User Guide
XTP Power Injector
XTP PI 400
Four Port XTP Power Injector
68-2291-01 Rev. D
11 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause interference.
This interference must be corrected at the expense of the user.
ATTENTION: The Twisted Pair Extension technology works with unshielded twisted
pair (UTP) or shielded twisted pair (STP) cables; but, to ensure FCC Class A and CE
compliance, STP cables and STP Connectors are required.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
Copyright
© 2013 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks®, registered service marks(SM), and trademarks(TM) are the property of
RGB Systems, Inc. or Extron Electronics:
Registered Trademarks(®)
AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IP Intercom,
IP Link, Key Minder, LockIt, MediaLink, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System
Integrator, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTP Systems
Registered Service Mark(SM) : S3 Service Support Solutions
Trademarks(™)
AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), Auto-Image, CDRS (Class D
Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator,
DSVP (Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QS-FPC (QuickSwitch
Front Panel Controller), Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, XTRA, ZipCaddy,
ZipClip
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
WARNING: A warning indicates a situation that has the potential to result in death or
severe injury.
ATTENTION: Attention indicates a situation that may damage or destroy the
product or associated equipment.
NOTE: A note draws attention to important information.
Specifications Availability
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
XTP PI 400 Power Injector • Contents
v
Download from Www.Somanuals.com. All Manuals Search And Download.
XTP PI 400 Power Injector • Contents
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This guide contains information about the Extron XTP PI 400 Power Injector with instructions
for experienced installers on how to install, configure, and operate the equipment.
In this guide, the term “XTP PI 400” is used to refer to the XTP PI 400 Power Injector.
This section provides basic information about this guide, the XTP PI 400, and key features
of the XTP PI 400. Topics in this section include:
•
•
About the XTP PI 400
The Extron XTP PI 400 is a four port power injector that provides power for up to four
remote XTP transmitters or receivers, eliminating the need for local power supplies.
Designed specifically for the high data rates of XTP systems, signal quality is unaffected
when using the power injector. It can be installed anywhere within the XTP signal path,
providing design flexibility for remote devices with limited space. To ensure quick and
dependable installation, the 1U, half rack width enclosure can be securely mounted using
Extron rack shelves. The XTP PI 400 power injector provides integration flexibility in XTP
systems with fully populated matrix switchers.
XTP R HDMI
Receiver
XTP R HDMI
Receiver
OUTPUTS
RELAYS
POWER
12V
OVER XTP
AUDIO
AUDIO
ON
RS-232
Tx Rx
IR
L
R
1
2
RESET
OFF
CT
NK
G
T
x
R
x
+
-
+
-
HDMI
S/PDIF
XTP T HDMI
Transmitter
SIG
LINK
INPUTS
POWER
12V
AUDIO
ON
AUDIO
OVER XTP
L
R
RS-232
IR
--A MAX
RESET
PS 1210
OFF
ACTLANLINK
HDMI
LOOP-THRU
+
−
+
−
T
x
R
x
T
x
R
x
G
XTP OUT
Desktop Power
Supply
PS 1210
Desktop Power
Supply
PS 1210
Desktop Power
Supply
XTP Signal
XTP Signal
XTP Signal
100-240V x.xA
XTP PI 400
4
1
2
3
PWR
PWR
PWR
PWR
XTP
XTP PWR
XTP
XTP WR
XTP
XTP PWR
XTP
XTP PWR
50/60 Hz
XTP PI 400
XTP Power Injector
Remote Power
SIG
LINK
POWER
12V
1.0A MAX.
RESET
RS-232
XTP OUT
Tx Rx
SIG
LINK
INPUTS
POWER
12V
--A MAX
AUDIO
ON
AUDIO
OVER XTP
L
R
RS-232
IR
RESET
XTP T UWP 202
Transmitter
OFF
+
−
+
−
ACTLANLINK
HDMI
LOOP-THRU
T
x
R
x
T
x
R
x
G
XTP OUT
XTP T HDMI
Transmitter
OUTPUTS
RELAYS
AUDIO
AUDIO
ON
L
R
1
2
RESET
OFF
T
x
R
x
+
-
+
-
HDMI
S/PDIF
IN
XTP R HDMI
Receiver
Figure 1. Typical XTP PI 400 Point-to-point Application
XTP PI 400 Power Injector • Introduction
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
REMOTE
RS 232/RS422
ACT
LAN
LINK
RESET
O
U
T
I
N
P
U
T
S
P
U
T
S
100-240V --A MAX
50-60Hz
DISCONNECT POWER
CORD BEFORE
SERVICING
XTP Signal
XTP Signal
Extron
XTP CrossPoint 3200
100-240V x.xA
XTP PI 400
1
2
3
4
PWR
PWR
PWR
PWR
XTP
XTP PWR
XTP
XTP PWR
XTP
XTP PWR
PWR
50/60 Hz
XTP PI 400
XTP Power Injector
Remote Power
SIG
LINK
Remote Power
POWER
12V
RESET
1.0A MAX.
