Cobalt Digital Inc.
9033-SD
Standard Definition Analog Video
Converter with Audio Embedding
Owner’s Manual
9033-SD-OM
Version: 1.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Regulatory and Safety Notices
Before using this product and any associated equipment, refer to the “Important Safety Instructions”
listed below so as to avoid personnel injury and to prevent product damage.
Products may require specific equipment, and /or installation procedures be carried out to satisfy
certain regulatory compliance requirements. Notices have been included in this publication to call
attention to these specific requirements.
Symbol Meanings
This symbol on the equipment refers you to important operating and maintenance
(servicing) instructions within the Product Manual Documentation. Failure to heed
this information may present a major risk of damage or injury to persons or
equipment.
The symbol with the word “Warning” within the equipment manual indicates a
potentially hazardous situation, which if not avoided, could result in death or serious
injury.
Warning
The symbol with the word “Caution” within the equipment manual indicates a
potentially hazardous situation, which if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.
Caution
Notice
The symbol with the word “Notice” within the equipment manual indicates a
situation, which if not avoided, may result in major or minor equipment damage or a
situation which could place the equipment in a non-compliant operating state.
This symbol is used to alert the user that an electrical or electronic device or
assembly is susceptible to damage from an ESD event.
ESD
Susceptibility
Important Safety Instructions
This product is intended to be a component product of the openGearTM frame. Refer
to the openGearTM frame Owner’s Manual for important safety instructions regarding
the proper installation and safe operation of the frame as well as it’s component
products.
Caution
Warning
Certain parts of this equipment namely the power supply area still present a safety
hazard, with the power switch in the OFF position. To avoid electrical shock,
disconnect all A/C power cords from the chassis' rear appliance connectors before
servicing this area.
Service barriers within this product are intended to protect the operator and service
personnel from hazardous voltages. For continued safety, replace all barriers after
any servicing.
This product contains safety critical parts, which if incorrectly replaced may present
a risk of fire or electrical shock. Components contained within the product’s power
supplies and power supply area, are not intended to be customer serviced and should
be returned to the factory for repair.
Warning
To reduce the risk of fire, replacement fuses must be the same type and rating.
Only use attachments/accessories specified by the manufacturer.
9033-SD Owner’s Manual • (V 1.1)
Page 3 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental Information
The equipment that you purchased required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to diminish the need for the
extraction of natural resources, Cobalt Digital encourages you to use the appropriate take-back systems.
These systems will reuse or recycle most of the materials from your end-of-life equipment in an
environmentally friendly and health conscious manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems, please contact your local
or regional waste administration.
You can also contact Cobalt Digital for more information on the environmental performances of our
products.
Page 4 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction
6
In This Chapter...........................................................................................................................6
A Word of Thanks......................................................................................................................6
Overview....................................................................................................................................6
Functional Block Diagram .........................................................................................................7
Supported Audio and Video Formats.........................................................................................8
Input and Output Video ...............................................................................................8
Embedded Audio .........................................................................................................8
Analog Audio...............................................................................................................9
Discrete AES Audio Input ...........................................................................................9
AES Audio Input Advanced Features ........................................................................................9
AES Sample Rate Converter Bypass............................................................................9
Low latency AES Passthrough.....................................................................................9
Documentation Terms................................................................................................................9
Installation and Setup
10
In This Chapter.........................................................................................................................10
Static Discharge .......................................................................................................................10
Unpacking ................................................................................................................................10
Rear Module Installation (Optional) ........................................................................................11
Board Installation.....................................................................................................................12
Cable Connections....................................................................................................................12
Card Control and Status ...........................................................................................................13
Card Status.................................................................................................................13
Menu Navigation .......................................................................................................13
Menu Structure.........................................................................................................................13
In This Chapter.........................................................................................................................17
DashBoard Control System Software.......................................................................................17
Technical Specifications
20
Service Information
22
In This Chapter.........................................................................................................................22
Troubleshooting Checklist .......................................................................................................22
Warranty and Repair Policy.....................................................................................................23
Ordering Information
24
9033-SD and Related Products ................................................................................................24
Contact Us
26
Contact Cobalt Digital Inc........................................................................................................26
Visit us at the Cobalt Digital Inc. website................................................................................26
9033-SD Owner’s Manual • (V 1.1)
Page 5 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
In This Chapter
This chapter includes the following sections:
•
•
•
•
•
A Word of Thanks
Overview
Functional Block Diagram
Supported Audio and Video Formats
Documentation Terms
A Word of Thanks
Congratulations on choosing the openGearTM 9033-SD Standard Definition Analog to Digital
Converter with Audio Embedding. The 9033-SD is part of a full line of modular conversion gear for
broadcast TV environments. The Cobalt Digital openGearTM line includes video decoders and
encoders, audio embedders and de-embedders, distribution amplifiers, format converters, and much
more. Cobalt openGearTM modular conversion gear will meet your signal conversion needs now and
well into the future.
