OWNER’S MANUAL
Bin Level
Automatic Control Grain Spreaders
Models 918 & 936
PNEG-1137
Date: 08-10-07
PNEG-1137
Download from Www.Somanuals.com. All Manuals Search And Download.
Bin Level
SAFETY GUIDELINES
This manual contains information that is important for you, the owner/operator, to know and
understand. This information relates to protecting personal safety and preventing
equipment problems. It is the responsibility of the owner/operator to inform anyone
operating or working in the area of this equipment of these safety guidlines.To help you
recognize this information, we use the symbols that are defined below.
Please read the manual and pay attention to these sections. Failure to read this manual
and it’s safety instructions is a misuse of the equipment and may lead to serious injury or death.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a potentially
hazardous situation which, if not avoided, may result in property
damage.
NOTE indicates information about the equipment that you should
pay special attention to.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Bin Level
1. Disconnect all power before servicing or adjusting. Have bin properly grounded.
NOTE: With power on, the unit will start unexpectedly if the mercury switch is activated
by jerking, shaking or jarring.
2. Do not enter a bin without proper eye protection while the unit is operating.
3. Do not attempt to service or adjust the unit from a ladder unless the ladder is secured to
another piece of equipment or to the bin. The grain spreader can swing and will not support a
ladder. Be sure electric power IS DISCONNECTED.
4. Power cords, plug and receptacles should be grounded type to prevent personal injury.
5. All wiring should be done according to the National Electric Code and by a qualified electrician.
6. Read and understand the operator’s manual.
****WARNING****
FAILURE TO FOLLOW THESE INSTRUCTIONS MAYRESULT IN PERSONALINJURYOR PROPERTYDAMAGE.
INSTALLATION
FIG. 1
FIG. 5
FIG. 2
FIG. 3
FIG. 4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Bin Level
Installation and Operation
INSTALLATION
Figure 1: 918 and 936 Bin Level - Hanger Hooks and Chains
Double chains are attached to the hopper in three places. One chain from each of the three attachment points is
hooked into a hanger hook to form a “V”. This is necessary to keep the spreader from swinging around the fill-
hole each time the spreader is started.
The Bin Level hanging height can change the spreading pattern. On steep-roofed bins, hanging the Bin Level
lower in the bin will be beneficial for a more level grain spread.
All Bin Levels should be installed so that, during operation, grain from legs or augers is not directly hitting the
mercury switch control plate.
INSTALL THE BIN LEVEL SPREADER AS LEVEL AS POSSIBLE
ADJUSTMENT & OPERATION
Figure 2: Adjusting Flow Rate
The two wing nuts inside of the top of the hopper regulate the volume of grain the Bin Level will spread by
adjusting the gap between the lower end of the hopper and the spreader pan. This adjustment should be
made so the incoming grain operates the switch, turning the motor on at least three times per minute and
not more than six times per minute. If the Bin Level is adjusted to start and stop less than three times per
minute, level spread cannot be achieved. If adjusted to start and stop more than six times per minute, motor
damage can result. Adjusting the Bin Level to operate within the recommended “stop” and “start” pattern is a
must to achieve a level spread.
Figure 3: Outside Ring Adjustment
The outside ring of the Bin Level grain spreader is designed so it can be raised or lowered depending upon the
amount of grain being put through the spreader and the width of spread needed. Because of this feature the
grain is showered up and out into the bin which allows an even spread, regardless of the corn depth in the bin.
To attain this showering action, the outside ring has to be kept higher than the bottom of the hopper cone.
Under normal conditions, the outside ring should be from 1/2” to 3/4” higher than the bottom of the Bin Level
cone or fill hopper.
Raise the ring to throw grain farther to the outside. Lower the ring to decrease spread width.
Figure 4: Side Gate Adjustments
A slide gate is provided in the spreader pan to keep the center level with the remainder of the bin. Adjustment
of the slide gate will vary, depending upon volume and number of start-stops per minute at which the Bin Level
is set.
