Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PRECAUTIONS.............................................................................. 4
1. INTRODUCTION .......................................................................... 10
1-1. Features ..................................................................................................... 10
1-2. Package Contents ...................................................................................... 11
1-3. Controls & Connectors................................................................................ 12
2. CABLE CONNECTION................................................................ 14
2-1. Before connecting ....................................................................................... 14
2-2. Connecting up............................................................................................. 15
3. ScreenManager ........................................................................... 17
3-1. How to use the ScreenManager .................................................................. 17
3-2. ScreenManager Adjustments and Settings ............................................... 18
3-3. Useful Functions......................................................................................... 19
4. ADJUSTMENT ............................................................................ 20
4-1. Screen Adjustment ..................................................................................... 20
4-2. Displaying the low resolutions ..................................................................... 24
4-3. Color adjustment......................................................................................... 26
4-4. Power-save Setup....................................................................................... 28
5. MAKING USE OF USB (Universal Serial Bus) .......................... 29
6. CONNECTINGTWO PCs toTHE MONITOR ............................... 31
7. ATTACHING AN ARM STAND .................................................... 33
8. TROUBLESHOOTING ................................................................. 35
9. CLEANING................................................................................... 39
10. SPECIFICATIONS ....................................................................... 40
11. GLOSSARY.................................................................................. 42
12. INDEX .......................................................................................... 44
APPENDIX............................................................................................. i
TABLE OF CONTENTS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
IMPORTANT!
´ This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
´ To ensure personal safety and proper maintenance. Please read this section and the
caution statements on the monitor (refer to the figure below).
[Location of the Caution Statements]
WARNING
´ If the monitor begins to emit smoke, smells like something is
burning, or makes strange noises, disconnect all power connections
immediately and contact your dealer for advice.
Attempting to use a malfunctioning monitor can be dangerous.
´ Do not dismantle the cabinet or modify the monitor.
Dismantling the cabinet or modifying the monitor may result in electric
shock or burn.
´ Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards.
4
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
´ Keep small objects away from the monitor.
Small objects may accidentally fall through the ventilation slots into the
cabinet, leading to fire, shock, or equipment damage.
´ Keep liquids away from the monitor.
Spillage into the cabinet may result in fire, electric shock, or equipment
damage. If an object or liquid falls/spills into the cabinet, unplug the
monitor immediately. Have the monitor checked by a qualified service
engineer before using it again.
´ Place the monitor on a strong, stable surface.
A monitor placed on an inadequate surface may fall, resulting in injury or
equipment damage. If the monitor falls, disconnect the power immediately
and have the monitor checked by a qualified service engineer before using it
again. Using a monitor after it has been dropped may result in fire or
electric shock.
OK
´ Set the monitor in an appropriate location.
* Do not install in a dusty or humid environment.
* Do not place in a location where steam can have direct contact with
the screen.
* Do not place near heat generating devices or a humidifier.
´ Keep the plastic packing bags away from children and infants.
Plastic bags can be dangerous. To avoid danger of suffocation, keep the
bag away from babies and children.
• Keep power terminal covers for the optional i·Sound™ sound unit
away from children and infants.
Children and infants may accidentally swallow the covers and choke. If
swallowed, consult a doctor immediately.
Download from Www.Somanuals.com. All Manuals Search And DownloaPd.RECAUTIONS
5
WARNING
• Use the enclosed power cord. If using the power cord other than the
enclosed one, follow these guidelines.
[USA and Canada]
Use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting
the following specifications.
* Rating:
* Plug type:
* Type:
min. 125 V, 10 A
NEMA 5-15P, Parallel blade, Grounding type, 125 V, 10 A
SVT
*Length: max. 2.0 m
[Europe]
Use a proper European standard approved power cord meeting the
following specifications.
* Rating:
* Type:
min. 250 V, 10 A
*Length: max. 2.0 m
H05VV-F 3G 1 mm2
Use a plug type approved by the country where you reside. Failure to do so
may cause fire or electric shock.
´ To disconnect the power cord, grasp the plug firmly and pull.
Never tug on the cord, doing so may cause damage and couldresult in
fire or electric shock.
OK
´ The equipment must be connected to a grounded main outlet.
´ Use the correct voltage.
* The monitor is designed for use with a specific voltage only. Connection
to a different voltage may cause fire, electric shock, or other damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
* For proper connections of the power cord, be certain to plug the
power cord to the provided monitor connector and directly to a wall
outlet. Not doing so may result in fire or electric shock.
´ Handle the power cord with care.
* Do not place the cord underneath the monitor or other heavy objects.
* Do not pull on the cord.
* Do not attempt to repair a damaged cord.
If the power cord becomes damaged, stop using it. Use of a damaged
cord may result in fire or electric shock.
´ Never touch the plug and power cord if it begins to thunder.
If it begins to thunder, do not touch the plug, power cord or cable.
Touching them may result in electric shock.
6
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
´ Install the monitor securely when attaching to an arm stand.
When attaching an arm stand, please refer to the user’s manual of the arm
stand and install the monitor securely with the enclosed screws. Not doing
so may cause the monitor to come unattached, which may result in injury
or equipment damage. When the monitor is dropped, please ask your
dealer for advice. Do not continue using a damaged monitor. Using a
damaged monitor may result in fire or electric shock.
When reattaching the tilt stand, please use the same screws and tighten
them securely.
´ Do not touch a damaged LCD panel directly with bare hands.
Use protective gloves whenever handling a damaged panel. The liquid
crystal which leaks from the panel is poisonous if it enters the eyes or
mouth. If any part of the skin or body comes in direct contact with the
panel, please wash thoroughly. If some physical symptoms result, please
consult your doctor.
´ Take care when disposing of the monitor.
The backlight of the LCD panel contains mercury. Follow local
regulation or laws for safe disposal.
CAUTION
• Handle with care when carrying the monitor.
* Disconnect the power cord, signal cables and remove the optional
i·Sound™ sound unit (if applicable). Moving the monitor with the cord
attached or lifting it by the i·Sound™ sound unit is dangerous. It may
result in injury or equipment damage.
* When handling the monitor, grip the bottom of the monitor firmly with
both hands ensuring the panel faces outward before lifting.
* Handle with care to avoid scratching or damaging the panel. If the
monitor becomes damaged, disconnect the power immediately and have
the monitor checked by a qualified service engineer before using it again.
Using a monitor after it has been dropped may result in fire or electric
shock.
OK
Download from Www.Somanuals.com. All Manuals Search And DownloaPd.RECAUTIONS
7
CAUTION
´ Do not block the ventilation slots on the cabinet.
* Do not place books or any other papers on the ventilation slots.
* Do not install the monitor in a closed space.
* Do not use the monitor lengthwise or upside down.
Using the monitor in this way blocks the ventilation slots and prevents
proper airflow, leading to fire or other damage.
• Do not use the LCD monitor outdoors or inside a car.
This LCD monitor has been made specifically for indoor use as a desktop
monitor. Using it anywhere else may result in fire, electrical shock, or
other damage.
• When adjusting the viewing angle of the monitor, do not do so by
handling i·Sound™ sound unit (if applicable).
Adjusting the monitor in this way may break the monitor or cause bodily
injury.
´ At the end of the day or if you plan to leave the monitor unused for an
extended period after turning off the power switch, disconnect the
power cord from the wall socket so that no power connections are
made.
´ Do not touch the plug with wet hands.
Touching the plug with wet hands is dangerous and can cause electrical
shock.
´ Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
´ Unplug the monitor before cleaning it.
Cleaning the monitor while it is plugged into a power outlet may result in
electric shock.
´ Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl
alcohol), abrasive cleaners, or other strong solvents, as these may
cause damage to the cabinet or LCD panel.
´ Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.
8
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
Suggestions for Maximizing Comfort
´ To lessen the chance of possible injury and to increase your
comfort and productivity while you operate the monitor, we suggest
the following:
* Avoid less favorable body positioning. Sit back on the chair with
your back straight.
