Fisher Price Swing Sets BO639 User Manual

Cr a dle Swing  
Cradle  
(Seat moves side to side)  
Swing  
(Seat moves front to back)  
Model Number: B0639  
Please keep this instruction sheet for future reference, as it contains important information.  
Adult assembly is required.  
Tools needed for assembly: Phillips Screwdriver and Adjustable Wrench (both not included).  
Requires fourD(LR20) alkaline batteries for operation (not included).  
Maximum Weight Limit: 24 lbs. (10.9 kg.)  
IMPORTANT! If your child weighs less than 24 lbs., but is really active and appears to be  
able to climb out of the swing, immediately discontinue its use.  
Product features and decorations may be different than shown in photos above.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pa r ts  
Motorized Frame  
Tray  
4 Toys  
(Toys may be different  
than shown.)  
Pad  
Seat Tube  
Arm  
2 Upper Legs  
Seat with Restraint System  
2 Feet  
2 Lower Legs  
1
#8 x / " Screw - 2  
2
M4 x 31.5 mm Bolt - 2  
M4 Lock Nut - 2  
ALL SHOWN ACTUAL SIZE  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp  
edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.  
Never substitute parts.  
Motorized Frame  
1
#8 x / " Screw - 2  
2
SHOWN ACTUAL SIZE  
L
Foot  
Lower Leg  
Tube  
Red Dot  
R
Elbow Foot  
Button  
Hole  
3
1
Locate the R and L on the underside of each elbow foot.The  
R indicates the right leg.The L indicates the left leg.  
While pressing the upper button on the right leg, fit it into  
the tube in the motorized frame. Make sure the upper button  
on the right leg “snaps” into the hole in the tube.  
• Position a lower leg so that it stands on a flat surface, as shown.  
Fit a foot onto the end of the lower leg.  
1
2
Insert a #8 x / " screw through the bottom of the foot  
Repeat this procedure to assemble the left leg to the  
motorized frame.  
and into the lower leg.Tighten the screw with a Phillips  
screwdriver. Do not over-tighten.  
When the legs are assembled correctly to the tubes in the  
motorized frame, you should not see the red dots.  
Repeat this procedure to assemble the other foot to the  
other lower leg.  
Red Dot  
Button  
Button  
Upper Leg  
Straight  
End  
Button  
Hole  
Feet  
Feet  
Lower Leg  
4
R
L
2
• Stand the assembly upright.  
• Pull the legs out so that the buttons “snap” into the holes in  
the motorized frame.  
• Position an upper leg so that the red dot is upward.  
When standing behind the product, all four feet should be  
flat upon the floor. And, check for an L marking on the left  
foot and an R marking on the right foot.  
While pressing the button on the straight end of an upper  
leg, insert the upper leg into a lower leg. Make sure the but-  
ton on the upper leg “snaps” into the hole in the lower leg.  
Repeat this procedure to assemble the other upper leg to the  
other lower leg.  
• If the feet are not flat upon the floor, or the left and right feet  
have been reversed, remove both lower legs from the upper  
legs. Replace them onto the opposite upper leg.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Seat  
Ruffle  
Seat  
Waist  
Belts  
Slot  
Crotch Belt  
Pad  
Slots  
5
7
• Position the seat upright.  
• Place the pad onto the seat with the ruffle toward the top  
of the seat.  
Fold the bottom of the pad up. Insert the crotch belt through  
the slot in the pad. Make sure the crotch belt is not twisted.  
Fold the top of the pad down. Insert the waist belts through  
the slots in the pad. Make sure the waist belts are not twisted.  
Hole  
Hole  
Elastic  
Loops  
8
Peg  
6
Elastic  
Loops  
Turn the seat upright.  
Fit the pad edges around the rim of the seat.  
• Hook the two fastener straps on each side of the pad under  
the rim on each side of the seat.  
Fold the top of the pad down.  
Insert the two elastic loops on the pad  
through the holes in the seat bottom  
Bottom View  
While holding the elastic loops in place, turn the seat  
face down.  
• Hook the elastic loop on the left side onto the peg on the  
right side.  
• Hook the elastic loop on the right side onto the peg on the  
left side.  
Hint: The elastic loops should cross over each other when  
attached correctly to the pegs.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
M4 x 31.5 mm Bolt  
Rounded  
Side  
Tray  
M4 Lock Nut  
Shown Actual Size  
Slot  
9
11  
Turn the seat upright.  
Insert the tray tabs into the slots in each side of the seat.  
Insert an M4 x 31.5 mm bolt through the seat tube arm  
and seat tube.  
