Instructions - Parts List
™
308391J
EN
Power-Star
Used to pump high volumes of petroleum and synthetic based oils. For professional use
only.
Model No. 236754, Series A
1:1 Ration Universal Pump and Reciprocator
Model No. 236752, Series A
Reciprocator Only
1500 psi (10 MPa, 103 bar) Maximum Hydraulic Input Pressure
1500 psi (10 MPa, 103 bar) Maximum Fluid Outlet Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
This pump is designed to be used only in pumping
non-corrosive and non-abrasive oils and lubricants.
Any other use of the system can cause unsafe
operating conditions and result in components
rupture, fire, or explosion which can cause serious
injury, including fluid injection.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where
applicable.
WARNING
FIRE AND EXPLOSION HAZARD
When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be
aware that flammable fumes can ignite or explode. To help prevent fire and explosion:
•
•
•
•
•
•
•
Use equipment only in well ventilated area.
Eliminate all ignition sources, such as cigarettes and portable electric lamps.
Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
Ground all equipment in the work area.
Use only grounded hoses.
Stop operation immediately if static sparking occurs or you feel a shock. Do not use equipment
until you identify and correct the problem.
•
Keep a working fire extinguisher in the work area.
SKIN INJECTION HAZARD
High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This
may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical
treatment.
•
•
•
•
Do not point dispensing device at anyone or at any part of the body.
Do not put your hand over the fluid outlet.
Do not stop or deflect leaks with your hand, body, glove, or rag.
Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or
servicing equipment.
•
•
Tighten all fluid connections before operating the equipment.
Check hoses and couplings daily. Replace worn or damaged parts immediately.
308391J
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-
ponent. See Technical Data in all equipment manuals.
•
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
•
•
•
Do not leave the work area while equipment is energized or under pressure.
Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
•
Do not alter or modify equipment. Alterations or modifications may void agency approvals and create
safety hazards.
•
•
•
•
•
•
Make sure all equipment is rated and approved for the environment in which you are using it.
Use equipment only for its intended purpose. Call your distributor for information.
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
Do not kink or over bend hoses or use hoses to pull equipment.
Keep children and animals away from work area.
Comply with all applicable safety regulations.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
•
•
Read MSDSs to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.
MOVING PARTS HAZARD
Moving parts can pinch, cut or amputate fingers and other body parts.
•
•
•
Keep clear of moving parts.
Do not operate equipment with protective guards or covers removed.
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure and disconnect all power sources.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury, including
eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is
not limited to:
•
•
Protective eyewear, and hearing protection.
Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer
4
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Maximum Working Pressure of Accessories
To reduce the risk of serious injury including fluid
injection and splashing in the eyes or on the skin,
which may be caused by component ruptures, all
accessories added to the reciprocator power supply
side of the pump fluid outlet side must have at least a
1500 psi (10 MPa, 103 bar) maximum working
pressure.
The equipment must be grounded to reduce the risk
of static sparking and electric shock. Electric or static
sparking can cause fumes to ignite or explode.
Improper grounding can cause electric shock.
Grounding provides an escape wire for the electric
current.
Pump: Use a ground wire and clamp. Remove the
ground screw (Z) and insert through the eye of the ring
terminal at end of ground wire (Y). Fasten the ground
screw back onto the pump and tighten securely. Con-
nect the other end of the ground wire to a true earth
Pump Accessories
Suction Tube Kit: A suction tube kit is available for
siphoning from 55 gallon containers.
Intake Tube: To install, apply PTFE tape to the female
threads at the top of the tube (Q). Screw the tube tightly
into the intake housing of the stubby pump.
Low-Level Cutoff Valve: To install, screw the low-level
cutoff valve into the bottom of the pump intake tube or
the suction tube. This valve closes the pump intake
when the fluid level is low, causing the pump to stall to
avoid running all day.
Z
Y
NOTICE
A pump outlet drain valve is required in the system.
This valve helps relieve pressure in the
FIG. 1
displacement pump and hose when shutting down
the system and in case of a clogged outlet hose.
Install the valve hose close the pump outlet.
Hydraulic and fluid hoses: Use only electrically con-
ductive hoses.
Hydraulic power supply: Follow manufacturer’s recom-
mendations.
