, Installation & Location B. fire safety
Considerations
Maintain the designated clearances to combustibles.
Insulation must not touch the chimney. You must
maintain the designated air space around the chim-
ney. This space around a chimney is necessary to
allow natural heat removal from the area. Insulation
in this space will cause a heat buildup, which may
ignite wood framing. NOTE: Clearances may only
be reduced by means approved by the regulatory
authority having jurisdiction.
1. appliance Location
Consideration must be given to safety, convenience,
traffic flow, and the fact that the appliance will need
a chimney and chimney connector. It is a good
idea to plan your installation on paper, using exact
measurements for clearances and floor protection,
before actually beginning the installation. When
installing on a combustible floor, proper floor protection
material must be used. See page 12 for details.
To provide reasonable fire safety, the following should
be given serious consideration:
Maintain specified vent clearance to combustible
requirements listed by the vent manufacturers
instructions and all clearance to combustibles listed in
this manual.
1. Install at least one smoke detector on each floor
of your home. Detectors should be located away
from the heating appliance and close to sleeping
areas. Follow the smoke detector manufacturer's
placement and installation instructions, and be
sure to maintain regularly.
2. A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
3. A practiced evacuation plan, consisting of at least
two escape routes.
4. A plan to deal with a chimney fire as follows:
In the event of a chimney fire:
Check with your local building code agency before
you begin your installation. Be sure local codes do not
supersede UL specifications and always obtain the
required permit so that insurance protection benefits
cannot be unexpectedly cancelled. If any assistance is
required during installation, please contact your dealer.
We recommend that a qualified building inspector and
your insurance company representative review your
plans before and after the installation.
Be sure to provide a source of fresh air to the room
or directly to the appliance. Make-up air is needed to
replace what the chimney draws away through the
appliance.
a. Evacuate the house immediately.
b. Notify Fire Department.
c. Never apply water to a suspected chimney fire.
Serious damage could occur.
Consider attaching outside air to the appliance.
Certain conditions can create negative pressure within
the dwelling. When this occurs, you may have trouble
operating the wood stove. Worse yet, it may be strong
enough to allow smoke leakage from the appliance.
Installation on lower levels and in basements can be
especially affected.
WaRNINg
fIRE HazaRd
•
dO NOT OPERaTE aPPLIaNCE
BEfORE REadINg aNd
uNdERsTaNdINg THE OPERaTINg
INsTRuCTIONs.
CauTION
•
faILuRE TO OPERaTE PROPERLy
May CausE a HOusE fIRE.
•
•
dO NOT CONNECT THIs uNIT TO a CHIMNEy fLuE
sERvICINg aNOTHER aPPLIaNCE.
dO NOT CONNECT TO aNy fORCEd aIR dIsTRIBuTION
duCT OR sysTEM.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
C. Component Locations
Top Load Door
Top Load Opening
Bypass Damper
Control Handle
Front Load Door
Front Load
Door Latch
Bolt-Down Holes
for Mobile Home
Installations
Air Control
Ash Door
Ash Door
Latch
7
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
d. Pre- use Check List
WaRNINg
INsPECT aPPLIaNCE aNd COMPONENTs
fOR daMagE. daMagEd PaRTs May
IMPaIR safE OPERaTION.
1.
2.
Place the appliance in a location near the
final installation and follow the procedures
below:
Open the appliance and remove all articles
packed inside. Inspect all items for shipping
damage. Notify dealer of any missing or
damaged goods.
All safety warnings have been read and
followed precisely.
This Owner's Manual has been read in it's
entirety.
Floor protection requirements have been
read and followed.
The flue connector has been installed in
accordance with the instructions herein.
The proper clearances from the appliance
and chimney connector to combustibles
have been met.
•
•
•
dO NOT INsTaLL daMagEd COMPO-
NENTs.
dO NOT INsTaLL INCOMPLETE COM-
PONENTs.
dO NOT INsTaLL suBsTITuTE COM-
PONENTs.
3.
4.
5.
6.
7.
REPORT daMagEd PaRTs TO dEaLER.
8.
The masonry chimney has been cleaned
and inspected by a professional, or the
factory built metal chimney is installed
according to the manufacturers instructions.
The chimney meets the minimum height
requirements.
WaRNINg
fIRE RIsk.
9.
HEaRTH & HOME TECHNOLOgIEs
dIsCLaIMs aNy REsPONsIBILITy
fOR, aNd THE WaRRaNTy WILL BE
vOIdEd By, THE fOLLOWINg
aCTIONs:
10.
11.
12.
13.
All labels and hang tags have been removed
from the glass.
All plated surfaces have been wiped clean,
if applicable.
The optional air distribution blower
has been installed properly.
A properly grounded electrical receptacle is
available within reach of the blower's power
cord (if installed).
•
INsTaLLaTION aNd usE Of aNy daMagEd
aPPLIaNCE.
•
•
MOdIfICaTION Of THE aPPLIaNCE.
INsTaLLaTION OTHER THaN as INsTRuCTEd By
HEaRTH & HOME TECHNOLOgIEs.
INsTaLLaTION Of PaRTs OR COMPONENTs NOT
suPPLIEd OR aPPROvEd By HEaRTH & HOME
TECHNOLOgIEs.
•
•
•
•
OPERaTINg aPPLIaNCE WITHOuT THE LEgs
aTTaCHEd.
OPERaTINg aPPLIaNCE WITHOuT fuLLy
assEMBLINg aLL COMPONENTs.
dO NOT OvERfIRE.
OR aNy suCH aCTION THaT May CausE a fIRE
HazaRd.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
dimensions & Clearances
4
a. appliance dimensions
25.88"(657mm)
35.3"
(897mm)
air Intake
32.3"
(820mm)
9.1"
(231mm)
23.9"
(665mm)
Centered
26.0"
(660mm)
18.4"
(467mm)
Weight..........................................452 lbs
Flue Size........................................6 inch
Log Length Recommended........... 18"
The Harman TL2.0 meets the U.S.
Environmental Protection Agency’s
emission limits for wood heaters
sold after July 1, 1990.
Average Emissions.......................2.6 Grams Per Hr.
Outside Air size.............................4.5 inch I.D.
9
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
B. Clearances To Combustibles
vertical venting Configuration
Location
single-wall Pipe
14" / 356 mm
13" / 330 mm
24" / 610 mm
18" / 457 mm
double-wall Pipe
a
B
C
d
unit to side Wall
unit to Back Wall
vent Pipe to side Wall
vent Pipe to Back Wall
14" / 356 mm
7" / 178 mm
24" / 610 mm
12" / 305 mm
Corner Installation
16" / 406 mm
E
f
Corner to adjacent Wall
10" / 254 mm
Connector to Wall
22.5" / 571 mm
16.5" / 419 mm
d
B
C
a
f
E
f
E
*for clearance reduction methods, refer to NfPa 211 or Local Codes
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
vertical venting Configuration - Horizontal Exit
Location
single-wall Pipe
13" / 330 mm
13" / 330 mm
23" / 584 mm
18" / 457 mm
16" / 406 mm
a
B
C
d
E
unit to side Wall
unit to Back Wall
vent Pipe to side Wall
vent Pipe to Back Wall
vent Pipe to Ceiling
Corner Installation
f
Corner to adjacent Wall
16" / 406 mm
g
Connector to Wall
22.5" / 571 mm
C
E
a
2' (610 mm) Minimum vertical
prior to elbow.
d
B
g
f
*for clearance reduction methods, refer to NfPa 211 or Local Codes
11
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Minimum Size floor protection (USA) is 48" Deep By
32.5" Wide.
