®
Fujitsu Stylistic
ST5111 / ST5112
Tablet PC
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
C o p y r i g h t
Copyright and Trademark Information
Fujitsu Computer Systems Corporation has made every
effort to ensure the accuracy and completeness of this
document. Because ongoing development efforts are
made to continually improve the capabilities of our prod-
ucts, however, the data contained herein represents
Fujitsu design objectives and is provided for comparative
purposes; actual results may vary based on a variety of
factors. This product data does not constitute a warranty.
Specifications are subject to change without knowledge.
SigmaTel is a registered trademark of SigmaTel, Inc.
Bluetooth and the Bluetooth logo are registered trade-
marks of Bluetooth SIG, Inc.
Memory Stick is a registered trademark of Sony Corpora-
tion and/or its affiliates
Wi-Fi is a trademark of the Wireless Ethernet Compati-
bility Alliance (WECA).
All other products are trademarks or registered trade-
marks of their respective companies.
Fujitsu and the Fujitsu logo are registered trademarks of
Fujitsu Limited; Stylistic is a registered trademark of
Fujitsu Computer Systems Corporation.
Warning
Microsoft, Windows, and Windows Vista are registered
trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
Handling the cord on this product will expose
you to lead, a chemical known to the State of
California to cause birth defects or other
reproductive harm.
PCMCIA and CardBus are registered trademarks of the
Personal Computer Memory Card International Associa-
tion.
Wash hands after handling.
Copyright 2007 Fujitsu Computer Systems Corporation.
All rights reserved. No part of this publication may be
copied, reproduced, or translated, without the prior
written consent of Fujitsu Computer Systems
Centrino, Intel, and Intel Core are trademarks or registered
trademarks of Intel Corporation or its subsidiaries in the
United States and other countries.
OmniPass is a trademark of Softex, Inc.
Corporation. No part of this publication may be stored
or transmitted in any electronic form without the prior
consent of Fujitsu Computer Systems Corporation.
Adobe, Acrobat, and Acrobat Reader are either registered
trademarks or trademarks of Adobe Systems Incorpo-
rated in the United States and/or other countries.
B5FJ-4111-01EN-00
Atheros and Super AG are registered trademarks of
Atheros Communications, Inc.
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name:
Address:
Fujitsu Computer Systems Corporation
1250 E. Arques Avenue, MS 122
Sunnyvale, CA 94085
Telephone:
408-746-6000
Declares that product:
Model Series: Stylistic® ST5111 Tablet PC
Stylistic® ST5112 Tablet PC
Complies with Part 15 of the FCC Rules
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and, (2) This device must accept any interference
received, including interference that may cause undesired operation.
Note: For more detailed information about the FCC rules and their applicability to the Stylistic ST5100 Series
Tablet PC, refer to Chapter 5 of this document.
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C
-
U s e r ’ s G u i d e
IMPORTANT SAFETY INSTRUCTIONS
For Authorized Repair Technicians Only
■
This unit requires an AC adapter to operate. Use only
UL Listed Class 2 Adapters with an output rating of 16
VDC, with a current of 3.75A minimum.
Danger of explosion if Lithium (clock) bat-
tery is incorrectly replaced. Replace only
with the same or equivalent type recom-
mended by the manufacturer. Dispose of
used batteries according to the manufac-
turer’s instruction.
AC Adapter output polarity:
+
For continued protection against risk of
fire, replace only with the same type and
rating fuse.
■
When using your tablet PC equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons,
including the following:
■
System Disposal
Do not use this product near water for example,
near a bathtub, washbowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
Avoid using the modem during an electrical storm.
There may be a remote risk of electric shock from
lightning.
LAMP(S) INSIDE THIS PRODUCT
CONTAIN MERCURY AND MUST
BE RECYCLED OR DISPOSED OF
■
Hg
ACCORDING TO LOCAL, STATE, OR
FEDERAL LAWS.
■
■
Do not use the modem to report a gas leak in the
vicinity of the leak.
Use only the power cord and batteries indicated in
this manual. Do not dispose of batteries in a fire.
They may explode. Check with local codes for
possible special disposal instructions.
To reduce the risk of fire, use only No. 26 AWG or
larger UL Listed or CSA Certified Telecommunica-
tion Line Cord
■
■
For TV Tuner Models: To protect from overvoltages
and transients on the Cable Distribution System, make
sure that the outer shield of the coaxial cable is con-
nected to earth (grounded) at the building premises as
close to the point of cable entrance as practicable, as
required per NEC Article 820.93, ANSI/NFPA 70:
2005. If you have questions about your CATV installa-
tion, contact your service provider.
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b l e o f C o n t e n t s
®
Fujitsu Stylistic ST5111/ST5112 Tablet PC
Table of Contents
Adjusting the Display Brightness . . . . . . . . . . . . 29
Using the Pen . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PREFACE
Calibrating the Pen . . . . . . . . . . . . . . . . . . . . . . 31
Installing a Pen Tether . . . . . . . . . . . . . . . . . . . . 31
Replacing the Pen Tip . . . . . . . . . . . . . . . . . . . . 31
Charging the Battery . . . . . . . . . . . . . . . . . . . . . 31
Removing and Installing the Battery. . . . . . . . . . 32
Tips for Conserving Battery Power. . . . . . . . . . . 32
Modem Connection . . . . . . . . . . . . . . . . . . . . . 33
Memory Stick/SD Card Slot . . . . . . . . . . . . . . . . 33
PC Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Removing and Installing Memory . . . . . . . . . . . 34
About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . 1
Fujitsu Contact Information . . . . . . . . . . . . . . . . . 1
Limited Warranty Information . . . . . . . . . . . . . . . 1
1
GETTING STARTED
WITH YOUR TABLET PC
In-box Items for the Stylistic Tablet PC. . . . . . . . . 5
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . 5
Stylistic Tablet PC Features. . . . . . . . . . . . . . . . . . 6
Status Display. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Application Buttons . . . . . . . . . . . . . . . . . . . . . . 13
Navigation Buttons. . . . . . . . . . . . . . . . . . . . . . . 15
Tertiary Functions of Buttons . . . . . . . . . . . . . . . 16
Security Functions of Application Buttons. . . . . . 17
Setting up the Security Panel . . . . . . . . . . . . . . . 17
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using Your Security Panel . . . . . . . . . . . . . . . . . 18
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Uninstalling the Security Panel Application. . . . . 18
Installing Click Me! . . . . . . . . . . . . . . . . . . . . . . 19
Connectors and Peripheral Interfaces . . . . . . . . . 20
3
CARE AND MAINTENANCE
Caring for Your Tablet PC . . . . . . . . . . . . . . . . . 39
Protecting the Display Screen. . . . . . . . . . . . . . . 39
Storing the Tablet PC. . . . . . . . . . . . . . . . . . . . . 40
Avoiding Overheating . . . . . . . . . . . . . . . . . . . . 40
Cleaning the Display Screen. . . . . . . . . . . . . . . . 41
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 41
Restoring the Pre-Installed Software . . . . . . . . . 42
Restoring the Factory Image . . . . . . . . . . . . . . . 42
Automatically Downloading Driver Updates. . . . 43
4
2
SYSTEM SPECIFICATIONS
USING YOUR
STYLISTIC TABLET PC
Processing Specifications . . . . . . . . . . . . . . . . . . 47
Memory/Storage Specifications . . . . . . . . . . . . . 47
Display Specifications. . . . . . . . . . . . . . . . . . . . . 47
Physical Specifications . . . . . . . . . . . . . . . . . . . . 47
Interface Specifications . . . . . . . . . . . . . . . . . . . 47
Power Specifications . . . . . . . . . . . . . . . . . . . . . 48
Environmental Specifications . . . . . . . . . . . . . . . 48
Agency Approval Specifications . . . . . . . . . . . . . 48
Additional Specifications . . . . . . . . . . . . . . . . . . 48
Regulatory Information . . . . . . . . . . . . . . . . . . . 49
System States. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Powering Up the Tablet PC . . . . . . . . . . . . . . . . 26
Booting the System the First Time . . . . . . . . . . . 26
Registering Your Stylistic
Tablet PC with Fujitsu . . . . . . . . . . . . . . . . . . . . 27
Shutting Down the System. . . . . . . . . . . . . . . . . 27
Suspending System Operation . . . . . . . . . . . . . . 27
Resuming System Operation . . . . . . . . . . . . . . . 28
Using the Shock Sensor Utility . . . . . . . . . . . . . . 29
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
APPENDIX A: WIRELESS LAN/
BLUETOOTH USER’S GUIDE
Before Using the Wireless LAN
Stopping transmission . . . . . . . . . . . . . . . . . . . . 55
Starting transmission . . . . . . . . . . . . . . . . . . . . . 56
Connecting the WLAN
Configuring the WLAN with Windows Vista . . . 57
Configuring the WLAN Using Windows XP . . . . 57
Connection to the network . . . . . . . . . . . . . . . . 59
Troubleshooting the WLAN
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 63
Wireless LAN Glossary
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
IP address information
Additional information . . . . . . . . . . . . . . . . . . . . 67
WLAN Specifications
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Using the Bluetooth Device
What is Bluetooth?. . . . . . . . . . . . . . . . . . . . . . . 69
Where to find information about Bluetooth . . . . 69
APPENDIX B: SECURITY
DEVICE USER’S GUIDE
Fingerprint Sensor Device
Introducing the Fingerprint Sensor Device . . . . . 73
Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . 73
Installing OmniPass . . . . . . . . . . . . . . . . . . . . . . 73
User Enrollment . . . . . . . . . . . . . . . . . . . . . . . . . 74
Using OmniPass. . . . . . . . . . . . . . . . . . . . . . . . . 75
Configuring OmniPass . . . . . . . . . . . . . . . . . . . . 77
OmniPass Control Center. . . . . . . . . . . . . . . . . . 78
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 79
Trusted Platform Module Installation
TPM installation . . . . . . . . . . . . . . . . . . . . . . . . . 80
Index
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
P r e f a c e
Download from Www.Somanuals.com. All Manuals Search And Download.
P r e f a c e
FUJITSU CONTACT INFORMATION
Service and Support
You can contact Fujitsu Service and Support in the
Preface
following ways:
ABOUT THIS GUIDE
The Stylistic ST5100 Series Tablet PC is a high-
performance, pen-based computer that has been
designed to support Microsoft Windows XP Tablet PC
Edition or Windows Vista Business.
®
■
Toll free: 1-800-8Fujitsu (1-800-838-5487)
E-mail: [email protected]
Website:
■
®
®
■
This manual explains how to operate your Fujitsu
Stylistic ST5100 Series Tablet PC hardware and built-in
system software.
Before you place the call, you should have the
following information ready so the customer support
representative can provide you with the fastest possible
solution:
The Stylistic ST5100 Series Tablet PC is a completely self-
contained unit with an active-matrix (TFT) color
indoor-outdoor LCD display and an active digitizer. It
has a powerful interface that enables it to support a
variety of optional features.
■
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
■
■
■
■
Conventions Used in the Guide
Keyboard keys appear in brackets.
Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].
■
■
Type of device connected, if any
Fujitsu Shopping Online
You can go directly to the online store by going to the
Pages with additional information about a specific topic
are cross-referenced within the text.
Example: (See page xx.)
On screen buttons or menu items appear in bold
Example: Click OK to restart your Tablet PC.
You must have an active internet connec-
tion to use the online URL links.
The information icon highlights
information that will enhance your
understanding of the subject material.
LIMITED WARRANTY INFORMATION
Your Stylistic ST5100 Series Tablet PC is backed by an
International Limited Warranty. Check the service kit
that came with your system for warranty terms and
conditions.
The caution icon highlights information
that is important to the safe operation of
your computer, or to the integrity of your
files. Please read all caution information
carefully.
The warning icon highlights information
that can be hazardous to either you, your
computer, or your files. Please read all
warning information carefully.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
P r e f a c e
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Getting Started
with Your Tablet PC
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
4
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
Getting Started with Your Stylistic Tablet PC
The Stylistic ST5100 Series Tablet
PC is available with either a 10.4”
reflective display or a 12.1” transmissive
display. For purposes of illustration, the 12.1”
model is used throughout this document. Please
refer to the Specifications chapter for additional details.
Figure 1-1. Stylistic ST5100 Series Tablet PC
®
The Stylistic ST5100 Series Tablet PC is a high-
performance, pen-based computer that has been
OPTIONAL ACCESSORIES
There are many optional accessories that can be used
with the Stylistic ST5100 Series Tablet PC. For the latest
list of accessories available for your Tablet PC, be sure to
fujitsu.com. Refer to the instructions provided with these
accessories for details on their use.
®
®
designed to support Microsoft Windows XP Tablet PC
Edition 2005 or Windows Vista™ Business. This chapter
provides an overview of the Stylistic ST5100 Series Tablet
PC and its features.
IN-BOX ITEMS FOR THE STYLISTIC
ST5100 SERIES TABLET PC
Verify that the following items are included in the box
with your Tablet PC:
•
•
•
•
•
•
•
•
•
•
•
•
Stylistic ST5100 Series active pen
Pen tips (quantity: 5)
Pen tip removal tool
Pen tether
Main battery
Power cord
AC adapter
Screen protectors (quantity: 2)
Getting Started Guide
Quick Tips Guide
Drivers and Application Restore (DAR) DVD
System Restore DVD
5
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
STYLISTIC TABLET PC FEATURES
Features and controls that you use to operate the Stylistic ST5100 Series Tablet PC are outlined below and illustrated in
Figures 1-2 through 1-6. Details on using these features and controls are provided later in this manual.
Infrared Keyboard/Mouse Port
2nd Built-in Microphone
(12.1” model only)
Speaker
Fingerprint Swipe Sensor
(12.1” model only)
System Status LEDs
Display
Power On/Suspend/
Resume Button
Application/Security Buttons
Built-in
Microphone
Infrared Keyboard/Mouse Port
Navigation Buttons
Figure 1-2. Stylistic ST5100 Series Tablet PC Features (Front View)
•
Application/Security buttons: Allow you to quickly
launch pre-defined applications, utilities, and
security features by pressing a button. (See
Front Features:
1
•
Infrared keyboard/mouse ports: The infrared ports
are used for communicating with a proprietary
infrared keyboard or mouse.†
Application Buttons on page 13 for more information.)
•
Navigation buttons: The navigation buttons allow
you to move: Page Up/Page Down, Tab Right/Tab
Left, Cursor Up/Cursor Down, and Cursor Right/
Cursor Left. (See Navigation Buttons on page 15 for
more information.)
•
•
Speaker: Allows you to listen to audio files.
Fingerprint Swipe Sensor: The optional fingerprint
swipe sensor allows you to start your system by
swiping your finger over the sensor. (See Fingerprint
Sensor Device on page 73 for more information.)
•
Built-in Microphones: The built-in microphone(s)
allow you to input mono audio. Note that the 10.4”
model has one microphone; the 12.1” model has two.
•
•
System status LEDs: Indicate the operational status
of the Tablet PC and hard disk drive, the charge level
of the battery, and the security panel. (See Status
Display on page 11 for more information.)
†
These peripherals and accessories are sold separately.
Power On/Suspend/Resume button: Allows you to
turn on, off, standby, resume, hibernate or wake the
Tablet PC in order to optimize battery life. (See
Powering Up the Tablet PC on page 26 for more
information.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
Memory
Module Cover
System Interface
Connector
Battery
Battery Release Latch
Tablet Dock
Latch Points
Thermal Suede
Wireless LAN*
On/Off Switch
Figure 1-3. Stylistic ST5100 Series Tablet PC Features (Back View)
•
Thermal Suede: Several areas of the system back are
covered with “thermal suede”. This material should
not be removed. It is designed to minimize the heat
that the user feels when the system has been operating
for an extended period of time.
Back Features:
1
•
Memory module cover: Removable cover over the
memory modules. (See Removing and Installing
Memory on page 34 for more information.)
•
•
System interface connector: Allows you to connect
•
Wireless LAN module cover: Provides protection for
the optional wireless LAN radio. (See Connecting the
WLAN on page 57 for more information.)
the optional Stylistic Tablet Dock.†
Removable battery: Can be removed and replaced
with a charged battery.† (See Removing and Installing
the Battery on page 32 for more information.)
•
Wireless LAN/Bluetooth On/Off switch: For systems
with the optional wireless LAN radio or Bluetooth
device, this switch toggles the radio on or off. (See
Using the Bluetooth Device on page 69 for more
information.)
•
•
Battery release latch: Used to release the removable
battery.
Tablet Dock latch point: Allows you to attach the
system to an optional Tablet Dock.†
†
These peripherals and accessories are sold separately.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
Pen Holder
Pen Tether Point
PC Card Slot
PC Card Eject Button
Air flow vents
SD Card/Memory Stick Slot
IrDA/FIR Port
Smart Card Slot
Figure 1-4. Stylistic ST5100 Series Tablet PC Features (Top View)
Top Features:
1
To protect your tablet from damage and to
optimize system performance, be sure to
keep all air all vents unobstructed, clean,
and clear of debris. This may require
periodic cleaning, depending upon the
environment in which the system is used.
•
•
•
Pen: The main input device that you use to execute
programs and enter data. A pen holder is built into
the Tablet PC to store the pen when not in use. (See
Using the Pen on page 30 for more information.)
Pen Tether Point: The pen tether point is used to
attach a pen tether to help prevent loss of the pen.
(See Installing a Pen Tether on page 31 for more
information.)
Do not operate the tablet in areas where
the air vents can be obstructed, such as in
tight enclosures or on soft surfaces like a
bed or cushion.
PC Card slot: Allows you to insert a Type I or Type II
PCMCIA Card† in the system. (See PC Card Slot on
page 33 for more information.)
•
•
SD Card/Memory Stick Slot: The Secure Digital
(SD) card/Memory Stick slot allows you to insert a
flash memory card† for data storage. Flash memory
cards allow you to transfer data to and from a variety
of different digital devices. (See Memory Stick/SD
Card Slot on page 33 for more information.)
•
•
PC Card Eject Button: The PC Card eject button is
used to remove a PC Card from the PC Card slot.
IrDA/FIR port: Provides an infrared interface for
communication with devices compliant with IrDA
Standard Revision 1.1.
Smart Card Slot: The dedicated Smart Card slot
allows you to insert a Smart Card† on which you can
store such data as medical information or electronic
“cash”.
•
Air flow vents: Provides secondary cooling for
processor.
†
These peripherals and accessories are sold separately.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
External Monitor Connector (behind cover)
IEEE 1394 Jack
LAN Jack
Microphone Jack
Modem Jack
Lock Slot
Headphone Jack
USB 2.0 Ports
DC Input Jack
Latch Point
Figure 1-5. Stylistic ST5100 Series Tablet PC Features (Left Side View)
Left-Side Features:
1
•
USB 2.0 ports: Allow you to connect Universal Serial
• Modem jack: Allows you to connect a standard RJ-11
Bus-compliant devices (compliant with USB
Standard Revision 2.0) to the Tablet PC. Additional
USB ports are located on the optional Tablet Dock†.
connector to the Tablet PC’s internal 56 Kbps
modem. Note that the internal 56 Kbps modem
module installed in the Stylistic ST5100 Series Tablet
PC has actual maximum transfer rates of 53 Kbps
(receive), 33.6 Kbps (send), and 14.4 Kbps (fax).
Download rates are limited to 53 Kbps in the United
States due to FCC restrictions. (See Modem
•
•
•
Headphone Jack: Allows you to connect a set of stereo
headphones†.
Microphone Jack: Allows you to connect an external
microphone†.
Connection on page 33 for more information.)
•
LAN jack: Allows you to connect a standard RJ-45
connector to the Tablet PC’s internal local area
network (LAN).
IEEE 1394 Jack: Allows you to connect IEEE 1394
(Firewire) peripherals such as digital video cameras†
or external hard drives† to your Tablet PC.
•
•
Lock slot: Allows you to attach a compatible security
•
•
External Monitor Connector: The External Monitor
connector allows you to connect an external VGA,
XGA, SVGA, or UXGA monitor.
cable.†
DC input connector: Allows you to connect the AC
adapter or auto adapter.†
Latch Point: Used in conjunction with the optional
†
Tablet Dock to secure system to dock.
These peripherals and accessories are sold separately.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
Infrared Keyboard/Mouse Port
Pen / Pen Holder
Optional Wireless LAN location
Latch Point
Figure 1-6. Stylistic ST5100 Series Tablet PC Features (Right Side View)
Right-Side Features:
1
•
Pen: The main pointing device that you use to
execute programs and enter data. A pen holder is
built into the Tablet PC to store the pen when not in
use.
•
Infrared keyboard/mouse port: The infrared port
wraps around the front and bottom of the display,
and is used for communicating with an optional
proprietary infrared keyboard or mouse†.
•
•
Latch Point: Used in conjunction with the optional
Tablet Dock to secure system to dock.
Wireless LAN location: The optional wireless LAN
device is located inside of the system housing. (See
Connecting the WLAN on page 57 for more
information.)
†
These peripherals and accessories are sold separately.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
STATUS DISPLAY
Icons appear under each of the system status LEDs in the
status display indicating the status of system functions
such as system power and battery charge level. The loca-
tion of icons in the Status display is shown in Figure 1-7.
Power
Charge/DC In
Battery
Security
Table 1-1. explains how the LEDs associated with the
individual icons are displayed, and describes what the
variations of that display indicate. (If an icon is not
displayed, it indicates that the related system function is
off or inactive.
HDD Access
Figure 1-7.
Status Display Icons
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the
rate of one second on, five seconds off.
Icon
Mode/State
• On State
LED State
Remarks
Power
Green, continuous
The system is powered on and ready for
use.
• Idle Mode
• Standby
Green, blinking
Off
The system has suspended and saved active
settings to RAM.
• Off State
• Hibernate
• On State
• Idle Mode
• Standby
The system has suspended and saved
settings and data to the hard disk drive.
Charge/DC
In
Amber
Green
AC adapter and battery are available and
system is charging.
• AC adapter and battery are available
and system is not charging (battery fully
charged).
• Hibernate
• Off State
• AC adapter is available but battery is
not present.
Amber, blinking
Off
AC adapter and battery are available and
waiting to charge (battery is out of thermal
range).
