HP Virtual Connect Manager Command
Line Interface
User Guide
Version 1.20
Part Number 449298-001
September 2007 (First Edition)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction.................................................................................................................................. 5
Properties....................................................................................................................................... 7
Remote access to the Virtual Connect Manager............................................................................................. 8
Managed elements.................................................................................................................................... 9
interconnect.................................................................................................................................. 19
mac-cache.................................................................................................................................... 22
profile.......................................................................................................................................... 24
uplinkport..................................................................................................................................... 29
user............................................................................................................................................. 32
version......................................................................................................................................... 34
Help subsystem....................................................................................................................................... 34
Basic configuration.................................................................................................................................. 40
Logging in to the CLI...................................................................................................................... 40
Contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Fibre Channel setup....................................................................................................................... 46
Server Profile setup........................................................................................................................ 47
HP contact information............................................................................................................................. 53
Contents
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Virtual Connect overview
Virtual Connect is a set of interconnect modules and embedded software for HP BladeSystem c-Class
enclosures that simplifies the setup and administration of server connections. HP Virtual Connect includes
the HP 1/10Gb Virtual Connect Ethernet Module for c-Class BladeSystem, the HP 4Gb Virtual Connect
Fibre Channel Module for c-Class BladeSystem, and the HP Virtual Connect Manager.
Virtual Connect implements server edge virtualization so that server administrators can upgrade, replace,
or move server blades within their enclosures without changes being visible to the external LAN and SAN
environments.
The Virtual Connect Manager is embedded on the HP 1/10Gb Virtual Connect Ethernet Module for c-
Class BladeSystem and is accessed by users through web links provided by the Onboard Administrator or
through direct connection to the embedded web server.
The HP 1/10Gb VC-Enet Module supports the HP BladeSystem c7000 Enclosure, HP BladeSystem c3000
Enclosure, and all the server blades and networks contained within the enclosure and enables connection
to all brands of data center Ethernet switches.
The HP 4Gb VC-FC Module enables connection of the enclosure to Brocade, Cisco, McData, or Qlogic
data center Fibre Channel switches, but does not appear as a switch to the Fibre Channel fabric.
A Virtual Connect domain currently includes a single HP c-Class BladeSystem enclosure for a total of 16
servers. Within the domain, any server blade can access any LAN or SAN connected to a VC module,
and a server blade can be used as a spare for any server blade within the same enclosure.
By stacking (cabling) the Ethernet modules within the domain, every server blade in the domain can be
configured to access any external network connection. Fibre Channel modules within different I/O bays
are each connected directly to the same set of FC SAN(s). With this configuration, the Virtual Connect
Manager can deploy and migrate a server blade profile to any server in the Virtual Connect domain
without the need to change external LAN or SAN configurations.
Command line overview
The CLI can be used as an alternative method for managing the Virtual Connect Manager. Using the CLI
can be useful in the following scenarios:
•
HP Management Applications (for example: Systems Insight Manager or Insight Control tools) can
query the Virtual Connect Manager for information these tools need to present a complete
management view of HP BladeSystem enclosures and the devices contained within. This interface is
also used by the Management tools to execute provisioning and configuration tasks to devices within
the enclosure.
•
Users can develop tools that utilize Virtual Connect Manager functions for data collection and for
executing provisioning and configuration tasks.
Introduction
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
When no browser is available or you prefer to use a command line interface, you can access
management data and perform configuration tasks.
Command line syntax
CLI input is case-insensitive except when otherwise noted. The general CLI syntax format is as follows:
<subcommand> <managed element> <parameters> [<options>] [<properties>]
Item
Description
subcommand
managed element
parameters
Operation performed on a managed element
Management entity being operated on
Command extensions for a particular management operation
options
Attributes used to customize or control command execution behavior such as output
format, quiet-mode, and others
properties
One or more name or value pairs that are accessories to the command operation,
mainly for set and add operations
Example: ->add user mark password=asdf89g fullname="Mark Smith" enabled=true
In the above example, add is the subcommand, useris the managed element, markis a required
parameter for the operation, passwordis a required property, and fullnameand enabledare
optional properties.
Depending on the specific command being executed, certain parameters or properties might be required.
For example, when adding a new user, both a parameter representing the user name, as well as a
password (in the form of a property) are required to be specified. All other user properties are optional at
the time the user is added. In general, the properties are in the format name=value, and more than one
property is separated by a space.
Parameters
Parameters are command extensions that provide extra information needed for the execution of a
particular command. Whether or not a parameter is required depends on the specific command being
executed. For example, the show usercommand has an optional parameter, which represents the user
name if the user instance is being managed. If show useris entered, then a summary listing of all users
is shown. However, if the optional parameter (user name) is provided, only a single user instance is
displayed, for example, show user paul.
Some commands require that a parameter be specified, for example, the add usercommand. The
required parameter is the user name (add user jake), and if the username is not provided, an error
message displays indicating that a required parameter is missing.
Options
Options enable users to control certain behavior characteristics available during the command execution.
Some examples of options include controlling output format and specifying a quietmode for
suppressing interactive prompts that would normally require input from the user.
Options are distinguished from other command line elements by using a hyphen (-) in front of the option.
Option arguments are required or optional depending on the option being specified. For example, the -
Introduction
6
Download from Www.Somanuals.com. All Manuals Search And Download.
outputoption requires an argument, which is a list of one or more output format attributes. However,
the -quietoption does not require any arguments to be specified.
The general format of a CLI option is as follows:
-<option>[=argument1>,<argument2>, . . .]
Example: ->show user suzi -output=script1
In the example, -outputis the option, and script1is an option argument.
Properties
Properties are specific configuration attributes of a managed element. Properties are commonly used
during setoperations or addoperations where a managed element is being modified or created. In
some limited circumstances, properties might also be used as a part of a showor other command.
IMPORTANT: If a property value contains embedded spaces, then the entire property value
must be contained within single or double quotes. Likewise, if a double quote is part of a
property value, it should be contained within single quotes, and if a single quote is part of a
property value, it should be contained within double quotes.
CLI command execution modes
The Virtual Connect Manager CLI provides two different methods for executing commands: interactive
shell mode and non-interactive mode.
Interactive Shell Mode
This mode is used to invoke CLI command operations using the dedicated management shell. The shell is
provided after the user logs in with valid credentials, and only accepts known VCM CLI commands as
input. Users can quit the shell by using the exitcommand. An example of logging into the interactive
management shell is provided below. In the example, the primary VCM is located at IP address
192.168.0.120.
>ssh 192.168.0.120
login as: michael
password: ***********
--------------------------------------------------------------------
HP Virtual Connect Management CLI v1.20
(C) Copyright 2006-2007 Hewlett-Packard Development Company, L.P.
All Rights Reserved
--------------------------------------------------------------------
GETTING STARTED:
help
exit
: displays a list of available subcommands
: quits the command shell
<subcommand> ? : displays a list of managed elements for a subcommand
<subcommand> <managed element> ? : displays detailed help for a command
Introduction
7
Download from Www.Somanuals.com. All Manuals Search And Download.
->
Non-Interactive Mode
In some cases, users might want to write automated scripts that execute a single command at a time.
These scripts can be used to batch several commands in a single script file from the SSH client. An
example of how to use the non-interactive mode for CLI command execution is provided below. In the
example, the primary VCM is located at IP address 192.168.0.120.
IMPORTANT: To suppress prompting for a password during login, you must first setup the SSH
encryption keys using the VCM Web GUI, and configure your SSH client properly with the
keys. For additional information on configuring the SSH keys, see the HP Virtual Connect for c-
Class BladeSystem User Guide.
->ssh [email protected] show enclosure
<command output displayed to console>
Remote access to the Virtual Connect Manager
The Virtual Connect Manager CLI can be accessed remotely through any SSH session:
1.
2.
Start an SSH session to the Virtual Connect Manager using any SSH client application.
When prompted, type the assigned IP address or DNS name of the Virtual Connect Manager, and
then press Enter.
3.
4.
5.
6.
Type a valid user name, and then press Enter.
Type a valid password, and then press Enter. The CLI command prompt displays.
Enter commands for the Virtual Connect Manager.
To terminate the remote access SSH session, close the communication software or enter exit at the
CLI command prompt.
Introduction
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Command line
Subcommands
Command
Description
add
Add a new object to the domain or to another object
Assign a server profile to a server bay
assign
delete
exit
Delete the Virtual Connect domain configuration
Exit the Virtual Connect Manager command-line shell
Display help for a command or object
help
import
poweroff
poweron
reboot
remove
reset
Import an enclosure into the domain
Power off one or more servers
Power on one or more servers
Reboot one or more servers
Remove or delete an existing object (for example, users or profiles)
Reset one or more servers or other objects
Modify one or more configuration properties of an object
Display properties or information about an object
Unassign a server profile from a device bay
Update firmware on one or more interconnect modules
set
show
unassign
update
Managed elements
Managed element
Description
Display general enclosure device bay settings and information
Manage general Virtual Connect domain settings and
information
Manage general enclosure settings and information
Manage Ethernet network connections
Manage external settings and information
Manage FC SAN fabrics
Manage Fibre Channel SAN fabric connections
Manage interconnect module firmware
Ethernet IGMP Snooping settings
Manage I/O interconnect modules
Manage LDAP configuration settings
Command line
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Managed element
Description
Manage LDAP group configuration settings
Manage Ethernet MAC cache failover settings
Manage Virtual Connect Ethernet networks
Manage VC server profiles
Manage server blades in the enclosure device bays
Display stacking link information and status
Display overall domain status information
Display Virtual Connect Manager system event log
Manage interconnect module uplink ports
Manage shared uplink port sets
Manage local domain user configurations
Reset the Virtual Connect Manager that manages the domain
Display CLI version information
The following sections provide detailed information on how the subcommands are used with each
managed element.
To display command help, type a command followed by ?or -help. For additional information on the
devicebay
Manage general enclosure device bay settings and information.
Supported actions: help, show
Item
Description
show devicebay
Display all device bays in the domain
show devicebay [<DeviceBayID>|*]
Syntax
Parameters:
DeviceBayID
The reference ID of a device bay in the domain
The format of the device bay name is <EnclosureID:DeviceBay>
When Enclosure ID is not specified, it defaults to the local enclosure
Examples:
->show devicebay
Displays a summary listing of all device bays
->show devicebay *
Displays detailed information for all device bays
->show devicebay enc0:2
Displays detailed information for a specific device bay of a specific enclosure
domain
Manage general Virtual Connect domain settings and information.
