Dishwasher
DW12-PFE1
DW12-PFE1ME
Instructions for Use
0120501536
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Safety information
At time of delivery
If your family includes children
Check packaging and dishwasher immediately for signs of transport damage.
If the appliance is damaged, do not put it into use but contact your supplier
or customer service without delay.
The appliance is not intended for use by young children or infirm persons
without supervision.
Young children should be supervised to ensure that they do not play with
the appliance.
Please dispose of packaging materials properly.
Keep detergents out of the reach of children, who must also be kept away
from the dishwasher when it is open.
During installation
Site the dishwasher and connect it up in accordance with the installation
instructions.
If a fault occurs
If the appliance malfunctions, turn off water supply to the appliance and
disconnect the plug from the wall socket. Then, consult the section entitled,
"Fault finding" .If you cannot solve the problem, contact a service center.
Only specialised personnel are authorised to make repairs.
The dishwasher must not be connected to the electricity supply while instal-
lation is being carried out.
Ensure that the domestic wiring is properly earthed.
The mains electricity supply must conform to the details shown on the dish-
washer rating plate.
If the supply cord is damaged, it must be replaced by the manufacture, its
service agent of similarly qualified persons in order to avoid an electrical hazard.
To maintain the EFFICIENCY and SAFETY of this appliance,we recommend:
- call only the Service Centers authorised by the manufacturer.
- always use original Spare Parts.
Do not connect the dishwasher to the electricity supply via an extension
cable.
Built-under and built-in appliances should always be installed under a con-
tinuous work surface which is attached to the adjacent cupboards, in order
to ensure that the appliance is entirely stable.
After the appliance has been installed,the mains plug should still be easily
accessible.
When disposing of old appliances
Appliances which are no longer being used must be made inoperable by
cutting the power supply cord and removing the door lock.
Take the appliance to a designated waste disposal center.
Not on all models:
The plastic housing on the water inlet contains an electrically operated valve.
The connecting wires are inside the inlet hose.Do not cut through this hose
and do not immerse the plastic housing in water.
During installation, the power supply cord must not be bent or flattened.
Dangerous voltage
During normal use
The dishwasher must only be used by adults for the washing of household
dishes and cooking utensils.
This appliance cannot be installed outdoors, not even if the area in which it
is installed is covered by a roof; it is also very dangerous to leave it exposed
to the elements.
Warning
Safety of Children when disposing of your old
appliance.Some packaging materials can be dan-
gerous for children. There is a risk of suffocation,
keep packaging materials away from Children.
When disposing of old products remember to dis-
able the door locking system by breaking or re-
moving the door catch. and or hinges. This will
stop children from locking themselves inside the
product when playing. (Danger of suffocation).
Do not place any heavy objects or swing on the door when it is open. The
appliance could tip forward.
The water inside the dishwasher is not suitable for drinking.
Do not use solvents of any kind inside your dishwasher. They could cause
an explosion.
Open the door very carefully if the dishwasher is operating. There is a risk of
water squirting out.
Do not touch the heating element during or after a wash cycle.
Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet hands or feet;
- We discourage the use of extension cords and multiple sockets;
- If the appliance is not operating properly or maintenance must be
performed, disconnect the appliance from the power supply.
The door shall not be left in the open position since this could present a
tripping hazard.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Installation
Positioning the appliance
Attention:
The connecting piece for syphon trap (U-bend) must be
solidly fastened to the wall to prevent the drain hose from
moving and allowing water to spill outside the drain.
Positioning the appliance in the desired location. The back should rest against
the wall behind it, and the sides, along the adjacent cabinets or wall. The dish-
washer is equipped with water supply and drain hoses that can be positioned to
the right or the left to facilitate proper installation.
Electrical Connection
Levelling the appliance
After making sure that the voltage and frequency values for your home correspond
to those on the rating plate (located on the stainless steel inner door of the appliance)
and that the electrical system is correct for the maximum voltage on the rating
plate, insert the plug into an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
Once the appliance is positioned, adjust the feet (screwing them in or out) to
adjust the dishwasher, making it level. In any case, the appliance should not be
inclined more than 2˚. If the appliance is level, it will help ensure proper
performance.