Pump Outlet Drain Valve: Install a drain valve (D) close
to the pump fluid outlet assist in relieving fluid pressure
in the pump, hose, and dispense valve when the pump
is shut off.
Any pails used when flushing: Use only metal,
grounded pails when flushing. Make firm metal-to-metal
contact between the metal part of the dispense valve
and the pail. Use the lowest possible pressure.
Thermal Relief Kit: Install a Thermal Relief Kit (T) at the
pump fluid outlet.
Grounding
308391J
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
N
E
G
J
A
K
L
M
F
R
H
B
C
D
S
T
P
FIG. 2: Typical Installation
Key:
A
B
C
D
E
F
G
H
J
K
L
M
N
Hydraulic Control (See manual 308395)
Porous Plug (weep tube optional)
Fluid Dispense Outlet
Drain Valve (required)
Hydraulic Return Line
Hydraulic Outlet, 1 1/4 npt
Return Line Shutoff Valve
Hydraulic Inlet, 3/4 npt
Hydraulic Supply Line Shutoff Valve
Pressure Gauge
Pressure Reducing Valve
Flow Control Valve
Hydraulic Supply Line (Use only Graco Hydraulic power
supply)
Hydraulic Power Supply
To reduce the risk of damaging the hydraulic power sup-
ply, blow out all hydraulic lines with air, flush thoroughly
with solvent, and then blow out with air again before
connecting the lines to the motor.
Always plug the hydraulic inlets, outlets, and lines when
disconnecting them to avoid introducing dirt and other
contaminants to the system.
P
R
S
T
Dispensed Material Supply Suction Hose Kit
Ground Wire (required)
Wall Mounting Bracket (See manual 308394)
Thermal Relief Kit (required)
Carefully follow the manufacturers recommendations on
reservoir and filter cleaning, and periodic changes of the
hydraulic fluid.
For assistance in designing a system to suit your needs.
Contact your Graco representative.
Mount the pump to suit the type of installation planned.
6
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Pump Isolation: The hydraulic fluid control has ball
Hydraulic Components
valves on the supply and return sides of the manifold.
The ball valves isolate the hydraulic fluid control and
pump for servicing without stopping the hydraulic power
supply.
Always turn off the hydraulic supply side valve (K)
first to avoid possible serious injury or component
Drain Line: Remove the plug (24) from the pump
adapter, and install a 1/8 inch diameter weep tube, end-
ing in a waste container. Monitor the weepage of
hydraulic fluid. If it seems excessive or increases sud-
denly, the reciprocator or pump throat seals may need to
be changed. (FIG. 3)
24
FIG. 3
Hydraulic Fluid Control: The hydraulic fluid control pro-
Pressure Regulation: The hydraulic fluid control reduces
the hydraulic oil pressure to the operating pressure
required for the application.
Flow Regulation: The hydraulic fluid control limits the
maximum amount of oil flow to the motor to keep the
hydraulic motor within the cycle rate limit. This prevents
pump runaway. The limit on the Power-Star is 66 cpm.
308391J
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Pressure Relief Procedure
Before Starting the Pump
Follow the Pressure Relief Procedure whenever
you see this symbol.
Recommended Hydraulic Oil
Use a Graco-approved Hydraulic Oil or a premium, ISO
grade 46 petroleum-based hydraulic oil containing rust
and oxidation inhibitors and anti-wear agents.
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury from
pressurized fluid, such as skin injection, splashing
fluid and moving parts, follow the Pressure Relief
Procedure when you stop spraying and before
cleaning, checking, or servicing the equipment.
Before using any other type of oil in this motor contact
your Graco distributor. Unauthorized use of lesser grad
oil or substitutes may void the warranty.
1. Close the supply line shutoff valve, and then the
return line shutoff valve.
1. Check the hydraulic fluid level in the hydraulic power
supply before each use, and add fluid as necessary
to fill the lines.
2. Open the dispensing valve to relieve the pressure.
2. Flush the pump before using it for the first time to
remove the light oil that was left in after factory test-
ing to protect the pump from corrosion. Be sure the
solvent used is compatible with the fluid to be
pumped and the pump’s wetted parts. See Techni-
from the outlet hose.
3. Place a container under the drain valve to catch any
drainage. Open the pump outlet drain valve.
4. Leave the drain valve open until you are ready to
dispense again.