Command line 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported actions: delete, help, set, show
Item
Description
delete domain
Delete the existing Virtual Connect domain configuration.
Deleting the domain removes the entire Virtual Connect domain configuration
and resets it back to the original defaults. After the domain has been deleted,
you are logged out and the Virtual Connect Manager resets.
delete domain [-quiet]
Syntax
Examples:
->delete domain
Deletes the Virtual Connect domain configuration and prompts for user
confirmation
->delete domain -quiet
Deletes the Virtual Connect domain quietly without prompting for user
confirmation (primarily used in automated scripting scenarios)
Item
Description
set domain
Modify domain configuration properties
set domain [Name=<NewName>] [DomainIp=<Enabled|Disabled>]
[IpAddress=<IPAddress>] [SubnetMask=<mask>]
[Gateway=<Gateway>] [MacType=<VC-Defined|Factory-Default|
User-Defined>] [MacPool=<1-64>] [MacStart=<address>]
[MacEnd=<address>] [WwnType=< VC-Defined|Factory-Default>]
[WwnPool=<1-64>]
Syntax
Properties:
Name
The new name of the domain. Valid characters include alphanumeric, "_", and
".". The maximum length of the name is 64 characters.
DomainIP
Enables or disables the Virtual Connect domain IP address. If enabled, then a
valid IP address subnet mask must be configured. If disabled, then DHCP is used
to obtain a valid IP address.
Enabling domain IP address configuration, or changing the domain IP address
can cause a temporary loss of connectivity to the Virtual Connect Manager. Use
caution when changing these settings.
IpAddress
SubnetMask
Gateway
A valid IP address to use for the domain IP address configuration
A valid subnet mask for the domain IP address configuration
A valid gateway address for the domain IP address configuration
MacType
The type of MAC address source to use for assignment. Valid values include VC-
Defined, Factory-Default, and User-Defined
MacPool
The pre-defined MAC pool to use for address assignment. Valid values include
integers 1-64. This property is only valid if the MacType is set to "VC-Defined". If
not specified, the default pool ID is 1.
MacStart
MacEnd
The starting MAC address in a custom user-defined range. This property is only
valid if the MacType is set to "User-Defined".
The ending MAC address in a custom user-defined range. This property is only
valid if the MacType is set to "User-Defined".
WwnType
The type of WWN address source to use for assignment. Valid values include
VC-Defined and Factory-Default.
Command line 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
WwnPool
The pre-defined WWN pool to use for address assignment. Valid values include
integers 1-64. This property is only valid if the WwnType is set to "VC-Defined".
If not specified, the default pool ID is 1.
Examples:
->set domain Name=MyNewDomainName
Changes the name of the Virtual Connect domain
->set domain DomainIp=Enabled
Enables the domain IP address
->set domain DomainIp=Enabled IpAddress=192.168.0.120
SubnetMask=255.255.255.0 Gateway=192.168.0.1
Configures the domain IP address and enables it
->set domain DomainIp=Disabled
Disables the domain IP address and uses DHCP instead
->set domain MacType=VC-Defined MacPool=10
Sets the MAC address source to VC-Defined with a pre-defined range
->set domain MacType=Factory-Default
Set the MAC address source to use factory default MAC addresses
->set domain MacType=User-Defined MacStart=00-17-A4-77-00-
00 MacEnd=00-17-A4-77-00-FF
Sets the MAC address source to a custom, user-defined address range
->set domain WwnType=VC-Defined WwnPool=5
Sets the WWN address source to VC-Defined with a pre-defined range
->set domain WwnType=Factory-Default
Sets the WWN address source to use factory default WWN addresses
Item
Description
show domain
Display general Virtual Connect domain information, such as the Virtual Connect
domain name and the VCM domain IP address settings
show domain [addressPool]
Syntax
Examples:
->show domain
Displays domain information
->show domain addressPool
Displays the VC defined address pools for the domain
enclosure
Manage general enclosure settings and information.
Supported actions: help, import, show
Item
Description
import enclosure
Import an enclosure into the domain
Command line 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
import enclosure UserName=<username> Password=<password>
Syntax
The password field is optional on the command line. If not specified on the
command line, the user is prompted for the same interactively.
Properties:
UserName
A valid user name of the Onboard Administrator user
A valid password of the Onboard Administrator user
Password
->import enclosure UserName=Administrator
Password=fgg7h*1
Example
Imports the local enclosure
Item
Description
show enclosure
Display all enclosures in the domain
show enclosure [<EnclosureID>|*]
Syntax
Parameters:
EnclosureID
The ID of an enclosure in the domain
Examples:
->show enclosure
Displays a summary listing of all enclosures
->show enclosure *
Displays detailed information for all enclosures
->show enclosure enc0
Displays detailed information for a specific enclosure
enet-connection
Manage Ethernet network connections.
Supported actions: add, help, remove, set
Item
Description
add enet-connection
Add a new Ethernet network connection to an existing server profile
add enet-connection <ProfileName>
[Network=<NetworkName>]
Syntax
[PXE=<enabled|disabled|UseBios>] [AddressType=<Vc-
Defined|Factory-Default|User-Defined>]
[EthernetMAC=<MAC Address> iScsiMAC=<MAC Address>]
Parameters:
ProfileName
The name of an existing profile to which the new connection is added.
(required)
Properties:
Network
The name of an existing network to associate with the connection. If the
network name is not specified, or is set to "unassigned," then the
network remains unassigned. (optional)
Command line 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
PXE
Enables or disabled PXE on the network connection. Valid values are
enabled, disabled, and UseBios. If this value is not specified, the default
is "UseBios."
Only one connection can have PXE enabled per profile.
AddressType
The source of MAC address assignments to be used during the creation
of the new connection. If not specified, the default is the domain default.
If "User-Defined" is specified, then both an Ethernet MAC Address and
iSCSI MAC Address must also be specified. Valid values include Vc-
Defined, Factory-Default, and User-Defined.
EthernetMAC
iScsiMAC
The user-defined Ethernet MAC address to use for the connection. This
property is required if the AddressType specified is "User-Defined."
The user-defined iSCSI MAC address to use for the connection. This
property is required if the AddressType specified is "User-Defined."
Examples:
->add enet-connection MyNewProfile
Network=SomeNetwork
Adds a new Ethernet network connection to a profile
->add enet-connection MyNewProfile
Network=SomeNetwork2 PXE=enabled
Adds a new Ethernet network connection and enables PXE
->add enet-connection MyNewProfile
Adds a new Ethernet network connection and leaves the network
unassigned
->add enet-connection MyNewProfile
AddressType=Factory-Default
Adds a new Ethernet network connection and uses factory default
addresses
->add enet-connection MyNewProfile AddressType=Vc-
Defined
Adds a new Ethernet network connection using VC-defined addresses
->add enet-connection MyNewProfile AddressType=User-
Defined EthernetMAC=00-17-A4-77-00-00 iScsiMAC=00-
17-A4-77-00-01
Adds a new Ethernet network connection and provides user-defined
MAC addresses
Item
Description
set enet-connection
Modify an existing server profile connection
set enet-connection <ProfileName> <Port>
[Network=<NetworkName>]
Syntax
[PXE=<enabled|disabled|UseBios>]
Parameters:
ProfileName
The name of the server profile that contains the connection to modify
The port number of the connection being modified
Port
Properties:
NetworkName
The name of the Ethernet network to associate with the connection.
Applies to Ethernet network connections only.
Command line 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
PXE
Enables or disables PXE on a connection. Valid values are enabled,
disabled, and UseBios. Applies to Ethernet network connections only.
PXE can be enabled on one connection per profile.
Examples:
->set enet-connection MyProfile 2
NetworkName=NewNetworkName
Changes the network of an Ethernet connection
->set enet-connection RedProfile 1 NetworkName=""
Sets a network connection to "unassigned"
->set enet-connection GreenProfile 3 PXE=disabled
Disables PXE on an Ethernet connection
external-manager
Manage external manager settings and information.
Supported actions: delete, help, set, show
Item
Description
show external-
manager
Display the information of an existing external manager
show external-manager
Syntax
Examples:
->show external-manager
Displays the information of an existing external manager.
->show external-manager
Displays the information of an existing external manager in the specified output
format.
->show external-manager
Displays the information of an existing external manager in the specified output
format.
Item
Description
remove external-
manager
Remove an existing manager and regain control of the VC Manager
remove external-manager UserName=<username>
Syntax
Properties:
UserName
A valid external manager user name
->remove external-manager UserName=<username>
Example
Removes external management control of the VC Manager
Item
Description
set external-
manager
Modify external manager configuration properties
set external-manager UserName=<username>
Enabled=<true|false>
Syntax
Command line 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Examples:
->set external-manager UserName=steve Enabled=false
Disables the external manager
->set external-manager UserName=steve Enabled=true
Enables the external manager
fabric
Manage Fibre Channel SAN fabrics.
Support actions: help, set, show
Item
Description
set fabric
Modify an existing FC SAN fabric
set fabric <FabricName> [Name=<NewName>] [NumPorts=<1|2|4>]
[PortSpeed=<Auto|2Gb|4Gb>]
Syntax
Parameters:
FabricName
The name of an existing FC SAN fabric to modify (required)
Properties:
Name
The new name of the fabric
NumPorts
The number of uplink ports to use for the fabric
The port speed for the uplink ports in the fabric
PortSpeed
Examples:
->set fabric MyFabric NumPorts=2
Changes the number of ports used by the fabric
->set fabric Blue Name=Red
Changes the name of an existing fabric from "Blue" to "Red"
->set fabric GreenFabric PortSpeed=4Gb
Changes the port speed of the uplinks in a fabric
Item
Description
show fabric
Display all FC SAN fabrics
show fabric [<FabricName> | *]
Syntax
Examples:
->show fabric
Displays a summary listing of all FC SAN fabrics
->show fabric *
Displays detailed information for all FC SAN fabrics
->show fabric SAN_5
Displays detailed information for a specific FC SAN fabric
Command line 16
Download from Www.Somanuals.com. All Manuals Search And Download.
fc-connection
Manage Fibre Channel SAN fabric connections.
