ELED Fresnel
Introduction
Unpacking: Thank you for purchasing the ELED Fresnel by Elation
Professional®. Every ELED Fresnel has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the ship-
ping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing,
please contact our customer support number for further instructions.
Do not return this unit to your dealer without first contacting customer
support.
ELED FRESNAL
Introduction: The ELED Fresnel is part of Elation Professionals® con-
tinuing pursuit for creating high quality affordable intelligent fixtures.
The ELED Fresnel is a powerful DMX intelligent LED spot. The unit can
be controlled manually or via DMX controller.
Customer Support: ©Elation® provides a customer support line, to
provide set up help and to answer any question should you encounter
problems during your set up or initial operation. You may also visit us
tions. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m.
Pacific Standard Time.
Voice:
Fax:
(323) 582-3322
(323) 832-9142
E-mail:
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
©Elation customer support.
PLEASE recycle the shipping carton when ever possible.
User Instructions
©Elation Professional®
6122 S. Eastern Ave.
Los Angeles CA. 90040
10/08
Download from Www.Somanuals.com. All Manuals Search And Download.
ELED Fresnel
Set Up
ELED Fresnel
Set Up
Power Supply: Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your Elation® ELED
Fresnel™. The ELED Fresnel™ voltage is between 100v ~ 240v. Be
sure to only use the included I.E.C. power cable supplied with the unit,
this cable matches the current requirements of the unit.
Notice: Be sure to follow figures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav-
els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-
minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
1
2
1
DMX +
DMX -
DMX512 OUT
3-PIN XLR
DMX512 IN
3-PIN XLR
3
3
2
Figure 2
XLR Female Socket
XLR Male Socket
XLR Pin Configuration
Pin 1 = Ground
1 Ground
2 Cold
2 Cold
1 Ground
Pin 2 = Data Compliment (negative)
3 Hot
3 Hot
Pin 3 = Data True (positive)
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX
fixtures try to use the shortest cable path possible. The order in which
fixtures are connected in a DMX line does not influence the DMX ad-
dressing. For example; a fixture assigned a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or any-
where in the middle. When a fixture is assigned a DMX address of 1,
the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Figure 3
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
Data Cable (DMX Cable) Requirements (For DMX Operation):
The ELED Fresnel™ can be controlled via DMX-512 protocol. The ELED
Fresnel™ can be a two, three, four, six, seven or 11 channel DMX unit.
The DMX address is set on the back panel of the ELED Fresnel™. Your
unit and your DMX controller require a approved DMX-512 110 Ohm
Data cable for data input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting stan-
dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
own cables, be sure to use standard 110-120
Ohm shielded cable (This cable may be pur-
3-Pin XLR to 5-Pin XLR Conversion
chased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end
of the cable. Also remember that DMX cable must
Conductor
Ground/Shield
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Pin 1
Pin 1
Pin 2
Pin 3
Data Compliment (- signal)
Data True (+ signal)
Not Used
Pin 2
Pin 3
Do Not Use
Do Not Use
be daisy chained and cannot be split.
Not Used
Figure 1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELED Fresnel
Operating Instructions
ELED Fresnel
Operating Instructions
2. Use the UP and DOWN buttons to adjust the maximum value of the
LED dimmer. The setting can be adjusted between 50-100%.
Operating Modes:
You can use the ELED Fresnel in two ways:
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the Elation® Show Designer™.
Dim Min Setting:
The Dim Min Setting will set the minimum dimness level for manual con-
trol and DMX mode.
Master-Slave Operation:
1. Plug the fixture in and press the MODE button until “XXX6” is dis-
played.
2. Use the UP and DOWN buttons to adjust the minimum value of the
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units built-in programs.
Any unit can act as a Master or as a Slave however, only one unit can be
programmed to act as the “Master.”
LED dimmer. The setting can be adjusted between 0-30%.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. This function
also allows you to use your fixtures as spot lights. The ELED Fresnel has
2 DMX modes: 1 Channel mode and 2 Channel mode. See page 9 for
each modes’ DMX traits. Remember the maximum and minimum dim-
ness levels are set in the Dim Max & Dim Min Settting menus.
1. This function will allow you to control each individual fixture’s traits
with a standard DMX 512 controller such as the Elation® Show
Designer™ or the Elation® DMX Operator™.
2. To run your fixture in DMX mode, plug in the fixture via the XLR con-
nections to any standard DMX controller. Select your desired DMX
mode, and then press the UP or DOWN buttons to adjust the DMX
address. XXX = DMX Address
3. To run the 1 Channel Mode, press the MODE button until “XXX1”
is displayed. This is the DMX addressing for the 1 Channel Mode.