C. floor Protection Requirements
floor Protection
Requirements
L
Inches
Millimeters
8
18
8
203
457
203
203
Sides- USA /CANADA *
Front- USA /CANADA *
Rear- USA
j
k
L
L
Rear- CANADA
8
* Floor protection dimensions for the front and sides
are measured from the appliance door opening in
The United States. In Canada, the side dimension is
measured from the widest part of the appliance.
usa
j
j
CaNada
k
The recommended floor protection for a corner
installation is 60" (USA & CANADA).
floor Protection Requirements
If the appliance is being installed on a combustible
floor, non-combustible floor protection must be installed.
In all installations, the area under and around the stove
must be protected from falling ash and live coals. The
area under a horizontal run of chimney connector must
also be protected, extending two (2) inches (51mm) to
each side of the horizontal connector.
Further guidelines for floor protection are as follows:
In the U.S. the floor protector must be completely under
the stove, and extending 18" in front of the door opening,
8" to each side of the door opening, and 8" to the back.
In Canada, the floor protection must extend 18"
(457mm) in front of the door opening, and 8" (203mm)
to each side of the appliance, and to the rear.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
The Chimney Connector shall Not Pass Through an
attic or Roof space, Closet or similar Concealed
space, a floor or Ceiling.
Chimneys and venting
5
floor or ceiling. Whenever possible, avoid passing the
connector through a combustible wall; if you must, use
an approved wall pass-through, described later in this
section.
a. draft
Draft is widely misunderstood. It is important that
you, the stove operator, realize that draft is a variable
effect, not a given quantity. Stoves and chimneys
do not have draft, yet draft is the key to your stove’s
performance.
Assemble the connector beginning at the flue collar,
with the crimped ends pointing towards the stove (to
keep debris or residue inside the system). Each joint,
including the one to the stove’s flue collar and the one to
the chimney itself should be secured with at least three
sheet metal screws. Screws may be a maximum of 3
inches apart. A 1-1/4" (30 mm) overlap is required at
each joint, including the flue collar attachment. No more
than two 90 degree elbows should be used, and the total
length of connector should not exceed 10 feet (3 m).
All horizontal runs of connector must have a minimum
upward slope of 1/4" per foot (20 mm per meter).
Draft is a force, produced by an operating stove
and the chimney to which it is attached. It is created by
hot gases rising up the chimney, creating a pressure
difference between the inside of your home and the
outside air. It continually moves fresh combustion air
into the stove, and hot exhaust gases out of the stove;
without this constant flow, the fire will go out.
Other factors, such as barometric pressure,
winds, the airtightness of the home, the total inside
chimney volume, chimney height and the presence
of venting devices such as exhaust fans also play a
role in maintaining an adequate draft. Low barometric
pressures, super insulated homes and exhaust fans can
reduce draft; winds can play havoc with draft; and too
large or too small a chimney volume can cause reduced
draft due to the excessive cooling or not enough room
to vent exhaust gases. Introducing outside air directly
to the stove may help remedy a low draft problem.
Some signs of inadequate draft are smoking, odor,
difficulty in maintaining the fire, and low heat output.
Overdraft can be caused by a very tall chimney even if
it is the recommended size, and can cause overfiring
of your stove. Signs of an overdraft include rapid fuel
consumption, inability to slow the fire, and parts of the
stove or chimney connector glowing red. It is important
that you follow the chimney guidelines in this manual,
including size, type, and height to avoid draft problems.
When installed and operated according to this
manual, the stove will produce enough hot gases
to keep the chimney warm so that adequate draft is
maintained throughout the burn cycle.
C. Wall Pass-thrus
Depending on your local building codes, and the
pertinent provincial or national codes, there are several
choices for passing the chimney connector safely
through a wall. Before beginning your installation,
contact local officials, and also the chimney connector
and chimney manufacturer for specific requirements.
Canada. Three methods are approved by the
Canadian Standards Association. The diagram on the
next page shows one method requiring an 18"(450 mm)
air space between the connector and the wall. It allows
use of one or two covers as described in the diagram.
The two other methods are described in detail in the
current issue of CAN/CSAB365, the national standard.
United States In the U.S., the national code is NFPA
211. While many localities adopt this standard, be sure
to check with local authorities before beginning your
installation.
The NFPA(National Fire ProtectionAgency) permits
four methods for passing through a combustible wall. A
commonly used method to pass through a wall directly
to a masonry chimney is to clear a minimum 12"(300
mm) around the entire chimney connector, and fill it
with brick masonry which is at least 3.5"(90 mm) thick.
A fireclay liner, minimum 3/8" (9 mm) wall thickness
must run through the brick wall to the chimney liner (but
not beyond the inner surface of the liner). It must be
cemented in place with refractory cement. This method
is illustrated on the next page. For details on the other
three options, refer to the most recent edition of the
NFPA 211 code.
B. Chimney Connectors
In general, following these guidelines will ensure
compliance with all national and provincial codes;
prior to beginning your installation, check with your
local building code official to check on additional
local regulations which may influence the design and
placement of your venting system.
The Harman TL2.0 may be installed with a minimum
(.6 mm) 24 gauge blue or black steel, chimney connector
pipe. The size of the connector should correspond to
the size of the flue collar opening, which is 6" (152mm).
Do not use makeshift compromises. No part of the
chimney connector may pass through an attic or roof
space, closet or other concealed space, or through a
13
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Closest
Combustible
Material
Non-combustible cover, one
side only. If two covers are
used, each must be mounted
on non-combustible spacers
at least 7/8" (21mm) away
from the wall.
Minimum 2" (50mm)
Clearance to Brick
Hole with a minimum
clearance of 18" (450 mm)
between connector and wall.
Minimum 12"
Liner
(300mm) to Brick
Fire Clay
Thimble
Chimney
Connector
Masonry Chimney Built to
NFPA 211 Specifications.
1" (25mm)
Clearance
Minimum 12" (300mm)
to Combustibles
AN APPROVED U.S.
WALL PASS-THROUGH
AN APPROVED CANADIAN
WALL PASS-THROUGH
d. The Chimney
dO NOT CONNECT THIs uNIT TO a CHIMNEy fLuE
sERvINg aNOTHER aPPLIaNCE.
This unit must be installed into a chimney approved
for use with solid-fuel appliances. In the U.S., it must
be connected to (1) a prefabricated chimney complying
with the requirements for Type HT chimneys in the
Standard for Chimneys, Factory-Built, Residential Type
and Building HeatingAppliances, UL103, or (2) a code-
approved masonry chimney with a flue liner.
In Canada, this unit is listed for use with prefabricated
chimneys tested and listed to the high temperature (650
degrees C) chimney standard, ULC S-629, or with a
code approved masonry chimney.