Supported actions: add, help, set
Item
Description
add fc-connection
Add a new FC SAN connection to an existing server profile
add fc-connection <ProfileName> [Fabric=<FabricName>]
[Speed=<Auto|2Gb|4Gb|Disabled>]
Syntax
Parameters:
ProfileName
The name of an existing profile to which the new connection is added.
(required)
Properties:
Fabric
The name of an existing fabric to associate with the connection. If the fabric
name is not specified, it will be assigned to the next available SAN Fabric.
Speed
The port speed of the connection port. Valid values include Auto, 2Gb, 4Gb,
and Disabled. If not specified, then the default port speed is set to "Auto".
AddressType
The source of WWN address assignments to be used during the creation of
the new connection. If not specified, the default is the domain default. If
"UserDefined" is specified, then both a Port WWN and Node WWN must
also be specified. Valid values include Vc-Defined, Factory-Default, and User-
Defined.
PortWWN
NodeWWN
The user-defined Port WWN address to use for the connection. This property
is required if the AddressType specified is "User-Defined".
The user-defined Node WWN address to use for the connection. This
property is required if the AddressType specified is "User-Defined".
Examples:
->add fc-connection MyNewProfile Fabric=SAN_5
Adds a new FC SAN fabric connection to a profile
->add fc-connection MyNewProfile Fabric=SomeFabric
Speed=4Gb
Adds a new FC SAN connection and configures the port speed
->add fc-connection MyNewProfile
Adds a new FC SAN connection and uses the next available fabric
->add fc-connection MyNewProfile AddressType=Factory-
Default
Adds a new FC SAN connection and uses factory-default addresses
->add fc-connection MyNewProfile AddressType=Vc-Defined
Adds a new FC SAN connection and uses VC-defined addresses
->add fc-connection MyNewProfile AddressType=User-
Defined PortWWN=50:06:0B:00:00:C2:62:00
NodeWWN=50:06:0B:00:00:C2:62:00
Adds a new FC SAN connection and provides user-defined WWN addresses
Item
Description
set fc-connection
Modify an existing server profile connection
Command line 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
set fc-connection <ProfileName> <Port>
[Fabric=<FabricName>] [Speed=<Auto|2Gb|4Gb|Disabled>]
[BootPriority=<priority>] [BootPort=<portName>]
[BootLun=<LUN>]
Syntax
Parameters:
ProfileName
The name of the server profile that contains the connection to modify
The port number of the connection being modified
Port
Properties:
Fabric
The name of the FC SAN fabric to associate with the connection
Speed
The port speed of the FC SAN connection. Valid values include Auto, 4Gb,
2Gb, and Disabled
BootPriority
BootPort
Controls whether the FC HBA port is enabled for SAN boot and will affect the
BIOS boot order. Valid values include BIOS, Primary, Secondary, Disabled
The target WWPN of the controller interface on the Fibre Channel storage
target. The port name is a 64-bit identifier in the format:
NN:NN:NN:NN:NN:NN:NN:NN, where N is a hexadecimal number
BootLun
The LUN of the volume used for SAN boot. Valid values include an integer
from 0-255.
Examples:
->set fc-connection MyProfile 1 Fabric=SAN_5
Changes the fabric of an FC SAN fabric connection
->set fc-connection RedProfile 2 Fabric=""
Sets a FC SAN fabric connection to "Unassigned"
->set fc-connection BlueProfile 1 Fabric=SAN_7
Changes the FC SAN Fabric of an FC SAN connection
->set fc-connection BlueProfile 1 Speed=4Gb
Changes the port speed of a FC SAN connection
->set fc-connection BlueProfile 1 BootPriority=Primary
BootPort=50:06:0B:00:00:C2:62:00 BootLun=5
Changes the SAN boot priority and sets additional boot parameters
firmware
Display or update Virtual Connection firmware version.
Support actions: help, show, update
Item
Description
show firmware
Display current version of firmware of all interconnect modules in the domain
show firmware
Syntax
Examples:
->show firmware
Displays current version of the firmware
Command line 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
update firmware
Update the firmware on all Virtual Connect modules in the domain
update firmware url=<firmware image address>
Syntax
Example
Updates the firmware on all Virtual Connect modules in the domain
igmp
Manage Ethernet IGMP Snooping settings.
Supported actions: help, set, show
Item
Description
set igmp
Modify Ethernet IGMP Snooping settings
set igmp [Enabled=<true|false>] [Timeout=<interval>]
Syntax
Properties:
Enabled
Enables or disables IGMP Snooping. Valid values include "true" and "false".
Timeout
The idle timeout interval (in seconds) for IGMP Snooping. Valid values include
integers from 1-3600. The default IGMP idle timeout is 260 seconds.
Examples:
->set igmp Enabled=true
Enables IGMP Snooping
->set igmp Enabled=true Timeout=30
Enables IGMP Snooping and sets the idle timeout
Item
Description
show igmp
Display Ethernet IGMP Snooping settings
show igmp
Syntax
->show igmp
Example
Displays IGMP Snooping settings
interconnect
Manage I/O interconnect modules.
Supported actions: help, remove, show
Item
Description
remove interconnect
Remove a module from the domain that has physically been removed from an
enclosure
remove interconnect <ModuleID|*>
Syntax
Parameters:
ModuleID
The ID of the module to remove. The ID is in the format
<EnclosureID>:<BayNumber>
Examples:
Command line 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
->remove interconnect enc0:2
Removes a specific interconnect module (bay 2) from the domain
->remove interconnect *
Removes all interconnect modules from the domain that are not physically
present in any enclosures
->remove interconnect enc0:*
Remove all interconnect modules that are not physically present in a specific
enclosure
Item
Description
show interconnect
Display all interconnect modules known to the domain
show interconnect [ModuleID|*]
Syntax
Examples:
->show interconnect
Displays a summary listing of all interconnect modules
->show interconnect *
Displays detailed information for all interconnect modules
->show interconnect *:5
Displays the detailed information for all enclosures with interconnect modules
in interconnect bay number 5
->show interconnect enc0:*
Displays interconnect modules in all bays of a specific enclosure
->show interconnect enc0:3
Displays detailed information on a specific interconnect module in interconnect
bay 3 of the primary enclosure
ldap
Manage Virtual Connect directory server authentication settings.
Supported actions: help, set, show
Item
Description
set ldap
Syntax
Modify the Virtual Connect directory server settings
set ldap [Enabled=<true|false>]
[LocalUsers=<enabled|disabled>]
[NtAccountMapping=<enabled|disabled>]
[TargetDomain=<domainName>] [IpAddress=<ipAddress>]
[SslPort=<portNum>] [SearchContext1=<string>]
[SearchContext2=<string>] [SearchContext2=<string>]
Properties:
Enabled
Enables or disables directory authentication. Valid values include "true" and
"false".
Command line 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
LocalUsers
Enables or disables local user authentication. Valid values include "Enabled"
and "Disabled".
WARNING: Disabling local users without correctly configuring LDAP
authentication first may result in not being able to log on.
NtAccountMapping
Enables or disables Microsoft® Windows NT® account mapping. This
capability allows you to enter "domain\username". Valid values include
"Enabled" and "Disabled".
TargetDomain
IpAddress
SslPort
The target domain name. The maximum length is 64 characters.
The IP address or DNS name of the directory server
The port to use for LDAP communication. Valid values include a valid port
number between 1 and 65535. The default port number is 636.
SearchContext1
SearchContext2
SearchContext3
First searchable path used to locate the user when the user is trying to
authenticate using directory services.
Second searchable path used to locate the user when the user is trying to
authenticate using directory services.
Third searchable path used to locate the user when the user is trying to
authenticate using directory services.
->set ldap LDAP=enabled IpAddress=192.168.0.124
Example
Enables directory services authentication for users
Item
Description
show ldap
Display LDAP information
show ldap
Syntax
->show ldap
Example
ldap-group
Manage Virtual Connect directory groups.
Supported actions: add, help, remove, set, show
Item
Description
add ldap-group
Syntax
Add a new directory group to the directory services configuration
add ldap-group <GroupName> [Description=<string>]
[Privileges=domain,server,network,storage]
->add ldap-group MyNewGroup Description="Test Group"
Privileges=domain,server
Example
Adds a new directory group
Item
Description
remove ldap-group
Remove an existing directory group
remove ldap-group <GroupName>
Syntax
->remove ldap-group MyGroup
Example
Removes a directory group
Command line 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
set ldap-group
Modify the properties of an existing directory group
set ldap-group <GroupName> [Description=<description>]
[Privileges=<privileges>]
Syntax
Parameters:
GroupName
The name of an existing group to modify
A user-friendly description for the group
Properties:
Description
Privileges
A set of one or more privileges for the group. Valid values include any
combination of "domain","server","network", and "storage".
->set ldap-group MyGroup Description="Test Group"
Privileges=domain,server,network
Example
Modifies a directory group description and privileges
Item
Description
show ldap-group
Display the existing directory groups
show ldap-group
Syntax
->show ldap-group
Example
Display LDAP group information
mac-cache
Manage Ethernet MAC Cache failover settings.
Supported actions: help, set, show
Item
Description
set mac-cache
Modify Ethernet MAC Cache failover settings
set mac-cache [Enabled=<true|false>] [Refresh=<interval>]
Syntax
Properties:
Enabled
Enables or disables MAC cache failover. Valid values include "true" and "false".
Refresh
The refresh interval for the MAC Cache (in seconds). Valid values include integers
from 1-30.
Examples:
->set mac-cache Enabled=true
Enables MAC Cache Failover
->set mac-cache Enabled=true Refresh=10
Enables MAC Cache Failover and sets the refresh interval
Item
Description
show mac-cache
Display Ethernet MAC Cache failover settings
show mac-cache
Syntax
->show mac-cache
Example
Displays Ethernet MAC Cache failover settings
Command line 22
Download from Www.Somanuals.com. All Manuals Search And Download.
network
Manage Virtual Connect Ethernet networks.
Supported actions: add, help, remove, set, show
Item
Description
add network
Create a new Ethernet Network. After the network has been created, uplink ports
can be added, if the network is not using a shared uplink port set.
add network <NetworkName> [UplinkSet=<UplinkSetName>
VLanID=<VLanID>] [State=<Enabled|Disabled>]
[SmartLink=<Enabled|Disabled>]
Syntax
Parameters:
NetworkName
The unique name of the new network to create (required)
Properties:
UplinkSet
The name of an existing shared uplink port set to use with this new network
(optional). If this property is specified, then a valid VLAN ID must also be provided.