Should you have questions pertaining to the installation or operation of your 9033-SD, please contact
us at the numbers listed on the back cover of this manual. We are happy to help with any questions
regarding this or any other openGearTM card.
Overview
The 9033-SD is a high quality analog to SD-SDI converter which also features an audio embedder
capable of embedding analog or AES audio signals.
The 9033-SD has a full featured, high quality, 12-bit analog to 10-bit serial digital converter. The
converter can convert signals with NTSC or PAL timing, in composite, Y/C, or component flavors.
The embedder on the 9033-SD can best be thought of as an audio router on a card. On the input side of
the router are the up to 16 channels of embedded AES in the input video, the up to 16 channels (8
pairs) of discrete AES input, and up to 8 channels of differential analog audio input. On the output side
are the up to 16 channels of embedded AES audio. The router acts as a full audio cross point: each of
the 16 embedded output channels can receive signal from any one of the 40 (16 embedded AES, 16
discrete AES, 8 Analog) input channels. Each output also allows gain adjustment and optional polarity
inversion.
Page 6 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio rates are always 48kHz nominally but discrete AES inputs pass through sample rate converters
to align them with the output timing. Output AES is always precisely locked in time with the output
video. Analog audio is differential input and sampled at 48 kHz with 0 dbFS digital equivalent to +24
dBu analog. Dolby decoding is available from embedded audio or external AES, with the purchase of
the Dolby decoding option.
The product also provides full color processing control of the output video, with separate controls for
Gain, Lift, Saturation and Color Phase.
All card features are controlled through the card edge menu interface. There is a 4 character display, a
toggle switch, and two buttons to allow for intuitive control of all device features. All of the controls
on the card edge menu can also be accessed through the free remote control software Dashboard,
provided the openGearTM frame has a 8310-N network card installed.
The card has persistent storage of all settings. There is a menu option to trigger a save or load of stored
settings, or to restore the factory default configuration.
The input and outputs of the 9033-SD are the following:
Input:
ꢀ
ꢀ
ꢀ
One 3-BNC SD analog video input
8 dedicated AES input connections (16 AES channels)
8 differential analog audio inputs
Outputs:
ꢀ
Two SD-SDI video outputs
Functional Block Diagram
The 9033-SD has a very flexible signal flow path and feature set that combines several products into
one compact package. This section describes the basic operation of your 9033-SD product.
9033-SD Owner’s Manual • (V 1.1)
Page 7 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Video
Video
Video Proc:
Gain, Lift, Saturation, Phase
Analog to
Digital
Conversion
SD Analog
Video
Audio Control:
Serializer
and Cable
Driver
Audio
Embed
SD SDI
Output
Diff. Analog
Audio A/D
Routing
Gain
8 channels
Polarity
AES
Decode
and SRC
8 pairs
16 channels
9033-SD Block Diagram
Figure 1. Simplified Block Diagram of 9033-SD Functions
The 9033-SD is an analog to digital converter that also features an embedder which can embed both
analog audio and AES. For the audio embedded on the SDI output, the card acts as a router that can
map any input channel to any channel on the embedded SDI output. The router inputs are discrete AES
audio, and differential analog audio.
Each router for the embedded output provides a gain and polarity control, and each router output can
be sourced from any input channel. This router feature gives your 9033-SD a great deal of flexibility.
There is also a video proc module to allow any necessary corrections to the inbound video signal. It has
separate controls for Luma gain (Y channel), Saturation (C channel gain), Lift (Y channel offset), and
Phase adjustment (C channel).
Supported Audio and Video Formats
Input and Output Video
The 9033-SD supports both modern SMPTE standard SD formats.
Raster structure Frame Rate
486i1
575i1
29.97
25
Notes:
1. All rates displayed as frame rates, interlaced (“i”) field rates are two times the number shown.
Embedded Audio
The 9033-SD supports all four groups (16 channels) of embedded audio at full 24 bit resolution.