AC adapter is not available.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the
rate of one second on, five seconds off.
Icon
Mode/State
• On State
LED State
Remarks
Battery
Green, continuous
Amber, continuous
Red, continuous
Red, blinking
Battery charge is between 50%-100%
Battery charge is between 13%-49%
Battery charge is between 0%-12%
There is a battery error.
• Idle Mode
• Standby,
without AC
adapter
Green, blinking slow
Battery charge is between 50%-100%.
Amber, blinking slow Battery charge is between 13%-49%.
Red, blinking slow
Battery charge is between 0%-12%.
• Standby with AC
adapter
• Hibernate,
with AC adapter
Off
Battery is not installed, or system is off or in
Hibernate mode.
• Off State
• Hibernate,
without AC
adapter
If battery is inserted during power off, LED
blinks amber for 4 seconds to detect
battery. Battery status is displayed for 5
seconds after that.
HDD Access
• On State (or
flashing)
Green
Off
Displayed when hard disk drive is accessed.
• Idle Mode
• Standby
Hard disk drive is not being accessed.
• Hibernate
• Off State
• On State
Security
Green, continuous
(until password is
entered)
The Security Indicator lights (if a password
was set) when the system resumes from
Off or Standby modes. You must enter the
password that was set in the Security Panel
before your system will resume operation.
(See Security Functions of Application Buttons
on page 17 for more information.)
Table 1-1. System Status Indicators
12
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
APPLICATION BUTTONS
The six application buttons are located on the upper
right-hand side of a vertically-oriented system. Five of the
buttons have secondary functions. The secondary func-
tions are activated by pressing the Function (Fn) button
while pressing the application button.
Ctl-Alt-Del
The buttons also have separate tertiary functions that can
be used while the system is booting up. For more infor-
mation about the tertiary functions, refer to Table 1-4 on
page 16.
EMail
Orientation
Escape
Ctl-Alt-Del is the only application button
that can be used while the system is
logging on or when the system is locked
(i.e., when you have the Logon or
Computer Locked window showing on
your desktop).
Enter
Function
Figure 1-8. Application Buttons
Tablet Icon
Button Icon
and Name
Primary)
(Fn +
Button)
(Secondary)
Description
Pressing the Ctl-Alt-Del button for approximately one second allows you
to log on after boot or after resuming from power management. Holding
the button down for approximately two seconds causes it to act as if Ctl-
Alt-Del had actually been entered from a keyboard.
Security Button: All five buttons are used when implementing security
functions. Four of the buttons are used to enter the password, and the fifth
is used as an Enter button. See “Security Functions of Application Buttons”
on page 17.
Security
Button
Ctl-Alt-Del
Button
When you press the EMail button, you automatically launch Microsoft
Outlook Express, where you can read, create, and send emails.
When you press the Fn + EMail buttons at the same time, you
automatically launch the Web browser. The default page to which you go is
the Fujitsu home page. If you would like to change your home page, go to
the Control Panel-> Internet Options. Select the General tab and enter the
starting address you would like to use.
Internet
Button
EMail
Button
When you press the Orientation button, the system screen orientation
changes from portrait (vertical) to landscape (horizontal) or from landscape
to portrait. When you would like to use the Tablet PC as an eBook, for
example, you would use the portrait orientation, when accessing
spreadsheets, you would more typically use a landscape orientation.
Display
Mode
Button
Orientation
Button
When you press the Fn + Orientation buttons at the same time*, the
display output will switch between internal, external, and simultaneous
display.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
Tablet Icon
Button Icon
and Name
Primary)
(Fn +
Button)
(Secondary)
Description
The Escape application button acts the same way as an Escape key on a
keyboard.
When you press the Fn + Esc buttons at the same time*, they act to invoke
a pre-determined application or generate a combination keystroke, as
assigned in the Tablet Button Settings utility. (You can change the settings
in Control Panel -> Tablet Button Settings).
Escape
Button
Application
A Button
By default, pressing the Fn + Esc combination acts the same as if you had
pressed Ctl + Esc on a keyboard: the Start menu is launched.
The Enter application button acts the same way as an Enter key on a
keyboard.
Pressing the Fn + Ent buttons at the same time*, acts to invoke a pre-
determined application or keystroke combination, as assigned in the Tablet
Button Settings utility. (You can change the settings in Control Panel ->
Tablet Button Settings).
Application
B Button
Enter Button
By default, pressing the Fn + Ent combination acts the same as if you had
pressed Alt on a keyboard: it selects a main menu in the typical Windows
application.
The Function button works in conjunction with the other application
buttons to provide additional functionality for the buttons. Refer to specific
details above.*
Fujitsu
Menu
Utility
Pressing the Fn button twice in succession (within the “sticky” time*),
causes the Fujitsu menu to appear on your screen, allowing you to modify
certain system settings.
Function
Button
Table 1-2. Application Buttons - Primary and Secondary Functions
* The Fn button has a handy “sticky” feature that allows you to press two buttons in immediate succession, rather
than at exactly the same time. After pressing the Fn button, you have a short time (2 to 3 seconds) to press the
second button.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
NAVIGATION BUTTONS
The two navigation buttons are located on the lower
right-hand side of a vertically-oriented system. Each of
the buttons can be toggled by pressing either end of the
button.
The buttons have dual functions. The secondary func-
tions are activated by pressing the Function (Fn) button
while pressing the application button*.
The buttons also have separate tertiary functions that can
be used while the system is booting up. For more infor-
mation about the tertiary functions, refer to Table 1-4 on
page 16.
Navigation Buttons
Ctl-Alt-Del is the only Application button
that can be used while the system is
logging on or when the system is locked
(i.e., when you have the Logon or
Computer Locked window showing on
your desktop).
Figure 1-9. Navigation Button Location
Buttons/icons
Purpose (when pressed alone)
(“Primary” function)
Purpose (when pressed with Fn button)
(“Secondary” function)
This button consists of Page Up and
Page Down segments. When the
Page Up portion is pressed, you will
scroll up one page.
When pressed with the Function (Fn) button*,
the Up portion of this button allows you to tab
right.
When pressed with the Function (Fn) button*,
the Down portion of this button allows you to
tab left.
When the Page Down portion is
pressed, you will scroll down one
page.
This button consists of Up and Down
segments. When the Up portion is
pressed, the cursor will move up.
When pressed with the Function (Fn) button*,
the Up portion of this button will move the
cursor to the right.
When the Down portion is pressed,
the cursor will move down.
When pressed with the Function (Fn) button*,
the Down portion of this button will move the
cursor to the left.
* The Fn button has a handy “sticky” feature that allows you to press two buttons in immediate succession, rather
than at exactly the same time. After pressing the Fn button, you have a short time (2 to 3 seconds) to press the
second button.
Table 1-3. Navigation Buttons
15
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
TERTIARY FUNCTIONS OF APPLICATION AND NAVIGATION BUTTONS
While you are booting up your system, the Application
Buttons and Navigation buttons can be used for entering
and navigating through the Basic Input-Output System
(BIOS), and for invoking the Advanced Options Menu,
where you can enter different modes (such as Safe
Mode).
operating system from disk. Information from the BIOS
is transferred to the operating system to provide it with
information on the configuration and status of the hard-
ware.
The system is booting up while the Fujitsu logo is
displayed immediately after turning on the system. The
table below indicates how the buttons act while the
system is booting up and while you are in the BIOS.
The BIOS is a program and a set of parameters that are
stored in ROM, which tests and operates your Tablet PC
from when you turn it on until it loads your installed
Buttons/icons
Purpose (when pressed while the system is booting up)
Pressing the Ctl-Alt-Del button while the system is booting up takes you into BIOS setup. This is
the same as if you had tapped [F2] on a keyboard.
Ctl-Alt-Del Button
Pressing the EMail button while the system is booting up opens the Boot Options menu. This is
the same as if you had tapped [F12] on a keyboard.
EMail Button
Pressing the Orientation button while the BIOS setup screen is open causes the selected item (if
applicable) to change to the next item. Pressing this is the same as tapping the spacebar on a
keyboard.
Orientation Button
Escape Button
Enter Button
Pressing the Esc button while the BIOS is open acts to escape from the BIOS. This is the same as if
you had tapped [Esc] on a keyboard.
Pressing the Ent button while the BIOS is open acts the same as the [Ent] button on a keyboard.
Pressing the Fn button while the system is displaying the operating system boot menu, opens the
Advanced Operating System Options menu. This menu allows you to enter different operating
system modes (such as Safe Mode). Pressing this button is the same as if you had tapped [F8] on
a keyboard.
Function Button
Pressing the top half of the upper navigation button while the BIOS setup screen is open causes
the cursor in the BIOS setup screen to move up. This is the same as if you had tapped Arrow Up
on a keyboard. This feature is also functional in the operating system boot menu.
Pressing the bottom half of the upper navigation button while the BIOS setup screen is open
causes the cursor in the BIOS setup screen to move down. This is the same as if you had tapped
Arrow Down on a keyboard. This feature is also functional in the operating system boot menu.
Pressing the top half of the lower navigation button while the BIOS setup screen is open causes
the cursor in the BIOS setup screen to move right. This is the same as if you had tapped Arrow
Right on a keyboard.
Pressing the bottom half of the lower navigation button while the BIOS setup screen is open
causes the cursor in the BIOS setup screen to move left. This is the same as if you had tapped
Arrow Left on a keyboard.
Table 1-4. Tertiary Functions of Application and Navigation Buttons
16
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
SECURITY FUNCTIONS OF APPLICATION BUTTONS
Five buttons are used when implementing security functions. Four of the buttons are used to enter the password, and
the fifth is used as an Enter button. Instructions for using the security feature follow the table.
Button Icons
Security Icons
Security Purpose
Security Enter Button
Ctl-Alt-Del Button
Security Button 1
Security Button 2
1
2
EMail Button
Orientation Button
Escape Button
Enter Button
Security Button 3
Security Button 4
3
4
Table 1-5. Security Functions of Application Buttons
The following are examples of valid button strokes:
SETTING UP THE SECURITY PANEL
When you receive your Tablet PC, the security panel
application is pre-installed without any passwords. The
following sections provide detailed information on your
security panel, how to set, change or remove passwords.
■
Pushing [4] by itself
Pushing [2] and [3] at the same time
Pushing [1], [2], and [4] at the same time
Pushing [1], [2], [3], and [4] at the same time
■
■
■
The following are valid passwords. The numbers within
braces ({ }) are button strokes using more than one
button.
Numbered Buttons
Use these buttons to enter your password.(Figure 1-5)
■
{[2]+[3]}, [1], [Enter]
[4], [enter]
{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]
Enter Button
After entering the button strokes, push this button to
enter the password into the Tablet PC. (Figure 1-5)
■
■
Setting Passwords
PASSWORDS
When shipped from the factory, no passwords are set.
You have a choice of having no password or setting a
supervisor and user password. You must set the super-
visor password before the user password.
The user and supervisor password may be set on this
Tablet PC. A supervisor password is typically the same for
all Tablet PC’s and notebooks in a work group, office, or
company to allow for system management. Individual
computers in a group environment should not use a
common password. A password consists of one to five
button strokes plus the enter button. A valid stroke
consists of pushing one or up to four buttons simulta-
neously.
■
The purpose of supervisor password is to
be able to bypass the user password in
case the user password is forgotten. The
supervisor password alone will not lock
the system.
■
You must set the supervisor and user
passwords for the security panel to work.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
Setting Supervisor Password
is entered or an invalid password is entered while the
system beeps, the system will return to its previous
locked state (standby or off) and the Security Indicator
will go off. To reactivate the Tablet PC after a password
failure, you must press the Suspend/Resume button,
then enter a correct password.
You must have set a supervisor password before setting
any user passwords. The supervisor password can bypass
the user password.
1. Go to the Start menu.
2. Click on Run.
3. Type in:
Remember the user password you specified
on the Security Panel Application. If you
forget the password you will not be able to
use your computer. The supervisor pass-
word can override the user password.
C:\Program Files\Fujitsu\Security
Panel Application\Supervisor\
FJSECS.EXE, then press [Enter]
4. Follow the on-screen instructions to set the
Supervisor password.
PRECAUTIONS
Setting User Password
1
Go to the Start menu.
Low Battery Operations
2. Click on All Programs.
If your Tablet PC has a low battery, pushing the suspend/
resume button does not unlock the Tablet PC. To resume
normal operation, first attach a power supply to the
system. Then you may unlock the Tablet PC.
3. Click on Security Panel Application -> Security
Panel Application.
4. Follow the on-screen instructions to set the
user password.
UNINSTALLING THE SECURITY
PANEL APPLICATION
You have two options when uninstalling the security
You may change or remove the supervisor
or user password by repeating the steps
defined above.
panel application:
■
Remove passwords and uninstall the security panel
application software. This will disable all security
features.
Uninstall the security panel application with password
still active. This will not allow any changes to the
password.
USING YOUR SECURITY PANEL
■
The security lock feature is in effect both when the system
resumes from Off, Standby, or Hibernation state. You
always need to push the Security Panel buttons to input
the user password. Your system will not begin the boot
sequence until you enter your supervisor/user password.
Uninstalling the Security Panel
Application Software
Remove passwords when User wants no password
protection whatsoever and doesn’t want to give anybody
the utility to set a password on their computer. In this
case, if passwords (supervisor, user, or both) are set, the
passwords must first be cleared BEFORE removing the
application. To clear passwords, follow same procedure
in SETTING PASSWORD CODES except this time,
select REMOVE, enter current password then click Next.
When asked to confirm select Yes.
From Off State
1. Turn on your system.
2. When the Security Indicator flashes, enter the pass-
word and press Enter button.
For example, if the password is 22222, first press
Button 2 five times and press the Enter button. The
Tablet PC will boot to normal operation.
From Standby/Hibernation State
1. Press your Suspend/Resume button.
Removing Security Panel Application with
Passwords Still Active
Using this feature will not allow any changes to
2. When the Security Indicator flashes, enter the pass-
word and press Enter button.
The Tablet PC should resume normal operation.
the password.
Incorrect Password Entry
Removing the applications does not remove
the password. It simply removes the utility
to change/add/remove passwords. To
change your password you must reinstall
the application.
If an invalid supervisor or user password is entered three
times in succession, the system will “beep” for about one
minute. If a valid password is entered within a minute
(while system beeps), the beeping will stop and the
Tablet PC will resume normal operation. If no password
18
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
User:
1. Go to Start Menu. Click on Control Panel.
ClickMe!
INSTALLING CLICK ME!
2. Open Add or Remove Programs (In Vista: Programs
and Features) in the Control Panel.
Before installing the ClickMe! utility, be
sure the wireless LAN switch is turned on.
3. Select the Security Panel Application (In Vista: Secu-
rity Panel) in the list, and click Add/Remove.
4. When the Confirm File Deletion box appears, click
Yes.
Windows Vista Systems
Supervisor:
The first time you boot up your system, you will see a
“Primary Settings for the PC” window. This window
explains the installations which will be performed by the
Click Me! utility. If you click [Execute], Click Me! will
begin installing. If after clicking the button you receive a
“User Account Control” window, you will be asked for
your permission to continue. Click [Yes] to continue. If
you cancel the operation, the Click Me! icon will appear
on your desktop for later installation.
1. Go to Start Menu, Click on Control Panel.
2. Open Add or Remove Programs (In Vista: Programs
and Features) in the Control Panel.
3. Select the Security Panel Application for Supervisor
(In Vista: Security Panel for Supervisor) in the list,
and click Add/Remove (In Vista: Uninstall).
4. When the Confirm File Deletion box appears, click
Yes.
Windows XP Systems
Reinstalling the Security Panel Application
To reinstall supervisor or user security application, you
will need your Drivers and Applications CD. The
Utilities\Security Panel Application folder contains two
separate folders: Supervisor and User. The setup files for
supervisor and user security applications are contained
in those folders.
The first time you boot up your system, you will see an
icon called Click Me! in the Start menu. We highly
recommend that you install the ClickMe! utility the first
time you boot up. When you click the Click Me! icon,
your system will automatically build the icon tray in the
bottom right of the screen. These icons provide links to
utilities that you will frequently access., such as wireless
LAN software provided by the wireless LAN manufac-
turer.
1. Go to the Utilities\Security Panel Application\
Supervisor folder on the CD and double-click the
setup.exe file. The Installing Security Panel Applica-
tion window will appear. Follow the instructions on
the screen.
There may be additional third-party
applications that are not installed by the
ClickMe! utility. For more information,
refer to your Getting Started Guide.
2. Go to the Utilities\Security Panel Application\User
folder on the CD and double-click the setup.exe file.
The Installing Security Panel Application window
will appear. Follow the instructions on the screen.
Supervisor and user passwords can be set via Windows
software using the FJSECS.exe and FJSECU.exe files,
respectively. FJSECU.exe for the user password cannot
run without first setting a supervisor password. You need
to run FJSECS.exe first to set the supervisor password.
Follow instructions under Setting Passwords on page 17.
FUJITSU DRIVER UPDATE UTILITY
Your system has a convenient tool called the Fujitsu
Driver Update (FDU) utility. With FDU, you can choose
to automatically or manually go to the Fujitsu site to
check for new updates for your system. For more infor-
mation about the FDU utility, refer to “Automatically
Downloading Driver Updates” on page 83.
If you forget both passwords, please contact Fujitsu
Computer Systems Corporation Service and Support at
1-800-8Fujitsu (1-800-838-5487). Fujitsu Computer
Systems Corporation charges a service fee for unlocking a
password-restricted Tablet PC. When calling please have
a valid credit card and provide proof of ownership. You
will then be given instructions on where to ship your
Tablet PC.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
CONNECTORS AND PERIPHERAL INTERFACES
Connectors and peripheral interfaces on the Stylistic
ST5100 Series Tablet PC allow the connection of a
variety of devices. Specific locations are illustrated in
Figures 1-2 through 1-5.
Table 1-6 provides a description of each peripheral
connector on the Stylistic ST5100 Series Tablet PC. Each
of the illustrated icons is either molded into or printed
on the Tablet PC chassis.
Connector/
Peripheral
Tablet PC
Icon
Purpose
DC input
connector
Connect an external power source such as the AC adapter or auto/airline
adapter.
USB Port
Connect Universal Serial Bus 2.0 compliant devices to the Tablet PC.
PCMCIA
Card slot
Insert a Type I or Type II PC Card.
SD Card/
Memory Stick
slot
Insert a Secure Digital (SD) Card or a Memory Stick.
Microphone jack
Connect an external microphone. The internal microphone is disabled when you
plug in an external microphone.
Headphone jack
IrDA/FIR port
Connect stereo headphones or powered external speakers. The internal speaker
is disabled when you plug in external headphones or powered speakers.
An infrared transceiver built into the Tablet PC allows you to communicate with
other devices that are compliant with the IrDA Standard Rev. 1.1. Effective range
for infrared communication is about 3 feet, and within 15 degrees off center. A
clear line-of-sight path must exist between the IrDA port on the Tablet PC and
the IrDA transceiver on the other device.
Modem
Connect a telephone line to the optional internal modem using a standard RJ-11
telephone plug.
Tablet Dock port
Connect the Stylistic ST5100 Series Tablet Dock or other approved docking
device. Refer to documentation accompanying the docking device for more
information.
Infrared
keyboard/
mouse port
An infrared receiver built into the Tablet PC allows you to communicate with a
Fujitsu wireless infrared keyboard or mouse. The keyboard infrared port works
optimally when it is placed between 10 to 30 cm (approximately 4 in. to 12 in.)
from the keyboard infrared port (which is located on the bottom edge of the
Tablet PC). Ensure there is a clear line-of-sight path between the infrared receiver
on the Tablet PC and the infrared transmitter on the keyboard or mouse. Note
that an infrared keyboard or mouse works best when the system is in landscape
orientation.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
Connector/
Peripheral
Tablet PC
Icon
Purpose
Lock slot
The security slot allows you to secure the Tablet PC using compatible locking
devices.
IEEE 1394 jack
The IEEE 1394 jack allows you to connect IEEE 1394 (Firewire) devices such as
digital video cameras and external hard drives to your Tablet PC.
Suspend/Resume
button
The Suspend/Resume/Power On button allows you to suspend Tablet PC
activity without powering off, resume your Tablet PC from standby mode, and
power on the system when it has been shut down from Windows.
Page Up/
Page Down
The Page Up/Page Down button allows you to navigate quickly from page to
page without scrolling.
Local Area
Network (LAN)
The LAN (RJ-45) jack is used to connect the internal 10/100/1000* Base-T/Tx
Ethernet to a Local Area Network (LAN) in your office or home, or broadband
devices such as a cable modem, DSL, or satellite internet.
*1000 Mbps, commonly referred to as Gigabit Ethernet.
Battery Release
Latch
The battery release latch allows you to remove the battery from your system for
storage or replacement.
Wireless LAN/
Bluetooth
The wireless LAN/Bluetooth switch allows you to turn power to the optional
wireless LAN or Bluetooth devices on and off.
On-Off Switch
FingerprintSwipe
Sensor
The optional fingerprint swipe sensor allows you to avoid having to enter a user
name and password every time you want to log into the system. This icon
indicates the direction in which you should swipe your finger.
Table 1-6. Peripheral Connectors/Interfaces
21
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n O n e
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Using Your
Stylistic Tablet PC
23
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T w o
24
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
Using the Stylistic ST5100 Series Tablet PC
This chapter covers the fundamental concepts, basic
system operation and use, and system functions of the
Stylistic ST5100 Series Tablet PC. You should familiarize
yourself with this information before you attempt to
operate the system.
power. Power to memory is on, maintaining data in
programs that were running before system operation
was suspended. The system does not respond to the
pen or other input when in Standby mode. Refer to
the “Resuming System Operation” section later in this
chapter for information on returning the system to
the On state.
Prior to using your system, be sure to fully
charge the battery if you plan to run on
battery power. Failure to do so may result
in erratic performance.
•
Hibernate mode (S4): System operation is
suspended. All system functions are turned off to
conserve power. Active data in programs that were
running before suspending system operation is stored
on the hard disk drive. The system does not respond
to the pen or other input. Refer to the “Resuming
System Operation” section later in this chapter for
information on returning the system to the On state.