* Adjust the height of the chair so that the both soles touch the floor.
* Adjust the height of your chair, monitor, or keyboard so that you
can keep your wrists straight while typing.
* Set the terminal slightly below eye level.
´ Adjust brightness of the screen depending on the brightness of
your environment. Too dark or too bright of a screen can cause eye
strain.
´ Be sure to take adequate rests. A 10-minute rest period each hour
is suggested.
• Do not remove the covers to the power terminal for the optional
i·Sound™ sound unit for any reason except to attach the monitor.
LCD Panel
´ The screen may have defective pixels. These pixels may appear as
slightly light or dark area on the screen. This is due to the
characteristics of the panel itself, and not the product.
´ The backlight of the LCD panel has a fixed life span.
When the screen becomes dark or begins to flicker, please contact your
dealer.
´ Do not press on the panel or edge of the frame strongly, as this will
result in damage to the screen. There will be prints left on the
screen if the pressed image is dark or black. If pressure is
repeatedly applied to the screen, it may deteriorate or damage your
LCD panel. Leave the screen white to decrease the prints.
´ Do not scratch or press on the panel with any sharp objects, such
as a pencil or pen as this may result in damage to the panel. Do not
attempt to brush with tissues as this may scratch the LCD panel.
Download from Www.Somanuals.com. All Manuals Search And DownloaPd.RECAUTIONS
9
1. INTRODUCTION
Thank you very much for choosing an EIZO Color LCD Monitor.
1-1. Features
• Dual inputs compliant (D-Sub mini 15 pin x 2)
• 1600 x 1200 resolution
Horizontal scanning frequency of 27-94 kHz
Vertical scanning frequency of 50-85 Hz (1600 x 1200 ~75Hz)
• Auto Adjustment compliant and original “Picture Adjustment Program” software
included
• Smoothing function incorporated for the adjustment of an enlarged image
• ColorManagement function incorporated
• USB (Universal Serial Bus) hub supported
10 1. INTRODUCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
• LCD Monitor
• Signal Cable (MD-C87/C100)
• Power Cord
• Connector Cover
• 4 of 4 mm x 12 mm mounting screws • Rear Cover (attached to the monitor)
• EIZO LCD Utility Disk
• Quick Reference
• User’s Manual
• Warranty Registration Card
• Please retain the packing materials for future transference.
Download from Www.Somanuals.com. All Manuals Search And Dow1nl.oIaNd.TRODUCTION 11
1-3. Controls & Connectors
Front
(1)
(2)
(3)
(6)
(5)
(8)
(7)
(4)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
ScreenManager™
PowerTerminal Covers for the Optional peripheral
Input Signal Selection Button
Auto Adjustment Button
Enter Button
Control Buttons
Power Button
Power Indicator*1
Indicated color
Green
Power-on status
Power is on
Yellow
Power save mode
Slowly flashingYellow Power is off (Main power is on)
*1
Regarding the power indicator for the “Off Timer”, see page 19.
12 1. INTRODUCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear
(9)
(10) (11) (12)
(13) (14) (15)
(16)
(9)
Main Power Switch
(10)
(11)
(12)
(13)
(14)
(15)
(16)
4 Holes for Mounting an Arm-Stand*2
Stand (Detachable)*2
USB Downstream Ports x 4
Power Connector
Security Lock Slot*3
D-Sub mini 15 pin Input Connector x 2
USB Upstream Port x 1
*2
The LCD monitor can be used with an optional arm stand by removing the stand
(see page 33).
*3
Allows for connection of a security cable. This lock supports Kensington’s MicroSaver
security system. For further information, please consult:
Kensington Technology Group 2855 Campus Drive, San Mateo, CA 94403 USA
800-650-4242, x3348
Intl: 650-572-2700, x3348 / Fax: 650-572-9675
Download from Www.Somanuals.com. All Manuals Search And Dow1nl.oIaNd.TRODUCTION 13
2. CABLE CONNECTION
2-1. Before connecting
Before connecting your monitor to the PC, change the display screen settings (resolution
p. 43) and frequency) in accordance with the charts below.
Resolution
640 x 480
Frequency
~ 85 Hz
70 Hz
Remarks
VGA, VESA
VGA Text
720 x 400
800 x 600
~ 85 Hz
75 Hz
VESA
832 x 624
Apple Macintosh
VESA
1024 x 768
1152 x 870
1152 x 900
1280 x 960
1280 x 1024
1600 x 1200
~ 75 Hz
75 Hz
Apple Macintosh
SUN WS
~76 Hz
~ 85 Hz
~ 85 Hz
~75 Hz
Apple Macintosh
VESA
VESA
• About Plug & Play of the monitor
When your computer and display supportVESA DDC, the suitable resolution and the
refresh rate are set by just plugging your display into the computer without any
manual settings.
When your computer system supports Plug & Play, the Display Information File is
not required except for installing the Color Profile.
14 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2. Connecting the signal cable
• Be sure that the power switches of both the PC and the monitor are OFF.
1. Remove the rear cover from the monitor.
When removing the rear cover, push down the buttons while pulling.
buttons
2. Plug the signal cable into the D-Sub connector at the rear of the
monitor and the other end of the cable into the video connector on the
PC.
After connecting, secure the connection with the screw-in fasteners.
Video Output Connector
D-Sub mini 15 pin
·Standard graphics board
·Macintosh G3 (Blue & White) / G4
Power cord
Signal Cable (enclosed)
Video Output Connector
D-Sub 15 pin
Macintosh
Macintosh Adapter (Optional)
Download from Www.Somanuals.com. All Manuals Search A2nd. CDoAwBnlLoEad.CONNECTION 15
3. Plug the power cord into the power connector on the rear of the
monitor.
WARNING
• Use the enclosed power cord. If using the power cord
other than the enclosed one, follow these guidelines.
[USA and Canada]
Use a UL LISTED/CSA LABELED or CERTIFIED power cord
set meeting the following specifications:
* Rating:
* Length:
* Type:
min. 125 V, 10 A
max.2.0 m
SVT
* Plug type: NEMA 5-15P, Parallel blade,
Grounding type, 125 V, 10 A
[Europe]
Use a proper European standard approved power cord
meeting the following specifications:
* Rating:
* Length:
* Type:
min. 250 V, 10 A
max.2.0 m
H05VV-F 3G 1 mm2
Use a plug type approved by the country where you reside.
Failure to do so may cause fire or electric shock.
4. Replacing the connector cover and the rear cover.
1) Insert the rear cover into the inlets at the bottom of the stand.
2) For smooth attachment, the monitor should be tilted forward. Attach the
connector cover to the rear panel of the monitor.
1
2
5. Plug the other end of the power cord into a power outlet.
WARNING
• The equipment must be connected to a grounded main
outlet.
6. Turn on the monitor’s main power and then switch on the PC’s power.
Whenever finished, turn off the PC and the monitor.
16 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
3. ScreenManager
3-1. How to use the ScreenManager
As shown on the display, the ScreenManager is used to adjust the LCD monitor.
ScreenManager consists of main menus and sub menus. Adjustments are made using the
Enter and Control buttons (up, down, right and left) located on the front panel.
Auto Adjustment Button
Enter Button
Control Buttons
1. Entering the ScreenManager
Push the Enter button once to display the main menu of the ScreenManager.
[ Main Menu ]
2. Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control buttons and push the Enter
button. The sub menu appears.
(2) Use the Control buttons to select the desired setting icon and push the Enter
button. The setting menu appears.
(3) Use the Control buttons to make all required adjustments and push the Enter
button to save the settings.
3. Exiting the ScreenManager
(1) To return to the main menu, select the “Return” icon or push the down button
twice, followed by the Enter button.
(2) To exit the ScreenManager, select “Exit” icon and push the Enter button.
3. ScreenManager 17
Download from Www.Somanuals.com. All Manuals Search And Download.