RS-232
Tx Rx
XTP OUT
SIG
LINK
XTP SR HDMI
REMOTE
OUTPUTS
AUDIO
L
POWER
12V
--A MAX
OVER XTP
RS-232
S/PDIF
HDMI AUDIO
ON
RELAYS
IR
R
1
2
RS-232
RESET
OFF
XTP IN
ACT
LINK
T
x
R
x
T
x
R
x
HDMI
+
−
+
−
Remote Power
Tx Rx
LAN
XTP T UWP 202
Transmitter
XTP SR HDMI
XTP Scaling Receiver
Remote Power
SIG
INK
INPUTS
XTP
T
USW 103
POWER
12V
--A MAX
OVER XTP
AUDIO
RS-232
IR
CONTACT
RS-232
RESET
1
2
3
XTP OUT
ACT
LINK
T
x
R
x
T
x
R
x
1
2
3
T
x
R
x
LAN
SIG
LINK
XTP SR HDMI
REMOTE
OUTPUTS
AUDIO
L
POWER
12V
--A MAX
OVER XTP
RS-232
S/PDIF
HDMI AUDIO
ON
RELAYS
IR
R
1
2
RS-232
RESET
OFF
XTP IN
CT
LINK
T
x
R
x
T
x
R
x
HDMI
+
−
+
−
Tx Rx
LAN
XTP T USW 103
XTP Transmitter
XTP SR HDMI
XTP Scaling Receiver
Figure 2. Typical XTP PI 400 Matrix Application
Features
•
Supplies power for up to four remote XTP extenders — Provides power for up to
four XTP transmitters or receivers over the XTP link, eliminating the need for local power
supplies.
•
•
Designed specifically for the high data rates of XTP systems
No impact on signal quality — Utilization of the power injector does not affect video,
audio, bidirectional RS-232 and IR, and Ethernet signal quality.
•
Real-time status LEDs for troubleshooting and monitoring — Front and rear
indicators provide status for each port that is supplying power to an XTP extender.
•
•
•
UL/c-UL Listed and CE compliant
1U, half rack width enclosure
Internal universal power supply — The 100-240 VAC, 50-60 Hz, international power
supply provides worldwide power compatibility.
XTP PI 400 Power Injector • Introduction
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and
Operation
This section contains installation procedures and operation features. Topics in this section
include:
•
•
Installation
Important Safety Instructions
This symbol, when used on the product, is intended to alert the user of important
operating and maintenance (servicing) instructions in the literature provided with the
equipment.
This symbol, when used on the product, is intended to alert the user of the presence
of uninsulated dangerous voltage within the product enclosure that may present a
risk of electric shock.
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
•
•
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
•
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
•
•
Only use attachments and accessories specified by the manufacturer.
Unplug this device apparatus during lightning storms or when unused for long periods
of time.
XTP PI 400 Power Injector • Installation and Operation
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Risk of electrical shock. To reduce the risk of fire or electric shock, do
not expose this apparatus to rain, moisture, dripping, splashing, or objects filled with
liquids.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when the power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
ATTENTION: This apparatus is a Class I product. This product must be connected to
a mains socket outlet with a protective earthing connection.
The mains plug is used as the disconnect device and must remain readily operable.
WARNING: To prevent the risk of shock, do not attempt to service this equipment
yourself because opening or removing covers may expose you to dangerous voltage
or other hazards.
ATTENTION:
• Power sources — This equipment should be operated only from the power
source indicated on the product. This equipment is intended to be used with a
main power system with a grounded (neutral) conductor. The third (grounding) pin
is a safety feature. Do not attempt to bypass or disable it.
• Power disconnection — To remove power from the equipment safely, remove
all power cords from the rear of the equipment, or the desktop power module (if
detachable), or from the power source receptacle (wall plug).
XTP PI 400 Power Injector • Installation and Operation
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel Connectors
b c
b c
b c
b c
100-240V 1.6 A
XTP PI 400
1
2
3
4
PWR
PWR
PWR
PWR
XTP
XTP PWR
XTP
XTP PWR
XTP
XTP PWR
XTP
XTP PWR
50/60 Hz
Figure 3. Rear Panel Features
ATTENTION: Do not connect these devices to a computer data or telecommunications
network.
NOTE: The XTP PI 400 does not switch XTP signals.