Attach an M4 lock nut to the bolt. Make sure the rounded  
side of the lock nut faces out.  
• Using an adjustable wrench, hold the lock nut in place.  
Then using a Phillips screwdriver, tighten the bolt. Do not  
over-tighten.  
Seat Tube  
Arm Hole  
Press  
Seat Tube  
Button  
Motorized  
Frame Tube  
Hole  
10  
Press  
Seat Tube  
Button  
While pressing the button on the seat tube, slide the seat  
tube arm onto the seat tube. Make sure the button on the  
seat tube “snaps“ into the hole in the seat tube arm.  
12  
• Press the button on the seat tube and slide the seat tube  
into the motorized frame tube. Make sure the button on  
the seat tube snaps”into the larger hole in the motorized  
frame tube.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Mobile  
Clip  
Toy  
Clip  
Slot  
14  
Toy  
13  
M4 x 31.5 mm Bolt  
Rounded  
Side  
Fit the string (below the knot) of a toy  
through the slot in a clip on the mobile.  
• Pull down on the toy to be sure it is secure on the mobile.  
Repeat this procedure to assemble the other three toys to  
the mobile.  
Insert a M4 x 31.5 mm bolt  
through smaller hole in the  
motorized frame tube and into  
the seat tube.  
M4 Lock Nut  
Shown Actual Size  
Note: Toys may be different than those shown.  
Attach an M4 lock nut to the bolt. Make sure the rounded  
side of the lock nut faces out.  
• Using an adjustable wrench, hold the lock nut in place.  
Then, using a Phillips Screwdriver, tighten the bolt. Do not  
over-tighten.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ba tter y Tips  
Ba tter y Insta lla tion  
• Do not mix old and new batteries.  
• Do not mix different types of batteries: alkaline, standard  
(carbon-zinc) or rechargeable (nickel-cadmium).  
Remove the batteries during long periods of non-use.  
Always remove exhausted batteries from this product.  
Battery leakage and corrosion can damage this product.  
Dispose of batteries safely.  
• Do not dispose of batteries in a fire.The batteries may  
explode or leak.  
1.5V x 4  
“D(LR20)  
+
-
• Never short-circuit the battery terminals.  
• Non-rechargeable batteries are not to be recharged.  
SHOWN ACTUAL SIZE  
• Only batteries of the same or equivalent type as  
recommended in the battery installation instructions  
are to be used.  
Battery  
Compartment  
Door  
• If removable rechargeable batteries are used, they are only  
to be charged under adult supervision.  
Rechargeable batteries are to be removed from the product  
before they are charged.  
• If you use a battery charger, it should be examined regularly  
for damage to the cord, plug, enclosure and other parts.  
Do not use a damaged battery charger until it has been  
properly repaired.  
Battery  
Compartment  
• Using a coin, press the tab on the battery compartment door  
and remove it.  
Insert fourD(LR20) alkaline batteries, as indicated inside  
the battery compartment.  
Hint: We recommend using alkaline batteries for longer  
battery life.  
Replace the battery compartment door.  
Hint: If the swinging motion or mobile movement becomes  
noticeably slower or stops, remove the batteries and replace  
them with four, newD(LR20) alkaline batteries. Dispose of  
exhausted batteries properly.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Swing a nd Mobile Use  
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.  
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never  
substitute parts.  
Restraint Belts  
To Unfold  
Button  
Button  
Leg  
Waist Belt  
Leg  
Waist Belt  
Crotch Belt  
1
2
Firmly pull the legs outward. Make sure the buttons snap  
into the notches in the motorized frame.  
• Place your child in the seat.  
• Check to be sure the legs are locked into position by  
pushing the legs inward.The legs should not move.  
• Pull the crotch belt up between your childs legs and fasten  
both waist belts to the crotch belt. Make sure you hear a  
“click” on both sides.  
WARNING  
Anchored End  
Anchored End  
Buckle  
A
To prevent injury or death from falls  
or sliding out, always use the  
restraint system. Never rely on the  
tray to restrain child.  
B
B
A
Free End  
Free End  
3
To Tighten  
To Loosen  
To tighten the waist belts:  
Feed the anchored end of the waist belt up through the  
A
buckle to form a loop  
.
B
• Pull the free end of the waist belt  
.
Repeat this procedure to tighten the other waist belt.  
To loosen the waist belts:  
Feed the free end of the waist belt up through the buckle  
A
to form a loop  
.
Enlarge the loop by pulling on the end of the loop  
toward the buckle.  
• Pull the anchored end of the waist belt to shorten the  
B
free end of the waist belt  
.