If the electrical socket to which the appliance must be connected is not appro-
priate for the plug, replace the whole cable, rather than using adaptors or the
like as they could cause overheating and burns.
Cold water connection
Connect the water supply hose to a water outlet tap, making sure that it is
fastened tightly in place (see fig.A). Make sure the rubber washer is seated
firmly in the bottom of the connector.
Caution:
The dishwasher plug must be accessible even when the
appliance is installed as a built-in unit so that maintenance
can be done safely.
If the water pipes are new or have not been used for an extended period of time,
let the water run to make sure that the water is clear and free of impurities. If this
precaution is not taken, there is a risk that the water inletcan get blocked and
damage the appliance.
Electrical Connection (Uk Only)
For your safety please read the following information.
Warning: This appliance must be earthed.
The appliance must be connected to a 220-240 volts 50 cycle AC supply by
means of a three pin socket, suitably earthed and should be protected by a 13
amp fuse in the plug or a 15 amp fuse in the consumer unit.
fig.A
The appliance is supplied with a moulded 13 amp 3 pin mains plug fitted with a
13 amp fuse. Should the fuse require replacement, it must be replaced with a
fuse rated at 13 amp and approved to BS1362.
Warning
The appliance is to be connected to the water mains using
new hose-sets and that old hose-sets should not be reused.
The plug contains a removable fuse cover that must be refitted when the fuse is
replaced. In the event of the fuse cover being lost or damaged, the plug must
not be used until a replacement cover has been obtained.
Anti-Flooding protection (for some models)
Your dishwasher has an overfill protection device which could automatically shut
off the inlet valve and starts the drain pump if the water level in the unit is detected
to be above the normal level.
If the moulded mains plug is unsuitable for the socket outlet in your home or is
removed for any other reason, then the fuse should be removed and the cut off
plug disposed of safely to prevent the hazard of electric shock.
There is a danger of electric shock if the cut off plug is inserted into any 13 amp
socket outlet.
If this occurs, turn off the main water supply before calling for servicing. If there is
water in the base pan because of an overfill or small leak, the water should be
removed before restarting the dishwasher.
Drain hose connection
How to wire a 13 amp plug.
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it
run into the sink, making sure to avoid bending or crimping it. If necessary, fit a
syphon trap (U-bend) with a connecting piece for the drain hose (fig.B). The
free end of the hose must be at a height between 40 and 100 cm and must not
be immersed in water.
Important
The wires in the mains lead on this appliance are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue – Neutral
Brown – Live
As the colours may not correspond with the markings identifying the terminals
in your plug proceed as follows.
The green and yellow wire must be connected to the terminal in the plug which is
marked with the letter E or with the earth symbol
or coloured green and yellow.
The blue wire must be connected to the terminal marked N or coloured black.
The brown wire must be connected to the terminal marked L or coloured red.
Caution:
The dishwasher plug must be accessible even when the appliance is installed
fig.B
as a built-in unit so that maintence can be done safety.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Getting to know your dishwasher
Close-up view (control panel)
Dishwasher interior
a
c
i
j
e
f
k
b
d
g
h
A
C
Upper Rack
Lower Rack
a
b
g
h
i
Washing Filter
Detergent and Rinse Aid Dispenser
Water Inlet Hose
c Top Spray Arm
B
d Silverware Basket
e Bottom Spray Arm
f Salt Container Cap
j
Drain Hose
k
Power Supply Cord
Programme Indicator
ON-OFF Button
A
B
C
Programme Button
How to fill the salt
Adjusting salt consumption
Salt
The dishwasher is designed to allow for adjusting the amount of salt consumed
based on the hardness of the water used. This is intended to optimize the amount
of salt consumption keeping it to a minimum.
The hardness of the water varies from place to place. If hard water is used in
the dishwasher, deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt specifically
designed to eliminate lime and minerals from the water.
To adjust salt consumption, proceed as follows:
Unscrew the cap from the salt container;
Loading the salt into the container
There is a ring on the container with an arrow on it (see figure below ).