VLanID
The VLAN ID associated with the network (used with shared uplink port set only). The
VLAN ID is a valid number between 1 and 4094.
State
Enables or Disables the network. Valid values are "Enabled" and "Disabled". The
default value is "Enabled".
SmartLink
Enables or Disables the SmartLink capability for a port. Valid values are "Enabled"
and "Disabled". The default value is "Disabled".
Examples:
->add network MyNewNetwork
Creates a new network, and then adds it to the domain
->add network MyNewNetwork2 UplinkSet=MyUplinkSet VLanID=145
Creates a new network and uses a shared uplink port set
->add network Network1 State=Disabled SmartLink=Enabled
Creates a new network with SmartLink Enabled and Status Disabled
Item
Description
remove network
Remove a network from the domain
remove network <NetworkName | *>
Syntax
Parameters:
NetworkName
The name of an existing network in the domain
Examples:
->remove network MyNetwork
Removes a network
->remove network *
Removes all networks
Item
Description
set network
Modify an existing Ethernet network
set network <NetworkName> [Name=<NewName>]
[State=<Enabled|Disabled>] [SmartLink=<Enabled|Disabled>]
Syntax
Command line 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Parameters:
NetworkName
The name of an existing network to modify
Properties:
Name
The new name of the network
State
Enables or disables the network. Valid values are "Enabled" and "Disabled"
Enables or disables the SmartLink capability for a port
SmartLink
Examples:
->set network MyNetwork State=Disabled
Disables an existing network named "MyNetwork"
->set network Blue Name=Red
Changes the name of an existing network from "Blue" to "Red"
->set network GreenNetwork SmartLink=Enabled
Enables the SmartLink feature on a specific network
Item
Description
show network
Display all Ethernet networks in the domain
show network [<NetworkName> | *]
Syntax
Examples:
->show network
Displays a summary listing of all networks
->show network *
Displays detailed information for all networks
->show network MyNetwork
Displays detailed information for a specific network
profile
Manage server profiles.
Supported actions: add, assign, help, remove, set, show, unassign
Item
Description
add profile
Create a new server profile. After the profile has been created, the profile can
then be configured using the "set" subcommand and additional network and
fabric connections can also be added. The server profile can also be assigned to
a device bay using the "assign" subcommand.
add profile <ProfileName> [-NoDefaultEnetConn]
[-NoDefaultFcConn]
Syntax
Parameters:
ProfileName
The unique name of the new server profile to create
Options:
NoDefaultEnetConn
Do not add default Ethernet Network connections when creating the server profile
Do not add default FC SAN connections when creating the server profile
NoDefaultFcConn
Command line 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Examples:
->add profile MyNewProfile
Creates a new profile and adds it to the domain, using default connections
->add profile MyNewProfile2 -NoDefaultEnetConn
Creates a new profile without adding default Ethernet connections
->add profile MyNewProfile2 -NoDefaultFcConn
Creates a new profile without adding default FC connections
->add profile MyNewProfile2 -NoDefaultEnetConn
-NoDefaultFcConn
Creates a new profile without adding default Ethernet and FC connections
Item
Description
assign profile
Assign a server profile to a device bay
assign profile <ProfileName> <DeviceBay>
Syntax
Parameters:
ProfileName
The unique name of the server profile to assign
DeviceBay
The device bay to assign the profile to, in the format:
EnclosureID:DeviceBayNumber
If EnclosureID is not specified it defaults to the local enclosure
->assign profile MyProfile1 enc0:1
Example
Assigns a profile to device bay 1 of the primary enclosure
Item
Description
remove profile
Remove one or more server profiles from the domain
remove profile <ProfileName | *>
Syntax
Examples:
->remove profile MyProfile
Removes a server profile by name
->remove profile *
Removes all server profiles
Item
Description
set profile
Modify properties of an existing server profile
set profile <ProfileName> Name=<NewName>
Syntax
Parameters:
ProfileName
The current name of the profile to modify
Properties:
Name
The new name of the server profile
->set profile MyProfile Name=MyNewProfileName
Example
Changes the name of a server profile
Command line 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
show profile
Display all server profiles that exist in the domain
show profile [<ProfileName> | *]
Syntax
Examples:
->show profile
Displays a summary listing of all server profiles
->show profile *
Displays detailed information for all profiles
->show profile MyProfile
Displays detailed information for a specific profile
Item
Description
unassign profile
Unassign a server profile from a device bay
unassign profile <ProfileName>
Syntax
Parameters:
ProfileName
The name of a server profile that is currently assigned to a device bay
->unassign profile MyProfile1
Example
Unassigns a server profile from a device bay
server
Manage server blades.
Supported actions: help, poweroff, poweron, reboot, show
Item
Description
poweroff server
Power off one or more physical servers
poweroff server [<ServerID> | *] [-Force |
-ForceOnTimeout] [-timeout=<timeout>]
Syntax
Parameters:
ServerID
The reference ID of a physical server in the domain. The format of the server ID is
<EnclosureID:DeviceBay>
If the Enclosure ID is not provided, then the primary or local enclosure is used by
default.
Options:
Force
Forces a power off operation without waiting for the OS to shutdown gracefully.
This option should only be used as a last resort because it can potentially cause
data loss on the server.
ForceOnTimeout
Attempts a graceful power down, but if the server does not shutdown within the
timeout period (default is 60 seconds), then the server will be forced to power
off.
Timeout
Specifies the timeout period (in seconds) to wait for the operation to complete
(per server). The default timeout is 60 seconds.
Examples:
Command line 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
->poweroff server enc0:2
Shuts down a specific server in device bay 2 of an enclosure with ID enc0
->poweroff server enc0:2 -Force
Forces a power off operation on a specific server (primary/local enclosure)
->poweroff server *
Powers off all servers in the domain
->poweroff server enc0:*
Powers off all servers in a specific enclosure
->poweroff server enc0:2 -ForceOnTimeout
Attempts a graceful poweroff, but forces a shutdown if not completed within
timeout period
->poweroff server * -timeout=180
Shuts down all servers and specifies a custom timeout of 3 minutes
Item
Description
poweron server
Power on one or more physical servers
poweron server [<ServerID> | *] [-timeout=<timeout>]
Syntax
Parameters:
ServerID
The reference ID of a server in the domain. The format of the server ID is
<EnclosureID:DeviceBay>
Options:
Timeout
The timeout period (in seconds) to wait for the operation to complete. The default
timeout is 60 seconds.
Examples:
->poweron server 2
Powers on the specific server in bay 2 of the primary enclosure
->poweron server *
Powers on all servers in the domain
->poweron server enc0:*
Powers on all servers in a specific enclosure
Item
Description
reboot server
Reboot one or more physical servers
reboot server [<ServerID>|*] [-Force]
[-ForceOnTimeout] [-timeout=<timeout>
Syntax
Parameters:
ServerID
The reference ID of a server in the domain. The format of the server ID is
<EnclosureID:DeviceBay>.If the Enclosure ID is not provided, then the
primary or local enclosure (enc0) is used by default.
Options:
Force
Forces a reboot operation without waiting for the OS to shutdown gracefully. This
option should only be used as a last resort because it can potentially cause data
loss on the server.
Command line 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
ForceOnTimeout
Attempts a graceful power down, but if the server does not shutdown within the
timeout period (default is 60 seconds), then the server will be forced to reboot.
Timeout
Specifies the timeout period (in seconds) to wait for the operation to complete
(per server). The default timeout is 60 seconds.
Examples:
->reboot server 2
Reboots the specific server in device bay 2 of the primary enclosure
->reboot server enc0:2 -force
Reboots a server using the force option
->reboot server * -ForceOnTimeout -timeout=180
Reboots all servers using the ForceOnTimeout option and a custom timeout
->reboot server *
Reboots all servers in the domain
->reboot server enc0:*
Reboots all servers in a specific enclosure
Item
Description
show server
Display all servers in the domain
show server [<ServerID> | *]
Syntax
Parameters:
ServerID
The reference ID of a server in the domain. The format of the server ID is
<EnclosureID:Bay>
Examples:
->show server
Displays a summary listing of all servers
->show server *
Displays detailed information for all servers
->show server enc0:4
Displays detailed information for the specific server in device bay 4 of an
enclosure named "MyEnclosure"
stackinglink
Display stacking link information and status.
Supported actions: help, show
Item
Description
show stackinglink
Display stacking links and their status
show stackinglink
Syntax
->show stackinglink
Example
Displays a summary listing of all stacking links and status
Command line 28
Download from Www.Somanuals.com. All Manuals Search And Download.
status
View overall domain status information.
Supported actions: help, show
Item
Description
show status
Display the status of the domain and all components in the domain
show status
Syntax
->show status
Example
Displays domain status information
systemlog
View Virtual Connect Manager system event log.
Supported actions: help, show
Item
Description
show systemlog
Display the Virtual Connect manager system log
show systemlog
Syntax
->show systemlog
Example
Displays the system log
uplinkport
Manage interconnect module uplink ports.
Supported actions: add, help, remove, set, show
Item
Description
add uplinkport
Add a new uplink port to an existing network or a shared uplink port set
add uplinkport <PortID> [Network=<NetworkName> |
UplinkSet=<UplinkSet>] [Speed=<Auto|10Mb|100Mb|1Gb|Disabled>]
Syntax
Parameters:
PortID
The ID of an uplink port to add (required). The name is actually a combination of the
enclosure name, interconnect bay, and port number in a single descriptor. The
format of the port name is
"<EnclosureID>:<InterconnectBay>:<PortNumber>". If Enclosure ID is not
specified, it defaults to the local enclosure.
Properties:
Network
The name of an existing network to which the port is added
UplinkSet
Speed
The name of an existing shared uplink port set to which the port is added
Specifies the port speed for the port (optional). Acceptable values include Auto,
10Mb, 100Mb, 1Gb, and Disabled. If not specified, the default port speed is
"Auto".
