Our Thanks to You and
Customer Assistance
Introduction
Owner’s Manual
Our Thanks to You
•
Thank you for purchasing a Cobra Bluetooth Handset.
Properly used, this Cobra product will give you many years
of reliable service.
How Your Cobra Bluetooth Handset Works
This handset allows use of mobile telephones (cell phones) while protecting them
from potential damage in the outdoor environment.
Bluetooth wireless technology allows voice and data transmission over short
distances by means of a radio link. Using that technology, the Bluetooth handset
allows your cell phone to be turned on and stowed in a waterproof and protected
location on the vehicle. Calls are then made and received using the Bluetooth
handset.
Customer Assistance
Customer Assistance
•
Should you encounter any problems with this product, or not understand its
many features, please refer to this owner’s manual. If you require further
assistance after reading this manual, Cobra Electronics offers the following
customer assistance services:
For Assistance in the U.S.A.
Automated Help Desk English only.
24 hours a day, 7 days a week 773-889-3087 (phone).
Customer Assistance Operators English and Spanish.
8:00 a.m. to 5:30 p.m. Central Time Mon. through Fri. (except holidays)
773-889-3087 (phone).
Questions English and Spanish.
Faxes can be received at 773-622-2269 (fax).
Technical Assistance English only.
English and Spanish. productinfo@cobra.com (e-mail).
®
BLUETOOTH HANDSET
For Assistance Outside the U.S.A.
BT 200
©2008 Cobra Electronics Corporation
6500 West Cortland Street
Chicago, Illinois 60707 USA
English
A1
Nothing Comes Close to a Cobra®
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Introduction
Our Thanks to You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Handset Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2
Backlit LCD (Liquid Crystal Display) Screen . . . . . . . . . . . . . . . . . . . . . . . A3
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Trademark Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation
Included in this Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating Your Handset
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Common BT 200 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Customizing the BT 200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warranty
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Product Service
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Nothing Comes Close to a Cobra®
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
Included in this Package
Introduction
Installation
Important Safety Information
Included in this Package
•
•
Before installing and using your Bluetooth handset, please read these general
precautions and warnings.
You should find all of the following items in the package with your Cobra
Bluetooth handset.
Warning and Notice Statements
Handset
Operating Instruction Manual
To make the most of this Bluetooth handset, it must be installed and used properly.
Please read the installation and operating instructions carefully before installing and
using the handset. Special attention must be paid to the WARNING and NOTICE
statements in this manual.
WARNING
Statements identify conditions that could result in personal injury or loss of life.
NOTICE
Statements identify conditions that could cause damage to the handset,
other equipment or stored data.
General Precautions
12V DC Adapter
Peel and Stick Hanger Bracket
The following NOTICES information is important to your operation of the handset.
FCC NOTICES
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two (2) conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Optional
Screws
NOTICES
AVOID using your Bluetooth handset at temperatures below -4°F (-20°C) or
above 131°F (55°C).
AVOID storing your Bluetooth handset at temperatures below -4°F (-20°C)
or above 158°F (70°C).
DO NOT attempt to service any internal parts yourself. Have any necessary
service performed by a qualified technician.
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could
void the user's authority to operate the equipment.
Nothing Comes Close to a Cobra®
3
English
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Getting Started
Installation
Installation
Getting Started
Installation
•
•
Refer to the foldout at the front of this manual to identify the various controls and
indicators on your Bluetooth handset.
Most button functions are activated by a momentary press, then release. In those
cases that call for “press and hold,” hold the button down for at least two seconds
after it is pressed. The PTT button is held down as long as you are speaking into
the microphone.
Installing the Hanger Bracket
1. Install the hanger bracket on a vertical surface
Hanger Bracket
near the bulkhead connector using the supplied
peel and stick adhesive*. The optional stainless steel
screws can also be used.
When using the handset, tones will sound to:
I
Indicate an error – three beeps.
*Be sure to clean the mounting surface with isopropyl
alcohol prior to mounting unit with peel and stick adhesive.
I
Confirm an action – two beeps.
Confirm a single button press (except the PTT button) – one beep.
I
You can turn the Key Tones Off if you want (see page 21).