Repeat this procedure to loosen the other waist belt.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Swing a nd Mobile Use  
Adjust Swing Motion  
Using the Tray  
PRESS  
Seat Tube Button  
Seat Tube  
Tray  
Tab  
TURN  
Slot  
6
Fit the tabs on the tray into the slots in the sides of the seat.  
To remove the tray, pull the tab out on one side of tray  
and lift.  
Storage  
4
Swing  
Cradle  
Button  
You can adjust the motion of the swing: side to side or  
front to back.  
Button  
• Press the seat tube button to unlock the seat tube.  
Rotate the seat tube to the desired position.  
Adjust Seat to Recline or Upright  
Lower Leg  
Button  
Lower Leg  
Button  
Upright  
7
Recline  
• Press the buttons on the back of the motorized frame while  
pushing the legs inward.  
Lean the swing frame against a wall for storage.  
IMPORTANT! Remove the batteries for long-term storage.  
Front Edge  
of Seat  
5
Press Seat Position Buttons  
Hint: The legs may be disassembled for long-term storage.  
Press the button on each lower leg and remove them from the  
upper legs.  
You can adjust the seat to two different positions:  
Recline or Upright.  
From behind the seat, press both seat position buttons.  
Lift the seat back until the buttons “snap” into the  
upright position.  
• Push the seat back down until the buttons “snap” into  
10  
the recline position.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Swing a nd Mobile Use  
Speed Dial  
Reset  
Button  
Mode Switch  
Control Panel  
• Slide the mode switch to:  
Swing and Mobile  
Hints:  
As with most battery-powered swings, a heavier child reduces  
the amount of swinging motion on all settings. In most cases,  
the low setting works best for a smaller child while the high  
setting works best for a larger child.  
If the low setting provides too much swinging motion for  
your child, try placing one end of a blanket underneath your  
child and let the other end of the blanket drape down  
while swinging.  
Swing Only  
Mobile Only  
Swing and Mobile Off  
Turn the speed dial to select any of six speed settings  
.
The mobile turns off after approximately seven minutes.  
To restart the mobile, press the reset button for another  
seven minutes of use.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pr oblems a nd Solutions  
Problem  
Probable Cause  
Solution  
Motor is not running;  
no swinging  
Mode switch is in OFF  
position  
Slide the mode switch to  
swing and mobile or  
swing only.  
or  
mobile only position  
Batteries incorrectly installed  
Remove the batteries and replace in correct orientation, as  
indicated inside the battery compartment.  
Dead batteries  
Replace all four batteries with four, fresh Dalkaline batteries.  
Motor is running but  
swinging stops after a  
few minutes  
Need to start swinging motion  
To start swinging motion, give the seat a light push.  
Swing motion setting is  
inappropriate for childs weight  
Adjust the speed dial to a higher speed setting and give the  
seat a light push.  
Weak batteries  
Replace all four batteries with four, fresh Dalkaline batteries.  
No difference noticed in  
swinging motion after  
speed dial is adjusted  
Swing did not have sufficient time  
to adjust to different setting  
Allow the swing time to adjust to new setting.  
Weak batteries  
Replace all four batteries with four, fresh Dalkaline batteries.  
Mobile does not work  
Mode switch is in OFF  
swing only position  
position or  
Slide mode switch to desired setting  
.
Mobile turns off automatically  
after seven minutes  
Press the reset button  
seven minutes.  
to restart mobile for another  
Ca re  
Remove the tray from the seat.  
• Unbuckle the restraint system.  
Remove the pad elastic loops from the pegs and unfasten the pad fasteners from the seat.  
Remove the pad from the restraint system.  
Remove the toys from the mobile.  
• Machine wash the pad and toys in cold water with a mild detergent. Do not use bleach.Tumble dry on low heat and  
remove promptly.  
To clean the seat, restraint system, tray, mobile and motorized frame, use a mild cleaning agent and damp cloth. Rinse with clean  
water to remove residue.  
Replace the pad onto the seat.  
Replace the toys on the mobile.  
• Periodically check the swing for loose fasteners or broken parts and tighten as needed.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.  
©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.  
Printed in China  
B0639a-0920  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ei Electronics Smoke Alarm Ei 100R User Manual
Extron electronic Stereo System USP 405 User Manual
Festool Saw TS 55 EQ User Manual
Fisher Paykel Cooktop OR90SDBGFPX User Manual
Gateway Computer Monitor VX730 User Manual
GE Ventilation Hood ZV755SPSS User Manual
GE Washer WWA9850R User Manual
Gianni Industries Door GK310 1224 User Manual
Gitzo Camcorder Accessories G1257LVL User Manual
Global Machinery Company Power Hammer RHD1500 User Manual