NOTE: The restriction of not venting more than one appliance
to the same flue applies to the U.S. specifically. While it is not
recommended that you use the same chimney for more than
one appliance, in Canada certain exceptions may be made.
Be sure to contact your building code inspection official to
see if this option is allowed in your area, and to find out the
specific requirements for such an installation.
For mobile homes, (US only) it must only be installed
with a factory built stainless steel chimney. The
chimney system should include all required installation
components, such as vapor barriers and roof flashing,
as tested for use in mobile homes.
The minimum recommended height for any chimney
is 16 ft. (4.8 m) above flue collar height. For non-mobile
home installations, a round flue (either masonry or
approved prefabricated), of either 6" (150 mm), 7"
(180 mm) or 8" (200 mm) may be used. For square or
rectangular masonry chimneys, nominal sizes of 8" x
8" or 7" x 12" (200mm x 200 mm, 180 mm x 300 mm)
may be used.
More Than 10 ft. (3m)
Height Necessary
Above Any Roof Sur-
face Within 10ft. (3m)
10 ft. (3m)
2 ft. (0.6m) min.
3ft. (0.9m)
minimum
above
exit
point
Ridge
Codes require that solid-fuel chimneys extend 3 ft.
(0.9 m) above the highest point at which they exit from
the roof. Then, the chimney must extend 2 ft. (0.6 m)
above the highest point within a 10 ft (3 m) radius. Thus,
the 3 foot, 2 foot, 10 foot rule:
Chimney
The 3-foot, 2-foot, 10 foot rule
3ft. - Above roof exit point
2ft. - Higher than anything within-
10ft. of the chimney.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
1. Existing Masonry Chimneys
If you plan on using a pre-existing masonry chimney,
have it thoroughly inspected and cleaned. Any faults
which make the chimney unsafe and unusable must be
repaired prior to use. These can include improper height,
structural defects, blockages, inadequate clearance to
combustibles, unsealed openings into other rooms of
the house, signs of creosote or smoke leakage, a loose
or absent clean-out door, or absence of a liner.
2. venting to a Masonry Chimney
When connecting to a masonry chimney, several
provisions are standard. First, whether the chimney
connector is vented to the chimney through a thimble
or a breech pipe, neither must pass beyond the inner
surface of the chimney liner, and both must be firmly
cemented in place with refractory cement. (A thimble is
a masonry pipe which is inserted through the chimney
wall, and is frequently the preferred method; a breech
pipe is a piece of steel pipe used the same way.) In
Canada, a breech pipe has ridges or protrusions to lock
it firmly into the refractory cement. In either case, the
chimney connector vents to the chimney through the
thimble or breech pipe.
Using a thimble, the connector slides completely
inside the masonry to the inner edge of the flue liner,
and may be easily removed for chimney and connector
inspection. A breech pipe must extend at least 2" (50
mm) into the room, so the connector can be attached
with sheetmetal screws.
4. Installing to a Prefabricated Chimney
When venting using a prefabricated chimney, be sure
to contact local building code authorities, and to follow
the manufacturer’s instructions exactly. Use only the
manufacturer’s parts; do not use makeshift installation
techniques. All prefabricated chimneys must be
tested to either the U.S. or Canadian high-temperature
standards, UL 103 or ULC S629.
5. Other Considerations
3. venting to a Masonry fireplace Chimney
Do not burn any fuel other than dry cordwood. Never
use highly volatile substances in your stove, such as
gasoline, which could cause an explosion.
In some situations, a code compliant chimney originally
used for a masonry fireplace may be used. In addition
to the requirements found in the previous paragraphs,
it is important to be aware that all clearances must be
met, including those from the chimney connector to
combustibles. Do not forget to include floor protection
in your plans. (See Clearances and Floor Protection
in this section.) Since many fireplaces have exposed
wooden mantels and trim, pay special attention to the
clearances necessary to these materials.
When solid fuels are burned completely, they produce
water and carbon dioxide. However, in long slow
burns, a substantial amount of carbon monoxide may
be produced. If allowed to build up, carbon monoxide
(which is odorless) can prove fatally poisonous. Proper
ventilation and draft will prevent this from happening.
If you smell smoke, thoroughly ventilate your dwelling,
and contact your dealer for service.
If your fireplace chimney is behind a combustible wall,
you must use an approved wall pass-through system
to gain access to the masonry chimney. The chimney
connector must enter the chimney at a place where it is
lined, and the fireplace must be made inoperable. For
example, you might remove the damper, replacing it with
a secure, airtight, noncombustible seal (removable for
inspection); this also satisfies the requirement that no
room air must be allowed to enter the chimney.
Other causes of poor ventilation or draft are icing,
exhaust fans, a blocked outside air inlet, and room
air starvation. If your stove is sluggish and you get
occasional odor, check these possibilities and increase
the air flow in your home.
THE CHIMNEy aNd CONNECTOR MusT BE
MaINTaINEd IN gOOd CONdITION aNd kEPT
CLEaN.
15
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
standard Ceiling Installation with factory Built Chimney
Chimney Cap
Chimney
sections
storm Collar
Roof flashing
Roof
Radiation
shield
attic
Radiation
shield
Minimum air space
with Chimney
Listing
Chimney
support
Chimney
Connector
The Chimney Connector shall Not Pass Through an attic or Roof
space, Closet or similar Concealed space, a floor or Ceiling.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Cathedral Ceiling Installation with factory Built Chimney
Chimney Cap
Roof Radiation
Factory-Built
Shield
Metal Chimney
Sealed Storm Collar
Roof Flashing
Cathedral Style
Chimney Support
Finishing
Collar
Chimney
Connector
17
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Chimney Breach fireplace Conversion with Non-Combustible Wall
Minimum Clearance
to unprotected Ceil-
ing 16"
Chimney Connector
sealed at Thimble
flue Liner with Re-
quired air space
Three sheet Metal
screws per joint of
Chimney Connector
airtight
insulated
Clean-out
Mantel and Trim Pro-
tection
amper
losed and
ealed with
on-Combus-
ble Material.
floor Protection*
Combustible floor
* floor Protection in accordance
with solid fuel appliance Listing
The Chimney Connector shall Not Pass Through an attic or Roof space, Closet
or similar Concealed space, a floor or Ceiling.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Chimney Breach Fireplace Conversion with Combustible Wall
Minimum Clearance from
Chimney Connector to Un-
protected Ceiling
16"**
Flue Liner with Required Air Space
Listed or Approved Thimble Assembly
Combustible
Wall
1" Clearance for Complex-
ity Exterior Chimney
or
2" Clearance for Interior
Chimney and 2" Clear-
ance for NFPA 211-Type
Approved Thimbles
Sheetrock
Airtight
insulated
Clean-out
Mantel & Trim
Protection
Damper Closed and
Sealed with Non-
Combustible
Material.
Floor Protection*
Combustible Floor
* Floor Protection in Accordance with Solid Fuel Appliance Listing
** Check with your local building codes for clearance.
The Chimney Connector shall Not Pass Through an attic or Roof space, Closet or similar
Concealed space, a floor or Ceiling.
