4200WATT
Portable Generator Owner’s Manual
Model No. 1305–0 (4200 Watt AC Generator) Manual No. B4242 Revision 2 (9/6/2000)
Visit our Generac website: www.generac-portables.com
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
• The generator produces a very powerful voltage that can
• Never operate the generator:
cause serious injury or death by electrocution. Never
touch bare wires or receptacles. Never permit a child
or any unqualified person to operate the generator.
in rain; in any enclosed compartment; when connected
electrical devices overheat; if electrical output is lost; if
engine or generator sparks; if flame or smoke is
observed while unit is running; if unit vibrates
excessively.
• Never handle any kind of electrical cord or device while
standing in water, while barefoot or while hands or feet
are wet. Death or serious injury from electrocution may
result.
GROUNDING THE
GENERATOR
The National Electric Code requires the frame and
external electrically conductive parts of the generator be
properly connected to approved earth ground. Local
electrical codes may also require proper grounding of the
unit. For this purpose, a grounding wing nut (Figure 1) is
provided on the cradle.
• Use a ground fault circuit interrupter (GFCI) in any damp
or highly conductive area (such as metal decking or steel
work).
• Never use worn, bare, frayed or otherwise damaged
electrical cords with the generator. Death, serious injury
and property damage from electrical shock may result.
• Gasoline is highly FLAMMABLE and its vapors
are EXPLOSIVE. Never allow smoking, open
flames, sparks or heat in the vicinity while
handling gasoline. Avoid spilling gasoline on a hot
engine. Comply with all laws regulating storage and
handling of gasoline.
Figure 1 — Grounding Wing Nut
• Do Not overfill the fuel tank. Always allow room for
fuel expansion. If tank is overfilled, fuel can overflow
onto a hot engine and cause a FIRE or an
EXPLOSION.
• Never store a generator with fuel in the tank where
gasoline vapors might reach an open flame, spark or pilot
light (as on a furnace, water heater, clothes dryer). FIRE
or an EXPLOSION may result.
Grounding Wing Nut
• The unit requires an adequate flow of cooling air for its
continued proper operation. Never operate the unit
inside any room or enclosure where the free flow of
cooling air into and out of the unit might be obstructed.
Allow at least 2 feet of clearance on all sides of generator,
even while operating unit outdoors, or you could damage
the unit.
Generally, connecting a No. 12 AWG (American Wire
Gauge) stranded copper wire to the grounding wing nut
and to an earth–driven copper or brass grounding rod
(electrode) provides adequate protection against electrical
shock. However, local codes may vary widely. Consult with
a local electrician for grounding requirements in your area.
Be sure to keep the ground wire attached while you
connect the electrode.
• Never start, or stop the unit with electrical loads
connected to receptacles with the connected devices
turned ON. Start the engine and let it stabilize before
connecting any electrical loads. Disconnect all electrical
loads before shutting down the generator.
Properly grounding the generator helps prevent electrical
shock if ground fault conditions exists in the generator or
in connected electrical devices. Proper grounding also helps
dissipate static electricity, which often builds up in
ungrounded devices.
• Do Not insert any object through cooling slots of the
engine. You could damage the unit or injure yourself.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
KNOW YOUR GENERATOR
Read this owner’s manual and safety rules before operating your generator.
Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
Fuel Tank
Circuit Breakers (AC)
120 Volt AC, 30 Amp
Receptacle
120/240 Volt AC,
20 Amp Receptacle
120 Volt AC, 20 Amp
Duplex Receptacle
Grounding Wing Nut
120 Volt AC, 20 Amp Duplex Receptacle — May be
used to supply electrical power for the operation of
120 Volt AC, 20 Amp, single phase, 60 Hz electrical
lighting, appliance, tool and motor loads.
240 Volt AC, 20 Amp, single phase, 60 Hz electrical
lighting, appliance, tool and motor loads.
Circuit Breakers (AC) — Each receptacle is provided
with a push-to-reset circuit breaker to protect the
generator against electrical overload.