If necessary, rotate the ring in an anticlockwise direction from the "-" set-
ting towards the "+" sign, based on the hardness of the water being used.
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should be filled as
follows:
According to the “Water Hardness Tabel”, you can calculate the salt con-
sumption setting, then load the salt .
Remove the lower rack and then unscrew and remove the cap from the salt
container.
If you are filling the container for the
first time, fill it with 1/2 a litre of water.
Place the end of the funnel (supplied)
into the hole and fill with about 2 kg
It is recommended that adjustments be made in accordance with the following
table:
of salt. It is normal for a small amount
of water to come out of the salt container.
Carefully screw the cap back on. Do not
over tighten it.
Water Hardness
Salt
Autonomy
(cycles/2kg)
Selector
position
Clarke
consumption
(Grams/cycle)
ºdH
Level
mmol/l
degrees
1
2
3
4
0ꢀ14
MꢀNT
MꢀNIT
L
M
L
Important
NQꢀPS NUꢀQQ NIUꢀQIQ
PSꢀTN QRꢀUV QIRꢀUIV
=?J?
jba
?H?
OM
QM
SM
SM
QM
OR
To prevent the formation of rust, load the salt just
before beginning a wash cycle.
[TN
[UV
[UIV
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
How to fill rinse aid
Rinse aid
Loading the rinse aid
This product makes dishes sparkle and helps them to dry without spotting. The
Regardless of the type of detergent dispenser installed on your appliance, you
dispenser is located on the inside panel of the door .
must proceed as indicated below when loading the rinse aid.
When the low rinse aid indicator “ 1 ” is bright ,it means the rinse aid is low,you
must refill the rinse aid dispenser..
To open the dispenser, turn the "2" cap in an anti-clockwise direction and then
pour in the rinse aid, making sure not to overfill. The amount of rinse aid used
for each cycle can be regulated by turning the " 3" dose adjustor, located be-
neath the "2" cap, with a screwdriver. There are 6 different settings; the normal
dosage setting is 3.
1
Low
Important
2
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting
occurs, the dosage adjustor should be turned to a
higher setting.
3
Full
If the dishes have white streaks, turn the dosage ad-
justor to a lower setting.
How to fill the detergent dispenser
Detergent
Loading the detergent
To open the " 4 " cover on the dispenser, press the " 5 " button.
The detergent for the wash cycle should be poured into the " 6 " compartment.
The detergent for the pre-wash cycle should be poured into the “ 7 ”
compartment.
Detergent specifically intended for use with dishwashers must be used. The
dispenser must be refilled before the start of each wash cycle following the
instructions provided in the "Programme overview". The detergent dispenser is
located on the inside panel of the door.
After the detergent has been placed in the dispenser, close the cover and
press down until it clicks in place.
7
5
Notice:
4
To facilitate closing the cover, remove any ex-
cess detergent on the edges of the dispenser.
6
Not suitable for the dishwasher
Damage to glassware and other dishes
What you should not put into the dishwasher
Possible causes
Cutlery and tableware manufactured in whole or part from wood.They become
faded and unsightly in appearance.Furthermore,the adhesives that are used
are not suitable for the temperature that occur inside the dishwasher.Delicate
decorative glassware and vases,special antique or irreplaceable china. The deco-
rative patterns on such items will not be dishwasher-proof.
type of glass or manufacturing process
chemical composition of detergent
water temperature and duration of dishwasher programme.
Suggested remedy
Plastic objects that are not resistant to hot water, copper and pewter utensils
are also not suitable. Decorative patterns printed or painted onto the surface of
crockery, glasses, etc.,aluminium and silver items tend to become discoloured
or faded if washed in the diswasher. Some types of glass can become opaque
in appearance after they have been washed many times in a dishwasher. Highly
absorbent materials, such as sponges and towels,should never be placed in the
dishwasher.
Use glassware or porcelain dishes that have been marked ‘dishwasher-proof’
by the manufacture.Use a mild detergent that is described as ‘kind to dishes’.
If necessary, seek further information from detergent manufacturers.
Select a programme with a low temperature and a short duration as possible.