Examples:
Command line 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
->add uplinkport enc0:1:1 Network=MyNetwork
Adds a new uplink port (Bay 1, Port 1) to a network
->add uplinkport enc0:2:4 Network=MyNetwork Speed=1Gb
Adds a new uplink port (Bay 2, Port 4) to a network and sets the port speed
->add uplinkport enc0:2:3 UplinkSet=MyUplinkSet
Adds a new uplink port (Bay 2, Port 3) to a shared uplink port set
Item
Description
remove uplinkport
Remove an uplink port element from a network or a shared uplink port set
remove uplinkport <PortID> [Network=<NetworkName> |
UplinkSet=<UplinkSetName>]
Syntax
Parameters:
PortID
The name of the port to remove from a network. (required). The port name must be in
the following format:
<EnclosureID>:<InterconnectBayNumber>:<PortNumber>
If EnclosureID is not specified, it defaults to the local enclosure.
The name of the network from which the port is removed
Network
UplinkSet
The name of the shared uplink port set from which the port is removed
Examples:
->remove uplinkport enc0:1:2 Network=MyNetwork
Removes a specific uplink port (Bay 1, Port 2) from a network
->remove uplinkport * Network=BlueNetwork
Removes all uplink ports from a network named "BlueNetwork"
->remove uplinkport enc0:2:3 UplinkSet=SharedUplinkSet1
Removes a specific uplink port (Bay 2, Port 3) from a shared uplink set
Item
Description
set uplinkport
Modify an uplink port that exists as a member of a network or shared uplink port set
set uplinkport <PortID> [Network=<NetworkName> |
UplinkSet=<UplinkSetName>]
Syntax
Speed=<Auto|10Mb|100Mb|1Gb|Disabled>
Parameters:
PortID
The name of the port to modify (required). The specified port must already be added
to a network or uplink port set. The port name is in the format:
<EnclosureID>:<BayNumber>:<PortNumber>
Properties:
Network
The name of the network to which the port belongs
UplinkSet
Speed
The name of the shared uplink port set to which the port belongs
Specifies the port speed for the port. Acceptable values include Auto, 10Mb,
100Mb, 1Gb, and Disabled.
Examples:
->set uplinkport enc0:1:2 Network=MyNetwork Speed=1Gb
Changes the port speed of a network port
Command line 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
->set uplinkport enc0:2:1 Network=MyNetwork Speed=Disabled
Disables a specific port that belongs to a network
->set uplinkport enc0:2:4 UplinkSet=MyUplinkSet
Speed=Disabled
Disables a specific port that belongs to a shared uplink set
Item
Description
show uplinkport
Display all Ethernet module uplink ports
show uplinkport
Syntax
->show uplinkport
Example
Displays all uplink ports
uplinkset
Manage shared uplink port sets
Supported actions: add, help, remove, set, show
Item
Description
add uplinkset
Create a new shared uplink port set
add uplinkset <UplinkSetName>
Syntax
Parameters:
UplinkSetName
The unique name of the new shared uplink port set to create (required)
->add uplinkset MyNewUplinkSet
Example
Creates a new shared uplink port set and adds it to the domain
Item
Description
remove uplinkset
Remove a shared uplink port set from the domain
remove uplinkset <UplinkSetName>
Syntax
Parameters:
UplinkSetName
The name of an existing shared uplink port set
->remove uplinkset MyUplinkSet
Removes a shared uplink port set
Example
Item
Description
set uplinkset
Modify an existing shared uplink port set
set uplinkset <UplinkSetName> [Name=<NewName>]
Syntax
Parameters:
UplinkSetName
The name of an existing shared uplink set to modify
Properties:
Name
The new name of the shared uplink set
->set uplinkset Blue Name=Red
Example
Changes the name of an shared uplink set from "Blue" to "Red"
Command line 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
show uplinkset
Display shared uplink configurations
show uplinkset [<UplinkSetName> | *]
Syntax
Examples:
->show uplinkset
Displays a summary listing of all uplink sets
->show uplinkset *
Displays detailed information for all shared uplink sets
->show uplinkset MyNetwork
Displays detailed information for a specific shared uplink set
user
Manage local domain user configurations.
Supported actions: add, help, remove, set, show
Item
Description
add user
Create a new user and add it to the Virtual Connect Manager database
add user <username> Password=<password> [<optional user
properties>]
Syntax
Properties:
Password
The password of the new user. The password of the new user can be entered as
clear text in the command or as a masked string at the prompt.
FullName
The full name of the user (optional)
ContactInfo
Enabled
Contact information for the user (optional)
Enables or disables the user [true | false] (optional)
Privileges
The allowed privileges for the user (optional). Privileges can be any combination
of "domain", "server", "network", or "storage" separated by commas.
Examples:
->add user steve Password=fgY87hHl
Adds a new user by specifying the minimal amount of properties
->add user bill Password=HGtwf7272562
Privileges="domain,network" FullName="Bill Johnson"
[email protected] Enabled=true
Adds a new user and configures additional user properties
->add user Admin Password=hjkhfd Privileges=*
Adds an "Admin" user with all privileges
Item
Description
remove user
Remove a user from the Virtual Connect Manager database
remove user <username>
Syntax
Examples:
Command line 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
->remove user steve
Removes a specific user by name
->remove user *
Removes all users
Item
Description
set user
Modify attributes of an existing user
set user <username> [<one or more user properties>]
Syntax
Properties:
UserName
The new name of the user
Password
The new password of the user can be entered as clear text in the command or as
a masked string at the prompt. If the Password value is blank, the user is
prompted to enter the password at the prompt.
FullName
The full name of the user
ContactInfo
Enabled
Contact information for the user
Enables or disables the user [true | false]
Privileges
The allowed privileges for the user (optional). Privileges can be any combination
of "domain", "server", "network", "storage" separated by commas.
Examples:
->set user steve Password=fgY87hHl
Modifies an existing user's password
->set user steve Password
Modifies an existing user's password, masked, at the prompt
->set user bill Password=HGtwf7272562
Privileges="domain,network" FullName="Bill Johnson"
[email protected] Enabled=true
Modifies several properties of an existing user
->set user tom privileges=*
Gives a user all privileges
Item
Description
show user
Display user summary or user details
show user [<username>]
Syntax
Properties:
Privileges
The allowed privileges for the user, which can be any combination of "domain",
"server", "network", or "storage" separated by commas
FullName
ContactInfo
Enabled
The full name of the user
Contact information for the user
Specifies if the user is enabled or disabled
Examples:
->show user
Displays a listing of all existing users
Command line 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
->show user steve
Displays details of an existing user by name
->show user *
Displays details of all existing users
vcm
Reset the Virtual Connect Manager.
Supported actions: help, reset
Item
Description
reset vcm
Reset the Virtual Connect Manager. A failover to the standby VCM may
also be specified (optional), if there is a standby VCM available.
IMPORTANT: Resetting the VCM causes a temporary loss in connectivity
with the Virtual Connect Manager. If failover is specified and there is a
standby VCM, users are logged off and must reconnect using the standby
VCM IP address.
Syntax
reset vcm [-failover]
Examples:
->reset vcm
Resets the Virtual Connect Manager
->reset vcm -failover
Resets the Virtual Connect Manager and forces a failover to the standby
VCM (if available)
version
Display CLI version information.
Supported actions: help, show
Item
Description
show version
Display CLI version information
show version
Syntax
->show version
Example
Displays CLI version and copyright information
Help subsystem
The help subsystem consists of three options:
•
Help summary—lists all supported actions and a short description of each:
>help (or ?)
add
add an element to an existing object
assign a server profile to a device bay
assign
Command line 34
Download from Www.Somanuals.com. All Manuals Search And Download.
. . .
•
Subcommand help—displays help details associated with a specific subcommand, including
supported managed elements:
>assign -help (or assign ?)
assign a server profile to a device bay
Managed Elements:
profile
Examples:
assign profile MyProfile enc0:1
•
Management element help—provides a listing of objects that are supported with a specific
subcommand and a brief description of the management element and what it represents in the
management model:
->help devicebay
General Enclosure Device Bay settings and information
Supported Subcommands:
help
show
-----------------------------------------------------------------------
->show devicebay -help
Description:
This command displays all device bays in the domain
Syntax:
show devicebay [<DeviceBayName> | *]
Parameters:
DeviceBayName : The reference name of a device bay in the domain.
The format of the device bay name is
<EnclosureID:DeviceBay>
Examples:
- Display a summary listing of all device bays:
->show devicebay
- Show detailed information for all device bays:
Command line 35
Download from Www.Somanuals.com. All Manuals Search And Download.
->show device bay *
- Show detailed information for a specific device bay 2 of
a specific enclosure:
->show devicebay enc0:2
Output format
The CLI provides two different output formats:
•
•
Interactive user output format
Scriptable output format
The interactive user output format is the default. However, by using a command-line option, the user can
also specify a "parse-friendly" output format, which provides data in a format that can be easily
interpreted by automated scripts invoking the CLI. The different output formats primarily impact the show
subcommand in the CLI infrastructure, where a majority of the informational details are displayed.
Interactive user output format
The interactive user output format provides a user friendly view of information at the command line. When
providing an overview, or listing, of several instances of data, a tabular text format is displayed. If an
individual instance of data is being displayed, then the stanza format is used.
Example 1: Tabular text output format for displaying a user list
->show user
============================================================================
UserName
Privileges FullName
ContactInfo
Enabled
============================================================================
Administrator domain
server
Steve Johnson
[email protected] true
network
storage
----------------------------------------------------------------------------
Admin
domain
server
network
storage
Admin
Admin
true
----------------------------------------------------------------------------
steve
domain
server
network
storage
Steve Johnson
[email protected] true
----------------------------------------------------------------------------
Command line 36
Download from Www.Somanuals.com. All Manuals Search And Download.
brad
domain
server
Brad Mills
true
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----------------------------------------------------------------------------
Example 2: Stanza output format for displaying a single user instance
->show user steve
UserName
Privileges : domain,server,network,storage
FullName : Steve Johnson
ContactInfo : [email protected]
Enabled : true
: steve
Example 3: Stanza output format for displaying all user details
->show user *
UserName
Privileges : domain,server,network,storage
FullName : Steve Johnson
ContactInfo : [email protected]
: Administrator
Enabled
: true
UserName
: Admin
Privileges : domain,server,network,storage
FullName : Admin
ContactInfo : Admin
Enabled
: true
UserName
: steve
Privileges : domain,server,network,storage
FullName : Steve Johnson
ContactInfo : [email protected]
Enabled
: true
UserName
: brad
Privileges : domain,server
FullName : Brad Mills
ContactInfo : [email protected]
Enabled
: true
UserName
: jim
Privileges : network
FullName : Jimmy Joe
ContactInfo : [email protected]
Enabled
: true
Command line 37
Download from Www.Somanuals.com. All Manuals Search And Download.