120 Volt AC, 30 Amp Receptacle — May be used to
supply electrical power for the operation of 120 Volt AC,
30 Amp, single phase, 60 Hz electrical lighting, appliance,
tool and motor loads.
Fuel Tank — Capacity of 1.6 U.S. gallons (6 liters).
Grounding Wing Nut — Provides a tie-point for
connecting the generator frame to earth ground.
120/240 Volt AC, 20 Amp Receptacle — May be used
to supply electrical power for the operation of 120 and/or
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
• Fill fuel tank with clean, fresh, unleaded gasoline. Be
careful not to overfill. Allow 1/2" of tank space for fuel
expansion, as shown in Figure 2.
CARTON CONTENTS
Check all contents. If any parts are missing or damaged, call
the generator helpline at 1-800-270-1408. Review “Cold
Weather Operation” on page 7. Shipped with your
generator are:
Figure 2 — Typical Tank Expansion Space
•
•
•
Main unit
Engine and generator owner’s manuals
Muffler exhaust deflector
BEFORE STARTING THE
ENGINE
Add Engine Oil
• Make sure unit is on a level surface.
• Install fuel cap and wipe up any spilled gasoline.
• Follow the oil recommendations and oil fill instructions
given in the engine owner’s manual.
IMPORTANT: It is important to prevent gum deposits
from forming in essential fuel system parts such as the
carburetor, fuel filter, fuel hose or tank during storage.
Also, experience indicates that alcohol–blended fuels
(called gasohol, ethanol or methanol) can attract moisture,
which leads to separation and formation of acids during
storage. Acidic gas can damage the fuel system of an engine
while in storage. To avoid engine problems, the fuel system
should be emptied before storage of 30 days or longer. See
“Storage”. Never use engine or carburetor cleaner
products in the fuel tank or permanent damage may occur.
CAUTION! Any attempt to crank or start the
engine before it has been properly serviced with the
recommended oil results in an engine failure.
NOTE: The generator’s revolving field rides on a
pre–lubricated and sealed ball bearing that requires no
additional lubrication for the life of the bearing.
Add Gasoline
IMPORTANT: When running your unit in cold weather
be sure to shelter the unit from the wind.
DANGER! Never fill fuel tank indoors. Never fill
fuel tank when engine is running or hot. Do Not
light a cigarette or smoke when filling the fuel tank.
DANGER! Do Not overfill the fuel tank. Always
leave room for expansion.
• Use regular UNLEADED gasoline in the generator.
Do Not use premium gasoline. Do Not mix oil with
gasoline. Do Not overfill the gas tank.
• Clean area around fuel fill cap; remove cap.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
• Set the engine switch to the “ON” position (Figure 5).
OPERATING THE
GENERATOR
Figure 5 — Engine Switch
Engine Switch
Off
CAUTION! Never start or stop the unit with
electrical loads connected to the receptacles.
Starting the Engine
DANGER! Breathing hazard. Never run engine
indoors or in enclosed poorly ventilated areas.
Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
On
WARNING! Burn hazard. Temperature of muffler
and nearby areas may exceed 150°F (65°C). Avoid
these areas.
• Grasp starter grip and pull slowly until you feel some
resistance. Then pull cord out with rapid full arm stroke.
Let rope return slowly. Do Not let rope “snap back”
against starter.
• Unplug all electrical loads from generator receptacles
before starting the engine.
• If the choke lever has been moved to the “CLOSED”
position to start the engine, gradually move it to the
“OPEN” position as the engine warms up.
• Make sure the unit is in a level position.
• Move the fuel valve to the “ON” position (Figure 3).
Figure 3 — Fuel Valve
Connecting Electrical Loads
• Let engine stabilize and warm up for a few minutes after
starting.
• Plug in and turn on the desired 120 and/or 240 Volt AC,
single phase, 60 Hz electrical loads.
On
• Do Not connect 240 Volt loads to the 120 Volt duplex
receptacles.
Off
• To start a cold engine, move the choke lever to the
“CLOSED” position. To restart a warm engine, leave
the choke lever in the “OPEN” position (Figure 4).