19
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Mobile Home
6
NOTE: The top sections of the chimney must be
removable to allow a maximum clearance of 13.5 feet
(411cm) from ground level for transportation purposes.
a. Mobile Home Installation
Mobile home approval - u.s. only.
dO NOT INsTaLL IN a MOBILE HOME IN CaNada.
1. An outside air inlet must be provided for
combustion air, and must remain clear of leaves,
debris, ice, and/or snow. The outside air path must
be unrestricted while the appliance is in operation.
Use Kit #1-10-856082 to attach to unit.
2. The combustion air intake system must be of
metal construction. It must permit zero-clearance
to combustible materials, and contain a rodent
screen.
3. The appliance must be secured to the mobile
home structure by bolting it to the floor. There are
holes provided in the pedestal base. Secure with
the proper length lag bolts, through the hearth pad
and into the home floor.
Chimney Cap
Storm Collar
Chimney
Sections
Roof Flashing
Roof
Radiation
Shield
Attic
Radiation
Shield
4. The appliance must be grounded to the metal
framing of the mobile home
5. All clearances to combustibles and floor protection
requirements must be followed.
Minimum Air Space
with Chimney Listing
Chimney
Support
6. Follow the vent manufacturer's instructions when
installing in a mobile home. Must be connected to
a UL103 HT ventillated chimney connector, UL103
HT chimney, and terminal cap with spark arrestor.
7. Use silicone to create an effective vapor barrier at
the location where the chimney or other component
penetrates to the exterior.
Chimney
Connector
8. Installation shall be in accordance with the
Manufactured Home and Safety Standard (HUD)
CFR 3280, Part 24
9. The appliance must never be installed in a room
designated for sleeping.
Outside
Air
10. Burn wood only. Other fuels may generate
poisonous gases (carbon monoxide).
11. If unit burns poorly while an exhaust blower
(range hood) is operating, increase the supply of
combustion air to the appliance
WaRNINg
CauTION
THE sTRuCTuRaL INTEgRITy Of THE MOBILE HOME
fLOOR, WaLLaNd CEILINg/ROOf MusT BE MaINTaINEd.
INsTaLLaTION MusT COMPLy WITH
MaNufaCTuREd HOME aNd safETy sTaNdaRd
(Hud), CfR 3280, PaRT 24.
dO NOT CuT THROugH:
•
•
fLOOR jOIsT, WaLL sTuds, OR CEILINg TRussEs.
aNy suPPORTINg MaTERIaL THaT WOuLd affECT
THE sTRuCTuRaL INTEgRITy.
WaRNINg
dO NOT INsTaLL IN sLEEPINg ROOM.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
appliance set-up
7
a. Outside air attachment
B. Leveling the appliance
Use metal shim material under the pedestal base
where needed for leveling.
Parts and Supplies Needed: Kit #1-10-856082, 1
piece of metal flexible pipe, 4" X needed length. 1
Rodent Screen, and aluminum tape. Plus, a trim ring
for finishing around the pipe on the inside wall.
1. Determine an appropriate hole location, through
the wall. Be sure there are no studs or other
supporting members. Also ensure there are no
electrical wires or plumbing contained within the
wall.
2. Make the hole through the exterior wall using a
hole saw or reciprocating saw. You'll want the hole
to be just slightly larger than the metal flex pipe.
3. Attach the rodent screen to one end of the flex
pipe, and insert it through the wall until the back
of the screen cover is against the outside surface.
4. Hold the flex pipe in place to make an accurate
determination of the length needed. Cut the flex
pipe to length.
C. Optional Cooking grill
The optional cooking grill #1-00-08121 installs easily
in the top load opening of the stove.
The grill handle (B) fits in the slots (C) on each side. To
remove the handle, lower and turn.
When installed, the grill hangs in the opening by the
hooks (A).
5. Slide the trim ring onto the flex for the inside wall
portion.
a
6. Slide the other end of the metal intake flex pipe
into the stub on the rear of the stove and secure
it with aluminum tape. This air intake will supply
outside air for the secondary combustion.
7. Secure the trim ring in place for finishing the inside
wall area.
B
a
8. Seal around the rodent screen on the exterior wall,
using silicone caulking.
C
CauTION
NEvER dRaW OuTsIdE COMBusTION aIR fROM:
C
•
•
WaLL, fLOOR OR CEILINg CavITy.
ENCLOsEd sPaCE suCH as aN aTTIC OR gaRagE
a
When grilling, you'll want to keep the fire size small and
the bypass damper in the open position. Depending on
the grilling being done, you may get grease dripping
on the glass causing it to become dirty and obstructed.
When you burn your next hot fire, the glass will likely
clean itself.
kEEP TOP LOad dOOR CLOsEd ExCEPT WHEN
LOadINg OR uNLOadINg gRILL.
Outside Air
Attachment
21
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
d. Optional Blower Installation
E. Top air grill Option
use ONLy Blower Part #1-00-856002 With This
appliance.
The optional blower kit installs easily to the rear of
the TL2.0. First, remove the air jacket shield from the
rear of the stove. Use the same four bolts to attach
the blower as shown.
The top air grill installs over the flue collar and simply
rests on the top of the stove. The brushed stainless
grill is included with this option as well.
f. Brushed stainless Trim kit Option
WaRNINg
ROuTE POWER CORd aWay fROM THEaPPLIaNCE.
dO NOT RuN THE CORd uNdER OR IN fRONT Of
THE aPPLIaNCE.
The trim kit consists of three pieces; Load door trim,
Ash lip trim, and the Ash door frame. To install the load
door trim, it is best to remove the door by lifting from
the hinges. lay the door down flat on it's face. Drill the
dimpled holes in each corner of the door and re-install
the door onto the stove. From the outside, install the
frame with the studs going through the newly drilled
holes and install the nuts on the inside. To install the
ash lip trim, just slide it onto the ash lip. You may attach
with silicone if desired. The ash door frame uses a
spring clip on one end to hold it into the recessed area
of the ash door. Install the clip in the frame channel
and push that end into the door opening until the other
end of the frame fits.
Plug the blower into a properly grounded electrical
outlet.
Keep the blower on low speed or off during low fires.
As you get out of the low burn range, the speed can
be set wherever desired, or kept off.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Operating Instructions
8
CauTION: approved for use with wood fuel only.
The use of any other fuel will void the product
warranty and may cause damage to the appliance
and/or your home.
B. general Operating Information
1. draft Before you install and/or operate your
wood stove, please read the entire contents of this
manual. Pay particular attention to the explanation
of draft and its effect on stove performance in
the Installation section. By following the installation
and operating guidelines, you will ensure proper draft
and gain maximum efficiency and enjoyment from your
stove.
WaRNINg
"NEvER usE gasOLINE, gasOLINE-TyPE LaNTERN
fuEL, kEROsENE, CHaRCOaL LIgHTER fLuId, OR
sIMILaR LIquIds TO sTaRT OR "fREsHEN uP " a
fIRE IN THIs HEaTER. kEEP aLL suCH LIquIds
WELL aWay fROM THE HEaTER / fIREPLaCE
sTOvE WHILE IT Is IN usE".
dO NOT aLTER THE POsITION Of THE aNdIRONs.