Try It Out
Using the Bluetooth handset is the most effective way to learn about it. Don’t
hesitate to explore functions and add entries to see how they work. Do not be
concerned if you make mistakes. They can all be undone in Edit mode. Or you
can reset the unit to the original factory default condition. Push and hold the
Green Phone and Home function keys, then push the Power key until the
unit turns On.
NOTICE
Resetting the unit will clear ALL Bluetooth device pairings as well as the
Call Log, Phonebook and Bluetooth device list.
Nothing Comes Close to a Cobra®
5
English
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Common BT 200 Functions
Common BT 200 Functions
Operating Your Handset
Operating Your Handset
Common BT 200 Functions
VOX
•
The VOX function converts the handset microphone’s pickup of your voice from
being controlled by the PTT button to being activated by your voice. When VOX
is On, the PTT button does not need to be pushed to transmit your voice and
you can just speak into the microphone.
The following procedures define common operating functions of the handset.
Power On/Off
Press the Power button at the top of the handset for two seconds to turn it On
or Off.
When VOX is Off, you need to push the PTT button while speaking.
The first time you turn On the Cobra Bluetooth handset you will see a message that
the unit is ready for pairing with a cell phone. The message also provides a
password. If you do not want to pair a device right away, press the Escape button to
go to Standby mode.
When the unit is subsequently turned On, it will search for the currently selected
Bluetooth device and go to Standby mode.
To Change Between VOX On and Off:
1. Press and hold the Mode button for two seconds while a call is in progress.
NOTE
When the VOX function is On in noisy environments, the caller connected
to the BT 200 might hear some of your background noise.
Mode
Back Light/Lock
This button serves two functions:
This button serves two functions:
I
To change the mode of operation between the Bluetooth handset and
your cell phone itself.
I
To turn the display back light On and Off.
I
To lock and unlock most of the buttons on the handset.
I
To switch voice activation of the microphone between On and Off. Turn VOX On
if you want to operate in a hands-free mode similar to a Bluetooth speakerphone.
Back Light
Mode
A light is provided behind the LCD screen to improve visibility of the information
provided there. However, you can turn the light On or Off at will.
Normal operation of the Cobra Bluetooth handset uses its internal microphone
and speaker to conduct conversations during a call. However,
there may be times you want to suspend the Bluetooth pairing and continue
part or all of the call on your cell phone itself.
To Turn the Back Light On or Off:
1. Press the Back Light/Lock button.
Lock
To Change Between Handset and Cell Phone Modes:
The Lock function disables the operation of all buttons except PTT, Back Light/Lock
and Power buttons. When Lock is On, accidental presses of any of the other buttons
are ignored by the unit. A call can be continued if it was started before Lock was
turned On, but new calls cannot be made or answered when Lock is On.
1. Press the Mode button to switch the call to your cell phone.
2. Talk and listen to your cell phone in the usual way. The handset will be inactive.
3. Press the Mode button to restore operation to the handset.
4. Talk and listen to the call on the Bluetooth handset.
To Turn Lock On or Off:
1. Press and hold the Back Light/Lock button for two seconds.
Nothing Comes Close to a Cobra®
7
English
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Common BT 200 Functions
Common BT 200 Functions
Operating Your Handset
Operating Your Handset
Push to Talk (PTT)
Home Button
This button serves two functions:
Pressing this button enables you to return the handset to Standby mode from
any other mode.
I
To activate the handset microphone during a call when VOX is Off. This is similar
to the action of such a button on a Cobra VHF or a CB radio.
Voice Dialing / Last Number Redial
This button serves two functions:
I
To activate the handset microphone for a PA announcement, the unit must be in
Standby and be connected to the stereo’s AUX input with the stereo in AUX mode.
I
To enable voice dialing.
To Activate the Handset Microphone During a Call:
1. After placing or accepting a call, press the PTT button and talk into the handset
microphone.
I
To redial the last number dialed from the handset.
Voice Dialing
You can activate your cell phone's voice dialing feature from Standby mode.
To Make a PA Announcement:
1. When the unit is in Standby mode, press the PTT button and talk into the
microphone.
To Voice Dial A Number:
1. Press and release the Voice Dialing / Last Number Redial button.
2. Say the name or phone number command following the audio prompt.
The display screen will show the progress of dialing and connecting the call.
NOTE
Before a PA announcement can be made:
I
The PA function must be turned ON from the settings menu.
The BT 200 must be connected to the stereo system AUX input.