To prevent damage, take glass and cutlery out of the dishwasher as soon as
possible after the programme has ended.
Important
Our recommendation
Dishes or cutlery that have been soiled by tobacco
ash, wax, Iubricating grease or paint, should not
be put in the dishwasher.
In future, only purchase table or kitchenware that has been confirmed as being
dishwasher-proof.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Arranging crockery, glasses, etc. in the dishwasher
Before placing the dishes in the dishwasher, remove larger food particles to
How to use the upper rack
prevent the filter from becoming clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely hard to remove, we
recommend that they are soaked before washed. This will eliminate the need
for extra wash cycles.
The upper rack is designed to hold more delicate and lighter dishware, such as
glasses, cups and saucers, plates, small bowls and shallow pans (as long as
they are not too dirty).
Pull out the rack to load the dishwasher.
Position the dishes and cookware so that they do not get moved by the spray
of water.
How to use the lower rack
The upper rack can be adjusted for height by using the knobs located on both
sides of the rack itself (see fig.F).
We recommend that you place the most difficult to clean items on the bottom
rack: pots, pans, lids, serving dishes and bowls, as shown in the figure to the
right.
Adjust the upper basket by pulling the end stops (Fig.E) outwards and
remove the upper rack completely re-insert using the upper or lower
wheels.
It is preferable to place serving dishes and lids on the sides of the racks in order
to avoid blocking the rotation of the top spray arm.
Pots, serving bowls, etc. must always be placed face down(see fig.C) .
Deep pots should be slanted to allow the water to flow out.
The silverware basket can be doubled (see fig.D) so that only one section
may be used when the silverware load is light. This also makes space for
additional pots and pans and it can also be placed in the upper rack.
Silverware should be placed in the silverware basket with the handles at the
bottom; if the rack has side baskets, the spoons should be located individu-
ally into the appropriate slots. Especially long utensils should be placed in
the horizontal position at the front of the upper rack.
fig.F
fig.E
Shelf
ꢀ
ꢀ
Lean tall glasses and those with long stems against the shelf-not against other
items to be washed.
Place glasses, cups and small bowls on the additional cup rack. The additional
cup rack can be swivelled in or out as required(see fig.G).
ꢀ
Knife rack
fig.C
The knife rack clips onto the side of the top basket, giving you the freedom to
Normal daily load
ꢀ
wash your large sharp knives separately and out of harm’s way (see fig.H).
fig.D
Warning
knives and other utensils with sharp points must
be loaded in the basket with their points down
or placed in a horizontal position.
fig.G
fig.H
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Programme overview
Type of
crokery
Detergent
Energy
consu-
mption
in kWh
Water
consu-
mption
in litres
Condi-
tion of
food
Duration
in
Wash
progra-
mme
Type of
food
Rinse
Aid
Amount
of food
remains
e.g.china,
pots/pans,
cutiery,
glasses,
etc
Exten-
Pre-
Description of cycle
ded
minutes
remains
wash
Wash
remains
Pre-wash with hot water.
Extended wash at 70°C.
Rinses with cold water.
Rinse with hot water.
Drying.
Soups,
Non-
5g
5g
5g
25g
25g
25g
15g
18
16
16
9
112
102
162
31
1.62
1.24
1.05
0.40
0.02
casseroles,
sauces,
Intensive
Wash
delicate
stuck
a lot
on hard
potatoes,
pasts, rice,
eggs, roast
or fried food.
Pre-wash use cold water.
Extended wash at 55°C.
Rinse with cold water.
Rinse with hot water.
Drying.
Normal
Wash
Soups,
Pre-wash use cold water.
Extended wash at 50°C.
Rinse with cold water.
Rinse with hot water.
Drying.
potatoes,
loosely
a little
pasta, rice,
eggs, roast
or fried food.
attached
(G)
Light Wash
(EN50242)
Coffee,
cakes, milk,
sausage,
cold drinks,
salads
Short wash at 40°C.
Cold rinse.
Very
little
loosely
Mixed
attached
Rapid wash
Soak
Rinse off if the dishes have
been stacked for several days
in the dishwasher prior to
washing.