Page 8 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog Audio
The 9033-SD supports 8 channels differential analog audio. The analog audio is encoded in such a way
as to make +24 dBu (analog) equivalent to 0 dBFS (digital). Analog audio conversion can be disabled
to reduce power consumption.
Discrete AES Audio Input
The 9033-SD can accept 16 channels (8 pairs) of discrete AES audio on 75 ohm BNC connections. The
AES must have a nominal rate of approximately 48 kHz. Sample rate conversion is employed to
account for minor clock rate differences in the AES stream and the input video stream. However, the
card does not support AES input at 32 kHz, 44.1 kHz, 96 kHz or 192 kHz rates.
AES Audio Input Advanced Features
AES Sample Rate Converter Bypass
The card’s AES inputs have built in sample rate converters that are enabled by default. This allows the
card to interface with asynchronous AES sources (sources who’s AES timing does not match the video
reference timing.). They can be bypassed with a control in Dashboard or the front panel. This is a
necessity when trying to embed non-PCM AES audio such a Dolby E or Dolby Digital audio streams.
This control is off by default.
Low latency AES Passthrough
Sometimes it is desirable to embed AES with minimum latency. For example, if you want to embed
Dolby E audio into video with no latency, and delay the video by one frame to account for Dolby E
encoding delay. If selected for input pair X it causes AES output pair X to act as a bit for bit copy of
AES input pair X. This over rides the normal audio routing and delay. No gain and polarity adjustments
are possible. This control is off by default.
Documentation Terms
The following terms are used throughout this guide:
•
•
•
“Frame” refers to the 8310 frame that houses the 9033-SD card.
“Operator” and “User” both refer to the person who uses the 9033-SD.
“Board” and “Card” all refer to the 9033-SD card itself, including all components
and switches.
•
“System” and “Video system” refers to the mix of interconnected production and
terminal equipment in which the 9033-SD operates.
9033-SD Owner’s Manual • (V 1.1)
Page 9 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
In This Chapter
This chapter includes the following sections:
•
•
•
•
•
•
•
Static Discharge
Unpacking
Rear Module Installation (Optional)
Board Installation
BNC Connections
Menu Structure
Factory Defaults
Static Discharge
Whenever handling the card and other related equipment, please observe all static discharge
precautions as described in the following note:
Static discharge can cause serious damage to sensitive
semiconductor devices. Avoid handling circuit boards in high
static environments such as carpeted areas, and when wearing
synthetic fiber clothing. Always exercise proper grounding
precautions when working on circuit boards and related
equipment.
ESD
Susceptibility
Unpacking
Unpack each card you received from the shipping container, and check the contents against the packing
list to ensure that all items are included. If any items are missing or damaged, contact your sales
representative or Cobalt Digital directly.
Page 10 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Module Installation (Optional)
If you are installing the card in a 8310-C-BNC or 8310-BNC frame (one with a 100 BNC rear module
installed across the entire back plane), skip this section.
If you are installing the card into a slot with no rear module, you should have ordered and received a
8310-RM-10 Rear Module with your card. You will need to install it in your 8310 frame before you
can connect cables.
Use the following steps to install the 8310-RM-10 in an 8310 openGearTM frame:
1. Refer to the openGearTM 8310 frame Owner’s Manual, to ensure that the frame is
properly installed according to instructions.
2. On the rear of the 8310, locate the card frame slot.
3. As shown in Figure 2, seat the bottom of the 8310-RM-10 in the seating slot at the
base of the frame’s back plane.
Figure 2. Rear Module Installation
4. Align the top hole of the 8310-RM-10 with the screw hole on the top edge of the
8310 back plane.
5. Using a Phillips driver and the supplied screw, fasten the 8310-RM-10 panel to the
8310 back plane. Do not over tighten.
This completes the procedure for installing the 8310-RM-10 in an 8310 openGearTM frame.
9033-SD Owner’s Manual • (V 1.1)
Page 11 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Board Installation
Use the following steps to install the card in the openGearTM 8310 frame:
1. Refer to the Owner’s Manual of the openGearTM 8310 frame to ensure that the frame
is properly installed according to instructions.
Heat and power distribution requirements within a frame may dictate
specific slot placement of cards. Cards with many heat-producing
components should be arranged to avoid areas of excess heat build-up,
particularly in frames using convection cooling.