NOTE
I
Your cell phone must have voice dialing enabled and voice commands
recorded to use this feature with the BT 200.
I
The stereo must be in AUX mode with the stereo’s volume adjusted.
I
An optional installation cable is necessary to use the PA feature.
To Redial The Last Number Dialed:
1. Press and hold the Voice Dialing / Last Number Redial button for two seconds.
The display screen will show the progress of dialing and connecting the call.
Green Phone Button
This button acts just like the green phone button on a cell phone. Pressing the
button answers an incoming call and initiates dialing an outbound call after the
number has been entered or selected.
In Standby mode, this button is a shortcut to the Call Log where a number can be
selected to call.
Function Buttons
The Function buttons provide different utilities to different modes of handset
operation. In any mode, the active functions are shown directly above the buttons
on the display screen as shown in this Standby display.
In this example, pressing the second button from the
Functions
Red Phone Button
This button acts just like the red phone button on a cell phone. Pressing the button
ends an active call.
left will display the Menu.
PAIRED TO
XXX
In modes other than an active call, it backs up to the Standby mode.
Function Names
Function Buttons
CONT
MENU
LOG
VOL
Nothing Comes Close to a Cobra®
9
English
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Operating Your Handset
Operating Your Handset
Operation
Call Waiting
•
When a second call rings during an active call, it will be announced on the
handset screen.
Once the Cobra Bluetooth handset has been paired with a cell phone, incoming calls
can be answered and outgoing calls can be made.
Call Waiting Display
To Answer the Waiting Call:
Standby
1. Press the Answer Function button. The waiting call
will become active, the first call will be put on hold.
While waiting to receive or make a call, the handset will be in Standby mode.
INCOMING CALL
The upper part of the screen shows the Waiting For A Call
icon and the cell phone signal strength.
Standby Mode
+1 555 566 1234
ANSWER
IGNORE
The Function buttons (from left to right) will activate display
of the Volume screen, the Menu screen, the Call Log screen
and the Phonebook screen.
PAIRED TO
XXX
CONT
MENU
LOG
VOL
The Up and Down Arrow buttons will also adjust handset
speaker volume directly while in Standby or during a call.
Outgoing Call
Outgoing calls can be initiated in three ways:
Incoming Call
I
By selecting a Phonebook entry.
When the active paired cell phone receives a call, the ring tone will sound and it will
be announced on the handset screen.
I
By selecting a Call Log entry.
I
By dialing the number using handset Function buttons.
Incoming Call Display
Ringing
Phonebook
The call can be answered by pressing either the Answer
Function button or the Green Phone button.
If the Ignore Function button is pressed, the call will not
be accepted, but will be recorded in the Call Log.
INCOMING CALL
After adding a number to your Phonebook, you can go to the Phonebook and select
it from the available numbers to be dialed.
To access a number in the Phonebook, press the Menu Function button in Standby
mode, then select the Phonebook mode to arrive at the screen shown.
+1 555 566 1234
ANSWER
IGNORE
Answered Call
The Mute Function button will disable the microphone,
but allow you to continue to hear the calling person.
To end the call and return to Standby mode, press either
the End Function button or the Red Phone button.
Caller information like name and number of the incoming
caller will only be shown if it is available on your network
and/or device.
Phonebook
Select and Dial a Number
To Select and Dial a Number:
1. Use the Page Up and Page Down buttons to shift up and
down the list of entries.
2. Use the Up and Down Arrow buttons to scroll the pointer
at the left of the screen to the desired entry.
3. Press the Green Phone button to call the number.
Answered Call Display
1
BILL CELL
NATALIE
NAT CELL
BILL DESK
ADD NEW
EXIT
2
3
4
CONNECTED
NEW
EDIT
PG
PG
+1 555 566 1234
MUTE
END
Nothing Comes Close to a Cobra® 11
English
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Operating Your Handset
Operating Your Handset
Call Log
Bluetooth Phone Setup and Switching
The most recent incoming and outgoing calls are recorded in the handset Call Log.
These can be used to select and dial a number.
The Cobra Bluetooth handset can be paired with only one device at a time.
However, it can store pairing information on up to eight different devices.
To access a number in the Call Log, press the Menu Function button in Standby
mode, then select the Call Log mode to arrive at the screen shown.
