M6784
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools required for assembly: Phillips Screwdriver, Hammer and Scrap Block of Wood (not included).
Requires three "AA" batteries (included).
Age: 2-6 years.
Weight limit: 60 lbs (27 kg).
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Rear Wheel
(Indented Side Up)
Cap Nut
Hubcap
(Peg Side Down)
Straight Axle
Cover
Frame
Rear Wheel
(Indented Side Down)
Hubcap
Hubcap
(Peg Side Up)
Assembled
Rear Wheel
Straight Axle
Scrap Block
of Wood
Cap Nut
Assembly Tool
3
1
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
Frame
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle. Tap the
cap nut with a hammer. Gently pull the rear wheel up
to be sure the cap nut is securely attached to the
straight axle.
• Insert one of the tabs on a cover into a slot in the hubcap.
Push to snap the cover into place. Repeat this procedure
to attach the other cover to the other hubcap.
Hole
Hole
Pedal Hub
Tab
Pedal Axle
Tab
Slot
Straight Axle
Pedal Hub
2
4
BOTTOM VIEW
• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs fit into the slot in each pedal hub.
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pedal Hubs
Pedal
Pedal Axle
Front Wheel
Pedal Axle
Hole
5
Scrap Block of Wood
• While holding the pedal hubs
on the pedal axle, insert the
pedal axle through the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
7
• Fit the pedal on the pedal axle. Tap the pedal with
a hammer until it is secure.
• Pull the pedal up to be sure it is secure. If you can remove
it, you have not secured it properly. Tap it with the
hammer again.
Pedal Hub
Fork Arms
Fork Cover
Pedal Hub
Groove
8
6
Pedal Axle
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x 3/4" screws into the fork cover and tighten.
• Turn the front wheel
assembly over.
• Insert the remaining pedal hubs on top of and below the
pedal axle and into the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
FIRST, insert the
screw so that 3/4" is
visible. THEN,
Slot
Handlebar
Headlight Cover
tighten the screw.
3/4"
Frame
Neck
Fork
Post
Fork Cover
Rear of Trike
9
11
• Fit the tab on the headlight cover to the slot in the top of
the handlebar.
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
• Place the handlebar onto the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
• Insert two #8 x 3/4" screws into the headlight cover. Tighten
the screws.
Seat Retainer
Hint: You may need to rotate the handlebar to align the holes.
Seat
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post so that part of the screw (about 3/4")
is still visible. Tighten the screw.
Peg
Cap
Holes
12
• Position the seat upside down.
• Fit the small pegs on the seat retainer into the holes in
the seat.
10
• Insert and “snap” the cap into the hole in the frame.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Label Decoration
Attaching the Seat
Helpful Hint: The seat can be attached to the frame in any of
three positions, depending on the size of your child. Check
your child’s fit on the trike by observing the seat to pedal
distance, as it is being ridden. If the pedals seem too far
away or too close for your child, move the seat up or down.
(Place label 7 on
opposite side)
(Place label 15
6
on opposite side)
11
16
9
Seat
Tabs
12
(Place label 13
on opposite side)
Seat
Retainer
14
Slots
4
1
(Place label 3
on opposite side
of seat)
(Place label 2 on
opposite side)
8
(Place remaining
label 8’s on
opposite side of
front wheel)
SIDE VIEW
Middle Position
Lower Position
Upper Position
• At an angle, insert the tabs on the seat into any of the top
three sets of slots for the lower, middle or upper position.
• Lower the seat so that the seat retainer inserts and snaps
into the slots in the frame.
• Pull up on the seat to be sure it is secure.
5
10
DASH VIEW
• Make sure the areas where the labels will be applied are
clean and dry. Wipe your vehicle with a clean, soft, dry
cloth to remove any dust or oils.
• For best results, avoid applying a label more than once.
• Apply the labels as shown in the illustration above.
• After applying the label, rub the label firmly with a cloth to
make sure the label is adhered to your vehicle.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Replacement
Battery Safety Information
Note: For best performance, we recommend replacing the
batteries that came with this trike with three, new alkaline
"AA" (LR6) batteries.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
Headlight Cover
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Care
• Check the plastic parts regularly and if broken or cracked,
dispose of them properly.
• Check all fasteners regularly to be sure they are tight.
If the fasteners are not tight, tighten them as necessary.
1
• Loosen and remove the two screws from the headlight
cover. Remove the headlight cover.
• To clean, use a mild soap and water solution and a clean
cloth. Rinse clean with water to remove soap residue.
Battery Compartment
FCC Statement
United States Only
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
2
1.5V x 3
“AA” (LR6)
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
Hint: When sound or lights become faint or stop, it's time
for an adult to replace the batteries. We recommend the
use of alkaline batteries for longer battery life.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
• Loosen the screw in the battery compartment door. Open
the battery compartment door.
• Insert three "AA" (LR6) alkaline batteries.
• Close the battery compartment door and tighten the screw.
• Replace the headlight cover. Replace the screws
and tighten.
• Protect the environment by not disposing of this
product with household waste (2002/96/EC). Check
your local authority for recycling advice and facilities
(Europe only).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Seat
Consumer Information
Seat
Seat Retainer Tab
Frame
Seat Retainer Tab
IMPORTANT! It is good practice to start training children
very young regarding the importance of helmet use. When
children are older and riding bicycles and faster vehicles,
it is important that they use a helmet each and every time
they ride. For this reason, even while riding a tricycle, it is
a good idea to familiarize your child with helmet use, so that
it becomes a habit for life. Choose a helmet that complies
with requirements of the applicable certifying agency for
bicycle helmets.
• Turn the frame on its side.
• Squeeze the seat retainer tabs toward one another and lift
the seat from the frame.
Let's Go!
Right Turn
Left Turn
Motorcycle
Signal
Signal
Sounds
Power
Music
Horn
Music
Horn
™
Batman
Bat call
phrases
Ignition
• Slide the power switch on
.
• Turn the ignition, “VRROOOM!”
• Press the left or right turn signals for flashing blinkers.
• Press any of the buttons for motorcycle sounds, a horn,
™
music, Batman phrases and bat calls!
DC SUPER FRIENDS and all related characters and elements are trademarks of © DC Comics.
TM & © Warner Bros. Entertainment Inc.
TM
(s07)
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO
M6784pr-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
|