NOTE: If you suspect that the dispensing valve, exten-
sion, or grease fitting coupler is clogged, or that the
pressure has not been fully relieved after following the
steps above, VERY SLOWLY loosen the coupler or
hose end coupling and relieve pressure gradually, then
loosen completely and clear the clog.
To Start the Pump
1. Turn on the hydraulic power supply.
2. Open the return line shutoff valve (H) first, and
slowly open the hydraulic supply line shutoff valve
3. Adjust the hydraulic inlet pressure from 500 to 1500
psi (3.5 to 10.3 MPa, 35 to 103 bar) with the regula-
tor control adjustment (M) on the hydraulic fluid con-
trol (A). Increasing the inlet pressure increases the
outlet pressure. Decreasing the inlet pressure
decreases the outlet pressure.
4. Always use the lowest pressure possible to obtain
the desired results. This reduces pump wear.
8
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5. Never allow a pump to run dry of the fluid being
pumped. A dry pump quickly speeds up and can
damage itself. If it speeds up, shut off the power
supply to the reciprocator immediately. Refill the
supply container and prime the pump to eliminate
air.
NOTE: To prevent the pump from running dry, use a
low-level cutoff valve.
Shutdown and Care
At the end of the work shift or when the pump is unat-
tended, always relieve the pressure, see Pressure Relief
Procedure on page 8.
Emergency Stop Procedure
Close the supply line shutoff valve marked STOP.
308391J
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
checking or repairing gun.
2. Check all possible problems and causes before dis-
assembling gun.
Problem
Cause
Solution
Closed dispense valve
Pressure too low
Pump only runs with valve open.
Increase supply pressure using the
pressure adjusting valve.
Check hydraulic power supply.
Adjust to a maximum of 12 gpm
(45.4 lpm) flow
Insufficient hydraulic fluid supply
Pump will not run
Clogged fluid outlet line, intake
valve, dispense valve, suction line
Check; clear obstructions.
Press reciprocator reset button (39).
Pump should start immediately. See
Motor stalled
Reciprocator damaged
Check and repair. See Page 11
Pump piston and/or intake valve
worn
Pump speeds up or runs erratically
Refill and reprime. Do not allow
pump to run dry. Monitor closely or
use a low-level cutoff valve.
Empty supply container
Pump piston and/or intake valve
worn
Refill fluid supply container.
Insufficient material fluid supply
Pressure too low
Pump runs, but output low on up
and/or down strokes
Increase supply pressure using the
pressure adjustment on the control.
Clogged fluid outlet line, intake
valve, dispense valve, suction line
Check; clear obstructions.
Repair. See page 11
Excessive weepage from porous
plug (B)
Worn throat seals
Hydraulic oil leaks from seal nuts in Seal nuts (19) are loose, worn, or
Tighten the seal nuts. If leaking per-
sists, change the seal nuts.
the upper housing or cap (36, 43)
damaged
Pump runs slowly with dispense
valve closed
If system is OK, rebuild the pump.
Use kits 220457 and 236862.
Pump/dispense line leakage
10
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
Repair
3. Place the hydraulic motor horizontally in a bench
vise at the pump adapter (42) and bottom cylinder
cap (43).
specified.
4. Remove the displacement pump with a strap
wrench.
5. Remove the cap screws (25) and the mounting plate
(46).
NOTE:
•
Spool valve Repair Kit 220457 is available to
replace the gaskets (29), spring retaining plugs (31),
springs (21), spool (38), trip rod (33) and piston stop
(37). The spool, plugs, and springs must be
replaced as a group.
6. Remove the hydraulic motor from the vise.
7. Place the piston (110) flats in the vise.
8. Loosen, but do not remove the piston rod (44) with a
wrench.
•
•
Clean all parts as you disassemble them, and
inspect for wear or damage. Replace parts as nec-
9. Remove the piston (110) flats from the vise.
®
essary. Use Loctite TL-242 thread sealant, or
10. Place the motor vertically in the vise at the pump
adapter (42) and the bottom cylinder cap (43).
equivalent, when thread sealant is specified.
Pump Repair Kit 236862 is available to replace the
gasket (29), o-rings (11, 12, 105 and 108) seals
(17), packing (107), and piston rings (15).