Short cold wash to pre-
vent food residue from
drying on the dishes .
3
12
* EN50242 test with rinse aid setting 5
Care and maintenance
Regular inspection and maintenance of your appliance helps to prevent prob-
lems from occurring.This saves time and aggravation.You should therefore care-
fully inspect the inside of your dishwasher from time to time.
Inspect the nozzles in the spray arms for blocked holes due to remnants of
food.
If necessary, pull the lower arm “ 11 ” upwards and lift it off.
Unscrew the upper spray arm “ 10 ”.
Overall condition of appliance
Clean both spray arms under running water.
Refit the spray arms. Ensure that the lower arm has locked into place and
the upper one is screwed tight.
Check that no grease or scale has accumulated on the inside of the
dishwasher.
If you see any deposits:
Clean the interior of the dishwasher thorughly with a detergent solution.
Filters
The filters “ 8”,“ 9” prevent larger particles of food in the water from reaching
the pump.These particles may occasionally block the filters.
When the appliance has finished washing, check the filters for particles of
food and, if required, clean.
8
9
After undoing the coarse micro-filter “ 8 ” , the filter unit “ 9” can be removed.
Remove any particles of food and rinse the filters under running water.
Insert the filter unit “ 9 ” and tighten the coarse micro-filter.
11
Spray arms
Lime and remnants of food in the washing water can block the nozzles in the
10
spray arms “ 10 ” and “ 11 ” and the arm mountings.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Washing dishes
End of programme
Programme selection
Six beeps will indicate that the wash cycle has finished and all the programme
The most appropriate programme can be identified by comparing the type of
crockery, cutlery, etc., as well as the amount and condition of food remains,
with the details contained in the wash cycle table.The corresponding programme
sequence, duration and consumption details are shown in the right half of the
overview. For example:
indicators light.
Switching the dishwasher OFF
Several minutes after the programme has ended:
Set main switch “A” to OFF.
Use the« normal»
programme for dishes and utensils which have plenty of
Open the door .
food remains stuck on hard.
Turn the water tap off. (Does not apply when Aquastop unit has been fitted)
Remove dishes, etc. when they have cooled down.
Savings
If only a small number of dishes have been loaded into the dishwasher,select-
ing a programme that operates at the next lowest temperature will usually be
sufficient.
Interrupping the programme
Open the door. Caution! There is a risk of water squirting out from inside the
appliance. Do not open the door fully until spray arm has stopped rotating.
When you open the door, the dishwasher will beep ten times every thirty
seconds.
Programme data
The stated programme data are based on standard operating conditions. The
If the appliance has already heated up or the hot water was switched ON and
then the appliance door opened, leave the door ajar for several minutes and
then close. Otherwise, the appliance door may open due to expansion.
values can vary considerably according to:
different amounts of dishes
temperature of mains water supply
Cancelling or modifying a cycle
pressure of mains water supply
A cycle that is underway can be modified if it has only been running for a
short time. Otherwise, the detergent may have already been used, and the
appliance may have already drained the wash water. If this is the case, the
detergent dispenser must be refilled ( see the paragraph entitled, “ Loading
the detergent ”).
ambient temperature
fluctuations in mains voltage
machine-related factors (e.g. temperature, water volume,...)
Energy and water consumption is reduced by up to 1/4 when dishes are washed
in the upper basket only.The water consumption values are related to water
hardness level 1.
To modify a cycle that is already underway, press the button“ A ” , all of the
settings will be cancelled. To set a new cycle, follow the instructions con-
tained in the paragraph entitled “Switching the dishwasher ON”.
Switching the dishwasher ON
Turn on the tap.
Set ON-OFF button “ A ” to ON. All the programme indicators“C1,C2,C3,
C5,C6”light .
C1 C2 C3 C5 C6
Press programme button “B1-6”,programme indicator “ C1-6” blinks.
If the door is closed, after 5 seconds, the programme indicator “ C1” lights
steady and the dishwasher beeps once time, then the programme starts
automatically.