• Double clicking the Enter button at any time also exits the ScreenManager menu.
• Leaving the ScreenManager idle for 45 seconds or more will turn the adjustment off
automatically, without saving the adjustments.
3-2. ScreenManager Adjustments and Settings
The following table shows all the ScreenManager’s adjustment and setting menus.
Main menu
Screen
Sub menu
Clock
Reference
Phase
Position
Resolution
Smoothing
Contrast
Brightness
ColorManagement RangeAdjustment
Standard mode
·Temperature
Custom mode
·Temperature
·Saturation
·Hue
4. ADJUSTMENT(p.20)
·Gain
·Save
PowerManager
Others
VESA DPMS
EIZO MPMS
ScreenSize
Border Intensity
Input Priority
OffTimer
Select the priority input signal. (p.32)
Set the monitor’s off timer to on or off. (p.19)
Set the Monitor’s beeper to on or off. (p.41)
Adjust the ScreenManager’s menu position.
Return to the factory default settings. (p.41)
Review the current ScreenManager’s settings.
Beep
Menu Position
Reset
Information
Language
Information
English, German,
French
Select the ScreenManager’s language.
Spanish, Italian,
Swedish and
Japanese
18 3. ScreenManager
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
• Auto adjustment button adjustments and settings in the
ScreenManager.
Unlocked function
• Adjustment of contrast and brightness by the control buttons.
• Input signal selection button
• To lock
Press on the Auto adjustment button while switching on the monitor’s power button
on the front panel.
• To unlock
Switch off the monitor’s power button on the front panel, then hold down the Auto
adjustment button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state after a
predetermined amount of time has lapsed. This function was created to reduce
afterimagep.42) characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.
[Procedure]
(1) Select “Off Timer” in the ScreenManager “Others” menu.
(2) Select “Enable” and press the right and left buttons to adjust the “On Period”
(1 to 23 hours).
[Off timer system]
PC
Monitor
LED
On Period (1H~23H)
Operation
Green
Advance Notice*1
(with Beeps)
Last 15 min. in "On period"
"On period" expired
Green Flashing
"Power Off" Mode
Flashing yellow slowly
*1Advance notice (LED flashing green) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode,
press the power button during the advance notice period. The monitor will continue to
operate for an additional 90 minutes.
Press the power button to return to a normal screen.
• The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor’s power is switched off.
3. ScreenManager 19
Download from Www.Somanuals.com. All Manuals Search And Download.
4. ADJUSTMENT
4-1. Screen Adjustment
Screen adjustments for the LCD monitor should be used in suppressing screen flickering
and also for adjusting the screen to its proper position. There is only one correct position
for each display mode. It is also recommended to use the ScreenManager function when
first installing the display or whenever changing the system. For convenience, an easy
set-up Program installed on the utility disk to assist in the set-up procedure is provided.
Adjustment Procedure
• Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments.
1. Push the Auto adjustment button on the front panel.
The message “Your setting will be lost, if you press again now.” appears and
remains on the screen for 5 seconds. While the message is on the screen, push the
Auto adjustment button again to automatically adjust the clock, phase, screen
position and resolution. If you do not wish to do adjust the screen, do not push the
Auto adjustment button again.
If the appropriate screen can not be made by using the Auto adjustment button,
adjust the screen through the following procedures.
2. Install the “Screen adjustment program”.
Having read the “readme.txt” file, install and run the “Screen adjustment program”
in the enclosed EIZO LCD utility disk.
Step by step adjustment is provided by the wizard guide.
• If the user’s operating system has no utility disk (e.g. OS/2), we recommend
setting the desktop pattern to that as shown in the diagram below.
Every-other-dot
pattern
20 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Adjust by using “Screen” menu in the ScreenManager.
(1) Vertical bars appear on the screen.
Use the “Clock”p.42) adjustment
Select the “Clock” and eliminate the vertical bars by using the right and left of
the control buttons. Do not continuously press the control buttons, as the
adjustment value will change quickly and make it difficult to locate the most
suitable adjustment point.
If the horizontal flickering, blur or bars appear, proceed to “Phase” adjustment
as follows.
• When adjusting the “Clock,” the horizontal screen size will also change.
(2) Horizontal flickering, blurring or bars appear on the screen.
Use the “Phase”p.42) adjustment
Select the “Phase” and eliminate the horizontal flickering, blurring or bars by
using the right and left buttons.
• Horizontal bars may not completely disappear from the screen depending on the
PC.
4. ADJUSTMENT 21
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) The screen position is incorrect.
Use the “Position” adjustment
The correct displayed position of LCD monitor is decided because the number
and the position of the pixels are fixed. The “Position” adjustment moves the
image to the correct position.
Select “Position” and adjust the position of the upper left corner of the image
by using the up, down, right and left buttons in order to align the screen.
If vertical bars of distortion appear after finishing the “Position” adjustment,
return to “Clock” adjustment and repeat the previously explained adjustment
procedure (“Clock”à “Phase” à “Position”).
(4) Screen image is smaller or larger than the actual screen images.
Use the “Resolution” adjustment
Adjustment is needed when the input signal resolution and the resolution now
being displayed is different.
Select “Resolution” and confirm if the resolution now being displayed is the
same as the input resolution. If it is not, adjust the vertical resolution using
the up and down button and adjust the horizontal resolution using the right
and left buttons.
Smaller than the actual screen images.
Adjusted to actual screen size.
Larger than the actual screen images.
22 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Set the Output signal range (Dynamic Range) of the signal.
Perform the “Range Adjustment”p.43)
This controls the level of output signal range to display the whole color gradation
(256 colors). Select the “Range Adjustment”in the color menu.
[Auto]
Push the Auto adjustment button on the front panel while displaying the “Range
adjustment” menu to automatically adjust the range. The screen blanks for a
moment, and adjusts the color range to display the whole color gradation of the
current output signal.
5. Set the Contrast of the screen.
Adjust the “Contrast”
This controls the brightness for the each color (red, blue and green) at a same time.
Select “Contrast/Brightness” in the screen menu and adjust by using the right and
left buttons.
• Percentage over the 100 % may cause undisplayable color tone.
6. Set the Brightness of the screen.
Adjust the “Brightness”
This controls the brightness for the entire screen. The brightness of the entire screen
is controlled by changing the brightness if the backlight.
Select “Contrast/Brightness” in the screen menu and adjust by using the up and
down buttons.
• Directly pressing the control buttons also adjusts the contrast and brightness. Press
the “Enter” button to save and exit the settings after the adjustment.
4. ADJUSTMENT 23
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2. Displaying a low resolutions
The lower resolutions are enlarged to full screen automatically. Using the “Screen Size”
function in the “Others” menu enables to change the screen size.
1. Change the screen size when displaying a low resolution.
Select “Screen Size”
Select the “Screen Size” in the others menu and select the screen size by using the
up and down buttons.
• Full
Displays the picture on the screen in full, irrespective of the
picture’s resolution. Since the vertical resolution and the
horizontal resolution are enlarged at different rates, some
images may appear distorted.
• Enlarged
• Normal
Displays the picture on the screen in full, irrespective of the
picture’s resolution. Since the vertical resolution and the
horizontal resolution are enlarged at same rates, some
horizontal or vertical image may disappear.
Displays the picture at the actual Screen resolution.
ex.) displaying 1280 x 1024
Enlarged
Normal
Full (default setting)
1500 x 1200
1600 x 1200
1280 x 1024
24 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Smooth the blurred texts of the enlarged screen.
Adjust the “ Smoothing”
Some lines of the texts or pictures may appear with the different size in the
“Enlarged” mode or “Full Screen” mode.
Select “Smoothing” in the screen menu and adjust by using the right and left
buttons.
• “Smoothing” is disabled when the screen is displayed in the following resolution.
* 1600 x 1200
* The image size is doubled both in horizontally and vertically (i.e. 1600 x 1200
enlarged from 800 x600) to provide clear focus which does not require this
function.