11. Remove the piston (110), ball (103), and seal (107).
NOTICE
To prevent damage to the spool (38) and the upper
housing (36), remove the detent parts (31, 21, 29, 30,
and 7) before removing the end cap (40).
Disassembly
specified.
NOTE: The socket screw (9), cap screws (22), and
®
retainer (32) are fastened with Loctite TL-242. Heat
may be used sparingly to soften the adhesive during dis-
assembly.
To avoid serious injury, do not move this unit without the
use of lifting equipment. Keep the hoist attached for
steps 1 through 15.
12. Remove one detent assembly retaining plug (31),
spring (21), gasket (29), ball guide (30), and ball (7).
If the ball or other parts stick in the upper housing
(36), use a magnet to extract the parts. Do not allow
the parts to fall into the motor. Repeat the procedure
for the other detent assembly.
the bottom of its stroke.
NOTICE
Avoid getting dust or dirt in the motor during repair.
Cleanliness is essential when repairing a hydraulic
motor.
13. Unscrew the top and bottom flare nuts on the
hydraulic tube (49), and remove the tube. Allow the
oil to drain from the motor into a pan.
14. Remove the socket screws (9), and remove the end
cap (40).
2. Disconnect the displacement pump hoses. Discon-
nect the hydraulic hoses and plug all hydraulic con-
nections and lines to prevent contamination.
15. Remove the bolts (23), but do not remove the rods
(47).
308391J
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
tom cylinder cap (43). Ensure all fluid ports are fac-
ing the same direction.
NOTICE
With the bolts removed, the assembly may separate
at the joints between the cylinder (35) and the upper
housing (36) and bottom cylinder cap (43),
2. Install the piston rod (44) into the pump adapter (42)
and the bottom cylinder cap (43). Lubricate the pis-
ton rings (15) and install the piston rod (44) with the
openings on the rings opposed 180°.
16. Remove the stop plug (39) from the upper housing
(36). Pull the upper housing about 3 inches off the
cylinder (35). Shim the housing with 3/4 in. flat stock
to keep an opening. The cylinder can stay in the
lower housing (43).
3. Only perform steps 4 and 5 if steps 23 and 24 of
Disassembly were performed.
4. Install the compression spring (18) inside the piston
rod. Install the trip rod nut (10) and piston stop (37)
on the trip rod (33).
17. Hold the trip rod (33) steady with a trip rod pliers
(P/N 207579) on the rod, and remove the top hex
nut (16) from the trip rod.
5. Install the trip rod (33) in the piston rod (44). Apply
thread sealant to the retainer (32). With the piston
flat in a vise, tighten the retainer until it is flush or
below the piston surface. This is important to pre-
vent the retainer from backing out during operation
and damaging the motor.
18. Remove the upper housing (36). Remove the valve
spool (38) from the upper housing (36). Save the
spring collars (41), the springs (34), and the parts
remaining inside the upper housing.
19. Inspect the bore in the upper housing (36) and the
outside diameter of the valve spool (38) for wear.
Replace parts if damaged. Inspect the trip rod (33)
above the shoulder for damage. There must be no
reduction in diameter.
6. Install the o-ring (12) on cylinder (35). Install the cyl-
inder over the piston and rings.
7. Install the upper housing (36). Install a 3/4 inch flat
stock shim between the upper housing and the cyl-
inder. Install the trip rod guide (41), the spring (34),
valve spool (38), and the remaining parts from the
inside of the upper housing. See Parts Drawing,
20. Pull the trip rod and piston rod (44) from the lower
housing (43) and cylinder (35).
21. The seals (17) must be replaced if they are leaking.
Remove seals from adapter (42).
8. Holding the trip rod (33) steady with a trip rod pliers
on the rod, and install the top hex nut (16) on the trip
rod.
22. Perform steps 23 and 24 if parts inspected in step
19 are damaged.
9. Replace the o-ring (11) on the stop plug (39). Install
the stop plug in the upper housing (36).
23. Place the piston rod (44) in a vise; tighten the vise
on the flats of the piston rod. Use a spanner wrench
to remove the retainer (32). Remove the trip rod (33)
from the piston rod (44).
10. Install tie rods (47) and bolts (23); hand tighten.
11. Install the two lock nuts (5) and washers (6).
24. Remove the trip rod nut (10) and piston stop (37). If
the piston rod is replaced, remove the compression
springs (18), and compression rings (15) to use the
new piston rod.
