Triplex Ceramic
Plunger Pump
Model Manual
MODEL
GIANT INDUSTRIES LIMITED WARRANTY
GP8155-R
Giant Industries, Inc. pumps and accessories are warranted by the manufacturer to be free from defects in
workmanship and material as follows:
WITH INTEGRAL GEARBOX 180o REVERSE
1. For portable pressure washers and self-service car wash applications, the discharge manifolds will never
fail, period. If they ever fail, we will replace them free of charge. Our other pump parts, used in portable
pressure washers and in car wash applications, are warranted for five years from the dateof shipment for
all pumps used in NON-SALINE, clean water applications.
2. One (1) year from the date of shipment for all other Giant industrial and consumer pumps.
3. Six (6) months from the date of shipment for all rebuilt pumps.
4. Ninety (90) days from the date of shipment for all Giant accessories.
This warranty is limited to repair or replacement of pumps and accessories of which the manufacturer’s evaluation
shows were defective at the time of shipment by the manufacturer. The following items are NOT covered or will
void the warranty:
1. Defects caused by negligence or fault of the buyer or third party.
2. Normal wear and tear to standard wear parts.
3. Use of repair parts other than those manufactured or authorized by Giant.
4. Improper use of the product as a component part.
5. Changes or modifications made by the customer or third party.
6. The operation of pumps and or accessories exceeding the specifications set forth in the Operations
Manuals provided by Giant Industries, Inc.
Liability under this warranty is on all non-wear parts and limited to the replacement or repair of those products
returned freight prepaid to Giant Industries which are deemed to be defective due to workmanship or failure of
material. A Returned Goods Authorization (R.G.A.) number and completed warranty evaluation form is required prior
to the return to Giant Industries of all products under warranty consideration. Call (419)-531-4600 or fax (419)-531-
6836 to obtain an R.G.A. number.
Repair or replacement of defective products as provided is the sole and exclusive remedy provided hereunder and
the MANUFACTURER SHALL NOT BE LIABLE FOR FURTHER LOSS, DAMAGES, OR EXPENSES, INCLUDING
INCIDENTALANDCONSEQUENTIALDAMAGESDIRECTLYORINDIRECTLYARISINGFROMTHESALEORUSE
OF THIS PRODUCT.
THELIMITEDWARRANTYSETFORTHHEREINISINLIEUOFALLOTHERWARRANTIESORREPRESENTATION,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OR MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE AND ALL SUCH WARRANTIES ARE HEREBY DISCLAIMED AND
EXCLUDED BY THE MANUFACTURER.
Contents:
GIANT INDUSTRIES, INC.
900 N. Westwood Ave.
Toledo, Ohio 43607
(419) 531-4600
FAX (419) 531-6836
Installation Instructions:
Pump Specifications:
Exploded View/Parts List:
Repair Kits/Tool List:/Torque Specifications
Troubleshooting Chart:
Repair Instructions:
page 2
page 3
pages 4-5
page 6
page 6
pages 7-10
page 11
back page
Dimensions:
WarrantyInformation
4/08 GP8155-R.PMD
Updated 4/08
Copyright 2008 Giant Industries, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
GP8155-R PUMP REPAIR INSTRUCTIONS
Specifications
Model GP8155-R
U.S.
15) Replace seal retainer (33), seal (32) and clip ring (33B). Seal (32) must always be installed
so the seal lip on the inside diameter faces the oil. Possible axial float of the seal retainer (33)
to be compensated with shims (33C). Re-assemble the seal sleeves (39) and plunger pipes
(36B). Tighten the tension screw (36C) to 30 Ft-lbs. Replace valve casing and tighten hexagon
(Metric)
Volume ............................................................. Up to 74.8 GPM ...... (283 LPM)
Discharge Pressure .........................................Up to 2900 PSI ........ (200 bar)
Speed ...............................................................Up to 580 RPM ....... 580 RPM
Inlet Pressure...................................................Up to 29 PSI............ (2.0 bar)
Plunger Diameter............................................. 2.17” ........................ 55mm
Plunger Stroke ................................................. 2.83” ........................ 72mm
Crankshaft Diameter .......................................2.76” ........................ 70mm
Key Width ........................................................ 0.55” ........................ 14mm
Crankshaft Mounting ......................................................................... Either side
Shaft Rotation .................................................................................... Top of pulley
........................................................................................................... Towards manifold
16) Mount cooling plate (K1) and gear cover (K3) with their respective seals (K2). When assembling
the cooling circuit line, make sure that the oil cooler connection (K7) is always joined to the
upper connection (K3) of the gear cover.