AC power connector — Connect the IEC power cord to the AC power connector.
a
XTP connector — Connect an Extron XTP device that is powered by a local power
source to the XTP connector on any of the four port pairs.
b
XTP PWR connector — Connect an Extron XTP device that requires power from an
external source to the XTP PWR connector. Make sure there is an XTP device plugged
into the XTP connector on the same port pair.
c
NOTE: Do not loop XTP port pairs on a single cable run to remotely power the
transmitter and receiver. Figure 5, below, shows this type of application, which is not
recommended by Extron.
POWER
12V
--A MAX
INPUTS
SIG
LINK
AUDIO
ON
AUDIO
OVER XTP
INPUTS
SIG
LINK
POWER
12V
--A MAX
L
R
RS-232
IR
AUDIO
ON
AUDIO
OVER XTP
RESET
L
R
RS-232
IR
RESET
OFF
+
−
+
−
LAN
HDMI
LOOP-THRU
T
x
R
x
G
T
x
R
x
XTOUT
OFF
ACTLANLINK
HDMI
LOOP-THRU
+
−
+
−
T
x
R
x
G
T
x
R
x
XTUT
XTP T HDMI
Transmitter
XTP T HDMI
Transmitter
CATx
CATx
Remote Power
Remote Power
100-240V x.xA
XTP PI 400
100-240V x.xA
XTP PI 400
1
2
3
4
1
2
3
4
PWR
PWR
PWR
PWR
PWR
PWR
PWR
PWR
XP
XTP PWR
XTP
XTP PWR
XTP
XTP PWR
XTP
XTP PWR
50/60 Hz
XTP
XTP PWR
XTP
XTP PWR
XTP
XTP PWR
XTP
XTP PWR
50/60 Hz
CATx
XTP PI 400
XTP PI 400
XTP Power Injector
CATx
XTP Power Injector
CATx
Remote Power
SIG
LINK
OUTPUTS
RELAYS
POWER
12V
--A MAX
OVER XTP
AUDIO
AUDIO
ON
RS-232
IR
L
R
1
2
RESET
SIG
LINK
OUTPUTS
RELAYS
OFF
POWER
12V
--A MAX
OVER XTP
ACTLANLINK
T
x
R
x
G
T
x
R
x
+
-
+
-
AUDIO
L
HDMI
S/PDIF
XTP IN
AUDIO
ON
RS-232
Tx Rx
IR
R
1
2
RESET
OFF
T
x
R
x
XTP IN
ACTLANLINK
HDMI
S/PDIF
G
+
-
+
-
XTP R HDMI
Receiver
XTP R HDMI
Receiver
CORRECT
INCORRECT
Figure 4. Correct application
• Figure 5. Incorrect application
Installation Overview
2. Connect a locally powered XTP device
to the XTP connector on one of the port
PWR
pairs.
XTP
XTP PWR
3. On the same port pair, connect an
XTP device that requires power from
an external source to the XTP PWR
connector.
To an XTP Device
To an XTP Device
that Requires an
External Power Supply
4. Repeat steps 2 and 3 for each XTP port
pair as necessary.
5. Connect AC power to the XTP PI 400.
XTP PI 400 Power Injector • Installation and Operation
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Twisted Pair Cable Recommendations
Use the following pin configurations for twisted pair cables.
Pins:
12345678
TIA/EIA-T568B
Pin Wire Color
1
2
3
4
5
6
7
8
White-orange
Orange
White-green
Blue
White-blue
Green
Insert Twisted
Pair Wires
White-brown
Brown
RJ-45
Connector
Figure 6. Twisted Pair Cable Configuration
Supported cables
The XTP PI 400 is compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair
(F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable.
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable.
• To ensure FCC Class A and CE compliance, STP cables and STP connectors are
required.
Cable recommendations
Extron recommends using the following practices to achieve full transmission distances up
to 330 feet (100 m) and reduce transmission errors:
•
Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best
performance:
•
•
•
XTP DTP 24/1000
XTP DTP 24P/1000 Plenum 1000 feet (305 m) spool
XTP DTP 24 Plug Package of 10
Non-plenum 1000 feet (305 m) spool 22-236-03
22-235-03
101-005-02
•
If you are not using XTP DTP 24 cable, at a minimum Extron recommends 24 AWG,
solid conductor, STP cable with a minimum bandwidth of 400 MHz.
•
•
Terminate cables with shielded connectors to the TIA/EIA-T568B standard.
Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use CAT 6 or 6a shielded couplers and punch down connectors.
NOTE: Using more than three patches with the XTP PI 400 yields varying maximum
cable lengths.