3. Set the brightness of the black area surrounding the displayed image.
Set the “Border Intensity”
In the “Enlarged” mode or “Full Screen” mode, the outer area (border) is usually
black.
Select “Border Intensity” in the others menu and adjust by using the right and left
buttons.
Border
4. ADJUSTMENT 25
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3. Color Adjustment
The “ColorManagement”menu in the ScreenManager enables to change the color of the
screen.
Before the Color adjustment
• Allow the LCD monitor to stabilize for at least 20 minutes before making color
adjustments.
• After finishing each adjustment in the custom mode, select “Save” icon to resister the
adjustment. Otherwise, the adjustment will be lost.
• The values shown in percentages represent the current level within the specific
adjustment only. They are available only as a reference tool. (To create a uniform
white or black screen, the percentages for each will probably not be the same.)
• Perform the “Range Adjustment”before making the color adjustments. The gradation
pattern like below is recommended at the “Range Adjustment”.
1. To change the color tone of the white.
Set the “Temperature”p.42)
The temperature can be set from 4,000 K to 10,000 K , in 500 K increments (except
9,300 K). The default setting is “OFF”.
To resister the adjustment in the custom mode, select the “Save” icon and then push
the enter button.
• The values shown in the Kelvin are available only as a reference tool.
• Setting the temperature under 4,000 K or over 10,000 K invalidates the color
temperature setting. (The color temperature’s setting turns “OFF”.)
• Adjusting the “Gain” (p. 27) invalidates the color temperature setting. (The
color temperature’s setting turns “OFF”.)
26 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
2. To change the saturation.
Adjust the “Saturation”
The saturation can be selected from -16 ~ 16. Setting the minimum level (-16) turns
the image to the monochrome.
To register the adjustment, select the “Save” icon and then push the enter button.
• The “Saturation” adjustment may cause undisplayable color tone.
3. To change the flesh color, etc.
Adjust the “Hue”
The “Hue” can be selected from -20 ~ 20.
To register the adjustment, select the “Save” icon and then push the enter button.
• The “Hue” adjustment may cause undisplayable color tone.
4. To adjust each color (red, green and blue).
Adjust the “Gain”p.42)
By adjusting the red, green and blue color tones for each mode, custom colors can
be defined.
The 100 % indicates unadjusted condition.
Display a white or gray background image and adjust the gain.
To register the adjustment, select the “Save” icon and then push the Enter button.
• Adjusting the “Gain” invalidates the color temperature setting. (The color
temperature’s setting turns “OFF”. )
• The values shown in the percentage are available only as a reference tool.
4. ADJUSTMENT 27
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4. Power-save Setup
This monitor complies with the VESA DPMSp.43) standard and adopts a power saving
method, EIZO MPMS p.42), which works with a blank screen (totally black screen) like
“Blank Screen” ScreenSaver software.
1. To use the PC’s power saving system (VESA DPMS ).
[Procedure]
(1)Set the PC’s power saving settings.
(2)Select “VESA DPMS” in the “PowerManager” menu.
[Power saving system]
PC
ON
Monitor
LED
Power consumption
53 W
Operation
Green
STAND-BY
SUSPEND Power saving
OFF
Power saving mode
Yellow
Less than 3 W
Operate the mouse or keyboard to return to a normal screen.
2. To set the power save with ScreenSaver (EIZO MPMS) software.
[Procedure]
(1)Set the PC’s appropriate ScreenSaver settings or blank the screen (totally black
screen).
(2)Select “EIZO MPMS” from the “PowerManager” menu.
[Power saving system]
PC
ON
Monitor
LED
Power consumption
53 W
Operation
Green
Blank the screen
(ScreenSaver or
Power saving
Yellow
Less than 3 W
Macintosh Energy Saver)
Operate the mouse or keyboard to return to a normal screen.
• EIZO MPMS should be used with Macintosh “EnergySaver”.
• Do your part to conserve energy, turn off the monitor when you are finished using it.
Disconnecting the monitor from the power supply is recommended to save energy
completely.
• Even if the monitor is in a power saving mode, USB compliant devices function when
they are connected to the monitor’s USB (both the upstream and the downstream
ports). Therefore, power consumption of the monitor will change according to the
connected devices even if the monitor is in a power saving mode.
28 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
5. MAKING USE OF USB
(Universal Serial Bus)
This monitor provides a hub which supports the USB standard. When connecting to a
USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.
Required system environment
• PC equipped with USB ports or another USB hub connected to the USB compliant PC
• Windows 98/2000 // Mac OS 8.5.1 or later
• USB cable / MD-C93 (Optional)
• The USB hub function may not work properly depending on the PC, OS or
peripherals. Please consult the manufacturer of each device about the USB support.
• When the monitor is not on, the peripherals connected to the downstream ports will
not operate.
• Even if the monitor is in a power saving mode, the devices connected to the
monitor’s USB ports (both the upstream and the downstream) will function.
Connecting to the USB HUB
• Do not connect the downstream port of the monitor to any peripherals until finishing
the USB function.
• The followings are procedures for theWindows 98 Second Edition/2000 and Mac OS.
1.
2.
Connect the monitor to the PC with the signal cable (See page 15) first, then turn on
the PC.
Connect the upstream port of the monitor to the downstream port of the USB
compliant PC or another hub by using the USB cable .
Upstream Ports
Upstream port:
Connect the USB
compliant PC or another
hub using the USB cable.
To Downstream Ports
of the PC or Another
Hub
After connecting the USB cable, the USB function can be set up automatically.
5. MAKING USE OF USB (Universal Serial Bus) 29
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
After setting up, the monitor’s USB hub is available for connecting USB compliant
peripherals to the downstream ports of the monitor.
Example of connection:
Scanner
Digital
Camera
Printer
USB
Cable
Monitor
PC
Keyboard
Mouse
Downstream
Downstream ports:
Connect the cables from
USB compliant peripherals
such as a mouse, keyboard,
etc.
30 5. MAKING USE OF USB (Universal Serial Bus)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. CONNECTINGTWO PCs to
THE MONITOR
Two PCs can be connected to the monitor through the Signal 1 and the Signal 2 on the
back of the monitor.
• Connecting example
Power cord
Signal Cable
Signal cable MD-C87/
(enclosed)
MD-C100 (optional)
Video Output Connector
Video Output Connector
D-Sub mini 15 pin
D-Sub mini 15 pin
Macintosh G3
(Blue & White) / G4
Standard graphics board
Selecting the active input
The Input signal selection button on the front panel can be used to select either
Signal 1 or Signal 2 as the active input at any time. Every time the button is
pressed, the input changes.
Input Signal
Selection Button
6.CONNECTINGTWO PCsTOTHE MONITOR 31
Download from Www.Somanuals.com. All Manuals Search And Download.
The priority input signal
This function is used to select which PC will have priority to control the monitor
when utilizing two PCs. The monitor constantly checks the input signals and
switches automatically in accordance with the “Input Priority” setting (see table
below).
Once a priority is set, whenever a change of signal is detected at the selected input, the
monitor will switch the input to that signal.
In the case of only one signal being present at either input, the monitor automatically
detects and displays that signal.
Priority setting
Signal 1
Performance
If signals from both inputs are present, the monitor gives preference
to Signal 1 in the following cases.
• When the power of the monitor is turned ON.
• When the signal input to Signal 1 is changed even if active input
was Signal 2.
Signal 2
Manual
If signals from both inputs are present, the monitor gives preference
to Signal 2 in the following cases.
• When the power of the monitor is turned ON.
• When the signal input to Signal 2 is changed even if active input
was Signal 1.
The monitor will not detect signals automatically in this mode.
Select the active input by pressing the input signal selection button
on the monitor’s front panel.
• Regarding the power saving mode
When the Signal 1 or Signal 2 is selected, the power saving mode of the monitor
activates only if both PCs are in power saving mode.