Heat ball bearings (74 and 75) first before pressing them on to the pinion. Press the cogwheel
slightly on to the crankshaft so that the pinion (69) together with the ebaring (74) can be inserted.
Move the pinion (69) against the cogwheel and make them mate perfectly when mounting. Then
carefully tap the cogwheel and the pinion simultaneously on to the crankshaft and into the bearing
seat. Fit fitting disc (69) and secure screw (72) with Loctite. Fit the seal (76) on to the cylindrical
pins (68).
o
Temperature of Pumped Fluids........................ Up to 86 oF .............. (30 C)
Inlet Ports .......................................................................................... (2) 3" BSP
Discharge Ports ................................................................................. (2) 1-1/4" BSP
Weight .............................................................. 794 lbs. .................... (360kg)
Crankcase Oil Capacity ................................... 3.7 Gal. .................... (14.0 liters)
Fluid End Material............................................ Nickle plated Spheroidical Cast Iron
Push the gear cover (66) carefully onto the bearing (75). Make sure that the radial shaft seal (73)
does not get damaged during fitting onto the pinion.
Before putting into operation again, turn the reduction gear shaft by hand at least
four full turns to make sure the gear is correctly aligned.
Consult the factory for special requirements that must be met if the pump is to
operate beyond one or more of the limits specified above.
HORSEPOWER RATINGS:
GP8155-R HORSEPOWER
The rating shown are the power
requirements for the pump. Gas
engine power outputs must be
RPM GPM 500 PSI 1000 PSI 2000 PSI 3000 PSI
approximately twice the pump
REQUIREMENTS
300 38.7
400 51.6
500 64.5
580 74.8
13.3
17.8
22.2
25.8
26.7
35.6
44.5
51.6
53.4
71.2
89.0
80.1
106.8
133.4
154.8
power requirements shown above.
We recommend a 1.15 service
factor be specified when selecting
an electric motor as the power
source. To compute specific pump
horsepower requirements, use the
following formula:
103.2
SPECIAL NOTE:
The theoretical gallons per revolution (gal/rev) is 0.129.
To find specific outputs at various RPM, use the formula:
GPM X PSI
= HP
1450
GPM = 0.129 x RPM
10
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GP8155-R PUMP REPAIR INSTRUCTIONS
EXPLODED VIEW - GP8155-R
To Dismantle Crankcase Gear
11) Take out plungers and seal sleeves as described
above. Drain the oil by taking off the plug (12). After
removing the clip ring (33B), lever out the seal retainer
(33) and seal (32) with a screwdriver. Open hose
adapter (K11) and remove gear cover (K3) by removing
the socket head cap screws (K5). Remove the cooling
vane plate (K1) by removing the screws (K4)
12) Remove the connecting rod screws (24).
Connecting rods are marked 1 to 3
for identification. Do not rotate connecting rod
halves or interchange them. When re-assembling,
the connecting rod must be fitted in their exact
original position on the crankshaft journals.
14) Reassemble in reverse order. Replace the
connecting rod and crosshead exactly as they
were removed. Press the bearing ring (21) past
the clip ring groove. Replace the shims (21C).
Snap in the clip ring (19) and insert crankshaft
from other side, then press in the roller bearing
(20). Mount bearing cover (14) and tighten screws
(17) to 64 Ft-lbs. Adjust axial play (clearance) on
the crankshaft to minimum 0.1mm / 0.15mm
using shims (21A/B). Connecting rods must sit
exactly in the middle of the crankshaft journal.
Mount connecting rod halves in the exact, original
position and tighten to 37 Ft-lbs. The shaft should
turn easily.
13) Push connecting rod halves together with the
crosshead as far as possible into the crosshead
guide. Remove bearing cover (14). Begin dismantling
of the reduction gear by removing screws (67). Press
off gear cover (66) by screwing two screws into both
threaded bores. Remove screw (72) and take off fitting
disc (69). Remove cogwheel from shaft with a removal
tool and take the crankshaft out of the crankcase by
gently tapping it with a rubber mallet. Remove connect-
ing rod (24) and crosshead (25) from crankcase.