A
B1
How to keep your dishwasher in shape
Moving the Appliance
If the appliance must be moved, try to keep it in a vertical position. If absolutely
After Every Wash
After every wash, turn off the water supply (not necessary for models with
“Aquastop” ) the appliance and leave the door slightly ajar so that moisture and
odors are not trapped inside.
necessary, it can be positioned on its back.
Seals
One of the factors that cause odors to form in the dishwasher is food that re-
mains trapped in the seals. Periodic cleaning with a damp sponge will prevent
this from occurring.
Remove the plug
Before cleaning or performing maintenance, always remove the plug from the
socket. Do not run risks.
The door should not be left in the open position since this could present a
tripping hazard.
No solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not use solvents or
abrasive cleaning products. Rather, use only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use a cloth damp-
ened with water and a little white vinegar, or cleaning product made specifically
for dishwashers.
When You Go on Holiday
When you go on holiday, it is recommended that you run a wash cycle with the
dishwasher empty and then remove the plug from the socket, turn off the water
supply and leave the door of the appliance slightly ajar. This will help the seals
last longer and prevent odors from forming within the appliance.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Fault finding
Resolving minor problems yourself
Experience has shown that you can resolve most problems that rise during
normal daily usage yourself, without having to call out a service engineer.Not
only does this save costs,but it also means that the appliance is available for
use again that much sooner. The following list of common occurrences and
their remedies should help you identify the causes of most problems.
the problem.
the model type number (Mod...) And the serial number (S/N...), which are
indicated on the plate located on the side of the inner part of the door.
Lower spray arm rotates with difficulty
Spray arm is blocked by small items or food remains.
Problems...
Lid in detergent compartment cannot be closed
...when the appliance is switched on
Detergent compartment has been overfilled.
Appliance does not start up
Mechanism is clogged with remnants of detergent.
Fault with fuse in mains electricity supply.
Plug not inserted in wall socket.
Indicator lamps do not extinguish after washing has finished
Main switch is still set to ON.
Appliance door not closed properly.
Programme button has not been pressed.
Water tap not turned on.
Remnants of detergent stuck inside dispenser
Compartment was damp when it was filled up with detergent. Compartment
must be dry before detergent is added.
Blocked strainer in water intake hose.
- The strainer is situated in the Aquastop or supply-hose connection.
Water remains inside appliance after programme has ended
Blockage or kink in drainage hose.
Caution
Do not forget that repairs should only be carried
out by a qualified specialist. Improper repairs can
lead to considerable equipment damage as well
as danger to the user.
Pump is jammed.
Filters are blocked.
The programme is still running. Wait for the programme to end .
...during washing
...with the appliance itself
Error display on the time-remaining indicator
When all the programme indicators “ C” blink.
Unusual amount of foam is creased
Normal washing up liquid has been poured into the rinse-aid container.
Have you checked whether:
the door is closed properly.
Remove any spilled rinse aid with a cloth as it could otherwise lead to exces-
sive foaming during the next washing cycle.
C
Appliance stops suddenly while washing is taking place
Cut off electricity supply to appliance.
Water supply has been interrupted.
When the programme indicators “C1,C2,C3” blink.
Have you checked whether:
Knocking sound can be heared while washing is taking place
the water is turned on and the hose is connected properly;
the water supply to the house is on and has sufficient pressure;
the water supply hose is crimped or bent;
A spray arm is knocking against the dishes inside the appliance.
C1 C2 C3
the filter for the water supply hose is clogged.
the drain hose is too low.
Rattling sound can be heared while washing is taking place
Crockery has not been stacked properly inside the appliance.
Knocking sound coming from inlet valves
When the programme indicators “ C1,C3,C5” blink.
This is caused by the way the water pipes have been laid and it has no effect
upon the way the appliance functions. There is no remedy for this.
Have you checked whether:
C1
C3
C5
the drain hose is crimped or bent.
the drain hose is too high.
...with the dishes,cutlery, etc.
Remnants of food are stuck to the dishes, cutlery,etc.
Dishwasher was not loaded properly. Jets of water could not reach all parts
of the dishes, ect.
When the programme indicators “ C1,C2,C5” blink.