Setup
To Begin Phone Setup or To Switch To Pair With
a Different Device:
1. Press the Menu button in Standby mode, then select the
Bluetooth Phone Setup mode to arrive at the screen shown.
2. At this screen, use the Up and Down Arrow buttons
Call Log
Select and Dial a Number
NEW
DELETE
DISABLE
SWITCH
To Select and Dial a Number:
1. Use the Page Up and Page Down buttons to shift up
1
1
BILL ANDERSON
1 555 588 2300
JANE DOE
1 555 600 4300
MARY WILLIAMS
1 555 250 4343
PG
2
3
4
5
6
and down the list of entries.
to move the pointer to the desired function. Then press the
Enter button to select the function and advance to its screen.
2. Use the Up and Down Arrow buttons to scroll the pointer
at the left of the screen to the desired entry.
PG
VIEW
3. Press the Green Phone button to call the number.
New
New can be used to add a device to those already paired or to pair a device
if you did not do so at the initial Power On of the BT 200.
NOTE While in Call Log mode, you can see details of the
selected entry by pressing the View Function button
or Enter button.
To Add a New Cell Phone:
1. Select New on the Phone Setup screen to advance
to the screen shown.
Add a New Cell Phone
READY FOR PAIRING
TO YOUR PHONE
2. Follow the cell phone’s instructions to search for available
pairing with another Bluetooth device. This can often be
found in the Tools or Settings menu of your mobile phone.
3. Wait for the pairing process to complete.
You will then see a confirmation of successful pairing
or a notice to try again if pairing did not occur.
Dial Number
PASSWORD IS 0000
2:59 MNTS REMAINING
To enter a number you want to dial, press the Menu Function button in Standby
mode, then select the Dial By Number mode to arrive at the screen shown.
To Enter a Number to be Dialed:
Dialing a Number
1. Press and release the Function button under the first digit
of the phone number until the correct number appears
above the flashing cursor.
2. Wait for the cursor to shift to the right or press the Enter
button to shift the cursor.
ENTER NUMBER
The newly paired cell phone will become the active one
that is used for calls until you Switch to another.
4 5 6
7 8 9
0+
#
1 2 3
*
Delete
Delete is used to remove the pairing information for a device from the
handset memory.
3. Enter the second digit of the phone number as in step 1.
4. Repeat steps 1 and 2 until the complete number has
been entered.
Delete a Cell Phone
To Delete a Cell Phone:
5. Press the Green Phone button to call the number.
1. Select Delete on the Phone Setup screen to advance
to the screen shown.
BILL ANDERSON
JANE DOE
WIFES PHONE
2. Use the Page Up and Page Down buttons to shift up
NOTE The number will appear on the screen without
PG
PG
DEL
EXIT
and down the list of entries three items at a time.
dashes or other separators.
3. Use the Up and Down Arrow buttons to scroll the
pointer at the left to the screen to the desired entry.
4. Press the Delete Function button to remove the
device from the list.
Nothing Comes Close to a Cobra® 13
English
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Product Features
Customizing the BT 200
Product Features
OperatingYour Handset
OperatingYour Handset
Disable
Customizing the BT 200
•
Disable prevents pairing with a device, but does not remove it from the list
or its pairing data from the handset memory.
Your Cobra Bluetooth handset allows you to customize its operation to match your
preferences. Features you can adjust have the following defaults when the unit is
new or after a reset:
To Disable a Cell Phone:
1. Select Disable on the Phone Setup screen to advance
to the screen shown.
2. Use the Page Up and Page Down buttons to shift up
and down the list of entries three items at a time.
3. Use the Up and Down Arrow buttons to scroll the
pointer at the left to the screen to the desired entry.
Disable a Cell Phone
I
I
I
I
I
I
I
I
I
I
I
I
VOX: Off
PA Output: Off
Display Brightness: high
Ring Tone: #1
Call Log: cleared
BT Device List: cleared
Display Contrast: 8
Button Tones: On
Phonebook: cleared
Volume: 75%
Auto Dim: Off
BT Region: USA and EUROPE
BILL ANDERSON
JANE DOE
WIFES PHONE
X
X
PG
PG
X
EXIT
4. Press the X Function button to disable an available
device or to enable a disabled device.
Menu
An X at the right of an entry indicates that it is in
The customizable features on your handset are reached from the Menu mode.
disabled status.