CHECK PERIODICALLY FOR CLOGGING WITH TRASH
Figure 5: Mercury Switch Control
This is the heart of the Bin Level grain spreader. By use of the mercury switch, the spreader is always operat-
ing under full-load capacity so a very even spread is obtained. IMPORTANT: For proper operation, the
mercury switch plate has to be kept from becoming bent or from having other physical damage, and must
work freely at all times.
Do not direct flow of grain onto the mercury switch plate. Mercury switch and/or motor failure will result!
SPREADING CAPACITIES
Various Weights of Grain in Relation to Distance Spread
MODEL
HP
BIN SIZE
LIGHT GRAIN
2500 BPH 3500 BPH 3500 BPH
HEAVY GRAIN
918
936
1/3
1/2
18'-30'
31'-36'
18'-27'
28'-33'
18'-24'
25'-30'
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
Bin Level
BIN LEVEL GRAIN SPREADER
PARTS DRAWING
FOR MODELS 918 & 936
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Bin Level
Parts List
Bin Level Grain Spreader
Parts List
918
936
Ref.
No.
Part
No.
Required
Ref.
No.
Part
Number
No.
Required
Number
301A0102
301A0108
301A0110
301A0111
301A0122
301B0202
301B0208
301B0220
301B0221
Description
Description
1
2
1
1
1
1
1
2
3
3
3
1
1
1
2
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
4
6
1
10
2
2
3
3
2
4
2
6
4
2
1
3
2
1
1
4
10
2
8
12
1
1
Handle Nut
Ring - Outside Pan
Gate - Slide
Pan - Spreader, 18" O.D.
Wheel - Rubber Drive, 2-3/4"
Shield - Pow er Cord
Counter Balance Wt.-Sw itch Plate
Bracket - Hanger
1
2
3
4
5
6
7
8
9
301A0102
302A0309
301A0110
302A0307
302A0313
301B0202
301B0208
301B0220
301B0221
2
1
1
1
1
1
2
3
3
3
1
1
1
2
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
4
6
1
10
2
2
3
3
2
4
2
6
4
2
1
3
2
1
1
4
10
2
8
12
1
1
3
Handle Nut
Ring - Outside Pan
Gate - Slide
Pan - Spreader, 20" O.D.
Wheel - Rubber Drive, 3-1/4"
Shield - Pow er Cord
Counter Balance Wt.-Sw itch Plate
Bracket - Hanger
2
3
4
5
6
7
8
9
U-Bolt - Hanger
U-Bolt - Hanger
10 301B0222
11 301B0236
12 301B0237
13 301B0239
14 301B0244
15 301B0245
16 302A0303
17 302A0304
18 302A0311P
19 302B0406
20 302B0408
21 301N0014
24 PT0109
25 PT0215
26 PT0401
28 1782
29 1EL0553
30 1EL0802
31 2EL0601-R
32 3EL5055
33 S-4189
34 S-4310
35 S-4663
36 S-396
Chain - Hanger, 54" Length
Cover - Sw itch Housing
Hinge Pin - Mercury Sw itch Plate
Mercury Sw itch Plate
Spacer Tube
Hopper - Hex
Shaft - Hopper Center
Plate - Motor Mount
Spring - Motor Mount, Torsion
Support - Hopper Center - (Upper)
Support - Hopper Center - (Low er)
Cord - Pow er
Bearing, (Complete) 1" (Precision)
Bearing, 1" w /Locking Collar
Collar - Eccentric Lock, 1"
Connector, 3/8"
Wire Tw ist Connector, Gray
Mercury Sw itch Clip
Mercury Sw itch, 6 Degree
Motor, 1/3 HP, T.E.N.V. Electric