32 6.CONNECTINGTWO PCsTOTHE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
7. ATTACHING AN ARM STAND
The LCD monitor can be used with an arm stand by removing the tilt stand and
attaching the arm stand to the LCD monitor.
NOTE
´ Use an arm stand that satisfies the followings.
• When using the LCD monitor with an arm stand,the
arm stand must be VESA approved :
M4 x 12 mm x 4
* Use an arm stand with a 100 mm x 100 mm hole
spacing on the arm mounting pad.
* Use an arm stand that is able to support an
object weighing 13.5 kg.
100 mm
100 mm
´ TÜV/GS approved arm stand.
´ Use an arm stand with sufficient stability
(mechanical firmness) to support the weight of the
monitor.
´ Use an arm stand remaining that position where it is
manually moved.
´ Use an arm stand with the ability to tilt the monitor
forward and backward.
´ Use an arm stand less than or equal to 500 mm in
relation to the desk surface when the arm stand is in
its lowest position.
500 mm or
less
(Example)
´ Please connect cables after attaching an arm stand.
Setup Procedure
1.
Lay the LCD monitor down as shown below. Do not scratch the panel.
Soft Cloth or
Cushion
7.ATTACHING AN ARN STAND 33
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Remove the stand by loosening the screws.(4 pcs of 4 x 10 S-Type Ni/Fe)
Attach an arm stand to the LCD monitor securely.
WARNING
´ Install the monitor securely when attaching to an arm
stand.
When attaching an arm stand, please refer to the user’s
manual of the arm stand and install the monitor securely
with the enclosed screws. Not doing so may cause the
monitor to come unattached, which may result in injury or
equipment damage. When the monitor is dropped, please
ask your dealer for advice. Do not continue using a
damaged monitor. Using a damaged monitor may result in
fire or electric shock.
When reattaching the tilt stand, please use the same screws
(4 x 10 S-Type Ni/Fe) and tighten them securely.
M4 Mounting Screws
(enclosed):M4 x 12 (mm)
Arm-stand
34 7.ATTACHINGDAoNwnAloaRdNfroSmTWAwNwD.Somanuals.com. All Manuals Search And Download.
8. TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO
dealer.
No picture problems: See No.1 ~ No.2
Imaging problems: SeeNo.3 ~ No.12
USB problems: See No.18 ~ No.19
Other problems: See No.13 ~ No.17
Problems
1. No picture
Points to check with possible solutions
Check that the power cord is correctly connected.
If the problem persists, turn off the monitor power for a
few minutes, then turn it back on and try again.
• Indicator status: Off
• Indicator status: Green
• Indicator status: Yellow
Check the “Contrast and Brightness” settings.
Minimum settings will cause screen to be blank.
Try pressing a key on the keyboard, or clicking the mouse.
(p.28)
• Indicator status: Slowly
Try pressing the power button.
flashing Yellow
2. Following messages
appear.
These messages appear when the signal is not inputted
correctly, even if the monitor functions properly.
Error messages shown below will remain on the screen for
40 seconds.
When the image is displayed correctly after a short time,
there is no problem with the monitor.
(Some PCs do not output the signal soon after powering
on.)
Check that the PC is turned ON.
Check that the signal cable is properly connected to the PC
or graphics board.
Switch the signal input by pressing the input signal
selection button on the front control panel.
•Whenever an error signal
message appears, the
signal frequency will be
displayed in red.
Use the graphics board’s utility software to change the
frequency setting. (Refer to the manual of the graphics
board.)
(Example)
8.TROUBLESHOOTING 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems
Points to check with possible solutions
3. Display position is
incorrect.
Adjust the image position using the “Position”.
(p.22)
If the problem persists, use the graphics board’s utility
software to change the display position if available.
4. Screen image is smaller or
larger than the actual
screen images.
Adjust the resolution using the “Resolution”. (p.22)
Decrease the vertical bars using the “Clock”. (p.21)
5. Vertical bars of distortion
appear.
Decrease the horizontal bars using the “Phase’. (p.21)
Adjust the blurred lines using “Smoothing”. (p.25)
6. Horizontal bars of
distortion appear.
7. Letters and lines appear
blurred.
This happens when both composite (X-OR) input signal
and separate vertical synchronizing signal are input.
Please select one of the two.
8. Distortion appears like the
figure below.
Adjust the “contrast and brightness”.
9. The screen is too bright or
too dark.
(The backlight of the LCD monitor has a fixed life span.
When the screen becomes dark or begins to flicker,
please contact your dealer.)
10. Afterimages appear.
When the screen image is changed after displaying the
same image for a long period, an afterimage may appear.
Use the “Off Timer” function and avoid keeping the screen
on all the time. (p.19)
36 8.TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems
Points to check with possible solutions
11. The screen has defective
pixels (e.g. slightly light
or dark).
This is due to the characteristics of the panel itself, and not
the LCD product.
12. Fingerprints remain on
the screen.
Leaving the screen white may solve the problem.
13. The “Smoothing” can not
“Smoothing” is disabled when the screen is displayed in the
following resolution.
be selected.
• 1600 x 1200
The image size is doubled both in horizontally and
vertically (i.e. 1600 x1200 enlarged from 800 x600) to
provide clear focus which does not require this function.
14. The utility disk is unable
to be opened (for
Some PCs without PC-Exchange do not allow the utility
disk to be opened. Please set the desktop pattern to every-
other-dot before adjustment. (p.20)
Macintosh only).
The adjustment lock is probably on. To unlock: switch the
LCD monitor off. Then, while pressing the Auto
adjustment button switch, the power on. (p.19)
15. • The Enter button does
not operate.
• The Auto adjustment
button does not operate.
16. The Auto adjustment
button does not work
properly.
The Auto sizing function is intended for use on the
Macintosh and on AT-compatible PC running Windows.
It may not work properly in either of the following cases.
When running an AT-compatible PC on MS-DOS (Not
windows).
The background color for the “wall paper” or “desktop”
pattern is set to black.
Some signals from a graphics board may not function
properly.
8.TROUBLESHOOTING 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems
Points to check with possible solutions
17. Frequency does not
change after installing
“Monitor information
file” in the attached
utility disk on Windows
95/98/2000.
Use the graphics board’s utility software to change the
input signal frequency.
Check that the USB cable is correctly connected.
Check that the PC and OS are USB compliant.
(For verification of USB support, consult the manufacturer
of each system.)
18. USB function cannot be
setup.
Check the PC’s BIOS setting for USB.
(For details, refer to the manual of the PC.)
Check that the USB cable is correctly connected.
Check the downstream ports by connecting the
peripherals to other downstream ports.
If the problem is solved by doing this, contact an EIZO
dealer.
19. PC is hung up. / The
peripherals connected to
the downstream ports do
not operate.
Try executing the following method.
-Restarting the PC
-Connecting the PC and peripherals directly
If the problem is solved by doing this, contact an EIZO
dealer.
The power button of the APPLE keyboard does not
operate if it is connected to the EIZO USB Hub. Please
connect the keyboard directly with the PC. Refer to the
instruction of the PC for details.
38 8.TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
9. CLEANING
Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.
WARNING
´ Keep liquids away from the monitor.
Spillage into the cabinet may result in fire, electric shock, or
equipment damage.
If an object or liquid falls/spills into the cabinet, unplug the
monitor immediately. Have the monitor checked by a qualified
service engineer before using it again.
CAUTION
´ Unplug the monitor before cleaning it.
Cleaning the monitor while it is plugged into a power outlet may
result in electric shock.
´ Never use thinner, benzene, alcohol (ethanol, methanol, or
isopropyl alcohol), abrasive cleaners, or other strong
solvents, as these may cause damage to the cabinet or LCD
panel.
´ Periodically clean the area around the plug.
Buildup of dust water, or oil on the plug may result in fire.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly onto the cabinet.
LCD Panel
The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.
If necessary, stubborn stains can be removed by moistening part of a cloth with water to
enhance its cleaning power.