To begin customizing your handset, press the Menu Function
Menu
button in Standby mode to arrive at the screen shown.
The Menu options list appears on the screen.
The complete list is:
Switch
PHONEBOOK
CALL LOG
The Switch function allows you to select which device will be used for calls from
the list of those available.
DIAL BY NUMBER
PA OUTPUT
BLUETOOTH PHONE STUP
SETTINGS
EXIT
I
I
I
I
I
I
I
Phonebook
Call Log
PA Output
Settings
MORE
To Switch From One Active Cell Phone to Another:
1. Select Switch on the Phone Setup screen to advance
to the screen shown.
2. Use the Page Up and Page Down buttons to shift up
and down the list of entries three items at a time.
3. Use the Up and Down Arrow buttons to scroll the pointer at
the left of the screen to the cell phone which you want to
make active.
Switch From One Active
Cell Phone to Another
Dial By Number
Bluetooth Phone Setup
Exit
BILL ANDERSON
JANE DOE
WIFES PHONE
X
X
You can scroll through the list one entry at a time by
use of the Up and Down Arrow buttons.
Once the pointer at the left of the screen is positioned at the
option you want, press the Enter button to select it and
advance to its screen.
DEL
EXIT
PG
PG
4. Press the Enter button to begin the process of re-pairing to
the selected device.
Nothing Comes Close to a Cobra® 15
English
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the BT 200
Customizing the BT 200
OperatingYour Handset
OperatingYour Handset
NOTE
Phonebook Entries
If corrections are needed before saving the entry, press the Left or Right
Arrow Function button to move the cursor to the character that is to be
changed and press the Delete Function button to remove that character.
Then scroll the list to select the correct character.
The Operation section described using a Phonebook entry to dial an outgoing call.
Both names and numbers can be stored in the Phonebook.
Add New
To Enter a New Name and Phone Number
1. Select Phonebook from the Menu function and scroll
the pointer down to Add New at the bottom of the list
to arrive at the screen shown.
2. Press the Enter or New Function button to advance
to the Phonebook Edit mode.
+1 555 588 2300
JANE DOE
ADD NEW
EXIT
49
50
NOTE
A “double click” on the Delete Function button will remove the entire entry
and return the cursor to the initial position after Name.
NEW
EDIT
Phonebook Edit
To Edit an Existing Name or Phone Number:
1. Select Phonebook from the Menu function, scroll down to
3. Press the Up or Down Arrow button to scroll the
alphanumeric list to the first character of the Name.
NAME : BILL ANDERSON
NUMBER: +1 555 566 1234
name or number to be edited and press the Edit Function
Enter a New Name
and Phone Number
button to arrive at the screen shown.
NOTE
DEL
SAVE
2. Use the Right and Left Arrow Function buttons to move
the cursor to the character(s) to be changed and proceed
as described for making corrections when entering a new
name or number.
The list consists of the letters A to Z followed by the
numbers 0 to 9 followed by +, “space,” *, and # and
it will wrap around from # to A.
NAME :
NMB:
DEL
SAVE
3. Press the Save Function button to save the changes or
deletion and go back to the Phonebook function.
NOTE
If only a number (without a name) is to be entered,
at step 3, press the Right Arrow Function button until
the cursor moves to the first character of the number
and jump to step 7.
PA Output
If, during installation, you have connected the Cobra Bluetooth handset connection
cable to your vessel’s stereo AUX input, you can allow the handset
to be used as a public address microphone.
4. When the first character appears above the cursor, press
the Enter or PTT button to save the character and move
the blinking cursor to the right.
Enable Use of
Auxiliary Speakers
To Enable Use of Auxiliary Speakers:
1. Select PA Output from the Menu function to arrive at
the screen shown.
2. Press the On or Off Function button to toggle between
On and Off condition.
5. Repeat step 4 until the entire name has been entered.
PA OFF
6. Continually press or press and hold the Right Arrow
Function button until the cursor moves to the first
character of the Number.
ON
OFF
7. Enter the phone number in the same fashion as the name.
8. Press the Save Function button to save the entry and go
back to the Phonebook function.
NOTE
An optional installation cable is necessary to use the PA feature.
Nothing Comes Close to a Cobra® 17
English
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the BT 200
Customizing the BT 200
OperatingYour Handset
OperatingYour Handset
Display
Settings
The Display function adjusts the lighting of the LCD screen and includes three
separate adjustments: Brightness, Contrast and Auto Dim.