Wing Nut, 1/4"
Hex Lock Nut, 1/4"
Hex Lock Nut, 3/8"
Hex Nut, 5/16"
Hex Nut, 3/8"
Hex Machine Screw Nut, #4-40
Hex Flange Lock Nut, 5/16"
Hex Flange Lock Nut, 7/16"
Set Screw - Skt. Hd. 1/4"x1/4"
Carriage Bolt, 1/4"x3/4"
Machine Screw -Rd. Hd.#4-40x5/8"
Hex Bolt, 1/4"x1/2"
10 301B0427
11 301B0236
12 301B0237
13 301B0239
14 301B0244
15 301B0245
16 302A0303
17 302A0304
18 302A0311P
19 302B0439
20 302B0408
21 301N0014
24 PT0111
25 PT0215
26 PT0401
28 1782
29 1EL0553
30 1EL0802
31 2EL0601-R
32 3EL5062
33 S-4198
34 S-4310
35 S-4663
36 S-396
Chain - Hanger, 72" Length
Cover - Sw itch Housing
Hinge Pin - Mercury Sw itch Plate
Mercury Sw itch Plate
Spacer Tube
Hopper - Hex
Shaft - Hopper Center
Plate - Motor Mount
Spring - Motor Mount, Torsion
Support - Hopper Center - (Upper)
Support - Hopper Center - (Low er)
Cord - Pow er
Bearing, (Complete) 1" (Precision)
Bearing, 1" w /Locking Collar
Collar - Eccentric Lock, 1"
Connector, 3/8"
Wire Tw ist Connector, Gray
Mercury Sw itch Clip
Mercury Sw itch, 6 Degree
Motor, 1/2 HP, T.E.N.V. Electric
Wing Nut, 1/4"
Hex Lock Nut, 1/4"
Hex Lock Nut, 3/8"
Hex Nut, 5/16"
Hex Nut, 3/8"
37 S-456
37 S-456
38 S-7054
39 1FH0983
40 1FH0985
41 S-7186
42 S-6369
43 2FH0687
44 S-1101
45 S-8072
46 S-7521
47 S-7744
48 2FH0990
49 3FH0530
50 3FH0567
51 S-9159
52 S-2041
53 S-1147
54 S-1054
55 S-1430
56 S-1937
57 3FH0999
58 S-6371
59
38 S-7054
39 1FH0983
40 1FH0985
41 S-7186
42 S-6369
43 2FH0687
44 S-1101
45 S-8072
46 S-7521
47 S-7744
48 2FH0990
49 3FH0530
50 3FH0567
51 S-9159
52 S-2041
53 S-1147
54 S-1054
55 S-1430
56 S-1937
57 3FH0999
58 3FH1015
59 3FH0830
Hex Machine Screw Nut, #4-40
Hex Flange Lock Nut, 5/16"
Hex Flange Lock Nut, 7/16"
Set Screw - Skt. Hd. 1/4"x1/4"
Carriage Bolt, 1/4"x3/4"
Machine Screw-Rd. Hd.#4-40x5/8"
Hex Bolt, 1/4"x1/2"
Hex Bolt, 5/16"x3/4"
Hex Bolt, 3/8"x 1 1/2"
Hex Bolt, 3/8" x 5-1/2"
Hex Flange Wiz Lk.Scr., 5/16"x1"
Pop Rivet-3/16" Aluminum
Snap Ring 1"
Hex Bolt, 5/16"x3/4"
Hex Bolt, 3/8"x 1 1/2"
Hex Bolt, 3/8" x 5-1/2"
Hex Flange Wiz Lk.Scr., 5/16"x1"
Pop Rivet-3/16" Aluminum
Snap Ring 1"
Cotter Pin, 1/8"x3/4"
Lock Washer, 1/4"
Lock Washer, 5/16"
Lock Washer, 3/8"
Cotter Pin, 1/8"x3/4"
Lock Washer, 1/4"
Lock Washer, 5/16"
Lock Washer, 3/8"
Flat Washer, 1/4"
Flat Washer, 1/4"
Flat Washer, SAE, 5/16"
Key - Woodruff(Tab Type) 1/4" x1"
Key - Square, 1/8"x1"
Not used on 918 Bin Level
Flat Washer, SAE, 5/16"
Key - Woodruff(Tab Type) 1/4" x1"
Key - Square, 3/16"x1"
Machinery Bushing, 1"x1-1/2"x10GA
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
Bin Level
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Bin Level
TROUBLE SHOOTING
PROBLEM
CORRECTION
(a) Spreader is not hung level.