9. CLEANING 39
Download from Www.Somanuals.com. All Manuals Search And Download.
10.SPECIFICATIONS
LCD Panel
50 cm (19.6 inch), TFT color LCD panel with Anti-
Glare Hard Coating
Viewing Angle: Horizontal: 150º, Vertical: 150º
(at Contrast Ratio > 5)
Dot Pitch
0.249 mm
Scan Frequency
Horizontal:
Vertical:
27 kHz - 94 kHz (Automatic)
50 Hz-85 Hz (Automatic)
(1600 x 1200: up to 75 Hz)
Resolution
1600 dots x 1200 lines
Dot Clock (Max.)
Display Colors
Display Area
202.5 MHz
16 milion colors (max)
398 mm (H) x 299 mm (V) (15.7” (H) x 11.8” (V))
(Viewable image size: 497 mm (19.6”))
100-120/220-240 VAC 10%, 50/60 Hz, 0.8 A/0.4 A
Normal: 53 W
Power Supply
Power Consumption
Max: 75 W (With EIZO optional speaker & USB
attached)
Power Saving Mode: Less than 3 W (when the USB
hub is not connected)
Input Connector
Input Signal
D-Sub mini 15 pin x 2
Sync: a) Separate, TTL, Positive/Negative
b) Composite, TTL, Positive/Negative
c) Sync on Green, 0.3 Vp-p, Negative
Video: 0.7 Vp-p/75 Ω, Positive
28 (preset 27)
Signal registration
Plug & Play
VESA DDC 2B
Dimensions
472 mm (W) x 477.9 mm (H) x 218 mm (D)
(18.6” (W) x 18.9” (H) x 8.6” (D))
472 mm (W) x 399 mm (H) x 93.5 mm (D)
(18.6” (W) x 15.7” (H) x 3.7”(D))
9.5 kg (20.9 lbs.)
Dimensions (without stand)
Weight
Weight (without stand)
Temperature
7.7 kg (17.0 lbs.)
operating:
storage:
0°C to 35°C (32°F to 95°F)
-20°C to 60°C (-4°F to 140°F)
Humidity
30% to 80% R.H. Non-condensing
USB specification
USB standard
Communication speed
Downstream power supply
USB ports
Rev. 1.1 complied self-powered hub
12 Mbps (full), 1.5 Mbps (low)
500 mA for each (Max.)
Upstream port x 1, Downstream port x 4
*Applicable to gray (standard) color version only.
40 10.SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
Default setting
Default setting are as follows:
•Contrast
100 %
•Brightness
•Smoothing
•Color
100 %
3
Standard mode/Off (Temperature)
•PowerManager
•Screen Size
•Input Priority
•Off Timer
•Beep
VESA DPMS
Full Screen
Signal 1
Disable
On
•Language
English
Beeper settings
Short beep
· ScreenManager item selected.
· ScreenManager parameter adjusted to minimum or
maximum limit.
· Input signal selection button pressed.
· Auto Adjustment button pressed.
· ScreenManager data-save executed.
· Monitor not connected correctly.
· PC turned off.
Long beep
4 short beeps
· Monitor received unsupported signal frequency.
2 short beeps every15 sec. · Monitor is in the advance notice mode of the Off
Timer. The power will be off within fifteen minutes.
10.SPECIFICATIONS 41
Download from Www.Somanuals.com. All Manuals Search And Download.
11.GLOSSARY
Afterimage
The Afterimage is particular to LCD monitors when the monitor screen is left on for
a long period without use. The “Afterimage” can be removed gradually by
changing the displayed image.
Clock
With the analog input signal display, the analog signal is converted to a digital
signal by the LCD circuitry. To convert the signal correctly, the LCD monitor needs
to produce the same number clock pulse as the dot clock of the graphics system.
When the clock pulse is not correctly set, some vertical bars of distortion are
displayed on the screen.
ColorTemperature (Temperature)
Color Temperature is a method to measure the white color tone, generally indicated
in degrees Kelvin. At high temperatures the white tone appears somewhat blue,
while at lower temperatures it appears somewhat red. Computer monitors
generally give best perfoemance at high temerature settings.
5000K: Slightly reddish white.
6500K: Warm-white tone, similar to white papaer or daylight.
9,300K: Slightly bluish white.
EIZO MPMS
EIZO MPMS, “EIZO Monitor PowerManager Signaling”, also enables power
saving on the monitor side. EIZO MPMS recognizes video signals from the PC
when the PC is in a power saving mode, and reduces energy consumption of the
monitor.
Gain Adjustment
Adjusts each color parameter for red, green and blue. The color of the LCD
monitor is displayed through the color filter of the LCD panel. Red, green and blue
are the three primary colors. The colors on the monitor are displayed by
combining these three colors. The color tone can change by adjusting the
illumination amount passed through each color’s filter.
Phase
The phase adjustment decides the sampling timing point for converting the analog
input signal to a digital signal. Adjusting the phase after the clock adjustment will
produce a clear screen.
42 11.GLOSSARY
Download from Www.Somanuals.com. All Manuals Search And Download.
Range Adjustment
The Range Adjustment controls the level of output signal range to display the whole
color gradation
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated
to form the screen image.
The EIZO L771 monitor panel consists of 1600 horizontal pixels and 1200 vertical
pixels. At a resolution of 1600 X1200, all pixels are used and the image is
displayed as a full screen. At the lower display modes of 640 x 480 or 800 x 600,
the images are displayed in the center of the screen using a smaller portion of the
pixels. (“Normal” setting in the “Screen Size” menu.)
VESA DPMS
The acronym VESA stands for “Video Electronics Standards
Association,” and DPMS stands for “Display Power Management Signaling.”
DPMS is a communication standard that PCs and graphics boards use to implement
power savings on the monitor side.
11.GLOSSARY 43
Download from Www.Somanuals.com. All Manuals Search And Download.
12.INDEX
A
M
ADJUSTMENT --------------------------- 20
Adjustment Lock ------------------------- 19
Afterimage ----------------------------- 19,42
ATTACHING AN ARM STAND -------- 33
MAKING USE OF USB
(Universal Serial Bus)--- 29
Menu Position----------------------------- 18
O
P
B
Off timer------------------------------- 18, 19
Others -------------------------------------- 18
Beep ---------------------------------------- 18
Beeper setting ---------------------------- 41
Before connecting ----------------------- 14
Border Intensity --------------------- 18, 25
Brightness ---------------------------- 18, 23
Package Contents ----------------------- 11
Phase ----------------------------- 18, 21, 42
Pin Assignment --------------------------- iv
Position -------------------------------- 18, 22
Power consumption ----------------- 28, 40
Power Indicator --------------------------- 12
PowerManager ----------------------- 18, 28
Power-save Setup ----------------------- 28
PRECAUTIONS --------------------------- 4
PresetTiming Chart ----------------------- i
C
CABLE CONNECTION ----------------- 14
CLEANING -------------------------------- 39
Clock------------------------------ 18, 21, 42
Color adjustment ------------------------- 26
ColorManagement ------------------ 18, 26
CONNECTINGTWO PCs to
THE MONITOR -- 31
R
S
Contrast ------------------------------- 18, 23
Controls & Connectors------------------ 12
Custom Mode ----------------------------- 18
Range Adjustment ------------------ 18, 23
Reset --------------------------------------- 18
Resolution ------------- 14, 18, 22, 40, 43
D
Default setting ---------------------------- 41
Dimensions --------------------------------- iv
Displaying the low resolutions -------- 24
Saturation ----------------------------- 18, 27
Save ------------------------------ 17, 18, 26
Screen --------------------------------- 18, 21
Screen Adjustment ---------------------- 20
Screen Size -------------------------- 18, 24
ScreenManager--------------------------- 17
ScreenManager Adjustments
E
EIZO LCD utility disk -------------- 11, 20
EIZO MPMS -------------------- 19, 28, 42
and Settings----- 18
G
Security Lock Slot ----------------------- 13
Smoothing ---------------------------- 18, 25
SPECIFICATIONS ----------------------- 40
Gain ------------------------------- 18, 27, 42
GLOSSARY ------------------------------- 42
H
T
How to use the ScreenManager ------ 17
Hue ------------------------------------- 18, 27
Temperature ---------------------- 18, 27,42
TROUBLE SHOOTING ----------------- 35
I
U
V
Information -------------------------------- 18
Input Priority ------------------------- 18, 32
USB ------------------------------- 29, 32, 40
VESA DPMS-------------------- 18, 28, 43
L
Language ---------------------------------- 18
44 12. INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX / ANHANG / ANNEXE
PresetTiming Chart for Analog input
Timing-Übersichten für Analog Eingang
Synchronisation des Signaux pour Analog numerique
Based on the signal diagram shown below, 27 factory presets have been registered in
the monitor's microprocessor.
