GILSJN MIXERS
5 1/2 CU. FT.
CONCRETE MIXER
MODEL: 59015C
OPERATOR’S GUIDE & PARTS MANUAL
GILSJN MIXERS
4343 Easton Road · St. Joseph, MO 64503
BY
816-233-4840 · 800-253-3676
Fax 816-233-4624 · 888-253-3676
E-Mail: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
1-SAFETY PRECAUTIONS
THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP
PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST
OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING
CERTAIN PRECAUTIONS. READ AND TAKE THE FOLLOWING
PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP
PREVENT ACCIDENTS. EQUIPMENT SHOULD BE OPERATED ONLY BY
THOSE WHO ARE RESPONSIBLE AND INSTRUCTED TO DO SO.
§
§
Read all mixer and electric motor/engine instructions before operation.
Use a grounded, three wire plug-in for all mixers using an electric motor or an
electric starting engine.
§
§
Do not use mixer in standing water if powered by an electric motor or an electric
starting engine.
Do not over-fill the mixer. There should not be any liquid running out of the mixer
drum.
§
§
§
§
Know how to stop the motor/engine instantly.
Keep hands and feet away from all moving parts.
If you are unfamiliar with the mixer, test run the empty mixer prior to actual use.
Never charge or fill unit prior to starting, as the over-load initially encountered could
damage the motor/engine.
§
Stop motor/engine whenever you leave or clean the unit. Disconnect power cord on
electric motor.
§
§
Never operate mixer without guards being properly positioned and secure.
Avoid spilling gasoline. Never fill tank while the engine is running or while you are
smoking.
§
§
Open doors if engine is running in an enclosed area. Exhaust fumes are dangerous.
Store gasoline in safe container. Store the container in a cool, dry place. Do not
keep in the house or near heating appliances.
§
§
Never reach into drum while mixer is running.
Keep mixer in good operating condition. Loose or damaged parts are dangerous and
should be tightened or replaced before operating.
§
Keep bystanders, especially children, away from mixer while operating.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
2-OPERATION
DRUM SPEED
The mixer drum should revolve between 20 and 25 R.P.M.’s for best results in
mixing concrete. To obtain this speed using a 1725/1800 R.P.M. electric motor, use a
2” diameter “A” section V-pulley.
If using a 6 to 1 speed reduction 3 H.P. gasoline engine, use a 6 ¼” diameter “A”
section V-pulley.
GETTING READY FOR MIXING
Lay out forms for your concrete floor, patio, driveway, sidewalk, etc.
The quality of concrete is directly related to the quality of the cement paste. The
quality of the paste, in turn, is directly related to the amount of water mixed with the
cement. For a given amount of cement, as the amount of mixing water is reduced, the
strength of the paste increases, making the concrete stronger and more durable.
The proportions by weight given in Table 1 can be used as a starting point to make 1
cu. Ft. (0.028 m3) of strong, durable concrete. The proportions given in Table 2 are
volumetric; 1 bag of cement is equal to 1 cu. ft. (0.28 m3) and weighs 94 lbs.
(42.6 kg). The Canadian bag of cement has a net mass of 40 kg.
The proportions are only a guide and may need adjustments to give a workable mix
with locally available aggregates.
Table 1. Proportions by Weight to Make 1 Cu. Ft. of Concrete
Air-entrained concrete
Course
Concrete without air
Course
Maximum-
size course
aggregate in.
Cement
lb
Sand
lb
aggregate Water
Cement
lb
Sand
lb
aggregate Water
lb
lb
lb
lb
3/8
1/2
3/4
1
29
27
25
24
23
53
46
42
39
38
46
55
65
70
75
10
10
10
9
29
27
25
24
23
59
53
47
45
43
46
55
65
70
75
11
11
10
10
9
1 1/2
9
*If crushed stone is used, decrease coarse aggregate by 3 lbs and increase sand by 3 lbs.
Metric conversion: 1 lb = 0.121 kg
10 lbs = 4.54 kg
1 in. = 25mm
1 Cu. Ft. = 0.028 m 3
Table 2. Proportions by Volume*
Maximum-
Air-entrained concrete
Concrete without air
Course
Course
size course
aggregate in.