Have you checked whether:
Too many items in the rack.
C5
C1 C2
Items in the rack were touching each other.
Not enough detergent was added to dispenser.
Selected wash programme was not intensive enough.
Rotation of spray arm was obstructed by dishes, etc.
N ozzles in spray arm are blokcked by remnants of food.
Filters are blocked.
the drain hose is too low.
If you take all these checks and the dishwasher still does not func-
tion or your dishwasher has any other error display, you can power
the dishwasher OFF, and wait a few minutes. You can power the
dishwasher on, try it again , if the dishwasher still does not func-
tion and/or the problem persists, contact the nearest authorised
service center and provide them with the following information:
Filters have been incorrectly fitted.
Waste-water pump is jammed.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Plastic items are discoloured
Tea stains or traces of lipstick have not been completely removed
Not enough detergent was added to dispenser.
Detergent does not have a sufficient bleaching effect.
Washing temperature was set too low.
Detergent has insuffcient bleaching properties. Use a detergent containing a
chemical bleaching agent.
White stains are left on crockery, glasses have a milky appearance
Traces of rust on cutlery
Not enough detergent was added to dispenser compartment.
Amount of rinse-aid was set too low.
Cutlery is not sufficiently rustproof.
Salt content in washing water is too high.
- Lid on salt container is not screwed tight.
- Too much salt was spilt while filling container.
Although water is quite hard, no salt has been put in appliance.
Water softener was set too low.
Lid on salt container is not screwed tight.
Glasses become clouded and discoloured; coating cannot be wiped
off
If you used a phosphate-free detergent , try a detergent containing phos-
phates and compare results.
Unsuitable detergent was used.
Glasses are not dishwasher-proof.
Dishes,cultlery,etc.have not been dried
Selected programme did not include drying function.
Amount of rinse-aid was set too low.
Smears left behind on glasses and cutlery; glasses have acquired
a metallic appearance
Items were removed from dishwasher too soon.
Glasses have a dull appearance
Amount of rinse-aid set too high.
Amount of rinse-aid was set too low.
Important information
Notes on waste disposal
Information on loading the dish washer
Old appliances still have some residual value. An environment-friendly method
of disposal will ensure that valuable raw materials can be recovered and used
again.
Below is an example on how to load this dish washer Figs 1-2.
When an appliance has reached the end of its working life,unplug it from the
mains.Cut through the mains cable and dispose of it together with the plug.
Destroy the door locking mechanism. This will ensure that children at play can-
not become locked inside and are not exposed to the risk of suffocation.
Your new appliance was protected by suitable packaging while it was on its
way to you. All materials used for this purpose are environment-friendly and can
be recycled. Please make a contribution to protecting the environment by dis-
posing of the packaging appropriately.
Fig.2
Fig.1
Do not allow children to play with any parts of the packaging. There is a risk of
suffocation by the cardboard boxes and the plastic wrapping.
Up-to -date information concerning options for disposal can obtained from your
retailer or local municipal administration.
General information
Measures must be taken to ensure that built-under and built-in units that
are subsequently re-sited as free-standing appliances cannot topple over.
This can be achieved by bolting the dishwasher to the wall or fitting it under
a continuous work surface which is screwed to the adjacent cupboards.
For Switzerland only:
There are no restrictions on installing the appliance between wooden or
plastic walls as part of a fitted kitchen. If the appliance is not plugged into a
wall socket, it must be connected to the mains via a separator for all poles
within the domestic wiring system. This device must have a gap of at least
3mm between open contacts, in order to conform with relevant safety
regulations.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Technical data
Mains water pressure
Power voltage
0.03-0.6MPa
60 cm
60 cm
Width
Depth
Height
220-240V~ 50Hz
10A
Maximum current intensity
Total absorbed power
85 cm
Capacity
12 standard place settings
1950W
A: Wiring box
F: Softener valve
G: Overflow switch
H: Inlet valve
K: Heater
L: Relay
M:T 50oC
B: Door switch
C: Water level switch
D: Drain pump motor
E: Dispenser
I: Washing pump motor
J: Temperature limiter
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|