Warning
2. After selecting the desired frame installation slot, hold the card by the edges and
carefully align the card edges with the slots in the frame. Then, fully insert the card
into the frame until the rear connection plugs are properly seated on the midplane and
rear modules.
This completes the procedure for installing the card in the openGearTM 8310 frame.
Cable Connections
This section provides instructions for connecting cables to the installed BNC rear modules on the 8310
series frame backplane. Connect the input and output cables according to the following diagram. The
input is internally terminated with 75 Ohms. It is not necessary to terminate unused outputs.
1
3
5
7
9
2
4
SD-SDI Input
Pr/C
Y/CMPST
Pb
6
AES IN/OUT 1
AES IN/OUT 3
SD SDI Output 1
AES IN/OUT 2
AES IN/OUT 4
8
10
SD SDI Output 2
Figure 3. BNC Designations for the Card Rear Module 8310-RM-10 or 8310-RM-100
In the near future, Cobalt Digital Inc. will release a series of rear modules that allow access to the full
IO capabilities of the card.
Page 12 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Card Control and Status
Card Status
The card indicates the status of the input signal with the four blue LEDs labled with the different
supported formats (625, 525). When the card has locked to a particular input format, that LED will be
illuminated. When the card has not locked to a particular video format, the card will search all possible
formats, and the lights will cycle rapidly.
Menu Navigation
The card can be configured from a menu system built in to the front card edge. This provides an
intuitive and easy to use method for exploring and using the features of the card.
The menu is navigated by using the toggle switch and the two push buttons. The lower button is the
“Enter” button to enter a submenu, and the upper button is the “Exit” button to exit a submenu. Moving
the toggle switch up or down moves up or down in menu choices, and pressing the buttons moves in or
out of sub menus.
The menu LEDs will illuminate from top to bottom to indicate increasing depth in the menu.
Menu Structure
Video Submenu
Menu Structure
Parameter Type
Proc Unity
Proc Gain
Proc
Unty
Gain
Lift
Proc Lift
Sat
Proc Sat
Phas
Proc Phase
Proc Unity
Resets all of the proc controls to unity value.
Proc Gain
This is Luma (Y channel) gain, expressed as a percentage. It ranges from 0.0% to 200.0% in 0.1%
steps.
Proc Lift
This is Luma (Y channel) offset, expressed as an actual video value ranging from -1024 to 1024. If set
to 0 no change is made. If set to 1024 absolute black (value 004) becomes absolute white (value 3FB).
If set to –1024, absolute white becomes absolute black.
Proc Saturation
This is Chroma (C channel) gain, expressed as a percentage. It ranges from 0.0% to 200.0% in 0.1%
steps.
9033-SD Owner’s Manual • (V 1.1)
Page 13 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Proc Phase
This is Chroma (C channel) phase adjustment, expressed in degrees, ranging from –360 to +360 in
steps of one degree.
Audio Submenu
Menu Structure
Parameter Type
Embedded Group Enable
Output Source
Aud
Embd Grp1
Enbl
Ch01-
Ch04
(x4)
Enbl
Ch05-
Ch08
(x4)
Enbl
Ch09-
Ch12
(x4)
Enbl
Ch13-
Ch16
(x4)
Src
Gain
Pol
Output Gain
Output Polarity
Embedded Group Enable
Output Source
Grp2
Src
Gain
Pol
Output Gain
Output Polarity
Embedded Group Enable
Output Source
Grp3
Src
Gain
Pol
Output Gain
Output Polarity
Embedded Group Enable
Output Source
Output Gain
Output Polarity
Tone Frequency
Grp4
Src
Gain
Pol
Tone
TG1-TG4 (x4)
Embedded Group Enable
Enables or disables the embedding of a particular embedded audio group. Disabling a group preserves
the settings of the channels belonging to that group.
Output Source
Because the cards audio system functions like a router, each output can be sourced from any input
channel. This parameter lets you choose from the many different sources. Here is an explanation of the
different source names:
Source Name Description
EmXX
AeXX
AnX
Input embedded audio channel XX (1 through 16)
Discrete AES channel XX (1 through 16)
Analog Audio channel X (1 through 8)
Test Generator channel X (1 through 4)
TgX
Output Gain
The gain of each output is adjustable from +30 dB to –100 dB in 0.1 dB steps. After –100 dB gain is
set to –Inf, which means that output is present, but muted.
