DIGITAL FISH SCALE
Model 94569
ASSEMBLY & OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS Manual.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
When unpacking your Digital Fish Scale, check to make sure that the product is intact and
undamaged. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS
at: 1-800-444-3353.
Operation
Your Digitial Fish Scale requires no assembly. It is important that you read the entire manual to
become familiar with the product BEFORE you use the Digital Fish Scale.
Do not bump or shock the Fish Scale when it is in operation or being transported. Rough
treatment may damage the highly sensitive mechanism.
Weighing the Fish
1.
2.
Insert a 9V battery (not included) into the Fish Scale-see Changing Battery section for
additional information.
Press the On/Off Button down for two to three seconds to turn the Scale “ON” and
activate the LED light. The LCD readout will display 0.00 and will flash when power is “ON”-
see Figure 1.
3.
The Fish Scale can be held by hand or hung from the loop at the top of the Scale. Place the
fish onto the Hook. Press the Hold Button down while the fish is being weighed; the Hold
Indicator light will go on-see Figure 2.
The Scale will register the weight of the fish in Lbs. Pressing the Hold Button down a
second time will bring the Scale back to zero.
Total Weight for More Than One Fish
1.
2.
Each time you weigh an individual fish, press down on the Memory Button. The memory
indicator light will go on-see Figure 2. Press the Total Button down to total the cumulative
weight of each fish that was entered into Memory. Up to ten fish can be entered into
Memory and added together to obtain a total weight.
To clear the Memory, press the Memory Button for two seconds. The LCD readout
will flash four times to verify that the memory has been cleared.
Figure 1
Figure 2
Memory
Battery
Compartment
On/Off Button
Total
Hold Button
SKU 94569
For technical questions please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing and Replacing the Battery
1.
2.
3.
Press down on the release tab on the back of the Fish Scale to open the Battery
Compartment.
Insert one 9V battery (not included) and line up polarity with the markings indicated in the
Battery Compartment.
When the Battery is running low, the LCD readout will show a picture of a battery. This
indicates that the battery needs replacing.
Figure 3
Backlight
Indicator
Low Battery
Memory
Indicator
Indicator
Hold
Indicator
Maintenance
1.
2.
Protect the Digital Fish Scale from rough use. It is susceptible to damage from being
dropped, struck, or other abuse.
Protect the Digital Fish Scale from exposure to water or corrosive materials. It should be
kept clean and dry. Occasional cleaning with a clean rag will extend its life and good
appearance.
3.
Lock it up and store in a dry location to inhibit rust. Keep out of the reach of children.
Troubleshooting
1.
2.
LCD flashes continously:
Battery charge is to low. Replace battery.
Display doesn’t change when Buttons are pushed: Circuit needs to be reset. Remove the
battery, wait 30 seconds, replace battery and turn the Fish Scale “ON”.
3.
LCD display does not show: Battery has poor connection or battery voltage is to low. Take
battery out and adjust connections. Replace the battery as necessary.
No replacement parts are available for this product.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL
ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BYTHE
BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 94569
For technical questions please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|