UserName
: alice
Privileges : storage
FullName
: Alice Candle
ContactInfo : [email protected]
Enabled
: false
Scriptable output format
Scriptable output format allows scripts to invoke CLI commands and receive command responses that can
be easily parsed by the scripts. This capability is provided by two options that are available: -
output=script1 and -output=script2. These options are described in more detail below. To display output
with no headers or labels, use no-headers as an additional output option value.
IMPORTANT: If the delimiter is present within the data, then the entire value is surrounded by
double quotes.
•
•
Script1 Output Format
The script1 output format can be used to format the output using a name-value pair format, using an
equal sign as the delimiter. All text on the left side of the equal sign designates the "name" of a
property, and the text on the right side of the equal sign designates the "value" of the property. If
"no-headers" is provided as an additional option value, only the values are displayed. Each
property is displayed on a separate line.
Script2 Output Format
The script2 output format can be used to format all instance data in a single line, using a semi-colon
as the delimiter for the data. The first line contains the property names. This format is consistent with
a "table view" of the data, where the first line is represented by a list of column labels, while the
remaining lines provide the actual data being displayed. Each line represents a single instance of
data. For example, in the case of showing users, each line provides all data corresponding to a
single user instance.
The following examples provide some common scenarios for using the script output format options.
Example 1: Scriptable output format displaying all enclosures
->show enclosure -output=script1
ID=enc0
Name=Enclosure1
Import Status=Imported
Serial Number=USE0000BK2
Part Number=403321-021
Asset Tag=OA ASSET 453
Example 2: Scriptable output format displaying user "Administrator" information
->show user Administrator -output=script1
User Name=Administrator
Privileges=domain,server,network,storage
Full Name=
Contact Info=
Enabled=true
Command line 38
Download from Www.Somanuals.com. All Manuals Search And Download.
Example 3: Scriptable output format displaying all users (with table header)
->show user -output=script2
UserName;Privileges;FullName;ContactInfo;Enabled
Administrator;domain,server,network,storage;Steve
Johnson;[email protected];true
Admin;domain,server,network,storage;Admin;Admin;true
steve;domain,server,network,storage;Steve
Johnson;[email protected];true
Example 4: Scriptable output format displaying all users (no table header)
->show user -output=script2,no-headers
Administrator;domain,server,network,storage;Steve
Johnson;[email protected];true
Admin;domain,server,network,storage;Admin;Admin;true
steve;domain,server,network,storage;Steve
Johnson;[email protected];true
Example 5: Scriptable output format displaying a single user (with table header)
->show user steve -output=script2
UserName;Privileges;FullName;ContactInfo;Enabled
steve;domain,server,network,storage;Steve
Johnson;[email protected];true
Example 6: Scriptable output format displaying a single user (no table header)
->show user steve -output=script2,no-headers
steve;domain,server,network,storage;Steve
Johnson;[email protected];true
Command line 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the Virtual Connect domain using
the CLI
Basic configuration
A Virtual Connect domain consists of an enclosure and a set of associated modules and server blades that
are managed together by a single instance of the Virtual Connect Manager. The Virtual Connect domain
contains specified networks, server profiles, and user accounts that simplify the setup and administration
of server connections. Establishing a Virtual Connect domain enables administrators to upgrade, replace,
or move servers within their enclosures without changes being visible to the external LAN/SAN
environments.
Before getting started, perform the following tasks:
•
Verify that the HP Onboard Administrator is running the latest firmware (must be at least v1.30 or
later).
•
Locate the Default Network Settings label attached to the HP 1/10Gb VC-Enet module in
interconnect module bay 1 and note the following information:
o
o
o
DNS name
User name
Password
•
Connect any Ethernet module stacking cables
IMPORTANT: After a CLI command is issued, it can take up to 90 seconds before
configuration changes are stored in persistent memory. Disruptive actions such as powering
cycling an I/O module within this time window can result in lost configuration changes.
The following sections provide the necessary steps to set up a basic domain.
Logging in to the CLI
•
SSH
>ssh 192.168.0.120
login as: Administrator
password:
•
Local User Authentication using default Administrator login credentials
>ssh 192.168.0.120
login as: Administrator
Configuring the Virtual Connect domain using the CLI 40
Download from Www.Somanuals.com. All Manuals Search And Download.
password: <Default Administrator login credentials>
•
LDAP Authentication
>ssh 192.168.0.120
login as: <LDAP user>
password: <password>
Domain setup
A Virtual Connect domain consists of an enclosure and a set of associated modules and server blades that
are managed together by a single instance of the Virtual Connect Manager. the Virtual Connect domain
contains specified networks, server profiles, and user accounts that simplify the setup and administration
of server connections. Establishing a Virtual Connect domain enables administrators to upgrade, replace,
or move servers within their enclosures without changes being visible to the external LAN/SAN
environments.
Before getting started, perform the following tasks:
•
•
Verify that the Onboard Administrator is running the latest firmware (must be at least v1.30 or later).
Locate the Default Network Settings label attached to the HP 1/10Gb VC-Enet Module in
interconnect module bay 1 and note the following information:
o
o
o
DNS name
User name
Password
•
Connect any Ethernet module stacking cables
After logging in, perform the following tasks to setup the domain:
1.
2.
3.
Import the enclosure.
Name the domain.
Set up local user accounts and privileges.
Importing an enclosure
Enter OA credentials during import:
>import enclosure username=Administrator password=myPassword
or
>import enclosure username=Administrator
Password=*****
Setting the domain name
To set the domain name, use the set domain command:
>set domain name=MyNewDomainName
The Virtual Connect domain name must be unique within the data center, and can be up to 64 characters
without spaces or special characters.
Configuring local users
•
Add a new user
Configuring the Virtual Connect domain using the CLI 41
Download from Www.Somanuals.com. All Manuals Search And Download.
>add user bob password=fhkjdhfk privileges=domain,network
•
•
•
Modify an existing user
>set user bob fullname="Bob J Smith" enabled=false
Remove an existing user
>remove user bob
Remove all local users except for the Administrator account
>remove user *
Display local users:
•
•
•
Summary display
>show user
Detailed display
>show user *
Displaying info on a single user
>show user steve
Up to 32 local user accounts can be created.
Each account can be set up to have a combination of up to four access privileges:
•
Domain
o
o
o
o
o
o
o
o
o
Define local user accounts, set passwords, define roles
Import enclosures
Name the VC domain
Set the domain IP address
Update firmware
Administer SSL certificates
Delete the VC domain
Save configuration to disk
Restore the configuration from a backup
•
•
•
Networking
o
o
o
o
Configure network default settings
Select the MAC address range to be used by the VC domain
Create, delete, and edit networks
Create, delete, and edit shared uplink sets
Server
o
o
o
o
Create, delete, and edit server Virtual Connect profiles
Assign and unassign profiles to device bays
Select and use available networks
Power on and off server blades within the enclosure
Storage
o
o
Select the WWNs to be used by the domain
Setup the connections to the external FC Fabrics
Configuring the Virtual Connect domain using the CLI 42
Download from Www.Somanuals.com. All Manuals Search And Download.
It is possible to create a user with no privileges. This user can only view status and settings.
NOTE: The vcmuser_ account is an internal Onboard Administrator account created and used
by Virtual Connect Manager to communicate with the Onboard Administrator. This account
can show up in the Onboard Administrator system log. This account cannot be changed or
deleted.
Configuring LDAP authentication support for users
•
Set LDAP properties
>set ldap ipaddress=192.168.0.110 enabled=true
•
Add/Remove LDAP directory groups
>add ldap-group MyNewGroup description="This is my test group"
privileges=domain,server,network
•
•
Enable/Disable local users
>set ldap localusers=disabled
Display LDAP settings and directory groups
>show ldap
>show ldap-group
Network setup
To establish external Ethernet network connectivity for the HP BladeSystem c-Class enclosure, do the
following:
1.
Identify the MAC addresses to be used on the server blades deployed within this Virtual Connect
domain.
2.
Setup connections from the HP BladeSystem c-Class enclosure to the external Ethernet networks.
These connections can be uplinks dedicated to a specific Ethernet network or shared uplinks that
carry multiple Ethernet networks with the use of VLAN tags.
Configuring MAC Address ranges
•
•
•
Use VC-Defined MAC addresses
>set domain MacType=VC-Defined MacPool=10
Use factory-default MAC addresses
>set domain MacType=Factory-Default
Set user-defined MAC addresses
>set domain MacType=User-Defined MacStart=00-17-A4-77-00-00 MacEnd=00-
17-A4-77-00-FF
IMPORTANT: Configuring Virtual Connect to assign server blade MAC addresses requires
careful planning to ensure that the configured range of MAC addresses is used once within the
environment. Duplicate MAC addresses on an Ethernet network can result in a server network
outage.
Each server blade Ethernet NIC ships with a factory default MAC address. The MAC address is a 48-bit
number that uniquely identifies the Ethernet interface to other devices on the network. While the hardware
ships with default MAC addresses, Virtual Connect has the ability to assign MAC addresses that will
Configuring the Virtual Connect domain using the CLI 43
Download from Www.Somanuals.com. All Manuals Search And Download.
override the factory default MAC addresses while the server remains in that Virtual Connect enclosure.
When configured to assign MAC addresses, Virtual Connect securely manages the MAC addresses by
accessing the physical NICs through the enclosure Onboard Administrator and the iLO interfaces on the
individual server blades.
Always establish control processes to ensure that a unique MAC address range is used in each Virtual
Connect domain in the environment. Reusing address ranges could result in server network outages
caused by multiple servers having the same MAC addresses.
If using Virtual Connect assigned MAC addresses, the following notes apply:
•
Virtual Connect automatically reserves both a primary address and an iSCSI MAC address for use
by multifunction gigabit server adapters, such as the HP NC373m PCI Express Dual Port
Multifunction Gigabit server adapter. Only the primary MAC address is used by standard (not
multifunction) Ethernet devices.
•
•
If a server blade is moved from a Virtual Connect managed enclosure to a non-Virtual Connect
enclosure, the local MAC addresses on that server blade are automatically returned to the original
factory defaults.