Number of Patches
Maximum Transmission Distance
330 ft (100 m)
1 or 2
3
280 ft (85 m)
NOTES: When using CAT 5e or CAT 6 cable in bundles or conduits:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 m where cables are straightened, aligned,
and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
XTP PI 400 Power Injector • Installation and Operation
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators
a
b
XTP POWER OUT
1
2
3
4
XTP PI 400
XTP POWER INJECTOR
Figure 7. Front Panel Features
Front panel power LED indicator — Lights to indicate the XTP PI 400 is receiving
power.
a
b
Front panel XTP Power Out LED indicators — Light when the XTP PI 400 is
providing power to XTP devices connected to the XTP PWR connectors.
NOTE: If the last connected XTP device that requires power draws more power
than the XTP PI 400 can provide, the corresponding XTP Power Out LED
indicator blinks, indicating the output cannot be powered due to the over power
draw. Disconnect the XTP device to correct the issue.
Rear panel Pwr LED indicators — Light or blink to indicate the various power states
of the XTP device connected to the corresponding XTP PWR connector (see the table
below for LED states).
c
LED State
Port Status
c
Unlit
The endpoint is not connected or cannot
be powered.
PWR
Lit
The endpoint is receiving power from the
XTP PI 400.
XTP
XTP PWR
XTP Port
Blinks five times There is a power overload fault.
Blinks nine times The power allocation is exceeded.
XTP PI 400 Power Injector • Installation and Operation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Information
Mounting
The XTP PI 400 is 1U high and one half rack wide.
ATTENTION:
• The XTP PI 400 is not suitable for use in air handling spaces or in wall cavities. The
power supply must be located within the vicinity of the Extron AV equipment in an
ordinary location with pollution degree 2, and secured to an equipment rack within
a dedicated closet, podium, or desk.
The installation must be in accordance with the applicable provisions of National
Electrical Code ANSI/NFPA 70, article 75 and Canadian Electrical Code part 1,
section 16. The power supply must not be permanently fixed to building or similar
structure.
• This device is for intra-building use only.
1. Turn off or disconnect all equipment power sources.
2. Mount the XTP PI 400 on a table, on a rack shelf, or under a desk using an optional
mounting kit.
WARNING: Risk of electrical shock. To reduce the risk of fire or electric shock, do
not expose this apparatus to rain, moisture, dripping, splashing, or objects filled with
liquids.
Tabletop Mounting
Attach the provided rubber feet to the bottom four corners of the enclosure.
Under-the-table Mounting
Use an optional Extron mounting kit to mount the XTP PI 400 under a desk or table. Follow
the instructions included with the kit.
XTP PI 400 Power Injector • Reference Information
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack Mounting
Mount the XTP PI 400 to an optional Extron rack shelf. To mount the unit on a rack shelf,
follow the instructions provided with the shelf accessories.
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
Front false
faceplate uses
2 screws.
(2) 4-40 x 3/16"
Screws
NOTE: Using screws longer
than 3/16" will damage the
unit and void the warranty.
Use 2 mounting holes on
opposite corners.
Figure 8. Half Rack Mounting
UL Guidelines for Rack Mounted Devices
The following Underwriters Laboratories (UL) guidelines pertain to the safe installation of the
XTP PI 400 in a rack.
1. Elevated operating ambient temperature — If the equipment is installed in a closed
or multi-unit rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore, install the XTP PI 400 in an
environment compatible with the maximum ambient temperature
(Tma = +122 ˚F, +50 ˚C) specified by Extron.
2. Reduced air flow — Install the equipment in a rack so that the amount of air flow
required for safe operation of the equipment is not compromised.
3. Mechanical loading — Mount the equipment in the rack so that uneven mechanical
loading does not cause a hazardous condition.
4. Circuit overloading — Connect the equipment to the supply circuit and consider the
effect that circuit overloading might have an overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when
addressing this concern.
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted
equipment. Pay particular attention to supply connections other than direct connections
to the branch circuit (for example, use of power strips).
XTP PI 400 Power Injector • Reference Information
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe and Africa:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Middle East:
Extron Asia Pte Ltd
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: 714.491.1500 or 800.633.9876
Asia: 65.6383.4400
Europe: 31.33.453.4040
Japan: 81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.
Extron Headquarters
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
Extron Korea
Extron India
+1.800.633.9876 (Inside USA/Canada Only)
+800.3987.6673
(Inside Europe Only)
+65.6383.4400
+65.6383.4664 FAX
+81.3.3511.7655
+81.3.3511.7656 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
+971.4.299.1800
+971.4.299.1880 FAX
+82.2.3444.1571
+82.2.3444.1575 FAX
1800.3070.3777
(Inside India Only)
Extron USA - West
+1.714.491.1500
Extron USA - East
+1.919.850.1000
+31.33.453.4040
+91.80.3055.3777
+1.714.491.1517 FAX
+1.919.850.1001 FAX
+31.33.453.4050 FAX
+91.80.3055.3737 FAX
Download from Www.Somanuals.com. All Manuals Search And Download.
|