BuILdINg a fIRE TOO CLOsE TO THE gLass May
CausE daMagE TO THE gLass, CREaTINgasERIOus
RIsk Of fIRE aNd PROPERTy daMagE.
a. fuel specifications
Select only dry, seasoned wood. Wood for burning
should never be exposed to rain or extremely damp
conditions. Hardwoods are favored because they are
heavier and contain more heating capacity (BTU’s) per
load than do softwoods. Fuel wood should be split and
stored under cover for “seasoning” - at least a year is
recommended. Your stove is not an incinerator - do
not burn garbage, painted or treated wood, plastic, or
other debris.
Keep the area around the stove free from clutter.
Keep all combustibles, including fuel, beyond the code-
required clearance distance (48" or 1215 mm in the
U.S., 1525 mm or 60" in Canada). Never store fuel
in front of the stove where it could interfere with door
operation, safe loading, and ash removal.
2. doors Your stove has a large glass-paneled door
for loading and fire viewing, a separate smaller door
for removing ashes and a top loading door.
Front Door
Before opening, always check for wood, embers, or
ash that may be ready to fall out of the door.
To open the glass door, open the bypass damper first,
then turn the handle clockwise and pull out; to close
the door, push the door closed with the handle in the
open position, then turn, counter-clockwise, to engage
the latch.
Ash Door
To open the ash door, lift up the handle and pull out.
Close the door by pushing in and pushing the handle
all the way down.
Top Load Door
To open the top load door, open the bypass damper
and then lift to open the top load door.
CauTION:
aLWays WEaR fIRE RETaRdaNT gLOvEs
WHEN OPERaTINg THE sTOvE.
All doors must be closed while the stove is in normal
operation, and the gaskets routinely examined for wear
and replaced when necessary. Good door seals are
important for maintaining control of the stove. Never
operate with the ash door open. Operating the stove
with the ash door open, or with a door inadequately
sealed, could create a serious overfiring condition
(discussed later in this section).
The glass used in your stove is manufactured to exact
standards to withstand the high heat of the fire, but like
all glass, it must be treated with common sense and
care. Never abuse the glass by slamming the door
shut or striking the glass with a heavy object. If the
glass is broken or damaged, do not operate the stove
until it has been replaced
safETy NOTICE
If THIs aPPLIaNCE Is NOT PROPERLy INsTaLLEd,
OPERaTEd aNd MaINTaINEd, a HOusE fIRE May
REsuLT.fORyOuRsafETy,fOLLOW INsTaLLaTION
dIRECTIONs. CONTaCT LOCaL BuILdINg OR
fIRE OffICIaLs aBOuT REsTRICTIONs aNd
INsTaLLaTION INsPECTION REquIREMENTs IN
yOuR aREa.
dO NOT BuRN gaRBagE OR fLaMMaBLE LIquIds
suCH as gasOLINE, NaPTHa, OR ENgINE OIL.
(See instructions in the Maintenance section.)
23
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
3. grates
d. The Combustion Process
The unique grate system consists of one flat bottom
grate, and two front andirons. The bottom grate has
slots which allow the ash to fall into the ash pan by
passing a poker back and forth across the grate. The
andirons keep the fuel from coming into direct contact
with the glass, and keep hot coals and embers from
spilling out while reloading. Never build a fire directly
against the glass.
Combustion in the firebox is precisely controlled and
is best explained in two parts.
During a wood fire, combustion air enters at the
bottom front of the stove where it travels upward through
channels at either side of the front door. From the
manifold located above the front door, it is directed into
the firebox as a sheet of air flowing between the glass
and the wood. This concept helps to keep the glass
clean, while providing the oxygen needed to sustain
burning. This is what is known as "Primary Combustion".
The grates and andirons must remain in place
at all times. do not tamper with or change the
configuration of this grate system.
Additional air enters at the bottom rear of the stove
body. Some of this air enters through holes in the
rear bricks where it is used to revitalize the fire at the
rear of the firebox. The remainder is delivered into
the "Firedome Plus" combustion package where the
"Secondary Combustion", or re-burning of the smoke,
occurs.
C. Burning as a fireplace
This appliance has been tested and approved for
burning as an open fireplace. To do so, a spark screen
(Harman part# 3-40-06960; Cozy Screen) must be
installed over the front door opening. The by-pass
damper must be kept in the open position.
During combustion, the burning of wood proceeds
through several stages. The initial or evaporation
stage is where the moisture in the wood is driven off
in the form of steam. A second stage is where the
volatile gases contained in the wood are released and
burned. This represents most of the wood's heating
capacity. The final stage is the charcoal stage where
the charcoal burns the remaining heat content in the
wood fuel. Ash remains after the burning is complete.
Within the primary firebox two or more of these stages
of combustion are occurring at once.
The Cozy Screen can
be used from the start
of a fire or can be used
with an existing one.
When starting a fire
with the Cozy Screen,
smoke spillage may
occur until it develops
a draft strong enough to
pull all smoke back into
the flue.
Always be sure to provide adequate ventillation to
the room where the apliance is located, to prevent
air starvation. In tight construction, consider installing
outside air to the appliance.
DO NOT LEAVE THE APPLIANCE UNATTENDED
WITH THE DOOR OPEN!
Load only small amounts of wood at a time.
EXHAUST STREAM
SECONDARY AIR
THRU BRICK
SECONDARY AIR ENTERING
PRIMARY AIR FLOW
EXHAUST STREAM
SECONDARY AIR FLOW
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
For low burn, slide the air control to the left. For
medium burns, use notches 1 to 2. Maximum heat is
attained with the air control all the way to the right. Do
not burn the stove continuously at the maximum setting.
If maximum heat is required day after day, the stove is
too small for the area you are trying to heat.
If your wood is not seasoned long enough or is high
in moisture content, you may need to adjust the primary
air slightly higher to sustain a low burn rate with the
cleanest possible exhaust.
E. user Controls
Two important controls - the damper bypass handle
and the air control lever regulate the operation and
output of the stove.
To open the top or front loading door, you must open
the damper bypass, or smoke will come in the room. In
this mode of operation the combustion gases go directly
from the main combustion chamber to the flue collar
and exit into the chimney.
NOTE: The bypass damper must be open for
smokeless loading. Open the bypass damper by
turning the handle clockwise while facing handle.
f. Before your first fire
•
Be sure the appliance is installed properly and
that all safety requirements have been met.
Pay particular attention to the clearances to
combustibles, floor protection and the venting
instructions.
•
•
•
Test your smoke detector(s) and CO detector(s) to
the specifications of the manufacturer.
Double check that the ash pan and internal firebox
are empty.
damper Open
damper Closed
Be sure to read this entire manual.
CauTION! dO NOT OvERLOad THE aPPLIaNCE. If
yOu CaN NOT CLOsE THE LId OR dOOR, yOu HavE
OvERLOadEd.
Begin with the bypass damper open, and the air
control lever at the maximum setting, all the way to the
right. Be sure the ash pan door is closed and latched.
Start with a bed of crumpled paper and kindling sized
about finger width; place several 1" - 2" (25mm - 50mm)
split pieces of dry wood on top of the kindling, followed by
a few 2" - 3" (50 mm - 80 mm) split pieces. Lay the wood
in a crossed pattern to allow maximum air flow. Ignite
thepaper and close the loading door(s).Allow this start-
up fire to burn for a few minutes, keeping the bypass
damper open. Add about five more pieces of wood in
the 2 to 3 inch (50 - 80mm) size range, making sure
that the fuel bed is all the way across the firebox and
staggered to allow airflow. Close the door and allow this
loading to burn a few minutes.