• Do Not connect 3–phase loads to the generator.
• Do Not connect 50 Hz loads to the generator.
• DO NOT OVERLOAD THE GENERATOR. See
“Don’t Overload the Generator” on page 9.
Figure 4 — Choke Positions
Choke Lever
Stopping the Engine
• Unplug all electrical loads from generator panel
receptacles. Never start or stop engine with electrical
devices plugged in and turned ON.
• Let engine run at no-load for several minutes to stabilize
the internal temperatures of engine and generator.
Open
• Move engine switch to “OFF” position.
• Move the fuel valve to the “OFF” position.
Closed
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
• Ensure a minimum of two feet clearance between open
side of box and nearest object.
Cold Weather Operation
Under certain weather conditions (temperatures below
40°F [4°C] and a high dew point), your Generac generator
may experience problems.
• Face exposed end away from wind and elements.
• Enclosure should hold enough heat created by the
generator to prevent problems.
In an emergency, use the original shipping box as a
temporary shelter:
RECEPTACLES
• Cut off all flaps.
• Cut out one of the long sides of the box to expose
exhaust side of unit. Ensure a minimum of two feet
clearance between open side of box and nearest object.
This generator is equipped with the following receptacles:
120 Volt AC, 20 Amp Duplex
Receptacle
Each of these outlets is protected against overload by
20 Amp push–to–reset circuit breakers. Use each outlet to
operate 120 Volt, 60 Hz, single phase loads requiring
2,400 (2.4 kW) watts at 20 Amps of current (Figure 7).
• Cut appropriate slots to access receptacles of unit.
• Start unit, then place box over it.
WARNING!: Remove shelter when temperature
is above 40°F [4°C].
For a more permanent shelter, build a structure that will
enclose three sides and the top of the generator:
Figure 7 — 120 Volt, 20 Amp Duplex Receptacle
• Make sure entire muffler-side of generator is exposed, as
shown in Figure 6.
NOTE: A typical unit is shown here - your unit will differ
in appearance.
Figure 6 — Temporary Cold Weather Shelter
Wind
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
120/240 Volt AC, 20 Amp Locking
120 Volt AC, 30 Amp Locking Type
Receptacle
Receptacle
Use a NEMA L14-20 plug with this receptacle. Connect a
4-wire cord set rated for 250 Volts AC at 20 Amps (or
greater) (Figure 8). You can use the same 4-wire cord if
you plan to run a 120 Volt load.
Use a NEMA L5–30 plug with this receptacle. Connect a
3–wire cord set rated for 125 Volt AC loads at 30 Amps to
the plug (Figure 9).
Figure 9 — 120 Volt, 30 Amp Locking Receptacle
Figure 8 — 120/240 Volt, 20 Amp Locking Receptacle
This receptacle powers 120/240 Volt AC, 60 Hz, single
phase loads requiring up to 2,400 watts of power at
20 Amps for 120 Volts OR 4,200 watts of power (4.2 kW)
at 17.5 Amps for 240 Volts. The outlet is protected by a
push-to-reset circuit breaker.
Use this receptacle to operate 120 Volt AC, 60 Hz, single
phase loads requiring up to 3,600 watts (3.6 kW) of power
at 30 Amps. The outlet is protected by a 30 Amp
push–to–reset circuit breaker.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
• If the appliance, tool or motor does not give wattage,
multiply 120 Volts times ampere rating to determine
watts (volts x amps = watts).
DON’T OVERLOAD THE
GENERATOR
Overloading a generator in excess of its rated wattage
capacity can result in damage to generator and to
connected electrical devices. Observe the following, to
prevent overloading the unit:
• Some electric motors, such as induction types, require
about three times more watts of power for starting than
for running. This surge of power lasts for only a few
seconds when starting such motors. Be sure you allow
for this high starting wattage when selecting electrical
devices to connect to your generator. First figure the
watts needed to start the largest motor. Add to that
figure the running watts of all other connected loads.
• Add up the total wattage of all electrical devices to be
connected at one time. This total should NOT be
greater than the generator’s wattage capacity.