SYSTEM STATES
Before you begin using your Tablet PC, review the
different system states (or modes) that the system can
use. Being familiar with these states will help you deter-
mine whether it is appropriate to turn on, resume,
standby, hibernate or shut down the system when you
begin or end a session. System behavior for each system
state is described briefly in the following, with each
system state listed in decreasing order of power usage:
•
Off state: All system functions are turned off to
conserve power. The system does not respond to the
pen or other input. The system boots at the next
system power-on.
•
On state: The system is running and the display
screen is on.
The system consumes the same amount of
power whether it is in Hibernate mode or
the Off state.
•
Idle state: Some system functions are regulated or
turned off to conserve power. The display screen may
be turned off. The system returns to the On state
when pen activity or other input is detected.
Your system may be configured to enter some of these
states automatically after a period of inactivity to
conserve battery power.
•
Standby mode (S3): System operation is suspended.
Most system functions are turned off to conserve
To Change State*
Icon Appearance
Current State
On State or
Idle State
To enter Off state, shut down the system using the Start menu on your system.
Power icon
displayed
continuously
To enter Standby or Hibernate† state, suspend system operation using either a
hardware or software suspend.
Standby†
Power icon blinking
To enter the On state, resume system operation by pressing the Suspend/
Resume button.
To enter the Off state, resume system by pressing the Suspend/Resume
button, then shut down your system.
Power icon not
displayed
Off State, or,
Hibernate
To enter the On state, start your system, or resume system operation by
pressing the Suspend/Resume button.
Table 2-1 Changing System States
* Information in Table 2-1 is supplied to help you understand which system states your system can enter from the current
system state. Refer to the procedures on starting the system, shutting down the system, suspending system operation, and
resuming system operation given later in this chapter.
†
Your system may be configured to use either Standby mode or Hibernate mode.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T w o
When you use your Tablet PC, you can change the
current system state in a number of ways, depending on
the system’s current state. To determine the current
system state, observe the Power icon in the Status
display. Table 2-1 on page 25 gives the different system
states represented by the Power icon and describes how
you can change the system state from the current state.
In order to ensure that you receive the most benefits
from the Windows Vista operating system, it should be
registered the first time you use it.
1. First of all, you will need to read and accept the End
User License Agreements (EULAs).
• If you reject the terms of the license
agreements you will be asked to
review the license agreements for
information on returning Windows or
to shut down your Tablet PC.
POWERING UP THE TABLET PC
Follow the procedure below to start your Tablet PC.
Before you begin, confirm that the system is in the Off
state. To do so, observe the Status display. If the Power
icon is not visible in the Status display, the system is in
Off state or in Hibernate mode and it is safe to perform
this procedure. If the Power icon is visible (either
blinking or on continuously), do not perform this
procedure. See “System States” earlier in this chapter for
details on modes represented by the Power icon.
• You cannot use your tablet until you
have accepted the License
Agreements. If you stop the process
your tablet will return to the beginning
of the Windows Welcome Process,
even if you shut your tablet down and
start it up again..
1. Ensure that the battery in your Tablet PC is
sufficiently charged, or connect an external power
source such as the AC adapter or auto adapter to
your Tablet PC.
2. You will be prompted to enter your User Name and
Password and you will be given a chance to select an
icon for your account.
3. The next screen asks for a Computer Name and
allows you to choose a desktop background.
2. Press the Power On/Suspend/Resume button to start
the system.
4. You will next see a "Help protect Windows automat-
ically" screen in which the default choice is "Use
recommended settings”. The other two choices are
"Install important updates only" and "Ask me later".
Select from the three choices.
After performing initialization, the system starts the
operating system installed on the hard disk drive. Once
the operating system is running, you can use the system.
BOOTING THE SYSTEM THE FIRST TIME
We strongly recommend that you not attach any external
devices until you have gone through the initial power on
sequence.
5. On the next screen set your time and date settings.
6. You will next see the "Select your computer's current
location" screen. Make your selection from Home,
Work (Default), and Public location.
When you turn on your tablet for the first time, it will
display a Fujitsu logo on the screen. If you do nothing
the system will load the operating system, and then the
Windows Welcome will begin.
7. The "Thank you" screen follows and an offer for free
Norton Internet Security is extended. Following are
several screens while Windows checks the system
performance.
Depending upon your operating system (Windows Vista
or XP edition), there is a different procedure for stating
your system for the first time, as outlined below.
8. Windows will then boot up for the first time. After
the first boot, press [Execute] to install the Primary
Settings. This will take several minutes.
9. After the Primary Settings are installed, reboot the
system again.
Starting Windows Vista the first time
The first time you initialize your Windows
Vista system, the screen will be blank for
approximately two minutes. This is
normal. After initialization, a “Set Up
Windows” dialog box will appear.
Registering Windows Vista with Microsoft
1. After Windows has booted up for the first time, the
Control Panel Welcome Center will appear. If the
Register Windows Online icon is not seen in the
window, click on “Show all xx items” (where “xx” is
the number of topics in the Welcome Center).
Important: During the setup procedure, do
not disconnect the power supply, press any
buttons, or use any peripheral devices such
as a mouse, keyboard, or remote control.
2. Click on Register Windows Online and follow the
instructions that appear to register your copy of
Windows.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
Registering Windows XP with Microsoft
In order to ensure that you receive the most benefits from
the Windows operating system, it should be registered
the first time you use it.
SHUTTING DOWN THE SYSTEM
Follow these steps to shut down/turn off your system:
1. If system operation has been suspended, resume
system operation. See “Resuming System Operation”
later in this chapter for details.
After you receive the Windows Welcome screen, you will
be prompted to enter registration information in the
following order.
2. Save your work and close all running programs.
3. Choose Shut Down from the Windows Start menu.
4. Carry out the Shut Down command.
First of all, you will need to read and accept the End User
License Agreements (EULAs). After accepting the EULAs,
you will be asked if you want to enable the Automatic
Updates feature. Acceptance of this feature is recom-
mended because it allows your system to be updated
automatically whenever an important change becomes
available for your tablet.
The system is now in the Off state.
SUSPENDING SYSTEM OPERATION
The Tablet PC allows you to suspend the system opera-
tion without closing programs or exiting the operating
system. Use this feature to conserve battery power when a
system shutdown is not practical or when the battery
needs to be changed.
• If you reject the terms of the license
agreements you will be asked to review
the license agreements for information
on returning Windows or to shut down
your tablet.
If you have set your system to turn power
off from the Power Options utility in the
Control Panel, the following procedure will
not be possible, since pressing the button
shuts the system down rather than
suspending it. To change your power
options, go to Start -> Settings -> Control
Panel -> Power Options.
• You cannot use your tablet until you
have accepted the License Agreements.
If you stop the process your tablet will
return to the beginning of the Windows
Welcome Process, even if you shut your
tablet down and start it up again.
To suspend system operation:
Several additional windows will appear, prompting you
to enter a name and description for your computer, an
Administrator password, and a domain name. Read the
instructions on the screens carefully and fill in the infor-
mation as directed.
1. Press the Suspend/Resume button, or carry out the
Standby command from your operating system or
power management program. (If your system is
configured to suspend operation using Hibernate
mode, which is explained later in this procedure, a
message is displayed while data is saved to your hard
disk.)
You will then be automatically connected to the Internet,
if you have an appropriate connection available. If an
automatic connection is not possible, you will be asked
about how you dial out from where you will be using
your tablet. If you are not connected to a phone line and
plan to register at a later time, you may click the Skip
button.
If you are replacing the battery, wait until
system operation is suspended and the
power icon is flashing before you remove
the battery. Failure to do so could result in
loss of your unsaved data. (Note that if the
Resume On LAN function is enabled in the
BIOS setup, you should not remove the
battery unless the system is shut down.
When Resume ON LAN is enabled, the
bridge battery is disabled in order to
optimize battery life.)
Once you are connected to the Internet, you will be asked
if you wish to continue with the registration. If you select
Yes you will then enter your name and address, and email
address if desired. Click Next to complete registration.
REGISTERING YOUR STYLISTIC
TABLET PC WITH FUJITSU
You can register your tablet by going to our website at:
us.fujitsu.com/computers
2. The Power icon either flashes (Standby) or is not
displayed (Hibernate) when system operation is
suspended, depending on how your system is config-
ured. At this point, programs that were running are
stopped, active data is saved, and the system enters
one of two different low-power states, or standby
modes, as explained in the following paragraphs.
You will need to be set up with an Internet Service
Provider (ISP) to register online.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T w o
3. Observe the Power icon in the Status display to
determine which suspend mode your system is
using.
power source such as the AC adapter before you can
resume system operation. (If the charge drops to a
Critically Low level while the system is in Standby
mode, the system stays in that mode until power is
restored or totally dissipated.)
■
Power icon is blinking: Standby mode.
In this mode, active data is saved by maintaining
power to RAM while most other system components
are powered off. The Battery Gauge icon in the Status
display indicates the battery charge level.
■
Suspending system operation interrupts data commu-
nications; therefore, some programs may block the
system from suspending to prevent an interruption.
■
The suspend action of the Suspend/Resume button
may be disabled to prevent accidental interruption. If
this is the case, pressing the Suspend/Resume button
will not suspend system operation as described here.
(In this case, standby mode can only be achieved using
the system software). Contact your local help desk or
reseller if your system configuration is not suitable.
■
Power icon is not displayed: Hibernate mode.
In this mode, active data is stored on the hard disk
drive and power usage is reduced to the same level
used in the Off state. When the system is in Hibernate
mode, the Battery Gauge icon is not visible in the
Status display. In this mode, there is no danger of
losing data if battery power is lost.
■
If your system is equipped with a PC Card that allows
you to connect to a wired or wireless network, you
may be logged off the network after a period of inac-
tivity while system operation is suspended. Contact
your network administrator or help desk, or call
Fujitsu Service and Support at 1-800-8Fujitsu (1-800-
838-5487) for details on your network log-off parame-
ters.
If you have successfully performed this procedure,
system operation is now suspended. Refer to
“Resuming System Operation” later in this chapter to
resume system operation. Also, note the following
with regard to suspending system operation:
■
You can remove the battery while the system is in
Standby or Hibernate modes in order to install a
charged battery. To prevent losing unsaved data, wait
until system operation has suspended before you
remove the battery. Note that after you remove the
battery, you have approximately five minutes to
replace it with a new battery or to plug in a power
supply before the bridge battery is depleted.
RESUMING SYSTEM OPERATION
To resume operation from either Standby or Hibernate
modes, press the Suspend/Resume button.
■
From Standby mode
Status lights indicate that the system state is changing.
It may take up to a minute before the system returns to
the On state and system operation resumes. Note that
the display turns on shortly before the pen becomes
active due to the power-up sequences observed by the
system.
■
■
Your system may be configured to suspend operation
automatically after a period of inactivity.
Your system may be configured to enter Hibernate
mode automatically after a period of time in Standby
mode.
■
From Hibernate mode
Active data is read from the hard disk drive, and the
system returns to the On state after a short time.
■
The system uses a small amount of battery power
when in Standby mode. Eventually, the battery will
become fully discharged.
Note that power to several system
components must be restored before
system operation resumes. Allow sufficient
time for system operation to resume
before attempting to use the system. If
your system uses Hibernate mode, it will
take longer to resume operation as
compared to using Standby mode. Time is
needed to read data from the hard disk
drive.
If you will not be using the system for an
extended period, shut down the system
rather than using Standby mode.
■
If the battery charge drops to a Low-Battery Warning
level while the system is running, the system will beep
periodically. If this occurs, suspend system operation,
shut down the system, or attach an external power
source, such as the AC adapter, to the Tablet PC.
Use the system as you normally would once system oper-
ation resumes.
■
If the battery charge drops to a Critically Low level
while the system is running, the system is forced into a
Standby or Hibernate mode. If this occurs, you must
either install a charged battery, or connect an external
All programs resume at the point where execution
stopped when system operation was suspended.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
[Calibrate Now]
USING THE SHOCK SENSOR UTILITY
The calibration is executed. Please position the computer
as horizontally as possible, then click the [Calibrate Now]
button. The current horizontal position will be recog-
nized as the true horizontal by performing the calibra-
tion.
The Shock Sensor Utility is designed to decrease the risk
of damage to the computer's hard disk drive (HDD) in
the event of excessive impact or vibration. The Shock
Sensor Utility also has the ability to improve the security
of the computer by automatically locking the computer
with a password when it is carried. Note that the HDD
protection and computer locking features are mutually
exclusive; both cannot be selected at the same time.
3. Click the [OK] or [Cancel] button. The [Setup]
window closes.
Using the Shock Sensor Monitor Window
Right-click the Shock Sensor Utility icon in the system
tray at the bottom-right of the screen, and select
[Monitor] from the menu. The Monitor window appears.
■
Shock Sensor Utility does not completely
protect the HDD and does not provide
absolute security for the computer.
■
Note that the Monitor is designed for entertainment, and
has no effect on system settings or orientation. To navi-
gate the monitor, use the buttons described below.
The computer may stop temporarily while
the HDD head is retracted. To restart the
computer, keep the system horizontal.
■
Advance. Incline the display to the hinge side, or use
1. Double-click the Shock Sensor Utility icon in the
system tray at the bottom-right of the screen. The
[Shock Sensor Utility] window appears.
[Up] key.
■
Back. Incline the display to the mouse-button side, or
use [Down] key.
Right. Incline the display to the right side, or use
[Right] key.
Left. Incline the display to the left side, or use [Left]
key.
Go up. Use [A] key.
Go down. Use [Z] key.
Close. Use [Esc] key.
■
2. Click the red [Setting] button. The [Shock Sensor
Utility Settings] window appears.
■
Action
Select the action you wish this utility to perform:
■
■
Protect HDD from impact. HDD head is retracted
■
■
when an impact to the computer is detected.
Lock computer when carried. Lock the computer
■
when it is being carried.
Nothing. No action.
ADJUSTING THE DISPLAY BRIGHTNESS
There are four ways to adjust your display’s brightness:
■
Sensitivity of impact/horizontal move/fall/carry
detection
Adjust the sensitivity of the acceleration sensor based on
Depending upon whether you are running
your system on battery or AC power, the
default screen brightness settings will be
different. The screen brightness default for
running on battery is lower than that on
AC power in order to optimize battery life.
system motion or impact.
Ignore periodic vibration.
If vibration is periodic, disregard it.
Ignore mouse click
When the mouse is clicked, sensitivity is temporarily
■
Windows XP Tablet PC: Click the Tablet icon in the sys-
tem tray at the bottom right of the screen. (When the
cursor is on top of the icon, a message stating “Change
tablet and pen settings” is displayed.) When the Tablet
and Pen Settings window appears, select the Display
tab, and move the Screen Brightness slider to change
the brightness.
Windows Vista: Open the Windows Mobility Center
control panel by right-clicking on the Power Options
(battery) icon in the system tray. From there you can
adjust display brightness.
lowered.
Ignore keyboard action
When the keyboard is used, sensitivity is temporarily
lowered.
Confirm calibration when user logs on
Select [Confirm calibration when user logs on] if you
want to recognize the current orientation as horizontal at
logon.
Perform calibration automatically when user logs on
Select [Perform calibration automatically when user logs
on] if the system is normally used on a horizontal
surface.
■
Click Start -> Control Panel -> Tablet and Pen Settings.
Select the Display tab, and move the Screen Brightness
slider to change the brightness.
■
Click the Fujitsu Menu icon in the system tray at the
bottom right of the screen. (When the cursor is on top
of the icon, a message stating “Fujitsu Menu...” is dis-
29
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T w o
played.) Select Tablet and Pen Settings and select the
Display tab. Move the Screen Brightness slider to
change the brightness.
(closest to the pen tip) barrel button switch corresponds
to the right mouse button (when used in combination
with the tip switch). The rear toggle of the barrel button
switch and the eraser switch at the end of the barrel act
as electronic ink “erasers”.
■
Press the Fn key twice to invoke the Fujitsu menu and
select Tablet and Pen Settings.
The rear toggle, eraser, and tip click pressures can be
changed by clicking [Start] -> Control Panel, and
double-clicking the Fujitsu Pen Settings (XP) or Pen and
Input Devices (Vista) icon. Note that the rear toggle
switch and the eraser switch are both affected by the
same settings; they cannot be changed individually.
USING THE PEN
You can use the Stylistic ST5100 Series pen to generate
and create electronic “ink”, to select items, and to navi-
gate through programs on the Tablet PC. Programs that
support handwriting recognition also allow you to write
characters directly on the screen with the pen. You can
also use the pen as a drawing tool.
To change the rear toggle and eraser button function,
select the drop-down list to select a new function, then
click [Apply]. If you don’t want the rear toggle and
button switch to have any function, select Ignore from
the list.
Eraser Switches
Barrel Switch
Adjusting the click pressure determines how much pres-
sure must be put on the pen tip in order for the screen to
react. The softer it is set, the less pressure required; the
harder it is set, the more pressure required. To change
the click pressure, use the slider bar to make the click
pressure harder or softer, then click [Apply].
Tip Switch
Pen Tether Attachment Point
• Ensure that a screen protector is installed
on the Tablet PC screen before you use
the pen. The warranty does not cover a
scratched screen.
Figure 2-1. Stylistic ST5100 Series Pen
The Stylistic ST5100 pen is a sophisticated,
high-quality electronic instrument that can
be damaged if used improperly. Treat the
pen as you would any precision device.
The following list contains guidelines for
proper pen handling:
• Use only the pen provided with your
Tablet PC. Do not use substitutes that
were not designed for the Stylistic
ST5100 Series Tablet PC.
Here are some hints that may help you use the pen more
effectively:
• Do not use the pen as a pointer or tap it
on surfaces other than the Tablet PC
screen.
•
To activate the tip switch, tap or hold the pen tip
against the screen.
• Do not try to turn the thumb grip on
the pen; it is designed for inserting and
removing the pen from the pen holder
and for attaching a pen tether.
•
To activate the barrel button switch, press and hold
the end of the button you wish to use (front toggle is
the right mouse button switch; the rear toggle acts as
an electronic “eraser”).
• Never store the pen with the tip bearing
the weight of the pen (e.g., sitting tip
down in a pencil cup). Storing the pen
tip down could distort the internal
mechanism over a period of time
(especially in higher temperatures),
causing the tip to act as if it is always
depressed. To avoid damage, the pen
should be stored in the pen holder
when not in use.
•
•
To move the cursor, hold the pen tip within 1/8 inch
(3 - 5mm) from the screen and move the pen.
To start a program, double-tap the pen tip (tap the
pen tip twice rapidly) on the program icon as you
would double-click a mouse.
•
•
•
To select an object, tap the pen tip on the object
once.
The screen reacts when the pen tip is approximately 1/8
inch (3-5 mm) from the screen. The pen has four
switches: a tip switch, a barrel button toggle switch with
switches at both ends, and an "eraser" switch, located on
the end of the barrel. By default, the tip switch corre-
sponds to the left mouse button, and the front toggle
To “double-click” an object, tap twice on the object
quickly.
To move, or “drag”, an object on the screen, place the
pen tip directly over the object, then as you hold the
pen tip against the screen, move the pen.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
CALIBRATING THE PEN
In order to ensure accurate tracking between the pen and
cursor, you must run the Touch Screen Calibration Utility
before you use the active digitizer for the first time, or
after you change the display resolution.
Gap
To run the calibration utility:
1. Go to Start -> Control Panel and double-click on the
Tablet and Pen Settings icon.
2. Click Calibrate.
Figure 2-3. Tip Removal Tool
3. Adjust the display of your Tablet PC to a comfortable
angle.
To remove the tip, position the tip in the gap between the
two ends of the tool. Pinch the tool together so the tip is
firmly clasped, then pull it from the barrel. If the tip is
worn or damaged, discard it.
4. Using the pen, firmly touch the screen directly on the
(+) symbol; the (+) symbol will move to the next
location.
To replace the tip, retrieve one of the new tips that accom-
panied your pen. Insert the flat end of the tip into the
barrel and push it in firmly until it is seated.
5. Repeat step 4 in the four corners, then click OK.
INSTALLING A PEN TETHER
If you need more tips, they can be ordered from the
Fujitsu website at: us.fujitsu.com/computers.
To prevent dropping or losing your pen, you should
attach it to your system using the pen tether that is
included with the system.
CHARGING THE BATTERY
To attach the pen tether to your Tablet PC, perform the
following steps:
The Stylistic ST5100 Series battery can be charged while it
is installed in the Tablet PC.
1. Attach the end of the pen tether with the smaller loop
to your pen. Do do so, push the end of the tether
through the hole in the pen, then thread the opposite
end of the tether through the loop. (See Figure 2-2.)
To charge the battery:
1. Connect a DC power source, such as the AC adapter,
to the DC input connector on the Tablet PC. The DC
Input icon appears in the Status display. If the battery
charge is below 90%, the battery begins charging and
the Charging icon appears in the Status display. If the
battery charge is 90% or higher when you connect DC
power, the battery will not charge, preventing battery
overcharging.
Pen tether
attachment
point
2. Look at the Battery Charge icon in the Status display
to determine the percent of charge in the battery. See
“Status Display” in Chapter 1 of this manual for a
description of the Battery Charge icon.
Larger loop
Smaller loop
As long as DC power remains connected to the Tablet PC,
the charging process continues until the battery charge
reaches 100%.
Figure 2-2. Installing a Pen Tether
2. Attach the end of the pen tether with the larger loop
to the attachment point on your pen tablet. To do so,
insert the end of the pen tether through the attach-
ment point, then feed the pen through the large loop
in the tether.
Also note the following with respect to charging the
battery:
•
You can use the system, suspend system operation, or
shut down and turn off the system without
interrupting the charging process; however, using the
system while the battery is charging will cause the
battery to charge at a slower rate.
REPLACING THE PEN TIP
With use, the pen tip may become worn or may pick up
foreign particles that can scratch the screen. A damaged
or worn tip may not move freely, causing unpredictable
results when using the pen. If your pen exhibits these
problems, you should replace the pen tip. To do so, use
the pen tip removal tool included with your pen.