Remember that this assembly must be re-assembled
exactly as it was removed. Check surfaces on connect-
ing rods (24), crankshaft (22) and crosshead (25).
Check the surfaces of the crosshead guides in the
crankcase for any uneveness.
Connecting rods must be able to
move slightly sideways on the stroke journals.
9
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GP8155-R PUMP REPAIR INSTRUCTIONS
Parts List - GP8155-R
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
18
19
20
21
21A
21B
21C
22
23
24
Part
Description
Crankcase
Qty
Item
Part
Description
Qty
05410
06893
05411
05412
05413
05414
05381
05035
01009
05415
07102
06273
22929
05036
05037
05038
05039
05124
05416
05417
05042
05043
05113
05418
05419
05047
05048
05049
05051
07408
05420
05421
05422
05052
1
1
2
2
4
4
1
1
1
1
1
3
4
1
1
8
8
1
1
1
3
3
3
1
1
3
3
3
6
2
2
2
1
1
5
5
9
1
4
3
3
3
3
3
3
3
3
3
3
3
6
6
3
3
3
3
9
3
3
8
8
1
50A
50B
51
51A
51B
51C
51D
51E
51F
52
52A
52B
52C
52D
52E
52F
56
56A
57
57A
58
59
59A
60
13162
05075
05076
05077
05078
05079
07658
05080
05081
05082
05077
05084
05079
06258
05080
05081
05085
06258
05086
Centering Stud
Discharge Casing
Suction Valve Assy.
Spring Tension Cap
Suction Valve Seat
Valve Plate
2
1
3
3
3
3
3
3
3
3
3
3
3
6
3
3
3
3
3
3
12
2
2
1
1
6
6
1
10
10
4
1
Oil Filler Plug Assy with Vent
Rear Foot for Crankcase
Front Foot for Crankcase
Hexagon Socket Screw
Hexagon Socket Screw
Plug 3/8 for Oil Dipstick
Oil Dipstick Assy
O-Ring
O-Ring
Valve Spring
Valve Spring Guide
Discharge Valve Assy
Spring Tension Cap
Discharge Valve Seat
Valve Plate
O-Ring
Valve Spring
Valve Spring Guide
Discharge ValveAdaptor
O-Ring
Plug M33*1.5
O-Ring
Plug G3/8
Copper Washer
8) Take out the seal case (38) from the valve casing
7)
Be careful not to damage the seal
(50) and check o-rings (38A) (if necessary secure
two screwdrivers in the front o-ring groove to extract
seal casing from valve casing). Coat seals with
silicon grease before installing.
sleeve (39) and pressure ring (41). Check the inner
diameter of the pressure ring for wear and if neces-
sary replace together with seals (40) and (42). Clean
all parts. New parts should be lightly coated with
silicon grease before installation. Insert the seal unit
(40, 41, 42 43) into the sleeve. Push the ceramic
plunger carefully through the seals from the crank-
case side. If necessary, the seals can be held tightly
using a suitable pipe support held on the other side of
the seal sleeve.
Bearing Cover Closed
O-Ring
Hexagon Socket Screw M12
Spring Ring
Mounting surfaces of the crankcase
and the valve casing must be clean and free of
damage. The components must lie exactly and
evenly on one another. The same exactness applies
for all centering positions in the crankcase, pres-
sure and valve casing.