The Settings option on the Menu provides access to the remaining functions needed
to customize your handset.
To access these functions, select the Display option from
Display Settings
To access these functions, select the Settings option from
Settings Menu
Settings mode to arrive at the screen shown.
the Menu to arrive at the screen shown.
VOLUME
DISPLAY
VOX
RING TONES
KEY TONE
BT REGION SET
You can scroll the list using the Up and Down Arrow
buttons.
Once the pointer at the left of the screen is positioned at
the option you want, press the Enter button to select it and
advance to its screen.
The Settings options list appears on the screen.
The complete list is:
BRIGHTNESS
CONTRAST
AUTO DIM
I
I
I
I
I
I
I
Volume
VOX
Key Tones
Exit
Display
Ring Tones
BT Region
To Adjust the Screen Brightness:
1. Select Brightness from the Display mode to advance to
the screen shown.
2. Press the Up or Down Arrow or Up or Down Function
button to step through the available settings of High,
Medium, Low and Off.
Adjust Screen Brightness
Once the pointer at the left of the screen is positioned at the
option you want, press the Enter button to select it and
advance to its screen.
BRIGHTNESS ADJUST
HIGH
DOWN
UP
SAVE
3. At the desired setting, press the Enter or Save Function
button to save the setting and return to Display function.
Volume
This volume adjustment can be performed on the internal speaker in the handset
either from Standby mode or during a call.
To Adjust the Screen Contrast:
Adjust Screen Contrast
Adjust Handset Volume
1. Select Contrast from the Display mode to advance to the
To Adjust the Handset Volume:
1. Select Volume from the Settings function to arrive at the
screen shown.
2. Press the Up or Down Arrow buttons or the Up or Down
Function buttons to adjust the speaker volume. The bar
graph will show the level you have set.
3. Press the Enter or Save Function button to save the
volume setting and return to Settings function.
CONTRAST ADJUST
screen shown.
VOLUME ADJUST
UP
8
2. Press the Up or Down Arrow or Up or Down Function
button to step through the available settings. The range is
from a minimum at 0 to a maximum at 16.
3. At the desired setting, press the Enter or Save Function
button to save the setting and return to Display function.
SAVE
DOWN
UP
DOWN
SAVE
Nothing Comes Close to a Cobra® 19
English
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the BT 200
Customizing the BT 200
OperatingYour Handset
OperatingYour Handset
Adjust Auto Dim
To Set Auto Dim On or Off:
Ring Tones
1. Select Auto Dim from the Display mode to advance to
Ten different ring tones are available from which to choose.
AUTO DIM
OFF
the screen shown.
Select a Ring Tone
To Select a Ring Tone:
2. Press the Off or On Function button to select the
desired condition.
3. Press the Enter button to save the setting and return
to Display mode.
1. Select Ring Tones from Settings mode to advance
OFF
ON
RING TONE SELECT
to the screen shown.
R 01
2. Press the Up Arrow or Down Arrow button to scroll
through the tones from 01 to 10.
PLAY
SAVE
NOTE
3. Press the Play Function button to hear the selected tone.
When Auto Dim is set to On, the LCD screen backlight
will be turned Off after 15 seconds if no button is
pressed. It will be turned On for 15 seconds following
any button press except PTT.
4. Press the Enter or Save Function button to save the
tone and return to Settings mode.
Key Tones
Key tones confirm button presses for all but the PTT button.
Set Key Tones
VOX
To Set Key Tones On or Off:
The VOX function can be turned On or Off directly with the Mode button as
described on page 7 or from the Menu.
1. Select Key Tones from Settings mode to advance
KEY TONES
to the screen shown.
ON
To Set VOX On or Off from the Menu:
VOX Setting
2. Press the Off or On Function button to select the
desired condition.
3. Press the Enter or PTT button to save the setting
and return to Settings mode.
OFF
ON
1. Select VOX from Settings mode to advance to the
VOX
OFF
screen shown.
2. Press the Off or On Function button to select the desired
condition.
ON
OFF
Bluetooth Region
3. Press the Enter button to save the setting and return
to Settings mode.
Different parts of the world use different sets of radio frequencies for Bluetooth
pairing. You can select from four regions for handset operation: (1) USA - Europe,
(2) France, (3) Spain and (4) Japan. Most users will not need to change these
settings.