Minimum
Primary Air
Maximum
Primary Air
The air control lever is located on the ash lip, below
the load door. Sliding this lever allows you to vary the
amount of air to the fire, creating a range of heat out-
puts. The lowest heat output setting is to the left, and
the highest is to the right. The notches are provided as
a reference for your comfortable heat settings. Do not,
under any circumstances, alter the configuration or op-
eration of the air control lever.
Add increasingly larger pieces of wood to the fire until
you have a thick bed of hot embers, approximately 2
to 3 inches deep at the back of the grate and at least
an inch deep at the front. You must have this charcoal
bed established before you close the bypass damper.
25
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Providing you have the charcoal bed described,
close the bypass damper by pulling the handle toward
the front of the stove. This will begin the highly efficient
mode of operation where the exhaust gases get re-
burned in the secondary combustion package. If you
cannot achieve a charcoal bed within the first 15 to 20
minutes, your wood is likely too wet, and you may need
to burn the fire longer and/or hotter to compensate for
the extra energy needed to drive out the moisture. If,
after five minutes of burning with the damper closed,
smoke is visible coming from the chimney, you probably
do not have the proper coal bed. Open the bypass
damper and continue with the process until a significant
coal bed is formed.
dIsPOsaL Of asHEs;
ashes should be placed in a steel container with
a tight fitting lid. The container of ashes should
be moved outdoors immediately, and placed on a
noncombustible floor or the ground, well away from
all combustible materials, pending final disposal.
If the ashes are disposed of by burial in soil or oth-
erwise locally dispersed, they should be retained
in the closed container until all cinders have com-
pletely cooled. Other waste shall not be placed in
this container.
CauTION
HOT WHILE IN OPERaTION. kEEP CHILdREN,
CLOTHINg aNd fuRNITuRE aWay. CONTaCT May
CausE skIN BuRNs.
Always remember to open the bypass damper when
you are loading, this allows the exhaust gases to pass
directly into the flue outlet and reduces the chance of
smoke spillage into the room.
NEvER LEavE THE sTOvE uNaTTENdEd If EITHER
THE asH OR LOad dOOR Is OPEN. OvERfIRINg
May REsuLT.
Reloading: Onceyouhavepreparedandmaintained
a thick charcoal bed, and the secondary combustion is
established, you should be able to reload the stove at
any time by simply opening the bypass damper, then
the load door, adding fuel and closing the door then the
damper. This depends on coal bed size, load size and
moisture content of fuel.
RIsk Of ExCEssIvE TEMPERaTuREs. kEEP asH
dOOR CLOsEd duRINg fIRINg Of THE HEaTER.
Avoid overfiring your stove. Overfiring is a potentially
hazardous situation which can lead to overheating of
combustible materials nearby, damage to the stove, and
in extreme cases, cause a fire. Overfiring is caused by:
1. Too much air flowing through the stove too quickly. 2.
You may have positioned the primary air control lever
too far to the right. 3. Inadvertently leaving the damper
open or 4. Not keeping up with routine maintenance,
such as checking door gaskets for wear.
Overfiring results in excessive fuel consumption, and
may cause parts of the stove or chimney connector to
glow red. If you notice signs of overfiring, reduce the air
supply to the fire, and review the Maintenance section
in this manual.
In the event of a chimney fire, call your local fire
department; make sure everyone is safely out of the
house. Reduce the air intake of the stove as much as
possible using the air control lever; close the bypass
damper to further restrict air flow. Do not throw water
on the fire; this can cause stove damage and create
an even more dangerous situation. Have your chimney
professionally cleaned and inspected before resuming
burning in your stove.
Removing ashes: Before reloading, empty the ash
pan (remember to close the ash door while emptying
the pan). The ashes should be the coolest at this time.
Remove ashes from the fire chamber periodically by
raking a poker across the bottom grates.
Excessive ash buildup can prevent proper venting
of exhaust gases. Do not allow the ash pan to over-fill.
Ash buildup between the ash pan and the bottom of
the grate can cause the grate to overheat and wear
out prematurely.
The TL2.0 is designed to provide access to the ash
pan without the need for opening the main door. Before
opening the ash door
and removing the ash
pan, open the bypass
damper. Wearing
heavy protective
gloves, open the ash
door and remove the
ash pan by pulling
it forward by the
handle. Close the
ash door and damper
bypass before taking
the ashes outside for
safe disposal.
As you begin to operate your stove at higher
temperatures, you will notice a “hot” or unpleasant
smell; this is just the paint going through the curing
process, and will disappear after a few fires.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
solid fuel burning spave heaters must be cleaned regularly,
as soot, ash and creosote may accumulate.
service & Maintenance
9
seasonal cleaning
a. Creosote- formation and Need for Removal;
At least once per year, the stove, venting connectors
and chimney should be thoroughly cleaned. If the
areas are found to have an excessive build up of ash or
creosote, it is recommended to increase the frequency
of the cleaning. This will extend the life of the appliance
and its components.Avacuum specifically designed for
ash is preferred, however a standard shop-style vacuum
with a HEPA filter may also work just fine.
When wood isburned slowly, itproduces tarand other
organic vapors which combine with expelled moisture
to form creosote. The creosote vapors condense in the
relatively cool chimney flue of a slow burning fire. As a
result, creosote residue accumulates on the flue lining.
When ignited, this creosote makes an extremely hot
fire. The chimney and chimney connector should be
inspected at least once every two months during the
heating season to determine if a creosote buildup has
occurred. If creosote has accumulated, 3mm or more,
it should be removed to reduce the risk of a chimney
fire.
During cleaning, caution must be taken not to damage
the white / gray colored ceramic combustion package
in the rear of the firebox. When using a brush in the
chimney or venting connector, the by-pass damper
should be placed in the open position to help prevent
ash, creosote or other debris from falling down onto
and around the combustion package. This also protects
the top of the combustion package from tool or brush
damage and diverts most of the removed materials
into the firebox for easy clean-up and removal. Once
the venting system has been cleaned, remove the first
section of connector pipe from the appliance flue collar.
Carefully vacuum the ash and debris from around the
sides and top of the combustion package.
If you experience a chimney fire; Close the
air control and bypass damper and notify the fire
department. Do NOT apply water to the fire, in the
firebox or in the chimney. Do not operate the appliance
until the chimney and connector have been inspected
and approved by a chimney professional.
Do not burn any fuel other than wood, such as char-
coal, which can cause increased carbon monoxide
production or overfiring. Never use highly volatile sub-
stances in your stove, such as gasoline, which could
cause an explosion.
The shoe brick must be removed to allow vacuum
access for cleaning the front portion of the combustion
package.
When solid fuels are burned completely, they pro-
duce water and carbon dioxide. However, in long slow
burns, a substantial amount of carbon monoxide may
be produced. If allowed to build up, carbon monoxide
(which is odorless) can prove fatally poisonous. Proper
ventilation and draft will prevent this from happening.