•
As noted in the procedure above, the system will not
begin charging the battery if the battery charge level is
90% or higher when the system is initially connected to
external DC power. (This prevents the battery from
being overcharged.)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T w o
•
The battery uses Lithium ion battery cells which have
no “memory effect.” You do not need to discharge
the battery before you begin charging.
Once the battery is installed, you can resume system
operation or start and use your system normally.
TIPS FOR CONSERVING BATTERY POWER
You can extend the charge life of your battery by
conserving battery power. (Your results may vary
depending on your application and how the system is
configured.) Here are some suggestions to help you
conserve battery power:
REMOVING AND INSTALLING THE BATTERY
The battery can be removed from the Tablet PC and
swapped with a charged battery. The battery can then be
charged in an external charger if one is available. To
remove the battery from the Tablet PC:
•
•
•
•
Use an external power source such as the AC adapter
whenever the system is docked.
1. Choose one of the following:
• If a charged battery is available, you can suspend
system operation. A built-in “bridge” battery will
maintain the system in Standby mode for about 5
minutes while the battery is removed; this allows
time for replacement with a charged battery.
Suspend system operation if you know that you
won’t be using the system for a while.
Shut down the system if you won’t be using the
system for an extended period of time.
Switch the wireless LAN switch Off when wireless
LAN functionality in not needed (applicable only for
systems with optional wireless LAN).
• If a charged battery is not available, save your work
and close all running programs, then shut down
the system or Hibernate.
•
Use power management (available from the Power
Options in the Control Panel) to help you conserve
power automatically.
• Plug in an external DC power source.
2. Slide the battery release latch in the direction
indicated. (See Figure 2-4 on page 32 for location).
•
•
Reduce the brightness of the LCD.
3. Pull the battery away from the system, as shown in
the illustration and remove the battery from the
Tablet PC.
Battery life is dependent upon the operating system,
power settings, and applications in use.
If you are using an external battery charger, refer to the
instructions provided with the battery charger.
Operation of the Bridge Battery
When installed in the Tablet PC, the battery provides
power to some system components—even when the
system is in the Off state. When the battery is removed,
power is supplied to these components by a “bridge”
battery that is built into the Tablet PC.
Under Federal, state, or local law, it may
be illegal to dispose of batteries by putting
them in the trash. Be sure to dispose of
batteries in accordance with local
government regulations.
The bridge battery is not designed for long-term opera-
tion. To maintain the bridge battery properly, observe
the following measures:
To install the battery:
1. Orient the battery with the slides in the empty
battery tray. Slide the battery into the tray and press
it firmly until it is seated. When it is properly seated,
the battery release latch should return to position
and lock the battery.
• The bridge battery function is disabled if
Wake On LAN is enabled in the BIOS.
• The system arrives with the bridge
battery in a discharged state. Be sure to
charge it sufficiently before relying upon
it to support the system in the event of
battery removal.
Battery Pack
•
•
•
To prevent draining the bridge battery, always store
the system with a charged battery installed.
If the bridge battery becomes drained, it takes
approximately 8 hours for it to be fully recharged.
The bridge battery charges when the AC Adapter is
connected and the system is in On or Off states or
Standby mode. It charges from the battery only when
the system is in the On state.
Battery Release Latch
Figure 2-4. Removing the Battery
32
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
Inserting Memory Stick/SD Cards
MODEM CONNECTION
Memory Sticks and SD Cards are inserted in the Memory
Stick/SD Card slot (Figure 1-4). To insert a Memory Stick
or SD Card, follow these steps:
The internal 56 Kbps LAN/modem module
installed in the Stylistic ST5100 Series
Tablet PC has actual maximum transfer
rates of 53 Kbps (receive), 33.6 Kbps
(send), and 14.4 Kbps (fax). Download
rates are limited to 53 Kbps in the United
States due to FCC restrictions.
Inserting or removing a Memory Stick or SD
Card during your system’s shutdown or
bootup process may damage the card and/
or your computer.
Do not insert a card into a slot if there is
water or any other substance on the card as
you may permanently damage the card,
your Tablet PC, or both.
The Stylistic ST5100 Series Tablet PC is designed to
accept a standard RJ-11 telephone plug. Connect the plug
to the modem jack located on the left-hand side of the
Tablet PC (See Figure 1-5 on page 9 for location). The tele-
phone plug can be inserted whether or not the Tablet PC
has power applied.
1. See your Memory Stick or SD Card manual for
instructions on the insertion of your card. Some
cards may require that your system is off while
inserting them.
If you need assistance configuring the Stylistic ST5100
Series Tablet PC modem or LAN, contact your local help
desk or reseller.
2. Make sure there is no card currently in the slot. If
there is, see Removing a Memory Stick/SD Card.
MEMORY STICK/SD CARD SLOT
3. Insert your card into the slot with the product label
facing up.
Your Tablet PC supports Memory Stick and SD flash
memory cards on which you can store and transfer data
to and from a variety of digital devices. These cards use
flash memory architecture, which means they don’t need
a power source to retain data.
4. Push the card firmly into the slot until it is seated in
the connector.
Removing A Memory Stick/SD Card
To remove a Memory Stick/SD Card, follow these steps:
Memory Stick is a flash memory technology developed
by Sony Electronics. Memory Stick allows you to record,
transfer and share digital content, such as digital pictures,
movies, music, voice, and computer data and applica-
tions.
See your Memory Stick or SD Card manual
for specific instructions on the removal of
your card. Some cards may require your
computer to be in Standby Mode or Off
while removing them.
Secure Digital (SD) Cards are very similar to Memory
Sticks, but they are shorter. Like the Memory Stick, SD
Cards allow portable storage among a variety of devices,
such as cell phones, GPS systems, digital cameras, and
PDAs. SD Cards transfer data quickly, with low battery
consumption. Like the memory stick, it uses flash
memory architecture.
Push the Memory Stick or SD Card in until it unlatches.
It will then eject from the slot for removal
PC CARD SLOT
The Stylistic ST5100 Series Tablet PC Card slot allows
you to insert a Type I or Type II PCMCIA Card.
Inserting a PC Card
To insert a PC card, position the side with the arrow
facing up (i.e., when looking at the tablet’s display side,
the arrow on the card should be visible.) Slide the card
into the PC Card slot, and press it firmly to ensure proper
seating. (See Figure 2-6 for location)
If you need assistance inserting a PC Card in the Stylistic
ST5100 Series Tablet PC, contact your corporate help
desk or reseller.
Figure 2-5. Memory Stick and Secure Digital Card
33
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T w o
REMOVING AND INSTALLING MEMORY
There are two DIMM slots in your Tablet PC. 256 MB,
512 MB, 1 GB, and 2 GB modules are available, so you
can install a combination of up to 4 GB in the system.
■
Do not remove any screws from the
memory upgrade module compartment
except the ones specifically shown in the
directions for installing and removing the
memory upgrade module.
■
The memory upgrade module can be
severely damaged by electrostatic dis-
charge (ESD). To minimize risk, observe
the following precautions:
Figure 2-6. Inserting a PC Card
■
Before handling a memory module,
Removing a PC Card
touch a grounded metal object to
discharge static electricity built up in
your body.
To remove a PC Card, first click the Safely Remove
Hardware icon in the system tray in the bottom right-
hand corner of the display. Select PC Card from the list,
and click [Stop].
■
When installing or removing a memory
module, hold it by the edge so as not
to touch any contacts or chips. Be
careful not to touch any computer
terminals or components; the oil from
your fingers could cause a short.
Press the PC Card eject button so that it pops out. Once
the button has popped out, press it firmly to eject the
card. (See Figure 2-7 for location)
■
Be sure to power down your system
before adding or removing memory
modules. Even if the system is in hiber-
nate or standby, data could be lost or
memory could be damaged if power is
still available to the system.
Installing a Memory Module
To install a DIMM module in the Tablet PC:
1. Ensure that the Tablet PC is off. To do so, carry out
the Shut Down command in the Start menu. (Do
not attempt to remove or install a DIMM module
when the system is in Standby mode or running.)
PC Card Eject Button
Figure 2-7. Removing a PC Card
2. Remove the two screws from the cover plate on the
back of the Tablet PC and remove the cover plate as
shown in Figure 2-8.
Figure 2-8. Accessing the Memory Slot
34
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
3. Insert the DIMM module in the socket at an angle
and push it down until it locks into place as shown in
Figure 2-9. Note that the DIMM module is keyed to
prevent it from being inserted backwards.
Removing a Memory Module
To remove a DIMM module:
1. Ensure that the Tablet PC is off. To do so, carry out
the Shut Down command in the Start menu. (Do not
attempt to remove or install a DIMM module when
the system is in Standby mode or running.)
2. Remove the screws from the cover plate on the back
of the Tablet PC and remove the cover plate as shown
in Figure 2-8.
3. Spread the fingers on the socket that lock the DIMM
module in place until the DIMM module is loose.
Figure 2-9. Installing a DIMM Module
4. Reinstall the cover and screws that you removed in
step 2.
5. Confirm that the DIMM module is recognized by the
system. To do so, run BIOS Setup. The size of the
DIMM module should be displayed in the Info menu
in BIOS Setup.
The DIMM module is installed in the Tablet PC and you
can now use the system.
Figure 2-10. Removing a DIMM Module
4. Remove the DIMM module from the socket.
The DIMM module is now removed from the Tablet PC.
See "Installing a Memory Module" to install a new DIMM
module.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T w o
36
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Care and
Maintenance
37
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T h r e e
38
Download from Www.Somanuals.com. All Manuals Search And Download.
C a r e a n d M a i n t e n a n c e
4. If your Tablet PC will not boot up after it has dried
out, call your support representative.
Care and Maintenance
This chapter gives you pointers on how to care for and
maintain your Stylistic ST5100 Series Tablet PC.
■
■
■
■
Do not use your Tablet PC in a wet environment (near
a bathtub, swimming pool).
Always use the AC adapter and batteries that are
approved for your system.
■
Do not remove any screws from the
memory upgrade module compartment
except the ones specifically shown in the
directions for installing and removing the
memory upgrade module.
Avoid exposure to sand, dust and other environmental
hazards.
Do not expose your Tablet PC to direct sunlight for
long periods of time as excessive temperatures may
damage your system.
■
The memory upgrade module can be
severely damaged by electrostatic dis-
charge (ESD). To minimize risk to the
module, observe the following precau-
tions:
■
■
Do not put heavy or sharp objects on the computer.
Do not carry your system in a bag or briefcase while it
is running; doing so could result in overheating or hard
disk drive problems.
■
Before docking or undocking your
system (when using a Tablet Dock), it
is good practice to always touch a
grounded metal object to discharge
static electricity built up in your body.
■
If you are carrying your system in a briefcase, or any
other carrying case, make sure that there are no objects
in the case pressing on the display.
■
Before handling a memory module,
touch a grounded metal object to
discharge static electricity built up in
your body.
■
Do not drop your Tablet PC or touch the screen with
any sharp objects.
■
When installing or removing a
memory module, hold it by the edge
so as not to touch any contacts or
chips. Be careful not to touch any
internal computer terminals or
components; the oil from your
fingers could cause a short to the
components.
PROTECTING THE DISPLAY SCREEN
The Stylistic ST5100 Series Tablet PC is designed to
provide you with years of service. Using a screen
protector will help ensure the screen remains as clear as
possible. When installed, the screen protector becomes a
durable, replaceable writing surface that protects the
display screen from abrasion.
■
Be sure to power down your system
before adding or removing memory
modules. Even if the system is in
hibernate or standby states, data
could be lost or the memory could be
damaged if power is still available to
the system.
To obtain additional screen protectors, use Fujitsu part
number FPCSP08AP (6-pack) when ordering. Additional
information about installation is included with the
screen protectors.
During normal use of the Tablet PC, small
particles from the environment can become
embedded in the pen tip and scratch the
screen. To prevent scratching the screen,
ensure that a screen protector is installed
before using your Tablet PC. The warranty
does not cover a scratched screen.
CARING FOR YOUR TABLET PC
Please note the following information regarding proper
treatment of your Tablet PC:
■
Your Tablet PC is a durable but sensitive electronic
device. Treat it with respect and care.
To install a new screen protector on your Tablet PC:
■
Make a habit of transporting the system in a suitable
carrying case.
1. If a screen protector is already installed on the display
screen, remove it before installing the new screen
protector.
■
Do not attempt to service the computer yourself.
Always follow installation and operation instructions
closely.
The screen protector is held onto the display screen
surface by a thin strip of adhesive around the edges. A
notch in one corner of the screen protector allows
you to slide your fingernail under the screen
protector for easy removal.
■
If you accidentally spill liquid on your Tablet PC:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T h r e e
2. Clean the display by wiping the screen gently using a
soft cotton cloth dampened with isopropyl alcohol.
Ensure that all residue has been removed from the
screen before applying a new screen protector.
Remove the protective coating from the adhesive
side of the screen protector first, as shown in Figure
3-1.
■
The Stylistic ST5100 Series Tablet PC is
not waterproof. Do not pour liquids on
the system or wash it with a heavily
soaked cloth.
■
Do not place items on the top of the dis-
play, or damage may occur.
Figure 3-3. Removing the protective cover
5. Remove the protective plastic cover from the face of
the screen protector, as shown in Figure 3-3.
.
6. Clean any residue left behind by the protective
coating from the exposed surface of the screen
protector by wiping gently with a soft cotton cloth
dampened with isopropyl alcohol. Wipe the screen
protector with a soft dry cloth to remove any low-
tack adhesive; this will help prevent the pen tip from
squeaking.
STORING THE TABLET PC
Store the Stylistic ST5100 Series Tablet PC in the Off
state with a fully charged battery installed. You can store
the Tablet PC in the Off state for about 30 days with a
fully charged battery installed. After this period, the
battery should be recharged or replaced with a charged
battery.
Figure 3-1. Removing the Protective Sheet
3. Apply the screen protector to the display screen
surface. When doing so, orient the screen protector
with the adhesive side of the screen protector facing
the display screen and the notched corner of the
screen protector oriented as shown in Figure 3-2.
If you intend to store the Tablet PC for a longer period of
time, the small battery that maintains system time may
need to be replaced. Replacement of the clock battery
should only be performed by authorized technicians.
AVOIDING OVERHEATING
Do not expose your Tablet PC to direct
sunlight for extended periods of time. High
temperatures could damage your tablet.
The Tablet PC monitors its internal temperature. As the
internal temperature approaches the tolerable limits of
heat-sensitive components, system functions are auto-
matically limited or turned off to prevent damage.
Figure 3-2. Installing the screen protector
4. Apply pressure to the screen protector with your
finger using a continuous wiping motion along the
edges. The adhesive sets completely within 48 hours.
To ensure a good seal between the screen protector
and the display, do not lift the screen protector from
the display once it has been applied.
To protect your tablet from damage and to optimize
performance, keep all air all vents unobstructed, clean,
and clear of debris. This may require periodic cleaning,
depending upon the system environment.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
C a r e a n d M a i n t e n a n c e
Do not operate the tablet in areas where the air vents can
be obstructed, such as in tight enclosures or on soft
surfaces like a bed or cushion.
Cursor Is Not Tracking Pen
If the cursor on the screen appears to be misaligned with
the pen or is not accurately tracking the pen, calibrate the
pen. See “Calibrating the Pen” on page 31 for more infor-
mation.
CLEANING THE DISPLAY SCREEN
To clean the Tablet PC display screen, wipe the screen
surface gently using a soft cotton cloth slightly dampened
with water or isopropyl alcohol.
Infrared Data Transfer Is Not Working
If you are experiencing problems transferring data over
the system’s infrared interface, note the following:
•
Can the IrDA port on the Tablet PC “see” the IrDA
port on the other device? A direct line-of-sight path
must exist between the IrDA port on the Tablet PC
and the IrDA port on the other device.
The Tablet PC is not waterproof. Do not
pour liquids on the Tablet PC or wash it
with a heavily soaked cloth.
•
•
The distance between the two devices must not be
more than 3 feet.
TROUBLESHOOTING
Solutions to some common problems are described in
the following sections. If you are experiencing a problem
with your Tablet PC that you cannot solve by taking the
actions described, contact your local help desk or reseller,
or call Fujitsu Service and Support at 1-800-8Fujitsu (1-
800-838-5487) for further assistance.
The viewing angle from the IrDA port on the Tablet
PC must not be more than 15 degrees from a center
line between the IrDA port on the Tablet PC and the
IrDA port on the other device.
•
•
The device with which you are trying to communicate
must be compliant with the IrDA Standard Revision
1.1 (or 1.0).
System Will Not Resume Operation
If the system will not resume operation after system oper-
ation has been suspended, check the following:
It may be necessary for both computers to be using
the same network connection protocols.
•
•
The battery may either be defective, or discharged to a
critically low level. When the battery reaches a
critically low level, the system is forced into Standby
mode to avoid a total system power failure. To correct
this problem, either connect an external power supply
(such as the AC adapter), or install a charged battery
in the Tablet PC.
Tablet PC is Not Responding to the Pen
If the Tablet PC does not respond to the pen, connect an
external keyboard to the system to see if it responds to
keyboard commands. If the system doesn’t respond to a
keyboard, the application or system may have crashed,
and it may be necessary to reboot the system. If the
system responds to a keyboard but not to a pen, contact
your local help desk or reseller, or call Fujitsu Service and
Support at 1-800-8Fujitsu (1-800-838-5487) for further
assistance.
The system may be at the critical thermal limit. To
avoid damage to heat-sensitive components, the
system enters standby mode when it gets too hot.
System operation cannot be resumed until the Tablet
PC cools off to a tolerable temperature. Move the
Tablet PC to a cooler location.
Speaker/Headphone Volume Too Low
If the audio volume on your Tablet PC speaker or
external headphones is too low, check the following:
Display Screen Blank or Difficult to Read
If the display screen on your Tablet PC appears blank or
is unreadable, confirm that the system is running (the
Power icon is displayed continuously on the Status
display), and check the following:
•
Ensure the speaker (or headphone output if using
headphones) is enabled. To do so, open the Control
Panel and double-click on the Sounds and Audio
Devices icon. Select the proper tab, and increase the
volume using the slider bar. (If you aren’t getting any
sound, uncheck the Mute box if it is checked.)
•
The system brightness may be set too low, causing the
screen to appear too dark. To change system
brightness, press the Fn button twice to open the
Fujitsu menu. Brightness can be adjusted from the
menu.
•
•
•
Press the Fn button twice to open the Fujitsu menu.
Volume can be adjusted from the menu.
Ensure the mute box in the system volume control
(accessible from the system tray) is not set.
•
The video timeout may have expired. Tap on the
display screen to reactivate the display. Note that this
is a normal, power-saving feature.
Ensure any volume control in your audio software is
set to an audible level.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T h r e e
Configuring Peripheral Interfaces
blue-coded components; you must select grey and
green components separately.
Certain peripheral devices can be disabled during the
BIOS Setup. If the peripheral interface you want to use
does not appear to be working with your peripheral
device, ensure that it is enabled in the BIOS. Contact
your local help desk or reseller, or call Fujitsu Service
and Support at 1-800-8Fujitsu (1-800-838-5487) if you
need assistance using BIOS Setup.
5. Once you have selected the components you wish to
install, click [Install Selected Subsystems]; the
components will be installed.
6. After the components are installed, click [OK], then
click [Yes] when asked if you want to reboot the
system.
RESTORING THE PRE-INSTALLED SOFTWARE
The Drivers and Applications Restore (DAR) DVD
contains sets of device drivers and Fujitsu utilities (in
specific directories) that are unique to your computer
configuration for use as documented below.
RESTORING THE FACTORY IMAGE
The Restore Disc only restores the primary
hard disk drive. If you have a second
partition on your hard drive, it will not be
restored using these utilities.
If you have access to the internet, visit the
Fujitsu Support website at: http://
check for the most current information,
drivers and hints on how to perform
recovery and system updates.
The Restore Disc that came with your system contains
two utilities:
■
The Recovery utility allows you to restore the original
contents of the C: drive.
■
The Hard Disk Data Delete utility on this disc is used
Re-Installing Individual Drivers and Applications
The Drivers and Applications CD can be used to
selectively re-install drivers and/or applications that may
to delete all data on your hard disk and prevent it from
being reused. Do not use the Hard Disk Data Delete
utility unless you are absolutely certain that you want
to erase your entire hard disk, including all partitions.
have been uninstalled or corrupted.
There may be certain free third-party
applications pre-installed on your system
that are not on the DAR CD. The latest
versions of the applications can be
• The use of this disc requires that you have
a device capable of reading DVDs
attached to your system. If you do not
have a built-in DVD player, you will need
to attach an external player. For more
information on available external devices,
visit our website at: us.fujitsu.com/
computers.
downloaded from the third-party’s website.
To re-install drivers and/or applications:
1. Boot up the system and insert the DAR CD after
Windows has started. A Fujitsu Installer screen is
displayed after the CD is inserted.
• This disc can only be used with the system
with which it was purchased.
2. After reading the License Agreement, click [I agree].
3. A window will appear containing a list of applica-
tions, drivers, and utilities that you can install from
the Drivers and Applications CD.
BOOT Priority Change
Before restoring an image, you must first verify that your
system is set up to boot from the DVD drive. To verify/
change the boot-up priority (rather than booting-up
from the hard drive or an external floppy disk drive),
perform the following steps:
The components listed are color-coded in
terms of their install status. Blue indicates
that the component can be installed. Green
indicates that the component needs to be
installed separately. Grey indicates a
component that is already installed; grey
items can be reinstalled, but prior to
installation you will receive a reminder that
the component is already installed.
Using TrustedCore Menu
To change the priority using the TrustedCore menu,
simply press the [ent] button when the Fujitsu logo
appears after powering on. Select Boot Menu, then select
“CD/DVD Drive”.
Using BIOS Setup Utility
1. Start your system and press the [Ctl-Alt-Del] button
when the Fujitsu logo appears. You will enter the
BIOS Setup Utility.
4. In the list, check off all the components you want to
install. If you want to install all components, click
[Select All]. Clicking [Select All] will select all of the
2. Using the arrow keys, go to the Boot menu.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
C a r e a n d M a i n t e n a n c e
3. Arrow down to the Boot Device Priority submenu.
Press [Enter].