Clip Ring
Tapered Roller Bearing
Tapered Roller Bearing
Fitting Disc
Pressure Spring
07210-0100 Pressure Spring
Hexagon Socket Screw
Fitting Disc
Fitting Disc
05087
07109
06272
06909
05088
05302
06934
05423
05424
07274
05425
05426
07614
05427
05428
05429
05430
05431
05432
05433
05025
07662
07544
05434
05026
05027
05028
05029
07381
08041
05030
06272
07109
05120
05032
05033
05402
05435
05404
05436
Plug G1/2
Copper Seal
Plug G1 1/4
Plug G3
Plug G1/4
Copper Gasket
Gear Cover
Hexagon Screw
Washer
Cylinder Pin
Crankshaft For Turned Gear
Fitting Key
Conn-rod Assy
61
62
62A
66
67
67A
68
69
25
28
29
Crosshead c/w Plunger
Crosshead Pin
Hexagon Screw
Hexagon Nut
29A
29B
29C
29D
30
30A
30B
30C
30D
31
Bracket 2 for Cooling Hose
Support Clamp
Bracket 1 for Cooling Hose
Cover Plate
Gear Wheel Set (2200 RPM=3.8)
Fitting Key
70
1
07225-0100 Hexagon Screw
72
Hexagon Screw
Shaft Seal Ring for Gear
Roller Bearing
Roller Bearing
Fitting Disc
Gear Seal
Flange c/w Gear
Oil Cooler
Mounting Aid for Valve
Hexagon Socket Screw M8
Hexagon Socket Screw
Cooling Vane Plate
Seal for Gear Cover
Gear Cover
Hexagon Hd Cntrsnk Screw
Hexagon Socket Screw
Washer
Connection for Oil Cooler
Copper Seal
Plug G1/2
Connecting Branch
U-Joint Connector c/w Nut
Tube for Cooler
Hose Clamp
1
1
1
1
1
2
1
1
1
1
9
1
2
1
8
8
8
1
6
2
3
3
2
4
2
1
4
13136
08280
05050
07623
05058
05055
05056
05054
05059
05060
05280
05062
07665
06900
05283
13286
05281
05275
05066
07723
05276
05277
05278
05279
05072
05073
05074
Grommet
Washer
73
74
75
75A
76
77
78
79
80
Splash Cover
Eye Bolt
Radial Shaft Seal
Seal Retainer
O-Ring
Clip Ring
Fitting Disc
Oil Shield
Plunger Pipe
Tension Screw
Copper Washer
Centering Sleeve
Seal Case
O-Ring
Support Ring
Seal Sleeve
32
33
33A
33B
33C
34
36B
36C
36D
36E
38
38A
38B
39
39A
40
41
42
43
45
49
49A
50
9) Coat the seal sleeve(39) lightly with anti-corrosive
grease (e.g. molycote no.Cu-7439) in its fitted area
towards the crankcase. Insert the seal sleeves in to
their crankcase fittings. Coat the threads of the
tension screw (36C) lightly with thread glue and
insert it together with a new copper ring (36D)
through the ceramic pipe. Turn the pump by hand
until the plunger (25) rests against the plunger pipe.
Tighten the tension screw at 30 Ft-lbs.
Replacing Valve Casing:
10) Put seal cases (38) in the centering holes of the
valve casing, then push valve casing carefully on to
centering studs (50A). Tighten hexagon screws (49A)
evenly and crosswise at 266 Ft.-lbs.
81
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
K11
K12
K13
K14
K15
K16
The torque tension on the screws (49A)
must be checked after 8-10 operating hours; the pump
must be at zero pressure. Thereafter, the tension is
to be checked every 200 operating hours.
Thread glue must never come between
the plunger pipe (36B) and centering sleeve (36E).
Overtensioning of the plunger pipe by excessive
tightening of the tension screw and/or dirt or damage
on the mounting surfaces can lead to plunger pipe
breakage. Insert the seal tension spring (45) and o-
ring (39A) in to the seal sleeve (39).
O-Ring
Compact Ring
Pressure Ring
Sleeve
Sleeve Support Ring
Seal Tension Spring
Stud Bolt
Hose Guard
Hose Coupling Nut
Flat Gasket
Hexagon Nut
Valve Casing
8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GP8155-R PUMP REPAIR INSTRUCTIONS
GP8155-R PUMP REPAIR KITS
Valve Inspection and Repair
Inlet Valve Kit - #09587
Plunger Packing Kit #09616
Item
51B
51C
51D
51E
51F
56A
Part #
05078
05079
07658
05080
05081
06258
Description
Inlet Valve Seat
Valve Plate
O-Ring
Qty.
1
1
1
1
Item
38A
39A
40
Part #
13286
05066
07723
05277
Description
O-Ring
O-Ring
Seal Ring
V-Sleeve
Qty.