(b) Spreader not stopping & starting properly during filling. See Figure 2.
(c) Spreader running continuously.
Grain is high on
one side of bin.
(a) Slide Gate open too far.
(b) Spreader stopping too long, letting too much grain through slide gate.
See Figure 4.
Grain is high at the
center of bin.
(c) Outside ring set too low. See Figure 3.
(a) Slide Gate not open far enough.
(b) Spreader not stopping enough to let grain out through slide gate.
See Figures 2 and 4.
Grain is low at the
center of bin.
(c) Outside ring set too high. See Figure 3.
Caused by grain bouncing off bin wall excessively.
(a) Adjust outside ring. See Figure 3.
(b) Hook Spreader higher in the roof cone to increase grain bouncing off
underside of roof and then being deflected straight downward.
(c) Open slide gate more to help fill center.
Grain forms “doughnut”
a few feet from bin wall.
(d) Spreader model not correct for bin size.
(a) The Model 918 Bin Level will only spread over an entire bin width of up
to 30’ and the Model 936 up to 36’. If the bin is bigger, lower sides will
result because grain will not throw out far enough.
(b) Adjust outside ring up. See Figure 3.
Grain not getting all
the way to the wall.
(c) Bin Level hanging too high under bin roof.
(d) Rubber drive wheel badly worn.
Spreader swings exces-
sively
This condition is caused by improper hooking up of the suspension chains.
There should be the same number of links from spreader to hook with all six
strands of chain. This will also usually ensure level hanging of the Spreader.
Equal spacing of hanger brackets is important.
The hanger brackets should be on the outer fill-hole ring.
(a) Mercury switch plate may be frozen shut or plugged with foreign material.
(b) Rubber drive wheel may be slipping because of excessive moisture or
broken mounting plate spring.
Spreader does not run.
(c) Motor overload may have tripped. It will reset automatically after the motor
has cooled.
(d) Blown fuse or broken wire.
(e) Faulty mercury switch.
(f) Mercury switch plate bent out of shape.
(g) Grain extremely high moisture may not flow enough to operate the mercury
switch plate. Bending section of the plate holding the mercury switch up to
make it more sensitive may help.
(h) The motor will not start and will “chatter” if the voltage is too high.
(i) The motor will not start and will “hum” if the voltage is too low. See Table A
on Page 8 for the proper length and size of wiring to prevent excessive
voltage drop.
Motor slows down when loaded.
(a) Motor wired for the wrong direction. Pan should turn clockwise when
viewed from the top.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Bin Level
NOTES
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Bin Level
The GSI Group, Inc. Warranty
THE GSI GROUP, INC. (“GSI”) WARRANTS ALL PRODUCTS WHICH IT MANUFACTURES TO
BE FREE OF DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USAGE AND
CONDITIONS FOR A PERIOD OF 12 MONTHS AFTER RETAIL SALE TO THE ORIGINAL END
USER. THE PURCHASER’S SOLE REMEDY AND GSI’S ONLY OBLIGATION SHALL BE TO
REPAIR OR REPLACE, AT GSI’S OPTION AND EXPENSE, PRODUCTS THAT, IN GSI’S SOLE
JUDGMENT, CONTAIN A MATERIAL DEFECT DUE TO MATERIALS OR WORKMANSHIP.
