ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
INSTALLATION INSTRUCTIONS
ED2XX 30” CCM330/430/530/630/830/1030 NORDIC BLACK/GRAY
STYLE LID KITS
This Nordic style kit applies to the Cornelius 30” wide CCM322/522 ice maker.
Item
No.
Part No.
53003
52969
15537
29565
70217
50904
90221
Name
Qty.
1
Cover, Gray
Cover, Black
Lid Assembly
Bracket
1
2
3
4
5
6
7
8
9
1
2
6
1
1
1
2
2
1
2
1
1
#8 Screw
RTV
Label
620204731INS Installation Instructions
620701902
620701901
Acorn Nut, 8--32 Nylon
Sealing Washer
Baffle, Ice
10 620037003
11 621701903
12 620505802
13 630500109
#8 Nylon Washer
Insulation Strip
Bin Stat
CAUTION: Disconnect electrical power to the dispenser before proceeding with the icemaker
adapter kit installation.
1.
2.
Unpack Kit.
Place insulation strip (item 12) over studs on the baffle and insert baffle assembly into the adapter
lid.
3.
Place (2) sealing washers (item 9) over studs and (2) flat washers (item 11), then fasten in place
with (2) plastic acorn nuts (item 8)
4.
5.
Set icemaker lid on the top of the dispenser.
Using the slotted holes in the lid as a template, drill four (4) .140_ diameter (9/64_) holes at the
bottom of the slots (see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the
dispenser with four (4) #8 sheet metal screws, two on each side.
Seal the icemaker to the top of the dispenser as follows:
6.
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the icemaker
outline so that the icemaker will set on the RTV.
B. Set the icemaker onto the lid and position it as required.
C. Wipe away the excess RTV.
7.
8.
Drill 9/64” diameter holes into the icemaker cabinet using the bracket as a template. Use extreme
care not to drill into any icemaker components (condenser, tubing, etc.). Secure the brackets using
the screws provided.
Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in
the bottom of the ice maker. Wrap the eye of the wireform over the stud near the hole to the end of
the wireform bracket and wrap the tube around the end of the bracket several times, insuring the
tube is secure.
NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from
the icemaker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.
Release Date: October 5, 2007
© 2007, IMI Cornelius Inc.
Revision: A
Publication Number: 620204731INS
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
ICEMAKER
SEAL ICEMAKER TO
ITEM 2 WITH ITEM 5 (RTV)
DETAIL ”A”
ENLARGED
DRILL 9/64 (.140) DIA.
HOLES USING BOTTOM
OF SLOTTED HOLES AS A
TEMPLATE.
4
(2) PLCS.
3
2
3
4
(6) PLCS.
4
6
1
VIEW ”A”
FIGURE 2. ED2XX Kit
© 2007, IMI Cornelius Inc.
- 3 -
Publication Number: 620204731INS
Download from Www.Somanuals.com. All Manuals Search And Download.
ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
FIGURE 3. Bin Stat
Publication Number: 620204731INS
- 4 -
© 2007, IMI Cornelius Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|