6
6
3
9
Valve Spring
Valve Spring Guide
O-Ring
42
1
3
Discharge Valve Kit - #09588
Oil Seal Kit - #09584
Item
52B
52C
Part # Description
Qty.
1
1
Item
32
Part #
05058
05056
Description
Radial Shaft Seal
O-Ring
Qty.
3
3
05084 Discharge Valve Seat
05079 Valve Plate
3) Take out pressure springs
(57A). Pull out assembled
valves (51 & 52) with valve puller.
2) Lift discharge casing
(50B) up and away.
1) Remove socket head cap
screws (58)
33A
52D/56A 06258
O-Ring
2
52E
52F
05080 Valve Spring
05081 Valve Spring Guide
1
1
GP8155-R TOOL LIST AND TORQUE SPECIFICATIONS
Item Part #
17 05038
24 05047
33B 05054
36C 05062
49A 05073
Description
Hexagon Socket Screw
Connecting Rod Hex. Hd. Socket Screw 37(50)
Torque Ft-Lbs (NM)
64(87)
Tool Needed
4) Remove valve assembly (52) from discharge valve adapter (56) by gently twisting apart. The spring tension
cap (51A, 52A) is screwed together with the valve seat (51B or 52B). Screw off spring tension cap. Takeout
springs (51E, 52E) and valve plate (51C, 52C). Check sealing surfaces and O-rings (51D, 52D). Replace worn
parts. Coat threads of valve seat with silicon grease or molycote anti-seize Cu-7439 when reassembling.
Before refitting the valves, clean the sealing surfaces in the casing and check for any damage. Coat o-rings
(51D, 52D & 56A) with silicone grease to help with re-assembly. Replace valve assembly (51) and pressure
spring (57). Assemble valve assembly (52) to discharge valve adapter (56) by tapping together lightly with
rubber mallet. While replacing the valve assemblies use a rubber mallet to tap the top of the valve puller lightly.
This insures proper seating. Replace pressure spring (57A) and the discharge casing (50B). Tighten caps (58)
at 133 Ft-lbs; check torque tension after 8-10 operating hours.
10mmAllen Wrench
8mmAllen Wrench
Industrial Snap Ring Pliers
16mm Socket
30mm Socket
Valve Puller (p/n 07662) Included
w/pump
Clip Ring
N/A
Tension Screw
Hexagon Nut (Manifold)
30(40)
265 (360)
N/A
51-52 05076-05082 ValveAssemblies
58 05087
K5 07381
Hexagon Socket Screw
Hexagon Socket Screw
132 (180)
N/A
12mmAllen Wrench
8mmAllen Wrench
GP8155-R TROUBLESHOOTING
Problem
Pressure Drops, water leaks
Cause
V-sleeves leak
Solution
Replace V-sleeves, check surface of
plunger
To Check Seals and Plunger Pipe
Pressure drops, pump gets loud Discharge or suction valve leaks
Steam formation (Cavitation)
Replace valve(s)
Reduce suction height, reduce flow
resistance in inlet line, clean inlet
filter, lower water temperature.
Examine valves
Irregular pressure
Worn Valves
O-ring on valves or inlet valve
adapter leaks
Examine O-rings, check valve
casing for unevenness on the
sealing surfaces
Oil leaks at visible part of plunger Gear sealing is leaking
Examine seals and running surface
of plunger
5) Remove hexagon nuts (49A) and valve
6) Remove tension screw (36C) and take
Dirty, milk-colored or frothy oil
Oil leakage on the crankshaft
Water has mixed with oil
Shaft seal ring leaks
Replace oil immediately, find & fix
the cause
Check seal and shaft
Dismantle gear, examine all parts,
replace worn parts, check oil level. If
service life was too short, check for
excess strain or whether lubrication
intervals were too long. Only
specified lubricants are to be used.
casing together with seal case (38) from
seal sleeve (39) together with all mounted
crankcase (1). If necessary, carefully tap the
parts out of the drive. Pull plunger pipe (36B)
valve casing (50) past the centering stud (50A)
out of the seal assembly and check for any
Noise increases without the loss Worn bearing
using a rubber hammer.
IMPORTANT! If necessary, support the valve
casing by resting it on wooden blocks or by
using a pulley.
damage. Carefully, remove seal rings (40) and
sleeves (42) with a screwdriver.
7
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|