ALL DELIVERY AND SHIPMENT CHARGES TO AND FROM GSI’S FACTORY WILL BE
PURCHASER’S RESPONSIBILITY. EXPENSES INCURRED BY OR ON BEHALF OF THE
PURCHASER WITHOUT PRIOR WRITTEN AUTHORIZATION FROM AN AUTHORIZED
EMPLOYEE OF GSI SHALL BE THE SOLE RESPONSIBILITY OF THE PURCHASER.
EXCEPT FOR THE LIMITED WARRANTY EXPRESSED ABOVE, GSI MAKES NO FURTHER
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR
USE IN CONNECTION WITH (I) PRODUCT MANUFACTURED OR SOLD BY GSI OR (ii) ANY
ADVICE, INSTRUCTION, RECOMMENDATION OR SUGGESTION PROVIDED BY AN AGENT,
REPRESENTATIVE OR EMPLOYEE OF GSI REGARDING OR RELATED TO THE
CONFIGURATION, INSTALLATION, LAYOUT, SUITABILITY FOR A PARTICULAR PURPOSE,
OR DESIGN OF SUCH PRODUCTS.
GSI SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOSS OF ANTICIPATED
PROFITS OR BENEFITS. PURCHASER’S SOLE AND EXCLUSIVE REMEDY IS AS SET FORTH
IN THE LIMITED WARRANTY EXPRESSED ABOVE, WHICH SHALL NOT EXCEED THE
AMOUNT PAID FOR THE PRODUCT PURCHASED. THIS WARRANTY IS NOT
TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER. GSI SHALL HAVE
NO OBLIGATION OR RESPONSIBILITY FOR ANY REPRESENTATIONS OR WARRANTIES
MADE BY OR ON BEHALF OF ANY DEALER, AGENT OR DISTRIBUTOR OF GSI.
GSI ASSUMES NO RESPONSIBILITY FOR CLAIMS RESULTING FROM ERECTION DEFECTS
OR UNAUTHORIZED MODIFICATIONS TO PRODUCTS WHICH IT MANUFACTURED.
MODIFICATIONS TO PRODUCTS NOT SPECIFICALLY DELINEATED IN THE MANUAL
ACCOMPANYING THE EQUIPMENT AT INITIAL SALE WILL NULLIFY THE PRODUCT
WARRANTY THAT MIGHT HAVE BEEN OTHERWISE AVAILABLE.
THE FOREGOING WARRANTY SHALL NOT EXTEND TO PRODUCTS OR PARTS WHICH
HAVE BEEN DAMAGED BY NEGLIGENT USE, MISUSE, ALTERATION OR ACCIDENT. THIS
WARRANTY EXTENDS SOLELY TO ONLY PRODUCTS MANUFACTURED BY GSI. THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR
IMPLIED. GSI RESERVES THE RIGHT TO MAKE DESIGN OR SPECIFICATION CHANGES AT
ANY TIME.
PRIOR TO INSTALLATION, PURCHASER HAS THE RESPONSIBILITY TO COMPLY WITH
ALL FEDERAL, STATE AND LOCAL CODES WHICH MAY APPLY TO THE LOCATION AND
INSTALLATION OF PRODUCTS MANUFACTURED OR SOLD BY GSI.
PHLEGAL: #1832020 v1 (139LG01!.DOC)
(revised December 2005)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
This Equipment shall be installed in accordance
with the current installation codes and applicable
regulations which should be carefully followed in
all cases. Authorities having jurisdiction should be
consulted before installation occurs.
For more information, contact the DMC Distribution Center closest to you.
Illiana Distribution Center
1004 E. Illinois St.
Clear Lake Distribution Center
5205 4thAve South
Assumption, Illinois 62510
Phone: 217-226-5100
Clear Lake, Iowa 50428
Phone: 641-357-3386
FAX:
217-226-5070
FAX:
641-357-1928
Copyright © 1999 by The GSI Group
Printed in the USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|