NOTE
The VOX On or Off setting will be retained when the
unit is turned Off.
Setting BT Region
To Select A Bluetooth Region:
1. Select BT Region from the Settings function to arrive
at the screen shown.
BT REGION SET
USE - EUROPE
FRANCE
*
SPAIN
2. Press the Up or Down Arrow buttons or the Up or Down
Function buttons to scroll through the list.
SAVE
3. Once the pointer at the left of the screen is positioned
at the region you want, press the Enter, PTT or Save
Function button to save the setting.
Nothing Comes Close to a Cobra® 21
English
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and
Product Service
Warranty
Warranty
ProductService
Limited 1-Year Warranty
Maintenance
•
•
For Products Purchased In The U.S.A.
Very little maintenance is required to keep your Cobra Bluetooth handset in good
operating condition:
Cobra Electronics Corporation warrants that its Cobra Bluetooth handset, and the component
parts thereof, will be free of defects in workmanship and materials for a period of one year
from the date of first consumer purchase. This warranty may be enforced by the first
consumer purchaser, provided that the product is used within the U.S.A.
I
Keep the handset clean by wiping with a soft cloth and mild detergent. Do not use solvents
or harsh or abrasive cleaners, which could damage the case or scratch the LCD screen.
I
I
If the handset is exposed to salt water, wipe with a soft, moist cloth at least once a day to
prevent buildup of salt deposits, which could interfere with button operation.
Cobra will, without charge, repair or replace, at its option, defective handsets, products or
component parts upon delivery to the Cobra Factory Service department, accompanied by
proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt.
To determine the software version in your handset, press and hold the PTT button
while turning On the power. The version number will show on the LCD screen for
five seconds, then proceed to normal startup.
You must pay any initial shipping charges required to ship the product for warranty
service, but the return charges will be at Cobra’s expense, if the product is repaired or
replaced under warranty. This warranty gives you specific legal rights, and you may also
have other rights which may vary from state to state.
Product Service
•
For any questions about operating or installing this new Cobra product, or if parts are
missing…PLEASE CALL COBRA FIRST…do not return this product to the store.
Exclusions. This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product, or as a result
of unauthorized alterations or repairs.
If this product should require factory service, please call Cobra first before sending the product.
This will ensure the fastest turnaround time on any repair. If Cobra asks that the product be sent
to its factory, the following must be furnished to have the product serviced and returned:
1. For Warranty Repair include some form of proof-of-purchase, such as a mechanical
reproduction or carbon of a sales receipt. Make sure the date of purchase and product
model number are clearly readable. If the originals are sent, they cannot be returned.
3. If the serial number has been altered, defaced or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness for a particular
purpose are limited in duration to the length of this warranty. Cobra shall not be liable for
any incidental, consequential or other damages; including, without limitation, damages
resulting from loss of use or cost of installation.
2. Send the entire product.
3. Enclose a description of what is happening with the product. Include a typed or clearly
printed name and address of where the product is to be returned, with phone number
(required for shipment).
4. Pack the product securely to prevent damage in transit. If possible, use the original
packing material.
Some states do not allow limitations on how long an implied warranty lasts and/or do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitations may not apply to you.
5. Ship prepaid and insured by way of a traceable carrier such as United Parcel Service
(UPS) or Priority Mail to avoid loss in transit to:
Cobra Factory Service, Cobra Electronics Corporation
6500 West Cortland Street, Chicago, Illinois 60707 U.S.A.
For Products Purchased Outside The U.S.A.
6. If the product is in warranty, upon receipt of the product, it will either be repaired or
exchanged depending on the model. Please allow approximately 3 – 4 weeks before
contacting Cobra for status. If the product is out of warranty, a letter will automatically
be sent with information as to the repair charge or replacement charge.
For any questions, please call 773-889-3087 for assistance.
Nothing Comes Close to a Cobra® 23
English
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Notes
The Cobra line of quality products includes:
CB Radios
®
microTALK Radios
Radar/Laser Detectors
®
Safety Alert Traffic Warning Systems
®
HighGear Accessories
®
CobraMarine VHF Radios
Power Inverters
Accessories
For more information or to
order any of our products,
please visit our website:
Nothing Comes Close to a Cobra®
English
English
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|