12. Apply thread sealant to the socket screws (9). Install
the end cap (40) with the socket screws.
NOTICE
To avoid damaging the internal parts, install detent
parts (31, 21, 29, 30, and 7) after install the end cap
(40).
Reassembly
1. Place the pump adapter (42) in a vise. Grease the
new seal (17) from the repair kit. Install a seal in the
pump adapter (42) with the lip facings down. Install
the rod guide (45) and install the second seal with
the lip facing up in the pump adapter. Install the bot-
13. Install one detent assembly; retaining plug (31),
spring (21), gasket (29), ball guide (30), and ball (7).
Repeat for the other detent assembly.
12
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
14. Align the tie rods (47) and bolts (23) and torque to
70 to 80 ft-lbs (95 to 108 N.m). Install eyelet (26)
Attach hoist to the eyelet.
26
5
9
39
40
11
16
6
4
7
5
6
34
38
30
21
41
29
15. Screw the top and bottom flare nuts on the hydraulic
tube (49), and install the tube.
31
34
36
50
41
5
22
16. Place the motor horizontally in a vise at the pump
adapter (42) and the bottom cylinder cap (43).
17. Apply thread sealant to the threads of the piston
(110) and install the piston, ball (103), and the seal
(107) with the lips facing up.
33
12
35
32
4
47
5
1
37
10
15
12
43
18. Remove the hydraulic motor from the vise.
19. Place the piston (110) flats in a vise.
2
3
17
45
17
20. Tighten the piston rod (44) with a wrench.
21. Remove the piston from the vise.
18
42
46
Rings must be positioned
with joints opposed 180
1
Lips must face
2
3
4
up toward top of motor
Lips must face down to-
ward bottom of pump
22. Place the pump horizontally in the vise.
23. Install the displacement pump with a strap wrench.
24. Remove the hydraulic motor from the bench vise.
Torque to
70–80 ft–lb (95–108 N.m)
Apply Loctite TL–242
thread sealant to threads
25
7
5
6
7
Concave surface faces ball
Torque to
120–130 ft–lb (163–176 N.m)
FIG. 4
25. Unplug all hydraulic connections and lines and con-
nect the hydraulic hoses. Connect the displacement
pump hoses.
Intake Valve
26. Flush the displacement pump if possible. Relieve
the pressure (page 8)
2. Unscrew the valve body (112). Remove the o-ring
(105), ball (104), and retainer (113).
3. Inspect the parts for wear or damage. If the ball is
nicked, replace it. Reassemble, using grease on the
male threads.
308391J
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
Displacement Pump
NOTE: Clean and inspect all parts for wear of damage
as you disassemble them. Replace parts as needed. For
the best results, always replace all the o-rings and pack-
ings when you disassemble the pump.
2. Remove the piston (110). Follow steps 1 through 11
3. Carefully inspect the smooth inner surface of the
cylinder (111) for scoring or irregular surfaces. Such
damage causes premature seal wear and leaking.
Replace the parts as needed.
4. Grease the new piston seal and install with the lips
facing up.
5. Reconnect the reciprocator and displacement pump
as described in steps 16 through 26 of Reassembly,
108
111
107
1
113
104
105
112
FIG. 5
14
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Parts
9
40
32
33
39
11
16
41
34
23
2
37
10
45
38
1
1
15
15
18
34
41
36
24
26
56
29
21
7
17
5
5
6
2
27
30
42
19
46
13
28
31
47
44
50
22
12
54
25
3
49
14
43
See the repair section for important
torque and lubrication notes
35
Rings must be positioned
1
with joints opposed 180
Torque to
2
70–80 ft–lb (95–108 N.m)
19
Torque to
17
4
3
4
5
120–130 ft–lb (163–176 N.m)
Lips face up
12
Lips face down
308391J
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Part No./Description
German (Part No. 290396)
French (Part No. 290397)
Spanish (Part No. 290398)
Ref. Part
Description
Qty.