Output Polarity
If set to “Norm” output polarity is the same as input polarity, if set to “Inv” the output polarity is
inverted. This can be used to correct polarity errors in the input signals fed to the card.
Page 14 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Tone Frequency
This sets the frequency of the test tone for each of the four tone generators. Each of the four tone
generators TG1 – TG4 can be set to a different frequency, and are available as audio sources for the
embedded or AES audio outputs. The tones can range from 50Hz to 16kHz.
Display Submenu
Menu Structure
Disp H/V
BRGT
Parameter Type
Display Orientation
Display Brightness
Display Orientation
This parameter lets you change the orientation of the display. “Vert” makes the characters look correct
when the cards are mounted in a 2 RU frame like the 8310. “Horz” makes the characters look right in a
horizontal frame.
Display Brightness
This parameter allows you to set the standard output brightness of the menu display. It is a percentage
of maximum brightness.
Preset Submenu
MENU STRUCTURE
Prst Slct
Parameter Type
Select Preset
Save
Load
Fact
Save Settings
Load Settings
Restore Factory Settings
Select Preset
Select from one of the five saved presets.
Save Settings
In this parameter, move the toggle switch up to save the settings to the card persistent storage.
Load Settings
In this parameter, move the toggle switch up to load the saved settings and make them active.
Restore Factory Settings
In this parameter, move the toggle switch up to make the factory default settings active, and make the
stored settings equal to the factory settings.
9033-SD Owner’s Manual • (V 1.1)
Page 15 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Information Submenu
Menu Structure
Parameter Type
Info
+POW
-POW
SWR#
SWB#
Positive Watts Consumed
Negative Watts Consumed
Software Release Number
Software Build Number
Positive Watts Consumed
A read only indication of power consumed by the card from the frames +12V rail.
Negative Watts Consumed
A read only indication of power consumed by the card from the frames +-7.5V rail.
Software Release Number
A read only indication of the software release number. A higher number is newer release of software.
Software Build Number
A read only indication of the software build number. Software build number is an internal indicator
used by Cobalt engineers to differentiate different software builds.
Page 16 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
In This Chapter
This section provides a detailed explanation on using remote control functions with your card.
DashBoard Control System Software
The DashBoard Control System enables you to monitor and control openGearTM frames and controller cards from a
computer. The DashBoard software and manual can be downloaded from the Cobalt Digital Inc. website.
Using the Menus and Menu Descriptions
You must first install the DashBoard Control System software on your computer. Refer to the DashBoard User Manual
for software installation procedures and for using the DashBoard interface.
The following pages list the parameters from the menu tabs available in the DashBoard software when connected to a
9033-SD.
Menu
Item
Format
Description
Product
CDI-9035
The product name
Cobalt Digital Inc.
The manufacturer of the
product
Manufacturer
Software Release
Number
###
###
###
The release number of the
firmware in this card
Software Build
Date
The internal build number
of this software
Software Build
Time
The date and time the
software was created
Card Info
(Read-only)
+12 V Power Rail
-7.5 Power Rail
#.## W
#.## W
Positive Supply Power
Negative Supply Power
Video Input
Standard
Detected Video Standard
on SDI or Analog Input
############
############
############
Detected standard of
selected reference.
Reference Standard
SSN
Displays the Silicon Serial
Number of the card.
9033-SD Owner’s Manual • (V 1.1)
Page 17 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Item
Format
Description
Enable
Enables or disables the
entire group of 4 channels.
Group Enable
Disable
Chooses the source for the
embedded audio. The
source for each channel
can be chosen separately.
Embedded 1-16
AES 1-16
Analog 1-8
Silence
Source
(per channel)
Embedded
Audio Group
(Groups 1-4)
Gain applied to embedded
audio output, one slider
for each channel.
Gain
Range (-400) – 400
(per channel)
Inverts the phase of the
embedded audio.
Normal
Invert
Phase
(per channel)
Menu
Item
Format
Description
Selects the frequency of
the tone generated.
Tone
Generator
Tone Generator 1-4
Frequency
Range 50Hz –16KHz
Menu
Item
Format
Description
This gives the board a
unique name that will
show up in the device list.
Card Name
Up to 31 ASCII
Loads parameters
previously saved.
Selected Preset
Preset Name
Range (1 - 5)
Gives a unique name to
the preset being saved.
Up to 31 ASCII
Presets
Saves the parameters as
preset selected and preset
name entered.
Preset Save
Confirm
Loads parameters of
selected preset.