AUTOMATICALLY DOWNLOADING
DRIVER UPDATES
Your system has a convenient tool called the Fujitsu
Driver Update (FDU) utility. With FDU, you can choose
to automatically or manually go to the Fujitsu site to
check for new updates for your system.
4. If “Optical Media Drive” or “CD-ROM Drive” is not
at the top of the list, arrow down to the drive in the
list, and press the space bar (or the + key) to move it
to the top of the list. (The system attempts to boot
from the devices in the order in which they are
listed.). Note that the BIOS for some systems will
indicate “CD-ROM Drive”, even when a DVD drive is
connected.
The FDU icon
should appear in the system tray at
the bottom right of your screen (roll the cursor over the
icons to find the correct one). If the FDU icon does not
appear in the system tray, it can be started by going to
[Start] -> All Programs, and clicking on Fujitsu Driver
Update; this will create the icon automatically.
5. If you have an external DVD drive connected,
proceed to the next step; otherwise, proceed to
step 7.
To invoke the FDU menu, right-click on the FDU icon.
The menu contains the following items:
6. If you have an external DVD drive connected:
• Select the Advanced menu in the BIOS window.
■
Check for updates now
• Scroll down to the USB Features submenu and
press the Enter key to open it.
Allows for manual driver update search. The first time
it is used, you are prompted to agree to a user agree-
ment. After clicking on the icon, the FDU automati-
cally connects with the Fujitsu site to check for updates
and downloads them. While downloading, the icon
has a red bar through it, indicating that it cannot be
used while the download is in process. When the
update is complete, a message appears informing you
of the fact.
• If Legacy USB Support is disabled, press the space
bar to enable it.
• Scroll down to SCSI SubClass Support and press
the space bar to enable it.
7. Press [F10], then click on [Yes] to exit the BIOS Setup
Utility and return to the boot process.
■
Enable Automatic Update Notifications
After you have changed the boot priority, you can restore
a backup image when you are booting up.
Automatically searches for new updates on a regular
basis (approximately every 3 days).
■
Procedure
Show update history
Brings up a screen that displays a history of updates
that have been made via the FDU.
1. Turn on the power to your system.
2. Ensure that you have a device that can read DVDs
either installed in your system or attached externally
to it.
■
About Fujitsu Driver Update
Displays the FDU version number and copyright
information
3. Insert the Restore Disc into the drive tray.
4. Reboot your system.
■
Fujitsu Driver Update Readme
Displays the FDU readme.
5. After the system reboots, follow the instructions that
appear to either restore your system image or erase
all data from your hard disk.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n T h r e e
44
Download from Www.Somanuals.com. All Manuals Search And Download.
4
System
Specifications
45
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n F o u r
46
Download from Www.Somanuals.com. All Manuals Search And Download.
S y s t e m S p e c i f i c a t i o n s
Stylistic ST5100 Series Hardware Specifications
The following table provides general hardware specifica-
tions of the Stylistic ST5100 Series Tablet PC by category.
Stylistic ST5100 Specifications (Continued)
10.4" Display
• Reflective Color LCD
• Indoor/Outdoor Viewability
• Active Digitizer
Stylistic ST5100 Specifications
Processing Specifications
• Outdoor-viewable
• 16-bit color
CPU
Intel® Core™2 Duo Processor
ULV U7600*
• 10.4” TFT XGA (1024 x 768),
16M colors
Chip set
Intel 945GM - 533 MHz FSB
1.2 GHz*
• Brightness: 8 levels
Processor
Speed
VRAM
Up to 224 MB of shared memory using
Unified Memory Architecture (UMA).
Dynamically responds to application
requirements and allocates the proper
amount of memory for optimal graphics
and performance.
Memory/Storage Specifications
Main RAM
• 2 DIMM slots available
• 200-pin SO DIMM modules
• DDR2 533 MHz
Physical Specifications
• 256 MB, 512 MB, 1 GB, and 2 GB
module configurations available,
with a system maximum of 4 GB.
Dimensions
12.1" Display (Active Digitizer):
12.77" x 8.66" x 0.82"-0.94"
(324.4 mm x 220 mm x 20.9-23.8 mm)
10.4" Display (Reflective Digitizer):
12.77" x 8.66" x 0.91"-1.01"
L1 cache
(CPU)
32 KB on-die
L2 cache
2 MB on-die
1 MB .
(324.4 mm x 220 mm x 23.2-25.7 mm)
BIOS ROM
Weight
3.5 lbs. (1.59 Kg) (with battery)
Hard disk
drive
• 2.5” HDD
Interface Specifications
• 40 GB, 60 GB, 80 GB, 100 GB, or
120 GB HDD*
Card Slots
• PCMCIA: One Type I or Type II,
PCMCIA CardBus version 3.0
• SATA
• Secure Digital (SD)/
Memory Stick slot
• Serial ATA 150
• 5400 rpm
• Smart Card slot
• Shock-mounted
• Shock Sensor Technology
Integrated
Interfaces
• Modem (RJ-11)
• LAN (RJ-45)
• IEEE 1394 (S400 4-pin)
• USB 2.0 (Qty. 2)
• DC-In
Display Specifications
Depending on the configuration of your system, it has
either a 12.1" transmissive or a 10.4" reflective display
12.1" Display
• Transmissive Color LCD
• Indoor/Outdoor Viewability
• Active Digitizer
• IrDA
• 15-pin D-SUB connector for
external VGA monitor
• Docking connector
• 16-bit color
• 12.1” TFT XGA (1024 x 768),
16M colors
Infrared
IrDA version 1.1 (FIR, 4Mbps)
Keyboard/Mouse IR Port (Qty. 2)
Keyboard/
Mouse
support
• Brightness: 8 levels
• Viewing Angle:
Horizontal: 80 degrees (max.)
Vertical: 80 degrees (max.)
• Contrast Ratio: Typ. 250, Min. 100
* The specifications for your particular model may vary.
To determine the specifications for your system, please
visit our website at: us.fujitsu.com/computers.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n F o u r
Stylistic ST5100 Specifications (Continued)
Stylistic ST5100 Specifications (Continued)
Wireless LAN
Your system may have one of the two
following Wireless LAN devices
installed:
Agency Approval Specifications
• EN55022 (CISPR22) Class B
• FCC 15/15E, Class B
• VCCI Class B
Emissions
• Integrated Intel PRO/Wireless
3945ABG Network Connections
(802.11a+b/g)
Immunity
Safety
• EN55024 (1998)
• Integrated Atheros Super AG
Wireless LAN (802.11a/b/g)
• UL and cUL Listed, UL 60950-1,
1st edition
• CB Report, IEC 60950-1, 1st edition
Audio
• Sigmatel STAC9753A codec
• Internal mono microphone and
speaker
Specific
Absorption
Rate (SAR)
• FCC/RSS
• ACA/EN
• Dual digital microphones (12.1"
model only)
Wireless
• EN300328
• EN301489
• EN301893
• FCC 15E
• RSS210
• Stereo headphone jacks
User Controls
• Application Buttons, each with
primary, secondary, tertiary, and
security functions
• Fingerprint swipe sensor for
biometric security (12.1" model
only)
• RSS220
• FCC Part 68
• IC CS-03
• Power On/Suspend/Resume button
Telecom
Other
• Emergency Shutoff Button (Power
Off button)
• Energy Star
• Two Navigation buttons
Additional Specifications
Status
Indicators
(LEDs)
• Power
Security
Features
• Security Panel
• Charge/DC-In
• Battery level
• HDD
• Fingerprint Swipe Sensor (12.1"
model only)
• Trusted Platform Module (TPM)
• Security
• Microsoft® Windows® XP
Tablet PC Edition 2005, or,
Operating
Systems
Power Specifications
• Microsoft Windows Vista™
Business Edition
Main Battery
Bridge Battery
• 6-cell (standard), 10.8V, 5200 mAh,
56 Wh
• 9-cell (optional), 10.8V, 7800 mAh,
84 Wh
• Removable, Lithium ion
• Warm-swappable
• 6-cell NiMH, 35 mAh
• Life (with Standby on bridge
battery only):
5 minutes from full charge
AC Adapter
Temperature
• Autosensing 100 - 240V, supplying
16 VDC, with a current of 3.75 A
Environmental Specifications
Operating: 41o - 95o F (5o - 35o C)
Non-operational: 14o - 140o F
(-10o - 60o C)
Humidity
Operating: 20 - 85% non-condensing
Non-operating: 8 - 85% non-
condensing
48
Download from Www.Somanuals.com. All Manuals Search And Download.
S y s t e m S p e c i f i c a t i o n s
Regulatory Information
The ringer equivalent number (REN) of this equipment
is 0.1B as shown on the label. The REN is used to deter-
mine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone may result
in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should
not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by
the total RENs, contact the local telephone company.
NOTICE
Changes or modifications not expressly approved by
Fujitsu could void this user’s authority to operate the
equipment.
FCC NOTICES
Notice to Users of Radios and Television
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules.
If this equipment causes harm to the telephone network,
the telephone company will notify you in advance that
temporary discontinuance of service may be required.
But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
The telephone company may make changes in its facili-
ties, equipment, operations or procedures that could
effect the operation of the equipment. If this happens the
telephone company will provide advance notice in order
for you to make necessary modifications to maintain
uninterrupted service.
■
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
■
If trouble is experienced with this equipment, for repair
or warranty information, please refer to the manual or
contact Fujitsu Computer Systems Corporation,
Customer Service. If the equipment is causing harm to
the telephone network, the telephone company may
request that you disconnect the equipment until the
problem is resolved.
receiver.
■
Connect the equipment into an outlet that is on a
different circuit than the receiver.
Consult the dealer or an experienced radio/TV
■
technician for help.
Shielded interconnect cables must be employed with this
equipment to ensure compliance with the pertinent RF
emission limits governing this device.
The equipment cannot be used on public coin service
provided by the telephone company. Connection to party
line service is subject to state tariffs. (Contact the state
public utility commission, public service commission or
corporation commission for information).
Notice to Users of the US Telephone Network
This equipment complies with Part 68 of the FCC rules,
and the requirements adopted by ACTA. On the bottom
of this equipment is a label that contains, among other
information, the FCC registration number and ringer
equivalence number (REN) for this equipment; or a
product identifier in the format US:AAAEQ##TXXXX. If
requested, this information or number must be provided
to the telephone company.
If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation of
this computer does not disable your alarm equipment. If
you have any questions about what will disable alarm
equipment, consult your telephone company or a quali-
fied installer.
This equipment is designed to be connected to the tele-
phone network or premises wiring using a standard jack
type USOC RJ11C. A plug and jack used to connect this
equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant tele-
phone cord and modular plug is provided with this
product. It is designed to be connected to a compatible
modular jack that is also compliant.
The Telephone Consumer Protection Act of 1991 makes
it unlawful for any person to use a computer or other
electronic device to send any message via a telephone fax
machine unless such message clearly contains in a margin
at the top or bottom of each transmitted page or on the
first page of the transmission, the date an time it is sent
and an identification of the business or other entity, or
other individual sending the message and the telephone
number of the sending machine or such business, other
entity, or individual.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
S e c t i o n F o u r
DOC (INDUSTRY CANADA) NOTICES
Avis Aux Utilisateurs Du Réseau
Notice to Users of Radios and Television
Téléphonique Canadien
This Class B digital apparatus meets all requirements of
Canadian Interference-Causing Equipment Regulations.
AVIS: Le présent matériel est conforme aux spécifica-
tions techniques d’Industrie Canada applicables au
matériel terminal. Cette conformité est confirmée par le
numéro d’enregistrement. Le sigle IC, placé devant le
numéro d’enregistrement, signifie que l’enregistrement
s’est effectué conformément à une déclaration de
conformité et indique que les spécifications techniques
d’Industrie Canada ont été respectées. Il n’implique pas
qu’Industrie Canada a approuvé le matériel.
CET appareil numérique de la class B respecte toutes les
exigence du Réglement sur le matérial brouilleur du
Canada.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry
Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The
abbreviation, IC, before the registration number signi-
fies that registration was performed based on a Declara-
tion of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that
Industry Canada approved the equipment.
Avant de connecter cet équipement à une ligne télépho-
nique, l’utilisateur doit vérifier s’il est permis de
connecter cet équipement aux installations de télécom-
munications locales. L’utilisateur est averti que même la
conformité aux normes de certification ne peut dans
certains cas empêcher la dégradation du service.
Before connecting this equipment to a telephone line the
user should ensure that it is permissible to connect this
equipment to the local telecommunication facilities.
The user should be aware that compliance with the
certification standards does not prevent service
degradation in some situations.
Les réparations de l’équipement de télécommunications
doivent être effectuées par un service de maintenance
agréé au Canada. Toute réparation ou modification, qui
n’est pas expressément approuvée par Fujitsu, ou toute
défaillance de l’équipement peut entraîner la compagnie
de télécommunications à exiger que l’utilisateur décon-
necte l’équipement de la ligne téléphonique.
Repairs to telecommunication equipment should be
made by a Canadian authorized maintenance facility.
Any repairs or alterations not expressly approved by
Fujitsu or any equipment failures may give the telecom-
munication company cause to request the user to
disconnect the equipment from the telephone line.
AVIS: L’indice d’équivalence de la sonnerie (IES) du
présent matériel est de 0.1B. L’IES assigné à chaque
dispositif terminal indique le nombre maximal de
terminaux qui peuvent être raccordés à une interface
téléphonique. La terminaison d’une interface peut
consister en une combinaison quelconque de dispositifs,
à la seule condition que la somme d’indices d’équiva-
lence de la sonnerie de tous les dispositifs n’excède pas 5.
NOTICE: The Ringer Equivalence Number (REN) for
this terminal equipment is 0.1B. The REN assigned to
each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected
to a telephone interface. The termination on an interface
may consist of any combination of devices subject only
to the requirement that the sum of the Ringer Equiva-
Pour assurer la sécurité, les utilisateurs
doivent vérifier que la prise de terre du ser-
vice d’électricité, les lignes télphoniques et
les conduites d’eau métalliques sont con-
nectées ensemble. Les utilisateurs NE
doivent PAS tenter d’établir ces connex-
ions eux-mêmes, mais doivent contacter
les services d’inspection d’installations
électriques appropriés ou un électricien.
Ceci peut être particulièrement important
en régions rurales.
lence Numbers of all the devices does not exceed five.
For safety, users should ensure that the
electrical ground of the power utility, the
telephone lines and the metallic water
pipes are connected together. Users should
NOT attempt to make such connections
themselves but should contact the appro-
priate electric inspection authority or elec-
trician. This may be particularly important
in rural areas.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
WirelessLAN/Bluetooth*
User’s Guide
* Optional devices
51
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
52
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from
the one the receiver is connected to.
4. Consult the dealer or an experienced radio/TV technician for
help.
FCC REGULATORY INFORMATION
Please note the following regulatory information related to the
optional wireless LAN module.
Regulatory Notes and Statements
Wireless LAN, Health and Authorization for use
FCC Radio Frequency Exposure statement
The available scientific evidence does not show that any health
problems are associated with using low power wireless devices.
There is no proof, however, that these low power wireless devices
are absolutely safe. Low power wireless devices emit low levels of
radio frequency energy (RF) in the microwave range while being
used. Whereas high levels of RF can produce health effects (by
heating tissue), exposure to low-level RF that does not produce
heating effects causes no known adverse health effects. Many
studies of low-level RF exposure have not found any biological
effects. Some studies have suggested that some biological effects
might occur, but such findings have not been confirmed by addi-
tional research. The wireless LAN radio device has been tested and
found to comply with FCC radiation exposure limits set forth for an
uncontrolled equipment and meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65.
Radio frequency electromagnetic energy is emitted from Wireless
LAN devices. The energy levels of these emissions, however, are far
much less than the electromagnetic energy emissions from wireless
devices such as mobile phones. Wireless LAN devices are safe for
use by consumers because they operate within the guidelines found
in radio frequency safety standards and recommendations. The use
of Wireless LAN devices may be restricted in some situations or
environments, such as:
■
On board an airplane, or
■
In an explosive environment, or
■
In situations where the interference risk to other devices or ser-
vices is perceived or identified as harmful.
In cases in which the policy regarding use of Wireless LAN devices
in specific environments is not clear (e.g., airports, hospitals, chem-
ical/oil/gas industrial plants, private buildings), obtain authoriza-
tion to use these devices prior to operating the equipment.
The maximum SAR values measured from the devices are:
■
Intel PROSet Wireless LAN (WM3945ABG): 1.47 W/kg
Atheros Wireless LAN (AR5BX6): 1.57 W/kg
Intel PROSet Wireless LAN (WM3945ABG) + Bluetooth
■
Regulatory Information/Disclaimers
■
Installation and use of this Wireless LAN device must be in strict
accordance with the instructions included in the user documenta-
tion provided with the product. Any changes or modifications
made to this device that are not expressly approved by the manufac-
turer may void the user’s authority to operate the equipment. The
manufacturer is not responsible for any radio or television interfer-
ence caused by unauthorized modification of this device, or the
substitution or attachment of connecting cables and equipment
other than those specified by the manufacturer. It is the responsi-
bility of the user to correct any interference caused by such unau-
thorized modification, substitution or attachment. The
Simultaneous: 1.47 W/kg
Atheros Wireless LAN (AR5BX6) + Bluetooth Simultaneous:
1.56 W/kg
■
Export restrictions
This product or software contains encryption code which may not
be exported or transferred from the US or Canada without an
approved US Department of Commerce export license. This device
complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB
003 B. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesirable operation. Modifications not expressly autho-
rized by Fujitsu Computer Systems Corporation may invalidate the
user's right to operate this equipment.
manufacturer and its authorized resellers or distributors will
assume no liability for any damage or violation of government
regulations arising from failure to comply with these guidelines.
This device must not be co-located or operating in conjunction
with any other antenna or transmitter.
Canadian Notice
The device for the 5150-5250 MHz band is only for indoor usage to
reduce the potential for harmful interference to co-channel mobile
satellite systems.
Federal Communications Commission statement
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause interference, and, (2) This device must accept
any interference, including interference that may cause undesired
operation of this device.
The maximum antenna gain of 6 dBi permitted (for devices in the
5250-5350 MHz, 5470-5725, and 5475-5825 MHz bands) to comply
with the e.i.r.p. limit as stated in A9.2 of RSS210.
In addition, users should also be cautioned to take note that high
power radars are allocated as primary users (meaning they have
priority) of 5250-5350 MHz and 5650-5850 MHz and these radars
could cause interference and/or damage to LE-LAN devices.
FCC Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy.
If not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try and correct the interference
by one or more of the following measures:
53
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
Before Using the Wireless LAN
This manual describes the procedures required to prop-
erly setup and configure the optional integrated Wireless
LAN Mini-PCI device (referred to as "WLAN device" in
the rest of the manual). Before using the WLAN device,
read this manual carefully to ensure it's correct opera-
tion. Keep this manual in a safe place for future refer-
ence.
Keying (CCK) when the WLAN device is operating in
IEEE 802.11b mode and Orthogonal Frequency Divi-
sion Multiplexing (OFDM) when operating in
IEEE802.11a or IEEE802.11g mode.
■
The WLAN device is Wi-Fi certified and operates at
the maximum data transfer rate of 54 Mbps in
IEEE802.11a or IEEE802.11g mode and 11 Mbps in
IEEE802.11b mode.
Wireless LAN Devices Covered by this Document
This document is applicable to systems containing one
of the following two devices. Most of the procedures are
identical. Sections that differ between the two devices
have been noted in the text:
■
The WLAN device supports the following encryption
methods - WEP, TKIP, and AES encryption.
Wireless LAN Modes Using this Wireless Module
Ad Hoc Mode (See Figure A-1)
■
Intel® PRO/Wireless 3945ABG (WM3945ABG)
Network Connection (802.11a+b/g)
“Ad Hoc Mode” refers to a type of wireless network that
involves connecting multiple computers without the use
of an Access Point. Network connectivity between
computers can be established using only wireless LAN
cards in a peer-to-peer fashion.
■
Atheros® AR5006EXS (AR5BXB6) Mini-Card
Wireless network card (802.11a+b/g)
Characteristics of the WLAN Device
The WLAN device is a Mini-PCI card attached to the
■
Ad Hoc networks are an easy and inexpensive method
for establishing network connectivity between multiple
computers.
main board of the mobile computer.
■
It operates in two license-free RF bands, therefore
eliminating the need to procure an FCC license to
operate. It operates in the 2.4GHz Industrial, Scien-
tific, and Medical (ISM) RF band and in the lower and
middle bands of the 5GHz Unlicensed National Infor-
mation Infrastructure (UNII) bands.
In Ad Hoc mode, you can use Microsoft Network func-
tions, such as File and Print Sharing to share folders,
printers, or other peripheral devices, and exchange files
with other computers.
■
The WLANs are capable of three operating modes,
To use Ad Hoc Mode, you must set the same SSID and
the same encryption key for all the computers that are
connected. Communication between computers in an
Ad Hoc network will occur provided they are within
each other’s RF coverage area.
IEEE802.11a, IEEE802.11b and IEEE802.11g, wireless
LAN standards governed by the IEEE (Institute of
Electronics and Electrical Engineers).
■
Encoding of data is modulated using Direct Sequence
Spread Spectrum (DSSS) and Complementary Code
Figure A-1. Ad Hoc Mode Network
54
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Access Point (Infrastructure) Mode (See Figure A-2)
ceptible to the energy and unable to communicate
properly.
Infrastructure mode refers to a wireless network in which
devices communicate with each other by first going
through an Access Point (AP). In infrastructure mode,
wireless devices can communicate with each other or can
communicate with a wired network. Most corporate
wireless LANs operate in infrastructure mode because
they require access to the wired LAN in order to use
services such as file servers or printers.
■
Broadcast stations or wireless communication equip-
ment that operate in the 2.4GHz or 5GHz RF Fre-
quency band may interfere with the operation of the
wireless LAN module. Increasing of transmit power or
relocating Access Points may be necessary to combat
the effects of the interference.
STOPPING TRANSMISSION
How to Handle This Wireless Module
To use this product inside hospitals, clinics, or airplanes,
or in other places where the use of electronic equipment
is regulated, stop the transmission of radio waves from
the wireless LAN beforehand.