Cement
lb
Sand
lb
aggregate Water
Cement
lb
Sand
lb
aggregate Water
lb
lb
lb
lb
3/8
1/2
3/4
1
1
1
1
1
1
2 1/4
2 1/4
2 1/4
2 1/4
2 1/4
1 1/2
2
2 1/2
2 3/4
3
1/2
1/2
1/2
1/2
1/2
1
1
1
1
1
2 1/2
2 1/2
2 1/2
2 1/2
2 1/2
1 1/2
2
2 1/2
2 3/4
3
1/2
1/2
1/2
1/2
1/2
1 1/2
*The combined volume is approximately 2/3 of the sum of the original bulk volumes.
ã Portland Cement Association 1980
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING THE MIXER
Start the mixer. Refer to motor/engine instructions. After drum has started rotating, pour
about half of the water in the drum.
NOTE: The drum my leak slightly when first used. This will stop after a few batches.
Add aggregate (gravel) first then cement and last sand.
UNLOADING THE MIXER
Refer to Fig. 1
Allow the entire mixture to mix for one full minute. Do not stop mixer from rotating.
Hold the tilt handle and unlock the stop lever. Dump concrete to either side by tilting the tilt
handle in the direction required. Before reloading the mixer, slowly pour a pail of water over
the lip of the drum, permitting water to clean the inside of drum. When cleaned, dump water.
Now you are ready for your next batch.
CLEANING THE MIXER
After each run of concrete has been poured, do the following:
With the drum rotating, spray water into drum permitting the water to run down the inside
and outside of drum. Add one shovel full of coarse aggregate and permit this mixture to
scour the inside of drum for about two minutes.
This practice will help keep the drum clean, which is essential in obtaining the best mixing
result. Never permit concrete to harden on either the inside or outside of drum.
EXTENSION CORDS-ELECTRIC MOTOR
The following size extension cords should be used for this mixer: length of cord, up to 100 ft-
14 gauge wire; up to 200 ft-12 gauge wire; up to 300 ft – 10 gauge wire; up to 400 ft – 8
gauge wire.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3-LUBRICATION & STORAGE
Each day before operating, lubricate at the following points:
Engine/Motor – Refer to engine/motor operating instructions for all maintenance and
lubrication instructions and requirements.
GREASE FITTINGS: Refer to Fig. 2
Clean off grease fitting before greasing. Use pressure type grease gun. Grease lightly
with general purpose grease (2 to 3 pumps).
§ Drum Shaft Bearings (where used)
§ Drive shaft Bearings
§ Tilt Wheel Shaft Bearings (where used)
§ Brake Lever Shaft (where used)
OIL:
Refer to Fig. 2
Use SAE 30 engine oil.
§ Yoke Tilt Mechanism
STORAGE
For short term storage, clean the mixer and store in a dry place. If the mixer is not to
be used for an extended period of time, service mixer completely and store it in a dry
place.
1. Refer to motor/engine instructions for storage instructions.
2. Cover exposed metal surfaces with a thin coat of SAE 30 engine oil.
3. Lubricate per instructions under LUBRICATION & STORAGE section.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4-REPLACEMENT DECALS
#217728: Decal, Safety Instructions
#5706: Decal, Gilson Name Plate
#38257: Decal, Drum Rotation
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONCRETE MIXER PARTS LIST
ITEM NO. PART NO. DESCRIPTION
QTY.