4. To run the 2 Channel Mode, press the MODE button until “XXX2”
is displayed. This is the DMX addressing for the 2 Channel Mode.
3. Please see pages 10-12 for DMX values and traits
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR microphone cables to link your units together.
Remember that the Male XLR connector is the input and the Female
XLR connector is the ouput. The first unit in the chain (master) will
use the female XLR connector only. The last unit in the chain will use
the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. For the “Slave” unit(s), press the MODE button until “XXX3” is dis-
played.
4. Use the UP and DOWN buttons to adjust the address. The slave unit
must be set to the same address as the Master unit.
5. Connect the “Slave” unit or units and they will automatically start to
follow the “Master.”
Manual Dimmer:
1. Plug the fixture in and press the MODE button until “XXX4” is dis-
played.
2. Use the UP and DOWN buttons to adjust the LED intensity.
This onboard control mode is regulated by the max and minimun
intenstiy settings. These settings are set in the DIM MAX SETTING
and DIM MIN SETTING onboard control modes.
Dim Max Setting:
The Dim Max Setting will set the maximum dimness level for manual
control and DMX mode.
1. Plug the fixture in and press the MODE button until “XXX5” is dis-
played.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELED Fresnel 1 Channel Mode - DMX Values and Functions
ELED Fresnel
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses must be carried out periodically to optimize light
output.
Channel
Value
Function
1
0 - 255
DIMMER 0% - 100%
ELED Fresnel 2 Channel Mode - DMX Values and Functions
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Channel
Value
Function
1
2
0 - 255
0 - 255
DIMMER 0% - 100%
STROBING SLOW - FAST
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
ELED Fresnel
Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELED Fresnel
Warranty
ELED Fresnel
Specifications
2-YEAR LIMITED WARRANTY
ELED Fresnel
SPECIFICATIONS:
Model:
A. Elation Professionals® hereby warrants, to the original purchaser, Elation Profes-
sionals® products to be free of manufacturing defects in material and workmanship
for a period of two years (730 days) from the date of purchase. This warranty shall be
valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought.
Working Position:
Voltage:
Any safe working position
100V ~ 240V/47~63Hz
1 x 50W LED
LED’s:
B. For warranty service, send the product only to the Elation Professionals® factory.
All shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, Elation Professionals® will
pay return shipping charges only to a designated point within the United States. If the
entire instrument is sent, it must be shipped in its original package. No accessories
should be shipped with the product. If any accessories are shipped with the product,
Elation Professionals® shall have no liability whatsoever for loss of or damage to any
such accessories, nor for the safe return thereof.
Power Consumption:
Fuse:
75W
3.15 Amp
Weight:
11.6lbs./ 5.3Kgs.
14.5” (L) x 9.84” (W) x 14.5” (H)
White
Dimensions:
Colors:
DMX Channels:
2 DMX Modes: 1 Channel Mode &
2 Channel Mode
2 Year (730 days)
C. This warranty is void if the serial number has been altered or removed; if the prod-
uct is modified in any manner which Elation Professionals® concludes, after inspec-
tion, affects the reliability of the product; if the product has been repaired or serviced
by anyone other than the Elation Professionals® factory unless prior written authori-
zation was issued to purchaser by Elation Professionals®; if the product is damaged
because not properly maintained as set forth in the instruction manual.
Warranty:
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
D. This is not a service contract, and this warranty does not include maintenance,
cleaning or periodic check-up. During the period specified above, Elation Profession-
als® will replace defective parts at its expense, and will absorb all expenses for war-
ranty service and repair labor by reason of defects in material or workmanship. The
sole responsibility of Elation Professionals® under this warranty shall be limited to the
repair of the product, or replacement thereof, including parts, at the sole discretion
of Elation Professionals®. All products covered by this warranty were manufactured
after January 1, 1990, and bear identifying marks to that effect.
E. Elation Professionals® reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in
any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited
by applicable law, all implied warranties made by Elation Professionals® in connec-
tion with this product, including warranties of merchantability or fitness, are limited in
duration to the warranty period set forth above. And no warranties, whether expressed
or implied, including warranties of merchantability or fitness, shall apply to this prod-
uct after said period has expired. The consumer’s and or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circum-
stances shall Elation Professionals® be liable for any loss or damage, direct or conse-
quential, arising out of the use of, or inability to use, this product.
©Elation Professionals®
A Division of the AmericanDJ® Group of Companies
World Headquarters:
G. This warranty is the only written warranty applicable to Elation Professionals®
Products and supersedes all prior warranties and written descriptions of warranty
terms and conditions heretofore published.
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-3322 Fax: 323-832-9142
Download from Www.Somanuals.com. All Manuals Search And Download.
|