The Integrated Wireless LAN device is already installed in
your mobile computer. Under normal circumstances, it
should not be necessary for you to remove or re-install it.
The wireless LAN has been configured to support the
operating system with which your system shipped.For
better communications
Deactivation using the wireless switch
The transmission of radio waves from the wireless LAN
can be stopped by setting the wireless switch to the Off
position. Note that the wireless LAN On/Off switch has
no effect on non-wireless LAN models.
This personal computer may not operate properly due to
the operating environment. It is highly recommended
that you observe the following precautions when using
your wireless LAN module:
(See Figure A-3 for Wireless LAN switch location.)
■
For optimum wireless communications, it recom-
Deactivation using Windows
mended that operation of the wireless LAN module
occur within 25 meters of the Access Point. Wireless
range is dependent on a multitude of factors including
number of obstructions, walls, type of construction
material, reflective objects, etc.
Intel PROSet Wireless LAN:
1. Click [Start] --> [(All) Programs] --> [Intel Net-
work Adapters] --> [Intel(R) PROSet]. The Intel(R)
PROSet window will be displayed.
■
If the computer is unable to communicate properly,
2. Click the General tab.
change the channel to be used or the installation loca-
tion. During the use of a microwave oven or other
equipment generating strong high-frequency energy, in
particular, the personal computer may be highly sus-
Select [Off] for the wireless communications Switch
Radio: function, and then click the [OK] button. Wireless
communications on/off switching will be deactivated and
the transmission of radio waves from the wireless LAN
will be stopped
Figure A-1. Access Point (Infrastructure) Network
Wired LAN
ADSL modem,
cable modem,
Internet
or similar
Access Point*
Wireless LAN
* An optional hub for a wired
LAN may be required depending
Upon the type of access point used.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
To restart transmission, check the [Enable
Radio] checkbox to select it., then click the
[OK] button.
STARTING TRANSMISSION
Wireless LAN
On/Off
Switch
To communicate using the wireless LAN function, set
the computer to a status from which it can transmit, as
follows:
Intel PROSet Wireless LAN:
1. Set the wireless switch to the On position.
2. Click [Start] --> [(All) Programs] --> [Intel Net-
work Adapters] --> [Intel(R) PROSet]. The
Intel(R) PROSet window will be displayed.
3. Click the [General] tab if it is not already selected.
4. Select [ON] for the Switch radio: function, then
click [OK]. Wireless communications on/off
switching will be activated and the transmission of
radio waves will be restarted.
Figure A-3. Wireless LAN On/Off Switch
To restart transmission, select [On] for the
wireless communications Switch Radio:
function, and then click the [OK] button.
Atheros Wireless LAN:
1. Click the Wireless Network Connection icon in the
system tray at the lower right of your screen.
Atheros Wireless LAN
1. Click [Start] --> [All Programs] --> [Atheros] -->
[Atheros Client Utility].
2. Click [Enable Radio]. The radio will be turned on.
Access Point Mode: Transmission is enabled.
Ad Hoc Mode: Restart your computer to enable the
radio.
2. Click [Action].
3. Click [Disable Radio]. Wireless communications
on/off switching will be deactivated and the trans-
mission of radio waves from the wireless LAN will
be stopped.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Connecting the WLAN
The optional WLAN Device can be configured to estab-
lish wireless network connectivity using one of the
following tools:
Connecting to a Network with Windows Vista
After you have configured your computer, you can
connect to an active network by performing the
following steps:
■
Intel PROSet Software - The Intel PROSet Software
allows for multiple profile setup and supports auto-
matic profile switching. Support for most industry
standard security solutions is contained in this soft-
ware.
1. Click on the WLAN icon in the system tray.
2. Select “Connect to a network”.
Select a network from the list that appears, and click the
[Connect] button.
■
Atheros Client Utility - The Atheros Client Utility soft-
ware allows for multiple profile setups and supports
automatic profile switching. Support for most indus-
try standard security solutions is contained in this
software.
CONFIGURING THE WLAN USING
WINDOWS XP
Configuring Using Intel PROSet Software
There are two procedures outlines below. The first one is
for use with the Windows Vista operating system, and
the other is used with the Windows XP operating
system.
This section explains the procedure to properly
configure the WLAN device in a system using Windows
XP using the Intel PROSet Software. Pre-defined param-
eters will be required for this procedure. Please consult
with your network administrator for these parameters:
CONFIGURING THE WLAN
WITH WINDOWS VISTA
Network Name - Also known as the SSID
The WLAN device can be configured to establish wire-
less network connectivity using the software that is built
into Windows Vista. Support for most industry standard
security solutions is contained in this software.
Network Key (WEP) - Required if using static WEP
keys.
Authentication Type - Open, Shared, WPA, or WPA-
PSK
Pre-defined parameters will be required for this proce-
dure. Please consult with your network administrator
for these parameters:
Procedure
1. Activate the WLAN device using either the Wireless
On/Off Switch or the Intel PROSet software.
1. Click the Start button, then select Control Panel.
2. If the Control Panel is not in Classic View, select
Classic View from the left panel. Double-click the
Network and Sharing Center icon.
2. Click the [Start] button first and then [All Pro-
grams].
3. Click the icon [Intel PROSet Wireless] to execute
the Intel PROSet Wireless software.
3. Select “Manage wireless networks” from the left
panel.
4. Click the [Add] button. The General Settings dialog
displays.
4. Click on the [Add] button.
5. Depending upon what type of connection you
would like to make, make a selection. For an infra-
structure network, select “Manually create a net-
work profile. For ad hoc network, select “Create an
ad hoc network”.
5. Enter a profile name in the Profile Name field.
6. Enter the network SSID, in the Network Name
(SSID) field.
7. Click Infrastructure or Ad Hoc for the operating
mode.
6. Enter the required information. It may be necessary
to consult with your network administrator for
some of the information.
8. Click [Advanced].
9. The Mandatory Access Point option is only used if
Infrastructure mode is selected. Use this option to
connect to a specific access point. Enter the MAC
address for the access point. Click OK to save the
setting and return to the General Settings page.
7. In the event you require assistance, go to the Net-
work and Sharing Center window (Start -> Control
Panel -> Network and Sharing Center), and type in
relevant keywords in the Search box.
10. Click [Next].
57
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
11. If you are using Cisco CCX, click Cisco Options to
enable Cisco CKIP data encryption on the Security
Settings page. Check the Cisco Compatible Exten-
sions Options. If you have checked the Cisco's
"Mixed-Cell" box in the Advanced Setting, this
option must also be checked.
procedure. Please consult with your network adminis-
trator for these parameters:
Network Name - Also known as the SSID
Network Key (WEP) - Required if using static WEP
keys.
12. Click [OK].
13. Click Next.
Authentication Type - Open, Shared, WPA, or WPA-
PSK
Procedure
14. Select Open, Shared, WPA-Enterprise, WPA2-
Enterprise, WPA-Personal, or WPA2-Personal in
the Network Authentication options.
1. Activate the WLAN device using either the Wireless
On/Off Switch or the Atheros Client Utility
15. Select either None, WEP, CKIP (if Enable Cisco Cli-
ent eXtentions is enabled, use CKIP or WEP), or
TKIP for the data encryption.
2. Right-click on the “Atheros Client Utility” icon in
the system tray, and select “Open Atheros Client
Utility” from the menu.
16. If WEP is selected, select either 64 or 128-bit for the
Encryption Level.
3. From the Current Status page, click the Profile
Management tab.
17. Select the key index 1, 2, 3 or 4.
4. If this is your first time using this utility, highlight
the profile [Default] and Click the [Modify] button,
otherwise Click the [New] button. The General Set-
tings dialog displays.
18. Enter the WEP key if required. If your network does
not employ a 802.1x/EAP security mechanism,
please skip to step 24.
5. From the General page, enter a profile name in the
Profile Name field.
19. Click the Enable 802.1x checkbox to enable the
802.1x security option. Please contact your network
administrator if configuration of this setting is
required.
6. Enter the network SSID, in the SSID1 field. If you
wish to create a profile that can connect to up to 3
different wireless networks, SSID's can be entered
in the SSID2 and SSID3 fields as well.
20. Select the appropriate Authentication Type. Please
contact your network administrator if configura-
tion of this setting is required.
7. Click the Security tab.
21. After selecting your authentication type, enter the
user name, domain, and password of the user you
have created on the authentication server. The user
name and password do not have to be the same as
name and password of your current Windows user
login.
8. The Security tab allows for the configuration of the
Security modes listed in the table below. Please
select the radio button of the desired security
mode. If these settings are not known to you,
please consult with your network administrator for
the correct settings.
22. Click [OK] to save the settings.
Field Name
Description
23. From the Intel ProSet Wireless page, click the new
profile name shown in the Profile List. Use the up
and down arrows to position the priority of the
new profile in the priority list.
WPA
Enables the use of Wi-Fi Protected
Access. Choosing WPA opens the
WPA EAP drop-down menu.
Options include TLS and PEAP. If
these settings are not known to you,
please consult with your network
administrator for the correct settings.
24. Click the Connect button to connect to the net-
work.
WPA-PSK
Enables WPA-Pre-Shared Key. Click
on the Configure button to enter the
WPA Passphrase. If these settings
are not known to you, please consult
with your network administrator for
the correct settings.
25. Click [Close] if you want to close the Intel PROSet
for Wireless window.
Configuring Using Atheros Client Utility Software
This section explains the procedure to properly
configure the WLAN device using the Atheros Client
Utility. Pre-defined parameters will be required for this
58
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
CONNECTION TO THE NETWORK
This section explains connection to the network.
If there is an administrator of the network, contact the
network administrator for data settings.
802.1x
Enables 802.1x security. If these
settings are not known to you,
please consult with your network
administrator for the correct settings.
Choosing this option opens the
802.1x EAP type drop-down menu.
Options include TLS, PEAP, and LEAP
Setting the network
Perform the “Setting TCP/IP” and “Confirming the
computer and work group names” operations required for
network connection.
Pre-Shared Key
Enables the use of pre-shared keys
that are defined on both the access
point and the station. This is where
static WEP keys are entered. Click
the Configure button to fill in the
Define Pre-Shared Keys window.
Setting TCP/IP
To change the setting of the IP address,
you need to be logged in from Windows
as an administrator.
None
No security
9. Click OK
1. Click the [Start] button first and then [Control
Panel].
10. Click the Advanced tab
11. The Advanced tab allows for the configuration of
the options detailed in the table below.
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
Field Name
Description
Power Save
Mode
Options are Maximum, Normal, or
Off
3. Double-click [Network Connections]. A list of cur-
rently installed networks will be displayed.
Network Type
Options are AP (Infrastructure) or Ad
Hoc
4. Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu dis-
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
802.11b
Preamble
Specifies the preamble setting in
802.11b. The default setting is Short
and Long (Access Point mode),
which allows both short and long
headers in the 802.11b frames. Set
to Long Only to override allowing
short frames.
5. Click the [General] tab if it is not already selected.
6. Click [Internet Protocol (TCP/IP] and then click
[Properties]. The [Internet Protocol (TCP/IP)
Properties] window will be displayed.
TransmitPower
Level
Options are 100%, 50%, 25%,
12.5% or Lowest transmit power
(0mW)
7. Set the IP address as follows:
Wireless Mode
Specifies the wireless mode in an
access point network.
■
For ad hoc connection: Select [Use the following
IP address:] and then enter data for [IP address]
and [Subnet mask]. See page 67 for IP address
setting.
Wireless Mode
when Starting
Ad Hoc
Specifies 5GHz 54 Mbps, 5 GHz 108
Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz
54 Mbps to start an Ad Hoc network
if no matching network name is
found after scanning all available
modes.
Network
■
For access point (infrastructure) connection: If
your network uses DHCP, select [Obtain an IP
address automatically] and [Obtain DNS server
address automatically]. If your network uses static
IP addresses, consult with your network adminis-
trator for the correct IP address settings.
12. Click OK
13. If the profile you just created does not activate
immediately, click the Profile Management tab,
highlight the desired Profile, and click Activate.
8. Click the [OK] button. Processing will return to the
[Wireless Network Connection Properties] window.
14. Click OK to close the Atheros Client Utility.
9. Click the [OK] button.
10. Close the [Network Connection] window.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
Following this operation, confirm the names of the
computer and the workgroup as follows.
This operation is not required unless the sharing func-
tion is to be used.
The folder and printer for which the sharing function
has been set will be usable from any personal computer
present on the network.
Confirming the computer and work group names
To modify the computer name and/or the
work group name, you need to be logged
in from Windows as an administrator.
To share a file and/or the connected
printer, you need to be logged in as an
administrator.
1. Click the [Start] button, then [Control Panel].
Setting the Microsoft network-sharing service
1. Click the [Start] button first and then [Control
Panel].
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
3. Double-click the [System] icon. The [System Prop-
erties] window will be displayed.
4. Click the [Computer Name] tab.
3. Double-click [Network Connections]. A list of cur-
rently installed networks will be displayed.
5. Confirm the settings of [Full computer name:] and
[Workgroup:].
4. Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu dis-
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
a. The setting of [Full computer name:] denotes the
name for identifying the computer. Any name
can be assigned for each personal computer.
5. If [File and Printer Sharing for Microsoft Net-
works] is displayed, proceed to step 6. If [File and
Printer Sharing for Microsoft Networks] is not dis-
played, skip to step 7.
To change the name, click [Change] and
then proceed in accordance with the
instruction messages displayed on the
screen.
6. Make sure that the [File and Printer Sharing for
Microsoft Networks] check box is checked, and
then click the [OK] button. Skip to “Setting file-
sharing function”.
Enter the desired name in less than 15 ASCII
character code format. Identifiability can be
enhanced by entering the model number, the
user name, and other factors.
7. Click [Install]. The [Select Network Component
Type] window will be displayed.
b. [Workgroup name] is the group name of the
network. Enter the desired name in less than 15
ASCII character code format.
8. Click [Service], then click the [Add] button. The
[Select Network Service] window will be displayed.
For ad hoc connection: Assign the same network
name to all personal computers existing on the
network.
9. Click [File and Printer Sharing for Microsoft Net-
works] and then click the [OK] button. Processing
will return to the [Wireless Network Connection
Properties] window, and [File and Printer Sharing
for Microsoft Networks] will be added to the list.
For access point (infrastructure) connection:
Assign the name of the work group to be
accessed.
10. Click the [Close] button.
6. Click the [OK] button. If a message is displayed
that requests you to restart the personal computer,
click [Yes] to restart the computer.
Setting the file-sharing function
The procedure for setting the file-sharing function
follows, with the “work” folder in drive C: as an
example.
Setting the sharing function
Set the sharing function to make file and/or printer sharing
with other network-connected personal computers valid.
1. Click the [Start] button first and then [My Com-
puter].
2. Double-click [Local disk (C:)].
60
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
3. Right-click the “work” folder (or whichever folder
you want to share), and then click [Sharing and
Security...] in the menu displayed. The [Folder
5. Enter the sharing printer name in [Share name].
6. Click the [OK] button.
Name Properties] window will be displayed.
Confirming connection
After you have finished the network setup operations,
access the folder whose sharing has been set for other
personal computers. Also, confirm the status of the radio
waves in case of trouble such as a network connection
failure.
Setting the file-sharing function for the file
which has been used to execute Network
Setup Wizard is suggested on the screen.
For the wireless LAN, however, since
security is guaranteed by entry of the
network name (SSID) and the network
key, the steps to be taken to set the file-
sharing function easily without using
Network Setup Wizard are given below.
In the case of access point (infrastructure)
connection, enter the necessary data for
the access point before confirming
connection. Refer to the manual of the
access point for the access point setup
procedure.
4. Click [Sharing] if it isn’t already selected.
5. Click the link stating “If you understand the secu-
rity risks, but want to share files without running
the wizard, click here”.
Connecting your personal computer to another
personal computer
1. Click [Start] first and then [My Computer]. The
[My Computer] window will be displayed in the left
frame.
6. Click “Just enable file sharing” and click [OK].
7. Check the [Share this folder on the network] check
box.
2. Click [My Network Places] in the “Other Places”
list. The window [My Network Places] will be dis-
played.
To specify the corresponding folder as a
read-only folder, select the [Read only]
checkbox under the General tab.
3. Click [View workgroup computers] under Network
Tasks in the left frame.
4. Double-click the personal computer to which your
personal computer is to be connected. The folder
that was specified in “Setting the file-sharing func-
tion” on page 60 will be displayed.
8. Click the [OK] button. The folder will be set as a
sharable folder, and the display of the icon for the
“work.” folder will change.
Setting the printer-sharing function
1. Click the [Start] button first and then [Printers and
5. Double-click the folder to be accessed.
FAX]. A list of connected printers will be displayed.
Confirming the status of the radio
1. Right-click the Intel PRO Wireless icon in the lower
right corner of the screen.
2. Right-click the printer for which the sharing func-
tion is to be set, and then click [Sharing] in the
menu displayed. The property window correspond-
2. Click [Open Intel PROSet for Wireless]. The Intel
PROSet for Wireless window opens.
ing to the selected printer will be displayed.
3. Contained within the General tab and the Details
section (accessed by pressing the [Details] button),
you will find the current operating status of the
radio. (When the radio is turned off or the com-
puter is not yet connected, some of the conditions
will not be displayed.)
Setting the printer-sharing function when
Network Setup Wizard has been executed
is suggested on the screen. For the wireless
LAN, however, since security is guaranteed
by entry of the network name (SSID) and
the network key, the steps to be taken to
set the printer-sharing function without
using Network Setup Wizard are laid down
below.
■
Network Name (SSID)
Displays the Network Name (SSID) currently
used by the radio.
■
Profile Name
3. Click the [Sharing] tab.
4. Click [Share this printer].
The current configuration profile is displayed.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
■
Mode
Displays the current operating mode. [Infra-
structure (AP)] or [Ad Hoc] will be displayed.
■
Security
Displays the current security status of the profile
being used:
None: No encryption used.
WEP: WEP encryption algorithm used.
CKIP: WEP encryption algorithm used.
TKIP: WEP encryption algorithm used.
■
Speed
Displays the highest data rate of the associated
access point in mega-bits-per-second (Mbps)
until data transfer occurs.
802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, or
54.
802.11b: 1, 2, 5.5, or 11.
■
Band (Frequency)
Displays the current band and frequency being
used. Displays Out of Range if no band and
frequency is displayed. Displays:
802.11g (2.4 GHz) or 802.11b (2.4 GHz)
■
Channel
Displays the current transmit and receive channel
being used.
■
802.1x Protocol
Displays Enabled if the profile uses 802.1x
authentication. Default is Disabled.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Troubleshooting
Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the
following table.
Problem
Possible Cause
Possible Solution
Incorrect network
name (SSID) or
network key
Ad hoc connection: verify that the network names (SSID’s) and network
keys (WEP) of all computers to be connected have been configured
correctly. SSID’s and WEP key values must be identical on each machine.
Unavailable
network
connection
Access Point (Infrastructure) connection: set the network name (SSID)
and network key to the same values as those of the access point.
Set the Network Authentication value identically to that of the Access
Point. Please consult your network administrator for this value, if
necessary.
Poor radio wave
condition
Ad hoc connection: Retry connection after shortening the distance to
the destination computer or removing any obstacles for better sight.
Access Point (Infrastructure) connection: Retry connection after short-
ening the distance to the access point or removing any obstacles for
better sight.
Radio wave
transmission has
stopped
Check if the wireless switch is turned ON. Also verify “Disable Radio” is
not checked in “Network setting” window.
The computer to be
connected is turned
off
Check if the computer to be connected is turned ON.
Active channel
duplication due to
multiple wireless
LAN networks
If there is any other wireless LAN network nearby, change channels to
avoid active channel duplication.
No right of access to
the network to be
connected
Check if you have a right of access to the network to be connected with.
Check the protocol, work group name or shared setting.
Incorrectly-
performed network
setting
Unmatched
[Network
authentication
(shared mode)]
settings in Windows
XP
If the setting of [Network authentication (shared mode)] is not matched
with that of access point or computer to be connected with, no commu-
nication can be established. Check the parameter setting.
It takes too long to
retrieve the network
and display the
connected
Retrieve computers as follow:
1. Click [Start] button, then click [Search].
2. Click [Computers or people].
computers.
3. Click [Computers on the network].
4. Input the name of computer to be connected with in [Computer
name] and click [Search].
5. Double-click the icon of connected computer.·
63
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
Problem
Possible Cause
Possible Solution
Incorrect setting of IP
address
Check the network setting.
Unavailable
network
connection
“Setting the network” on page 59.
In case of using TCP/IP protocol, you can check IP address as follows:
(continued)
1.
Click [Start] -> [All programs] -> [Accessories] ->
[Command prompt].·
2. In [Command prompt] or [MS-DOS prompt] window, input
[IPCONFIG] command as follows, then press [Enter] key.
Example: In case of C drive being the hard disk:
C:\ipconfig [Enter]
Check that the IP address is correctly displayed:.
IP Address................: 10.0.1.3
Subnet Mask.............: 255.255.255.0
Default Gateway.........: 10.0.1.1
When IP address is displayed as [169.254.XXX.YYY] or [0.0.0.0],
IP address is not correctly fetched from the access point. In that
case, restart the computer itself. If the display is still unchanged,
check the setting of TCP/IP.
If [Cable Disconnected] or [Media Disconnected] is displayed
without showing IP address, check the setting of network name
(SSID) and network key. Also, set the network authentication
according to the access point.
Access control may
be disabled
Check the setting of “Enable network access control using IEEE
802.1X”.
Communication
is disconnected
soon after
connection to
the access point
When restricting the access of wireless LAN clients using IEEE802.1X
authentication, put a check mark on “Enable network access control
using IEEE 802.1X”.
When using at home, remove a check mark on “Enable network access
control using IEEE802.1X”.
For the method of setting related with IEEE802.1X authentication, refer
to the access point manual.
Authentication
method may have
been entered
incorrectly
Re-enter your WEP key and verify that your authentication method
(Open or Shared) is correct.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Wireless LAN Glossary
Access point
the world. A private address is a unique address within a
closed network.
A designation of wireless LAN network configurations.
It indicates a form of communication using an Access
Point. For details, refer to “access point connection” on
page 54.