If you smell smoke, turn up the air control lever setting,
and thoroughly ventilate your dwelling. During future
burns, be careful not to overload the stove with fuel, so
you will not be tempted to constantly operate at a low
air control setting.
Alwaysusecautionwhenrefuelingorwhenvacuuming
the firebox and combustion package. Some users have
damaged their combustion package with vacuum
cleaner tools, and fire pokers.
CAuTion: ALwAys weAr Fire-resisTAnT
gLoves To operATe The sTove. The Air
ConTroL is hoT whiLe in operATion.
Other causes of poor ventilation or draft are icing,
exhaust fans, a blocked outside air inlet, and room air
starvation. If your stove is sluggish and you get occa-
sional odor, check these possibilities and increase the
air flow in your home.
27
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
2. door glass
B. general Maintenance Procedures
1. ash Removal
•
•
frequency: As needed / Weekly
By: User
•
•
frequency: As needed / Every day or two
By: User
Whenever the view of the fire is obstructed, or week-
ly, clean the glass using a soft cloth dampened with
standard household glass cleaner.
Wear Leather gloves To Prevent skin Burns!
CauTION! dO NOT CLEaN gLass WHEN HOT.
allow glass to cool before cleaning.
Open the ash removal door by lifting upward on the
latch handle, then swing the door open. Pull the ash
pan out of the firebox, using the lip on the front of the
pan. Once the ash pan is removed from the stove,
you can flip the carry handle up for convenience.
If removing ashes while a fire is burning, close and
latch the ash door while disposing of the ashes.
DO NOT leave the appliance unattended with the ash
door open.
fly-ash allowed to accumulate on the glass may
lead to permanent fogging or "crazing" of the
glass.
Inspect the glass and sealing gasket. Replace gasket
as needed. Do not operate the stove with a broken
glass. Replacement glass, which is ceramic glass,
should be obtained only through your Harman dealer.
To replace a broken glass; first be sure to carefully
remove the broken glass and any remaining shards
or pieces. With the door laying on a flat surface, lay
the gasketted glass panel onto the door and be sure
it is properly fitted into the channel. Lay the glass
retainer clips in place near each corner, and secure
them using the 3/8" screws. Be sure to tighten each
screw equally so you don't create a pressure point on
the glass.
WaRNINg! do NOT use substitute Material for
glass Replacement.
CAuTion: never use AbrAsive mATeriALs
on The gLAss.
Glass Retainers
Glass Retainer
screws
Glass Panel
dIsPOsaL Of asHEs;
ashes should be placed in a steel container with
a tight fitting lid. The container of ashes should
be moved outdoors immediately, and placed on a
noncombustible floor or the ground, well away from
all combustible materials, pending final disposal. If
the ashes are disposed of by burial in soil or oth-
erwise locally dispersed, they should be retained
in the closed container until all cinders have com-
pletely cooled. Other waste shall not be placed in
this container.
Glass Gasket
Door Frame
glass specifications: 5mm x 419mm x 314mm arched.
WaRNINg: dO NOT aBusE gLass By sTRIkINg
OR sLaMMINg THE dOOR CLOsEd. THIs TyPE Of
BREakagE Is NOT COvEREd By THE PROduCT
WaRRaNTy.
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
3. firebox
5. Chimney Connector
•
•
frequency: As necessary / Yearly
By: User
•
•
frequency: As necessary / Yearly
By: Qualified Service Technician / User
Cleaning the firebox and internal heat exchange
surfaces is recommended to maintain thermal
efficiency. Depending on the quality and quantity of
fuel being used, you may want to perform this cleaning
monthly.
At the end of the burn season, brush and clean all
sections of chimney connector pipe. Some owners
remove the chimney connector for the off season.
Any ashes left in the connector pipe will actually draw
moisture which promotes rust. This is why it is very
important to clean all ashes at the end of the heating
season.
Be sure to clean these areas thoroughly at the end of
the heating season.
When cleaning the chimney connector above the
appliance, keep the bypass damper in the open
position. This will keep any loosened material from
falling into the Firedome Plus combustion chamber.
Brush and vacuum all internal surfaces at the end of
the heating season. Ashes will draw moisture and may
promote rust formation.
4. Blower- If installed
•
•
frequency: As necessary / Yearly
By: User
Chimney
Connector
The fan on the blower will collect pet hair and other
debris over time. Any accumulation must be removed
to maintain proper operation.
To clean blower;
•
•
•
disconnect Power Cord Before servicing.
Remove the four bolts that hold the blower in place.
You will find it easiest to use an air hose and blow
the debris from the blower housing.
Alternately, with some minor disassembly, you can
use a vacuum and/or brush to clean the blower
wheel.
•
•
6. Chimney
•
•
frequency: As necessary / Yearly
By: Qualified Service Technician / Chimney Sweep
Reinstall the blower and tighten the four bolts
securely.
The entire chimney should be professionally cleaned
at least once yearly. It is best to have this done at
the end of the heating season to be sure all ash is
removed. You'll also want to inspect the condition of
the chimney prior to using the appliance, to be sure
there are no bird or animal nests.
29
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
Reference Materials
10
1
2
Dry Seasoned Wood Only!
3-90-08560
Save These Instructions
30
Download from Www.Somanuals.com. All Manuals Search And Download.
service Parts
TL2.0
Beginning Manufacturing date: sept 2011
Wood stove
Ending Manufacturing date: active
1-90-856000-1 Black W/Pedestal
1
2
7
8
6
9
4
3
10
13
26
25
11
12
14
15
16
22
24
20
19
23
17
21
18
Part number list on following page.
09/11
Download from Www.Somanuals.com. All Manuals Search And Download.
service Parts
TL2.0
Beginning Manufacturing date: sept 2011
Ending Manufacturing date: active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
stocked
at depot
ITEM
dEsCRIPTION
Top load door, painted w/gasket & hdwr
Top load door gasket
COMMENTs
PaRT NuMBER
1-10-856009A
1-00-10050
1
y
y
5 ft
Hinge spacer
Qty 2 req
30 ft
2-00-40021L
1-10-250109A
1-00-00888
2
Damper frame asy with damper
Damper gasket
y
y
Damper adjuster with hardware
Gasket, 1" Single Ply Tape
Firedome Plus Combustion Package
Gasket, brick air
1-00-250153
1-00-88100
10 Ft
y
y
y
y
y
y
y
y
y
y
y
y
y
y
3
3-40-358110
3-44-2500202-4
1-00-249153
1-00-00249
Pkg of 4
Pkg of 2
Pkg of 2
4
6
Rear brick clips with hardware
Wooden handle for damper w/hardware
Damper handle, painted
Damper shaft bushing plates w/hardware
Damper rod weldment
Left side panel, painted
Inlet brick
7
3-50-00500S
1-00-856061
1-10-856011W
2-00-856023B
3-40-358112
1-00-358118
1-00-856077
2-00-856013B
1-00-856010
1-10-06920A
1-00-249119
1-00-2312
8
Inner & outer
9
10
11
12
13
14
15
16
Brick Air Plate
Set of 2
6 pc set
Side & rear firebrick
Ash grate
Andiron with hardware and extensions
Front load door asy, painted with glass
Door latch, painted w/hdwr & handle
Glass gasket
y
y
y
y
15 ft
30 ft
Door gasket
1-00-00888
Glass only
3-40-06932
Latch plate, roller & hardware
Ash door asy, painted with handle
Ash door latch only
1-00-06903
17
1-10-856005A
3-00-249149
1-00-10000
Ash door gasket
5 ft
y
Ash door hinge with hardware
Ash door roller with hardware
Air slide rod bracket with hardware
Air control weldment
1-00-856020
1-00-06902
18
19
20
21
22
1-00-856008
1-10-856004W
1-10-856003W
1-10-856006A
3-40-00100
y
y
y
y
y
y
Air slide
Ash pan
Combustion shoe brick
Shoe brick gasket
3-44-06951
Additonal service parts on following page
09/11
Download from Www.Somanuals.com. All Manuals Search And Download.