Preset Load
Confirm
Confirm
Reset Current
Preset
Will load factory presets
and overwrite the save.
Page 18 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Item
Format
Description
Composite
Y/C
Selects the format of
input SD analog video, so
the decoder can properly
decode the signal.
YPbPr BetaCam
YPbPr MII
SD Input Type
Video Signal
Controls
YPbPr SMPTE
Specifies the amount of
setup (pedestal) in the
input video. It will be
removed by the decoder.
SD Composite
Contains
0.0 or 7.5 IRE of Setup
Menu
Item
Format
Description
This will bypass sample
rate conversion on AES.
If bypassed AES rate
must match input video
rate or audio dropout will
occur. SRC must be
On
AES Input
Controls
AES Pair 1-8 SRC
Bypass
Off
bypassed to embed Dolby
encoded audio.
Menu
Item
Format
Description
Range 0-2000
Gain applied to Y (Luma).
1000 is unity.
Video Gain
Range (-999) – 999
Range 0-2000
Lift applied to Y (Luma),
in 10 bit code value.
Video Lift
Gain applied to C
(Chroma). 1000 is unity.
Video Proc
Color Gain
Color Phase
Reset to Unity
Phase of C (Chroma) in
degrees.
Range (–360) – 360
Confirm
Resets all of the proc
controls to unity.
9033-SD Owner’s Manual • (V 1.1)
Page 19 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Table 4. Card - Technical Specifications
3
Number of Inputs
Input Type
Differential, Common Mode Rejection (5V AC)
Composite, Component YPbPr (BetaCam™, MII™,
SMPTE/N10), RGB, and Y/C
Video Inputs
12-Bits
Conversion Bit Depth
SD Color Separation
Frequency Response
Differential Phase
Differential Gain
Noise
5-Line Adaptive Comb or Notch Filter
Y- 0-30MHz ± 0.25db PbPr 0-15 MHz ±
< ±0.4° typical
Analog Video
Input
< ±0.4% typical
< -64dB (Luma Flat Field)
< -61dB (Luma Ramp)
Within Noise Floor Measurement
> 20dB to 30MHz
Analog Front End Crosstalk
Return Loss
2:SD-SDI BNC per IEC 60169-8 Amendment 2
Number of Outputs
Impedance
75Ω
Return Loss
Signal Level
DC Offset
Jitter
> 15 dB at 5MHz – 270MHz
800 mV ±10%
Serial Digital
Video Outputs
0 Volts ±50 mV
<0.06UI (all outputs)
Overshoot
<0.2% of amplitude
SMPTE 276M
Standard
Number of Inputs
Input Level
8 unbalanced
0.1 to 2.5V p-p (5V p-p tolerant)
AES Audio
Input
Input Impedance
Return Loss
Equalization
75Ω
> 12dB 100kHz to 6MHz
Automatic to 1000m with Belden 1694A (or
equivalent) @ 48kHz AES signal
48KHz
Sample Rate
Page 20 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Balanced Analog Audio
Phoenix 3-pin
Number of Inputs
Connector
48KHz (free run or locked to the reference)
+24dBu => 0dBFS
Sampling Rate
Signal Level
Analog Audio
Input
Total Power Consumption
Warranty
<12W
Other
Five Year Transferable
Specifications are subject to change without notice.
9033-SD Owner’s Manual • (V 1.1)
Page 21 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Information
In This Chapter
This chapter includes the following sections:
•
•
Troubleshooting Checklist
Warranty and Repair Policy
Troubleshooting Checklist
Routine maintenance to this openGearTM product is not required. In the event of problems with your
card, the following basic troubleshooting checklist may help identify the source of the problem. If the
module still does not appear to be working properly after checking all possible causes, please contact
your openGearTM products distributor, or the Technical Support department at the numbers listed under
the “Contact Us” section at the end of this manual.
1. Visual Review Performing a quick visual check may reveal many problems, such
as connectors not properly seated or loose cables. Check the module, the frame, and
any associated peripheral equipment for signs of trouble.
2. Power Check Check the power indicator LED on the distribution frame front
panel for the presence of power. If the power LED is not illuminated, verify that the
power cable is connected to a power source and that power is available at the power
main. Confirm that the power supplies are fully seated in their slots. If the power
LED is still not illuminated, replace the power supply with one that is verified to
work.