1
2
1102
1183
Grease Fitting
Grip
1
1
3
19866 Bearing Cap
1
4
5
6
7
8
9
19902 Drum Assembly
19911 Blade Assembly
19913 Paddle Assembly
19914 Drum Shaft Assembly
214858 Belt Guard Cover
214907 Belt Guard Assembly
245948 Frame Assembly
245949 Yoke Assembly
245952 Tilt Handle
245956 Bushing Spacer
245977 Yoke Lock Tube
245978 Yoke Lock Assembly
245980 Pivot Tube
1
2
2
1
1
1
1
1
1
2
1
1
2
1
2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
37
35
36
37
38
39
40
41
42
43
44
45
46
47
29209 Pulley
4959
5450
5452
5498
5523
5904
Bushing
Drum Shaft Spacer (Light)
Drum Shaft Spacer (Heavy)
Ring Gear
AS REQ'D
AS REQ'D
1
2
1
1
1
1
8
4
1
5
2
5
2
5
2
20
2
2
5
5
2
7
2
1
2
2
1
Skid
Grease Fitting (Drum)
763-40033 Drum Shaft Bearing
6007
6008
Pinion Gear
Drive Shaft
70448 Bolt, Carriage 3/8-16 x 3/4
70456 Bolt, Carriage 3/8-16 x 1 3/4
70073 Set Screw, Square Hd. 1/2-13 x 1
70090 Cap Screw, Hex Hd. 1/4-20 x 1/2 Plated
*
Cap Screw, Hex Hd. 5/16-18 x 1 Plated
70249 Cap Screw, Hex Hd. 3/8-16 x 1 1/2
70343 Cap Screw, Hex Hd. 1/2-13 x 1 1/2
*
Nut, Hex 1/4-20 Plated
70549 Nut, Hex 5/16-18 Plated
*
*
Nut, Hex 3/8-16
Nut, Hex 1/2-13
70701 Washer,Flat 5/16 Plated
70703 Washer,Flat 3/8
*
*
*
*
Washer,Spring Lock 1/4 Plated
Washer,Spring Lock 5/16 Plated
Washer,Spring Lock 3/8
Washer,Spring Lock 1/2
71017 Roll Pin 7/32 x 1 1/2
5269
*
Drum Shaft Bushing
Bolt,Hex Hd. 3/8-16 x 3 1/4
760-40043 Pulley Spacer
*Common Hardware May Be Purchased Locally.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MIXERS ONE-YEAR WARRANTY
This product is warranted to the original purchaser only, to be free of defects in
material and workmanship under normal use, for one year from purchase date.
Cleform Tool Corp. shall without charge for parts and labor, repair or replace such
parts which are found to be defective. All transportation charges for replacement
parts must be borne by the purchaser.
For warranty service, the product must be delivered, with proof of purchase date, to
the dealer of original purchase, or any factory authorized service dealer. The delivery
of the unit must be made no later than 30 days after the expiration of the warranty
period.
If difficulty is encountered in having warranty work performed, contact the factory
Service Department:
CLEFORM TOOL CORP.
4343 EASTON ROAD
ST. JOSEPH, MO 64503
800-253-3676 PHONE
888-253-3676 FAX
Exclusion from this warranty:
1. The following items are not covered under the CLEFORM TOOL CORP. One
year Warranty and are warranted by their respective manufacturer.
a) Engines, including starters, generators, alternators and gear reducers.
b) Enclosed gear transmissions.
(Note: A copy of the warranty and service contact information for the
above items is furnished with the individual product).
2. All consequential damages, including pickup and delivery of the unit,
communication, mileage charges and/or rental of a replacement unit during
repairs are not covered under this warranty, nor is any loss of income and/or other
loss resulting from the failure of the product to function due to a warranty defect.
3. This warranty will not apply when the product becomes inoperative due to
misuse, normal wear, neglect, improper maintenance, accident or freight damage;
has not been operated and maintained in accordance with the instructions
furnished in the Operator’s Manual; or has been altered or modified without
approval from the factory Service Department.
4. No parts or products are to be returned to the factory without prior written
approval from the factory.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ALL IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR
FROM DATE OF PURCHASE BY THE ORIGINAL RETAIL CUSTOMER AND
TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED
WARRANTIES ARE EXCLUDED AND DISCLAIMED AFTER THE
EXPIRATION OF SUCH PERIOD.
Some states do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitations of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
HOW TO OBTAIN PARTS AND
SERVICE INFORMATION
For parts and service information,contact either
your local dealer or the Cleform Tool Corp. factory:
CLEFORM TOOL CORP.
4343 EASTON ROAD
ST. JOSEPH, MO 64503
800-253-3676 PHONE
888-253-3676 FAX
HOW TO ORDER PARTS
When ordering parts be sure to indicate the
following information:
§
§
§
§
§
Name of each part
Complete part number
Quantity of each part
Model Name (Include all letters and numbers)
Serial Number (Include all letters and numbers)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|