service Parts
TL2.0
Beginning Manufacturing date: sept 2011
Ending Manufacturing date: active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
stocked
at depot
ITEM
23
dEsCRIPTION
COMMENTs
PaRT NuMBER
3-40-856086
2-00-856024B
2-00-856026B
1-00-856025
1-00-856019
2-00-358150B
1-00-856027
Side brick insulation
Qty 2 req
y
y
24
Right side panel, painted
Heat shield mounting plate, painted
Rear heat shield, painted with hardware
Blower Blockoff
25
26
y
Combustion Package Cap
Brick Retainers
y
y
Set of 2
Hardware Packages
#10-24 x 1/4" Alloy Steel Black Oxide Cup Point SSS
Acorn Nut, 10-24 Nickel Plated
Pkg of 100
Pkg of 50
Pkg of 3
3-30-2006-100
3-30-8014-50
3-31-5500-3
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
Ball Plunger, 5/16 x 1/2
Bolt, Case Hardened Zinc Flange, 1/4-20 x 3/8
Bolt, HCS 3/8-16 x1 1/4
Pkg of 50
Pkg of 25
Pkg of 50
3-30-2000-50
3-30-1135-25
3-30-2001-50
3-30-1119-25
3-30-1109-50
3-30-1113-50
3-30-1110-100
3-30-1122-50
3-30-1106-25
3-30-1126-50
3-30-2005-15
3-30-8019-100
3-30-6007-25
3-30-6005-100
3-30-8020-100
3-30-8005-100
3-30-8004-100
3-30-8021-50
3-30-7900-100
3-30-3011-100
3-30-2004-25
3-30-1101-100
3-30-1111-50
3-30-3014-100
3-30-0205-50
Bolt,1/4-20 x 1/2" Grade 8.2 Zinc SAE Flange
Cap Screw, 1/4-20 x 1 1/2 Grade 8 Yellow Zinc Hex Head Pkg of 25
Cap Screw, 1/4-20 x 1/2 Grade 8 Yellow Zinc Hex Head
Cap Screw, 1/4-20 x 3/4 Grade 8 Yellow Zinc Hex Head
Cap Screw, 1/4-20 x 5/8 Grade 5 Zinc Hex
Pkg of 50
Pkg of 50
Pkg of 100
Pkg of 50
Pkg of 25
Pkg of 50
Pkg of 15
Pkg of 100
Pkg of 25
Pkg of 100
Pkg of 50
Pkg of 100
Pkg of 100
Pkg of 50
Pkg of 100
Pkg of 100
Pkg of 25
Pkg of 100
Pkg of 50
Pkg of 100
Pkg of 50
Cap Screw, 5/16-18 x 1/2" Grade 5 Zinc Plated Hex
Cap Screw,1/4-20 x 3/8" Grade 5 Zinc Hex
Cap Screw,5/16"-18 x 3/4" Grade 8 Plain Finish Hex
Dowel Pin, 3/16 x 2" Bright Finish Steel
Lock Nut, 10-32 Grade A Zinc Plated Top
Machine Screw, 1/4"-20 x 2 1/2" Phillips Round Head Zinc Pltd
Machine Screw, 10-32 x 3/8" Phillips Round Head Zinc Plated
Nut , Centerlock,1/4-20
Nut, Grade 5 Zinc Plated Finished Hex, 5/16"-18
Nut,1/4"-20 Zinc Plated Finished Hex
Nut,1/4-20 Grade C Zinc Plated Top Lock
Rivet, 1/8" Dia .032-.062" Grip Range AB4-1CLD Alum
Screw, #10-24 x 3/8" Alloy Steel Black Oxide Button Head Cap
Screw, 5/16"-18 x 3/8" Alloy Steel Black Oxide Knurled Point SSS
Screw, BLK OX, HWH TCS 10-24X1/2
Screw, Hex Washer Slot T23 Zinc Thread Cutting ,1/4-20x5/8"
Screw,1/4"-20 x 3/8" Alloy Steel Black Oxide Button Head Cap
Washer, 5/16" Zinc Plated SAE Flat
09/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufactured by: HeartH & HoMe tecHnologies, inc.
Model: tl2.0
u.s. enviroMental Protection agency
Meets EPA particulate matter (smoke) control requirements for
noncatalytic wood heaters built on or after July 1, 1990.
sMoKe
0
8.5
grams Per Hour
efficiency
50%
60%
70%
80%
90%
100%
Wood heaters with higher efficiencies cost less to operate.
Heat outPut
9,600 to 31,800 btu
use this to choose the right size appliance for your needs.
asK dealer for HelP.
this wood heater will achieve low smoke output and high efficiency
only if properly operated and maintained. see owner’s manual.
#3-90-856
Download from Www.Somanuals.com. All Manuals Search And Download.
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts Labor
HHT Manufactured Appliances and Venting
EPA
Components Covered
Gas
X
Wood Pellet
Coal Electric Venting
Wood
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
1 Year
X
X
X
X
X
X
Igniters, electronic components,
and glass
X
X
X
X
X
X
2 years
X
X
X
Factory-installed blowers
Molded refractory panels
3 years
X
X
Firepots and burnpots
Castings and baffles
5 years 1 year
X
X
Manifold tubes,
HHT chimney and termination
7 years 3 years
X
X
10
1 year
years
X
X
X
Burners, logs and refractory
Firebox and heat exchanger
Limited
3 years
Lifetime
X
X
X
X
X
X
X
X
All replacement parts
beyond warranty period
90 Days
X
X
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 1 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CONDITIONS:
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
•
•
This warranty is only valid while the HHT appliance remains at the site of original installation.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
•
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
•
•
•
Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discolor-
ation of glass.
•
•
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-
plaints related to this noise are not covered by this warranty.
Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera-
tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
•
•
•
Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
•
•
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645C 12-29-10
Page 2 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
TL2.0 Woodburning stove
service & Maintenance Log
Date Of Service
Performed By
Description Of Service
37
Save These Instructions
3-90-08560
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
At Harman, we build each product to a standard, not a price.
This powerful heating appliance boasts uncompromising
attention to detail and helps preserve our planet by using
environmentally responsible fuels.
(Signature of Boxer)
Your premium quality hearth product designed and assembled
by the experienced and skilled members at Harman in Halifax,
PA, USA.
Proudly Printed On 100% Recycled Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
|