Der integrierte Mikroprozessor des Monitors unterstützt 27 werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
27 signaux ont été enregistrés en usine dans le microprocesseur du moniteur,
conformément au diagramme de synchronisation ci-dessous.
A
B
Front Porch
Sync Period
Vordere Schwarzschulter
Synchronimpuls
Front avant
Délai de
synchronisation
C
D
E
F
Back Porch
Blanking Period
Display period
Total cycle
Hintere Schwarzschulter
Austastzeit
Front arrière
Délai de clignotement
Délai d'affichage
Cycle total
Display-Zeit
Kompletter Zyklus
Sync-Signalpegel
H
Sync signal level
Niveau du signal de
synchronisation
V
Video signal level
Video-Signalpegel
Niveau du signal vidéo
APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode
Dot Clock
MHz
Frequencies
A: Front Porch
B: Sync Period
H
V
H
V
H
V
kHz
Hz
µs/
Dot
ms/
Line
µs/
Dot
ms/
Line
VGA
0.636/
16
0.318/
10
3.813/
96
0.054/
2
640 x 480 25.175
31.468
31.468
35.00
49.73
68.68
74.763
37.86
37.5
59.941
70.087
66.67
74.55
75.06
74.763
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.061
60.00
70.07
75.03
85.0
VGA
0.636/
18
0.381/
12
3.813/
108
0.064/
2
720 x 400 28.322
Macintosh
640 x 480
2.116/
64
0.086/
3
2.116/
64
0.086/
3
30.24
57.28
Macintosh
832 x 624
0.559/
32
0.020/
1
1.117/
64
0.060/
3
Macintosh
1152 x 870 100.0
0.320/
32
0.044/
3
1.280/
128
0.044/
3
Macintosh
1280 x 960 126.2
0.190/
24
0.013 /
1
1.204/
3
0.040/
3
VESA
640 x 480
0.508/
24
0.026/
9
1.270/
40
0.079/
3
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.25
VESA
640 x 480
0.508/
16
0.027/
1
2.032/
67
0.080/
3
VESA
640 x 480
1.556/
56
0.023/
1
1.556/
56
0.069/
3
43.27
35.16
37.88
48.08
46.88
53.674
48.36
56.48
60.02
68.68
63.98
79.97
91.14
75.00
81.25
87.50
93.75
61.974
71.858
VESA
800 x 600
0.667/
24
0.028/
1
2.000/
72
0.057/
2
VESA
800 x 600
1.000/
40
0.026/
1
3.200/
128
0.106/
4
VESA
800 x 600
1.120/
56
0.770/
37
2.400/
120
0.125/
6
VESA
800 x 600
0.323/
16
0.021/
1
1.616/
80
0.064/
3
VESA
800 x 600
0.569/
32
0.019/
1
1.138/
64
0.056/
3
VESA
1024 x 768 65.0
0.369/
24
0.062/
3
2.092/
136
0.124/
6
VESA
1024 x 768 75.0
0.320/
24
0.053/
3
1.813/
136
0.106/
6
VESA
1024 x 768 78.75
0.203/
16
0.017/
1
1.219/
96
0.050/
3
VESA
1024 x 768 94.5
0.508/
48
0.015/
1
1.016/
96
0.044/
3
VESA
1280 x 1024 108.0
0.444/
48
0.016/
1
1.037/
112
1.037
3
60.02
75.02
85.02
60.00
65.00
70.00
75.00
66.141
76.202
VESA
1280 x 1024 135.0
0.119/
16
0.013/
1
1.067/
144
0.038/
3
VESA
1280 x1024 157.5
0.406/
8
0.011
1
1.016/
160
0.033/
3
VESA
1600 x1200 162.0
0.395/
64
0.011/
1
1.185/
192
0.040/
3
VESA
1600 x 1200 175.5
0.365/
64
0.012/
1
1.094/
92
0.037/
3
VESA
1600 x1200 189.0
0.339/
64
0.011/
1
1.016/
192
0.034/
3
VESA
1600 x1200 202.50
0.316/
64
0.011/
1
0.948/
192
0.032/
3
Workstation
1152 x 900 94.2
0.425/
40
0.032/
2
1.359/
128
0.065/
4
Workstation
1152 x 900 107.50
0.223/
24
0.028/
2
1.265/
136
0.111/
8
xlvi APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
C: Back Porch
D: Blanking Period
E:Display Period
F:Total Cycle
H
µs/
Dot
V
ms/
Line
H
µs/
Dot
V
ms/
Line
H
µs/
Dot
V
ms/
Line
H
µs/
Dot
V
ms/
Line
1.907/
48
1.048/
33
6.356/
160
1.430/
45
25.442/
640
15.254/
480
31.778/ 16.683/
800 525
1.907/
54
1.111/
35
6.356/
180
1.556/
49
25.422/
720
12.712/
400
31.778/ 14.267/
900 449
3.175/
96
1.114/
39
7.407/
224
1.286/
45
21.164/
640
13.714/
480
28.571/ 15.000/
864 525
3.911/
224
0.784/
39
5.586/
320
0.865/
43
14.524/
832
12.549/
624
20.111/ 13.414/
1152 667
1.440/
144
0.568/
39
3.040/
304
0.655/
45
11.520/
1152
12.667/
870
14.560/ 13.322/
1456 915
1.838/
232
0.482/
36
3.233/
408
0.535/
40
10.143/
1280
12.841/
960
13.376/ 13.376/
1688 1000
3.810/
128
0.528/
28
5.587/
192
0.634/
40
20.317/
640
12.678/
480
26.413/ 13.735/
832 520
3.810/
120
0.427/
16
6.349/
200
0.533/
20
20.317/
640
12.800/
480
26.667/ 13.333/
840 500
2.222/
80
0.578/
25
5.333/
192
0.670/
29
17.778/
640
11.093/
480
23.111/ 11.764/
832 509
3.556/
128
0.626/
22
6.222/
224
0.711/
25
22.222/
800
17.067/
600
28.444/ 17.778/
1024 625
2.200/
88
0.607/
23
6.400/
256
0.739/
28
20.000/
800
15.840/
600
26.400/ 16.579/
1056 628
1.280/
64
0.478/
23
4.800/
240
1.373/
66
16.000/
800
12.480/
600
20.800/ 13.853/
1040 666
3.232/
160
0.448/
21
5.172/
256
0.533/
25
16.162/
800
12.800/
600
21.333/ 13.333/
1056 625
2.702/
152
0.503/
27
4.409/
248
0.578/
31
14.222/
800
11.179/
600
18.631/ 11.756/
1048 631
2.462/
160
0.600/
29
4.923/
320
0.786/
38
15.754/
1024
15.880/
768
20.677/ 16.666/
1344 806
19.20/
144
0.513/
29
4.053/
304
0.673/
38
13.653/
1024
16.599/
768
17.707/ 14.272/
1328 806
2.235/
176
0.466/
28
3.657/
288
0.533/
32
13.003/
1024
12.795/
768
16.660/ 13.328/
1312 800
2.201/
208
0.524/
36
3.725/
352
0.582/
40
10.836/
1024
11.183/
768
14.561/ 11.765/
1376 808
2.296/
248
0.594/
38
3.778/
408
0.656/
42
11.852/
1280
16.005/
1024
15.630/ 16.661/
1688 1066
1.837/
248
0.485/
38
3.022/
408
0.525/
42
9.481/
1280
12.804/
1024
12.504/ 13.329/
1688 1066
1.422/
224
0.483/
44
2.844/
448
0.527/
48
8.127/
1280
11.235/
1024
10.971/ 11.761/
1728 1072
1.877/
304
0.613/
46
3.457/
560
0.667/
50
9.877/
1600
16.000/
1200
13.333/ 16.667/
2160 1250
1.732/
304
0.566/
46
3.191/
560
0.615/
50
9.177/
1600
14.769/
1200
12.308/ 15.385/
2160 1250
1.608/
304
0.526/
46
2.963/
560
0.571/
50
8.466/
1600
13.714/
1200
11.429/ 14.286/
2160 1250
1.501/
304
0.491/
46
2.765/
560
0.533/
50
7.901/
1600
12.811/
1200
10.667/ 13.333/
2160 1250
2.123/
200
0.500/
31
3.907/
368
0.597/
37
12.229/
1152
14.522/
900
16.136/ 15.119/
1520 937
1.712/
184
0.459/
33
3.200/
344
0.598/
43
10.716/
1152
12.525/
900
13.916/ 13.123/
1496
943
APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Abmessungen
Dimensions
93.5
(3.7)
mm
(inches)
41.6
(1.6)
472
(18.6)
33.5
(1.3)
400.4
(15.7)
399
(15.7)
300.8
(11.8)
22°
3°
477.9
(18.9)
35.8
(1.4)
56.6
(2.2)
20.5
(0.8)
25° 25°
120
101.4
(4.0)
(4.7)
51.5
(2.0)
270
(10.6)
218
(8.6)
TOP VIEW
FRONT VIEW
SIDE VIEW
DRAUFSICHT
VUE D'EN HAUT
VORDERANSICHT
VUE DE FACE
SEITENANSICHT
VUE DE COTE
Pin Assignment
Pin-Belegung
Affectation des Broches
* D-Sub mini 15 pin connector
Pin No.