If a server blade is removed from a bay within a Virtual Connect domain and installed in another
bay in the same Virtual Connect domain or in a bay in a different domain, it is assigned the new set
of addresses appropriate for that server location.
Assigned MAC addresses
The MAC address range used by the Virtual connect domain must be unique within the environment. HP
provides a set of pre-defined ranges that are for use by Virtual Connect Manager and will not conflict
with server factory default MAC addresses.
When using the HP-defined MAC address ranges, ensure that each range is used only once within the
environment.
Selecting VC-assigned MAC address ranges
When using VC-assigned MAC addresses, you can choose between using an HP pre-defined MAC
address range or using a user-defined MAC address range.
•
HP pre-defined MAC address range (recommended). These pre-defined ranges are reserved and will
never show up as factory default on any hardware. There are 64 ranges of 1024 unique addresses
to choose from. Be sure to use each range only once within a data center.
•
User-defined MAC address range. To avoid potential conflict with other hardware MAC addresses
in the environment, consider using a subrange of MAC addresses reserved by the IEEE for locally-
administered MAC addresses. Ensure that the range does not conflict with any Ethernet device
already deployed within the enterprise.
IMPORTANT: If you plan to use RDP for RedHat Linux installation and also plan to use User- or
HP-defined MAC addresses, you must import the enclosure before running RDP.
Select the type and range of MAC address, and then click Next.
NOTE: After any server profiles are deployed using a selected MAC address range, that
range cannot be changed until all server profiles are deleted.
Configuring the Virtual Connect domain using the CLI 44
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating an enet-network
To create a new Ethernet network use the add networkcommand:
>add network MyNetworkName
Modifying enet-network properties
To modify Ethernet network properties, use the set networkcommand:
>set network MyNetworkName state=enabled name=NewName smartlink=enabled
Displaying enet-networks
To display Ethernet network properties, use the show networkcommand:
•
•
•
Summary display
>show network
Detailed display
>show network *
Single network display
> show network MyNetwork
Adding uplink ports to an enet-network
To add uplink ports to an existing Ethernet network, use the add uplinkport command:
>add uplinkport enc0:1:1 network=MyNetwork
>add uplinkport 1:1 network=MyNetwork
Modifying uplink port properties
To modify an uplink port that exists as a member of a network or shared uplink set, use the set
uplinkport command:
>set uplinkport network=Network1 speed=1Gb
Creating a shared uplink port set
To create a shared uplink port set, use the add uplinksetcommand:
>add uplinkset MyUplinkSetName
A shared uplink set is a way of identifying HP 1/10Gb VC-Enet module uplinks that will carry multiple
networks over the same cable. In this case, each Ethernet packet carries a VLAN tag (IEEE 802.1Q) to
identify the specific network to which it belongs. On shared uplinks, the VLAN tags are added when
packets leave the VC-enabled enclosure and are removed when packets enter the enclosure. The external
Ethernet switch and the Virtual Connect Manager must be configured to use the same VLAN tag identifier
(a number between 1 and 4094) for each network on the shared uplink(s).
Virtual Connect places no special restrictions on which VLAN identifiers can be used, so the VLAN IDs
already used for the networks in the data center can be used on these shared uplinks. To configure a
shared uplink set for VLAN tagging, obtain a list of the network names and their VLAN IDs.
A shared uplink set enables multiple ports to be included to support port aggregation and link failover
with a consistent set of VLAN tags.
Configuring the Virtual Connect domain using the CLI 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Because VLAN tags are added or removed when Ethernet packets leave or enter the VC-Enet shared
uplink, the VLAN tags have no relevance after the Ethernet packet enters the enclosure.
IMPORTANT: If you are deploying a server where VLAN tags will be used (added) on the
server itself, do not connect the server Ethernet port carrying VLAN-tagged traffic to a shared
uplink set.
Identifying an associated network as the native VLAN causes all untagged incoming Ethernet packets to
be placed onto this network. Only one associated network can be designated as the native VLAN. All out-
going Ethernet packets are VLAN tagged.
Displaying shared uplink port sets
•
•
•
Summary display
>show uplinkset
Detailed display
>show uplinkset *
Single uplinkset display
>show uplinkset MyUplinkSetName
Adding uplink ports to a shared uplink port set
To add uplink ports to a shared uplink port set, use the add uplinkportcommand:
>add uplinkport enc0:1:2 uplinkset=MyUplinkSetName
Creating a network that uses a shared uplink port set
To create a network that uses a shared uplink port set, use the add networkcommand:
>add network MyNewNetworkName uplinkset=MyUplinkSetName vlanid=156
Fibre Channel setup
To configure external Fibre Channel connectivity for the HP BladeSystem c-Class enclosure, do the
following:
1.
2.
Identify WWNs to be used on the server blades deployed within this Virtual Connect Domain.
Define available SAN fabrics.
Configuring WWN address ranges
•
VC-Defined
>set domain WwnType=VC-Defined WwnPool=5
•
Factory-Default
>set domain WwnType=Factory-Default
Each server blade FC HBA mezzanine card ships with factory default port and node WWNs for each FC
HBA port. Each WWN is a 64-bit number that uniquely identifies the FC HBA port/node to other devices
on the network. While the hardware ships with default WWNs, Virtual Connect has the ability to assign
WWNs that will override the factory default WWNs while the server remains in that Virtual Connect
enclosure. When configured to assign WWNs, Virtual Connect securely manages the WWNs by
Configuring the Virtual Connect domain using the CLI 46
Download from Www.Somanuals.com. All Manuals Search And Download.
accessing the physical FC HBA through the enclosure Onboard Administrator and the iLO interfaces on
the individual server blades.
When assigning WWNs to a FC HBA port, Virtual Connect will assign both a port WWN and a node
WWN. Because the port WWN is typically used for configuring fabric zoning, it is the WWN displayed
throughout the Virtual Connect user interface. The assigned node WWN is always the same as the port
WWN incremented by one.
Configuring Virtual Connect to assign WWNs in server blades maintains a consistent storage identity
(WWN) even when the underlying server hardware is changed. This method allows server blades to be
replaced without affecting the external Fibre Channel SAN administration.
CAUTION: To avoid storage networking issues and potential loss of data associated with
duplicate WWNs on a FC SAN fabric, plan carefully when allowing Virtual Connect to assign
server blade WWNs so that the configured range of WWNs is used only once within the
environment.
The WWN range used by the Virtual Connect domain must be unique within the environment. HP
provides a set of pre-defined ranges that are reserved for use by Virtual Connect and will not conflict with
server factory default WWNs.
When using the HP-defined WWN ranges, be sure that each range is used only once within the
environment.
Modifying FC fabric properties
To modify the properties of an existing FC SAN fabric, use the set fabriccommand:
>set fabric name=MyNewName portspeed=4Gb
Each HP 4Gb VC-FC module can be connected to one external FC SAN fabric. All uplinks must be on the
same fabric. Use this command to:
•
•
•
Name the FC SAN fabric connected to each VC-FC module.
Set the number of uplinks to be used (1, 2, or 4).
Select the uplink port speed to be used on each VC-FC module.
The number of enabled uplinks and the number of servers in the enclosure determines the effective
oversubscription for that FC connection. For additional information on Fibre Channel mapping, see the HP
Virtual Connect for c-Class BladeSystem User Guide.
Displaying FC fabrics
To display a list of all FC SAN fabrics, use the show fabriccommand:
>show fabric
Server Profile setup
A Virtual Connect server profile is a logical grouping of attributes related to server connectivity that can
be assigned to a server blade. With the Virtual Connect v1.10 and higher, the server profile can include
MAC address, PXE, and network connection settings for each server NIC port and WWN, SAN fabric
connection, and SAN boot parameter settings for each Fibre Channel HBA port. After being defined, the
server profile can be assigned to any server blade within the Virtual Connect domain. A Virtual Connect
domain can have a maximum of 64 Virtual Connect server profiles.
Configuring the Virtual Connect domain using the CLI 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Virtual Connect v1.20 adds the ability to configure PXE settings when using either VC Assigned or factory
default MAC addresses. In addition, Use BIOS is a new option for PXE, which maintains the current
settings as configured by RBSU.
A new feature in Virtual Connect v1.20 is the ability to override the Virtual Connect assigned MACs
and/or WWNs when creating a new profile.
When a server profile is assigned to a server blade, the Virtual Connect Manager securely connects to the
server blade, configures the NIC ports with the appropriate MAC addresses and PXE settings, and
configures the FC HBA ports with the appropriate WWNs and SAN boot settings. In addition, the Virtual
Connect Manager automatically connects the server blade Ethernet and Fibre Channel ports to the
specified networks and SAN fabrics. This server profile can then be re-assigned to another server blade
as needed, while maintaining the server's network and SAN identity and connectivity.
The Virtual Connect Manager can be configured so that server blades use server factory default
MACs/WWNs or Virtual-Connect-administered MACs/WWNs. These administered values override the
default MAC addresses and WWNs when a server profile is assigned to a server, and appear to pre-
boot environments and host operating system software as the hardware addresses. To use administered
MAC addresses, select a range of HP pre-defined or user-specified MAC addresses.
Be sure to review the following list of guidelines before creating and deploying server profiles:
•
•
•
•
•
The server blade firmware and option card firmware must be at a revision that supports Virtual
Before creating the first server profile, select whether to use moveable, administered MAC addresses
and WWNs or whether to use the local server blade factory default MAC addresses and WWNs.
After an enclosure is imported into a Virtual Connect domain, server blades remain isolated from the
networks and SAN fabrics until a server profile is created and assigned.
Server blades must be powered off to receive (or relinquish) a server profile assignment when using
Virtual Connect-administered MAC addresses, WWNs, or changing Fibre Channel boot parameters.
FC SAN Connections are only shown in server profile screens when there is an HP Virtual Connect
Fibre Channel Module in the enclosure managed by Virtual Connect. FC SAN Connections are
added in pairs and cannot be deleted. If an HP Virtual Connect Fibre Channel Module is added to a
Virtual Connect domain that has existing profiles, an option to add FC connections appears in the
existing profiles when editing.
•
•
Some server profile SAN boot settings (controller boot order) are only applied by Virtual Connect
after the server blade has been booted at least once with the final mezzanine card configuration.
If PXE, controller boot order, or SAN boot settings are made outside of Virtual Connect (using RBSU
or other configuration tools), Virtual Connect will restore the settings defined by the server profile
after the server blade completes the next boot cycle.