LAN (Local Area Network)
An environment connecting computers within a rela-
tively small range, such as the same floor and building.
Ad hoc
MAC address (Media Access Control Address)
A designation for wireless LAN network configuration.
It indicates a form of communication limited to those
personal computers which have wireless LAN function.
For details, refer to “Ad hoc connection” on page 54.
A physical address inherent to a network card. For
Ethernet, the top three bytes are controlled/assigned as a
vendor code. The remaining three bytes comprise the
code uniquely (to avoid duplication) controlled by each
vendor. As a result, there is no Ethernet card with the
same physical address in the world. In Ethernet, the
frame transmission/reception is performed based on this
address.
Channel
The frequency band of wireless LAN to be used in
communications over wireless LAN or at the access
point.
MTU (Maximum Transmission Unit)
DHCP (Dynamic Host Configuration Protocol)
The maximum size of data which can be transmitted at
one time in networks including the Internet. In an envi-
ronment whose maximum size of data is too large to
correctly receive data, normal communications can be
restored by setting the size of MTU to a smaller value.
A protocol used for automatically fetching communica-
tion parameters such as IP addresses. The side which
assigns IP address is called DHCP server and the side
that is assigned it is called DHCP client.
DNS (Domain Name System)
Network authentication
A function that controls the correspondence of IP
addresses assigned to a computer with the name. Even
for those computers whose IP addresses are unknown, if
their names are known, it is possible to communicate
with them.
The method of authentication performed by wireless
LAN clients to connect with the access point. There are
two types: open system authentication and shared key
authentication. The type of authentication must be set
to each client and also coincide with the setting of access
point with which to communicate. Network authentica-
tion is sometimes called authentication mode.
IEEE802.11a
One of the wireless LAN standards prescribed by the
802.11 committee in charge of establishing standards of
LAN technology in IEEE (Institute of Electrical and
Electronic Engineers). It allows communications at the
maximum speed of 54 Mbps by using a 5GHz band
which can freely be used without radio communication
license.
Network key
Data that is used for encrypting data in data communi-
cation. The personal computer uses the same network
key both for data encryption and decryption, therefore,
it is necessary to set the same network key as the other
side of communication.
IEEE802.11b
Network name (SSID: Service Set Identifier)
One of the wireless LAN standards prescribed by the
802.11 committee in charge of establishing standards of
LAN technology in IEEE (Institute of Electrical and
Electronic Engineers). It allows communications at the
maximum speed of 11Mbps by a band of 2.4 GHz (ISM
band) which can freely be used without radio communi-
cation license.
The network name is a unique identifier attached to the
WLAN packet header that acts as a password when the
client attempts to connect to a WLAN. The SSID differ-
entiates one WLAN from another so all WLAN devices
attempting to connect to a specific WLAN must use the
same SSID. SSID’s are transmitted in cleartext, thus
supplying no security to the WLAN.
IP address
An address used by computers for communicating in
TCP/IP environment. IP addresses have global and
private addresses. A global address is a unique address in
65
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
Open system authentication
An 802.11 wireless LAN authentication method. Open
System does not exchange any key or other information,
it is a simple request by the mobile station to be authen-
ticated without verifying identity.
PPPoE (Point to Point Protocol over Ethernet)
A method of allowing the authentication protocol
adopted in telephone line connection (PPP) to be used
over an Ethernet.
Protocol
A procedure or rule of delivering data among
computers. Ordered data communication is allowed by
making all conditions required for communication
including the method of data transmission/reception
and actions upon communication errors into proce-
dures.
Shared key authentication
An 802.11 wireless LAN authentication method. When a
client attempts to associate to an access point, the access
point will send a challenge to the client. The client
encrypts the challenge with the network key and sends it
back to the access point. If the access point can decrypt
the challenge, then authentication has succeeded.
SSID (Service Set Identifier)
See “Network name”
Subnet mask
TCP-IP network is controlled by being divided into
multiple smaller networks (subnets). IP address consists
of the subnet address and the address of each computer.
Subnet mask defines how many bits of IP address
comprise the subnet address. The same value shall be set
among computers communicating with each other.
TCP/IP (Transmission Control Protocol/Internet
Protocol)
A standard protocol of the Internet.
Wi-Fi
Short for “Wireless Fidelity”. A term meant to be used
generically when referring to any type of 802.11
network, whether 802.11b, 802.11a, 802.11g, etc.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
IP address information
IP addressing is much more complicated
than can be briefly explained in this
document. You are advised to consult with
your network administrator for additional
information.
If IP address is unknown, set IP address as follows:
If you have an access point (DHCP server) on the
network, set the IP address as follows:
[Obtain an IP address automatically]
A DHCP server is a server that
automatically assigns IP addresses to
computers or other devices in the network.
There is no DHCP server for the AdHoc
network.
If the IP address is already assigned to the computer in
the network, ask the network administrator to check the
IP address to be set for the computer.
If no access point is found in the network:
An IP address is expressed with four values in the range
between 1 and 255.
Set the each computer as follows: The value in paren-
theses is a subnet mask.
<Example>
Computer A: 192.168.100.2 (255.255.255.0)
Computer B: 192.168.100.3 (255.255.255.0)
Computer C: 192.168.100.4 (255.255.255.0)
:
:
Computer X: 192.168.100.254 (255.255.255.0)
67
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
Specifications
Item
Specifications
Type of network
Transfer rate
Conforms to IEEE 802.11a/802.11b/g (Wi-Fi based)*
(Automatic switching)
54 Mbps maximum data rate
Active frequency
802.11b/g: 2400~2473 MHz
802.11a: 4900 ~ 5850 MHz
Number of channels
Typical operating distances**
802.11a: 8 independent channels
802.11b/g: 11 channels, 3 non-overlapping channels
802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps
802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps
802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps
Security
Encryption Types - WEP, TKIP, AES***
WPA 1.0, WPA-2 compliant
Encryption Key lengths Supported: 64 bits and 128 bits
802.1x/EAP
Maximum recommended number of computers to
be connected over wireless LAN (during ad hoc
connection)
10 units or less ****
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of
wireless LAN (Wi-Fi Alliance) has been passed.
** The communication ranges shown above will increase or decrease depending on factors such as number of walls,
reflective material, or interference from external RF sources.
*** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/
104 bits after subtracting the fixed length of 24 bits.
**** Depending on practical environments, the allowable number of computers to be connected may be decrease
68
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Using the Bluetooth Device
The Integrated Bluetooth module (EYTF3CSFT) is an
optional device available for Fujitsu mobile computers.
WHAT IS BLUETOOTH?
Bluetooth technology is designed as a short-range
wireless link between mobile devices, such as laptop
computers, phones, printers, and cameras. Bluetooth
technology is used to create Personal Area Networks
(PANs) between devices in short-range of each other.
WHERE TO FIND INFORMATION ABOUT
BLUETOOTH
The Bluetooth module contains a robust Help user’s
guide to assist you in learning about operation of the
Bluetooth device.
To access the Help file, click [Start] -> All Programs, and
click on Toshiba. Select Bluetooth, then select User’s
Guide.
For additional information about Bluetooth Technology,
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
The transmitters in this device must not be co-located or
operated in conjunction with any other antenna or trans-
mitter.
Canadian Notice
To prevent radio interference to the licensed service, this
device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject
to licensing.
Warranty
Users are not authorized to modify this product. Any
modifications invalidate the warranty.
This equipment may not be modified, altered, or changed
in any way without signed written permission from
Fujitsu. Unauthorized modification will void the equip-
ment authorization from the FCC and Industry Canada
and the warranty.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
A
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Security Device*
User’s Guide
* Availability varies by model
71
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
B
72
Download from Www.Somanuals.com. All Manuals Search And Download.
S e c u r i t y D e v i c e U s e r ’s G u i d e
INSTALLING OMNIPASS
Fingerprint Sensor Device
If OmniPass has already been installed on your system,
skip this section and go directly to “User Enrollment” on
page 74. You can determine whether OmniPass has
already been installed by checking to see if the following
are present:
INTRODUCING THE
FINGERPRINT SENSOR DEVICE
Your system may have a fingerprint sensor device on the
side of the display opposite the function buttons. The
device is a standard feature on 12.1” models; it is not
available on 10.4” models. (See Figure 1-2 on page 6 for
location)
■
The presence of the gold key-shaped OmniPass icon in
the system tray at the bottom right of the screen.
The presence of the Softex program group in the
■
Programs group of the Start menu
System Requirements
The OmniPass application requires space on your hard
drive; it also requires specific Operating Systems (OS’s).
The minimum requirements are as follows:
■
Windows XP Home Edition, Windows XP Profes-
sional or Windows 2000 operating system
At least 35 MB available hard disk space
■
Installing the OmniPass Application
Figure B-1 Fingerprint sensor
If OmniPass is already installed on your system, go to
“User Enrollment” on page 74. (If you have run the
ClickMe! utility, it is likely that OmniPass has already
been installed on your system.) Otherwise continue with
this section on software installation.
With a fingerprint sensor, you can avoid having to enter
a username and password every time you want to:
■
Log onto Windows
■
Recover from Standby mode
For installation, OmniPass requires that the
user installing OmniPass have
administrative privileges to the system. If
your current user does not have
■
Cancel a password-protected screen saver
■
Log into homepages that require a username and pass-
word
administrative privileges, log out and then
log in as an administrator before
proceeding with OmniPass installation.
After you have “enrolled” - or registered - your finger-
print, you can simply swipe your fingertip over the
sensor for the system to recognize you.
To install OmniPass on your system you must:
The fingerprint sensor uses Softex OmniPass which
provides password management capabilities to
Microsoft Windows operating systems. OmniPass
enables you to use a "master password" for all Windows,
applications, and on-line passwords.
1. Insert the installation media for the OmniPass
application into the appropriate drive. If you are
installing from CD-ROM or DVD-ROM, you must
find and launch the OmniPass installation program
(setup.exe) from the media.
The use of OmniPass results in a secure authentication
system for restricting access to your computer, applica-
tions, websites, and other password-protected resources.
2. Follow the directions provided in the OmniPass
installation program. Specify a location to which
you would like OmniPass installed. It is recom-
mended that you NOT install OmniPass in the root
directory (e.g. C:\).
OmniPass presents a convenient graphical user inter-
face, through which you can securely manage pass-
words, users, and multiple identities for each user.
3. Once OmniPass has completed installation you will
be prompted to restart you system. Once your
system has rebooted you will be able to use
OmniPass. If you choose not to restart immediately
after installation, OmniPass will not be available for
use until the next reboot.
GETTING STARTED
This section guides you through the preparation of your
system for the OmniPass fingerprint recognition
application. You will be led through the OmniPass
installation process. You will also be led through the
procedure of enrolling your first user into OmniPass.
The installation program automatically places an icon
(Softex OmniPass) in the Windows Control Panel as
well as a golden key shaped icon in the taskbar.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
B
Verifying Information about OmniPass
After you have completed installing OmniPass and
restarted your system, you may wish to check the version
of OmniPass on your system.
5. Once OmniPass has finished uninstalling, reboot
your system when prompted.
USER ENROLLMENT
Before you can use any OmniPass features you must first
enroll a user into OmniPass.
To check the version information of OmniPass:
1. From the Windows Desktop, double-click the key-
shaped OmniPass icon in the taskbar (usually
located in the lower right corner of the screen),
or,
Master Password Concept
Computer resources are often protected with passwords.
Whether you are logging into your computer, accessing
your email, e-banking, paying bills online, or accessing
network resources, you often have to supply credentials
to gain access. This can result in dozens of sets of creden-
tials that you have to remember.
Click the Start button, select Settings, and click
Control Panel (if you are using Windows XP you
will see the Control Panel directly in the Start menu;
click it, then click Switch to Classic View). Double-
click Softex OmniPass in the Control Panel, and the
OmniPass Control Center will appear. If it does not
appear, then the program is not properly installed,
During OmniPass user enrollment a "master password”
is created for the enrolled user. This master password
“replaces” all other passwords for sites you register with
OmniPass.
or,
Example: A user, John, installs OmniPass on his system
(his home computer) and enrolls an OmniPass user with
username “John_01” and password “freq14”. He then
goes to his webmail site to log onto his account. He
inputs his webmail credentials as usual (username
“John_02” and password “tablet”), but instead of
clicking [Submit], he directs OmniPass to Remember
Password. Now whenever he returns to that site,
OmniPass will prompt him to supply access credentials.
Click the Start button, select Programs, and from
the submenu select the Softex program group, from
that submenu click OmniPass Control Center.
2. Select the About tab at the top of the OmniPass
Control Panel. The About tab window appears with
version information about OmniPass.
Uninstalling OmniPass
John enters his OmniPass user credentials (“John_01”
and “freq14”) in the OmniPass authentication prompt,
and he is allowed into his webmail account. He can do
this with as many websites or password protected
resources he likes, and he will gain access to all those
sites with his OmniPass user credentials (“John_01” and
“freq14”). This is assuming he is accessing those sites
with the system onto which he enrolled his OmniPass
user. OmniPass does not actually change the credentials
of the password protected resource. If John were to go to
an Internet cafe to access his webmail, he would need to
enter his original webmail credentials (“John_02” and
“tablet”) to gain access. If he attempts his OmniPass user
credentials on a system other than where he enrolled
that OmniPass user, he will not gain access.
Before you uninstall the software, decrypt
all OmniPass encrypted files and export all
OmniPass User Profiles. Failure to do so
may result in permanent loss of encrypted
file data, and permanent loss of all
remembered passwords and associated
information (see Chapter 5 of the
OmniPass help document:: Exporting and
Importing Users).
For uninstallation, OmniPass requires that
the user uninstalling OmniPass have
administrative privileges to the system. If
your current user does not have
administrative privileges, log out and then
log in as an administrator before
The basic enrollment procedure assumes
you have no hardware authentication
devices or alternate storage locations that
you wish to integrate with OmniPass. If
you desire such functionality, consult the
appropriate sections after reviewing this
section.
proceeding with OmniPass uninstallation.
To remove the OmniPass application from your system:
1. Click Start on the Windows taskbar. Select Settings,
and then Control Panel.
2. Double-click Add/Remove Programs.
3. Select OmniPass, and then click Change/Remove.
4. Follow the directions to uninstall the OmniPass
application.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
S e c u r i t y D e v i c e U s e r ’s G u i d e
Basic Enrollment
before OmniPass acquires your fingerprint. Should
OmniPass fail to acquire your fingerprint, or if the
capture screen times out, click [Back] to restart the
fingerprint enrollment process.
The Enrollment Wizard will guide you through the
process of enrolling a user. Unless you specified other-
wise, after OmniPass installation the Enrollment Wizard
will launch on Windows login. If you do not see the
Enrollment Wizard, you can bring it up by clicking Start
on the Windows taskbar; select Programs; select Softex;
click OmniPass Enrollment Wizard.
Your system has a “swipe” fingerprint sensor. A swipe
sensor is small and resembles a skinny elongated rect-
angle. To capture a fingerprint, gently swipe or pull
your fingertip over the sensor (starting at the second
knuckle) in the direction of the arrow. Swiping too
fast or too slow will result in a failed capture. The
Choose Finger screen has a [Practice] button; click it
to practice capturing your fingerprint. When you are
comfortable with how your fingerprint is captured,
proceed to enroll a finger.
1. Click Enroll to proceed to username and password
verification. By default, the OmniPass Enrollment
Wizard enters the credentials of the currently logged
in Windows user.
2. Enter the password you use to log in to Windows.
This will become the “master password” for this
OmniPass user. In most cases, the Domain: value will
be your Windows computer name. In a corporate
environment, or when accessing corporate resources,
the Domain: may not be your Windows computer
name. Click [Next] to continue.
3. Once OmniPass has successfully acquired the finger-
print, the Verify Fingerprint screen will automati-
cally appear. To verify your enrolled fingerprint, place
your fingertip on the sensor and hold it there as if
you were having a fingerprint captured. Successful
fingerprint verification will show a green fingerprint
in the capture window and the text Verification
Successful under the capture window.
3. In this step OmniPass captures your fingerprint.
Refer to “Enrolling a Fingerprint” on page 75 for
additional information.
4. Next, choose how OmniPass notifies you of various
events. We recommend you keep Taskbar Tips on
Beginner mode taskbar tips and Audio Tips on at
least Prompt with system beeps only until you get
accustomed to how OmniPass operates. Click [Next]
to proceed with user enrollment. You will then see a
Congratulations screen indicating your completion
of user enrollment.
USING OMNIPASS
You are now ready to begin using OmniPass. Used regu-
larly, OmniPass will streamline your authentication
procedures.
Password Replacement
You will often use the password replacement function.
When you go to a restricted access website (e.g., your
bank, your web-based email, online auction or payment
sites), you are always prompted to enter your login
credentials. OmniPass can detect these prompts and you
can teach OmniPass your login credentials. The next time
you go to that website, you can authenticate with your
fingerprint to gain access.
5. Click [Done] to exit the OmniPass Enrollment
Wizard. You will be asked if you’d like to log in to
OmniPass with your newly enrolled user; click [Yes].
Enrolling a Fingerprint
Enrolling a fingerprint will increase the security of your
system and streamline the authentication procedure.
OmniPass Authentication Toolbar
You enroll fingerprints in the OmniPass Control Center.
With an OmniPass user logged in, double-click the
system tray OmniPass icon. Select the User Settings tab
and click Enrollment under the User Settings area. Click
Enroll Authentication Device and authenticate at the
authentication prompt to start device enrollment.
After installing OmniPass and restarting, you will notice
a dialog you have not seen before at Windows Logon.
This is the OmniPass Authentication Toolbar, and it is
displayed whenever the OmniPass authentication system
is invoked. The OmniPass authentication system may be
invoked frequently: during Windows Logon, during
OmniPass Logon, when unlocking your workstation,
when resuming from standby or hibernate, when
unlocking a password-enabled screensaver, during pass-
word replacement for remembered site or application
logins, and more. When you see this toolbar, OmniPass is
prompting you to authenticate.
1. During initial user enrollment, you will be prompted
to select the finger you wish to enroll. Fingers that
have already been enrolled will be marked by a green
check. The finger you select to enroll at this time will
be marked by a red arrow. OmniPass allows you to
re-enroll a finger. If you choose a finger that has
already been enrolled and continue enrollment,
OmniPass will enroll the fingerprint, overwriting the
old fingerprint. Select a finger to enroll and click
[Next].
The Logon Authentication window indicates what
OmniPass-restricted function you are attempting. The
icons in the lower left (fingerprint and key) show what
authentication methods are available to you. Selected
authentication methods are highlighted while unselected
2. It is now time for OmniPass to capture your selected
fingerprint. It may take a several capture attempts
75
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
B
methods are not. When you click the icon for an unse-
lected authentication method, the authentication
prompt associated with that method is displayed.
This setting is more convenient in that
whenever you go to a site remembered
with this setting, you will bypass any
authentication procedure and gain instant
access to the site. But should you leave
your system unattended with your
OmniPass user logged in, anyone using
your system can browse to your password
protected sites and gain automatic access.
When prompted to authenticate, you must supply the
appropriate credentials: an enrolled finger for the finger-
print capture window or your master password for the
master password prompt (the key icon).
Remembering a Password
OmniPass can remember any application, GUI, or pass-
word protected resource that has a password prompt.
If you uncheck both boxes in Settings for this Password
Site, OmniPass will prompt you for your master pass-
word or fingerprint authentication device. Once you
have authenticated with OmniPass your credentials will
be filled in to the site login prompt, but you will have to
click the website [OK], [Submit], or [Login] button to
gain access to the site.
Using the following procedure, you can store a set of
credentials into OmniPass. These credentials will then be
linked to your “master password” or fingerprint.
Go to a site that requires a login (username and pass-
word), but do not log in yet. At the site login prompt,
enter your username and password in the prompted
fields, but do not enter the site (do not hit [Enter],
[Submit], [OK], or Login). Right-click the OmniPass
system tray icon and select Remember Password from
the submenu. The Windows arrow cursor will change to
a golden key OmniPass cursor. Click this OmniPass
cursor in the login prompt area, but do not click the
[Login] or [Submit] button.
Click Finish to complete the remember password proce-
dure. The site location, the credentials to access the site,
and the OmniPass authentication settings for the site are
now stored in the OmniPass secure database. The
OmniPass authentication settings (Settings for this Pass-
word Site) can always be changed in Vault Management.
Logging in to a Remembered Site
Whether or not OmniPass prompts you to authenticate
when you return to a remembered site is determined by
Settings for this Password Site and can be changed in
Vault Management.
Associating a Friendly Name
After clicking the OmniPass key cursor near the login
prompt, OmniPass will prompt you to enter a “friendly
name” for this site. You should enter something that
reminds you of the website, the company, or the service
you are logging into. In its secure database, OmniPass
associates this friendly name with this website.
The following cases are applicable to using OmniPass to
login to: Windows, remembered websites, and all other
password protected resources.
With Master Password
Additional Settings for Remembering a Site
Once you return to a site you have remembered with
OmniPass, you may be presented with a master pass-
word prompt. Enter your master password and you will
be allowed into the site.
When OmniPass prompts you to enter a “friendly name”
you also have the opportunity to set how OmniPass
authenticates you to this site. There are three effective
settings for how OmniPass handles a remembered site.
Logging into Windows with a Fingerprint Device
When logging into Windows with a fingerprint device,
the fingerprint capture window will now appear next to
the Windows Login screen. Place your enrolled fingertip
on the sensor to authenticate. You will be simultaneously
logged into Windows and OmniPass. The capture
window will also appear if you have used Ctrl-Alt-Del to
lock a system, and the fingerprint device can be used to
log back in as stated above.
The default setting is Automatically click the “OK” or
“Submit” button for this password protected site once
the user is authenticated. With this setting, each time
you navigate to this site OmniPass will prompt you for
your master password or fingerprint authentication
device. Once you have authenticated with OmniPass,
you will automatically be logged into the site.
Less secure is the option to Automatically enter this
password protected site when it is activated. Do not
prompt for authentication. Check the upper box to get
this setting, and each time you navigate to this site
OmniPass will log you into the site without prompting
you to authenticate.