5
6
7
8
9
100127 NUT, mscr, hex, 5/8-11 unc-2B
100128 LOCKWASHER, spring, 5/8”
101701 BALL, 1/4 inch dia
101754 PLUG, pipe, 3/8 npt(f)
101864 CAPSCREW, soc hd, 5/16-18 x 1
inch
2
4
2
1
3
† Parts included in Pump Repair Kit 236862 (purchase
separately).
10
103450 NUT, hex, self locking, 5/16-18
1
1
2
1
1
11† 104093 O-RING, nitrile rubber
12† 104095 O-RING, nitrile rubber
13
14
104098 TEE, tube, for 3/4 in. (19 mm) tube
104099 ELBOW, 90°, for 3/4 in (19 mm)
tube
15† 104103 RING, piston, compression
16 104105 NUT, hex lock, 1/4-20
17† 104203 SEAL, v-block, polyurethane
2
1
2
1
2
1
2
3
18
19
20
21
22
104664 SPRING, compression
105429 NUT, seal, 3/4-14 npt
105430 NUT, seal, 1 in. npt
108522 SPRING, helical compression
108538 SCREW, soc flat hd, self locking,
1/4-20 x 1/2 in.
23
24
25
26
27
28
109203 BOLT, hex hd
2
1
4
2
1
1
2
2
2
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
110064 PLUG, pipe, vented
112570 SCREW, cap, soc hd
112571 NUT, eye
112573 ADAPTER, pipe, female
112574 UNION, swivel
29† 150111 GASKET, plug
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
54
167210 GUIDE, ball
167431 PLUG, spring retaining
171398 RETAINER
171407 ROD, trip
171411 SPRING, compression
171412 CYLINDER
172814 HOUSING, upper
181243 STOP, piston
181874 SPOOL, valve
183252 PLUG, stop
183290 CAP, end
183659 GUIDE, trip, shaft
189714 ADAPTER, pump
189715 CAP, cylinder, bottom
189716 PISTON, rod, hydraulic
189717 GUIDE, rod
189718 PLATE, mounting
189719 ROD, tie
189720 LABEL, identification
210108 TUBE
210292 BEARING and GUIDE
116343 SCREW, ground
56▲ 290331 LABEL, instruction, English
▲ Replacement Danger and Warning labels, tags, and
cards are available at no cost. Also available in the
following languages:
16
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref. Part
Description
Qty.
Ref. Part
Description
Qty.
110 189707 PISTON, fluid
111 189708 CYLINDER, pump
112 189709 VALVE, housing
113 189710 RETAINER, ball
114 189711 WASHER, piston
1
1
1
1
1
101 236752 RECIPROCATOR, hydra,
Power-Star
103 101178 BALL, metallic
104 108001 BALL, metallic, sst
105† 110828 PACKING, o-ring
107† 112565 SEAL, block vee
108† 166071 PACKING, o-ring
1
1
1
1
1
1
† Parts included in Pump Repair Kit 236862 (purchase
separately).
114
107
103
110
108
101
111
105
03845
113
104
112
308391J
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
.
™
Power-Star
US
Metric
Fluid Ratio
1:1
45.4 lpm
10.3 MPa, 103 bar
45.4 lpm
Maximum Output Flow
Maximum Output Pressure
Maximum Input Flow
12.0 gpm
1500 psi
12.0 gpm
1500 psi
130°F
Maximum Hydraulic Fluid Input Pressure
Maximum Input Fluid Temperature
Pressure Reducing Adjustment Range
Weight
10.3 MPa, 103 bar
55°C
300-1500 psi
100lb
2.07 - 10.3 MPa, 20.7 - 103 bar
45.4 kg
Rod Seals
Nitrile
Polyurethane
Piston Seals
Displacement Pump Wetted Parts
Sound Pressure
Iron, Steel, SST Nitrile, Polyurethane
78 dB(A)*
* Sound pressure reading taken with pump operating at 60 cycles per minute. Sound pressure measured per
CAGI-PNEUROP, 1971
Loctite® is a registered trademark of the Loctite Corporation.
Dimensions
8.0 in.
(203.2 mm)
7.0 in.
(177.8 mm)
4.0 in.
(101.6 mm)
30 in.
(762 mm)
.406 in. ( 10.31 mm) diameter (4);
for 3/8 in. screw
18
308391J
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Performance Chart
308391J
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308391
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 1994, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised February 2014
Download from Www.Somanuals.com. All Manuals Search And Download.
|