• The rated wattage of lights can be taken from light bulbs.
The rated wattage of tools, appliances and motors can
usually be found on a data plate or decal affixed to the
device.
• A Wattage Reference Guide (Figure 10) is provided to
help you determine how many items the generator can
operate at one time.
Figure 10 — Wattage Reference Guide
Recreational/Home Uses
Professional/Contractor Uses
Tool/Appliance....................................................Watts
AM/FM clock radio.....................................................................50
Light bulb....................................................................................100
Fan................................................................................................200
20" color TV..............................................................................400
*Deep freezer............................................................................500
Personal computer and 15" monitor...................................800
*1/3 hp furnace fan blower.....................................................800
Microwave oven........................................................................800
*18 cu ft refrigerator...............................................................800
Sump pump..............................................................................1000
Electric skillet..........................................................................1250
*½ hp water well pump........................................................1400
*12,000 Btu window air conditioner.................................1400
Space heater............................................................................1800
Electric water heater.............................................................4000
Tool/Appliance....................................................Watts
*1/3 hp airless sprayer.............................................................600
3/8" hammer drill .....................................................................600
Variable speed Sawzall®..........................................................960
½" power drill.........................................................................1000
Quartz-halogen work light...................................................1000
Belt sander...............................................................................1200
7 ¼" circular saw ...................................................................1500
7 ¼" worm drive saw............................................................1600
*1½ hp air compressor ........................................................1800
*10" power miter saw...........................................................1800
6" bench grinder.....................................................................1800
*6" table planer.......................................................................1800
*10" table/radial arm saw .....................................................2000
Wire feed welder...................................................................2400
* allow 3 times listed watts for starting this device
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4200 Watt Generator
To Clean the Generator
SPECIFICATIONS
• Use a damp cloth to wipe exterior surfaces clean.
Maximum Surge Watts . . . . . . . . . . . . . . . 5,250 Watts
Continuous Wattage Capacity . . . . . . . . . 4,200 Watts
Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0
Rated Maximum Continuous Load Current
• Soft, bristle brush may be used to loosen caked on dirt
or oil.
• A vacuum cleaner may be used to pick up loose dirt
and debris.
At 120 Volts . . . . . . . . . . . . . . . . . . . . . . . 35 Amps
At 240 Volts . . . . . . . . . . . . . . . . . . . . . . 17.5 Amps
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-phase
Rated Frequency . . . . . . . . . . . . . . . . . . . . . . 60 Hertz
• Low pressure air (not to exceed 25 psi) may be used to
blow away dirt. Inspect cooling air slots and opening on
generator. These openings must be kept clean and
unobstructed.
MAINTENANCE
STORAGE
The unit should be started at least once every seven days
and allowed to run at least 30 minutes. If this cannot be
done and you must store the unit for more than 30 days,
use the following guidelines to prepare it for storage.
RECOMMENDATIONS
The Owner/Operator is responsible for making sure that
all periodic maintenance tasks are completed on a timely
basis; that all discrepancies are corrected; and that the
unit is kept clean and properly stored. Never operate a
damaged or defective generator.
Generator Storage
• Clean the generator as outlined in “To Clean the
Generator” on this page.
Engine Maintenance
See engine owner’s manual for instructions.
• Check that cooling air slots and openings on generator
are open and unobstructed.
Generator Maintenance
DANGER! Storage covers can be flammable. Do
Not place a storage cover over a hot generator.
Let the unit cool for a sufficient time before
placing the cover on the unit.
Generator maintenance consists of keeping the unit clean
and dry. Operate and store the unit in a clean dry
environment where it will not be exposed to excessive
dust, dirt, moisture or any corrosive vapors. Cooling air
slots in the generator must not become clogged with
snow, leaves or any other foreign material.
Engine Storage
See engine owner’s manual for instructions.
Note: Do Not use a garden hose to clean the generator.
Water can enter engine fuel system and cause problems.