If a machine is locked and OmniPass
detects a different user logging back in
with a fingerprint, the first user will be
logged out and the second user logged in.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
S e c u r i t y D e v i c e U s e r ’s G u i d e
In Windows XP, your login options must be set either for
classic login, or for fast user switching and logon screen
to be enabled to use your fingerprint to log on to
Windows. To change this go to Control Panel, select
User Accounts and then click Change the way users log
on or off. If your Windows screensaver is password
protected, the fingerprint capture window will now
appear next to screensaver password dialog during
resume. You can authenticate to your screensaver pass-
word prompt with your enrolled finger.
To add a new identity, click New Identity or double-click
Click here to add a new identity. Name the new identity
and click [OK], then click [Apply]. You can now switch
to the new identity and start remembering passwords.
To delete an identity, highlight the identity you want to
delete and click [Delete Identity], then click [Apply].
When you delete an identity, all of its
associated remembered sites and password
protected dialogs are lost.
Password Management
OmniPass provides an interface that lets you manage
your passwords. To access this GUI, double-click the
OmniPass key in the system tray. Click Vault Manage-
ment; you will be prompted to authenticate. Once you
gain access to Vault Management, click Manage Pass-
words under Vault Settings. You will see the Manage
Passwords interface, with a list of friendly names.
To set the default identity, highlight the identity you
want as default and click [Set as Default]; click [Apply]
to ensure the settings are saved. If you log in to
OmniPass with a fingerprint device, you will automati-
cally be logged in to the default identity for that
OmniPass user. You can choose the identity with which
you are logging in if you login using "master password".
You can view the credentials stored for any remembered
website by highlighting the desired resource under Pass-
word Protected Dialog and clicking Unmask Values.
Should a password be reset, or an account expire, you
can remove stored credentials from OmniPass. Highlight
the desired resource under Password Protected Dialog
and click Delete Page. You will be prompted to confirm
the password deletion.
Choosing User Identity during Login
To choose your identity during login, type your user-
name in the User Name: field. Press [Tab] and see that
the Domain: field self-populates. Click the Password:
field to bring the cursor to it, and you will see the pull-
down menu in the Identity: field. Select the identity you
wish to login as and then click OK to login.
Switch User Identity
The two check boxes in Manage Passwords govern
whether OmniPass prompts you to authenticate or
directly logs you into the remembered site.
To switch identities at any time, right-click the
OmniPass system tray icon and click Switch User Iden-
tity from the submenu. The Switch Identity dialog will
appear. Select the desired identity and then click OK.
OmniPass will overwrite an old set of credentials for a
website if you attempt to use Remember Password on an
already remembered site.
Identities and Password Management
On the Manage Passwords interface of the Vault
Management tab of the OmniPass Control Center, there
is a pull-down selection box labeled, Identity. This field
lets you choose which identity you are managing pass-
words for. When you select an identity here, only those
password protected dialogs that are associated with that
identity are shown. You can perform all the functions
explained in “Password Management” on page 77.
The exception to the above rule is the resetting of your
Windows password. If your password is reset in
Windows, then the next time you login to Windows,
OmniPass will detect the password change and prompt
you to “Update” or “Reconfirm” your password with
OmniPass. Enter your new Windows password in the
prompt(s) and click OK and your OmniPass "master
password" will still be your Windows password.
CONFIGURING OMNIPASS
This section gives an overview of both the Export/
Import function and the OmniPass Control Center.
OmniPass User Identities
Identities allow OmniPass users to have multiple
[email protected]). If OmniPass did not provide
you identities, you would be limited to remembering
one account per site.
Exporting and Importing Users
Using the OmniPass Control Center, you can export and
import users in and out of OmniPass. The export
process backs up all remembered sites, credentials, and
any enrolled fingerprints for an OmniPass user. All
OmniPass data for a user is backed up to a single
encrypted database file. During the import process, the
Windows login of the exported user is required. If the
proper credentials cannot be supplied, the user profile
will not be imported.
To create and manage identities, double-click the
OmniPass key in the system tray. Click Vault Manage-
ment; OmniPass will prompt you to authenticate. Once
you gain access to Vault Management, click Manage
Identities under Vault Settings. You can only manage
the identities of the currently logged in OmniPass user
77
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
B
Things to Know Regarding Import/Export
Assume you export a local Windows User profile from
■
You should periodically export your user
■
profile and store it in a safe place. If
anything happens to your system, you
can import your OmniPass profile to a
new system and have all your remem-
bered settings and fingerprints instantly.
OmniPass. You want to import that profile to another
machine that has OmniPass. Before you can import
the profile, a Windows user with the same login cre-
dentials must be created on the machine importing the
profile.
■
When you examine the importation, you
are prompted for authentication. The
credentials that will allow a user profile
to be imported are the Windows login
credentials of the exported user. They
are the credentials that had to be
submitted when the user profile was
exported. You will need User Name,
Password, and Domain.
Example: I have a Windows user with the username
“Tom” and the password “Sunshine” on my system. I
have enrolled Tom into OmniPass and remembered
passwords. I want to take all my passwords to new sys-
tem. I export Tom’s OmniPass user profile. I go to my
new system and using the Control Panel I create a user
with the username "Tom" and the password "Sun-
shine". I can now successfully import the OmniPass
user data to the new system.
Exporting an OmniPass User Profile
To export a user, open the OmniPass Control Center,
■
and click Import/Export User under Manage Users.
If you export an OmniPass-only user, you can import
that user to any computer running OmniPass, pro-
vided that a user with that name is not already
enrolled in OmniPass.
Click Exports an OmniPass user profile. OmniPass will
prompt you to authenticate. Upon successfully authenti-
cation, you must name the OmniPass user profile and
decide where to save it. An .opi file is generated, and you
should store a copy of it in a safe place.
■
If you attempt to import a user profile who has the
same name as a user already enrolled in OmniPass, the
OmniPass import function will fail.
This .opi file contains all your user specific OmniPass
data, and it is both encrypted and password protected.
This user profile does NOT contain any of your
encrypted data files.
OMNIPASS CONTROL CENTER
This section will serve to explain functions within the
OmniPass Control Center that weren’t explained earlier.
Importing an OmniPass User Profile
You can access the OmniPass Control Center any of
three ways:
You cannot import a user into OmniPass if
there already is a user with the same name
enrolled in OmniPass.
■
Double-click the golden OmniPass key shaped icon in
the Windows system tray (typically in the lower-right
corner of the desktop)
■
Click the Start button; select the Programs group;
To import an OmniPass user open the OmniPass
Control Center, and click Import/Export User under
Manage Users. Click Imports a new user into OmniPass
and then select OmniPass Import/Export File (*.opi)
and click Next. OmniPass will then prompt you to
browse for the file you had previously exported (.opi
file). When you select the .opi file for importation,
OmniPass will prompt you for authentication. The
credentials that will allow a user profile to be imported
are the Windows login credentials of the exported user.
They are the credentials that had to be submitted when
the user profile was exported. You will need User Name,
Password, and Domain. If you don’t remember the value
for Domain, in a PC or SOHO environment Domain
should be your computer name.
select the Softex program group; and click the
OmniPass Control Center selection.
■
Open the Windows Control Panel (accessible via Start
button --> Settings --> Control Panel) and double-
click the Softex OmniPass icon.
User Management
The User Management tab has two major interfaces:
Add/Remove User and Import/Export User. Import/
Export User functionality is documented in “Exporting
and Importing Users” on page 77. Add/Remove User
functionality is straightforward.
If you click Adds a new user to OmniPass you will start
the OmniPass Enrollment Wizard. The Enrollment
Wizard is documented in “User Enrollment” on page 74.
OmniPass will notify you if the user was successfully
imported.
If you click Removes a user from OmniPass, OmniPass
will prompt you to authenticate. Authenticate with the
78
Download from Www.Somanuals.com. All Manuals Search And Download.
S e c u r i t y D e v i c e U s e r ’s G u i d e
credentials (or enrolled fingerprint) of the user you wish
to remove. OmniPass will prompt you to confirm user
removal. Click OK to complete user removal.
TROUBLESHOOTING
You cannot use OmniPass to create Windows users. You
must first create the Windows user, and you will need
administrative privileges to do that. Once the Windows
user is created, you can add that user to OmniPass using
the same username and password
Removing a user will automatically destroy
all OmniPass data associated with that
user. All identities and credentials
associated with the user will be lost. If you
are sure about removing the user, we
recommend you export the user profile.
Cannot add Windows users to OmniPass
If you experience difficulties adding a Windows user
to OmniPass, you may need to adjust your local secu-
rity settings. You can do this by going to Start,
Control Panel, Administrative Tools, and Local
Security Settings. Expand Local Policies, expand
Security Options, and double-click Network Access:
Sharing and Security Model for Local Accounts. The
correct setting should be Classic - Local Users Authen-
ticate as Themselves.
User Settings
The User Settings tab has four interfaces: Audio Settings,
Taskbar Tips, and Enrollment. User settings allow users
to customize OmniPass to suit their individual prefer-
ences. Under User Settings (Audio Settings and Taskbar
Tips) you can set how OmniPass notifies the user of
OmniPass events (e.g., successful login, access denied,
etc.). The details of each setting under the Audio
Settings and Taskbar Tips interfaces are self-explana-
tory.
Cannot add a User with a Blank Password to OmniPass
If you experience difficulties adding a user with a
blank password to OmniPass, you may need to adjust
your local security settings. First attempt the proce-
dure explained in the Cannot add Windows user to
OmniPass section. If the difficulties persist, then try
the following procedure.
The Enrollment interface allows you to enroll finger-
prints. To enroll additional fingerprints, click Enroll
Authentication Device, and authenticate with
OmniPass. Select the fingerprint recognition device in
the Select Authentication Device screen (it should
already be marked by a green check if you have a finger
enrolled) and click Next.
Click Start, Control Panel, Administrative Tools,
and Local Security Settings. Expand Local Policies,
expand Security Options, and double-click
Accounts: Limit local account use of blank pass-
words to console login only. This setting should be
set to Disabled.
System Settings
The OmniPass Startup Options interface can be found
in the System Settings tab. With these options you can
specify how your OmniPass Logon is tied to your
Windows Logon.
Dialog appears after OmniPass authentication during
Windows Logon
After installing OmniPass on your system, you can
choose to logon to Windows using OmniPass. You
authenticate with OmniPass (via master password, or
an enrolled security device) and OmniPass logs you
into Windows. You may, during this OmniPass
authentication, see a Login Error dialog box.
The first option, Automatically log on to OmniPass as
the current user, will do just as it says; during Windows
login, you will be logged on to OmniPass using your
Windows login credentials. If the user logging into
Windows was never enrolled into OmniPass, upon login
no one will be logged on to OmniPass. This setting is
appropriate for an office setting or any setting where
users must enter a username and password to log into a
computer. This is the default setting.
This dialog box occurs when OmniPass was unable to
log you into Windows with the credentials supplied
(username and password). This could happen for any
of the following reasons:
With the second option, Manually log on to OmniPass
at startup, OmniPass will prompt you to login once you
have logged on to Windows.
■
Your Windows password has changed
Your Windows account has been disabled
■
If you are having difficulties due to the first reason,
you will need to update OmniPass with your changed
Windows account password. Click Update Password
and you will be prompted with a dialog to reconfirm
your password.
With the third option, Do not log on to OmniPass at
startup, OmniPass will not prompt for a user to be
logged on.
You can manually log on to OmniPass by right-clicking
the OmniPass system tray icon and clicking Log in User
from the right-click menu.
Enter the new password to your Windows user
account and click OK. If the error persists, then it is
unlikely the problem is due to your Windows user
account password changing.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e
–
A p p e n d i x
B
Trusted Platform Module Installation
This disc contains several utilities that allow you to
enhance the security of your system using the optional
Trusted Platform Module (TPM) contained in the sys-
tem. TPM is a Trusted Computing Group (TCG)-com-
pliant embedded security chip that allows computers to
run applications more securely and to make transactions
and communications more trustworthy. TPM is an
important component of the Fujitsu Security Platform.
3. Open the Security menu, scroll down to Set Super-
visor Password, and enter a password (if not already
set).
4. While in the Security menu, scroll down to Security
Chip Setting, and click on it. The Security Chip Set-
ting submenu will appear.
5. Click on Security Chip to enable it.
6. Click [F10] to save changes and exit.
Installing the TPM Applications
1. Insert the “Trusted Platform Module Drivers and
• The use of this disc requires that you
have a device capable of reading CDs
attached to your system. If you do not
have a built-in CD or DVD player, you
will need to attach an external player.
Applications CD” in the drive.
2. The setup program should start the installation
automatically. If the installation does not start
automatically, go to the setup.exe file on the disc
and double-click on it.
• The use of this disc also requires a
device capable of writing to removable
media (such as a floppy disk drive, CD-
RW drive, or PCMCIA memory card).
This drive will be used to store the
Emergency Recovery Token file and -- if
desired -- the Emergency Recovery
Archive file. For more information on
available external devices, visit our
website at: us.fujitsu.com/computers.
3. Follow the instructions that appear on your screen
to load the drivers and applications for TPM.
4. After loading the software, you will be prompted to
reboot your system. Remove the CD from the drive,
then reboot.
5. After rebooting, the Security Platform Installation
Wizard will open and lead you through the setup
and customization of the TPM applications.
When installing the software, be sure to
create Emergency Recovery Archive and
Emergency Recovery Token files when
prompted by the Security Platform
Initialization Wizard. These files will be
necessary in the event of hardware failure.
Failure to create these files could result in
a loss of the Security Platform owner key,
which is the physical root for secrets as
well as the logical root for all Security
Platform user-specific keys. The
Getting Help
■
For detailed help about installing the TPM applica-
tions, go to the readme.txt file on the disc.
■
For in-depth help and information about the TPM
applications, double-click on the Security Platform
icon in the system tray, and click {Getting Started
Guide].
Initialization Wizard provides step-by-step
instructions for creating the files.
Procedure
Be sure you have a built-in or external drive attached to
your system that can read CDs. You will also need a
means to write to removable media during the installa-
tion.
Enabling the Security Chip in BIOS
1. Before installing the TPM software, you will need to
enable the security chip in the system BIOS. To do
so:
•
If your system is running, click [Start] -> Shut
Down, and select Restart. Click [OK].
•
If the system is not running, power it up.
2. When the Fujitsu logo appears, press the [F2] but-
ton. The BIOS Setup Utility will appear.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
I n d e x
Index
Click Me! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
configuring peripherals interface . . . . . . . . . . . . . . . .42
connectors and peripheral interfaces . . . . . . . . . . . . .20
conserving battery power . . . . . . . . . . . . . . . . . . . . . . .32
conventions used in the guide . . . . . . . . . . . . . . . . . . . .1
critically low battery level . . . . . . . . . . . . . . . . . . . . . . .28
cursor not tracking pen . . . . . . . . . . . . . . . . . . . . . . . .41
A
adjusting the display brightness . . . . . . . . . . . . . . . . . 29
air flow vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
application buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
application A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
application B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ctl-Alt-Del button . . . . . . . . . . . . . . . . . . . . . . . . . 13
display mode button . . . . . . . . . . . . . . . . . . . . . . . . 13
EMail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
enter button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
escape button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fujitsu Menu Utility . . . . . . . . . . . . . . . . . . . . . . . . 14
function button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
orientation button . . . . . . . . . . . . . . . . . . . . . . . . . 13
security button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
tertiary functions . . . . . . . . . . . . . . . . . . . . . . . . 16, 17
D
DC input connector . . . . . . . . . . . . . . . . . . . . . . . . .9, 20
DIMM card, removing . . . . . . . . . . . . . . . . . . . . . . . . .35
display
screen is blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
screen, cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Drivers and Application Restore CD . . . . . . . . . . . . .42
Automatically Downloading Driver Updates . . . . . . 43
E
B
external monitor connector . . . . . . . . . . . . . . . . . . . . . .9
battery gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 31
battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
F
battery pack
FDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19, 43
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
critically low level . . . . . . . . . . . . . . . . . . . . . . . . . . 28
low-battery warning . . . . . . . . . . . . . . . . . . . . . . . . 28
no memory effect . . . . . . . . . . . . . . . . . . . . . . . . . . 32
overcharge protection . . . . . . . . . . . . . . . . . . . . . . . 31
removing and installing . . . . . . . . . . . . . . . . . . . . . 32
will not begin charging . . . . . . . . . . . . . . . . . . . . . . 31
fingerprint sensor device . . . . . . . . . . . . . . . . . . . . .6, 73
enrolling a fingerprint . . . . . . . . . . . . . . . . . . . . . . .75
importing an OmniPass user profile . . . . . . . . . . . .78
installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . .73
introducing the fingerprint sensor device . . . . . . .73
using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
verifying information about OmniPass . . . . . . . . .74
battery power
conserving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
used in Standby mode . . . . . . . . . . . . . . . . . . . . . . 28
Fujitsu contact information . . . . . . . . . . . . . . . . . . . . . .1
Fujitsu Driver Update utility . . . . . . . . . . . . . . . . .19, 43
battery release latch . . . . . . . . . . . . . . . . . . . . . . . . . 7, 21
BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17
BOOT Priority Change . . . . . . . . . . . . . . . . . . . . . . . . 42
bridge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
built-in microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
H
headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 20
Hibernate (Save-to-Disk) mode . . . . . . . . . . . . . .25, 28
I
idle state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
IEEE 1394 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 21
infrared data transfer not working . . . . . . . . . . . . . . .41
infrared keyboard port . . . . . . . . . . . . . . . . . 6, 8, 10, 20
Installing a Memory Stick . . . . . . . . . . . . . . . . . . . . . .33
interfaces, connectors and peripherals . . . . . . . . . . . .20
C
calibrating the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 39
charge/DC input icon . . . . . . . . . . . . . . . . . . . . . . . . . 11
charging the battery pack . . . . . . . . . . . . . . . . . . . . . . 31
cleaning the display screen . . . . . . . . . . . . . . . . . . . . . 41
81
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C
powering up the pen tablet . . . . . . . . . . . . . . . . . . . . .26
problems, solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
protecting the display screen . . . . . . . . . . . . . . . . . . . .39
L
LAN jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Local Area Network (LAN) . . . . . . . . . . . . . . . . . . . . 21
Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 21
low-battery warning . . . . . . . . . . . . . . . . . . . . . . . . . . 28
R
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
removable battery pack . . . . . . . . . . . . . . . . . . . . . . . . .7
removing a DIMM card . . . . . . . . . . . . . . . . . . . . . . . .35
removing a Memory Stick . . . . . . . . . . . . . . . . . . . . . .33
restoring the factory image . . . . . . . . . . . . . . . . . . . . .42
restoring your pre-installed software . . . . . . . . . . . . .42
resuming system operation . . . . . . . . . . . . . . . . . .28, 41
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
M
memory cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Memory Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 33
microphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 20
modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
S
N
SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 20, 33
navigation buttons . . . . . . . . . . . . . . . . . . . . . . . . . 6, 15
Security Application Panel
operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
O
Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 27
Setting up Security Panel . . . . . . . . . . . . . . . . . . . . . . .17
Shock Sensor Utility . . . . . . . . . . . . . . . . . . . . . . . . . . .29
shutting down the system . . . . . . . . . . . . . . . . . . . . . .27
Smart Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
solving problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
speaker/headphone volume too low . . . . . . . . . . . . . .41
OmniPass
Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
importing an OmniPass user profile . . . . . . . . . . . 78
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
verifying information . . . . . . . . . . . . . . . . . . . . . . . 74
optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
overheating, avoiding . . . . . . . . . . . . . . . . . . . . . . . . . 40
status display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
charge/DC input icon . . . . . . . . . . . . . . . . . . . . . . . .11
hard disk drive access icon . . . . . . . . . . . . . . . . . . . .12
power icon, blinking . . . . . . . . . . . . . . . . . . . . . . . . .25
power icon, system states indicated by . . . . . . .11, 25
P
page up/page down . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PC card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 20, 33
pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 10
installing a pen tether . . . . . . . . . . . . . . . . . . . . . . . 31
not responding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
replacing the tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Stylistic ST5000
care and maintenance . . . . . . . . . . . . . . . . . . . . . . .39
features . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7, 8, 9, 10
items included with . . . . . . . . . . . . . . . . . . . . . . . . . .5
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
pen tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 31
peripheral connectors . . . . . . . . . . . . . . . . . . . . . . . . . 20
Stylistic ST5000 specifications
agency approval . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
power icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 25
blinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 28
not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
power on/suspend/resume
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
power usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
82
Download from Www.Somanuals.com. All Manuals Search And Download.
I n d e x
suspend mode, determining . . . . . . . . . . . . . . . . . . . . 28
Suspend/Resume
disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Suspend/Resume button . . . . . . . . . . . . . . . . . . . . . . . 21
suspending system operation . . . . . . . . . . . . . . . . . . . 27
system interface connector . . . . . . . . . . . . . . . . . . . . . . 7
system states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Idle state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
On state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
system status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
T
Tablet Dock latch point . . . . . . . . . . . . . . . . . . . . . . . . 7
Tablet Dock port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
thermal suede . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Trusted Platform Module
enabling the security chip in BIOS . . . . . . . . . . . . 80
getting help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
turning off the system . . . . . . . . . . . . . . . . . . . . . . . . . 27
U
Universal Serial Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
USB ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 20
using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
W
Windows XP Tablet PC Edition . . . . . . . . . . . . . . . 1, 5
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ad Hoc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
connecting the WLAN . . . . . . . . . . . . . . . . . . . . . . 57
for better communications . . . . . . . . . . . . . . . . . . 55
Infrastructure Mode . . . . . . . . . . . . . . . . . . . . . . . . 55
IP address information . . . . . . . . . . . . . . . . . . . . . . 67
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
starting transmission . . . . . . . . . . . . . . . . . . . . . . . 56
stopping transmission . . . . . . . . . . . . . . . . . . . . . . 55
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
using Atheros Client Utility software . . . . . . . . . . 58
using Intel PROSet software . . . . . . . . . . . . . . . . . 57
Wireless LAN glossary . . . . . . . . . . . . . . . . . . . . . . 65
wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
before using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
wireless LAN/Bluetooth on/off switch . . . . . . . . . 7, 21
83
Download from Www.Somanuals.com. All Manuals Search And Download.
S t y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|