Signal
Pin No.
Signal
1
2
Red video
9
No pin
Green video/
Green video/
10
11
12
13
Ground
Ground
Green video
Shorted
Composite
(shorted)
Composite Sync
3
4
5
6
7
8
Blue video
Ground
Data (SDA)
H. Sync or H./V.
H. Sync/H. V.
Composite Sync
No pin
Composite sync
Red ground
Green ground
Blue ground
14
15
V. Sync
Clock (SCL)
* USB ports
Upstream
Downstream
No.
1
Signal
Comments
Cable power
Serial data
VCC
- Data
+ Data
Ground
2
3
Serial data
(Series B connector) (Series A connector)
4
Cable Ground
xlviii APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
[Applicable to gray (standard color version only).]
Congratulations!
You have just purchased a TCO’99 approved and labelled
product! Your choice has provided you with a product developed
for professional use. Your purchase has also contributed to
reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for
encouraging the adaptation of goods and services to the environment. The main problem, as
far as computers and other electronics equipment are concerned, is that environmentally
harmful substances are used both in the products and during their manufacture. Since it is not
so far possible to satisfactorily recycle the majority of electronics equipment, most of these
potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that
are important from the viewpoints of both the work (internal) and natural (external)
environments. Since all methods of electricity generation have a negative effect on the
environment (e.g. acidic and climate-influencing emissions, radioactive waste), it is vital to
save energy. Electronics equipment in offices is often left running continuously and thereby
consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’99 scheme which provides for
international and environmental labelling of personal computers. The labelling scheme was
developed as a joint effort by the TCO (The Swedish Confederation of Professional
Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation)
and Statens Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability,
emission of electric and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among
other things. The product must be prepared for recycling and the manufacturer is obliged to
have an environmental policy which must be adhered to in each country where the company
implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a
certain period of inactivity, shall reduce its power consumption to a lower level in one or
more stages. The length of time to reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the
reduction of electric and magnetic fields, physical and visual ergonomics and good usability.
Below you will find a brief summary of the environmental requirements met by this
product.
The complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO’99 approved and labelled products may also be
Download from Www.Somanuals.com. All Manuals Search And Download.
[Applicable to gray (standard color version only).]
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and
housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of
the plastic in a computer casing can consist of flame retardant substances. Most flame
retardants contain bromine or chloride, and those flame retardants are chemically related to
another group of environmental toxins, PCBs. Both the flame retardants containing bromine
or chloride and the PCBs are suspected of giving rise to severe health effects, including
reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*
processes. Flame retardants have been found in human blood and researchers fear that
disturbances in foetus development may occur.
The relevant TCO’99 demand requires that plastic components weighing more than 25
grams must not contain flame retardants with organically bound bromine or chlorine. Flame
retardants are allowed in the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of
certain computer displays. Cadmium damages the nervous system and is toxic in high doses.
The relevant TCO’99 requirement states that batteries, the colour-generating layers of
display screens and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous
system and is toxic in high doses. The relevant TCO’99 requirement states that batteries
may not contain any mercury. It also demands that mercury is not present in any of the
electrical or electronics components associated with the labelled unit.
CFCs (freons)
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used during
the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing
printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased
risks of skin cancer (malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages
the nervous system and in higher doses, causes lead poisoning. The relevant TCO’99
requirement permits the inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
Download from Www.Somanuals.com. All Manuals Search And Download.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: 562 431 5011
declare that the product
Trade name: EIZO
Model: FlexScan L771
is in conformity wit
h Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provid
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures.
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
*Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to
keep interference within the limits of a Class B digital device.
-AC Cord
-Shielded Signal Cable (D-SUB mini 15 pin - D-SUB mini 15 pin, the enclosed signal cable)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
For Europe, etc. (220-240 Vac) Only
CE Marking
Declaration of Conformity
Kind of equipment:
Type-designation:
Monitor
L771
is in compliance with:
Council Directive 73/23/EEC
Council Directive 89/336/EEC
EN60950: 1992+A1+A2+A3+A4+A11
EN55022 (class A): 1998
EN50082-1: 1992
EN61000-3-2: 1995+A1+A2 EN61000-3-3: 1995
Konformitätserklärung
Geräteart :
Gerätetyp :
Monitor
L771
den folgenden Normen oder Vorschriften entspricht:
EU-Richtlinie 73/23/EEC
EU-Richtlinie 89/336/EEC
EN60950: 1992+A1+A2+A3+A4+A11
EN55022 (class A): 1998 EN50082-1: 1992
EN61000-3-2: 1995+A1+A2 EN61000-3-3: 1995
Déclaration de conformité
Nature de l’équipement :
Type-désignation :
Moniteur
L771
est en conformité avec :
Directive Européenne 73/23/EEC EN60950: 1992+A1+A2+A3+A4+A11
Directive Européenne 89/336/EEC EN55022 (class A): 1998 EN50082-1: 1992
EN61000-3-2: 1995+A1+A2 EN61000-3-3:1995
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1/59-98, EK1/60-
98 mit dem Videosignal, 1600 Punkte x 1200, RGB analog, 0,7 Vp-p und mindestens
60,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen
Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu
verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem
Zeichenkontrast.)
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in
Deutschland zusammen mit dem Partner von Roll MBB Recycling GmbH.
Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung
zugeführt werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu
erfahren, benutzen Sie bitte folgende Rufnummer: 02153-73 35 00. Weitere
Informationen finden Sie auch unter der Internet-Adresse: www.eizo.de.
Download from Www.Somanuals.com. All Manuals Search And Download.
|