3. Reseat the Card in the Frame Eject the card and reinsert it in the frame.
4. Check Control Settings Refer to the Installation and Operation sections of the
manual and verify all user-adjustable component settings.
5. Input Signal Status Verify that source equipment is operating correctly and that a
valid signal is being supplied.
6. Output Signal Path Verify that destination equipment is operating correctly and
receiving a valid signal.
7. Module Exchange Exchanging a suspect module with a module that is known to
be working correctly is an efficient method for localizing problems to individual
modules.
Page 22 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Repair Policy
The openGearTM card is warranted to be free of any defect with respect to performance, quality,
reliability, and workmanship for a period of FIVE (5) years from the date of shipment from our factory.
In the event that your Cobalt Digital Inc. card proves to be defective in any way during this warranty
period, Cobalt Digital Inc. reserves the right to repair or replace this piece of equipment with a unit of
equal or superior performance characteristics.
Should you find that this openGearTM card has failed after your warranty period has expired, we will
repair your defective product should suitable replacement components be available. You, the owner,
will bear any labor and/or part costs incurred in the repair or refurbishment of said equipment beyond
the FIVE (5) year warranty period.
In no event shall Cobalt Digital Inc. be liable for direct, indirect, special, incidental, or consequential
damages (including loss of profits) incurred by the use of this product. Implied warranties are
expressly limited to the duration of this warranty.
This openGearTM card Owner’s Manual provides all pertinent information for the safe installation and
operation of your Cobalt Digital Inc. Product. Cobalt Digital Inc. policy dictates that all repairs to the
openGearTM card are to be conducted only by an authorized Cobalt Digital Inc. factory representative.
Therefore, any unauthorized attempt to repair this product, by anyone other than an authorized Cobalt
Digital Inc. factory representative, will automatically void the warranty. Please contact Cobalt Digital
Inc. Technical Support for more information.
In Case of Problems
Should any problem arise with your openGearTM card, please contact the Cobalt Digital Inc. Technical
Support Department. (Contact information is supplied at the end of this publication.)
A Return Material Authorization number (RMA) will be issued to you, as well as specific shipping
instructions, should you wish our factory to repair your openGearTM card. If required, a temporary
replacement module will be made available at a nominal charge. Any shipping costs incurred will be
the responsibility of you, the customer. All products shipped to you from Cobalt Digital Inc. will be
shipped collect.
The Cobalt Digital Inc. Technical Support Department will continue to provide advice on any product
manufactured by Cobalt Digital Inc., beyond the warranty period without charge, for the life of the
equipment.
9033-SD Owner’s Manual • (V 1.1)
Page 23 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Information
9033-SD and Related Products
Your 9033-SD Standard Definition Analog to Digital Converter with Audio Embedding is a part
of the openGearTM family of products. Cobalt Digital offers a full line of openGearTM terminal
equipment including distribution, conversion, monitoring, synchronizers, encoders, decoders,
embedders, and de-embedders, as well as analog audio and video products.
Standard Equipment
•
•
9033-SD Standard Definition Analog to Digital Converter with Audio Embedding
9033-SD-OM Standard Definition Analog to Digital Converter with Audio Embedding
Owner’s Manual
Optional Equipment
•
9033-SD-OM Standard Definition Analog to Digital Converter with Audio Embedding
Owner’s Manual
(additional Owner’s Manual)
•
•
8310-RM-10 openGearTM Rear Module compatible with 9033-SD
(10 BNC connector)
8310-C Digital Products Frame and Power Supply with Cooling Fans
(2RU, holds 10 cards)
•
•
8310-C-BNC Digital Products Frame and Power Supply with fixed 100-BNC Rear
Module and Cooling Fans. (2RU, holds 10 cards)
MFC-8310-N Network Controller Card (Additional)
Page 24 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
9033-SD Owner’s Manual • (V 1.1)
Page 25 of 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact Us
Contact Cobalt Digital Inc.
General Business Office
and Technical Support
217.344.1243
217.344.1245
PHONE
E-MAIL
Fax
General Information
Sales Information
2406 East University Avenue
Urbana, IL 61802 USA
POSTAL
SERVICE
Cobalt Digital Inc.
Visit us at the Cobalt Digital Inc. website.
•
•
•
•
•
Online catalog
Related products and full product lines
Trade show information
Dealer information
Cobalt Digital Inc. news
Page 26 of 26
9033-SD Owner’s Manual • (V 1.1)
Download from Www.Somanuals.com. All Manuals Search And Download.
|