•
If using a QLogic HBA with some versions of Linux (RHEL3, RHEL4, SLES9, and SLES10), the HBA
connection type must be set to "point to point only" in the adapter configuration settings in the
QLogic BIOS utility or QLogic OS utility (if available). If the HBA settings are not changed, the HBA
may be unable to log into the fabric and discover devices on the SAN.
Server profiles are associated with a specific enclosure device bay. After a profile is assigned, the Virtual
Connect Manager configures the server blade in that device bay with the appropriate
MAC/PXE/WWN/SAN boot settings and connects the appropriate networks and fabrics. Server blades
that have been assigned a profile and remain in the same device bay do not require further Virtual
Connect Manager configuration during server or enclosure power cycle. They will boot and gain access
to the network and fabric when the server and interconnect modules are ready.
Configuring the Virtual Connect domain using the CLI 48
Download from Www.Somanuals.com. All Manuals Search And Download.
If a server blade is inserted into a device bay already assigned a server profile, Virtual Connect Manager
automatically updates the configuration of that server blade before it is allowed to power up and connect
to the network.
If a server blade is moved from a Virtual Connect managed enclosure to a non-Virtual Connect enclosure,
local MAC addresses and WWNs are automatically returned to the original factory defaults. This feature
prevents duplicate MAC addresses and WWNs from appearing in the data center because of a server
blade redeployment.
NOTE: If you are using server factory default MAC addresses WWNs and default Fibre
Channel boot parameters, you do not have to power off a server to make any profile changes.
If you are using HP assigned or user assigned MAC addresses or WWNs, you must power a
server off when moving a profile to the server or away from the server.
Creating server profiles
To create a new server profile, use the add profilecommand:
>add profile MyProfile
After an enclosure is imported into a Virtual Connect domain, server blades that have not been assigned
a server profile are isolated from all networks to ensure that only properly configured server blades are
attached to data center networks.
A server profile can be assigned and defined for each device bay so that the server blade can be
powered on and connected to a deployment network. These profiles can then later be modified or
replaced by another server profile.
A server profile can also be assigned to an empty bay to allow deployment at a later date.
Adding enet-network connections to a profile
To add a new Ethernet network connection to an existing server profile, use the add enet-connection
command:
>add enet-connection MyProfile network=MyNetwork pxe=enabled
Adding FC fabric connections to a server profile
To add a new FC SAN connection to an existing server profile, use the add fc-connection
command:
>add fc-connection MyProfile fabric=SAN_5
Assigning a server profile to device bay 1
To assign a server profile to a specific device bay, use the assign profilecommand:
>assign profile MyProfile enc0:1
>assign profile MyProfile 1
Configuring IGMP settings
To set Ethernet IGMP snooping properties, use the set igmpcommand:
> set igmp enabled=true timeout=30
Configuring the Virtual Connect domain using the CLI 49
Download from Www.Somanuals.com. All Manuals Search And Download.
IGMP allows VC-Enet modules to monitor (snoop) the IP multicast membership activities and to configure
hardware Layer 2 switching behavior of multicast traffic to optimize network resource usage. Currently
only IGMP v1 and v2 (RFC2236) are supported.
The IGMP Snooping idle timeout interval is set to 260 seconds by default. This value is basically the
"Group Membership Interval" value as specified by IGMP v2 specification (RFC2236). For optimum
network resource usage, set the interval to match the configuration on the customer network's multicast
router settings.
Configuring MAC cache failover settings
•
To configure MAC Cache Failover Settings, use the set mac-cachecommand:
>set mac-cache enabled=true refresh=10
•
To dispaly MAC Cache Failover Settings, use the show mac-cachecommand:
>show mac-cache
When a VC-Enet uplink that was previously in standby mode becomes active, it can take several minutes
for external Ethernet switches to recognize that the c-Class server blades can now be reached on this
newly-active connection. Enabling Fast MAC Cache Failover causes Virtual Connect to transmit Ethernet
packets on newly-active links, which enables the external Ethernet switches to identify the new connection
(and update their MAC caches appropriately.) This transmission sequence repeats a few times at the
MAC refresh interval (5 seconds recommended) and completes in about 1 minute.
IMPORTANT: Be sure to set switches to allow MAC addresses to move from one port to
another without waiting for an expiration period or causing a lock out.
Logging out of the CLI
To log out of the CLI, use the exitcommand:
>exit
Common management operations
The following table provides the syntax for the most commonly used management operations.
Operation
Examples
>show domain
Display general domain settings
Display predefined address pools
Display interconnect modules
>show domain addresspool
•
•
•
Summary display
>show interconnect
Detailed display
>show interconnect *
Single module display
>show interconnect enc0:2
>show interconnect 4
>show status
Display overall domain status
Configuring the Virtual Connect domain using the CLI 50
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Examples
>show stackinglink
>show systemlog
Display stacking link configuration and status
Display the system log
Display a list of servers in the domain
•
•
•
Summary display
>show server
Detailed display
>show server *
Single server display
>show server enc0:1
>show server 2
Display server profiles
•
•
•
Summary display
>show profile
Detailed display
>show profile *
Single profile display
>show profile MyProfile
>delete domain
Delete the domain configuration
>update firmware
1.20.rom
Update interconnect module firmware
>reset vcm - failover
Force a failover to the standby VC Manager
Power off server blades
>poweroff server enc0:2
>poweroff server 3
>poweroff server *
>poweron server enc0:1
>poweron server 2
Power on server blades
Reset a server blade
>poweron server *
>reboot server enc0:4
>reboot server 6
>reboot server *
>unassign profile MyProfile
Unassign a server profile from a device bay
Modify Ethernet network connection properties
>set enet-connection MyProfile 1
pxe=disabled
>set fc-connection MyProfile 2 speed=auto
Modify FC fabric connections
Resetting the Virtual Connect Manager
To reset the Virtual Connect Manager, use the reset vcmcommand:
>reset vcm
>reset vcm [-failover]
Administrator privileges are required for this operation.
If VC Ethernet Modules are installed in I/O bays 1 and 2 of the enclosure, the user can manually change
which Virtual Connect Ethernet Module is hosting the Virtual Connect Manager through the use of this
feature. The feature can also force the Virtual Connect manager to restart without switching to the
Configuring the Virtual Connect domain using the CLI 51
Download from Www.Somanuals.com. All Manuals Search And Download.
alternate Virtual Connect Ethernet module. This feature can be useful when troubleshooting the Virtual
Connect manager. The network and FC processing of the Virtual Connect subsystem is not disturbed
during the restart or failover of the Virtual Connect Manager.
If the command line option -failoveris included in the reset vcmcommand and a Virtual Connect
Ethernet module is available in the alternate I/O bay (I/O Bays 1 and 2 can host the Virtual Connect
Manager), the command line displays the message:
SUCCESS: The Virtual Connect Manager is being reset. Please wait...
The user is logged out of the session after approximately 1 minute. An attempted login to the same Virtual
Connect Ethernet Module is rejected with the message:
Virtual Connect Manager not found at this IP address.
If the user attempts to login to the alternate I/O bay, they might receive the error message during the
attempted login:
Unable to communicate with the Virtual Connect Manager. Please retry
again later.
The login should succeed after the Virtual Connect Manager has restarted on this alternate Virtual
Connect Ethernet module. Allow up to 5 minutes, depending on the enclosure configuration.
If the command line option -failoveris not included in the reset vcmcommand or a Virtual Connect
Ethernet module is not available in the alternate I/O bay, the command line displays the message:
SUCCESS: The Virtual Connect Manager is being reset. Please wait...
The user is logged out of the session after approximately 1 minute. If the user attempts to re-login they
might receive the error message during the attempted login:
Unable to communicate with the Virtual Connect Manager. Please retry
again later.
The login should succeed after the Virtual Connect Manager has restarted. Allow up to 5 minutes,
depending on the enclosure configuration.
Configuring the Virtual Connect domain using the CLI 52
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical support
Before you contact HP
Be sure to have the following information available before you call HP:
•
•
•
•
•
•
•
•
Technical support registration number (if applicable)
Product serial number
Product model name and number
Product identification number
Applicable error messages
Add-on boards or hardware
Third-party hardware or software
Operating system type and revision level
HP contact information
For the name of the nearest HP authorized reseller:
•
•
In other locations, see the Contact HP worldwide (in English) webpage
For HP technical support:
•
In the United States, for contact options see the Contact HP United States webpage
o
Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a
week. For continuous quality improvement, calls may be recorded or monitored.
o
If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more
•
In other locations, see the Contact HP worldwide (in English) webpage
Technical support 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Acronyms and abbreviations
BIOS
Basic Input/Output System
CLI
Command Line Interface
DHCP
Dynamic Host Configuration Protocol
DNS
domain name system
FC
Fibre Channel
HBA
host bus adapter
I/O
input/output
IGMP
Internet Group Management Protocol
IP
Internet Protocol
iSCSI
Internet Small Computer System Interface
LUN
logical unit number
MAC
Media Access Control
Acronyms and abbreviations 54
Download from Www.Somanuals.com. All Manuals Search And Download.
PXE
Preboot Execution Environment
SAN
storage area network
SSH
Secure Shell
VCM
Virtual Connect Manager
WWN
World Wide Name
WWPN
worldwide port name
Acronyms and abbreviations 55
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
H
authorized reseller 53
help command 34
help resources 53
B
I
basic configuration 40
igmp command 19
IGMP settings, configuring 49
interconnect command 19
C
L
configuring LDAP 43
ldap command 20
ldap-group 21
logging out 50
D
M
devicebay command 10
domain command 10
domain setup 41
managed elements 9
E
N
enclosure command 12
enet-network connections, adding to a profile 49
network command 23
O
F
fabric command 16
Fibre Channel setup 46
P
port command 29
profile command 24
properties 7
firmware command 18
Index 56
Download from Www.Somanuals.com. All Manuals Search And Download.
R
remote access 8
S
server command 26
server profile, assigning to a device bay 49
shared uplink port set, creating 45
shared uplink port sets, displaying 46
stackinglink command 28
status command 29
subcommands 9
systemlog command 29
T
technical support 53
U
uplink port properties, modifying 45
uplinkset command 31
user command 32
V
version command 34
Index 57
Download from Www.Somanuals.com. All Manuals Search And Download.
|