In addition, if water enters generator through cooling air
slots, some of the water will be retained in voids and
cracks of the rotor and stator winding insulation. Water
and dirt buildup on the generator internal windings will
eventually decrease the insulation resistance of these
windings.
Other Storage Tips
• Do Not store gasoline from one season to another.
• Replace your gasoline can if it starts to rust. Rust
and/or dirt in a gasoline can cause problems when you
use that fuel with this unit.
• Store in clean and dry area.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
TROUBLESHOOTING
Problem
Cause
Solution
1. Circuit breaker is open.
1. Reset circuit breaker.
2. Poor connection or defective cord set. 2. Check and repair.
Engine is running, but
no AC output is
available.
3. Connected device is bad.
3. Connect another device that is in good
condition.
4. Contact Generac service facility.
4. Fault in generator.
1. Short circuit in a connected load.
2. Generator is overloaded.
1. Disconnect shorted electrical load.
2. See “Don’t Overload the Generator” on
page 9.
3. Contact Honda service facility.
4. Contact Generac service facility.
Engine runs good but
bogs down when
loads are connected.
3. Engine speed is too slow.
4. Shorted generator circuit.
1. Engine switch set to Off.
2. Dirty air cleaner.
3. Out of gasoline.
1. Set switch to ON.
2. Clean or replace air cleaner.
3. Fill fuel tank.
4. Stale gasoline.
5. Spark plug wire not connected to
spark plug.
4. Drain gas tank and fill with fresh fuel.
5. Connect wire to spark plug.
Engine will not start;
or starts and runs
rough.
6. Bad spark plug.
7. Water in gasoline.
8. Overchoking.
6. Replace spark plug.
7. Drain gas tank; fill with fresh fuel.
8. Set choke to “OFF” position.
9. Fill crankcase to proper level.
10. Contact Honda service facility.
11. Contact Honda service facility.
12. Contact Honda service facility.
9. Low oil level.
10. Excessively rich fuel mixture.
11. Intake valve stuck open or closed.
12. Engine has lost compression.
1. Out of gasoline.
2. Low oil level.
3. Fault in engine.
1. Fill fuel tank.
2. Fill crankcase to proper level.
3. Contact Honda service facility.
Engine shuts down
during operation.
1. Load is too high.
1. See “Don’t Overload the Generator” on
page 9.
Engine lacks power.
2. Dirty air filter.
2. Replace air filter.
3. Engine needs to be serviced.
3. Contact Honda service facility.
1. Choke is opened too soon.
1. Move choke to halfway position till engine
runs smoothly.
2. Contact Honda service facility.
Engine “hunts” or
falters.
2. Carburetor is running too rich or too
lean.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
SCHEMATIC DIAGRAM
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
WIRING DIAGRAM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
EXPLODED VIEW AND PARTS LIST– MAIN UNIT
Item Part #
Qty Description
Item Part #
Qty Description
1
2
NSP
1
6
2
2
1
1
1
2
1
2
4
1
4
1
4
1
2
ENGINE, Honda 8 hp
18
91825
1
ASSEMBLY, Brush & Bridge
52858
70642
76222
AB4239
66365G
66825C
26850
86494
84242
86307
22695
86308C
67022
74908
B4871
66849
NUT, M8-1.25 Flange Lock
MOUNT, 45° Vibration
SCREW, M8-1.25 x 40mm
CRADLE
Rectifier
3
19
20
21
22
23
24
25
26
27
28
29
30
31
32
25244
22129
91844J
82857
22769
86292
B91859J
81917
47480
96796
65791
14353621
B4702
B4986
2
2
1
2
1
1
1
1
1
1
1
1
1
1
NUT, 5/16 - 18 Hex
WASHER, M8 - 5/16 Lock
ASSEMBLY, Rotor
MOUNT, Rubber
WASHER, #10 Shakeproof
SCREW, #10 Self-Drilling
ASSEMBLY, Stator
PIN, M4 x 10mm Roll
BOLT, Rotor
4
5
6
HOUSING, Adapter
7
CARRIER, Rear Bearing
WASHER, 1/4" Shakeproof
SCREW, M6 x 16mm Wing
GROMMET, Plastic
8
9
10
11
12
13
14
15
16
17
SCREW, 5/16"-24 x 3/4" SEMS
CONNECTOR, 6-pin Male
BOLT, Stator
WASHER, Special
BEARING
GROMMET, Rubber
WIRE, Ground
SCREW, M5-0.8 x 10mm
COVER, Bearing Carrier
SCREW, M5-0.8 x 15mm
DECAL, Engine Throttle
DECAL, Ground
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 4,200 Watt Generator
EXPLODED VIEW AND PARTS LIST– CONTROL PANEL
Item Part #
Qty Description
Item Part #
Qty Description
1
2
3
4
5
B4245
75475
82881
82308
B2153
1
6
3
4
4
PANEL, Control
9
22264
51715
68867
6
6
1
WASHER, No. 8 Lock
SCREW, M4 - 0.7 x 10mm
WASHER, Internal Lock
SCREW, Self Tapping
SCREW, No. 10 Self Drilling x
7/8"
10
11
NUT, M4 0.7 Hex
RECEPTACLE, 120/240 Volt,
20 Amp Locking
12
68759
1
OUTLET, 120 Volt, 20 Amp
Duplex
6
7
23365
68868
6
1
WASHER, No. 8 Serrated Lock
RECEPTACLE, 120 Volt, 30 Amp
Locking
13
14
15
16
75207
75207A
81919
22694
2
1
1
1
CIRCUIT BREAKER, 20 Amp
CIRCUIT BREAKER, 30 Amp
CONTROL PANEL, Back
CONNECTOR, 6-Pin Male
8
38150
6
WASHER, No. 8 Flat
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FOR PORTABLE GENERATORS
(EXCEPT GN ENGINE SERIES)
Generac Portable Products (hereafter referred to as the COMPANY) warrants to the original purchaser that its generator
will be free from defects in materials or workmanship for a period of one year* from the date of original purchase. This
warranty does not apply to units used for prime power in place of utility. This warranty does not include the gasoline
engine when furnished or attached because such engine is covered solely by the warranty of the manufacturer of the
engine. Starting batteries are not warranted by the COMPANY.
*NOTE: Rental units, demonstrators, commercial applications, such as construction or income producing, are warranted
for 90 days. Rental units, demonstrators, or commercial applications such as construction or utility which are resold are
not covered under warranty by the COMPANY. Any warranty, whether expressed or implied, rests solely with the seller.
During said warranty period, the COMPANY will, at its option, repair or replace any part which, upon examination by the
COMPANY is found to be defective under normal use and service. All transportation costs under warranty, including
return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser. This warranty does not
include nominal maintenance and service and does not apply to a generator set, or parts, which have been subjected to
improper or unauthorized installation, misuse, negligence, accident, overloading, overspeeding, improper maintenance,
repair or storage so as, in the COMPANY's judgment, to adversely affect its performance and reliability.
THERE IS NO OTHER EXPRESS WARRANTY. THE COMPANY HEREBY DISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT PERMITTED BY LAW. THE DURATION OF
ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO THE TIME PERIOD AS
SPECIFIED IN THE EXPRESS WARRANTY. LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, OR
SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED TO THE EXTENT
PERMITTED BY LAW. THE COMPANY ALSO DISCLAIMS ANY RESPONSIBILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES SUCH AS THE LOSS OF TIME OR THE USE OF THE POWER
EQUIPMENT, OR ANY COMMERCIAL LOSS DUE TO THE FAILURE OF THE EQUIPMENT; AND ANY
IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusions or limitations of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights, which vary from state to state.
This warranty is effective for all products manufactured after June, 1998, and supersedes all prior warranties of the
COMPANY.
For service, contact your nearest COMPANY authorized warranty service facility or call 1-877-544-0982. Warranty
service can only be performed by a COMPANY authorized service facility. At the time of requesting warranty service,
evidence of original purchase date must be presented.
GENERAC PORTABLE PRODUCTS
Jefferson, Wisconsin U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|